INSTALLATION INSTRUCTIONS FOR PART 99-8218
APPLICATIONS
TOYOTA
CAMRY / CAMRY HYBRID
2007-2011
99-8218
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Units Provision
KIT COMPONENTS
A) Radio Housing • B) Radio Housing Brackets • C) ISO Snap-In Brackets • D) Double DIN Brackets
E) Trim Plate • F) Double DIN Trim Plate • G) Pocket • H) (4) # 8 x 3/8 Phillips Screws • I) (4) #4 x 1/4 Phillips Screws
B
E
D
C
H
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wire harness:
• 70-1761 Toyota 1987-up
A
• TYTO-01 Toyota amp interface harness 2003-up
Antenna adapter:
• Not required
I
G
F
TOOLS REQUIRED:
Phillips Screwdriver • Socket
Small Flat Blade Screwdriver or
Panel Removal Tool
1-800-221-0932
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
DASH DISASSEMBLY
99-8218
TOYOTA CAMRY/CAMRY HYBRID 2007-2011
A
Disconnect the negative battery terminal
to prevent an accidental short circuit.
1
Turn the shift knob counterclockwise to
remove.
2
3
Unclip and remove (1) trim panel from each
side of the pocket below the radio/climate
control assembly. (2 panels total)
(Figure A)
B
4
5
Unclip and remove the shift knob trim
panel. (Figure B)
Unclip and remove the top of the center
console including the cup holders.
(Figure B)
C
6
7
Remove (1) Phillips screw from each
side of pocket below the radio/climate
control assembly (2 screws total).
(Figure C)
Unclip and remove the pocket.
(Figure C)
Continued on Page 2.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
DASH DISASSEMBLY
99-8218
TOYOTA CAMRY / CAMRY HYBRID 2007-2011
A
8
Unclip and remove the A/C vents above
the radio. (Take care not to scratch the
dash panel. (Figure A)
9
Remove (2) 10mm bolts above the radio
(behind the A/C vents) and (2) 10mm
bolts below the climate controls (behind
pocket) then unplug and remove the
radio/climate control assembly.
(Figure B)
B
10
11
Remove the (10) Phillips screws securing
the brackets to the radio/climate control
assembly and separate the radio from the
climate controls. (Retain climate controls
and screws for use during kit assembly).
(Figure C)
C
Unscrew and remove the (2) Clips from
the back of the factory radio. (Retain clips
for use during kit assembly. (Figure C)
Continue to kit assemby.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT ASSEMBLY
99-8218
DIN RADIO PROVISION WITH POCKET
A
NOTE: Refer also to the instructions
included with the aftermarket radio.
Slide the DIN cage into the Radio
Housing and secure by bending
the metal locking tabs down.
1
2
(Figure A)
B
Slide the after-market radio into the
cage until it snaps into place.
(Figure B)
Snap the pocket into the radio
housing. (Figure B)
3
4
Align the small legs on the bottom
of the radio housing with the slots in
the top of the climate control. Then
slide the climate control sideways to
engage together. (Figure C)
C
Attach the radio housing brackets to
the radio housing using the included
Phillips screws. (Figure D)
5
6
7
Secure the radio housing brackets to
the climate control using the factory
hardware. (Figure D)
D
Attach the (2) clips removed in step
11 in dash disassembly to the radio
housing brackets using the supplied
small Phillips screws.(Figure D)
Continue to Final Assembly.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT ASSEMBLY
99-8218
ISO RADIO PROVISION WITH POCKET
A
NOTE: Refer also to the instructions
included with the aftermarket radio.
Mount the ISO Brackets to the
radio with the screws supplied
with the radio. (Figure A)
1
2
Slide the radio into the radio open-
ing until the side clips engage.
B
(Figure B)
Snap the Trim plate into the Radio
Housing. (Figure B)
3
4
Snap the pocket into the radio
housing. (Figure B)
Align the small legs on the bottom
of the radio housing with the slots in
the top of the climate control. Then
slide the climate control sideways to
engage together. (Figure C)
5
C
D
Attach the radio housing brackets to
the radio housing using the included
Phillips screws. (Figure D)
6
7
8
Secure the radio housing brackets to
the climate control using the factory
hardware. (Figure D)
Attach the (2) clips removed in step
11 in dash disassembly to the radio
housing brackets using the supplied
small Phillips screws.(Figure D)
Continue to Final Assembly.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT ASSEMBLY
99-8218
DOUBLE DIN
RADIO PROVISION
A
B
NOTE: Refer also to the instructions
included with the aftermarket radio.
Cut and remove center divider
from radio housing. (Figure A)
1
2
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
Slide the Double DIN radio into the
Double DIN bracket/radio housing
assembly and secure the radio to the
assembly using the screws supplied
with the radio. (Figure C)
3
C
D
E
Snap the Double DIN trim-plate into
the housing/radio assembly. (Figure C)
4
5
Align the small legs on the bottom of
the radio housing with the slots in the
top of the climate control then slide the
climate control sideways to engage
together. (Figure D)
Attach the corresponding radio housing
bracket to the radio housing using the
included Phillips screws. (Figure E)
6
Secure the radio housing brackets to
the climate control using the factory
hardware. (Figure E)
7
8
Attach the (2) clips removed in step 11 in
dash disassembly to the radio housing
brackets using the supplied small Phillips
screws.(Figure E)
Continue to Final Assembly.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT ASSEMBLY
99-8218
STACKED ISO
UNITS PROVISION
A
B
NOTE: Refer also to the instructions
included with the aftermarket radio.
Cut and remove center divider
from radio housing. (Figure A)
1
2
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
Slide the Stacked ISO units into the
Double DIN bracket/radio housing
assembly and secure the radio to the
assembly using the screws supplied
with the units. (Figure C)
3
C
D
E
Snap the Double DIN trim-plate into
the housing/radio assembly. (Figure C)
4
5
Align the small legs on the bottom of
the radio housing with the slots in the
top of the climate control then slide the
climate control sideways to engage
together. (Figure D)
Attach the corresponding radio housing
bracket to the radio housing using the
included Phillips screws. (Figure E)
6
Secure the radio housing brackets to
the climate control using the factory
hardware. (Figure E)
7
8
Attach the (2) clips removed in step 11
in dash disassembly to the radio housing
brackets using the supplied small
Phillips screws.(Figure E)
Continue to Final Assembly.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FINAL ASSEMBLY
99-8218
FINAL ASSEMBLY
A
B
A)
B)
C)
D)
Strip wire ends back 1/2"
Twist ends together
Solder
Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown.
(Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . Red
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . White
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Left Front (-). . . . . . . White / Black
Right Rear (+). . . . . . Violet
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8218
NOTES
8
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8218
NOTES
9
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8218 INSTRUCTIONS
1-800-221-0932
REV. 07-22-10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
INST99-8218
Download from Www.Somanuals.com. All Manuals Search And Download.
|