User and Installation Manual
The home theater projector
FDP-DLPHD20
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK LIGHT
Turn on the back light
STAND-BY
LIGHT
Switches off to stand-by.
0-9 Keys
Switch on from stand-by
and allow direct source
selection.
SOURCE
Displays the Source
Selection menu.
ESCAPE
Deactivates the On Screen Display.
Not active
in this model.
Up/Down/Left/Right Arrow keys
Navigate through and make adjustments
to the On Screen menus.
Arrow Up/Down activate Quick
menus.
MENU -
Activates the On Screen
Display menus.
Navigates menu pages.
MENU +
Activates the On Screen Display menus.
Navigates menu pages.
MEMORIES
FREEZE
Activates Memories menu
Freezes a moving
picture.
ZOOM
F1
F1
Select lens zoom
adjustment
INFO
F2
Displays the selected source information
and the projector status.
FOCUS
F2
Select focus
lens adjustment
VCR
Improves the video recorder
signals quality.
AUTO
Selects Auto Adjust
(automatic optimisation
of the displayed image).
ASPECT
Selects image Aspect ratio.
Download from Www.Somanuals.com. All Manuals Search And Download.
1 INTRODUCTION
Congratulations and thank you for choosing a FDP-DLPHD20
projector, a Faroudja product (Fig. 1).
e
ettr
prom
com ncend
d'i
e
pas
r
ne
qu
e
type
N
:
p
o
u
l
e
s
r
es
em
e
TIO
EN
re
de
m
A
TT
ion
cont
fusi
ri
ble
rotect
r
un
stiqu
e
nst
a
gai
la
p
pa
n
o
placer caracte
s
otecti
rem
et
d
pr
e
mem
tinue
con
fo
lac
d
:
r
e
pe
ION
UT
rep
CA
ire,
e
th
sam
fuse.
ing
o
f
f
ty
Cr
risk
R/
y
wi
onl
rat
and
O
DI
A
U
ITAL
T
OUT
B
/Y
5
IG
RG
G
3
CS
HI
(R
INPU
AP
4
GR
OM
ZO
2
Cb
B/
232)
S
L
RO
NT
CO
1
HV
1
Download from Www.Somanuals.com. All Manuals Search And Download.
A sophisticated proprietary optical system, coupled with a hight
performance zoom lens ensures hight contrast images, superior
uniformity and edge-to-edge definition.
™
A new 6-segment colour wheel dramatically reduces the so
called “rainbow effect” and gives a better contrast, better
colorimetry and a lower black level to the image.
The new HD2+ DMD™ chip ensures, on top of the high definition
resolution (1280 x 720 pixels), an increased contrast ratio of >
2800:1 thus delivering on the screen an even more realistic
image.
Fig. 1
The low-noise ventilation system – with variable speed fans –
ensures appropriate cooling and maximizes projector reliability.
The FDP-DLPHD20 incorporates patented Faroudja technology
for deinterlacing, color and detail processing, including DCDi
technology. The result is that all sources are converted to very
clean video signals full of detail and color while free of typical
artifacts such as stairstepping and motion breakup.
To fully appreciate your new projector we recommend the use
of a good quality screen and surround-sound system. Contact
your nearest authorized Faroudja dealer for further details.
Faroudja carries out comprehensive functional
testing in order to guarantee the maximum product
quality.
For this reason, when you start using the product
lamp operating hours may already be at between
30 and 60.
Using the very latest in DLP™ technology, this projector has
been designed specifically for high quality “Home Cinema”
applications.
Sophisticated digital processing and a wide choice of inputs
enable the connection of a variety of sources such as DVD
players, analogue and digital VCRs, analogue and digital sa-
tellite receivers and personal computers etc.
The long throw zoom lens allows the position of the projector to
be located behind the viewer, thus reproducing a cinema-like
installation (Fig. 2).
In addition to the regular tests, the Quality Control
department performs additional statistical tests at
the time of shipment.
In this case the packing may show signs of having
been opened, and the accumulated lamp operating
hours may be slightly higher than the hours associ-
ated with the standard tests.
m
c
e
e
n
d
c
I
O
a
:
s
c
re
q
m
e
m
i
e
t
p
e
c
s
l
e
i
c
gainst
p
o
t
r
e
n
e
s
pa
re
s
o
p
'i
n
e
Al
p
r
o
N
t
T
e
t
ir
n
co
u
n
te
u
e
r
e
m
e
l
m
em
s
car
continued
c
p
o
t
e
Cr
i
U
k
o
f
IO
f
i
N
s
,
f
o
r
e
ac
t
y
e
e
R
/
C
r
o
n
l
w
i
i
g
f
u
s
e
.
r
a
t
A
U
D
IO
IT
AL
O
U
T
I
C
S
S
2
R
3
G
B
G
/
Y
3
5
DIG
IN
Z
O
2
O
M
4
G
R
A
P
H
B
/
C
(
R
2
)
1
C
O
N
TR
O
L
H
V
Fig. 2
DLP and DMD are registered trademarks of Texas Instruments.
DCDi is a registered trademark of Faroudja, a division of Genesis
Microchip, Inc.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
3
1
2
5
8
™
7
4
6
1
2
3
4
5
6
7
8
Projection lens
Lens shift knob
Cooling air inlet vents
Remote control IR sensor
Cooling air outlet vents
Adjustable carry-handle
Adjustable levelling feet
Ceiling/wall bracket fixing holes
13 17
11
12
9
Fused power socket
Main power switch
Remote control rear IR sensor
Green LED
10
11
12
13
14
15
16
17
18
19
20
21
22
10
9
e
r
romett
comp
pas
d'incende
type
resque
meme
de
gainst
a
ne
re
fusi
pour
N:
O
les
NTI
E
r
T
p
cont
le
b
AT
otection
r
ca
un
la
r
remplace
ristique
r
pa
cte
a
r
otection
p
mems
f
r
ued
de
et
contin
r
o
:
e,
N
IO
T
AU
eplace
C
ri
r
Red LED
fi
type
r
of
w
atin
k
s
/C
R
ith same
.
fuse
only
and
g
r
O
I
D
AU
OUT
Rear keyboard pad
Composite video input
S-Video input
VGA input
RGB / YCrCb input
Digital Input
Optical Audio Output
12Vdc screen output
RS232 interface connector
AL
DIGIT
GB
R
5
G/Y
3
ICS
INPUT
APH
GR
M
4
14
ZOO
2
b
/C
B
32)
OL (RS
2
ONTR
C
1
V
H
20
19
18
22
16
15
21
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2 IMPORTANT SAFETY INSTRUCTIONS
ATTENTION:
To reduce the risk of electric shock, disconnect the
power supply cable on the rear panel before removing
the top cover of the projector.
Refer to trained, authorised personnel for technical
assistance.
This symbol indicates the possible electric shock
hazard associated with uninsulated live
components in the interior of the unit.
This symbol indicates the presence of important
instructions regarding use and maintenance of
the product.
Prior to switching on the projector please read each chapter of this manual carefully as this manual provides basic
instructions for using the projector.
The installation of the lamp assembly, preliminary adjustments and procedures that necessitate the removal of the
top cover, must be carried out by authorised, trained technicians. There are no user serviceable parts inside. To
ensure safe and long term reliability please use power cables supplied with the projector. Observe all warnings and
cautions.
• Federal Communication Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is used in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determinated by turning the equipment off and on,
the user is encuraged to try to correct the interference by one or more of the following measures:
-
-
-
-
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
• For customers in Canada
This Class B digital apparatus complies with Canadian ICES-003.
• For customers in the United Kingdom
ATTENTION: This apparatus must be earthed
The wires in this mains lead are coloured in accordance with the following code:
Green-and-Yellow:
Blue:
Brown:
Earth
Neutral
Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug
proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth
symbol
or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Please follow carefully the warnings listed below, to ensure safe
and long term performance of your projector.
as compromettre
resque d'incende
p
• Connect the projector to a power supply with a nominal
voltage within the following values: 100-240 Vac, 50/60 Hz,
earthed (Fig. 3).
4
e
de meme type
250 V
T 3.15A H
ique
t
d
protection against
e
1
UDIO
A
OUT
3
pour ne pas compromettre
le de meme type
TTENTION:
A
la protection contre leisstirq
e
ue
s
que d'incende
acter
2
remplacer par un fusib
ued protection against
et de mems car
or contin
f
UTION:
isk of fire
CA
,
replace
r
.
only with same type
ating fuse
r
and
UDIO
A
AL
DIGIT
OUT
5
3
INPUT
Fig. 4
100-240 Vac
50/60 Hz
• Do not obstruct the cooling air inlets on the top cover, or the
air outlets underneath the projector.
• Do not switch on the projector if it is standing on soft surfaces
such as cushions, pillows, blankets, mattresses and carpets:
the air cooling outlets underneath could become obstructed.
Fig. 3
• The mains plug is the disconnect device. Take care, when
installing, that the mains plug and socket outlet are easily
accessible. Never pull on the cable to take it out of the socket.
If the system is unlikely to be used for a number of days,
disconnect the power cable and other apparatus connected
to it.
• Do not switch-on the projector if it is standing on surfaces
sensitive to heat, as this may result in damage caused by
the hot air outlets underneath. Should this be unavoidable
take extra precaution of protecting the surfaces with a layer
of heat resistant material.
• To save energy, switch off the projector by using the power
switch at the rear; when in stand-by (red light on) the
projector continues to draw a minimal amount of power.
• Intense Light Source! Do not stare directly into the projection
lens as possible eye damage could result. Be especially
careful that children do not stare directly into the beam.
• Only replace the safety fuse (on the power socket at the
rear of projector) with a fuse identical in type and
characteristics (T 3.15A H) (Fig. 4).
• Do not open the projector’s cover; no user serviceable parts
are inside. Refer servicing to qualified service personnel.
Opening the projector’s cover will invalidate warranty.
• Take care not to shake the projector whilst carrying it by the
handle.
• Do not switch on your projector when flammable liquids or
fumes are present. Do not pour or drop fluids in the vents.
• Always position the projector away from direct heat sources.
• Do not use the projector when the room temperature is above
35°C (95°F).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not touch the surface of the projection lens.
• For installations using a ceiling or wall-mounted bracket,
carefully follow the installation and safety instructions
provided with the bracket’s literature.
• The projector must be positioned on a stable, suitable
platform or be installed using a bracket for fixed ceiling or
wall installation. Do not rest the projector on the side panels
or on the rear panel when in operation.
• Please remove batteries from the remote control if not in use
for a long period of time.
• Take care to position cables safely, especially in dark places,
in order to avoid a trip hazard.
3 PACKAGING AND CONTENTS
Fig. 5
To unpack the projector safely and easily please follow steps 1
to 4, as drawing (Fig. 5).
The carton should contain the following:
-
-
-
-
-
the projector
the remote control
four 1.5V AAA batteries (for remote control)
one power cable (USA)
the user manual.
It is recommended that the carton and packaging is retained
for future use and in the unlikely event that your projector needs
to be returned for repair.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4 INSTALLATION
Position the projector on a stable, suitable platform or utilise
the optional bracket for a fixed ceiling or wall installation.
focus you should be able to clearly see each single pixel when
within close proximity to the screen (Fig. 7).
CAUTION: In the case of ceiling or wall mounting
using a suspension bracket, follow the instructions
carefully and comply with the safety standards you
will find in the box together with the bracket. If you
use a bracket different to the one supplied by
Faroudja, you must make sure that the projector is
at least 65 mm (2-9/16 inch) from the ceiling and
that the bracket is not obstructing the air vents on
the lid and on the bottom of the projector.
FOCUS
FOCUS
FOCUS
FOCUS
ttre
rome de
a
s
comp 'incen
typ
e
u
r
n
e
p
e
s
q
u
e
d
I
O
n
t
e
mem
st
again
tion
rotec
T
N: po re les
le de
fusib
istique
o
N
c
A
T
T
E
e
c
o
n
l
a
p
r
ot
c
e
r
p
a
r
u
n
cter
ntinu
la
remp ems
m
:
fire,
cara
d
e
c
o
ed
p
e
t
f
o
r
T
I
O
N
r
e
p
l
a
CA
U
ce
k
t
R/Cr
r
i
s
of
w
i
t
h
s
ame
fuse.
o
n
l
y
t
i
n
g
ra
and
O
UDI
A
IT
DIG
T
INPU
A
L
T
OU
R
GB
G/Y
b
3
5
ICS
APH
OM
4
G
R
ZO
2
B/C
2
3
2
)
OL
(
RS
NTR
CO
1
HV
Adjust the feet underneath to obtain a level position, lining up
the base of the projected image to the base of the projection
screen (Fig. 6).
Fig. 7
The manual lens shift adjustment allows the projected image
to be moved vertically, up or down, in relation to the centre of
the screen; the maximum adjustment being equal to half the
height of the image in either direction (Fig. 8).
ttre
ome
m
p
r
e
n
d
e
p
a
s
co
e
'inc
n
e
u
d
N
po
ur
e
resq
typ
e
I
O
n
t
r
m
eme
:
les
e
TT
ENT
n
co
ble
d
A
ctio
fusi
la
p
rote par un
cer
ter
carac
istique
against
pla
rem
ems
protection
d
e
m
ue
d
for contin
ce
et
CA
:
,
U
risk of
TION
repla
e
type
R/Cr
G/Y
i
f
t
i
h
resam
.
fuse
atin
only
and
w
r
g
DIO
A
U
L
T
IT
A
OU
DIG
UT
INP
GB
5
S
R
3
HIC
GRAP
OM
4
ZO
2
B/Cb
O
L
(
R
S
2
3
2
)
TR
1
CON
HV
e
omett
'incen
type
r
d
e
p
a
s
comp
r
u
e
d
s
I
O
N
:
c
pour
o
n
t
r
n
e
l
e
s
e
r
e
d
e
eme
T
l
A
TTE
N
o
m
nst
ction agai
l
a
p
r
l
a
c
e
r
p
a
r
r
a
c
t
e
r
i
s
t
i
q
r
e
m
p
m
e
m
s
c
a
u
e
d
p
r
o
t
e
e
t
d
e
:
f
o
r
c
o
n
t
i
n
N
p
l
a
c
e
C
A
U
T
f
I
O
i
r
,
r
e
type
R
/
C
r
riskyowith same
.
onl rating fus
and
IO
UD
OUT
A
AL
R
G
B
G
/
Y
3
5
DIGIT
INPUT
I
S
2
A
P
H
C
S
O
M
4
G
R
Z
O
2
B
/
C
3
2
)
(
R
R
O
L
1
C
O
N
T
H
V
Fig. 6
Position the projector the desired distance from the screen:
the size of the projected image is determined by the distance
from the lens of the projector to the screen and the zoom setting.
See “Appendix C”: Projection distances” for more information.
Fig. 8
Use the motorised lens zoom to adjust the image size and the
motorised lens focus to achieve maximum clarity. With optimum
In the event you are unable to centre the image within the screen
area, tilt the projector until the image is correctly positioned.
Any keystone error can be removed by the Keystone adjustment
in the Set up menu (Fig. 9).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
KEYSTONE
20%
re
romett
comp
pas
ne
e
d'incende
r
type
:
p
o
u
l
e
s
r
e
s
q
u
ON
n
r
re
meme
ENTI
cont
e
de
A
TT
fusibl
rist
rotectio
r
un
ique
pro
la
p
pa
n
tectio
a
gainst
c
a
racte
r
e
m
p
l
a
c
e
mems
ued
e
t
d
e
r
contin
N
:
f
o
e
TIO
plac
CA
U
r
e
,
r
e
pe
fi
ty
Cr
risk of same
ith
R/
w
se.
o
n
l
y
n
g
f
u
rati
and
O
DI
AU
T
OU
A
L
IT
DIG
PU
B
5
RG
2)
G
/Y
T
CS
3
HI
IN
AP
GR
OM
4
ZO
2
Cb
B/
23
L
(
RS
RO
NT
CO
1
HV
C-SYNC
Fig. 11
Fig. 9
The output is activated (Voltage: 12 Vdc) when the projector is
switched on and is de-activated (no Voltage output) when the
projector is in stand-by mode.
The Orientation adjustment in the Set up menu will allow the
projector to be used for desktop front, ceiling front, desktop
rear and ceiling rear installations (Fig. 10).
Some manufacturers offer screen-masking systems to help fra-
me the projected image and improve picture contrast. These
systems can be connected to output
projector (Fig. 12).
, at the rear of the
r
o
m
ettre
d
e
p
n
com 'ince
type
mem
istique
ed pr
n
e
pas
s
q
u
e
d
N
p
o
u
r
r
e
l
e
s
r
e
N
T
O
:
c
o
n
t
l
e
e
e
I
d
A
T
T
E
e
c
t
i
o
fusib
t
ot
la pr cer
la
p
a
r
u
n
gains
p
s
cter
ntinu
ion
a
r
e
m
e
m
cara
or co
otect
d
e
m
e
t
f
:
ce
CA
U
TION repla
fire,
r
r
i
s
k
o
f
t
R/C
with
ra
s
ame
o
n
l
y
t
i
n
g
f
u
s
e
.
and
DIO
U
A
AL
DIGIT
O
UT
B
G/Y
b
R
G
)
3
5
H
IC
S
UT
AP
OM
4
G
R
ZO
2
B/C
232
(RS
R
OL
1
C
O
NT
H
V
ttre
me
pro
de
com
cen
pas
d'in
ne
ntre
que
pe
N:
p
our
les
res
em
e
ty
TIO
e
m
A
TT
EN
ction
co
usib
le
d
r
u
n
f
ue
st
gain
la
p
rote
er
p
ems
fo
r
ith sa
a
teri
stiq
n
ctio
a
c
rac
pla
e
ca
te
rem
d
pro
ntinue
m
et
d
r
ep
co
:
e
ION
lac
UT
CA
ris
pe
fir
e,
ty
r
k
of
me
R/C
w
se.
only
g
fu
in
rat
and
U
OU
DIO
T
A
A
L
IT
DIG
PU
B
/Y
b
5
RG
2)
G
T
S
3
HIC
RS
IN
AP
GR
4
ZOOM
2
B/C
23
L
(
RO
NT
CO
1
HV
Fig. 10
To activate an electric motorised screen a 12 Volt output is
provided at the rear of the projector. This can be connected to
a screen interface unit, which can be supplied by screen
manufacturers (Fig. 11).
Fig. 12
For rear projection the screen must be translucent.
For front projection, we recommend the use of screens with
low gain specifications (i.e. 1.3 to 2). The use of high gain
screens should be avoided due to their limited viewing angle,
8
Download from Www.Somanuals.com. All Manuals Search And Download.
which is undesirable for a large audience.
Preferably, use a screen with black, non-reflecting borders,
which will perfectly frame the projected image.
image. For the true cinema experience best results are
achieved with little or no ambient light.
Furniture and other objects with reflecting surfaces, as well as
light coloured walls should be avoided, as they are likely to
interfere with the screen’s characteristics.
Avoid light shining directly on the screen during projection as
this will reduce contrast and black level detail on the projected
5 SWITCHING ON AND OFF THE PROJECTOR
CAUTION: Connect the projector to a power supply
with a nominal voltage within the following values:
SWITCH ON FROM STAND-BY
100-240 Vac, 50/60 Hz. It must be earthed (Fig. 13).
By remote control: press one of 1...9
By keyboard: press Up or Down Arrow .
Position I : on
Position O : off
Power switch
Fused power
socket
H
GRAP
4
ZOOM
R
COOL
(
1
Power plug
F1
Fig. 13
E
Upon switch on (in position I) the projector will initialise (red
and green LEDs on). Followed by stand-by mode (red LED on)
(Fig. 14).
Fig. 15
When switching on from stand-by, the projector will turn on the
lamp; after a brief warm up period the image will be displayed
(green LED on).The input automatically selected will be the
last one memorised prior to switch off (Fig. 15).
You may experience difficulties switching on the projector shortly
after switching off: the lamp may fail to come on as it is too hot.
Just wait a few minutes to cool it down.
pour ne pas compromettre
le de meme type
TTENTION:
A
la protection contre leisstirq
e
ue
s
que d'incende
acter
remplacer par un fusib
ued protection against
et de mems car
or contin
f
UTION:
isk of fire
CA
,
replace
r
R/Cr
G/Y
.
only with same type
ting fuse
a
r
and
UDIO
A
L
A
OUT
DIGIT
5
3
INPUT
GRAPHICS RGB
OM
4
O
2
B/Cb
CONTROL (RS 232)
HV
Fig. 14
9
Download from Www.Somanuals.com. All Manuals Search And Download.
this period.
SWITCHING OFF AND RETURNING TO STAND-BY
Be sure to keep power to the projector onwhen the unit is turned
off to insure that the cooling fans function properly
By remote control: press
By keyboard: press key
LED INDICATORS
When switching off, the projector goes in to stand-by
memorising the input selection at the time of switch-off.
The fans will continue to work until the lamp has cooled down
(red and green LEDs flashing) and will stop automatically after
The LED indicators, located in the top-rear of the projector,
provide information about the state of the projector (see table
below).
INDICATORS
STATE
NOTES
GREEN
RED
POWER OFF
OFF
ON
OFF
ON
The Power is turned off
INITIALIZATION
Power button has been pressed and the software is initialized (15 s)
Projector is in standby mode
STANDBY
OFF
ON
ON
OFF
OPERATING
COOLING LAMP
WARNING
Projector is on
FLASHING
FLASHING
OFF
FLASHING
OFF
Projector is powering down; the fans are running to cool the lamp (1 min)
Problems to display one or more source
Internal circuit failure
ERROR
FLASHING
6 CONNECTIONS
To obtain the best performance from your projector, we
recommend the use of good quality “video cables” to the various
signal sources (75 ohm Impedance).
un
protec
r
tique
is
ainst
la
remplacer pa
et de mems car
acter
ued protection ag
or contin
f
UTION:
risk of fire
CA
,
replace
R/Cr
G/Y
.
only with same type
ting fuse
a
r
and
UDIO
A
OUT
AL
DIGIT
5
3
INPUT
GRAPHICS RGB
4
ZOOM
2
B
Poor quality cables will cause inferior picture performance.
CONTROL (RS 232)
1
HV
For optimum connectivity we recommend you follow these
simple steps:
75
-
With exception of coaxial RCA/Phono type connectors,
always double-check that the plug is inserted the correct
way round to avoid damaging the plugs or the sockets on
the projector (Fig. 16).
Fig. 16
-
Remove cables by the plug and do not pull on the cable
itself.
-
-
Avoid tangled cables.
Position the cables carefully to avoid a trip hazard - especially
in low light areas.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
(Fig. 19). This input accepts a Horizontal Scan Frequency of
between 15-80 kHz and a Vertical frequency of between 48-
100 Hz. Computer Resolutions of VGA, SVGA, XGA, SXGA and
UXGA can be displayed.
COMPOSITE VIDEO INPUT
b
B/C
2
CONTROL (RS 232)
1
HV
UTIO
CA
eplace
.
,
r
isk of fire
r
R/Cr
only with same type
ating fuse
and
r
O
I
D
AU
OUT
AL
DIGIT
5
G/Y
3
INPUT
GRAPHICS RGB
4
ZOOM
B/Cb
TROL (RS 232)
1
HV
CVBS
COMPOSITE VIDEO
Fig. 17
This input is suitable for a “Composite Video CVBS” via a cable
with an RCA/Phono connector (Fig. 17).
Fig. 19
S-VIDEO INPUT
RGB/YCRCB INPUT
B/Cb
A
us
tectio
n
e
inst
la pro
istiqu
2
acter
remplacer par u
et de mems car
ued protection aga
CONTROL (RS 232)
1
or contin
f
UTION:
CA
, replace
fre
.
HV
R/Cr
onlsame type
afuse
and r
UDIO
A
AL
OUT
DIG
5
G/Y
3
HICS RGB
INPUT
B/Cb
RS 232)
(
HV
S-VIDEO
RGSB - YS
CRCB
COMPONENT
VIDEO
Fig. 18
This input is suitable for equipment fitted with a S-Video output
to give improved picture performance (S-VIDEO/S-VHS)
Connection is made via a 4-pin mini-DIN (Fig. 18).
Fig. 20
This input is suitable for a RGB video signal, or for a Component
(YCrCb) type, with composite synchronisation on the green
signal (RGsB) or on the luminance (Y) signal (YsCrCb) through
a cable with RCA/Phono type connector (Fig. 20).
VGA INPUT
Personal Computers, Video Processors (scalers) and Video
Game consoles can be connected to the projector via the HDB
15-Pin (VGA) terminal.
Ensure the output of equipment connected is RGB with one of
the following synchronisation options: separate H/V Sync, H+V
Composite Sync, (RGsB) composite sync on the green signal
RGB or YCrCb signals can also have H+V Composite Sync.
In this case connect the R, G, B (or Y, Cr, Cb) outputs of the
source to the respective R/Cr, G/Y, B/Cb inputs of the projector
(paying attention not to invert the positions) and the synchroni-
sation signal to the HV input . When connecting the three sets
of RCA connectors use the colours as a guide: connector R is
11
Download from Www.Somanuals.com. All Manuals Search And Download.
UTIO
CA
eplace
.
,
r
isk of fire
r
R/Cr
G/Y
red, G is green, B is blue and HV is white. By using a suitable
SCART to RCA connector adapter cable, an RGB video signal
from a source equipped with an SCART connector can be con-
nected to this input.
only with same type
ating fuse
r
and
O
I
D
AU
OUT
L
A
DIGIT
5
3
INPUT
GRAPHICS RGB
4
ZOOM
2
B/Cb
CONTROL (RS 232)
1
Component signals are connected to inputs Y, Cr and Cb, tak-
ing care to observe the correspondence with the outputs on
the source. The video signals that can be connected to this
input can have horizontal scanning frequencies of 15 kHz
(standard video resolution), 32 kHz, or higher (progressive scan-
ning video, high definition video).
HV
Some sources provide the facility to choose between a pro-
gressive signal or an interlaced signal. Although in general a
progressive signal is higher quality than an interlaced signal, it
is often preferable to perform the deinterlacing operation on
the projector rather than on the source because the projector
is equipped with Faroudja’s sophisticated directional correla-
tion deinterlacing technology (DCDi™).
Fig. 21b
MOTORISED PROJECTION SCREEN OUTPUT
4
ZOO
2
DIGITAL INPUT
CONTROL (RS 232)
1
The Digital Input allows to extend the signal quality to audio
signal as well.
Through this input it is possible to connect to source capable
of delivering excellent digital images supported by multi-
channel digital audio and by control data (Fig. 21a).
The internal data elaboration by the projector divides the video
data from audio data.
The audio data is available through a TOSLINK connector for
fiber optic output (Fig. 21b).
Fig. 22
UTIO
CA
eplace
.
,
r
isk of fire
r
R/Cr
G/Y
The projector is equipped with two outputs (Voltage: 12 Vdc)
for motorised projection screen and screen masking systems.
These 12V outputs should be connected to the appropriate
screen interface provided by the screen manufacturer (Fig. 22).
only with same type
ating fuse
r
and
O
I
D
AU
OUT
AL
DIGIT
5
3
INPUT
GRAPHICS RGB
4
ZOOM
2
B/Cb
CONTROL (RS 232)
1
HV
The +12V output is activated when the projector is switched on
(green LED on) and is de-activated when the projector is in
stand-by mode (red LED on).
The output
can be used to control a screen masking system;
its output can be set with the “Screen control” adjustment in
the “Aspect” menu. This output allows reduction in the area of
a 16:9 screen, into a 4:3 format, by activating a screen masking
system (refer to screen manufacturer for further information).
Fig. 21a
12
Download from Www.Somanuals.com. All Manuals Search And Download.
RS232 INTERFACE CONNECTOR
UTIO
CA
eplace
.
,
r
sk of fire
i
r
R/Cr
G/Y
only with same type
ating fuse
and
r
UDIO
A
OUT
It is possible to control the projector through a personal com-
puter. First, load the appropriate projector control software onto
your PC, then simply connect this input to a cable from your
PC’s RS232 serial port (Fig. 23).
AL
DIGIT
5
3
INPUT
GRAPHICS RGB
4
ZOOM
B/Cb
ROL (RS 232)
1
HV
Fig. 23
7 KEYBOARD PAD
Eight push buttons, at the rear of the projector, will allow com-
plete operation without the use of the remote control.
Menu
Switches off to stand-by.
Activates the On Screen Display menus. Navigates
Menu pages.
Auto
Selects Auto Adjust
(automatic optimisation of the
displayed image).
-Focus-Esc
Up/Down/Left/Right arrow keys
De-activates the On Screen Display and
gives access to the lens Zoom/Focus
adjustment functions.
Navigate through and make adjustments to the
On Screen menus.
Arrow Up/Down switch on from stand-by and
recall Source Selection menu.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
8 REMOTE CONTROL
Insert the batteries, taking care to match the polarity, as
indicated in the battery recess of the remote (Fig. 24).
The remote control sends commands to the projector via
infrared signals.
It is possible to control the projector by pointing the remote
control at the screen; the sensor at the front of the projector will
pick up the reflected infrared commands. (Fig. 25).
-
+
+
-
-
four 1.5V
+
AAA alkaline
batteries
+
-
:
p
u
n
r
n
l
r
e
d
co
ue
m
m
e
pr
i
c
ende
t
re
A
p
r
o
t
c
I
c
i
n
a
r
u
e
n
g
i
st
erl
e
de
T
I
s
o
c
c
o
al
p
r
o
t
t
a
c
i
t
R
/
C
r
Cr
i
o
A
l
of
ti
i
i
g
s
ame
s
e
.
t
p
and
y
r
A
U
D
IO
IT
A
O
U
T
I
C
S
2
R
3
G
B
G
/
Y
3
5
DIG
IN
P
U
T
L
Z
O
2
O
M
4
G
RA
PH
B
/
C
(
R
S
2
)
1
C
O
H
V
LIGHT
Fig. 24
Z
O
O
F
M
1
Change the batteries in the remote control if experiencing
difficulty in sending commands to the projector.
If the remote control is not to be used for a long period of time
remove the batteries. Replace all batteries at the same time;
do not replace one new battery with a used battery. If the
batteries have leaked, carefully wipe the case clean and replace
with new batteries.
Fig. 25
Avoid placing obstructions between the remote control and the
infrared sensor at the front of the projector; this will impair the
remote control performance.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
9 ON SCREEN MENU
in the box additional information is displayed concerning the
video standard (for video signals) or resolution (for graphic
signals), and format.
Fom the SETUP menu it is possible to choose to visualize or not
this information, for more details check the “SOURCE
INFORMATION” in “MENU” section.
SOURCE SELECTION
The input selection menu (Inputs) is called by pressing 0 on
the remote control and, when no other menu is displayed, using
the ꢀ and ꢁ keys on the keypad. To select an input, scroll the
list with the ꢀ and ꢁ keys until the desired input is highlighted,
then press ꢂ.
Display of the input selection menu is terminated by pressing
the ESC key, or when the time allowed for displaying the on-
screen menu has lapsed (set in the Set-up Menu).
MAIN MENU
Input 3 can receive RGB and YCrCb signals, at 15 kHz, 32 kHz
or higher. The association between the input and the type of
signal is made from the pull-down menu that appears on the
right of the < symbol after pressing the ꢃ key (Fig. 26b).
To access the main menu of the On Screen Display press the
MENU key on the keypad or the MENU+ or MENU- key on the re-
mote control.
The main menu is divided into four windows, PICTURE,
IMAGE, SETUP and MENU, in which the various adjustments are
grouped according to the frequency of use. Use ꢀ and ꢁ
to select the line corresponding to the adjustment you wish to
make (Fig. 27).
Inputs
1
2
3
4
5
VIDEO
S-VIDEO
COMPONENT/RGBS
GRAPHICS RGB
DIGITAL INPUT
1
2
3
4
5
15kHz
RGBS
Picture
Brightness
60
Contrast
Color
Tint
Sharpness
Filter
50
50
50
3
Fig. 26a
Inputs
2
Cinema Mode
Off
Normal VCR1 VCR2
Auto
Auto
1
2
3
4
5
VIDEO
S-VIDEO
COMPONENT/RGBS
GRAPHICS RGB
DIGITAL INPUT
1
2
Video Type
Noise Reduction
Fig. 27
RGBS
RGBS 15kHz
YCrCb 15kHz
YCrCb
The various menus only offer the relevant adjustments in
accordance with the type of input signal displayed (e.g. certain
typical adjustments for video signals, not necessary for graphic
signals, do not appear on the menus, and vice versa).
Some adjustments (e.g. BRIGHTNESS and CONTRAST) are
associated with a numerical value that can be varied within the
set limits using the keys ꢃ / ꢂ. For others (e.g. VIDEO TYPE) you
can choose among three options presented on the same
ꢃ / ꢂ).
Fig. 26b
After selecting the source signal (by means of the ꢀ and ꢁ
keys), press MENU+/MENU - to confirm and close the pull-
down menu; the value you have just set will be displayed on
the right of the < symbol.
As with the other inputs, you can now select the input just set
by pressing the ꢂ key.
During the short time it takes to find the signal, a box appears
showing the signal requested. As soon as the signal is shown
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Other adjustments (marked by the < symbol) provide
submenus, which appear as a superimposed window in which
the selection is made with the ꢀ / ꢁkeys (Fig. 28). .
CONTRAST
Use this control to adjust the image’s black level without
affecting white areas.
To ensure correct adjustment, it may prove useful to display
the signal relative to the grey scale, within which the white level
and the level immediately below it must be separately
identifiable. Alternatively use a scene composed of well-lit white
objects surrounded by light coloured objects with lower level
lighting.
Image
Aspect
Color Temperature
Gamma Correction
Overscan
Position
Y/C Delay
1
1
COLOR
This control (also called Saturation) increases or decreases
the picture colour intensity. When set to zero, colour images
will be shown in black and white. Increasing the value, try to
find the point at which the colours look natural: suitable
references include skin tones and grass in landscape shots.
Fig. 28a
Image
Normal
Aspect
Anamorphic
Letterbox
Panoramic
Pixel to pixel
User 1
Color Temperature
Gamma Correction
Overscan
Position
Y/C Delay
TINT
Controls the purity of the colours. Basically determines the
red-green ratio of the picture.
Reducing the value will boost the red contents of the picture,
increasing the value will boost the green tones. For this
adjustment use skin tones or a test pattern image with colour
bars as a reference.
User 2
User 3
Fig. 28b
SHARPNESS
These submenus are accessed by pressing the ꢃ key, while
exit and return to the upper level occurs by pressing MENU+/-
Press ESC on the remote control or keypad to interrupt the
menu display or wait for it to disappear automatically after the
number of seconds set on the SETUP page.
Use this adjustment to increase and decrease the level of
picture detail.
.
When the sharpness value is reduced the image details
appear less pronounced, while increasing the value raises
image definition, making the outline of objects sharper.
Note that an excessively high value may result in a ‘noisy’ picture
and the edges of objects may be unnaturally defined.
PICTURE
This menu features the adjustments related to picture quality.
Adjustments that are not available for a given input do not
appear on the menu. Table 1 summarises the adjustments
available for each input. For a complete overview of the on-
screen menus, consult the ‘On screen menu layout’ in the
“Additional Information” section.
SHARPNESS MODE
This allows you to select the type of processing associated
with sharpness adjustment. In the case of a progressive or
interlaced video signal VIDEO mode is advisable; with PC graphic
signals use GRAPHIC MODE
.
BRIGHTNESS
FILTER
Use this control to adjust the image’s black level without
affecting white areas. Increasing the value will give more detail
in darker parts of the picture. For correct adjustment it may
prove useful to display the signal relative to the grey scale within
which the black level and the level immediately above it must
be separately identifiable. Alternatively use a scene composed
of black objects alongside other dark coloured objects.
This allows you to select the mode in which the input signal
is processed. Selecting the most appropriate value for a given
input signal ensures the best horizontal and vertical definition
and makes the picture sharper.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CINEMA MODE
In the left side the image is not altered by the filter, in the right
part the filter is activated.
This allows you to compare the effect of the filter.
It is possible to deactivated the filter (NOT ACTIVE), to use the
In AUTO the deinterlacer recognises if the video signal source
is a movie film (obtained from a Telecine device with 3:2 or 2:2
pull-down) and applies a deinterlace algorithm optimised for this
type of signal.
If the video signal source is not identified as a film, or if you
select NO the deinterlacer applies a Motion compensated
algorithm optimised for video camera signals.
automatic adjustments (AUTO) or to manually select (MANUAL
)
the value suitable for the image with the VALUE adjustment.
In case of using the VALUE adjustement, it is enoght to select to
cursor below and set the value with the ꢃ / ꢂkeys of the remote
control.
Associated to the NOISE REDUCTION there is the possibility to use the
specific function (FLESH TONE CORRECTION) to make skin tone more
natural. Often the use of noise reduction filter slightly degrades
the image in those areas where skin tones are visible. With the
use of this function it is possible to maintain an excellent image
quality throughout the entire projected image.
VIDEO TYPE
Activates a filter to improve stability of pictures from video
recorders. To toggle between NORMAL, VCR1 mode and VCR2
mode press
on the remote control.
NOISE REDUCTION
This adjustments allows to choose the filter value for noise
reduction purposes.
As soon as this option is selected on the menu, the image is
divided in two parts.
TABLE 1INPUT SIGNALS AND ADJUSTABLE/SETTING ITEMS
INPUTS
Video
S-Video
RGBS 15kHz
YCrCb 15kHz
ADJUSTEMENTS
RGBS
YCrCb
RGB Grafico
DIGITAL INPUT
BRIGHTNESS
CONTRAST
COLOR
-
-
-
-
-
-
(NTSC)
TINT
SHARPNESS
-
-
SHARPNESS MODE
FILTER
-
-
-
-
-
CINEMA MODE
VIDEO TYPE
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
NOISE REDUCTION
FLESH TONE CORRECTION
Adjustable/can be set
Not adjustable/can not be set
-
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SCREEN CONTROL
IMAGE
For each aspect chosen, the SCREEN CONTROL command
allows you to reframe the screen to a variety of aspect ratios
and screen size, using an appropriate screen-masking inter-
face connected to the 12 V output socket (please refer to the
screen manufacture's manual)
This menu features adjustments relating to picture position,
aspect ratio, etc.
ASPECT
This adjustment allows you to change the dimensions and
aspect ratio (relationship between width and height) of the
displayed image. There are five preset aspects available and
three personalised aspects (with user-settable parameters). You
can select a different aspect for each source: the selected
aspect ratio will be automatically called the next time the rela-
tive source is called.
COLOR TEMPERATURE
Changes the colour balance of the image.
Colours can be adjusted towards the red end of the spectrum
(low colour temperature values - expressed in degrees Kelvin)
or the blue end (high values).
Colour temperature can be selected with three preset values:
HIGH (corresponding to approx. 9000 degrees Kelvin), MEDIUM
(approx. 8000 degrees Kelvin), LOW (approx. 6500 degrees
Kelvin) and one PERSONAL setting controlled by the user with
You can also select the required aspect ratio by repeatedly
pressing the
(1...8).
key, or by pressing
and a numerical key
The following aspects are available.
separate adjustments for RED, GREEN and BLUE
.
In the personale color adjustment for all three colors it is possible
to set an Offset value and Gain.
The Offset adjustments have an impact of the low IRE values,
while the Gain adjustments impact of the higher IRE values.
Generally, the HIGH value is more suitable for displaying graphic
images, MEDIUM and LOW for video images.
NORMAL: projects the image occupying the full height of the
screen while maintaining the aspect ratio of the input signal.
When the input signal aspect ratio is 4:3 black vertical bands
are displayed on the right and left of the picture.
ANAMORPHIC: allows a 16:9 picture to be displayed correctly.
These adjustments are reserved for expert users since there is
a risk of obtaining results that impair projected image quality.
LETTERBOX: serves to display 4:3 letterbox image (with source
signal having black bands above and below the picture) so
that it fills the 16:9 screen and maintains the correct aspect
ratio.
GAMMA CORRECTION
Determines the system’s response to the grey scale,
emphasising or attenuating the different grades of brightness
(blacks, dark, medium, light grey, whites) in the projected
image.
The GRAPHICS setting is more suitable for computer images,
while the FILM and VIDEO settings are more suitable for video
images.
PANORAMIC: this aspect stretches the 4:3 image, slightly
cropping the upper and lower parts.
Panoramic is ideal for displaying a 4:3 image on the 16:9 screen
of the Display.
PIXEL TO PIXEL: this aspect displays the image as it is input without
adapting it to the screen.
The image is projected in the centre of the screen and if its
horizontal and/or vertical dimensions are smaller than the
display, it is bounded by vertical and/or horizontal black bands.
OVERSCAN
Remove noise around image. Some sources can produce a
picture with noise along edges, thanks to the overscan function
it is possible to drop such imperfections outside the projected
area. The overscan value can be included between 0 (no
overscan) and 32 (maximum value). The image maintains in
any case the aspect.
USER 1, 2, 3: When none of the preset formulas are suitable, the
User formulas are available, with the facility for continuous
horizontal and vertical adjustment of picture size.
POSITION
Use this adjustment to position the image vertically and
horizontally. Determines the aspect ratio of the projected image.
These parameters do not normally require adjustment because
the system checks the input signal and automatically sets the
18
Download from Www.Somanuals.com. All Manuals Search And Download.
most suitable values.
the system to repeat the input signal analysis and determination
of the best parameters by calling the automatic adjustment
procedure with the AUTO key on the remote control or on the
keypad.
If the automatic procedure fails to have the required effect, enter
the frequency and phase values manually and approach the
screen sufficiently to observe the effects of the adjustments.
However, if the image is not perfectly centralised it may prove
useful to request the system to repeat the input signal analysis
and image positioning, calling the automatic control procedu-
re from the AUTO button on the remote control or keypad. When
this procedure is called it is helpful to have a white or light
coloured background on the screen in the current picture.
FREQUENCY/PHASE
Y / C DELAY
These adjustments, available for progressive signals and for
signals from PC, ensure correspondence between the number
of pixels making up the signal and the number of pixels making
up the projected image.
These parameters do not normally require adjustment because
the system checks the input signal and automatically sets the
most suitable values.
In the case of Video and S-Video signals, it may be necessary
to correct horizontal colour misalignment within the projected
image. For a given video standard (e.g. PAL or NTSC) the stored
value does not normally require further fine-tuning, unless the
source or connection cable has changed.
However, if the image appears disturbed (loss of position within
the equidistant vertical bands or instability and lack of
sharpness on the narrow vertical lines) it may help to prompt
TABLE 2 INPUT SIGNALS AND ADJUSTABLE/SETTING ITEMS
INPUTS
Video
S-Video
RGBS 15kHz
YCrCb 15kHz
ADJUSTEMENTS
RGBS
YCrCb
Graphic RGB
DIGITAL INPUT
-
POSITION
ASPECT
-
-
FREQUENCY
PHASE
-
-
-
-
COLOR TEMPERATURE
GAMMA CORRECTION
OVERSCAN
-
Y/C DELAY
-
-
-
-
Adjustable/can be set
Not adjustable/can not be set
19
Download from Www.Somanuals.com. All Manuals Search And Download.
If the projected images needs to be centred horizontally, the
manual lens shift adjustment allows the projected image to be
moved vertically, up or down, in relation to the centre of the
screen; the maximum adjustment being equal to half the height
of the image in either direction (Fig. 31).
SETUP
The setup menu contains less frequently used adjustments that
may be required during installation (e.g. On Screen Display
language selection or the display of Test Patterns).
ORIENTATION
Select the option that best describes the installation i.e. desktop
front, ceiling front, desktop rear and ceiling rear.
p
r
o
m
c
e
e
t
tre
e
l
re
c
s
o
m
e
d
'
i
n
t
y
p
n
e
de
:
p
c
our
t
r
e
n
pas
s
e
TTE
N
o
TION
n
o
u
n
n
f
u
s
i
b
l
e
d
A
ue
inst
ection aga
l
a
p
r
l
a
c
e
r
p
a
r
a
a
c
t
e
r
i
s
t
i
q
rem
e
mems
c
n
u
e
d
p
r
o
t
et
CA
d
f
o
r
c
o
n
t
i
U
TfIOfi
re
N
,
rep
la
e
ty
c
e
R
/
C
r
r
i
s
k
y
o
w
i
t
h
s
a
m
s
e
.
on rating fu
and
A
UDI
O
OUT
AL
G
B
G
/
Y
3
5
DIGIT
T
INPU
A
P
H
I
C
S
S
2
R
O
M
4
G
R
Z
O
2
B
/
C
b
)
O
L
(
R
3
2
1
C
O
NT
R
H
V
Fig. 31
tre
m
p
r
omet
c
e
n
d
e
o
n
d
'
u
r
n
e
pas
r
e
s
c
q
u
e
i
N
:
p
o
t
r
e
l
e
s
e
mem
typ
e
N
T
I
O
c
o
n
l
e
d
e
TTEtection
fusib
A
n
e
st
tion again
l
a
p
r
o
a
c
e
r
p
a
r
u
cteristiqu
e
m
p
l
e
m
s
cara
rotec
r
m
ed
p
t
d
e
r
c
o
n
t
i
n
u
e
f
o
:
ce
TION repla
type
risk of same
CA
U
fire,
/
r
R
C
with
r
.
only ting fuse
a
and
IO
UD
A
A
L
T
OU
IT
B
G
/
S
2
R
G
Y
3
5
IG
I
C
UT
N
P
H
M
4
G
R
A
ZOO
2
B
/
C
b
3
2
)
(
R
S
L
T
R
O
1
C
O
N
H
V
In the event you are unable to centre the image within the screen
area, tilt the projector until the image is correctly positioned.
Any keystone error can be removed by the Keystone adjustment
in the Set up menu.
Fig. 29
The keystone adjustement helps to compensate possible
horizontal tilts of the projector.
HORIZONTAL/VERTICAL KEYSTONE
To obtain maximum quality of the projected image, we
recommend the installation of the projector on a level platform
parallel and central to the screen.
Adjust the feet underneath to obtain a level position, lining up
the base of the projected image to the base of the projection
screen (Fig. 30).
LENS
The Zoom adjustment impacts on the motorized zoom lens
allowing to increase or decrease the dimension of the projected
image. The Focus adjustment impacts on the motorized lens
focus, allowing to obtain the highest definition on the projected
image, an accurate focus setting should allow the viewer to
distinguish each pixel that create the image one from another.
FOCUS
FOCUS
FOCUS
FOCUS
romettre
p
o
u
r
n
e
p
a
s
c
o
m
p
A
TTENTION
la protectio
remplacer pa
et de memso
n
:
c
o
n
t
r
e
l
e
i
b
s
lere
d
s
e
qu
m
e
e
d
m
'i
e
n
e
r
un
f
u
s
ristique
a
g
a
i
n
s
t
a
c
t
e
tect
i
o
n
d
p
r
o
u
e
c
r
a
crontin
:
f
e
T
I
O
N
e
p
l
a
c
CA
U
,
r
e
k
o
f
f
i
r
e
a
m
e
t
y
p
R/Cr
G/Y
ris
ith
s
w
r
se
.
only ting fu
a
and
A
UDIO
OUT
AL
DIGIT
INPU
5
3
T
OM
4
G
R
A
P
H
I
C
S
R
G
B
ZO
2
B/Cb
1
C
O
N
T
R
O
L
(
R
S
2
3
2
)
HV
re
omettde
r
n
e
pas
r
e
s
c
q
ompr ncen
typ
e
u
e
d
'
i
N
:
p
o
u
t
r
e
l
e
s
e
mem
TTEtectio
NTIO
n
con
fusib
l
e
d
e
A
n
e
st
l
a
p
r
o
c
e
r
p
a
r
u
a
c
t
e
r
i
s
t
i
q
u
t
i
o
n
a
g
a
i
n
e
m
p
la
e
m
s
f
car
rotec
r
m
ed
p
t
d
e
r
c
o
n
t
i
n
u
e
o
I
O
N
:
e
p
l
a
ce
T
r
CA
U
f
fire,
type
same
with .
only ting fuse
a
o
R
/
C
r
risk
and
r
A
UD
IO
OU
ITAL
G
T
I
T
G
B
G
/
Y
5
I
C
S
2
R
3
P
H
M
4
G
R
A
ZOO
2
B
/
C
b
3
2
)
(
R
S
L
T
R
O
1
C
O
N
H
V
Fig. 30
Fig. 32
20
Download from Www.Somanuals.com. All Manuals Search And Download.
In the initial phase of installation the configurable keys (F1, F2)
serve as optical zoom and optical focus (Fig.32).
33).
The exclusion or activation of the source will automatically
renumber the remaining active inputs.
POWER ON
If active (AUTO) allows to power up the system directly from the
power feeder, once the initializing phase is completed.
If not active (STAND-BY) once the initializing phase is completed
the system remains in a stand-by mode waiting to receive the
power on command from the remote control or the key pad.
Source list/Edit source name
1
1 VIDEO
VIDEO 1
2
2 S-VIDEO
ACTIVE
Yes
No
3
3 COMP / RGB
4 GRAPHICS RGB
5 DIGITAL INPUT
NAME
4
5
DIGITAL INPUT 5
TEST PATTERNS
Displays a series of five test patterns, useful for the installation
of the projector.
Press ꢁ and ꢀ keys to browse pattern.
Fig. 33
The inputs with an active video signal (visible in the input
selection menu) are marked with a check symbol.
It can be also helpful to identify the input with a name chosen
by the user (for example with the name of the connected source)
rather than with the signal type.
Once chosen to have the input visible, in the drop menu, by
selecting the Name option it is possible to rename the source
in use.
This will make it easier to remember the source connected to a
specific input. You can use up to 12 alphanumeric letters to
name the source (for more details check the “Insert text” section)
FACTORY DEFAULTS
Reconfigures the projector to original factory settings except
Position, Orientation, Y/C Delay, Zoom and Focus.
Insert text
You will be able to insert text easily and rapidly by accessing
the text insertion menu (fig. 34)
Confirm?
No
Yes
MENU
LANGUAGE
Lists the languages available for the On Screen Display menus.
SOURCE LIST
In order for projector to be more flexible, the following described
functions allow to modify the input selection menu making it
more user friendly.
The main window shows all the inputs available on the projector.
If one or more inputs are not utilized, it is often helpful to blank
them from the input list (accessed with the 0 key).
Once the input has been chosen, in the drop menu that appears
by pressing the ꢃ key, it is possible to activate the source (Fig.
Fig.34
21
Download from Www.Somanuals.com. All Manuals Search And Download.
The text insertion mode remains the same if text is being inserted
for the first time or if a previously inserted name is being edited.
The letter insertion can be done in any available position
(represented by horizontal lines).
Zoom
Allows to access the optic zoom, where the ꢃ and ꢂ keys
allow to increase or decrease the size of the projected image.
Use the ꢂ and ꢃ keys to move between letters either left or
right respectively.
Focus
Once selected, the ꢃ and ꢂ keys allow to focus the image.
Press the numeric key matching the letter (Fig. 34), the first
click of the key selects the first letter, the second click the
second letter and so on.
The available letters are shown in the text insertion menu.
Once one letter has been inserted, to insert the following one it
is necessary to move with the cursor in the next right position
with the ꢂ key of the remote control, repeat this procedure to
insert other letters.
Use the ꢀ key to switch from small case to capital letters and
viceversa.
Any mistake can be deleted with the ꢁ key once it has been
positioned on the wrong letter.
Magnification
Allows you to select the area to be viewed and then magnify
the projected image. The degree of enlargement is selected in
Zoom mode (identified by a magnifying glass in the centre of
the image) using the ꢃ and ꢂ keys. The area of the picture to
be enlarged is selected in Pan mode (symbol in the centre of
the picture) using the ꢀ and ꢃ, ꢂ arrow keys. You can
toggle between Zoom and Pan mode by pressing the F1/F2
key on the remote control.
Blank
Once the text insertion process is finished, it can be confirmed
and saved by clicking the MENU+ key.
If you want to delete the modifications use the MENU- key of the
remote control.
Blanks the active video signal producing a completely black
screen. Once pressed the key an indication of a few seconds
on the OSD will confirm its activation. A click of any other key
of the remote control allows to restore the previous settings.
F1/F2 KEYS
Color temperature
The following click of the key (F1 or F2) allows to choose between
the different color temperatures available. High, Mid, Low, User.
This allows to assign different functions to the remote control
keys, named F1 and F2.
The window is made of 6 options, once for each line and bytwo
columns showing the F1-F2 keys. The choice between F1 and
F2 is made by the ꢂ and ꢃ keys of the remote control; the
function given to F1 and F2 is chosen with the ꢀ and ꢁ keys.
The function delivered by the key is memorized by the
intersection on the line and column.
Gamma correction
The following click of the key (F1 or F2) allows to choose
between the different gamma curves available.
SOURCE INFORMATION
When active (YES) each source change will show the information
related to the signal. If not active (NO) there will be no information
on the selected source.
In the following window are described the 6 options
Menu
OSD BACKGROUND
Language
Source list
F1/F2 keys
Source info
OSD Backgro
OSD Position
OSD Timeout
English
Determines the type of background for the On Screen Display.
F1 F2
OSD TIMEOUT
Zoom
Focus
Magnification
Use this adjustment to set the display time after which the On
Screen Display will disappear.
Blank
Color temperature
Gamma correction
OSD POSITION
Allows the On Screen Display to be positioned in a particular
area of the projected image. The OSD can be positioned using
the arrow keys for fine adjustments or keys 1...9 on the remote
control to select one of 9 preset positions.
Fig.35
22
Download from Www.Somanuals.com. All Manuals Search And Download.
The operations that can be performed on each memory se-
lected are described here below.
MEMORIES
The main parameters of the image may be saved in distinct
groups of values (known as ‘Memories’); these parameters can
subsequently be applied all together by way of a single com-
mand.
There are 3 distinct Memories (Memory 1, Memory 2, Memory
3) for each of the 8 signal types managed:
SAVE A MEMORY
To save the current values of the image parameters in Memory
1, use the ꢀ and ꢁ keys to move to line ‘1’ and then open the
pull-down menu by pressing the ꢃ key (Fig.37). Then select
the option ‘Save current settings’. To confirm that the operation
has been completed successfully, the message ‘Current set-
tings saved in Memory 1’ is displayed at the bottom of the screen
and the letter ‘S’ appears to the left of the memory name. The
same procedure is used to save parameters in Memories 2
and 3.
1 VIDEO
2 S-VIDEO
3 COMP/RGB(YCrCb 15KHz)
3 COMP/RGB(YCrCb)
3 COMP/RGB(RGB 15KHz)
3 COMP/RGB(RGB)
4 GRAPHICS RGB
Memories
5 DIGITAL INPUT
0 Auto
1
2
3
S
Save current settings
Save initial settings
Rename
making a total of 24 different available Memories.
The image parameters that can be saved/recalled by the Memo-
ries management system are the following:
I
S
Image
Picture
BRIGHTNESS
CONTRAST
COLOR
ASPECT
COLOR TEMP. GAIN (R/G/B)
COLOR TEMP. GAIN OFFSET (R/G/B)
COLOR TEMP.
Fig.37
TINT
RECALL A MEMORY
SHARPNESS
FILTER
SHARPNESS MODE
VIDEO TYPE
NOISE REDUCTION
OVERSCAN
To recall a Memory, select the desired line and press ꢂ. The
parameters saved in the selected Memory will be applied to
the image displayed and a message will appear to confirm the
operation ‘Memory 1 recalled’. The Memory recalled will be
associated with the source and signal type, and will be auto-
matically recalled every time that particular source and signal
type combination is selected.
GAMMA
Some of these parameters may not be available for certain in-
puts or certain input signals, as indicated in Tables 1 and 2.
The menu page for the Memories management functions is
activated by pressing the
ꢃ key on the keypad (Fig.36).
SAVE DEFAULT SETTINGS
key on the remote control or the
To restore the original values to a previously modified Memory,
select the line corresponding to the Memory in question and
open the pull-down menu ( ꢃ key). Then select the line “Save
default settings”. To confirm that the operation has been com-
pleted successfully, the message ‘Initial settings saved in
Memory 1’ is displayed at the bottom of the screen and the
letter ‘I’ appears to the left of the name of the memory.
RENAME A MEMORY
H
GRAP
4
ZOOM
2
It is possible to assign a name to each Memory. To assign a
name (with a maximum length of 12 alphanumeric characters)
to a Memory, select the option ‘Rename’ from the correspond-
ing pull-down menu. Enter the text following the procedure in-
dicated in paragraph “SOURCE LIST”.
R
CONTROL
(
Fig.36
23
Download from Www.Somanuals.com. All Manuals Search And Download.
RESTORE CURRENT SETTINGS
QUICK MENUS
On entering the ‘Memories’ menu, a copy of the current set-
tings is saved in a temporary menu (labelled with 0 - AUTO).
Once one or more memories have been recalled, you can re-
store the settings that were effective at the moment the Memo-
ries menu was accessed by selecting 0 - AUTO. However, this
operation must be completed before the ‘Memories’ menu page
disappears (30 seconds after the last operation commanded
from the remote control or the keypad). The next time it ap-
pears, the temporary memory will contain new information that
takes into account any Memories selected the penultimate time
the ‘Memories’ page was accessed.
The Quick menus allows the adjustment of most of the picture
quality controls without recalling the main On Screen menus.
Brightness, Contrast, Color, Tint, Sharpness and Filter
adjustments appear at the bottom of the screen, one after
another, when Up and Down Arrow keys are pressed.
MESSAGES
The following messages could appear on your screen:
Memory 0 (- AUTO) can be used even when you do not wish to
enable the Memories management function for the signal
currently in use. Once Memory 0 has been selected, when a
source is chosen, the settings that were effective at the time
the Memory was previously recalled will be automatically
applied.
No Signal
The projector does not recognise any signal sent through the
selected input.
- Check that the selected input is actually connected to
a video or graphic signal.
INFO
- Verify compatibility of video/graphic signals with technical
specifications of your projector.
- Check the integrity of cables used to connect various
sources.
Displays the current status of the projector and information
concerning the projected video/graphic signal.
This function is displayed on pressing
on the remote control
(or, in the absence of the On Screen Display, the ꢂ key on the
remote control).
Out of range
Either the resolution or the horizontal/vertical frequency of the
input signal is too high.
- Input a signal that is within specifications.
10 CLEANING AND MAINTENANCE
The projector does not require internal cleaning. There are no
user serviceable parts inside the projector. Please refer all
service requirements to qualified personnel.
printing.
Cleaning the lens:
The lens may be cleaned with a very soft, non-abrasive small
brush, in order to remove dust particles. Alternatively, use a
soft dry cleaning cloth (of the type used for camera lens
cleaning) to remove fingerprints and grease marks.
Cleaning the projector’s cover:
Use a soft slightly damp cloth. Do not use abrasive cleaners,
solvents or other harsh chemicals, as this will damage the finish
of the cover. Avoid direct cleaning of the rear panel’s screen-
24
Download from Www.Somanuals.com. All Manuals Search And Download.
11 TROUBLESHOOTING GUIDE
No power (Green and red LED are OFF)
- If the signal source is a terrestrial broadcast (via a VCR) check
that the receiving channel has been correctly tuned in and
that the aerial system is in good working order.
- Should the problem be present with a signal coming from a
video-recorder, ensure that the videotape is an Original “first
generation” copy and in good condition.
- Check the power switch at the rear: it must be in position I.
- Check if the power cable has been connected correctly to a
working socket.
- Check the power socket fuse, at the rear of the projector.
- Replace the fuse on the mains socket with an identical type
(T 3.15A H) (Fig. 2).
- Adjust the VCR’s tracking control for optimum picture perfor-
mance. Ensure the VCR mode is active in the Picture menu.
- Should the problem persist, seek authorised technical
assistance.
Incomplete image along borders (vertical and horizontal)
The lamp is not coming on
- Compare compatibility of video/graphic signals and techni-
cal specifications of your projector.
- Press Auto (on your remote or keypad) to execute automatic
adjustments.
- Adjust the horizontal and vertical position of projected image
by selecting Position on the Image Adjustmentsmenu.
- Adjust the width and height of image, selecting Aspect in
the Image Adjustments menu.
- Allow a few minutes pause between switching off and turning
on again (from stand-by). This will allow the lamp to cool down
sufficiently.
- If the lamp doesn’t come on – even though the projector has
had sufficient time to cool down – seek technical assistance
from your nearest Dealer.
Image too dark, too pale or unnaturally coloured
No image
- Verify compatibility of video/graphic signals with technical
specifications of your projector.
- Check that the selected input is actually connected to a active
video or graphic signal.
- Check that the above source actually works.
- Verify compatibility of video/graphic signals with the technical
specifications of the projector.
- Check the integrity of cables used to connect various sources.
- Check temperature of the room: it must be below 35°C
(95°F)
- Go to Picture menu, select and regulate any of the following,
accordingly: Contrast, Brightness, Color, and Tint.
- If necessary, reset the Color Temperature and Gamma
Correction (found on the Image Adjustments /
Advanced Settings menu).
- Check projector air vents on top and underneath the projector:
they must be free of obstruction.
Graphic image with poor quality vertical detail
- If the problem persists, consult your Dealer.
- Verify compatibility of video/graphic signals with technical
specifications of your projector.
- Press Auto (on your remote or keypad) to execute
Image is disturbed, unstable or noisy
automatic adjustments.
- Verify compatibility of video/graphic signals with the technical
specifications of the projector.
- Check the integrity of cables connecting projector to various
sources.
- Adjust Frequency and Phase parameters, found in the
Image Adjustments menu, to optimise vertical detail of
the projected image.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Image showing colour misalignment on vertical
details
Remote control does not work
- Check the batteries and for correct polarity.
- Verify compatibility of video/graphic signals with technical
specifications of your projector.
- Adjust Y/C Delay settings in the Image Adjustments /
Advanced Settings to reduce colour misalignment. For
best results use an external colour bar test pattern source.
- Ensure that the area between the infrared sensor (front of
projector) and the remote control is free of obstruction.
- Ensure that infrared sensors (front and rear of projector) are
not exposed to intense light levels.
12 OPTIONAL ACCESSORIES
You can purchase the following optional accessories at your
Dealer:
CAUTION: for ceiling/wall installation, by means of
suspension bracket, carefully follow the instructions
and safety instructions recommended by the
Manufacturer in the bracket’s literature.
- Wall/Ceiling Bracket Kit.
Use only original, or Faroudja approved, accessories.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
A TECHNICAL SPECIFICATIONS
OPTICAL
ELECTRICAL
Projection system:
optical engine based on 1 DMD™
Input Signals:
CVBS on RCA/Phono type connector
S-VHS on Mini-DIN connector
RGBHV on DB15HD connector
RGBS / YCrCb on RCA/Phono type
connector
HD2+ chip, sealed housing, dusty proof
DMD™ panel:
resolution 1280x720 pixel
Brightness uniformity:
Contrast ratio:
10% above or below the average
> 2800:1 (full On / full Off)
Digital Input
Horizontal frequency:
from 15 to 80 kHz (up to to UXGA
format @ 60 Hz)
Projection lens:
zoom, 12 elements AR multilayer
coating, motorized focus and zoom,
manual elevation
Vertical frequency:
Video standards :
48-100 Hz
Aperture f#:
Picture size:
Aspect ratio:
2.7 (zoom max) - 3.3 (zoom min)
50-250 inches (diagonal measure)
4/3 and 16/9
automatically selected (PAL B,G,H, I,
M,N,60, SECAM, NTSC 3.58, 4.43)
High definition video:
Graphic standards :
Deinterlacer:
ATSC HDTV (480p, 720p, 1080i)
VGA, SVGA, XGA, SXGA, UXGA
Throw ratio:
(throw distance: picture width)
1.8:1 - 2.5:1
Faroudja chip set, DCDi™, 3:2 pull
down sequence convertion
Focus range:
2.2 - 13.0 m (7’ 3” - 42’ 8”)
Colour temperature:
Video processor:
adjustable from 5000 to 9300 degrees
K
Throw Distance:
60”: 2.4m - 3.3m (7’ 11” - 10’ 10”)
80”: 3.2m - 4.4m (10’ 6” - 14’ 5”)
100”: 4.0m - 5.5m (13’ 2” - 18’ 1”)
DTI, CTI, comb filter, noise reduction.
Sharpness, Y/C delay and NTSC tint
adjustments
Keystone adjustement: up to 26° (optical: 8° digital: 18°)
Lamp:
120 W
Remote control:
via infrared remote control and via
computer through RS232 serial
interface
Lamp life time:
6000 hours (average value measured
in the laboratory under optimal condi-
tions; it can be sensibly reduced by
the unit misusing)
Low Voltage Power Output: two 12 Vdc output, 100 mA max on
jack connectors
27
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL
ENVIROMENTAL
Supply:
from 100 to 240 Vac, -10% +6%
tolerance
Operation temperature:
Transportation temp.:
Storage temperature:
Humidity:
0 to 35°C (32° to 95°F)
-10 to 55°C (14° to 131°F)
-10 to 55°C (14° to 131°F)
Frequency:
Consumption:
Fuse:
from 48 to 62 Hz
180 W max
10% to 90% relative humidity non-
condensing
T 3.15A H, 5 x 20 mm
Dimensions of projector: 352 mm x 174 mm x 318 mm
(LxHxD)
Safety:
EN 60950, UL 60950
desktop equipment
Transportability:
13”-7/8 x 6”-7/8 x 12”-1/2 (LxHxD)
Electromagnetic
compatibility:
EN 55022 Class B
EN 55024
EN 61000-3-2
EN 61000-3-3
Weight of projector:
5.0 kg (11 lbs)
Packaging and
gross weight:
400mm x 275 mm x 405 mm (LxHxD)
1’ 4” x 11” x 1’ 4” (LxHxD)
double reinforced carton;
expandable anti-shock
packaging;
Transportation:
IEC 68-2-31, IEC 68-2-32
gross
accessories:
kg (17.7 lbs); recyclable
packaging material
weight,
including
8
28
Download from Www.Somanuals.com. All Manuals Search And Download.
B DIMENSIONS
318 (12-1/2)
unit: mm (inches)
C PROJECTION DISTANCES
Follow the table below to determine the optimal projection distance “L” between the screen and the center of the lens. This will
help you to obtain the desired screen size.The manual lens shift adjustments allows the projected image to be moved vertically,
up or down, in relation to the centre of the screen (Fig.37b). If the distance “H” between the centre of the screen and the centre of
the lens exceed Hmax, it is necessary to tilt the projector and use the digital keystone to correct the image projected.
L
L
(Fig.37a)
(Fig.37b)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection distance table
16/9
Screen
size
Screen
width
Min projection distance
min L Hmax
Max projection distance
max L Hmax
(diagonal)
in.
m
ft. in.
m
ft. in.
m
in.
m
ft. in.
m
ft. in.
50"
60"
0,3
0,3
0,4
0,4
0,5
0,6
0,7
0,8
1,0
1,1
1,2
1,4
0’ 11”
1’ 1”
1’ 3”
1’ 6”
1’ 8”
1’ 10”
2’ 3”
2’ 9”
3’ 4”
3’ 8”
4’ 1”
4’ 7”
1,1
1,3
1,6
1,8
2,0
2,2
2,7
3,3
4,0
4,4
4,9
5,5
44”
52”
0,4
0,5
0,5
0,6
0,7
0,8
0,9
1,2
1,4
1,5
1,7
1,9
1’ 3”
1’ 6”
1’ 9”
2’ 0”
2’ 3”
2’ 6”
3’ 1”
3’ 9”
4’ 7”
5’ 1”
5’ 6”
6’ 4”
2,0
2,4
2,8
3,2
3,6
4,0
4,8
6,0
7,2
8,0
8,8
9,9
6’ 6”
7’ 10”
9’ 1”
2,7
3,3
3,8
4,4
4,9
5,5
6,6
8,2
9,9
9’ 0”
10’ 9”
12’ 7”
14’ 4”
16’ 2”
17’11”
21’ 7”
26’11”
32’ 4”
35’11”
39’ 6”
44’11”
70"
61”
80"
70”
10’ 5”
11’ 9”
13’ 1”
15’ 8”
19’ 7”
23’ 6”
26’ 1”
28’ 9”
32’ 7”
90"
78”
100"
120’
150"
180"
200"
220"
250"
87”
105”
131”
157”
174”
192”
218”
11,0
12,0
13,7
Projection distance table
4/3
Screen
size
Screen
width
Min projection distance
min L Hmax
ft. in.
Max projection distance
max L Hmax
ft. in.
(diagonal)
m
m
in.
m
in.
m
ft. in.
m
ft. in.
50"
60"
0,3
0,4
0,5
0,5
0,6
0,7
0,8
1,0
1,2
1,4
1,5
1,7
1’ 1”
1’ 4”
1’ 7”
1’ 10”
2’ 0”
2’ 3”
2’ 8”
3’ 4”
4’ 1”
4’ 6”
4’ 11”
5’ 8”
1,0
1,2
1,4
1,6
1,8
2,0
2,4
3,1
3,7
4,1
4,5
5,1
40”
48”
0,5
0,6
0,7
0,8
0,8
0,9
1,1
1,4
1,7
1,9
-
1’ 7”
1’ 10”
2’ 2”
2’ 6”
2’ 9”
3’ 1”
3’ 8”
4’ 8”
5’ 7”
6’ 2”
-
2,4
2,9
3,4
3,9
4,4
4,9
5,8
7,3
8,8
9,7
10,7
12,2
8’ 0”
3,4
4,0
4,7
5,4
6,0
6,7
8,0
10,1
12,1
13,4
-
11’ 0”
13’ 2”
15’ 7”
17’ 7”
19’ 9”
22’ 0”
26’ 5”
33’ 0”
39’ 7”
44’ 0”
-
9’ 7”
70"
56”
11’ 2”
12’ 6”
14’ 4”
16’ 0”
19’ 2”
23’11”
28’ 9”
31’11”
35’ 1”
39’11”
80"
64”
90"
72”
100"
120’
150"
180"
200"
220"
250"
80”
96”
120”
144”
160”
166”
200”
-
-
-
-
30
Download from Www.Somanuals.com. All Manuals Search And Download.
D ON SCREEN MENU LAYOUT
Picture
Video • S-Video
[NTSC]
YCrCb15kHz
RGBS 15kHz
RGBS
RGB Grafico
Digital Input
Video • S-Video
[PAL, SECAM]
YCrCb
Brightness
Contrast
Sharpness
Sharpness Mode
Brightness
Contrast
Color
Tint
Sharpness
Filter
Cinema Mode
Video Type
Noise reduction
Brightness
Contrast
Color
Sharpness
Filter
Cinema Mode
Video Type
Noise reduction
Brightness
Contrast
Color
Tint
Sharpness
Sharpness Mode
Not active
Auto
Manual
Value
Flesh tone correction
On Off
Flesh tone correction
On Off
Image
YCrCb
RGB
RGB Grafico
Digital Input
YCrCb 15kHz
RGBS 15kHz
Video • S-Video
Aspect
Aspect
Aspect
Aspect
Color Temperature
Gamma Correction
Overscan
Position
Y/C Delay
Color Temperature
Gamma Correction
Overscan
Color Temperature
Gamma Correction
Overscan
Color Temperature
Gamma Correction
Overscan
Position
Frequency
Phase
Position
Aspect
Color Temperature
Gamma Correction
Normal
High
Film
Anamorphic
Letterbox
Panoramic
Pixel to Pixel
User 1
Medium
Low
User
Video
Graphics
Horizontal
Vertical
Screen control
Red Offset
Green Offset
Blue Offset
Red Gain
Green Gain
Blue Gain
User 2
User 3
Horizontal
Vertical
Screen control
Horizontal
Vertical
Screen control
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Orientation
Keystone
Lens
Power ON
Test patterns
Initial settings
Floor
Floor-rear
Ceiling
Horizontal
Horizontal
Zoom
Focus
Ceiling-rear
Auto
Stand-by
English
Italiano
Français
Deusch
Español
Português
Menu
Language
Source list
F1/F2 keys
F1 F2
Source info
OSD background
OSD Position
OSD Timeout
Zoom
Focus
Magnification
Blank
Yes No
Color temperature
Gamma correction
1
1 VIDEO
VIDEO 1
2
2 S-VIDEO
S-VIDEO 2
Active Yes No
Name
3
3 COMPONENT / RGBS
COMP RGB 3
GRAPH RGB 4
DIGITAL INPUT 5
4
4 GRAPHICS RGB
5
5
DIGITAL INPUT
()?@
1
ABC
2
DEF
3
Edit source name
_ _ _ _ _ _ _ _ _ _ _
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
Cancel
-
Confirm
+
0
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Memories
Memories
0 Auto
()?@
1
ABC
2
DEF
3
1
2
3
S
S
S
MEMORY 1
MEMORY 2
MEMORY 3
Save current settings
Save initial settings
Rename
Edit memory name
_ _ _ _ _ _ _ _ _ _ _
GHI
4
JKL
5
MNO
6
PQRS
7
TUV
8
WXYZ
9
Cancel
-
Confirm
+
0
33
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
750 Palomar Avenue • Sunnyvale • CA 94085 • Phone (408) 735-1492
Download from Www.Somanuals.com. All Manuals Search And Download.
|