OWNER’S MANUAL
MANUAL DE INSTRUCCIONES
VIDEO CASSETTE RECORDER
VIDEOGRABADOR DE CASSETTE
MVR4051/MVR4052
ATTENTION
ATENCION
If you purchase a universal remote control from your local retailer, please contact the
remote manufacturer for the required programming code.
Si usted a comprado un control remoto universal, por favor comunicace con el fabricante
para el codico de programaccion requerido.
TV/CATV MODE SELECTION
SELECCION DE MODO DE TV/CATV
When shipped from the factory, the TV/CATV menu option is set to the "CATV" (Cable
Television) mode.
If not using CATV (Cable TV), set this menu option to the "TV" mode.
Al salir la unidad de fábrica, la opción de menú de TV/CATV se ajusta al modo de
"CATV" (Televisión por cable).
Si no utiliza CATV, ajuste esta opción de menú al modo de "TV".
Before operating the unit, please read this manual thoroughly.
Antes de usar la unidad, lea detenidadmente este manual de instrucciones.
4F21301B E COV-07
1
6/26/02, 3:56 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
9. VENTILATION
13. LIGHTNING
Slots and openings in the cabinet back or bottom
are provided for ventilation and to ensure reliable
operation of the unit and to protect it from overheating.
These openings must not be blocked or covered.
The openings should never be blocked by placing
the unit on a bed, sofa, rug, or other similar surface.
This unit should never be placed near or over a
radiator or heat source. This unit should not be
placed in built-in installations such as a bookcase or
rack unless proper ventilation is provided or the
manufacturer's instructions have been adhered to.
10. POWER SOURCES
To protect your unit from a lightning storm, or when
it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent
damage to the unit due to lightning and power line
surges.
14. POWER LINES
An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside
antenna system, extreme care should be taken to
keep from touching such power lines or circuits, as
contact with them might be fatal.
This unit should be operated only from the type of
power source indicated on the rating plate. If you are
not sure of the type of power supply to your home,
consult your appliance dealer or local power com-
pany. For units intended to operate from battery
power, or other sources, refer to the operating
instructions.
15. OVERLOADING
Do not overload wall outlets and extension cords, as
this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit
as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock.
Never spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected
to the unit, be sure the antenna or cable system is
grounded to provide some protection against voltage
surges and built-up static charges. Section 810 of
the National Electrical Code, ANSI/NFPA 70,
provides information with respect to proper grounding
of the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge
unit, connection to grounding electrodes, and
requirements for the grounding electrode.
18. SERVICING
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternating-
current line plug (a plug having one blade wider than
the other). This plug will fit into the power outlet only
one way. This is a safety feature. If you are unable
to insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug If your
unit is equipped with a 3-wire grounding-type plug, a
plug having a third (grounding) pin, this plug will only
fit into a grounding-type power outlet. This too, is a
safety feature. If you are unable to insert the plug
into the outlet, contact your electrician to replace
your obsolete outlet.
Do not defeat the safety purpose of the grounding-
type plug.
Do not attempt to service this unit yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
3
4F21301B E COV-07
3
6/26/02, 3:56 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
20. REPLACEMENT PARTS
19. DAMAGE REQUIRING SERVICE
Unplug this unit from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
When replacement parts are required, be sure the
service technician uses replacement parts specified
by the manufacturer or those that have the same
characteristics as the original parts.
Unauthorized substitutions may result in fire, electric
shock or other hazards.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the unit.
21. SAFETY CHECK
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an improper adjustment of
other controls may result in damage and will
often require extensive work by a qualified
technician to restore the unit to its normal
operation.
Upon completion of any service or repairs to this
unit, ask the service technician to perform safety
checks to determine that the unit is in proper
operating condition.
22. WALL OR CEILING MOUNTING
The product should be mounted to a wall or ceiling
only as recommended by the manufacturer.
23. HEAT
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
24. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as practical.
e. If the unit has been dropped or the cabinet has
been damaged.
f. When the unit exhibits a distinct change in
performance, this indicates a need for service.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
NATIONAL ELECTRICAL CODE
ANTENNA LEAD IN WIRE
GROUND CLAMP
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC SERVICE
EQUIPMENT
GROUND CLAMPS
NEC-NATIONAL ELECTRICAL CODE
S2898A
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
4
4F21301B E COV-07
4
6/26/02, 3:56 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
• When you finish operating the VCR, always unload
the cassette and turn off the power.
MOISTURE CONDENSATION
DO NOT OPERATE THIS VCR FOR AT LEAST TWO
OR THREE HOURS WHEN MOISTURE IN THE AIR
CONDENSES ON THE VCR.
• When you leave your home for a long time, unplug the
AC power cord.
WHAT IS MOISTURE CONDENSATION?
• To protect the VCR from a lightning storm, unplug the
AC power cord from the wall outlet and disconnect the
antenna.
When a cold liquid is poured into a glass, for example,
water vapor in the air will condense on the surface of the
glass. This is called moisture condensation.
MOISTURE WILL CONDENSE ON THE UNIT IN THE
FOLLOWING CASES;
• When you move this VCR from a cold to a warm place.
• After heating a cold room or under extremely humid
conditions.
POWER SOURCE
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for operation on
AC. Insert the AC cord plug into a standard 120V 60Hz
polarized AC outlet.
WHEN YOU EXPERIENCE THE ABOVE CONDITIONS,
Plug the power cord into an AC outlet, press the POWER
button to turn on and leave the unit at room temperature
until moisture condensation disappears.
Depending on the surrounding conditions, this may take
two or three hours.
SURGE PROTECTORS:
It is recommended to use a surge protector for AC
connection. Lightening and power surges ARE NOT
covered under warranty for this product.
NOTES:
LOCATION AND HANDLE
1. Never connect the AC line cord plug to other than the
specified voltage (120V 60Hz). Use the attached
power cord only.
2. If the polarizedAC cord does not fit into a non-polarized
AC outlet, do not attempt to file or cut the blade. It is the
user’s responsibility to have an electrician replace the
obsolete outlet.
• If you cause a static discharge when touching the VCR,
and the VCR fails to function, simply unplug the unit
from the wall outlet, wait 10 minutes and plug it back
in. The VCR should return to normal operation.
• Avoid extreme heat or cold. (41˚F/5˚C-104˚F/40˚C)
• Do not place the VCR on or near appliances which
may cause electromagnetic interference, e.g. TV,
speakers, etc. Doing so may cause erratic operation
of the VCR including picture and/or sound distortion or
noise.
AC Outlet
Wider Hole
and Blade
• Avoid extreme moisture and dust.
• The ventilation holes prevent overheating. Do not
block or cover these holes. Especially avoid covering
the holes with soft materials such as cloth or paper.
• Do not insert fingers or any other objects into the
cassette loading slot. Do not spray cleaner or wax
directly on the VCR or use forced air to remove dust.
Polarized AC Cord Plug
(One blade is wider than the other)
• Avoid places subject to strong vibration. Use in a
horizontal (flat) position only.
• Keep the VCR away from flower vases, sinks, etc.
If liquids should be spilled into the VCR, serious
damage will result. If you spill any liquids into the
VCR, unplug the AC power cord immediately and
consult qualified service personnel before attempting
to use the VCR again.
5
4F21301B E COV-07
5
6/26/02, 3:56 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
FEATURES
High Quality Picture Technology - This video cassette
recorder marked "HQ" incorporates VHS high quality
technology. A built-in detail enhancer is used to boost
the recorded signal and provide maximum picture
quality in playback. It is compatible with other VHS video
cassette recorders.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this
device:
•
•
Use only the size and type of batteries specified.
Be sure to follow the correct polarity when installing
the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
4 Video Heads - Provides optimal picture quality for
special effects playback.
•
•
•
Do not mix different types of batteries together (e.g.
Alkaline and Carbon-zinc) or old batteries with fresh
ones.
Hi-Fi Stereo Sound - With a frequency response of 100
to 10,000 Hz and a dynamic range of better than 90dB,
this VCR provides a level of excellence that rivals
compact discs.
If the device is not to be used for a long period of
time, remove the batteries to prevent damage or
injury from possible battery leakage.
8-Program/1-Month Programmable Timer with
Everyday/Every Week Capability - The built-in timer
allows automatic absentee recording of up to 8 TV
programs within 1 month. It is also possible to record a
program which is broadcast at the same time everyday
or every week.
Do not try to recharge batteries not intended to be
recharged; they can overheat and rupture. (Follow
battery manufacturer's directions.)
On-Screen Display and Programming - When you
select a channel or make other changes, the TV will
show an indicator on the screen for a few seconds.
Clock settings, timer setting and other set-up operations
can be carried out using the on-screen display menu
system.
BATTERY INSTALLATION
• Open the battery
compartment cover.
• Install two "AAA"
batteries.
Digital Auto Tracking - Automatically adjusts tracking
during playback for the best possible picture.
• Replace the cover.
181 Channel Tuner - Receives standard VHF and UHF
broadcast channels and up to 113 cable channels.
EFFECTIVE DISTANCE OF THE
REMOTE CONTROL
One-touch Timer Recording (OTR) - Simply by
pressing the REC/OTR button, the VCR can be pro-
grammed for up to 5 hours of recording with an immedi-
ate start.
Automatic Power On - When loading a cassette tape,
this VCR will automatically turn on.
Automatic Playback - When loading a cassette tape with-
out the erase prevention tab, this VCR will automatically
turn on and play back the cassette tape at the correct
speed.
15 FEET
30˚
30˚
Automatic Rewind-Stop-Eject-Power Off - When a
tape reaches its end during playback and recording, it
will automatically stop, rewind, stop, eject the tape and
the VCR will turn off.
NOTES: • When direct sunlight, an incandescent lamp,
fluorescent lamp or any other strong light
shines on the Remote Sensor, the remote
operation may be unstable.
• When there is an obstacle between the VCR
and the remote control, the remote control
may not operate.
6
4F21301B E COV-07
6
6/26/02, 3:56 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Automatic Repeat Play System - When the AUTO
REPEAT option is turned on, this VCR will automatically
play back the same cassette tape repeatedly.
CAUTIONS
IMPORTANT SAFEGUARDS .................................... 2
PRECAUTIONS ......................................................... 5
On-Screen 3 Language Display - This TV can display
the on screen language in English, Spanish or French.
PREPARATION
Slow Motion - This VCR provides slow motion which
FEATURES ................................................................ 6
LOCATION OF CONTROLS ...................................... 8
BASIC CONNECTIONS........................................... 10
CATV (CABLE TV) CONNECTIONS ....................... 12
AUDIO/VIDEO CONNECTIONS .............................. 14
SETTING THE VIDEO CHANNEL ........................... 15
LANGUAGE SELECTION ........................................ 15
SETTING THE CLOCK ............................................ 15
SETTING THE CHANNELS ..................................... 16
NOISE ELIMINATION .............................................. 16
offers steady, noise free playback at 1/10 normal speed.
Frame by Frame Advance - Press the SLOW button
during still playback to advance the tape one frame at
a time.
Real Time Tape Counter - The counter displays on the
screen the elapsed time in hours, minutes and seconds
and can be used to locate programs.
2 Speed Picture Search - 3 or 5 times normal speed in
SP mode (7X or 9X in LP and 9X or 15X in SLP).
PLAYBACK
3 Speed Playback - Plays three tape speeds (SP, LP,
LOADING AND UNLOADING .................................. 17
PLAYBACK .............................................................. 17
SPECIAL PLAYBACK .............................................. 18
SLP).
2 Speed Record - Records two tape speeds (SP, SLP).
Stereo/SAP Reception - This VCR is designed to receive
stereo and separate audio program (SAP) broadcasts
where available.
RECORDING
RECORDING A TV PROGRAM............................... 18
ONE-TOUCH TIMER RECORDING (OTR) ............. 20
SETTING THE TIMER RECORDING ...................... 20
Front Audio/Video In Jacks - A VCR or other video
device may be hooked up for dubbing.
ADDITIONAL INFORMATION
ON-SCREEN FUNCTION DISPLAY ........................ 21
STEREO RECORDING AND PLAYBACK ............... 22
SEPARATE AUDIO PROGRAM (SAP) ................... 22
DUPLICATING A VIDEO TAPE ............................... 23
VIDEO HEAD CLEANING........................................ 23
BEFORE REQUESTING SERVICE ......................... 24
SPECIFICATIONS ................................................... 25
7
4F21301B E COV-07
7
6/26/02, 3:56 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION OF CONTROLS
1
2
3
4
5
6
FRONT
POWER
PLAY
F.FWD
STOP/
EJECT
REC/OTR
REW
(MONO)
VIDEO IN
L
–
AUDIO IN
–
R
CHANNEL
TV/VCR
T.REC
REC
POWER
14
13 12 11 10
9
8
7
REMOTE CONTROL
1. Cassette Loading Slot - To insert or remove a
video tape.
2. REW button - In the STOP mode, this button rapidly
winds the tape backwards. In the PLAY mode, this
button activates Reverse Search.
3. PLAY button - Press to play a prerecorded tape.
4. STOP/EJECT button - Press once to stop the tape in
any mode. Press again to eject the tape.
5. F. FWD button - In the STOP mode, this button
rapidly winds the tape forward. In the PLAY mode,
this button activates Forward Search.
6. POWER button - Turns the VCR power on and off.
7. REC/OTR button - Press once to start normal
recording. Additional presses activate One-touch
Timer Recording.
8. CHANNEL Up / Down buttons - Used to select a
channel for viewing or recording.
9. Remote Sensor - Signals from the Remote Control
are received here.
10. POWER indicator - Lights up when the power is
turned on.
11. REC indicator - Lights up during recording.
12. T. REC indicator - Lights when the unit is in the
Timer Record mode.
6
POWER
1
4
7
2
5
8
3
6
15
8
9
CHANNEL
0
24
REC/OTR
PAUSE/STILL
7
PLAY
3
5
2
16
17
REW
F.FWD
MENU
ENTER
STOP
TRACKING
–
+
25
SET
AUTO
TIMER REC
TRACKING CANCEL
18
19
20
21
22
26
27
SLOW
COUNTER
RESET
AUDIO
INPUT
SELECT
SELECT
TV/VCR SPEED
CALL
28
29
30
13. TV/VCR indicator - Lights up when the TV/VCR
selector button is selected to the VCR mode.
23
CONTINUED ON NEXT PAGE
8
4F21301A E P08-13
8
6/26/02, 3:52 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR
31
32
UHF/VHF
IN(ANT)
OUT
VIDEO
L
OUT(TV)
AUDIO
R
CH
3
4
34
33
35
14. AUDIO (L/R)/VIDEO In Jacks - Audio and video
signal cables from an external source can be
connected here.
15. Direct Channel Selection buttons (0-9) - Allows
direct access to any channel.
16. STOP button - Press to stop the tape.
17. MENU button - Press to display the on-screen menu
function.
18. TRACKING SET + / – buttons - During playback, they
are used to adjust tracking manually. Used to set or
adjust in the menu mode.
19. TIMER REC button - Used to set the VCR to start
recording at a preset time (Timer program must be
set).
20. SLOW button - Press to play back a tape in slow
motion or to advance the tape one frame at a time
during still playback.
25. ENTER button - Used to enter the information in the
menu mode.
26. CANCEL button - Used to clear the selected timer
recording program.
27. AUTO TRACKING button - Allows automatic adjust-
ment of tracking to minimize picture noise during play-
back.
28. INPUT SELECT button - Switches the program for
viewing between the VCR and external input sources.
29. AUDIO SELECT button - Switches sound between
mono and stereo, and SAP when receiving broad-
casts in stereo or SAP.
30. CALL button - Displays the present time/day of the
week, channel, counter, speed selection and VCR
mode on the TV screen.
31. AUDIO (L/R) / VIDEO OUT Jacks - Use to output
audio and video signal to a TV, amplifier or VCR.
32. UHF/VHF IN (ANT) Jack - Connect a UHF/VHF
antenna or CATV cable to this jack.
21. COUNTER RESET button - Resets the Real Time
Tape Counter to 00:00:00.
22. TV/VCR selector button - Switches between TV
and VCR.
33. UHF/VHF OUT (TV) Jack - Use to output UHF/VHF
or CATV signal to a TV.
23. SPEED (SP/SLP) selector button - Sets the tape
speed for recording.
24. PAUSE/STILL button - During recording, this
34. 3/4 Channel Selector Switch - Selects the channel
through which the VCR outputs its signal to a TV.
35. AC Power Cord - Connect to a 120V 60Hz outlet.
button temporarily stops the tape. The "
" will
appear on the screen. During playback, it stops the
tape and displays a still image on the TV screen.
9
4F21301A E P08-13
9
6/26/02, 3:52 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC CONNECTIONS
If you are using an antenna system, follow the instructions. If you are a cable (CATV) subscriber, skip ahead to
page 12 for the proper connections.
ANTENNA TO VCR CONNECTION
The VCR must be connected "between" the antenna and the TV. First, disconnect the antenna from the TV and connect
it to the VCR. Then connect the VCR to the TV. Below are 3 common methods of connecting an antenna system to a
VCR. Find the type of antenna system you are using and follow the connection diagram.
Combination VHF/UHF Antenna with 75 ohm Coaxial Cable
VCR
1
IN
75 ohm Coaxial Cable
OUT
Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire
2
3
VCR
Matching Transformer
300 ohm Input
IN
75 ohm output
(not supplied)
OUT
300 ohm Twin Lead (Flat) Wire
VCR
Separate VHF and UHF Antennas
Combiner
75/300 ohm Inputs
75 ohm output
(not supplied)
UHF
VHF
IN
300 ohm Twin Lead (Flat) Wire
OUT
75 ohm Coaxial Cable
NOTE: If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300 ohm
inputs and one 75 ohm output.
NOTES: • A clear picture will not be obtained by the VCR unless the antenna signal is good. Connect the antenna to the
VCR properly.
• For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an
outdoor type antenna is required.
• If you are not sure about the connection, please refer to qualified service personnel.
10
4F21301A E P08-13
10
6/26/02, 3:52 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
VCR TO TV CONNECTION
After you have connected the antenna to the VCR, you must connect the VCR to the TV.
Below are 3 common methods of connecting your VCR to a TV. Find the type of TV you are using and follow the
connection diagram.
This VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna inputs
(numbers 2 and 3 below), use a splitter to connect the VCR to the TV for VHF and UHF reception.
TV
NOTE: If a VHF or UHF antenna
is used, set the TV/CATV
menu option to the "TV"
mode.
IN
VHF/UHF IN
OUT
75 ohm Coaxial Cable (supplied)
TV with single 75 ohm
VHF/UHF antenna input
NOTE: If a VHF or UHF antenna
TV
is used, set the TV/CATV
Splitter
75 ohm Input
75/300 ohm outputs
(not supplied)
menu option to the "TV"
mode.
UHF
VHF
IN
75 ohm Coaxial Cable
(supplied)
OUT
TV with 300 ohm UHF
and 75 ohm VHF
antenna inputs
TV
NOTE: If a VHF or UHF antenna
is used, set the TV/CATV
menu option to the "TV"
mode.
UHF
Splitter
75 ohm Input
300 ohm outputs
(not supplied)
IN
75 ohm Coaxial Cable
(supplied)
VHF
OUT
TV with 300 ohm UHF
and 300 ohm VHF
antenna inputs
11
4F21301A E P08-13
11
6/26/02, 3:52 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
CATV (CABLE TV) CONNECTIONS
Many cable companies offer services permitting reception of extra channels including pay or subscription channels.
This VCR has an extended tuning range and can be tuned to most cable channels without using a cable company
supplied converter box, except for those channels which are intentionally scrambled. If you subscribe to a special
channel which is scrambled, you must have a descrambler box for proper reception.
VCR
1
TV
IN
VHF/UHF
IN (ANT)
Incoming Cable
OUT
ALLOWS: Recording of nonscrambled channels.
*
*
*
Use of the programmable timer.
Recording of one channel while watching another.
VCR
2
Converter/
Descrambler
TV
IN
VHF/UHF
IN (ANT)
Incoming
Cable
OUT
ALLOWS: Recording of channels through the converter box
*
(scrambled and unscrambled).
Using the programmable timer to record only the
channel selected at the converter box.
NOTE:
*
To record from converter/descrambler, VCR
tuner must be tuned to the converter output
channel, usually channel 3 or 4.
PREVENTS: Recording one channel while watching another.
*
Using the VCR tuner to select channels.
*
VCR
3
TV
IN
VHF/UHF
IN (ANT)
Converter/Descrambler
Incoming Cable
OUT
ALLOWS: Recording of nonscrambled channels.
*
NOTE:
Use of the programmable timer.
Recording an unscrambled channel while watching
any channel selected at the converter box.
*
*
If you are playing a tape or using the tuner
built into the VCR, the converter must be set
to the video channel output of the VCR
(either 3 or 4).
PREVENTS: Recording scrambled channels.
NOTE: Whenever a Converter/Descrambler box is placed before the VCR, you must tune the VCR to the output of
the Converter/Descrambler box, usually channel 3 or 4.
12
4F21301A E P08-13
12
6/26/02, 3:52 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: Make sure the TV/CATV menu option is set to the "CATV" mode.
This VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambled
programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult
your local cable company for more information concerning connection to their descrambler equipment. There are
many ways to connect your VCR to a cable system. Below are six common methods of connection.
VCR
TV
Splitter
4
A/B Switch
VHF/UHF
IN (ANT)
IN
Incoming
A
Cable
OUT
B
Converter/Descrambler
ALLOWS: Recording of one channel while watching another.
*
*
*
Using the programmable timer to record only the channel selected at the converter box.
Recording of all channels through the converter box.
PREVENTS: Watching scrambled channels while recording another channel.
*
*
Using the VCR tuner to select channels.
VCR
5
TV
Splitter
IN
VHF/UHF
IN (ANT)
OUT
Converter/
Descrambler
A/B Switch
Incoming
Cable
A
B
ALLOWS: Recording of nonscrambled channels.
*
Recording of one channel while watching another.
Watching premium channels through the converter while recording nonscrambled channels.
Using the programmable timer.
*
*
*
PREVENTS: Recording scrambled channels.
VCR
Converter/
Descrambler
6
TV
Splitter
IN
VHF/UHF
IN (ANT)
OUT
Incoming
Converter/
Descrambler
A/B Switch
Cable
A
B
ALLOWS: Recording of all channels through the converter box.
*
*
Recording a scrambled or unscrambled channel while watching another (scrambled or
unscrambled) channel.
Using the programmable timer to record only the channel selected at the converter box.
PREVENTS: Using the VCR tuner to select channels.
*
13
4F21301A E P08-13
13
6/26/02, 3:52 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO/VIDEO CONNECTIONS
If your TV has AUDIO IN and VIDEO IN jacks, you can connect your VCR to them to receive a higher quality
picture and sound. If you have a stereo, you can connect a stereo amplifier to enjoy powerful sound.
AUDIO/VIDEO CONNECTION
From ANTENNA/CATV system
VCR
To UHF/VHF IN
TV
IN
To VIDEO OUT
OUT
To AUDIO (L) OUT
To AUDIO (R) OUT
To UHF/VHF OUT
To ANT IN
To VIDEO IN
To AUDIO (R) IN
To AUDIO (L) IN
AUDIO/VIDEO Cord (not supplied)
1. Connect the VIDEO OUT jack on the VCR to the VIDEO IN jack on the TV.
2. Connect the AUDIO (L/R) OUT jacks on the VCR to the AUDIO (L/R) IN jacks on the TV.
3. Set the VIDEO/TV selector of your TV to "VIDEO".
STEREO AMPLIFIER CONNECTIONS
When you connect your VCR to a Stereo Component System, you can view the picture from the VCR while
enjoying powerful sound from your audio system.
From ANTENNA/CATV system
VIDEO Cord
To UHF/VHF IN
TV
To VIDEO IN
To ANT IN
(not supplied)
VCR
To VIDEO OUT
IN
To AUDIO (L) OUT
To AUDIO (R) OUT
OUT
To UHF/VHF OUT
To AUX (R) IN
To AUX (L) IN
AUDIO Cord (not supplied)
Connect the AUDIO (L/R) OUT jacks on the VCR to the AUX (L/R) IN jacks on the stereo amplifier.
14
4F21301A E P14-19
14
6/26/02, 3:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE VIDEO
CHANNEL
To view playback of a recorded tape, or to watch a
program selected by the VCR's channel selector, the
TV must be set to channel 3 or 4 (video channel).
2 Press the TRACKING SET +
or – button to select the
desired language: English
(ENGLISH), Spanish
LANGUAGE/IDIOMA/LANGUE
ENGLISH
ESPAÑOL
FRANCAIS
(ESPAÑOL) or French
(FRANCAIS), then press the
ENTER button.
When a TV is connected with the 75 ohm coaxial cable
only.
〈
+ –
/
〉
/ENTER/MENU
1 Press the POWER button to turn the VCR on.
3 Press the MENU button until the menu screen is
2 Set the 3/4 Channel selector switch (Rear of the
cleared.
VCR) to CH 3 or 4.
3 Turn ON the TV and set to CH 3 or 4 to correspond
SETTING THE CLOCK
with the channel selected in step 2.
4 Press the TV/VCR selector button to select VCR.
You must set the date and time manually for timer
recordings.
The TV/VCR indicator will light.
CH 125
5 Select any channel to receive
EXAMPLE: Setting the clock to "8:30 AM" October, 26th
a TV station in your area.
The channel number will
appear on the screen for about
4 seconds.
(FRI), 2001.
CHECK BEFORE YOU BEGIN
• Turn ON the TV and set to the video channel 3 or 4.
• Press the POWER button to turn the VCR on.
• Press the TV/VCR selector button to select the VCR
mode.
For a push-button TV tuner
If CH 3 or 4 corresponding to the video channel cannot
be tuned on your TV, proceed as follows: set the VCR 3/
4 channel selector and the TV to CH 3 or 4, play back a
prerecorded tape and tune the TV to receive a sharp
color picture from the video cassette recorder. Refer to
your TV owner's manual for details.
When a TV is connected with an audio/video cable, turn
the TV and this VCR on, and select the video input
mode on the TV.
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
1 Press the MENU button. Press
the TRACKING SET + or –
ON OFF
ON OFF
button to select the CLOCK SET
option, then press the ENTER
button.
ON OFF
〈+/–/ENTER/MENU〉
LANGUAGE SELECTION
This VCR can display on the TV screen in the English,
Spanish or French language.
On-screen language selection (step 2) will
automatically appear on the screen when you press
the MENU button initially. Select the language you
prefer first, then proceed with the other menu
options.
2 Press the TRACKING SET + or
4
MONTH
DAY
10
1
– button to set the month, then
press the ENTER button.
(SUN)
YEAR
TIME
2000
12
3 Set the day, year and time as in
:
00 AM
Step 2.
+ –
/
/ENTER/CANCEL/MENU
• The day of the week will
automatically appear when
you set the year.
• Press and hold down the
button to increase/ decrease
the minute by 10.
MONTH
DAY
10
26 (FRI)
2001
CHECK BEFORE YOU BEGIN
YEAR
TIME
• Turn ON the TV and set to the video channel 3 or 4.
• Press the POWER button to turn the VCR on.
• Press the TV/VCR selector button to select the VCR
mode.
8
:
30 AM
• After setting the clock, date
and time starts functioning
automatically.
〈
+ –
/
〉
/ENTER/CANCEL/MENU
NOTES: • After a power failure o
1
r disconnection of the
2
When a TV is connected with an audio/video cable,
turn the TV and this VCR on and select the video input
mode on the TV.
power, the timer settings will be lost. In this
case, reset the present time.
• Press the CANCEL button to move cursor
backward for correction.
MENU
1 Press the MENU button.
CLOCK SET
• If you want to correct time or date while the
clock is functioning, press the MENU button,
then press TRACKING SET + or – button to
select the CLOCK SET option, then press the
ENTER button.
TIMER REC SET
Press the TRACKING SET +
AUTO REPEAT
CH SET UP
SAP
ON OFF
ON OFF
or – button to select the
LANGUAGE option, then
press the ENTER button.
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
〈+/–/ENTER/MENU〉
To make any adjustments perform steps 2
through 3.
15
4F21301A E P14-19
15
6/26/02, 3:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE CHANNELS
This VCR is equipped with a channel memory feature
which allows channels to skip up or down to the next
channel set into memory, skipping over unwanted
channels. Before selecting channels, they must be
programmed into the VCR’s memory. In addition to
normal VHF and UHF channels, this VCR can receive
up to 113 Cable TV channels. To use this VCR with an
antenna, set the TV/CATV menu option to the TV mode.
When shipped from the factory, this menu option is in
the CATV mode.
TO ADD/DELETE CHANNELS
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
1 Press the MENU button.
Press the TRACKING SET +
or – button to select the CH
SET UP option, then press the
ENTER button.
ON OFF
ON OFF
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
〈+/–/ENTER/MENU〉
2 Press the TRACKING SET + or
– button to select the ADD/DE-
LETE mode, then press the
ENTER button.
CH SET UP
TV CATV
AUTO CH MEMORY
ADD/DELETE
TV/CATV SELECTION
MENU
1 Press the MENU button.
CLOCK SET
3 Select the desired channels to
be added or deleted using the
TRACKING SET + or – button.
TIMER REC SET
〈
+ –
〉
/ENTER/MENU
/
AUTO REPEAT
CH SET UP
SAP
ON OFF
ON OFF
2 Press the TRACKING SET + or –
button to select the CH SET UP
option, then press the ENTER
button.
ADD
CH 002
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
4 Press the ENTER button if you
wish to DELETE the channel
from memory.
〈+/–/ENTER/MENU〉
3 Press the TRACKING SET + or
– button to select the TV/CATV
mode.
CH SET UP
TV CATV
AUTO CH MEMORY
ADD/DELETE
〈
+ –
/
〉
/ENTER/MENU
Press the ENTER button if
you wish to ADD the
4 Press the ENTER button to select
the TV or CATV mode. The arrow
indicates the selected mode.
unmemorized channel.
Repeat Steps 3 and 4 for each channel to be added
or deleted.
〈
+ –
/
〉
/ENTER/MENU
TV
- VHF/UHF channels
CATV - CABLE TV channels
5 Press the MENU button three times after adding or
deleting all of the desired channels, to return to
normal TV viewing.
5 Press the MENU button twice to return to normal TV
viewing.
AUTOMATIC MEMORY TUNING
The VCR can receive a maximum of 181 channels by
presetting the channels into memory.
NOISE ELIMINATION
CHECK BEFORE YOU BEGIN
When you don't want to receive a weak signal
broadcast, the Blue back screen can be obtained by
selecting the NO NOISE BACKGROUND "ON". When
the unit is shipped from the factory, the NO NOISE
BACKGROUND is set to the "ON".
• Turn ON the TV and set to the video channel 3 or 4.
• Press the POWER button to turn the VCR on.
• Press the TV/VCR selector button to select the VCR
mode.
When a TV is connected with an audio/video cable, turn
the TV and this VCR on, and select the video input mode
on the TV.
CHECK BEFORE YOU BEGIN
MENU
• Turn ON the TV and set to the video channel 3 or 4.
• Press the POWER button to turn the VCR on.
• Press the TV/VCR selector button to select the VCR
mode.
CLOCK SET
1 Press the MENU button.
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
ON OFF
Press the TRACKING SET + or
– button to select the CH SET
UP option, then press the
ENTER button.
ON OFF
〈+/–/ENTER/MENU〉
When a TV is connected with an audio/video cable,
turn the TV and this VCR on and select the video input
mode on the TV.
CH SET UP
2 Press the TRACKING SET + or
– button to select the AUTO CH
MEMORY mode, then press the
ENTER button.
TV CATV
AUTO CH MEMORY
ADD/DELETE
MENU
CLOCK SET
1 Press the MENU button, then
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
ON OFF
press the TRACKING SET + or
– button to select the NO
3 The auto tuning will start.
The channel display will count
up and when finished, the
screen returns to normal.
Channel numbers will remain
red until auto memorizing is
complete.
〈
+ –
/
〉
/ENTER/MENU
NOISE BACKGROUND option.
ON OFF
〈+/–/ENTER/MENU〉
CH 001
2 Press the ENTER button to
MENU
CLOCK SET
TIMER REC SET
select the ON position.
AUTO REPEAT
CH SET UP
SAP
ON OFF
ON OFF
3 Press the MENU button again.
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
〈+/–/ENTER/MENU〉
16
4F21301A E P14-19
16
6/26/02, 3:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADING AND UNLOADING
Use only video cassette tapes marked
.
TO STOP PLAYBACK
Press the STOP button once.
The tape will stop but remain fully
loaded and ready to play.
LOADING
Push the center of the tape until it
is automatically retracted.
"
" will appear on the screen for
AUTOMATIC POWER ON
The VCR will turn on automatically
and the POWER indicator will light.
about 4 seconds.
This VCR selects the playback tape speed SP, LP or
SLP automatically.
AUTOMATIC PLAY
When loading a cassette tape without the erase preven-
tion tab, playback will start immediately.
Insert the cassette with its labeled side facing you. An
inverted cassette cannot be inserted.
TO REWIND OR FORWARD THE TAPE
RAPIDLY
Press the REW button in the
STOP mode.
UNLOADING
To unload a cassette, press the
STOP/EJECT button on the VCR
twice. The first press will stop the
tape in any mode. The second
press will eject the tape. " " will
appear on the screen for about 4
seconds.
"
" will appear on the screen for
about 4 seconds.
Press the F.FWD button in the
STOP mode.
"
" will appear on the screen for
about 4 seconds.
AUTOMATIC EJECT
If the VCR automatically rewinds the tape to the begin-
ning (AUTO REWIND FEATURE), the tape will be
ejected automatically (See the NOTE on page 19).
FORWARD/REVERSE PICTURE SEARCH
If you want to see the tape program during REW or
F.FWD mode, press and hold the REW or F.FWD button
again. The backward or forward visual search picture
will be seen on the screen. Release the button to return
to the REW or F.FWD mode.
NOTES: • Always eject the tape when not in use.
• The cassette can be ejected even if the VCR
is turn off.
DIGITAL TRACKING CONTROL
PLAYBACK
When a tape is played, the Digital Auto Tracking System
automatically adjusts the tracking to obtain the best
possible picture. If noise bars appear during playback,
adjust the tracking manually:
To play a prerecorded cassette tape.
TO START PLAYBACK
• Press the TRACKING SET + or – button to obtain the
best possible picture. To resume automatic tracking,
press the AUTO TRACKING button.
CHECK BEFORE YOU BEGIN
Turn ON the TV and set to the video channel 3 or 4.
When a TV is connected with an audio/video cable,
turn the TV and this VCR on and select the video input
mode on the TV.
1 Load a prerecorded tape
(When loading a cassette tape
without the erase prevention
tab, playback will start auto-
matically).
2 Press the PLAY button.
Playback will start.
"
" will appear on the screen
for about 4 seconds.
17
4F21301A E P14-19
17
6/26/02, 3:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL PLAYBACK
TO VISUALLY SEARCH FOR
DESIRED POINTS
TO WATCH A TAPE REPEATEDLY
CHECK BEFORE YOU BEGIN
When either the F.FWD or REW button is pressed in the
PLAYBACK mode, the speed search picture will appear.
When pressed twice, the search picture will increase
speed. Speed search time depends upon the speed
used (SP, LP or SLP) during recording.
• Turn ON the TV and set to the video channel 3 or 4.
• Press the POWER button to turn the VCR on.
• Press the TV/VCR selector button to select the VCR
mode.
When a TV is connected with an audio/video cable,
turn the TV and this VCR on, and select the video input
TO WATCH A STILL PICTURE
Press the PAUSE/STILL button in the PLAYBACK mode.
Press the PAUSE/STILL button again to resume normal
playback.
mode on the TV.
MENU
CLOCK SET
1 Press the MENU button.
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
ON OFF
Press the TRACKING SET +
or – button to select the AUTO
REPEAT option.
FRAME BY FRAME ADVANCE
ON OFF
〈+/–/ENTER/MENU〉
2 Press the ENTER button to
Press the SLOW button during STILL playback.
The still picture will advance by one frame each time
you press the button. Hold the button for continuous
frame by frame viewing.
Press the PAUSE/STILL button again to resume normal
playback.
MENU
CLOCK SET
TIMER REC SET
select the ON position.
AUTO REPEAT
CH SET UP
SAP
ON OFF
ON OFF
3 Press the MENU button.
If you press the PLAY button, the
tape will play over and over until
the repeat mode is canceled.
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
〈+/–/ENTER/MENU〉
NOTES: • A few noise bars will appear on the picture
during SPEED SEARCH and STILL.
• The audio output is muted during SPEED
SEARCH, STILL, FRAME ADVANCE and
SLOW MOTION.
"
" will appear if you press the CALL button.
To remove the
again.
on the screen, press the CALL button
NOTE: To cancel repeat mode, follow the above steps
1 and 2, then press the ENTER button to select
the OFF position. Press the MENU button to
return to the TV.
• To prevent damage to the tape, special
playback is automatically changed to the
PLAYBACK mode after 5 minutes.
SLOW MOTION PLAYBACK
Press the SLOW button in the PLAYBACK mode.
Playback will proceed at 1/10th of the normal speed.
Press the PLAY button again to resume normal playback.
RECORDING A TV
PROGRAM
RECORDING AND VIEWING THE
SAME TV PROGRAM
NOTE: SLOW TRACKING AND VERTICAL LOCK
ADJUSTMENT
If noise bars appear in the picture during slow motion,
press the TRACKING SET + or – button to reduce the
noise bars.
If the still picture jitters excessively, press the
TRACKING SET + or – button to stabilize the still
picture.
CHECK BEFORE YOU BEGIN
• Turn ON the TV and set to the video channel 3 or 4.
• Press the POWER button to turn the VCR on.
• Press the TV/VCR selector button to select the
VCR mode.
When a TV is connected with an audio/video cable, turn
the TV and this VCR on and select the video input mode
on the TV.
TAPE SPEED AND
RECORDING/PLAYBACK TIME
You can select the two different tape speed before
recording.
1 Load a cassette tape with the
erase prevention tab intact.
The VCR will automatically
turn on.
VIDEO CASSETTE TAPE
TAPE SPEED
SP
Standard Play
T120
T160
2 Press the SPEED selector
button to select the desired
tape speed SP or SLP.
2 hours
2-2/3 hours
The counter and SP or SLP
will appear on the screen for
SLP
Super Long Play
6 hours
8 hours
about 4 seconds.
00 : 00 : 00 SP
This VCR selects the playback tape speed SP,
LP(Long Play) or SLP automatically.
18
4F21301A E P14-19
18
6/26/02, 3:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING A TV PROGRAM
"
" will appear on screen for about 4 seconds and the
VHF/UHF/CATV CHANNELS
REC indicator will blink to continue pause mode.
TV
CATV
VHF
2-13
VHF
2-13
NOTE: The pause function will be released after 5
minutes to prevent damage to the tape or the
VCR. The VCR will change to the STOP mode.
UHF
14-69
STD/HRC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100)(125)
01 (5A)
NOTE: AUTO REWIND FEATURE
This VCR will automatically rewind the tape
when the tape has ended (except during OTR
and TIMER REC). It will also eject the tape and
turn the VCR’s power OFF.
3 Press the direct channel selection buttons or the
CHANNEL Up or Down button to select the channel
to be recorded.
RECORDING ONE PROGRAM WHILE
WATCHING ANOTHER
While the VCR is recording, press the TV/VCR selector
button to select the TV mode.
The TV/VCR indicator will go off and recording will
continue.
Select the TV channel you want to watch by using the
TV channel selector.
1-9
Press 0 twice and then 1-9 as required.
Example: To select 2, Press “002”.
Press 0 first and then the remaining 2 digits in
order from left to right.
Example: Press 012 for “12”.
Press 2 digits in order.
10-12
13-99
Example: Press 22 for
CH 110
“22”.
100-125 Press the 3 digits in
NOTE: Some CATV hookups do not permit viewing one
channel while recording another. See pages 12
and 13.
order.
Example: Press 110
for “110”.
TO PREVENT AN ACCIDENTAL
RECORDING
After recording, break off the erase prevention tab if you
do not wish to record over the tape.
4 Press the REC/OTR button.
CH 110
"
" will appear on the screen
for about 4 seconds and the
REC indicator will light.
Screwdriver
NOTE: Since the VCR has its own TV tuner, it is not
actually necessary to have the TV turned on in
order to make a recording. Turning on the TV
merely allows confirmation of the proper channel
settings on your VCR.
TO STOP RECORDING
Press the STOP button to stop
recording.
Erase prevention tab
"
" will appear on screen for
about 4 seconds.
TO RECORD AGAIN
Cover the hole with adhesive tape.
Be careful the tape does not extend past the edges of
the cassette housing.
TO STOP RECORDING TEMPORARILY
Press the PAUSE/STILL button
to avoid recording unwanted
material. Press again or press
the REC/OTR button to continue
the recording.
Adhesive tape
19
4F21301A E P14-19
19
6/26/02, 3:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
ONE-TOUCH TIMER
SETTING THE TIMER
RECORDING
(
)
RECORDING OTR
The One-touch Timer Recording feature provides
a simple and convenient way to make a timed
recording.
Timer recording can be programmed on-screen with
the remote control. The built-in timer allows automatic
unattended recording of up to 8 programs within 1
month.
EXAMPLE: One-touch Timer Recording for 30 minutes.
EXAMPLE: Program a timer recording for the 26th day,
channel 125 (CATV), 11:00 - 11:30 PM on timer
program number 1 (Tape speed: SLP).
CHECK BEFORE YOU BEGIN
• Turn ON the TV and set to the video channel 3 or 4.
• Press the POWER button to turn the VCR on.
CHECK BEFORE YOU BEGIN
When a TV is connected with an audio/video cable, turn
the TV on and select the video input mode on the TV.
• Turn on the TV and set to the video channel 3 or 4.
• Press the TV/VCR selector button to select the VCR
mode.
• Load a video cassette with the erase prevention tab
intact. The VCR will automatically turn on.
• Check that the clock and date are correct (see page 15).
1 Load a cassette tape with the
erase prevention tab intact.
2 Press the SPEED selector
button to select the desired
tape speed SP or SLP.
When a TV is connected with an audio/video cable,
turn the TV and this VCR on and select the video input
mode on the TV.
The counter and SP or SLP
will appear on the screen for
about 4 seconds.
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
1 Press the MENU button.
Check the TIMER REC SET
00 : 00 : 00 SP
3 Press the direct channel
ON OFF
ON OFF
option is selected, then press
the ENTER button.
selection buttons or the
CH 125
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
CHANNEL Up or Down button
to select the channel to be
recorded.
2 Press the TRACKING SET + or
– button to select one of the
program lines, then press the
ENTER button.
+/–/ENTER/MENU
DATE START
END
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
CH
– –
– –
– –
– –
– –
– –
– –
– –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
–
–
–
–
–
–
–
–
The channel number will
appear on the screen for about
4 seconds.
3 Press the TRACKING SET +
or – button to select the date,
then press the ENTER button.
OTR 0 : 30
CH 125
4 Press the REC/OTR button to
〈
+ –
〉
/
/ENTER/CANCEL/MENU
begin recording. Press the
button again to stop recording
after 30 minutes. Each addi-
tional press of the REC/OTR
button will increase recording
time as shown in the chart
below, up to a maximum of 5
hours. The OTR and recording
time will appear on screen for
about 4 seconds.
4 Set the start time, end time,
channel and tape speed as in
step 3.
DATE
26(SU)
START END
CH
-
-:-- -:-- ---
------ -:-- -:-- ---
------ -:-- -:-- ---
------ -:-- -:-- ---
------ -:-- -:-- ---
------ -:-- -:-- ---
------ -:-- -:-- ---
------ -:-- -:-- ---
-
-
-
-
-
-
-
NOTE: To record from external
source, press the
TRACKING SET + or –
button and set the
channel to "L". "L" will
appear next to CH 125
(or 69).
〈
+/–/ENTER/CANCEL/MENU
〉
NOTES: • Press the REC/OTR
button to increase the once
Press
Recording time
NORMAL REC
0:30
5 To enter other programs,
repeat step 2 through 4. Or,
press the MENU button twice
to return to the normal screen.
time needed for
recording (See the
chart ).
• To cancel OTR, press
the STOP button or
turn off the power.
twice
3 times
4 times
5 times
6 times
7 times
8 times
1:00
1:30
6 Press the TIMER REC button.
The power will go off, the
T.REC indicator will light and
the VCR stands by for
recording.
2:00
3:00
4:00
5:00
9 times NORMAL REC
To cancel timer recording, press the button again and
the T.REC indicator will go out.
20
4F21301A E P20-25
20
6/26/02, 3:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE TIMER RECORDING
IF THE PROGRAM OVERLAPS
TO CORRECT THE SETTINGS
ANOTHER
When setting the Timer Recording, press the ENTER
button until the desired setting blinks, then re-enter the
setting using the TRACKING SET + or - button.
When finished, press the ENTER button.
NOTE: Do not overlap programs as portions of the
conflicting programs will be lost. The first
recording time has priority over the next recording
time as shown in the diagram.
NOTES: • The VCR cannot be used while the T.REC
indicator is lit.
8 : 00
9 : 00
10 : 00
11 : 00
Program 1
Program 2
• After a power failure or disconnection of the
power plug, all programmed recording
settings must be reset upon resumption of
power. In this case, reset the clock (see page
15) and reprogram any timer recordings.
• Press the CANCEL button to move cursor
backward for correction.
Deleted Parts
Program 3
Non Recorded Portion Parts
Prog.2
Recording
Control Settings
Prog.1
Prog.3
NOTES: • The everyday/every week recording can be
made continuously until the recording is
canceled or the tape reaches the end.
• During timer recording, the automatic
rewinding mechanism does not function.
TO SET DAILY/WEEKLY TIMER
When setting the date in step 3 in the Setting the Timer
Recording section on the previous page, press the
TRACKING SET – button repeatedly.
ON-SCREEN FUNCTION
DISPLAY
WHILE WATCHING TV
The setting changes as follows:
Press the CALL button.
EXAMPLE
DAY OF THE WEEK
The current day (Friday)
SU-SA (Sunday to Saturday)
CLOCK
8 : 30 AM THU
STEREO SAP
CH 125
CHANNEL
MO-SA (Monday to Saturday)
MO-FR (Monday to Friday)
WKL-TH (Weekly Thursday)
STEREO AND
SEPARATE AUDIO
PROGRAM (SAP)
One month later
minus one day
TAPE
00 : 00 : 00 SP
WKL-WE
(Weekly Wednesday)
SPEED
REAL TIME COUNTER
Press the CALL button again to make the display disappear.
TO CONFIRM THE SETTINGS
WHILE OPERATING A TAPE
Press the TRACKING SET + or
– button to select the TIMER
REC SET option in the MENU.
Then press the ENTER button to
display the timer program list.
Press the MENU button twice to
return to the normal screen.
DATE START
END
CH
Press the CALL button.
OPERATING MODE
(
)
26 WE 11:00PM 11:30PM 125SLP
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– –
– –
– –
– –
– –
– –
– –
–
–
–
–
–
–
–
8 : 30 AM THU
HI-FI
CH 125
HI-FI STEREO
AUTO REPEAT
〈
+ –
/
〉
/ENTER/CANCEL/MENU
TAPE IN
00 : 00 : 00 SP
Press the CALL button again to make the display disappear.
TO CANCEL A PROGRAM
TO SET THE COUNTER TO '00:00:00'
Press the COUNTER RESET button. The counter will
appear on the screen.
Press the TRACKING SET + or –
DATE START
END
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
CH
– –
– –
– –
– –
– –
– –
– –
– –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
–
–
–
–
–
–
–
–
button to select the TIMER REC
SET option in the MENU. Then
press the TRACKING SET + or –
button to select the unnecessary
program, and press the CANCEL
button to cancel the program.
NOTES: • If you rewind the tape from "00:00:00", a minus
sign ("–") will be displayed in front of the time.
• When you load a tape, the counter will change
to "00:00:00".
〈
+ –
/
〉
/ENTER/CANCEL/MENU
• The counter does not function on nonrecorded
(blank) sections of the tape. When you rewind,
fast forward or play tapes through blank sections,
the counter stops.
21
4F21301A E P20-25
21
6/26/02, 3:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
STEREO RECORDING
AND PLAYBACK
SEPARATE AUDIO
(
)
PROGRAM SAP
Your VCR is fitted with an SAP broadcast system
which enables you to switch to a SEPARATE AUDIO
PROGRAM when viewing a selected channel.
This function applies only when the program is
broadcast in multi-languages through the SAP
broadcast system.
RECORDING STEREO BROADCASTS
The VHS Hi-Fi audio system permits high fidelity
recording of MTS STEREO TV broadcasts.
When a MTS STEREO
broadcast is received, the
STEREO
CHECK BEFORE YOU BEGIN
STEREO will appear on the
screen and the program can
be viewed or recorded in
stereo (refer to pages 18 and
19 for recording procedures).
The Hi-Fi STEREO recording procedure is the same as
for normal recordings.
• Turn ON the TV and set to the video channel 3 or 4.
• Press the POWER button to turn the VCR on.
• Press the TV/VCR selector button to select the VCR
mode.
When a TV is connected with an audio/video cable, turn
the TV and this VCR on, and select the video input
mode on the TV.
NOTE: When using a CATV system, stereo TV programs
may be transmitted over a mono cable channel.
In this case the word “STEREO” will not appear
and the sound will be in mono.
MENU
CLOCK SET
TIMER REC SET
1 Press the MENU button.
AUTO REPEAT
CH SET UP
SAP
ON OFF
ON OFF
Press the TRACKING SET +
or – button to select the SAP
option.
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
〈+/–/ENTER/MENU〉
MENU
CLOCK SET
TIMER REC SET
2 Press the ENTER button to
OUTPUT SELECTION
select the ON position.
AUTO REPEAT
ON OFF
CH SET UP
When viewing an MTS STEREO TV program, or playing
a prerecorded VHS Hi-Fi STEREO videotape, press
AUDIO SELECT button to select how the audio will be
heard through the speakers. Normally set to the Hi-Fi
STEREO position, this button can be set to the MONO
position if the stereo broadcast or videotape audio is of
poor quality. The "R" and "L" positions allow the audio
from the Right or Left Hi-Fi channel to be heard over
both TV speakers. This button has no effect when
viewing a MONO videotape or TV program. Each time
when you press the button, OUTPUT SELECTION
display appears on the screen for several seconds.
Refer to the chart below.
SAP
ON OFF
LANGUAGE/IDIOMA/LANGUE
3 Press the MENU button again.
NO NOISE BACKGROUND
ON OFF
〈+/–/ENTER/MENU〉
LISTENING TO SAP
When the VCR is turned on or a channel selection is
made, make certain “SAP” appears on the screen. This
means that the "Separate Audio Program" broadcasting
is available.
STEREO SAP
SAP
OUTPUT
SOUND HEARD ON BOTH
SELECTION SPEAKERS
OR
STEREO
L CH
STEREO
LEFT CHANNEL AUDIO
RIGHT CHANNEL AUDIO
MONO
R CH
MONO
NOTES: • When playing back a tape that is not recorded
in Hi-Fi stereo mode, the audio will automati-
cally be monaural.
• When listening to a VHS Hi-Fi video tape or
MTS broadcast through the VHF/UHF jack
(Audio/Video cord not connected), the sound
will be monaural.
22
4F21301A E P20-25
22
6/26/02, 3:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
DUPLICATING A VIDEO TAPE
If you connect the VCR to another VCR or camcorder,
you can duplicate a previously recorded tape.
Make all connections before turning on the power.
3 Press the REC/OTR button on the recording VCR,
then press the PAUSE/STILL button.
4 Press the PLAY button on the playback VCR, then
press the PAUSE/STILL button.
1 Load a blank cassette tape with the erase prevention
tab intact into the recording VCR.
5 Press the PAUSE/STILL button on both the VCRs
Load a previously recorded tape into the playback
VCR or CAMCORDER.
simultaneously to begin the duplicating process.
LINE
NOTES: • It is recommended that you set the SPEED to
the SP mode on the recording VCR for best
results.
2 Press the INPUT SELECT
button to select AUDIO/VIDEO
input position. "LINE" will
appear on the screen.
• Unauthorized recording of copyrighted
television programs, films, video tapes and
other materials may infringe on the rights of
copyright owners and violate copyright laws.
Playback VCR
VIDEO HEAD CLEANING
To VIDEO OUT
To AUDIO (R) OUT
To AUDIO (L) OUT
VIDEO HEAD CLOGGING
AUDIO/VIDEO Cord (not supplied)
The video heads are the means by which the VCR
reads pictures from the tape during playback. In the
unlikely event that the heads become dirty enough to be
clogged, no picture will be played back. This can easily
be determined if, during playback of a known good tape,
there is good sound, but no picture (picture is extremely
snowy). If this is the case, use a high quality head
cleaning system or have them cleaned professionally.
Recording VCR
To VIDEO IN
To AUDIO (R) IN
To AUDIO (L) IN
VIDEO HEAD CLEANING
Playback Camcorder
Video head cleaning is needed when the playback
picture becomes unclear. This signifies that the heads
are getting dirty and can occur when playing poor quality
or damaged tapes. If the heads require cleaning, use a
equivalent high quality chemical non-abrasive (wet)
head cleaning tape or have them cleaned professionally.
If playing a head cleaning tape in the VCR once does
not improve the picture, play it several times before
requesting service.
To AV Jack
Recording VCR
To AUDIO (R) IN
To AUDIO (L) IN
DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR
SERVICE THE UNIT BY REMOVING THE TOP COVER.
To VIDEO IN
AUDIO/VIDEO Cord (not supplied)
NOTES: • Video heads may eventually wear out and
should be replaced when they fail to produce
clear pictures.
For duplicating a previously recorded tape from a
camcorder, follow the camcorder manufacturer’s
instructions. A typical camcorder dubbing hookup is
shown above.
• To help prevent video head clogging, use
only good quality VHS tapes. Discard worn
out tapes.
If the external unit you are connecting to the VCR
only has one audio output, then connect the output
to the L input on the VCR only.
23
4F21301A E P20-25
23
6/26/02, 3:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE REQUESTING SERVICE
Make sure by first checking the following points.
SYMPTOM
CAUSE
POSSIBLE SOLUTION
PAGE
POWER
Connect the AC power cord to the
AC outlet.
The AC power cord is not connected.
Cassette is not inserted.
No power.
5
Although the power is on, it
does not operate.
Insert a video cassette.
17
TV BROADCAST RECEPTION
Antenna connection is not correct.
Antenna cable is disconnected.
Connect it correctly.
10
10
Reconnect the antenna cable.
Set it to CH 3 or 4.
The video channel is not in the
correct position.
15
15
15
23
16
A TV program that is selected
by the VCR does not appear on
the screen.
The TV is not set to the video
channel 3 or 4.
Set the TV channel selector to the 3
or 4 position.
The TV/VCR selector is set at TV mode Press the TV/VCR selector button
(The TV/VCR indicator is not lit).
(The TV/VCR indicator will light).
INPUT SELECT is set to the LINE
mode.
Press the INPUT SELECT button to
select the TV mode.
A TV program selected by the
VCR does not appear in color.
Set the TV/CATV menu option to
select TV or CATV mode.
The TV/CATV menu option setting.
RECORDING
Place a piece of vinyl tape over the
gap.
The erase prevention tab of the video
cassette is broken off.
19
TV recording does not work.
Press the INPUT SELECT button to
select the TV mode.
INPUT SELECT is set to the LINE
mode.
23
15
20
Reset the present time.
Set the start/end time.
The time is not set correctly.
The recording start/end time is not set
correctly.
Timer recording does not work.
Press the TIMER REC button (The
T.REC indicator will light).
The TIMER REC button has not been
pressed (The T.REC indicator is not lit).
20
PLAYBACK
The TV is not set to the video channel Set to the video channel 3 or 4 or
No picture on screen when
15
21
3 or 4.
adjust the fine tuning button on your
TV set.
playing back a recorded tape.
Adjust tracking manually using the
AUTO TRACKING button or the
TRACKING SET + or – buttons on
remote control.
Tracking adjustment beyond range of
automatic tracking circuit.
Noise bars on screen.
Video heads are dirty.
Have the video heads cleaned.
Try another tape.
23
The tape is worn or damaged.
–
24
4F21301A E P20-25
24
6/26/02, 3:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMPTOM
CAUSE
POSSIBLE SOLUTION
PAGE
REMOTE CONTROL
It is not aimed at the remote sensor.
Aim it at the remote sensor.
6
6
Distance too far or too much light in
the room.
Operate within 15 feet (5 meters)
reduce the light in the room.
There is an obstacle in the path of
the beam.
Clear the path of the beam.
Remote control does not work.
6
6
6
The batteries are weak.
Replace the batteries.
Insert correctly.
The +, – polarity of the batteries are
not inserted correctly.
TV programs cannot be seen
using the TV selector.
The TV/VCR function is in the VCR
mode.
Set to TV, or turn off the VCR power
button.
–
SPECIFICATIONS
Video Head:
4 Rotary Heads
Hi-Fi Frequency Response: 100Hz to 10,000Hz at SP mode
Audio Track:
Hi-Fi Sound - 2 Tracks
MONO Sound - 1 Track
120V, 60Hz
Approx. 9 watts
181 Channel Freq. Synthesized
Hi-Fi Dynamic Range:
F.FWD/REW Time:
More than 90dB
F. FWD: Approx. 4minutes
and 50 seconds
REW: Approx. 2minutes and
30 seconds
Power Source:
Power Consumption:
Tuner:
VHF
UHF
CATV
2-13
14-69
(with T-120 Cassette Tape)
SP - 3 & 5 X Normal Speed
LP - 7 & 9 X Normal Speed
SLP - 9 & 15 X Normal Speed
14-3/16"W x 3-3/4"H x 9"D
7.1 Ibs
Infrared, Direct Access,
2 x AAA batteries (not supplied)
Remote Control
Speed Search:
14-36 (A)-(W)
37-59 (AA)-(WW)
60-85 (AAA)-(ZZZ)
86-94 (86)-(94)
95-99 (A-5)-(A-1)
100-125 (100)-(125)
01 (5A)
Dimensions:
Weight:
Remote Control:
Supplied accessories:
RF Channel Output:
Inputs/Outputs:
Video:
Channel 3 or 4, Switchable
75 ohm Coaxial Cable
In (RCA) 1Vp-p/75 ohm
Specifications are subject to change without notice.
Out (RCA) 1Vp-p/75 ohm
In (RCA)–8dB/50K ohm
Out (RCA)–8dB/1K ohm
UHF/VHF IN 75 ohm coaxial
UHF/VHF OUT 75 ohm coaxial
Audio:
Antenna:
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT OUR WEBSITE AT
WWW.MEMCORPINC.COM OR CONTACT CUSTOMER SERVICE AT 1-800-919-3647.
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN CASE YOU NEED TO RETURN THIS
PRODUCT TO YOUR PLACE OF PURCHASE OR MEMOREX.
FOR PARTS AND ACCESSORIES, CONTACT FOX INT'L AT 1-800-321-6993.
25
4F21301A E P20-25
25
6/26/02, 3:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
4F21301A E P20-25
26
6/26/02, 3:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
................................................................................................................
4F21301A E P20-25
27
6/26/02, 3:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Memcorp,Inc.
Weston,FL 33331
Printed in Thailand Impreso en Tailandia
4F21301B
02/04
U
4F21301B S P20-BACK
26
6/26/02, 3:57 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
|