Memorex MP3 Player MP3115 User Manual

MP3115  
User’s Guide  
Portable CD Player with  
AM/FM Stereo Radio  
Before operating this product,  
please read these instructions completely.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY PRECAUTIONS  
INFORMATION:  
This equipment has been tested and found to comply with the limits for a Class  
B digital device, pursuant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and  
on, the user is encouraged to try to correct the interference by one or more of  
the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which  
the receiver is connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT  
EXPOSE THIS UNIT TO RAIN OR MOISTURE.  
LASER SAFETY: This unit employs a laser. Only qualified service personnel  
should attempt to service this device due to possible eye injury.  
CAUTION: USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE  
PROCEDURE HEREIN MAY RESULT IN HAZARDOUS RADIATION  
EXPOSURE.  
SURGE PROTECTORS:  
It is recommended to use a surge protector for AC connection. Lightning and  
power surges ARE NOT covered under warranty for this product.  
ATTENTION:  
POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS  
LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISES  
ET POUSSER JUSQU’AU FOND.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003  
du Canada.  
Download from Www.Somanuals.com2. All Manuals Search And Download.  
Dear Customer:  
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of  
your musical enjoyment. Now it’s time to consider how you can maximize the fun and  
excitement your equipment offers. This manufacturer and the Electronic Industries  
Association’s Consumer Electronics Group want you to get the most out of your equip-  
ment by playing it at a safe level. One that lets the sound come through loud and clear  
without annoying blaring or distortion and, most importantly, without affecting your sensi-  
tive hearing.  
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes  
of sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard  
against this by setting your equipment at a safe level BEFORE your hearing adapts.  
To establish a safe level:  
• Start your volume control at a low setting.  
• Slowly increase the sound until you can hear it comfortably and clearly, and without dis-  
tortion.  
Once you have established a comfortable sound level:  
• Set the dial and leave it there.  
Taking a minute to do this now will help to prevent hearing damage or loss in the future.  
After all, we want you listening for a lifetime.  
We Want You Listening For A Lifetime  
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since  
hearing damage from loud noise is often undetectable until it is too late, this manufacturer  
and the Electronic Industries Association’s Consumer Electronics Group recommend you  
avoid prolonged exposure to excessive noise. This list of sound levels is included for your  
protection.  
Decibel  
Level  
30  
Example  
Quiet library, soft whispers  
40  
Living room, refrigerator, bedroom away from traffic  
Light traffic, normal conversation, quiet office  
Air conditioner at 20 feet, sewing machine  
Vacuum cleaner, hair dryer, noisy restaurant  
Average city traffic, garbage disposals, alarm clock at two feet  
50  
60  
70  
80  
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE:  
90  
Subway, motorcycle, truck traffic, lawn mower  
Garbage truck, chain saw, pneumatic drill  
Rock band concert in front of speakers, thunderclap  
Gunshot blast, jet engine  
100  
120  
140  
180  
Rocket launching pad  
EIA  
Information courtesy of the Deafness Research Foundation.  
EST. 1924  
We  
WantYou  
LISTENING  
ForALifetime  
Download from Www.Somanuals.com3. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
Before using the unit, be sure to read all operating instructions carefully. Please note that these are  
general precautions and may not pertain to your unit. For example, this unit may not have the capabili-  
ty to be connected to an outdoor antenna.  
1. READ INSTRUCTIONS  
All the safety and operating instructions should be read before the product is operated.  
2. RETAIN INSTRUCTIONS  
The safety and operating instructions should be retained for future reference.  
3. HEED WARNINGS  
All warnings on the product and in the operating instructions should be adhered to.  
4. FOLLOW INSTRUCTIONS  
All operating and use instructions should be followed.  
5. CLEANING  
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.  
Use a dry cloth for cleaning.  
6. ATTACHMENTS  
Do not use attachments not recommended by the product's manufacturer as they may cause hazards.  
7. WATER AND MOISTURE  
Do not use this product near water–for example: near a bathtub, washbowl, kitchen sink or laundry tub; in  
a wet basement; or near a swimming pool.  
8. ACCESSORIES  
Do not place this product on an unstable cart, stand, tripod, bracket or table. The product may fall, causing  
serious injury and serious damage to the product. Use only with a cart, stand, tripod, bracket or table rec-  
ommended by the manufacturer or sold with the product. Any mounting of the product  
should follow the manufacturer’s instructions, and should use a mounting accessory rec-  
ommended by the manufacturer.  
8A. An appliance and cart combination should be moved with care. Quick stops, excessive  
force and uneven surfaces may cause the appliance and cart combination to overturn.  
9. VENTILATION  
Slots and openings in the cabinet and in the back or bottom are provided for ventilation,  
to ensure reliable operation of the product and to protect it from overheating. These  
openings must not be blocked or covered. The openings should never be blocked by  
placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near  
or over a radiator or heat source. This product should not be placed in a built-in installation such as a  
bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been  
adhered to.  
10. POWER SOURCES  
This product should be operated only from the type of power source indicated on the marking label. If you  
are not sure of the type of power supply to your home, consult your appliance dealer or local power com-  
pany. For products intended to operate from battery power, or other sources, refer to the operating instruc-  
tions.  
11. GROUNDING OR POLARIZATION  
This product is equipped with a polarized alternating-current line plug (a plug having one blade wider than  
the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to  
insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your elec-  
trician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.  
12. POWER-CORD PROTECTION  
Power-supply cords should be  
routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying  
particular attention to cords at plugs, convenience receptacles, and the point where they exit from the  
appliance.  
13. LIGHTNING  
To protect your product from a lightning storm, or when it is left unattended and unused for long periods of  
time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage  
to the product due to lightning and power-line surges.  
14. POWER LINES  
An outside antenna system should not be located in the vicinity of overhead power lines or other electric  
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep from touching such power lines or circuits as con-  
tact with them might be fatal.  
Download from Www.Somanuals.com4. All Manuals Search And Download.  
SAFETY INSTRUCTIONS (CONTINUED)  
15. OVERLOADING  
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.  
16. OBJECT AND LIQUID ENTRY  
Never push objects of any kind into this product through openings as they may touch dangerous voltage points  
or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid on the product.  
17. OUTDOOR ANTENNA GROUNDING  
If an outside antenna is connected to the product, be sure the antenna system is grounded so as to pro-  
vide some protection against voltage surges and built-up static charges. Section 810 of the National  
Electric Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and sup-  
porting structure, grounding of the lead-in wire to an antenna discharge product, size of grounding conduc-  
tors, location of antenna discharge product, connection to grounding electrodes and requirements for  
grounding electrodes.  
18. SERVICING  
Do not attempt to service this  
product yourself as opening or  
removing covers may expose you  
to dangerous voltage or other  
hazards. Refer all servicing to  
qualified service personnel.  
19. REPLACEMENT PARTS  
When replacement parts are  
required, be sure the service tech-  
nician uses replacement parts  
specified by the manufacturer or  
those that have the same charac-  
teristics as the original part.  
Unauthorized substitutions may  
result in fire, electric shock or  
other hazards.  
20. SAFETY CHECK  
Upon completion of any service  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
or repairs to this product, ask the service technician to perform safety checks to determine that the product  
is in proper operating condition.  
21. WALL OR CEILING MOUNTING  
The product should be mounted to a wall or ceiling only as recommended by the manufacturer.  
22. DAMAGE REQUIRING SERVICE  
Unplug the product from the wall outlet and refer servicing to qualified service personnel under the follow-  
ing conditions:  
a. When the power-supply cord or plug is damaged.  
b. If liquid has been spilled or objects have fallen into the product.  
c. If the product has been exposed to rain or water.  
d. If the product does not operate normally by following the operating  
instructions. Adjust only those controls that are covered by the  
operating instructions, as an adjustment o other controls may result  
in damage and will often require extensive work by a qualified  
technician to restore the product to its normal operation.  
e. If the product has been dropped or the cabinet has been damaged.  
f.  
When the product exhibits a distinct change in performance–this  
indicates a need for service.  
23. HEAT  
The product should be situated away from heat sources such as radiators, heat registers, stoves or other  
products (including amplifiers) that produce heat.  
24. NOTE TO CATV SYSTEM INSTALLER  
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that  
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-  
nected to the grounding system of the building, as close to the point of cable entry as practical.  
Download from Www.Somanuals.com5. All Manuals Search And Download.  
LOCATION OF CONTROLS  
1. VOLUME Control  
15. CD OPEN/CLOSE Area  
16. TUNING Control  
2. BASS BOOST Button  
3. STOP (I) Button  
4. POWER ON Indicator  
5. Display  
17. AM/FM Dial Scale  
18. FM STEREO Indicator  
19. PLAY/PAUSE (®/p) Button  
20. PLAY/PROG(Program)Indicator  
21. Function Switch (CD/POWER  
OFF/FM/AM)  
6. BASS BOOST Indicator  
7. Left Speaker  
8. Skip/Search ( ) Button  
9. PROG (Program) Button  
10. REPEAT Button  
11. Battery Compartment  
(Bottom of Unit)  
12. FM Antenna  
13. CD Compartment  
14. Carrying Handle  
22. REPEAT Indicator  
23. AC Jack (Rear of Unit)  
24. Headphone Jack (Rear of  
Unit)  
25. Skip/Search ( ) Button  
26. Right Speaker  
Download from Www.Somanuals.com6. All Manuals Search And Download.  
POWER SOURCES  
This unit is designed to operate on AC household current or DC (batteries).  
AC  
Use the AC polarized line cord included with the unit for operation on AC power.  
Insert one end of the AC line cord into the AC jack on the rear of the unit and the  
other end (with the 2 blades) into a conveniently  
located AC outlet having 120V, 60Hz. When the  
AC cord is plugged in, the batteries will be discon-  
AC Outlet  
nected.  
NOTE: The AC plug supplied with the unit is polar-  
ized to help minimize the possibility of electric  
AC Plug  
shock. If the AC plug does not fit into a nonpolar-  
ized AC outlet, do not file or cut the wide blade. It is the user’s responsibility to have  
an electrician replace the obsolete outlet.  
BATTERY INSTALLATION  
To use this unit with battery power, remove the  
Battery Compartment door on the bottom of the  
unit by sliding it off. Insert eight (8) ‘C’ size  
batteries following the diagram in the  
compartment.  
NOTE: The AC power cord must be disconnected  
from the AC jack on the rear of the unit in order for  
the unit to operate on battery power.  
BATTERY PRECAUTIONS  
Follow these precautions when using batteries in this device:  
1. Use only the size and type of batteries specified.  
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.  
Reversed batteries may cause damage to the device.  
3. Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and Carbon-zinc) or old batteries  
with fresh ones.  
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from  
possible battery leakage.  
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery  
manufacturer’s directions.)  
HEADPHONE JACK  
For private listening, connect low impedance 3.5mm (32 ohm) stereo headphones  
(not included) to this jack. The speakers are automatically disconnected when the  
headphone plug is inserted in the jack.  
Download from Www.Somanuals.com7. All Manuals Search And Download.  
OPERATION  
LISTENING TO THE RADIO  
1
2
Slide the Function switch to the AM or  
FM position to turn the unit on and  
select AM or FM; the POWER ON  
indicator will light.  
Tune a desired station by turning the  
TUNING control.  
The frequencies are located on the  
AM/FM dial scale. If an FM Stereo sta-  
tion is broadcasting, the FM Stereo  
indicator will light.  
3
4
1
2
To turn the radio off, slide the Function  
switch to the POWER OFF position.  
Adjust the VOLUME control 1 and  
BASS BOOST button 2 as desired.  
Press the BASS BOOST button 2 to  
the “in” position to enhance the bass  
sound; the BASS BOOST indicator  
will light.  
ANTENNAS  
AM–This unit has a built-in ferrite rod antenna, which provides adequate reception in most  
areas. If reception is weak, turn the unit to improve reception.  
FM–The FM Antenna is for FM reception only. If reception is weak, adjust the length and the  
angle of the antenna.  
Download from Www.Somanuals.com8. All Manuals Search And Download.  
OPERATION (CONTINUED)  
TO PLAY A CD  
1
2
Slide the Function switch to the CD  
position to turn the unit on and select  
CD mode; the POWER ON indicator  
will light.  
Open the CD Compartment door by  
pressing the OPEN/CLOSE area. Place  
a CD on the center spindle, with the  
printed label side facing up. Close the  
CD Compartment door; the total tracks  
will appear in the display.  
3
4
3
1
2
To play a disc from the beginning, press the  
PLAY/PAUSE (®/p) button; the PLAY/PROG  
indicator will light.  
Press the PLAY/PAUSE (®/p) button again to  
pause playback; the track number will blink and  
the PLAY/PROG indicator will turn off. Press the  
PLAY/PAUSE (®/p) button once again to contin-  
ue playback; the track number will stop blinking  
and the PLAY/PROG indicator will light.  
To start from a specific track,  
while in the stop mode, locate the  
track using the Skip/Search o 1 or n 2  
button, then, within five seconds, press  
the PLAY/PAUSE (®/p) button 3 to start  
playback from the track selected. The  
PLAY/PROG indicator will light.  
5
1
6
2
1
2
To skip forward or backward through the tracks  
on the disc, press the Skip/Search o 1 or n 2  
button.  
Adjust the VOLUME control 1 and  
BASS BOOST button 2 as desired.  
Press the BASS BOOST button 2 to  
the “in” position to enhance the bass  
sound; the BASS BOOST indicator  
will light.  
To search forward or backward through the play-  
ing track, press and hold the Skip/Search o 1 or  
n 2 button; a chattering noise will be heard. Stop  
pressing the button to return to normal playback.  
CONTINUED ON THE NEXT PAGE  
Download from Www.Somanuals.com9. All Manuals Search And Download.  
OPERATION (CONTINUED)  
TO PLAY A CD (CONTINUED)  
7
8
When the disc is through playing, it will  
stop rotating. Press the STOP (I) but-  
ton to stop the disc before it is finished.  
To turn the unit off, slide the Function  
switch to the POWER OFF position.  
NOTES:  
• If there is no disc or a disc is inserted incorrectly, dirty or damaged, "Er" or "no" will  
appear in the display.  
• As each track is played, the track number is shown in the display.  
To prevent damage to the disc, never open the CD door while the disc is rotating. Wait  
for the disc to stop before opening the CD door. Never touch the lens when the CD  
door is open.  
• DO NOT use the carrying handle when playing a CD. The CD should only be used  
on a steady surface.  
TO REPEATEDLY PLAY BACK ONE TRACK/ALL TRACKS  
1
2
4
2
2
1
1
To repeat a single track, press the REPEAT  
button 1 once while in the Stop mode; the  
Repeat indicator will blink. Press the  
Skip/Search o 2 or n 3 button to select the  
specific track that you wish to repeat. When  
the desired track number appears in the  
display, within five seconds, press the  
PLAY/PAUSE (®/p) button 4 to begin  
playback. The PLAY/PROG indicator will light  
and the specific track you selected will be  
repeated continuously.  
To repeat all of the tracks on a disc  
continuously, press the REPEAT  
button 1 twice while in the Stop mode;  
the Repeat indicator will light. Press the  
PLAY/PAUSE (®/p) button 2 to begin  
playback. The PLAY/PROG indicator  
will light and all tracks will be repeated  
continuously.  
To cancel Repeat playback, press the STOP (I) button twice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
OPERATION (CONTINUED)  
TO PROGRAM THE MEMORY (UP TO 20 TRACKS)  
1
2
Slide the Function switch to the CD  
position to turn the unit on and select  
CD mode; the POWER ON indicator  
will light. Insert a CD as described on  
page 9.  
Press the PROGRAM button; “01” on  
the display and the PLAY/PROG indi-  
cator will blink.  
3
4
1
2
Press the PROGRAM button again;  
the selected track has now been pro-  
grammed and counted as program 1.  
Use the Skip/Search o 1 or n 2 but-  
ton to select the first track to be pro-  
grammed.  
5
6
1
2
Repeat steps 3 and 4 to program the other  
desired tracks in sequence.  
When the program memory is full, the unit  
will run through the programmed tracks in  
the display and then revert to “01”.  
Press the PLAY/PAUSE (®/p) button to  
begin Programmed playback; the  
PLAY/PROG indicator will blink and the  
tracks will play in the order programmed.  
SEE NEXT PAGES FOR NOTES ON PROGRAMMED PLAY  
Download from Www.Somanuals.co1m1. All Manuals Search And Download.  
OPERATION (CONTINUED)  
NOTES ON PROGRAMMED PLAY:  
Programming is the ability to preselect the order in which a series of tracks  
will be played.  
Each track may be stored in the program memory as many times as desired.  
As each track is played, its track number will be displayed. You can move for-  
ward or backward through the programmed tracks with the Skip/Search o or  
n button.  
The CD player will stop after all programmed tracks have been played or the  
STOP (I) button is pressed.  
The Program memory will be cleared when the STOP (I) button is pressed  
twice, the unit is turned off or changed to another mode or when the CD door  
is opened.  
To check the program, while in the Stop mode, press the PROGRAM button  
and the unit will run through the programmed tracks in the display and then  
revert to “01”.  
PROGRAMMED REPEAT  
1
2
It is also possible to use the Program and  
Repeat functions together to repeat a  
specific program indefinitely. First,  
program the tracks you wish to hear in the  
order you wish to hear them, as described  
on page 11. Then, press the REPEAT  
buttontwice. ThePLAY/PROGindicatorwill  
blink and the REPEAT indicator will light.  
Press the PLAY/PAUSE (®/p) button  
to begin Programmed Repeat  
playback; the PLAY/PROG indicator  
will continue to blink and the REPEAT  
indicator will light. The player will play  
the tracks you selected in the order in  
which you programmed them. When  
the last track in the program has been  
played, the entire program will begin  
again.  
NOTE:  
Program Repeat operation will continue indefinitely until you press the STOP (I)  
button. Press the STOP (I) button again to cancel both Program and Repeat.  
Download from Www.Somanuals.co1m2. All Manuals Search And Download.  
CARE AND MAINTENANCE  
Caring for Compact Discs  
• Treat the compact disc carefully. Handle the com-  
pact disc only by its edges. Never allow your  
fingers to come in contact with the shiny, unprint-  
ed side of the compact disc.  
• Do not attach adhesive tape, stickers, etc. to  
the disc label.  
• Clean the compact disc periodically with a soft, lint-free, dry cloth. Never use deter-  
gents or abrasive cleaners to clean the compact disc. If necessary, use a CD clean-  
ing kit.  
• If a disc skips or gets stuck on a sec-  
tion of the compact disc, it is probably  
dirty or damaged (scratched).  
• When cleaning the compact disc,  
wipe in straight lines from the center  
of the compact disc to the outer edge  
of the compact disc. Never wipe in  
circular motions.  
• This unit is designed to play only compact discs bearing the identifica-  
tion logo as shown here. Other discs may not conform to the CD stan-  
dard and may not play properly.  
• Compact discs should be stored in their cases after each use to avoid damage.  
• Do not expose compact discs to direct sunlight, high humidity, high temperatures or  
dust, etc. Prolonged exposure or extreme temperatures can warp the compact disc.  
• Do not stick or write anything on either side of the compact disc. Sharp writing  
instruments, or the ink, may damage the surface.  
Cleaning the Unit  
To prevent fire or shock hazard, disconnect your unit from the AC power source  
when cleaning.  
• The finish on your unit may be cleaned with a dust cloth and cared for as other fur-  
niture. Use caution when cleaning and wiping the plastic parts.  
• Mild soap and a damp cloth may be used on the front panel.  
Download from Www.Somanuals.co1m3. All Manuals Search And Download.  
TROUBLESHOOTING GUIDE  
If you experience a problem with this unit, check the chart below before calling for  
service.  
SYMPTOM  
Unit will not  
turn on.  
CAUSE  
AC cord not  
connected.  
SOLUTION  
Check AC cord  
connection.  
Disc will not play.  
CD Compartment  
door not closed.  
Disc inserted  
incorrectly.  
Close CD Compartment  
door.  
Reinsert disc correctly.  
Dirty or defective CD. Try another disc.  
Moisture  
Wipe disc with soft cloth.  
condensation on disc.  
VOLUME control  
set to minimum.  
Defective disc.  
Dirty or defective  
disc.  
No sound.  
Increase volume.  
Try another disc.  
Clean or replace disc.  
Erratic playback.  
AM or FM, no sound. Power is not on.  
Slide the FUNCTION  
switch to AM or FM.  
Increase volume.  
Retune the AM or FM  
broadcast station.  
Reorient FM  
Volume set too low.  
AM/FM, poor sound. Station is not tuned  
properly.  
FM: Antenna is not  
properly adjusted.  
antenna.  
AM: Unit is not pos-  
itioned correctly.  
Rotate unit until best  
reception is obtained.  
Download from Www.Somanuals.co1m4. All Manuals Search And Download.  
SPECIFICATIONS  
GENERAL:  
Power Source ..............................................................................120V, 60Hz AC  
Battery...........................................................DC 12V, 8 x 1.5V ‘C’ size batteries  
Alkaline is recommended for longer life  
Speaker.....................................................................................................2 x 2W  
Output Power .........................................................................................2 x 1.2W  
Dimensions ......................................................11.3 (W) x 9 (D) x 5.5 (H) Inches  
Weight..........................................................................................................4 Lbs  
RADIO SECTION:  
Frequency Range (FM)....................................................................88–108 MHz  
Frequency Range (AM) ................................................................530–1710 kHz  
CD SECTION:  
Disc Diameter ...............................................................................4.72" (120mm)  
3.15" (80mm) Single CD  
Optical Source....................................................................Semiconductor Laser  
Specifications are subject to change without notice.  
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE  
VISIT OUR WEBSITE AT WWW.MEMOREXELECTRONICS.COM OR CON-  
TACT CUSTOMER SERVICE AT (954) 660-7100.  
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN  
CASE YOU NEED TO RETURN THIS PRODUCT TO YOUR PLACE OF  
PURCHASE OR MEMOREX.  
FOR PARTS AND ACCESSORIES, CONTACT FOX INTERNATIONAL AT  
1-800-321-6993.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
Memcorp, Inc.  
Weston, FL  
Printed in Hong Kong  
Download from Www.Somanuals.com. All Manuals Search And Download.  

KTM Motorcycle Accessories 450 XC ATV 2008 User Manual
LaCie Computer Drive Starck Desktop User Manual
Lenmar Enterprises Battery Charger 36 Volt User Manual
LG Electronics Clothes Dryer D8388 User Manual
Lindy Switch 32320 User Manual
Maytag Washer LAT9904 User Manual
Metabo Grinder 600160420 User Manual
Metrologic Instruments Scanner MS700i User Manual
MicroNet Technology Network Router MaxNAS User Manual
Midland Radio Two Way Radio GXT500 GXT550 GXT565 User Manual