OWNER'S MANUAL
MANUAL DE INSTRUCCIONES
DVD PLAYER/Hi-Fi VIDEO CASSETTE RECORDER
DVD COMPACTOS/VIDEOGRABADOR Hi-Fi ESTEREO
MVD4540B
ATTENTION
ATENCION
If you purchase a universal remote control from your local retailer, please contact
the remote manufacturer for the required programming code.
Si usted a comprado un control de remoto universal, por favor comunicace con el
fabricante para el codico de programaccion requerido.
TV/CATV MODE SELECTION
SELECCION DE MODO DE TV/CATV
When shipped from the factory, the TV/CATV menu option is set to the "CATV"
(Cable Television) mode.
If not using CATV (Cable TV), set this menu option to the "TV" mode.
A la salida de fábrica, la opción de menú TV/CATV está en el modo "CATV" (televisión
por cable).
Si no se va a utilizar el CATV (TV cable), cambie la opción de este menú al modo TV.
Before operating the unit, please read this manual thoroughly.
Antes de utilizar su aparato favor de leer las siguientes instrucciones.
2C51001AE Cover
1
18/11/03, 2:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the unit is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the unit and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning the exterior cabinet only.
6. ATTACHMENTS
The manufacturer of this unit does not make any recommendations for attachments, as they may cause
hazards.
7. WATER AND MOISTURE
Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.
PORTABLE CART WARNING
(symbol provided by RETAC)
8. ACCESSORIES
Do not place this unit on an unstable cart, stand, tripod, bracket, or table.
The unit may fall, causing serious injury, and serious damage to the unit.
8A. An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.
9. VENTILATION
Slots and openings in the cabinet back or bottom are provided for ventilation,
to ensure reliable operation of the unit, and to protect it from overheating.
S3125A
These openings must not be blocked or covered. The openings should never be blocked by placing the unit
on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat
source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided and/or the manufacturer’s instructions have been adhered to.
10. POWER SOURCES
This unit should be operated only from the type of power source indicated on the rating plate. If you are not
sure of the type of power supply to your home, consult your appliance dealer or local power company. For
units intended to operate from battery power, or other sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug, if your unit is equipped
with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a ground-
ing-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact
your electrician to replace your obsolete outlet.Do not defeat the safety purpose of the grounding-type plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
3
2C51001AE (02-05)
3
18/11/03, 2:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
13. LIGHTNING
To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the
unit due to lightning and power line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits, as
contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is
grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the
National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for
the grounding electrode.
18. SERVICING
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
19. DAMAGE REQUIRING SERVICE
Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions, as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the
unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f. When the unit exhibits a distinct change in performance, this indicates a need for service.
20. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
21. SAFETY CHECK
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.
22. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
23. DISC TRAY
Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.
24. CONNECTING
When you connect the product to other equipment, turn off the power and unplug all of the equipment from
the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's
manual of the other equipment carefully and follow the instructions when making any connections.
4
2C51001AE (02-05)
4
18/11/03, 2:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS / Power Source
25. LASER BEAM
Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the
laser beam. It may cause sight damage.
26. DISC
Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious
personal injury and product malfunction.
27. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-
nected to the grounding system of the building, as close to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
NATIONAL ELECTRICAL CODE
ANTENNA LEAD IN WIRE
ANTENNA
GROUND CLAMP
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC SERVICE
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC-NATIONAL ELECTRICAL CODE
S2898A
CONDENSATION
Moisture will form in the operating section of the DVD/VCR if the player is brought from cool surroundings into a
warm room or if the temperature of the room rises suddenly. When this happens, the DVD/VCR's performance
will be impaired.
To prevent this, let the DVD/VCR stand in its new surroundings for about an hour before switching it on, or
make sure that the room temperature rises gradually.
Condensation may also form during the summer if the DVD/VCR is exposed to the breeze from an air
conditioner. In such cases, change the location of the DVD/VCR.
Power Source
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for operation on AC. Insert
AC Outlet
the AC cord plug into a standard 120V 60Hz polarized AC outlet.
Wider Hole
and Blade
NOTES:
Never connect the AC line cord plug to other than the specified
voltage (120V 60Hz). Use the attached power cord only.
If the polarized AC cord does not fit into a non-polarized AC
outlet, do not attempt to file or cut the blade. It is the user’s
responsibility to have an electrician replace the obsolete outlet.
If you cause a static discharge when touching the unit and the
unit fails to function, simply unplug the unit from the AC outlet
and plug it back in. The unit should return to normal operation.
•
•
•
Polarized AC Cord Plug
(One blade is wider than the other.)
5
2C51001AE (02-05)
5
18/11/03, 2:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
DVD/CD Player/Video Cassette Recorder
• DVD/CD player withVideo Cassette Recorder - Unique space saving design combines a DVD/CD player and a Hi-Fi Video
cassette recorder.The DVD disc has much more capacity, but is the same size as the audio CD disc. Picture quality is higher
than Super VHS. Audio quality is higher than audio CD. The DVD PLAYER can play back audio CDs.
• High Quality Picture - More than 500 lines (VCR mode: 230 lines) of Horizontal Resolution. It exceeds Super VHS (400
lines) or Laser Disc (430 lines) in resolution.
VCR Section
• Stereo/SAP Reception - This VCR is designed to receive stereo and second audio program (SAP) broadcasts where
available.
• 4 Video Heads - Provides optimal picture quality for special effects playback.
• 19µm HEAD - For superior picture quality even in SLP mode, 19micron width technology helps to avoid crosstalk and
boost SLP picture quality to near SP levels. With precision technology, ghosts and color beats are virtually eliminated.
• Hi-Fi Stereo Sound - With a frequency response of 20 to 20,000 Hz and a dynamic range of better than 90dB, this VCR
provides a level of excellence that rivals compact discs.
• One-touch Timer Recording (OTR) - Simply by pressing the REC/OTR button, the VCR can be programmed for up to 6
hours of recording with an immediate start.
DVD Section
• Compatible with a wide range of DVD audio outputs
Digital Audio Jack (Optical or Coaxial):
• When a component with a built-in Dolby Digital decoder is connected, Dolby Digital sound can produce the effect of
being in a movie theater or a concert hall.
• Surround standard different from Dolby Digital. This format is already in use in many theaters. By connecting this unit
to a DTS decoder or an AV amplifier with a built-in DTS decoder, the DTS audio of DVD discs recorded in this format
can be enjoyed. However, audio will not be output from the analog audio output jacks.
• The MPEG audio of DVD discs recorded in this format can be enjoyed.
• The Linear PCM sound of a 48 kHz/16 bit through 96 kHz/24 bit exceeds audio CD sound.
• Progressive scan - Progressive scan displays all the horizontal lines of a picture at one time, as a single frame. This
unit converts the interlaced (480i) video from DVD into progressive (480p) format for connection to a progressive
display. It increases the vertical resolution.
• Multi-Language - Since this DVD matches with 124 language-subtitles/-soundtracks, you can enjoy selecting a favorite
one. (You can not select the language that is not recorded on the disc.)
• Multi-Angle - Pictures of Sports or a Live Concert are recorded with many cameras. When you play such a disc, you
can change the angles during playback. (If a Multi-Angle is not recorded on the disc, you can not change the angle.)
• Repeat Playback - You can repeat chapter, track, title, sides or material between two selected points.
• Program/Random Playback (CD) - You can play back tracks in programmed or random-selected sequences.
• Zoom - You can zoom in on the selected subject on the screen during playback.
• Video Aspect Ratio - You can change the aspect ratio of the screen for your monitor/television on a suitable disc.
• Parental Control - You can limit the playback of scenes or sounds of adult DVD discs which have a parental level rating.
* This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents
and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision Corporation and is intended for home and other limited
viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is
prohibited.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
*
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
*
* Unauthorized recording of copyrighted television programs, films, video cassettes and other materials may infringe the
rights of copyright owners and be contrary to copyright laws.
6
2C51001AE (06-11)
6
18/11/03, 2:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Before using your unit
Disc playback operation
IMPORTANT SAFEGUARDS ..........................3
Power Source...................................................5
Features ...........................................................6
Contents ...........................................................7
Parts and functions ..........................................8
Display .............................................................9
Remote control ...............................................10
Basic connections ..........................................12
CATV (CABLE TV) connections.....................14
Playback connection ......................................16
Disc ................................................................ 33
Setting setup language .................................. 34
Playback procedure........................................ 35
Special playback ............................................ 36
Zooming ......................................................... 37
Locating desired scene .................................. 37
Repeat playback............................................. 38
Program playback/Random playback (CD) .... 39
MP3 playback................................................. 40
Marking desired scenes ................................. 41
Changing soundtrack language ..................... 42
Subtitles ......................................................... 42
Karaoke playback ........................................... 42
Changing angles ............................................ 43
Title selection ................................................. 43
DVD menu...................................................... 43
Setting up the VCR section
Setting the video channel............................... 18
Setting the language ...................................... 18
Manual clock setting....................................... 19
Tuner setting................................................... 20
To ADD/DELETE channels ............................ 21
Noise elimination ............................................ 21
Loading and Unloading a cassette tape......... 22
Advanced function of DVD section
Parental control .............................................. 44
Temporary disabling of rating level by DVD disc ... 45
Setting menu language .................................. 46
Setting subtitle language................................ 47
Setting audio soundtrack language ................ 48
Setting the aspect ratio of TV screen ............. 49
Setting on screen display ............................... 50
Status display of disc ..................................... 50
Dynamic Range Control ................................. 51
Progressive scan............................................ 52
Tape playback operation
Cassette tape playback .................................. 23
Special playback ............................................ 24
ZERO RETURN function................................ 25
Video index search system ............................ 25
Recording
Recording a TV program ................................ 26
One-touch Timer Recording (OTR) ................ 28
Timer recording .............................................. 29
Additional information
Language code list ......................................... 53
Problems and troubleshooting ....................... 54
Video head cleaning....................................... 55
Specifications ................................................. 56
Advanced function of VCR section
Stereo recording and playback ...................... 31
Second Audio Program (SAP)........................ 31
Duplicating a video tape................................. 32
7
2C51001AE (06-11)
7
18/11/03, 2:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and functions
Front
VCR/DVD mode selector button
Cassette Loading Slot
PLAY button
OPEN/CLOSE button STOP button
Disc tray
EJECT button
POWER
Display window
REW (Rewind) button
DVD indicator
CHANNEL
buttons
/
POWER button
REC/OTR button
FF (Fast Forward) button
Remote sensor
AUDIO (L/R)/
VIDEO IN jacks
VCR indicator
Rear
DVD COAXIAL DIGITAL
AUDIO OUT jack
AC power cord
RF IN jack
RF OUT jack
DVD S-VIDEO
OUT jack
DVD AUDIO (L/R)
OUT jacks
S-VIDEO/COMPONENT DVD OPTICAL DIGITAL
Video selector switch AUDIO OUT jack
DVD/VCR common AUDIO (L/R)/
VIDEO OUT jacks
DVD COMPONENT OUT jacks
8
2C51001AE (06-11)
8
18/11/03, 2:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Display
Display window
1
2
3
4
12
5
6
11
10
9
8
7
No. Display
Description
1
2
3
4
5
6
VCR
VCR mode
Playback (lights) / Auto resume (flashes)
Still picture
DVD disc is inserted.
DVD
CD
CD is inserted.
PM
Display for afternoon (lights out in the morning)
Clock display (colon[ : ] flashes)
10 : 00
01 : 00
2
Counter display by hour/minute at VCR/DVD / by minute/second at CD
Track number display for CD
7
TV channel display for VCR
CH02
C036
CATV channel display
External input display
Error display
L
Err
Progressive scanning mode
8
9
Timer recording display
10
11
12
Video tape is in the unit
Track display for CD
TRK
REC
Normal recording display (flashes during One-touch Timer Recording - OTR)
NOTE:
Some discs may be displayed wrong or e.g. chapter number, playback time, etc. may not be displayed.
9
2C51001AE (06-11)
9
18/11/03, 2:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
Page
18
POWER
EJECT
Power on/off
Eject a cassette tape
Open or Close the tray
Switch to operate VCR or DVD
Direct channel selection of TV
Input setting
22
OPEN/CLOSE
VCR/DVD
0-9
35
18,34
21,26,28
37,39
44,45
27,50
Enter a password
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
DISPLAY/CALL
INPUT SELECT
PROGRESSIVE
Display VCR or DVD operation status
Switch the connected TV to external mode
32
DISPLAY/CALL
1
4
7
2
5
8
3
6
Set the progressive scanning mode to active 52
Select channel of the connected TV or VCR
26,28
CH
/
INPUT SELECT/
PROGRESSIVE
/
Cursor buttons
TRACKING/SET –/+ Setting buttons
Manual tracking buttons in playback mode
Cursor buttons
34
9
0
29,30
24
CH
/
18
SELECT/ENTER Enter information in the menu
Select option in the menu
18
TRACKING/
SET
–
TRACKING/
SET
+
34
SELECT/
ENTER
DVD MENU
Select menu of a DVD disc
43
18,34,44,46-51
30
SETUP/VCR MENU Display menu of setup
CLEAR/CANCEL Delete Timer program
CH
Cancel input data in the setting mode 19,29,37,39
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
RETURN
MARKER
ZOOM
Remove DVD setup menu
Index for DVD
34
41
37
43
MARKER
ZOOM
TOP MENU REPEAT A-B
Zoom (for DVD playback)
Select title of a DVD disc
TOP MENU
REPEAT A-B
AUDIO/
JUMP/
ANGLE/
CLOCK/
Repeat playback between A and B (DVD/CD) 38
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
AUDIO/AUDIO SELECT Switches sound between mono and stereo
Change soundtrack language of DVD
31
42
37
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
JUMP
Locating desired scene
REW/SEARCH
PLAY
SEARCH/F.FWD
ZERO RETURN
ANGLE
Stop the tape when the counter reaches 00:00 25
Change playback angle of a DVD disc
43
25
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
COUNTER RESET Reset the counter to 00:00
CLOCK/COUNTER Change the front Display mode
25
SLOW
PAUSE/STILL
TIMER REC
SUB TITLE
ATR
Set the unit to start recording at a preset time
.
29,30
42
Set Subtitle of a DVD disc
Digital AUTO TRACKING
Select playback mode
24
PLAY MODE
SPEED
38,39
26,28
18,27
Sets the tape speed for recording
Switches between TV and VCR
Rewind/Review playback
Playback
TV/VCR
REW/SEARCH
PLAY
23,24,36
23,35
F.FWD/SEARCH
Fast Forward/Forward search playback 23,24,36
SKIP
/
Skip chapter to forward or reverse direction
Search for the INDEX mark of a tape
Stop
36
25
INDEX +/–
STOP
23,35
REC/OTR
SLOW
Recording
26,28,32
24,36
Slow-motion playback
PAUSE/STILL
Still picture/Recording pause on/off 24,27,32,36
10
2C51001AE (06-11)
10
18/11/03, 2:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
Inserting Batteries
Open the battery
compartment cover in the
direction of the arrow.
Install two “AAA” batteries (not
supplied), paying attention to the
polarity diagram in the battery
compartment.
Replace the compartment
cover.
1
2
3
Battery precautions
The precautions below should be followed when using batteries in this device:
1.Use only the size and type of batteries specified.
2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.
3.Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery
manufacturer’s directions.)
Remote control basics
• Press POWER to turn the DVD/VCR on or off.
• Press CH or CH to move through the channels one channel at a time.
• The CH
/
and SET +/– are also used to navigate on-screen menu system.
• You can directly access specific channels using Number keys pad.
• Each press of VCR/DVD on the remote control, switches the screen between the VCR screen (VCR mode)
and the DVD screen (DVD mode).
Operation
• Aim the remote control at the remote sensor and press control buttons
to operate.
• Operate the remote control within 30° angle on either side of the remote
sensor, up to a distance of Approx. 5 meters.
Approx. 5 meters
11
2C51001AE (06-11)
11
18/11/03, 2:37 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic connections
If you are using an antenna system, follow these instructions. If you are a cable (CATV) subscriber, skip
ahead to page 14 for the proper connections.
ANTENNA TO DVD/VCR CONNECTION
The DVD/VCR must be connected “between” the antenna and the TV. First, disconnect the antenna from the TV
and connect it to the DVD/VCR.Then connect the DVD/VCR to theTV.Below are 3 common methods of connecting
an antenna system to a DVD/VCR. Find the type of antenna system you are using and follow the connection
diagram.
Combination VHF/UHF Antenna with 75 ohm Coaxial Cable
DVD/VCR
1
IN
(ANT)
75 ohm Coaxial Cable
OUT
(TV)
Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire
2
3
DVD/VCR
Matching Transformer
300 ohm Input
IN
(ANT)
75 ohm output
(not supplied)
OUT
(TV)
300 ohm Twin Lead (Flat) Wire
DVD/VCR
Separate VHF and UHF Antennas
Combiner
75/300 ohm Inputs
75 ohm output
(not supplied)
UHF
VHF
IN
(ANT)
300 ohm Twin Lead (Flat) Wire
OUT
(TV)
75 ohm Coaxial Cable
NOTE: If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300
ohm inputs and one 75 ohm output.
NOTES: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the
antenna to the DVD/VCR properly.
• For better quality recording, an indoor antenna or a telescopic antenna is not recommended.The use of
an outdoor type antenna is required.
• If you are not sure about the connection, please refer to qualified service personnel.
12
2C51001AE (12-15)
12
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic connections
DVD/VCR TO TV CONNECTION
After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow
the connection diagram.
This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna
inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.
TV
NOTE: If a VHF or UHF antenna is
used, set the TV/CATV
menu option to the “TV”
mode.
VHF/UHF IN
75 ohm Coaxial Cable (supplied)
TV with single 75 ohm VHF/UHF
antenna input
TV
NOTE: If a VHF or UHF antenna is
Splitter
75 ohm Input
75/300 ohm outputs
(not supplied)
used, set the TV/CATV
menu option to the “TV”
mode.
UHF
VHF
75 ohm Coaxial Cable
(supplied)
TV with 300 ohm UHFand 75 ohm VHF
antenna inputs
TV
NOTE: If a VHF or UHF antenna is
used, set the TV/CATV
menu option to the “TV”
mode.
UHF
Splitter
75 ohm Input
300 ohm outputs
(not supplied)
75 ohm Coaxial Cable
(supplied)
VHF
TV with 300 ohm UHF and 300 ohm VHF
antenna inputs
13
2C51001AE (12-15)
13
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
CATV (CABLE TV) connections
Many cable companies offer services permitting reception of extra channels including pay or subscription channels.
This DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable
company supplied converter box, except for those channels which are intentionally scrambled. If you subscribe to
a special channel which is scrambled, you must have a descrambler box for proper reception.
DVD/VCR
1
TV
IN
(ANT)
VHF/UHF
IN (ANT)
Incoming Cable
OUT
(TV)
ALLOWS: Recording of nonscrambled channels.
*
*
*
Use of the programmable timer.
Recording of one channel while watching another.
DVD/VCR
2
Converter/
Descrambler
TV
IN
(ANT)
VHF/UHF
IN (ANT)
Incoming
Cable
OUT
(TV)
ALLOWS: Recording of channels through the converter box
*
(scrambled and unscrambled).
Using the programmable timer to record only the
channel selected at the converter box.
NOTE:
To record from converter/descrambler,
DVD/VCR tuner must be tuned to the
converter output channel, usually
channel 3 or 4.
*
PREVENTS: Recording one channel while watching another.
*
*
Using the DVD/VCR tuner to select channels.
DVD/VCR
3
TV
IN
(ANT)
VHF/UHF
IN (ANT)
Converter/Descrambler
Incoming Cable
OUT
(TV)
NOTE:
ALLOWS: Recording of nonscrambled channels.
*
If you are playing a tape or using the
Use of the programmable timer.
Recording an unscrambled channel while watching
any channel selected at the converter box.
*
*
tuner built into the DVD/VCR, the
converter must be set to the video
channel output of the DVD/VCR (either
3 or 4).
PREVENTS: Recording scrambled channels.
NOTE: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR
to the output of the Converter/Descrambler box, usually channel 3 or 4.
14
2C51001AE (12-15)
14
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
CATV (CABLE TV) connections
IMPORTANT: Make sure the TV/CATV menu option is set to the “CATV” mode.
This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler.In order to receive scrambled
programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult
your local cable company for more information concerning connection to their descrambler equipment. There are many
ways to connect your DVD/VCR to a cable system. Below are six common methods of connection.
DVD/VCR
TV
Splitter
4
A/B Switch
VHF/UHF
IN (ANT)
IN
(ANT)
Incoming
A
Cable
OUT
(TV)
B
Converter/Descrambler
ALLOWS: Recording of one channel while watching another.
*
*
*
Using the programmable timer to record only the channel selected at the converter box.
Recording of all channels through the converter box.
PREVENTS: Watching scrambled channels while recording another channel.
*
*
Using the DVD/VCR tuner to select channels.
DVD/VCR
5
TV
Splitter
IN
(ANT)
VHF/UHF
IN (ANT)
Converter/
Descrambler
A/B Switch
Incoming
Cable
OUT
(TV)
A
B
ALLOWS: Recording of nonscrambled channels.
*
Recording of one channel while watching another.
Watching premium channels through the converter while recording nonscrambled channels.
Using the programmable timer.
*
*
*
PREVENTS: Recording scrambled channels.
DVD/VCR
Converter/
Descrambler
6
TV
Splitter
IN
(ANT)
VHF/UHF
IN (ANT)
Incoming
Cable
OUT
(TV)
Converter/
Descrambler
A/B Switch
A
B
ALLOWS: Recording of all channels through the converter box.
*
*
Recording a scrambled or unscrambled channel while watching another (scrambled or
unscrambled) channel.
Using the programmable timer to record only the channel selected at the converter box.
PREVENTS: Using the DVD/VCR tuner to select channels.
*
15
2C51001AE (12-15)
15
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback connections
The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is dependent
on the model and features of each component. Check the Owner's Manual provided with each component for the
location of video and audio inputs and outputs.
Connect to a TV with Audio/Video Output
You can enjoy playback by connecting the unit to a TV.
Connect the unit to a TV equipped with audio input (L/R) and video input jacks using the supplied audio/video cable.
TV
Video Output
DVD/VCR
To Video
Input
To Audio (R) Input
To Audio (L) Input
Audio (L) Output
Audio (R) Output
AUDIO/VIDEO cable (supplied)
Connect to a TV with S-Video Output (for DVD/CD playback)
If your TV has an S-VIDEO input, you can get higher quality by connecting it with the S-VIDEO output of the
unit using the S-video cable instead of connecting the video input of the TV to the VIDEO jack of the unit.
TV
S-Video cable (not supplied)
DVD/VCR
To S-Video
Input
To Audio (R) Input
S-Video Output
Audio (L) Output
To Audio (L) Input
S-VIDEO/COMPONENT
Video selector switch
Audio (R) Output
AUDIO cable (not supplied)
Connect to a TV with Component Video Output (for DVD/CD playback)
You can enjoy high quality picture by connecting the unit’s COMPONENT VIDEO OUT jacks to the
COMPONENT VIDEO IN jacks of your TV with the COMPONENT video cables (not supplied).
TV
DVD/VCR
To Component
Video Output
To Component Video Input
COMPONENT VIDEO cable (not supplied)
NOTES:
• When you connect to a TV with S-video jack or component jacks, set the S-VIDEO/COMPONENT Video
selector switch to the desired position.You must also select the corresponding video input on your TV.
• When connecting to a TV using the VIDEO or S-VIDEO jack, make sure that the PROGRESSIVE indicator
on the display window is not lit. If it is lit, the VIDEO and S-VIDEO outputs do not feed the correct
signals and you cannot see any picture.To turn off the PROGRESSIVE indicator, make the Progressive
scanning mode inactive (see page 52).
• When the component video input jacks on a TV is of the BNC type, use an adapter to convert a pin jack
to a BNC jack (not supplied).
16
2C51001AE (16-19)
16
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback connections
Connect to a Stereo Amplifier with Audio Output
You can enjoy high quality audio by connecting the audio output to your amplifier.
Connect the AUDIO OUT jacks to any line-level inputs (such as AUX, DVD, CD, etc.) of an audio amplifier.
DVD/VCR
Stereo Amplifier
To Audio (R) Input
To Audio (L) Input
Audio (L) Output
Audio (R) Output
AUDIO cable (not supplied)
Connect to an AV Amplifier with built-in digital surround
If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems such as Dolby
Digital and DTS by using the Optical or Coaxial Digital Output.
Use this connection to connect an:
• AV amplifier with built-in *Dolby Digital decoder
• AV amplifier with built-in *DTS decoder
Coaxial Digital Audio Output
Video cable (not supplied)
To Video
DVD/VCR
Input
Video Output
TV
NOTE:
AV Amplifier with
built-in various
decoder as above
You may connect to a TV with a
Component video cable (not supplied)
or S-Video cable (not supplied) instead
of a video cable (not supplied).
Coaxial digital cable (not supplied)
Connecting the optical digital cable
You may connect to an AV Amplifier with an Optical digital cable (not supplied) instead of a Coaxial digital cable.
When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel.
When not using the optical digital cable, attach the dust protection cap to protect against dust.
NOTES:
•
The DVD OUTPUT jacks (OPTICAL, COAXIAL, AUDIO L/R, S-VIDEO and COMPONENT) are useful only for
DVD section. The VHS signal is output only from the composite jacks (DVD/VCR OUTPUT) and UHF/VHF OUT.
When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on the AV
Amplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the
speakers to be damaged.
•
•
•
Caution for the optical digital audio output connector: Do not connect to an amplifier (with an optical digital input
connector) which does not contain a Dolby Digital or DTS decoder. Otherwise, any attempt to play DVDs may
cause such a high level of noise that it may be harmful to your ears and damage your speakers.
DTS audio will be output only from the COAXIAL or OPTICAL output. To hear DTS audio, DTS-Decoder is
necessary.
•
•
When playing DTS-encoded CDs, only noise will be heard from the speakers or analogue stereo outputs.
Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.
17
2C51001AE (16-19)
17
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the video channel / Setting the language
When a TV is connected with the 75 ohm coaxial cable only.
Setting the video channel
To view playback of a recorded tape
or DVD disc, or to watch a program
selected by the VCR's channel
selector, the TV must be set to
channel 3 or 4 (video channel).
Press and hold 3 or 4 on the remote
1 control for 3 seconds in the standby
mode to select CH 3 or 4. The selected
channel number will flash on the display for about 4 seconds.
Turn ON the TV and set to CH 3 or 4 to correspond with the
2 channel selected in step 1.
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
Press POWER to turn on the DVD/VCR.
3
DISPLAY/CALL
1
4
7
2
5
8
3
6
Press VCR/DVD to select the VCR mode. The VCR indicator
4 on the front panel will light.
INPUT SELECT/
PROGRESSIVE
Press TV/VCR to select the VCR position.
5 The VCR indicator will appear in the display.
9
0
Select any channel to receive a TV station in your area.
6 The channel number will appear on the screen for about
CH
4 seconds.
TRACKING/
SET
TRACKING/
SET
–
+
SELECT/
ENTER
For a push-button TV tuner
If CH 3 or 4 corresponding to the video channel cannot be tuned
on your TV, proceed as follows: set the VCR 3/4 channel selector
and the TV to CH 3 or 4, play back a prerecorded tape and tune
the TV to receive a sharp color picture from the video cassette
recorder. Refer to your TV owner's manual for details.
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
MARKER
ZOOM
TOP MENU REPEAT A-B
Setting the language
You can choose from three different languages (English,
French and Spanish) for the on-screen displays.
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
Press VCR MENU.
The VCR menu screen will appear. Press SET + or – to select
the “SYSTEM SETUP” menu, then
press ENTER.
If you use the unit for the first time
and press VCR MENU, instead of
the main menu screen on the right
the “SYSTEM SETUP” menu
SUB TITLE/
ATR
PLAY MODE/
SPEED
1
TIMER REC
TV/VCR
REW/SEARCH
PLAY
SEARCH/F.FWD
MENU
TIMER REC SET
ON OFF
ON OFF
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
SLOW
PAUSE/STILL
⟨+/-/ENTER/MENU⟩
screen in step 2 may appear.
NOTES:
Press SET + or – to select the
2 “LANGUAGE” option, then press
• When shipped from factory, the
video channel is set to CH 3.
ENTER.
• If the unit does not operate
properly, or No key operation (by
the unit and/or the remote control):
Static electricity, etc., may affect the
player's operation.Disconnect the AC
power cord, then connect it again.
• Both the VCR and the DVD have their
own menu option (See page 34).
• If no buttons are pressed for more
than 60 seconds, the MENU screen
will return to normal TV-operation
automatically.
Press SET + or – to select the
3 desired language: English (EN-
GLISH), Spanish (ESPAÑOL) or
French (FRANCAIS), then press
ENTER.
Press VCR MENU until the MENU screen is cleared.
4
18
2C51001AE (16-19)
18
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual clock setting
You must set the date and time for
timer recordings.
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the VCR mode. (The VCR indicator
will light.)
EXAMPLE: Setting the clock to “8:30 AM” March, 27 (SAT), 2004.
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
Press VCR MENU. The VCR menu screen will appear.
1
2
DISPLAY/CALL
1
4
7
2
5
8
3
6
Press SET + or – to select the
“SYSTEM SETUP” menu, then
press ENTER.
INPUT SELECT/
PROGRESSIVE
MENU
TIMER REC SET
ON OFF
ON OFF
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
9
0
⟨+/
-/ENTER/MENU⟩
CH
TRACKING/
TRACKING/
SET
SET
–
+
Press SET + or – to select the
SELECT/
ENTER
3 “CLOCK SET” option, then press
ENTER.
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
MARKER
ZOOM
TOP MENU REPEAT A-B
Press SET + or – to set the
4 month, then press ENTER.
AUDIO/
JUMP/
ANGLE/
CLOCK/
MONTH
DAY
3
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
1 (SAT)
2003
12 : 00AM
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
YEAR
TIME
⟨+/-/ENTER/CANCEL/MENU⟩
REW/SEARCH
PLAY
SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
To make corrections any time during the process
Press CANCEL repeatedly until the item you want to change
blinks, then press SET + or –.
SLOW
PAUSE/STILL
Set the day, year and time as in
step 4.
5
6
MONTH
DAY
3
27 (SAT)
2004
YEAR
TIME
8 : 30AM
⟨+/-/ENTER/CANCEL/MENU⟩
NOTE:
After a power failure or disconnection
of the power, the timer settings will be
lost. In this case, reset the present time.
After setting the clock, the date
and time will start functioning
automatically.
8 : 30AM SAT
19
2C51001AE (16-19)
19
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner setting
This DVD/VCR is equipped with a channel memory feature which allows channels to skip up or down to
the next channel set into memory, skipping over unwanted channels. Before selecting channels, they
must be programmed into the DVD/VCR’s memory. In addition to normalVHF and UHF channels, this DVD/
VCR can receive up to 113 Cable TV channels. To use this DVD/VCR with an antenna, set the TV/CATV
menu option to the TV mode. When shipped from the factory, this menu option is in the CATV mode.
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the VCR mode. (The VCR indicator
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
will light.)
DISPLAY/CALL
1
4
7
2
5
8
3
6
INPUT SELECT/
PROGRESSIVE
TV/CATV selection
Press VCR MENU. The VCR menu screen will appear. Press
1 SET + or – to select “CH SETUP”, then press ENTER.
9
0
CH
Press SET + or – to select the
2 “TV/CATV” option.
TRACKING/
SET
–
TRACKING/
SET
+
SELECT/
ENTER
CH
SETUP/
CLEAR/
DVD MENU
RETURN
Then press ENTER to select the
TV or CATV mode. The arrow
indicates the selected mode.
VCR MENU
CANCEL
CH SETUP
3
TV CATV
MARKER
ZOOM
TOP MENU REPEAT A-B
AUTO CH MEMORY
ADD/DELETE
AUDIO/
JUMP/
ANGLE/
CLOCK/
TV
- VHF/UHF channels
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
+/-/ENTER/MENU
CATV - CABLE TV channels
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
Press VCR MENU until the menu screen is cleared.
4
REW/SEARCH
PLAY
SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
Setting channels automatically
SLOW
PAUSE/STILL
The VCR can receive a maximum of 181 channels by
presetting the channels into memory.
Repeat above step 1 and press
CH SETUP
1 SET + or – to select “AUTO CH
TV CATV
MEMORY”.
AUTO CH MEMORY
ADD/DELETE
⟨+/-/ENTER/MENU⟩
NOTE:
You can’t select “CH SETUP” if you set
the channel to “L”.
Then press ENTER.
2
CH 002
The auto tuning will start. The
channel display will count up and
when finished, the screen returns
to normal.
20
2C51001AE (20-25)
20
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
To ADD/DELETE channels / Noise elimination
Preparation:
To ADD/DELETE channels
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the VCR mode. (The VCR indicator
will light.)
You can add the channels you want
or delete the channels you do not
want manually.
Repeat the step 1 on page 20.
Then press SET + or – to select
the “ADD/DELETE” option and
press ENTER.
OPEN/
CH SETUP
1
POWER
EJECT
CLOSE
VCR/DVD
TV CATV
AUTO CH MEMORY
ADD/DELETE
DISPLAY/CALL
1
4
7
2
5
8
3
6
INPUT SELECT/
PROGRESSIVE
⟨+/-/ENTER/MENU⟩
9
0
To Add or Delete desired channels
2
Press Number keys or SET +
or – to select a channel
number you want to add or
delete.
1
CH
ADD
CH 003
TRACKING/
TRACKING/
SET
SET
–
+
SELECT/
ENTER
2
To add channels
Press ENTER until “ADD”
appears on the screen to set
to add the unmemorized
channel.
⟨+/-/0-9/ENTER/MENU⟩
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
To delete channels
MARKER
ZOOM
TOP MENU REPEAT A-B
Press ENTER until “DELETE” appears on the screen to
set to delete the channel from memory. The channel
number will blink.
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
3
Repeat 1 to 2 to add or delete other channel.
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
Press VCR MENU until the menu screen is cleared.
3
REW/SEARCH
PLAY
SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
Noise elimination
SLOW
PAUSE/STILL
When you don't want to receive a weak signal broadcast, the
Blue back screen can be obtained by selecting the NO NOISE
BACKGROUND “ON”. When the unit is shipped from the
factory, the NO NOISE BACKGROUND is set to the “ON”.
Repeat the steps 1~2 on page 19 and press SET + or – to
select “ NO NOISE BACKGROUND”.
1
Press ENTER to select the “ON”
2 position.
Press VCR MENU until the menu screen is cleared.
3
21
2C51001AE (20-25)
21
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading and Unloading a cassette tape
Use only video cassette tapes marked
.
Loading
Insertthecassettetapewithitslabeledsidefacingup
and the erase prevention tab positioned at your left.
An inverted cassette tape cannot be inserted.
Push the center of the tape until it is automatically
inserted.
VCR
Erase prevention tab
Automatic power ON
When you insert a cassette tape the VCR power will turn ON automatically.
Automatic playback
When loading a cassette tape without an erase prevention tab, playback will start automatically.
Unloading
Press EJECT on the unit or the Remote.
Remove the cassette tape.
1
2
Automatic tape eject
This VCR will automatically rewind the tape when the tape has ended. And when the tape is rewinded to its
beginning, the cassette tape will be ejected automatically.
To prevent accidental erasure
To record again
Removetheerasepreventiontabwithascrewdriver.
Cover the hole with a piece of adhesive tape.
Screwdriver
Erase prevention tab
Adhesive tape
Tape speed and maximum recording time
Video cassette tape
Tape Speed
T-160
2-2/3 hours
8 hours
T-120
2 hours
6 hours
T-90
T-60
T-30
SP (Standard Play)
SLP (Super Long Play)
1-1/2 hours
4-1/2 hours
1 hour
3 hours
30 minutes
1-1/2 hours
22
2C51001AE (20-25)
22
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Cassette tape playback
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the VCR mode. (The VCR indicator
will light.)
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
Load a prerecorded tape
1
(When loading a cassette tape
DISPLAY/CALL
1
4
7
2
5
8
3
6
without the erase prevention
tab, playback will start auto-
matically).
INPUT SELECT/
PROGRESSIVE
To start playback
9
0
2
Press PLAY.
Playback will start.
CH
“
” will appear on the screen
TRACKING/
SET
–
TRACKING/
SET
+
for about 4 seconds.
SELECT/
ENTER
To stop playback
CH
Press STOP once.
The tape will stop but remain
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
fully loaded and ready to play.
MARKER
ZOOM
TOP MENU REPEAT A-B
“
” will appear on the screen
for about 4 seconds.
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
To rewind the tape or forward it rapidly
Stop the playback or recording with STOP.
REW/SEARCH
PLAY
SEARCH/F.FWD
To rewind the tape:
To forward the tape:
Press F.FWD.
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
Press REW.
SLOW
PAUSE/STILL
To stop the tape-winding, press STOP. To switch to playback
directly (without STOP), press PLAY.
NOTES:
Forward/Reverse picture search mode
• This VCR selects the playback tape
speed SP, LP or SLP automatically.
• The Cassette tape and DVD disc can
be played back simultaneously. If you
press VCR/DVD, the tape playback
and DVD playback alternate with each
other on the screen.
When the tape is being wound, you can switch to picture search
mode (see next page). To do this, press REW or F.FWDand hold
it down. The unit will resume the tape winding as soon as the
button is released.
• When you select the VCR mode during
DVD playback, DVD playback will stop
automatically after approx. 5 minutes.
23
2C51001AE (20-25)
23
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Special playback
Repeat playback
Picture Search
Reverse picture search function
The entire video tape will be played until its end. The
tape will then automatically rewind to the beginning and
the playback will be repeated.
Press REW x 1 or x 2 during the playback.
Forward picture search function
Press F.FWD x 1 or x 2 during the playback.
To return to playback: Press PLAY.
Press VCR MENU. Press SET + or – to select
AUTO REPEAT.
1
SPEED SEARCH TIMES
PICTURE SEARCH SPEED
TAPE SPEED
Then press ENTER to
select “ON” or “OFF”.
If “ON” is selected, the
playback will be
repeated endlessly.
2
MENU
PRESS ONCE
PRESS TWICE
TIMER REC SET
ON OFF
ON OFF
AUTO REPEAT
SAP
SP (Standard Play)
LP (Long Play)
3 X
7 X
9 X
5 X
9 X
CH SETUP
SYSTEM SETUP
SLP (Super Long Play)
15 X
⟨+/-/ENTER/MENU⟩
Still Picture
PressPAUSEduringplayback.Toresumenormal
playback: Press PLAY.
Press VCR MENU until the menu screen is
cleared.
if you press CALL, “ ” will appear on the screen.
3
4
Slow Motion
During playback press SLOW.
To return to playback: Press PLAY or SLOW.
To start the playback, press PLAY.
The playback will be repeated endlessly.
Slow tracking and vertical lock adjustment
If noise bars appear in the picture during slow motion,
press the TRACKING + or – to reduce the noise bars.
If the still picture jitters excessively, press TRACKING
+ or – to stabilize the still picture.
To cancel repeat mode:
Follow the above step 1, then press ENTER to select
the OFF position. Press VCR MENU to return to the
TV.
Frame by Frame picture
Press PAUSE during playback.
Press SLOW one by one: The picture advances frame
by frame.
To return to playback: Press PLAY or PAUSE.
Adjusting tracking condition
Automatic tracking adjustment
Whenever you insert a tape and start playback,
automatic tracking starts working and continuously
analyzes the signal to enable optimum picture quality
during playback.
Manual tracking adjustment
If automatic tracking cannot eliminate noises satisfactorily
during playback, press TRACKING +/– to eliminate the
noises. “MANUAL TR.” will appear. Press it briefly for a
fine adjustment, or press and hold for a coarse
adjustment.
•
Press ATR to reactivate automatic tracking again.
“AUTO TR.” will appear.
NOTES:
The audio output is muted during SPEED SEARCH,
STILL, FRAME ADVANCE and SLOW MOTION.
•
• During picture search mode there will be noise bars
which are caused by the system.
• The Special Playback will automatically change to
playback after approx. 5 minutes to protect the video
tape against excessive wear.
24
2C51001AE (20-25)
24
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
ZERO RETURN function / Video index search system
Preparation:
• Turn ON the TV and set it to the video input mode.
• Press VCR/DVD to select the VCR mode. (The VCR indicator
will light.)
ZERO RETURN function
This function makes tape-rewinding
stop at the counter 00:00:00 position
automatically.
DISPLAY/CALL
1
4
7
2
5
8
3
6
Press CALL.
The counter display shows the tape
running time during playback or
recording.
1
2
3
8 : 47AM MON
HI-FI
INPUT SELECT/
PROGRESSIVE
VCR
00 : 04 : 38 SP
9
0
CH
Press COUNTER RESET at the desired
tape position.The counter display will be
reset to the “00:00:00” position (e.g. the
8 : 47AM MON
HI-FI
TRACKING/
TRACKING/
SET
SET
–
+
SELECT/
ENTER
beginning of recording).
VCR
00 : 00 : 00 SP
CH
Press STOP when playback or recording is finished.
Press ZERO RETURN.
The tape will be rewinded or fast forwarded and automatically
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
MARKER
ZOOM
TOP MENU REPEAT A-B
stop at the “00:00:00” position.
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
The CLOCK/COUNTER-button
Press CLOCK/COUNTER. The clock and tape
SUB TITLE/
ATR
PLAY MODE/
SPEED
VCR
TIMER REC
TV/VCR
counter alternate with each other in the display.
REW/SEARCH
PLAY
SEARCH/F.FWD
VCR
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
SLOW
PAUSE/STILL
NOTES for Counter Display:
Video index search system
This function enables you to locate the beginning of any
recording made on the VCR.
•
If you rewind the tape beyond
“00:00:00”, a minus sign (“–”) will be
displayed in front of the time.
•
•
When you load a tape, the counter will
reset to “00:00:00”.
The counter does not function on
nonrecorded (blank) sections of the
tape.Whenyourewind,fastforwardor
play tapes through blank sections, the
counter stops.
Recording an INDEX MARK
The Index Search function automatically
records an INDEX mark on the tape
whenever a recording is initiated.
CH 001
INDEX
NOTES for Video index search system:
Index Search
Press INDEX
mode.
For Succeeding programs: Press INDEX
For Preceding programs: Press INDEX
(Additional press increases the INDEX NO.
up to 9.)
When the INDEX
unit starts searching the INDEX NO.
selected and finds the portion, then playback
starts automatically.
To stop the Index Search, press STOP.
•
When you record an INDEX mark at
the very beginning of the tape, the
mark may not be found.
During INDEX search, the tape may
stop and begin to play at a slightly
different location.
or
during stop or play
+3
•
.
.
•
•
INDEX may not function properly with
old or worn out video tapes.
INDEX marks may not be found if it is
extremely close to the point where the
search began.
In recording, if you stop recording
temporarily, the INDEX mark is not
recorded on the tape.
or
is pressed, the
or
is displayed
INDEX NO. (up to 9)
•
25
2C51001AE (20-25)
25
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a TV program
Recording and viewing the
same TV program
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the VCR mode. (The VCR indicator
will light.)
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
Load a cassette tape with the erase
prevention tab intact.
The VCR will automatically turn on.
DISPLAY/CALL
1
1
4
7
2
5
8
3
6
INPUT SELECT/
PROGRESSIVE
9
0
Press SPEED to select the desired tape
2 speed SP or SLP.
CH
The tape counter and SP or SLP will
appear on the screen for about 4
TRACKING/
SET
–
TRACKING/
SET
+
00 : 00 : 00 SP
seconds.
SELECT/
ENTER
Set the TV/CATV option to the appropriate position (See page
3
CH
20).
SETUP/
CLEAR/
TV
- VHF/UHF channels
DVD MENU
RETURN
VCR MENU
CANCEL
CATV - CABLE TV channels
MARKER
ZOOM
TOP MENU REPEAT A-B
Press Number keys or CH
/
to select the channel to be
4 recorded.
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
1-9
Press 0 twice and then 1-9 as required. Example: To
select 2, Press “002”.
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
10-12
13-99
Press 0 first and then the remaining 2 digits in order
from left to right.
REW/SEARCH
PLAY
SEARCH/F.FWD
Example: Press 012 for “12”.
Press 2 digits in order.
CH 110
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
Example: Press 22 for “22”.
100-125 Press the 3 digits in order.
SLOW
PAUSE/STILL
Example: Press 110 for “110”.
VHF/UHF/CATV CHANNELS
TV
CATV
VHF
2-13
VHF
2-13
UHF
14-69
STD/HRC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100)(125)
01 (5A)
NOTES:
• Iftheerasepreventiontabisremoved,
the tape will eject when REC/OTR is
pressed for recording.
• If you wish to watch the DVD playback
during the normal recording on VCR,
press VCR/DVD to change to DVD
mode and perform the DVD playback
(see page 35).
• You can not record disc material in
DVD, Audio CD, etc. onto a video tape
with this DVD/VCR.
Press REC/OTR.
5 “
CH 110
” will appear on the screen for
about 4 seconds and “REC” will
appear on the display.
INDEX
26
2C51001AE (26-31)
26
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a TV program
To stop recording
Press STOP to stop recording.
” will appear on screen for about 4
“
seconds.
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
To stop recording temporarily
Press PAUSE/STILL to avoid recording
unwanted material.
DISPLAY/CALL
1
4
7
2
5
8
3
6
“
” will appear on screen for about 4
INPUT SELECT/
PROGRESSIVE
seconds.
Press again to continue the recording.
9
0
NOTES:
•
The pause function will be released after 5 minutes to prevent damage
to the tape or the VCR. The VCR will change to the STOP mode.
You can select a recording channel in the recording pause mode.
CH
•
TRACKING/
TRACKING/
SET
SET
–
+
SELECT/
ENTER
Recording one program while watching another
While the VCR is recording, press TV/VCR to select the TV position.
The “VCR” will go off and recording will continue.
Select the TV channel you want to watch by using the TV channel
selector.
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
MARKER
ZOOM
TOP MENU REPEAT A-B
NOTE:
Some CATV hookups do not permit viewing one channel while
recording another. See pages 14,15.
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
To Display VCR operation Status
REW/SEARCH
PLAY
SEARCH/F.FWD
Press CALL. The clock, day of the week and more information will be
indicated.
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
While watching TV
DAY OF THE WEEK
SLOW
PAUSE/STILL
CLOCK
8 : 47AM MON
STEREO SAP
CH 125
CHANNEL
STEREO AND
SECOND AUDIO
PROGRAM (SAP)
00 : 00 : 00 SP
TAPE SPEED
REAL TIME COUNTER
While operating a tape
Auto Rewind feature
This VCR will automatically rewind the
tape when the tape has ended (except
during OTR and TIMER REC). It will
also eject the tape.
OPERATING
MODE
HI-FI STEREO
AUTO REPEAT
TAPE IN
To cancel the display: Press CALL until all indicators disappear.
27
2C51001AE (26-31)
27
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
One-touch Timer Recording (OTR)
The One-touch Timer Recording
feature provides a simple and
convenient way to make a timed
recording.
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the VCR mode. (The VCR indicator
will light.)
OPEN/
Example: One-touch Timer Recording for 30 minutes.
POWER
EJECT
CLOSE
VCR/DVD
DISPLAY/CALL
1
4
7
2
5
8
3
6
Load a cassette tape with the erase
prevention tab intact.
The VCR will automatically turn on.
1
INPUT SELECT/
PROGRESSIVE
9
0
CH
Press SPEED to select the desired tape
2 speed SP or SLP.
TRACKING/
SET
–
TRACKING/
SET
+
The tape counter and SP or SLP will
appear on the screen for about 4
seconds.
SELECT/
ENTER
00 : 00 : 00 SP
Set the TV/CATV option to the appropriate position (See page
CH
3
20).
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
TV
- VHF/UHF channels
CATV - CABLE TV channels
MARKER
ZOOM
TOP MENU REPEAT A-B
Press Number keys or CH
/
to
4 select the channel to be recorded.
AUDIO/
JUMP/
ANGLE/
CLOCK/
CH 110
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
REW/SEARCH
PLAY
SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
Press REC/OTR. Press the button again to stop recording after
30 minutes. Each additional press of REC/OTR will increase
recording time as shown in the chart below, up to a maximum of
6 hours. The OTR and recording time will appear on the screen
for about 4 seconds. And, REC will keep blinking in the display.
5
SLOW
PAUSE/STILL
Press
once
Press
Recording time
NORMAL REC
0:30
Recording time
3:00
6 times
7 times
8 times
9 times
10 times
4:00
twice
5:00
3 times
4 times
5 times
1:00
6:00
1:30
NORMAL REC
2:00
NOTE:
If you wish to watch the DVD playback
during the OTR, press VCR/DVD to
change to DVD mode and perform the
DVD playback (see page 35).
To cancel OTR
Press STOP or turn off the power.
” will appear on screen for about 4
seconds.
“
28
2C51001AE (26-31)
28
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer recording
Timer recording can be programmed
on-screen with the remote control.
The built-in timer allows automatic
unattended recording of up to 8
programs within 1 month.
Preparation:
Press VCR/DVD to select the VCR mode.
Load a cassette tape with the erase prevention tab intact.
Press the CALL button to verify that the time and date are
correct (see page 27).
•
•
Example: Program a timer recording for the 26th day, channel 125
(CATV), 11:00 - 11:30 PM on timer program number 1 (Tape speed: SLP).
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
DISPLAY/CALL
1
2
3
Press VCR MENU. Select the
1
“TIMER REC SET” option , then
press ENTER.
INPUT SELECT/
PROGRESSIVE
4
5
6
TRACKING/
TRACKING/
SET
SET
–
+
SELECT/
ENTER
Press SET + or – to select one of the
2 program line, then press ENTER.
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
MARKER
ZOOM
TOP MENU REPEAT A-B
Press SET + or – to select the date,
then press ENTER.
3
AUDIO/
JUMP /
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
Set the start time, end time, channel
4 and tape speed as in step 3.
NOTES:
NOTES:
• Iftheclocksymbol( )blinkswhenthe
timerrecordingended,theTVprogram
has not been completely recorded
becauseofaninsufficienttapesupply.
Press TIMER REC to cancel the timer
program or press EJECT to remove
the cassette tape.
• PressCANCELtomovecursorbackward
for correction.
• To record from external source set the
channel to “L”. “L” will appear next to CH
125 (or 69).
To enter other programs, repeat step
2 through 4.
5
• During timer recording standby mode,
the VCR mode cannot be selected. To
use the VCR, press TIMER REC at
first, then press VCR/DVD to change
to VCR mode. After you use the VCR,
pressTIMERRECagaintoputtheVCR
into timer recording standby mode.
• If you press TIMER REC during timer
recording, the recording operation will
be interrupted. If you press TIMER
RECagainwithintheprogrammedtime,
the recording operation will start again.
• After a power failure or disconnection
of the power plug, all programmed
recording settings and time display
will be lost upon resumption of power.
In this case, reset the clock (see page
19) and reprogram any timer
recordings.
• To return to the normal screen,
press VCR MENU twice.
Press TIMER REC. The clock symbol( ) will appear on the
6 display and the VCR stands by for recording. At the same
time, VCR mode will change to DVD mode automatically. You
can use DVD even if the VCR is in the Timer recording mode.
If you do not use the DVD, turn the power off.
The timer recording will start at 20 seconds before the time
you predetermined.
NOTES:
• If the clock symbol( ) does not appear on the display in spite
of the pressing of TIMER REC, the cassette may not have been
loaded yet. (see page 22)
• If the cassette is ejected in spite of the pressing of TIMER REC,
the erase prevention tab of the cassette may have be2en9
removed. (see page 22)
2C51001AE (26-31)
29
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer recording
Timer recording special case
Weekly (e.g. WKL-TU: each Tuesday) or daily (e.g.
MO-SA: Monday to Saturday) Timer recording
Confirmation / Cancellation of the Timer
recording
If the Timer has been activated, press TIMER REC
Follow the procedure of timer recording on the previous
page. At picture 3 press SET + or – repeatedly until the
desired setting appears. Then press ENTER.
1
to deactivate the Timer. The clock symbol( ) will
disappear. Then press VCR/DVD to change to
VCR mode.
When you press SET – repeatedly, the indicator at
DATE will change as follows, in this case the day is
Friday.
To confirm Timer program:
2
At picture 1 on the
previous page select the
“TIMERRECSET”option
and press ENTER.
Then the timer program
list as right will appear on
the screen.
The current day (Friday)
SU-SA (Sunday to Saturday)
MO-SA (Monday to Saturday)
MO-FR (Monday to Friday)
WKL-TH (Weekly Thursday)
One month later
minus one day
WKL-WE
(Weekly Wednesday)
To cancel Timer program:
3
Press SET + or – to
select the unnecessary
program, then press
CANCEL to cancel the
program.
Press VCR MENU repeatedly until the TV-picture
appears.
4
In case Timer programs-overlap
•
Do not overlap timer programs as portions of the
conflicting programs will be lost. The first recording
timehaspriorityoverthenextrecordingtimeasshown
in the diagram below.
NOTES:
• If there are other timer record programs remaining,
TIMER REC must be pressed to reactivate the timer,
otherwisetheremainingtimerrecordprogramswillbe
ignored.
• You cannot confirm the Timer program during timer
recording operation.
8 : 00
9 : 00
10 : 00
11 : 00
Program 1
Program 2
Deleted Parts
Program 3
Non Recorded Portion Parts
Recording
Control Settings
•
Youcanalsocorrecttheprogrammedsettinginprogram
confirm mode.
Prog.1
Prog.2
Prog.3
At step 2 above, press ENTER to enter the program
input mode. Then press ENTER repeatedly until the
item you wish to correct
blinks.Thencorrectthedata
with SET + or –.
Then press VCR MENU re-
peatedlyuntiltheTV-picture
appears.
DATE
START END
CH
26(SU) 1–1::0–0–PM 1–1::3–0–PM125 SLP
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – –
– – –
– – –
– – –
– – –
– – –
– – –
–
–
–
–
–
–
–
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
NOTES:
•
The daily/weekly recording can be made continu-
ously until the recording is canceled or the tape
reaches the end.
+/–/ENTER/CANCEL/MENU
•
During timer recording the automatic rewinding
mechanism does not function.
30
2C51001AE (26-31)
30
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo recording and playback / Second Audio Program (SAP)
Stereo recording and
When a MTS STEREO broadcast is
received, the word STEREO will ap-
pearonthescreenandtheprogramcan
be viewed or recorded in stereo.
The Hi-Fi STEREO recording procedure
is the same as for normal recordings.
playback
STEREO
The VHS Hi-Fi audio system permits high
fidelity recording of MTS STEREO TV
broadcasts.
OPEN/
NOTE:
POWER
EJECT
CLOSE
VCR/DVD
WhenusingaCATVsystem, stereoTVprogramsmaybetransmitted
over a mono cable channel. In this case the word “STEREO” will not
appear and the sound will be in mono.
DISPLAY/CALL
1
4
7
2
5
8
3
6
INPUT SELECT/
PROGRESSIVE
Output selection
When viewing an MTS STEREO TV program, or playing a prerecorded
VHS Hi-Fi STEREO videotape, press AUDIO SELECT to select how
the audio will be heard through the speakers. Normally set to the Hi-Fi
STEREO position, this button can be set to the MONO position if the
stereo broadcast or videotape audio is of poor quality. The “R” and “L”
positions allow the audio from the Right or Left Hi-Fi channel to be heard
over both TV speakers.This button has no effect when viewing a MONO
videotape orTV program.Each time when you press the button, OUTPUT
SELECTION display appears on the screen for several seconds. Refer
to the chart below.
9
0
CH
TRACKING/
SET
–
TRACKING/
SET
+
SELECT/
ENTER
OUTPUT
SELECTION SPEAKERS
SOUND HEARD ON BOTH
CH
SETUP/
CLEAR/
STEREO
L ch
R ch
STEREO
DVD MENU
RETURN
VCR MENU
CANCEL
LEFT CHANNEL AUDIO
RIGHT CHANNEL AUDIO
MONO
MARKER
ZOOM
TOP MENU REPEAT A-B
MONO
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
Second Audio Program (SAP)
Your VCR is fitted with a SAP broadcast system which enables
you to switch to a second audio program when viewing a
selected channel.
This function applies only when the program is broadcast in
multi-languages through the SAP broadcast system.
REW/SEARCH
PLAY
SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
SLOW
PAUSE/STILL
Press VCR MENU. Then press SET + or – to select “SAP”.
1
2
Then press ENTER to select “ON”.
Then press VCR MENU until the
menu screen is cleared.
NOTES:
Listening to SAP
• When playing back a tape that is not
recorded in Hi-Fi stereo mode, the
audio will automatically be monaural.
• When listening to a VHS Hi-Fi video
tape or MTS broadcast through the
VHF/UHF jack (Audio/Video cord not
connected), the sound will be
monaural.
When the VCR is turned on or a channel selection is made, make
certain the letters “SAP” appear on the screen. This means that the
“Second Audio Program” broadcasting is available.
STEREO SAP
SAP
OR
31
2C51001AE (26-31)
31
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Duplicating a video tape
Duplicating a video tape
If you connect the VCR to another VCR or camcorder, you can duplicate a previously recorded tape.
Make all connections before turning on the power.
Load a blank cassette tape with the erase preven-
tion tab intact into the recording VCR.
Load a previously recorded tape into the playback
VCR or CAMCORDER.
Press REC/OTR on the recording VCR, then press
PAUSE/STILL.
1
2
3
4
5
6
Press SPEED to select the desired tape speed SP
or SLP.
It is recommended that you set the Speed to the
SP mode on the recording VCR for best results.
Press the PLAY button on the playback VCR or
CAMCORDER, then press the PAUSE/STILL but-
ton.
Release the recording pause and the playback still
simultaneously to begin the duplicating process.
Press INPUT SELECT to select AUDIO/VIDEO in-
put position. “L” will appear in the
display.
Connection with Video camera
Connection with second Video recorder
Playback VCR
Playback Camcorder
To AV Jack
To VIDEO OUT
To AUDIO (R) OUT
To AUDIO (L) OUT
Recording VCR
AUDIO/VIDEO Cord (supplied)
Recording VCR
To AUDIO (R) IN
To AUDIO (L) IN
AUDIO/VIDEO Cord (not supplied)
To VIDEO IN
To AUDIO (R) IN
To AUDIO (L) IN
To VIDEO IN
For duplicating a previously recorded tape from a
camcorder, follow the camcorder manufacturer’s
instructions. A typical camcorder dubbing hookup
is shown above.
32
2C51001AE (32-33)
32
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc
This unit applies to DVD discs from Region 1 only.
The loaded Disc (DVD, Audio-CD and MP3-CD) will be recognized automatically.
The suitable Disc-formats are: DVD, CD-R and CD-RW.
Some CD-R/RW discs may be incompatible.
Do not play DVD-ROM, DVD-Audio, CDV, Video-CD, CD-G or Photo CD to prevent accidental erasure of prere-
corded material.
This unit cannot record disc material in DVD, Audio CD etc. onto a video tape.
If you press the REC/OTR during DVD playback, a symbol mark "
seconds.
" will appear on the screen for aprox.4
Title
When two or more movies are recorded on a disc,
the disc is divided into two or more sections. Each
section is called a “TITLE”.
Chapter
The titles can be subdivided into many sections.
Each section is called a “CHAPTER”.
Audio-CD
Track
TRACK
1
TRACK
2
TRACK
3
TRACK
4
TRACK
5
An Audio CD can contain several items.
These are assigned to the tracks.
Removing Disc from Case
Be sure to hold the edge of disc. Do not touch the surface of the disc.
Pick up the disc gently from the case.
• Do not scratch the disc.
• Do not get dirt on the surface of the disc.
• Do not stick a label or adhesive tape on the disc.
• Do not drop or bend the disc.
Storing Disc
• Store the disc in the case to avoid risk of scratches, dirt or damage.
• Do not leave disc exposed to direct sunlight or in hot or humid places.
Cleaning Disc
Wipe the disc with a clean, dry cloth from center to edge.
• Do not wipe the disc round.
• Do not use liquid or aerosol cleaners.
33
2C51001AE (32-33)
33
18/11/03, 2:38 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting setup language
The setup language can be selected.
Preparation:
• Turn ON the TV and set to the video input mode.
• When using an amplifier, switch on the amplifier.
Press VCR/DVD to select the
DVD mode. (The DVD indicator
will light)
“No Disc” will appear on the
screen.(IfaDVDdischasalready
loaded, the playback will start
automatically.)
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
1
No Disc
DISPLAY/CALL
1
2
3
6
INPUT SELECT/
PROGRESSIVE
4
7
5
8
9
0
Press SETUP in the stop mode.
The SETUP MENU of DVD will
appear on the screen.
Language Picture Sound Parental Other
2
3
4
CH
TRACKING/
SET
–
TRACKING/
SET
+
Then press
to select Other.
SELECT/
ENTER
/Enter/Setup/Return
CH
Press
or ENTERtoselectOSD
Language Picture Sound Parental Other
OSD Language English
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
Language.
MARKER
ZOOM
TOP MENU REPEAT A-B
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
/Enter/Setup/Return
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
Language Picture Sound Parental Other
Press
press
or ENTER and then
REW/SEARCH
PLAY
SEARCH/F.FWD
or
to select desired
OSD Language English
English
Francais
Espanol
language (e.g. English), then
press ENTER.
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
SLOW
PAUSE/STILL
/Enter/Setup/Return
NOTE: To make the SETUP screen disappear, press SETUP
(or RETURN).
If the DVD/VCR does not operate
properly: Static electricity, etc., may
affect the player's operation.Disconnect
the AC power cord once, then connect
it again.
34
2C51001AE (34-37)
34
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback procedure
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
DISPLAY/CALL
1
2
3
6
Press OPEN/CLOSE.
1
The disc tray will open.
INPUT SELECT/
PROGRESSIVE
4
7
5
8
0
Place a disc onto the tray.
9
2 Hold the disc, position it with the
printed label side up, align it with
the guides, and place it in its
proper position.
CH
TRACKING/
SET
–
TRACKING/
SET
+
SELECT/
ENTER
Press PLAY or OPEN/CLOSE.
3
The disc tray closes automati-
cally.
On the screen,
changes to
CH
“Reading” and then playback will
commence.
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
MARKER
ZOOM
TOP MENU REPEAT A-B
• A menu screen may appear on
the TV screen, if the disc has
a menu feature. In this case,
Reading
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
press
,
,
,
or
SUB TITLE/
ATR
PLAY MODE/
SPEED
ENTER to operate a menu
TIMER REC
TV/VCR
feature.
REW/SEARCH
PLAY
SEARCH/F.FWD
Press STOP to end playback.
• The DVD/VCR memorizes the stopped point, depending on
the disc. “ ” appears on the screen for approx. 4 seconds.
4
5
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
“
” keep blinking in the display until the playback is stopped
SLOW
PAUSE/STILL
completely. Press PLAY to resume playback (from the scene
point).
• If you press STOP again(“ ”appears on the screen) or unload
the disc, the DVD/VCR will clear the stopped point.
Then press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press POWER.
The disc tray closes automatically and DVD/VCR turns off.
NOTES:
•
If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV
screen according to the type of loaded disc. In this case, check your disc again (See pages 33 and 44).
Some discs may take a minute or so to start playback.
A “Prohibition” symbol may appear at the upper left of the screen. This symbol means either the feature you
tried is not available on the disc, or the DVD/VCR can not access the feature at this time. This does not indicate
a problem with the DVD/VCR.
•
•
•
•
When you set a single-faced disc label downwards (ie. the wrong way up) and press PLAY or OPEN/CLOSE,
“Reading” will appear and remain on the screen for approx. 40 seconds and then it will change to “Incorrect Disc”.
Some playback operations of DVDs may be intentionally fixed by software producers. Since this DVD/VCR plays
DVDs according to the disc contents the software producers designed, some playback features may not be
available. Also refer to the instructions supplied with the DVDs.
•
When playing DTS-encoded Audio CDs, excessive noise will be heard from the analog stereo outputs. To avoid
possible damage to the audio system, the consumer should take proper precautions when the analog stereo
outputs of the DVD/VCR are connected to an amplification system.
35
2C51001AE (34-37)
35
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Special playback
Note: There may be a slight delay
between pressing the button and the
function activation.
Fast Forward Playback
Press F.FWD during normal playback.
Each press of F.FWD will increase the speed of the search
(x2),
(x2),
(x4),
(x8),
(x20).
• To resume normal playback, press PLAY.
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
Review Playback
DISPLAY/CALL
1
2
3
6
Press REW during normal playback.
Each press of REW will increase the speed of the search
INPUT SELECT/
PROGRESSIVE
(x4),
(x8),
(x20).
4
7
5
8
• To resume normal playback, press PLAY.
9
0
CH
Still Playback
TRACKING/
SET
–
TRACKING/
SET
+
Press PAUSE/STILL during normal
playback.
SELECT/
ENTER
To resume normal playback, press
PLAY.
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
MARKER
ZOOM
TOP MENU REPEAT A-B
Frame Advance
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
PressPAUSE/STILLduringstillplay-
back.
One frame is advanced each time
you press PAUSE/STILL.
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
REW/SEARCH
PLAY
SEARCH/F.FWD
To resume normal playback, press
PLAY.
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
SLOW
PAUSE/STILL
Slow-motion Playback
Press SLOW during normal playback or still playback.
Each press of SLOW will change the speed of the slow x1/2, x1/4,
x1/6, x1/7.
• To resume normal playback, press PLAY.
• To resume the still playback, press PAUSE/STILL.
NOTE:
The unit is capable of holding a still video
image or On screen display image on your
television screen indefinitely. If you leave
the still video image or On screen display
image displayed on your TV for an ex-
tended period of time, you risk permanent
damage to your television screen. Pro-
jection and CRT televisions in particular
are very susceptible.
Locating a chapter or track
Press SKIP (
) Forward or SKIP (
) Reverse during play-
back to locate a chapter that you want to watch.
Each time you press the button, a chapter or track is skipped.
36
2C51001AE (34-37)
36
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Zooming/Locating desired scene
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
Zooming
This unit will allow you to zoom in on the frame image. You can
then make selections by switching the position of the frame.
Press ZOOM during playback.
The center part of the image will
be zoomed in.
1
1
EachpressofZOOMwillchange
the ZOOM
1 (x 1.3),
2 (x
1.5) and
3 (x 2.0).
Press
/
or
/
to view a different part of the frame.
2
3
You may move the frame from the center position to UP, DOWN,
LEFT or RIGHT direction.
In the zoom mode press ZOOM repeatedly to return to a 1:1
view (
Off).
Locating desired scene
Use the title, chapter and time recorded on the disc to
locate the desired point to play back.
Tocheckthetitle, chapterandtime, pressDISPLAY. (seepage50)
Press JUMP during playback or
stop mode.
1
Jump
Time
Title
Chapter
/Enter/0 9/Cancel/Jump
Press
or
to select the “Time”, “Title” or “Chapter”.
2
3
Press Number keys to change the number.
• If you input a wrong number, press CANCEL.
• Refer to the package supplied with the disc to check the
numbers.
NOTE:
You can use the Pause, Slow, Search
or Skip feature in the zoom mode.
Press ENTER.
Playback starts.
4
• When you change the title, playback starts from Chapter 1 of
the selected title.
• Some discs may not work in the above operation.
37
2C51001AE (34-37)
37
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat playback
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
Title, Chapter, Track Playback
Press PLAY MODE during playback or stop mode.
1
DVD
CD
Repeat
:
Off
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
/Enter/Play Mode
Press ENTER once or twice to select “Chapter” or “Title”.
2
3
In case of CD, at first press
to select “Repeat” and then press
ENTER once or twice to select “Track” or “All”.
DVD
CD
Repeat
:
Chapter
Play Mode
Repeat
:
:
Off
All
/Enter/Play Mode
/Enter/Play Mode
Press PLAY MODE again to make the screen disappear.
• Press PLAY to start Repeat playback.
• To resume normal playback, select Repeat Off.
A-B Repeat Playback
A-B repeat playback allows you to repeat material between two
selected points.
Press REPEAT A-B during
playback.
The start point is selected.
1
A
NOTES:
•
•
•
•
Some discs may not work with the
repeat operation.
In A-B repeat mode, subtitles near
point A or B may not appear.
During the A-B Repeat Playback the
ANGLE feature will not operate.
You may not be able to set A-B Re-
peat, depending on the scenes of the
DVD.
Press REPEAT A-B again.
2
A B
The end point is selected.
Playback starts at the point that
you selected. Playback stops at
the end point, returns to Point A
automatically, then starts again.
•
A-B repeat does not work with an in-
teractive DVD and MP3-CD.
To resume normal playback press REPEAT A-B again.
” appears on the screen.
“
Off
38
2C51001AE (38-43)
38
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Program playback/Random playback (CD)
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
Program playback
You can arrange the order of tracks on the disc.
Press PLAY MODE in the stop
mode.
1
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
Press ENTER repeatedly until
the program table shown at right
appears.
Play Mode
Repeat
:
:
Program
Off
2
3
1
2
3
4
5
6
7
8
9
10
11
12
Clear
Program Playback
/Enter/0 9/Cancel/Play Mode
Example: In case you wish to
program in order of 7, 3, 11:
Enter as 7 , 3 , 11.
Play Mode
Repeat
:
:
Program
Off
1 7
4
7
8
9
10
11
12
2 3
3 11
Clear
5
6
If you input a wrong number,
press CANCEL.
Program Playback
/Enter/0 9/Cancel/Play Mode
Press
/
or
/
to select
4 “Program Playback” and press
Program Playback
ENTER. “Program Playback” will
appear on the screen. The
program you selected will begin
to playback in the order set.
Toreturntonormalplayback,select
“Play Mode: Off” at step 2 above.
Random playback
Press PLAY MODE in the stop
mode.
1
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
NOTES:
•
•
•
Tocancelprogramplay, select“Clear”
at step 4 and press ENTER.
The program is cancelled when you
openthedisctrayorturnthepoweroff.
Random playback can not be
combined with Repeat playback.
Press
/
toselect“Random”.
2
3
Play Mode
Repeat
:
:
Random
Off
/Enter/Play Mode
Press PLAY.
“Random Play” will appear on the screen and Random Playback
will start.
39
2C51001AE (38-43)
39
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
MP3 playback
This player can play back the MP3-data
which has been recorded on CD-R or CD-
RW. To produce the MP3-data, you need a
Windows-PCwithCD-ROMdriveandaMP3-
encoding Software (not supplied).
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD
indicator will light.)
The Apple-HFS-System can not be played.
Press OPEN/CLOSE.
The disc tray will open.
Place a disc onto the tray.
1
MP3 CD Information
Limitations on MP3 CD playback
• MP3 CD is the disc that is standardized by
ISO9660, its file name must include 3-digits
extension letters, “mp3”.
• The directory and file names of the MP3
CD must correspond to the ISO
Press PLAY or OPEN/CLOSE.
Reading
2
The disc tray closes automatically.
On the TV-screen, “Reading” will
appear.Reading will take as much
time as the number of file.
standardized files.
• This unit can read 200 files per disc. If
one directory has more than 200 files, it
reads up to 200 files, the remaining files will
be omitted.
• As for multi-session disc, only the first
session can be played.
• If the CD has both audio tracks and MP3
files, only audio tracks are played.
• It may take more than one minute for this
unit to read MP3 files depending on its
structure.
-
/72 --:--
CD-R
A MP3 menu screen will appear
on the TV screen.
3
Pops
1
2
3
4
5
6
7
8
Japan
flower
Bay Bridge
CLOSE MY EYES
DIVE TO BLUE
Honey
BLUE EYES
Blurry Eyes
9
Lies and Truth-
winter fall
Rain
Strawberry
Welcome party
Thailand
Press
folder.
/
or ENTER to select
10
11
12
13
14
/0-9/Enter/Play Mode
• Music recorded by “Joliet Recording
Specification” can be played back, the file
name is displayed (within 16 letters) on the
screen. Long file names will be condensed.
• The music files recorded by “Hierarchical
File System” (HFS) cannot be played.
Press
/
or
/
or Number keys to select the desired
4
track, then press ENTER. Track is selected and play
commences.
• In case the folder includes more than 15 tracks, press
or
to display next track list.
-
/72 --:--
CD-R
-/72 --:--
CD-R
Pops
Pops
1
2
3
4
5
6
7
8
Japan
flower
Limitations on display
15
16
Mother
Hold Your Last
Bay Bridge
CLOSE MY EYES
DIVE TO BLUE
Honey
BLUE EYES
Blurry Eyes
9
Lies and Truth-
winter fall
Rain
Strawberry
Welcome party
Thailand
• The maximum number for display is 16
letters. Available letters for display are the
following: capital or small alphabets of A
through Z, numbers of 0 through 9, and _
(under score).
10
11
12
13
14
/0-9/Enter/Play Mode
/0-9/Enter/Play Mode
• Other characters than those above are
replaced by a hyphen.
Press STOP to end playback.
5
6
• The unit records the stopped point. “ ” appears on the
screen. Press PLAY to resume playback (from the scene
point).
• If you press STOP again or unload the disc, the unit will
clear the stopped point.
Notes on MP3 files
To play back MP3 CD in the recorded order,
1. Use MP3 software that records data
alphabetically or numerically.
2. Name each file including two-digit or three-
digit number (e.g. “01” “02” or “001” “002”).
3. Refrain from making too many sub-folders.
Then press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press POWER.
The disc tray closes automatically and DVD/VCR turns off.
CAUTION:
• Some MP3 CDs can not be played back
depending on the recording conditions.
• The CD-R/RW that has no music data or
non-MP3 files can not be played back.
NOTES:
•
During MP3-Playback, you can not use SEARCH, A-B
Repeat functions.
•
You can use Repeat (Track or All), Random functions and
Program playback for MP3 CD Playback. (See pages 38 and 39)
40
2C51001AE (38-43)
40
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Marking desired scenes
The unit stores the points that you
want to watch again up to 3 points.
You can resume playback from
each scene.
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
Marking the Scenes
Press MARKER during
playback.
1
Marker
Marker
Marker
1
2
3
/Enter/Cancel/Marker
Select the blank Marker using
2
3
Marker
Marker
Marker
1
2
3
00 27 54
/
.
ThenpressENTERatthedesired
scene.
/Enter/Cancel/Marker
• Repeat this procedure to set
the other 2 scenes.
Press MARKER to remove this display.
Returning to the Scenes
PressMARKERduringplayback
or stop mode.
1
Marker
Marker
Marker
1
2
3
00 27 54
01
02
16 25
08 31
/Enter/Cancel/Marker
Press
1-3.
/
to select the Marker
2
3
Marker
Marker
Marker
1
2
3
00 27 54
01
02
16 25
08 31
/Enter/Cancel/Marker
Press ENTER.
Playback starts from the marked scene.
NOTES:
•
•
•
Some discs may not work with the
marking operation.
The marking is canceled when you
open the disc tray or turn the power off.
Some subtitles recorded around the
marker may fail to appear.
To Cancel the Mark
Press MARKER.
1
2
3
Press
/
to select the Marker 1-3.
Press CANCEL.
To remove this display, press MARKER.
41
2C51001AE (38-43)
41
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing soundtrack language / Subtitles / Karaoke playback
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
Changing soundtrack language
You can select the language when you play a multilingual disc.
Press AUDIO during playback.
Thecurrentsoundtracklanguage
will appear.
1
1/8 Eng DolbyDigital
Press AUDIO repeatedly until
2 the desired language is selected.
2/8 Fra DolbyDigital
The on-screen display will disap-
pear after a few seconds.
Turning the Subtitles On and Off
When playing back a disc recorded with subtitles, you can turn
the subtitles on or off.
Press SUB TITLE during playback
until “Off” appears.
Off
NOTES:
• If the desired language is not heard after
pressing the button several times, the
language is not recorded on the disc.
• Changing soundtrack or subtitle language
is cancelled when you open the disc tray
or turn the power off.The initial default lan-
guage or available language will be heard
and seen if the disc is played back again.
• Depending on the DVD you may be unable
to turn on, turn off, or change the subtitles,
even if they are recorded on the disc. While
playing the DVD, the subtitle may change
while opening or closing the disc tray, or
while changing the title.
Changing the subtitle language
You can select the language when playing back a disc
recorded with multi-lingual subtitles.
Press SUB TITLE repeatedly during
playbackuntilyourdesiredlanguage
appears.
The on-screen display will disappear
after a few seconds.
1/32 Eng
• In some cases, the subtitle language is not
changed to the selected one immediately.
• The vocal output feature is used during
playback of Dolby Digital (multi-channel)
recorded DVD KARAOKE discs. This
feature allows you to turn off vocal audio
tracks, or restore them for background
accompaniment.
Karaoke playback
When playing back a DVD KARAOKE disc, you can turn the vocal on or off.
Press AUDIO during DVD
KARAOKE disc playback.
1
1/8 Eng DolbyDigital
On
Press
or
toselect“On”or“Off”.
2
• When playing KARAOKE, connect
appropriate audio equipment such as an
amplifier to the DVD/VCR.
On: The primary vocal is output
when it is recorded on the disc.
Off: The primary vocal is not output.
42
2C51001AE (38-43)
42
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing angles / Title selection / DVD menu
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
Changing Angles
When playing back a disc recorded with multi-angle facility, you
can change the angle that you are viewing the scene from.
Press ANGLE during playback.
The current angle will appear.
1
1/9
Press ANGLE repeatedly until the desired angle is selected.
2
Title Selection
Two or more titles are recorded on some discs. If the title menu
is recorded on the disc, you can select the desired title.
Press TOP MENU during playback.
1
Title menu appears on the screen.
• PressTOPMENUagaintoresumeplaybackatthescene
when you pressed TOP MENU.
Press
/
or
/
to select the desired title.
2
3
Press ENTER or PLAY.
The playback of the selected title will start.
DVD Menu
Some DVDs allow you to select the disc contents using the
menu.
When you play back these DVDs, you can select the subtitle
language and soundtrack language,etc. using the DVD menu.
Press DVD MENU during playback.
1
The DVD menu appears on the screen.
• Press DVD MENU again to resume playback at
the scene when you pressed DVD MENU.
NOTE:
Depending on the DVD, you may not
be able to change the angles even if
multi-angles are recorded on the disc,
or you may be unable to select the title,
and a “title menu” may simply be called
a “menu” or “title” in the instructions
supplied with the disc.
Press
/
or
/
to select the desired item.
2
3
Press ENTER.
The menu continues to another screen. Repeat steps 2 and 3 to
set the item completely.
43
2C51001AE (38-43)
43
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental control
Somediscsarespecifiednotsuitable
for children. Such discs can be
prevented from play back with the
unit.
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
Parental control setting
Language Picture Sound Parental Other
Press SETUP in the stop mode.
Press or to select “Parental”.
1
Password
Parental
Off
Then press
or ENTER.
0
9/Cancel
/Enter/Setup/Return
Press
once to select “Parental Off”,
Language Picture Sound Parental Other
Password
2
3
then press ENTER until the level you
desire appears (e.g.: 1).
Parental
1
/Enter/Setup/Return
Press
once to select “Password
”.
Then press Number keys to input a 4-
digit password (e.g.: 1234).
Language Picture Sound Parental Other
Password
Parental
1234
1
• If you input a wrong number, press
CANCEL.
• Be sure to remember this number!
0
9/Cancel
/Enter/Setup/Return
Level Off :The parental control setting does not function.
Level 1 :DVD software for adults cannot be played back.
Level 8 :All DVD software can be played back.
Select from level 1 to level 8.
On a scale of 1-8, “1” is the most restrictive.
Press ENTER.
Language Picture Sound Parental Other
4
5
1234
change to
.
Password
Parental
1
0
9/Cancel
/Enter/Setup/Return
To make SETUP screen disappear, press SETUP.
NOTES:
• If each setup (page 44~51) has been
completed, the unit can always be
worked under the same conditions
(especially with DVD discs).
Each setup will be retained in the
memory if you turn the power off.
• Depending on the discs, the unit can-
not limit playback.
• Some discs may not be encoded with
specific rating level information though
its disc jacket says “adult”. For those
discs, the age restriction will not work.
• Do not forget the password. If you forget
the password, contact customer service.
To unlock the Parental control setting
Cancel the password so as to set the Parental level freely again,
Select “Password
and press Number keys to input your
4-digit password.
” (step 2)
Language Picture Sound Parental Other
1
2
Password
Parental
1234
1
Then press ENTER.
0
9/Cancel
/Enter/Setup/Return
If the input password was right,
will appear.
You can move to “Parental 1”(e.g.) to
input the desired level or to cancel
parental control.
Language Picture Sound Parental Other
Password
Parental
1
0
9/Cancel
/Enter/Setup/Return
44
2C51001AE (44-49)
44
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Temporary disabling of rating level by DVD disc
Depending on the DVD disc, the
Preparation:
disc may try to temporarily cancel
the rating level that you have set.
It is up to you to decide whether to
cancel the rating level or not.
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
LoadaDVDdiscandpressPLAY
1
or OPEN/CLOSE (see page 35).
If the DVD disc has been designed to temporarily cancel the
2
Rating level, the screen which follows the “Reading” screen will
change, depending on which disc is played. If you select “YES”
with ENTER key, “Your disc exceeds the parental control level
1.”(e.g.) screen will then appear.
Reading
Your disc exceeds
the parental control level 1.
Parental Control Level
Cancel Picture
/Enter/Return
If you wish to cancel the set rating level temporarily, select
3
“Parental Control Level” with
or
, then press ENTER. If
the 4-digits password at step 3 on page 44 has been set, the
password entering screen will appear as shown in step 4 below.
Alternatively, if the password has not been set, playback will
commence. If you don’t know (or have forgotten) the password,
select “Cancel Picture”.
The setting screen will disappear. Press OPEN/CLOSE to
remove the disc.
Enter the password with
Number buttons (0-9).
Then press ENTER.
4
5
Please enter the
4
digit password
Enter/0 9/Cancel/Return
If you interrupt the entering,
press RETURN.
Playback will commence if the entered password was correct.
NOTE:
This temporary cancellation of rating
level will be kept until the disc is ejected.
When the disc is ejected, the original
rating level will be set again
automatically.
45
2C51001AE (44-49)
45
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menu language
You can select the language of the
disc menu messages of DVDs.
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
Press SETUP in the stop mode.
Language Picture Sound Parental Other
1
2
3
Press
or
to select “Lan-
guage”.
/Enter/Setup/Return
Press
or ENTER.
Language Picture Sound Parental Other
Then press
or
to select
Menu
Subtitle
Audio
English
Automatic
English
“Menu”.
/Enter/Setup/Return
Press
Press
or ENTER.
or to select your
Language Picture Sound Parental Other
Menu
Subtitle
Audio
English
Automatic
English
English
Francais
Espanol
Other
desired language, then press
ENTER.
/Enter/Setup/Return
English, Francais, Espanol:
The selected language is the first-priority Menu language.
Other:
Other languages can be selected (See the Language code list
on page 53).
To make SETUP screen disappear, press SETUP.
4
46
2C51001AE (44-49)
46
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting subtitle language
Preparation:
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
The same subtitle language can
always be selected even if you replace
the disc or turn the power off.
•
•
Press SETUP in the stop mode.
Language Picture Sound Parental Other
1
2
3
Press
or
to select “Lan-
guage”
/Enter/Setup/Return
Language Picture Sound Parental Other
Press
or ENTER.
Then press
or
to select
Menu
Subtitle
Audio
English
Automatic
English
“Subtitle”.
/Enter/Setup/Return
Language Picture Sound Parental Other
Press
Press
or ENTER.
or to select your
Menu
Subtitle
Audio
English
Automatic
English
English
Francais
Espanol
Other
desired language, then press
ENTER.
Automatic
Off
/Enter/Setup/Return
English, Francais, Espanol:
The subtitle is displayed with the selected language if it is
recorded on the disc.
Other:
If you want to select another language, enter the language code
(See the Language code list on page 53).
Automatic:
• The unit will automatically select the same language in the
AUDIO setting.
• When the unit selects the same language as the AUDIO, the
subtitles will not appear during playback.
• When you do not use the same language as the AUDIO, the
subtitles will appear during playback.
Off:
NOTE:
Subtitles do not appear.
If the selected language is not recorded
on the disc, the first-priority language is
selected.
To make SETUP screen disappear, press SETUP.
4
47
2C51001AE (44-49)
47
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting audio soundtrack language
Thesameaudiosoundtracklanguage
can always be selected by your unit
even if you replace the disc or turn
the power off.
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
Press SETUP in the stop mode.
Press or toselect“Language”
Language Picture Sound Parental Other
1
2
3
/Enter/Setup/Return
Language Picture Sound Parental Other
Press
or ENTER.
Then press
or
to select
Menu
Subtitle
Audio
English
Automatic
English
“Audio”.
/Enter/Setup/Return
Language Picture Sound Parental Other
Press
Press
or ENTER.
or to select your
Menu
Subtitle
Audio
English
Automatic
English
English
Francais
Espanol
Other
desired Audio Language, then
press ENTER.
Original
/Enter/Setup/Return
English, Francais, Espanol:
The language you have selected will play if it is recorded on
the disc.
Other:
If you want to select another language,
enter the language code (See the Language code list on page
53).
Original:
The unit will select the first priority language of each disc.
To make SETUP screen disappear, press SETUP.
4
NOTE:
If the selected language is not recorded
on the disc, the original language will
be heard.
48
2C51001AE (44-49)
48
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the aspect ratio of TV screen
You can select the aspect ratio for
Preparation:
your TV.
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
Press SETUP in the stop mode.
Language Picture Sound Parental Other
1
2
3
Press
or
to select “Pic-
ture”.
/Enter/Setup/Return
Press
or
or ENTER, then press
to select “Tv Screen”.
Language Picture Sound Parental Other
Tv Screen
Display
4:3
On
/Enter/Setup/Return
Press
Press
or ENTER.
Language Picture Sound Parental Other
or
to select your
Tv Screen
Display
4:3
On
4:3
4:3
desired screen type, then press
ENTER.
16:9
/Enter/Setup/Return
You have the following screen sizes to choose from:
4:3 : Letter box
Select this mode when connecting to a conventional TV. When
playing back a wide screen-DVD disc, it displays the wide picture
with black bands at the top and bottom of screen.
4:3
: Pan Scan
It displays the wide picture on the whole screen with left and
right edges automatically cut off.
16:9
: Wide
Select this mode when connecting to a wide-screen TV.
A wide screen picture is displayed full size.
To make SETUP screen disappear, press SETUP.
NOTE:
4
If the DVD disc is not formatted in the pan
& scan style, it displays 4:3 style.
49
2C51001AE (44-49)
49
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting on screen display / Status display of disc
On screen display can be switched
on or off when you press the
DISPLAY button.
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
Press SETUP in the stop mode.
Language Picture Sound Parental Other
1
2
3
Press
or
to select “Picture”
/Enter/Setup/Return
Press
or
or ENTER, then press
to select “Display”.
Language Picture Sound Parental Other
Tv Screen
Display
4:3
On
/Enter/Setup/Return
Press
or ENTER to select “On”
Language Picture Sound Parental Other
or “Off”.
Tv Screen
Display
4:3
Off
/Enter/Setup/Return
On: On screen displays appears when you press any
buttons (factory setting).
Off: On screen displays do not appear when you press any
buttons except SETUP, SEARCH MODE, PLAY MODE,
MARKER and DISPLAY.
To make SETUP screen disappear, press SETUP.
4
Status display of disc
Each press of DISPLAY, the status display of the disc will appear on
the screen and change as follows.
DVD
00:34:56 01:12:33
00:34:56 01:12:33
1/99 Chapter 1/999
1/9
Title
1/8 Eng DolbyDigital
1/32 Eng
To make status display disappear, press DISPLAY again.
AUDIO
CD
34:56
71:33
Track 11/99
When you playback the CD disc, the status display will
appear on the screen and continue displaying.
50
2C51001AE (50-BACK)
50
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Dynamic Range Control
Preparation:
DRC (Dynamic Range Control) ena-
bles you to control the dynamic range
so as to achieve a suitable sound for
your equipment.
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD
indicator will light.)
Press SETUP in the stop
mode.
1
Language Picture Sound Parental Other
Press
or
to select
“Sound”.
/Enter/Setup/Return
Press
lect “DRC”.
or ENTER to se-
2
3
Language Picture Sound Parental Other
DRC
Std
/Enter/Setup/Return
Press
press
desired setting.
or ENTER, then
or to select
Language Picture Sound Parental Other
Max
Std
Min
DRC
Std
/Enter/Setup/Return
Max: Full dynamic range is increased.
Std: Full dynamic range is maintained.
Min: Dynamic range is reduced.
NOTES:
• This function works only during playback
of Dolby Digital recorded discs.
• The level of Dynamic Range Reduction may
differ depending on DVD video disc.
51
2C51001AE (50-BACK)
51
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Progressive scan
The unit supports the Progressive
scanning system as well as the
conventional interlaced scanning
system. If your TV is equipped with
component jacks which support the
progressive video input, you can en-
joy high quality picture by making the
Progressive scanning mode active.
Preparation:
• Connect to a TV equipped with component jacks.
• Turn ON the TV and set it to the corresponding video input mode.
• Set the S-VIDEO /COMPONENT video selector switch on the
rear panel to COMPONENT position.
• Press VCR/DVD to select the DVD mode. (The DVD indicator
will light.)
Press PROGRESSIVE in the stop mode. The PROGRESSIVE
indicator “ ” on the display window will light.
1
• The unit recognizes the picture source (film or video) of the
current disc according to the disc information.
Press PLAY to start playback.
2
• To make the progressive scanning mode inactive, press
PROGRESSIVE in the stop mode. The PROGRESSIVE
indicator “ ” on the display window will go off.
S-VIDEO/COMPONENT
Video selector switch
About PROGRESSIVE SCANNING MODE
To display video on the TV screen, the conventional scanning
method is called “Interlaced scanning”. With this method, only half
of the horizontal lines are displayed at a time. So two fields
complete a single picture (frame); i.e., the first field, containing all
the odd-numbered lines, is displayed followed by the second field,
containing all the even-numbered lines.
The Progressive scanning system scans all horizontal lines at a
time, so you can double the number of lines compared with the
interlaced scanning, resulting in a high-density, flicker-free picture.
Toenjoyaprogressivescannedvideo, theTVconnectedtotheunit
must have Progressive inputs.
Depending on the material source format, DVD discs can be
classified into two categories; film and video (note that some DVD
discs contain both a film source and a video source). Film sources
are recorded as 24-frame-per-second information, while (NTSC)
video sources are recorded as 30-frame-per second (60-field-per-
second interlaced) information.
When the unit plays back a film source material, uninterlaced
progressiveoutputsignalsarecreatedusingtheoriginalinformation.
When a video source material is played back, the unit interleaves
linesbetweentheinterlacedlinesoneachtocreatetheinterpolated
picture and outputs as the progressive signal.
NOTES:
• Some discs may not be played back with the progressive scanning mode correctly because of the disc
characteristics or recording condition.
• There are some progressive TV and High-Definition TV sets that are not fully compatible with the unit, resulting
in the unnatural picture when playing back a DVD disc in the Progressive scanning mode. In such a case, use the
Interlaced scanning mode.
• You cannot make the progressive scanning mode active in following cases.
– The unit is in the VCR mode.
– The disc is played back in the DVD mode.
– The S-VIDEO/COMPONENT video selector switch is set to S-VIDEO position.
52
2C51001AE (50-BACK)
52
18/11/03, 2:39 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Language code list
Enter the appropriate code number for the initial settings “Audio”, “Subtitle” and/or “Menu” (see pages
46-48).
Language Name Code Language Name Code Language Name Code Language Name Code
Abkhazian
Afar
1112 Fiji
1620 Lingala
1619 Lithuanian
1628 Macedonian
1635 Malagasy
1722 Malay
2224 Singhalese
2230 Slovak
2321 Slovenian
2317 Somali
2329 Spanish
2322 Sundanese
2330 Swahili
2319 Swedish
2328 Tagalog
2325 Tajik
2919
2921
2922
2925
1529
2931
2933
2932
3022
3017
3011
3030
3015
3018
1225
3019
3025
3028
3021
3033
3121
3128
3136
3219
3225
1335
3325
3418
2019
3525
3631
1111 Finnish
1116 French
2927 Frisian
1123 Galician
1128 Georgian
1835 German
1129 Greek
Afrikaans
Albanian
Amharic
Arabic
2111 Malayalam
1415 Maltese
1522 Maori
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
1135 Greenlandic
1136 Guarani
1211 Gujarati
1531 Hausa
2122 Marathi
1724 Moldavian
1731 Mongolian
1811 Nauru
2324 Tamil
Basque
2411 Tatar
Bengali; Bangla 1224 Hebrew
1933 Nepali
2415 Telugu
2425 Thai
Bhutani
Bihari
1436 Hindi
1819 Norwegian
1831 Oriya
1218 Hungarian
1228 Icelandic
1217 Indonesian
2335 Interlingua
1215 Irish
2528 Tibetan
2611 Tigrinya
Breton
1929 Panjabi
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
1924 Pashto, Pushto 2629 Tonga
1911 Persian
1711 Polish
1611 Turkish
2622 Turkmen
2630 Twi
2123 Italian
1930 Portuguese
2011 Quechua
1311 Japanese
3618 Javanese
1325 Kannada
1828 Kashmiri
1329 Kazakh
1411 Kirghiz
2422 Korean
1524 Kurdish
1525 Laothian
1530 Latin
2731 Ukrainian
2033 Rhaeto-Romance 2823 Urdu
2124 Romanian
2129 Russian
2121 Samoan
2135 Sanskrit
2125 Scots Gaelic
2131 Serbian
2825 Uzbek
2831 Vietnamese
2923 Volapük
2911 Welsh
1714 Wolof
Danish
Dutch
English
2928 Xhosa
Esperanto
Estonian
Faroese
2225 Serbo-Croatian 2918 Yiddish
2211 Shona
2924 Yoruba
2914 Zulu
1625 Latvian, Lettish 2232 Sindhi
53
2C51001AE (50-BACK)
53
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and troubleshooting
Use the following check list for troubleshooting when you have problems with your unit. Consult your local
dealer or service outlet if problems persist.
Be sure all connections are properly made when using with other units.
SYMPTOMS
DVD/VCR
POSSIBLE SOLUTIONS
PAGE
•Make sure the power cord is plugged in.
•Try another AC outlet.
•Power is off, check fuse or circuit breaker.
•Unplug unit, then plug it back in.
5
–
–
DVD/VCR does not operate.
5
•Select the DVD or VCR mode before operating.
18,34
•
Antenna connection is not correct or antenna cable is disconnected.
12~15
18
• The video channel is not in the correct position or the TV is not
set to the video channel 3 or 4.
No picture.
No sound.
• Check the unit is connected correctly.
• The video input selector of the TV is not set to VIDEO. Set to
VIDEO (or equivalent).
12~17
–
• Channel is set to the external mode.
–
• Check the unit is connected correctly.
• Check the input selector of the amplifier is set properly.
• The unit is in the Special playback mode.
12~17
–
24,36
• Aim at the remote control at the remote sensor.
• Operate within Approx. 5 Meters or reduce the light in the room.
• Clear the path of the beam.
• The batteries are weak. Replace the batteries.
• Check the batteries are inserted correctly.
The remote control does not
function.
11
•Check all CATV connections.
•Station or CATV system problems, try another station.
14,15
No CATV reception.
VCR
•The erase prevention tab of the video cassette is broken off.
•The unit is in the external input mode.
TV recording does not work.
22,26
• The time is not set correctly.
• The recording start/end time is not set correctly.
• TIMER REC has not been pressed ( is not lit).
19
29
29
Timer recording does not work.
• Tracking adjustment beyond range of automatic tracking circuit.
Try Manual tracking adjustment.
• Video heads are dirty.
24
Noise bars on screen.
55
–
• The tape is worn or damaged.
DVD
Display is not shown in your
language.
•Select proper language in the menu options.
34
• No disc is inserted.
• The disc may be dirty. Clean up the disc.
• The unit cannot play DVD-ROMs, etc.
35
33
33
Playback doesn’t start.
Stopping playback, search, slow-
motion play, repeat play, or
program play, etc. cannot be
performed.
• Some discs may not do some of the functions.
–
54
2C51001AE (50-BACK)
54
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and troubleshooting / Video head cleaning
SYMPTOMS
POSSIBLE SOLUTIONS
PAGE
• The S-VIDEO/COMPONENT selector is not set correctly.
• The progressive scanning mode is active through the unit is
connected to a TV via the VIDEO OUT jack.
16
52
No picture, or the screen is blurred
or divided into two parts.
No 4:3 (16:9) picture.
No on-screen display.
No surround sound.
• The setup does not match your TV.
• Select Display On.
49
50
17
• The setup does not match your stereo system.
The unit or remote operation key
is not functioning.
• Turn off the unit and unplug the AC power cord for several
minutes, then replug it.
–
Playback does not start when the
title is selected.
• Check the Parental setup.
44
Audio soundtrack and/or subtitle
language is not changed when
you play back a DVD.
47,48
• Multilingual language is not recorded on the DVD disc.
• Some discs have no subtitles.
• Subtitles are cleared. Press SUB TITLE.
42,47
No subtitle.
Angle cannot be changed.
appears on the screen.
• Multi-angles are not recorded on the DVD disc.
43
–
• The function is prohibited with the unit or the disc.
Video head cleaning
Video head clogging
The video heads are the means by which the DVD/VCR reads
the picture from the tape during playback. In the unlikely event
that the heads become dirty enough to be clogged, no picture
will be played back. This can easily be determined if, during
playback of a known good tape, there is good sound, but no
picture (picture is extremely snowy). If this is the case, have
the DVD/VCR checked by qualified service personnel.
Good Picture
Snowy Picture
NOTES: DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE
•
REAR COVER.
Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.
To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.
•
•
For additional set-up or operating assistance, please visit our WEBSITE at www.memorexelectronics.com
or contact CUSTOMER SERVICE at 1-800-919-3647
Please keep all packaging material for at least 90 days in case you need to return this product to your
place of purchase or Memorex.
FOR PARTS AND ACCESSORIES, CONTACT FOX INT'L AT 1-800-321-6993
55
2C51001AE (50-BACK)
55
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
GENERAL
Power supply:
AC 120 V 60 Hz
Power consumption:
Operation: 18 W
Stand by: 2 W
Weight:
7.9 lbs (3.6 kg)
Dimensions:
Width : 16-15/16 inches (430 mm)
Height: 3-7/8 inches (99 mm)
Depth : 9-15/16 inches (253 mm)
Inputs/Outputs:
Video:
In: 1 Vp-p/75 ohm
Out: 1 Vp-p/75 ohm
Audio:
In: –8 dBm/50k ohm
Out: –8 dBm/1k ohm
UHF/VHF IN/OUT: 75 ohm coaxial
Antenna:
Hi-Fi frequency response: 20 Hz to 20,000 Hz
Hi-Fi dynamic range:
More than 90 dB
VCR section
Video head:
Audio track:
Tuner:
4 Rotary Heads
Hi-Fi Sound - 2 Tracks / MONO Sound - 1 Track
181 Channel Freq. Synthesized
VHF
UHF
2-13
14-69
CATV 14-36 (A)-(W)
37-59 (AA)-(WW)
60-85 (AAA)-(ZZZ)
86-94 (86)-(94)
95-99 (A-5)-(A-1)
100-125 (100)-(125)
01 (5A)
RF channel output:
F.FWD/REW Time:
Channel 3 or 4, Switchable
Approx. 1minute and 48 seconds (with T-120 Cassette Tape)(at+25˚C)
DVD section
Signal system:
NTSC
Applicable disc:
Audio characteristics
frequency response:
DVD (12 cm, 8 cm), CD (12 cm, 8 cm)
DVD: 4 Hz - 22 kHz
CD: 4 Hz - 20 kHz
S/N Ratio:
90 dB
Harmonic distortion:
Wow and flutter:
Dynamic range:
Output:
0.02%
Less than 0.01% Wrms
More than 90 dB
Video : (RCA) 1 Vp-p/75 ohm
Audio : (RCA) –12 dBm/1k ohm
Digital Audio : 0.5 Vp-p/75 ohm
CD : Wavelength: 775 - 805 nm
Maximum output power: 0.5 mW
DVD : Wavelength: 640 - 660 nm
Maximum output power: 1.0 mW
Pickup:
ACCESSORIES:
Remote control x 1
75 ohm Coaxial Cable x 1
AUDIO/VIDEO Cable x 1
56
2C51001AE (50-BACK)
56
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
57
2C51001AE (50-BACK)
57
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
ESPAÑOL
El símbolo del rayo dentro de un
triángulo equilátero tiene por finalidad
alertar al usuario acerca de la presencia
de tensión peligrosa (sin aislación) en el
interior del producto, que puede tener la
intensidad suficiente como para constituir
un riesgo de descarga eléctrica.
PRECAUCION
RIESGO DE DESCARGA
ELECTRICA NO ABRIR
AVISO: PARA REDUCIR EL RIESGO DE DESCARGA
ELECTRICA, NO RETIRE LA CUBIERTA (O POSTE-
RIOR). EN EL INTERIOR DEL APARATO NO HAY
COMPONENTE ALGUNO QUE PRECISE SERVICIO DE
MANTENIMIENTO A CARGO DEL USUARIO.SOLICITE
CUALQUIER OPERACION DE MANTENIMIENTO A
PERSONAL DE SERVICIO CALIFICADO.
El signo de exclamación dentro de un
triángulo equilátero tiene por finalidad
alertar al usuario de importantes
instrucciones de operación
y
mantenimiento (servicio) en la literatura
que acompaña a este aparato.
AVISO: Para reducir el riesgo de incendio o descarga eléctrica, no exponga esta unidad a la lluvia ni a la
humedad.
NOTA: Por favor guarde todo el material de embalaje durante por lo menos 90 días en caso de que
necesite devolver este producto a su lugar de compra o Memorex.
ADVERTENCIA: Este equipo ha sido sometido a pruebas y cumple con los límites establecidos para un
aparato digital de Clase B, de acuerdo con la Parte 15 del Reglamento de la FCC. Estos
límites están diseñados para proporcionar protección razonable contra interferencias
perjudiciales en una instalación residencial. Este equipo genera o emplea energía de
radiofrecuencia y, si no es instalado y empleado de acuerdo con estas instrucciones, puede
causar interferencias perjudiciales a las radiocomunicaciones.
Sin embargo, no garantizamos que no ocurrirán interferencias en una instalación en
particular. Si este equipo causa interferencias perjudiciales a la recepción radial o televisiva,
situación que puede ser determinada apagando y encendiendo el equipo, se sugiere al
usuario que trate de corregir tal interferencia mediante una o más de las siguientes medidas:
- Reorientar o relocalizar la antena receptora.
- Incrementar la separación entre el equipo y el receptor.
- Conectar el equipo a un tomacorriente o circuito diferente al que está conectado al receptor.
- Consultar con el concesionario o un técnico experimentado solicitándole su asistencia.
PRECAUCION: El usuario corre el riesgo de perder la autorización para hacer funcionar este equipo en caso
de que ejecute un cambio o modificación no aprobado por la parte responsable para la
conformidad con las Reglas FCC.
PRECAUCION:
ESTE TOCADISCOS DE VIDEO DIGITAL UTILIZA UN SISTEMA LASER.
PARA UTILIZAR CORRECTAMENTE ESTE PRODUCTO, LEA CUIDADOSAMENTE ESTE MANUAL DE
INSTRUCCIONES Y GUARDELO PARA SU REFERENCIA EN EL FUTURO. SI FUERA NECESARIO
HACER UN MANTENIMIENTO DE ESTE APARATO, CONSULTE CON UN CENTRO DE SERVICIO
AUTORIZADO-LEA EL PROCEDIMIENTO DE SERVICIO.
EL USO DE LOS CONTROLES, AJUSTES O LA REALIZACION DE OTROS PROCEDIMIENTOS QUE NO
SEAN LOS ESPECIFICADOS AQUI PUEDE PROVOCAR UNA EXPOSICION A RADIACIONES
PELIGROSAS.
PARA EVITAR LA EXPOSICION DIRECTA A LOS RAYOS LASER, NO TRATE DE ABRIR LA CAJA. PUEDE
HABER UNA RADIACION LASER VISIBLE AL ABRIR LA CAJA.
NO MIRE HACIA EL RAYO.
Lugar de la marca requerida
La hoja de especificaciones y las precauciones para su seguridad
están en la parte trasera del aparato.
CERTIFICACION: CUMPLE CON LAS NORMAS DE PRESTACIONES
CON RADIACION DE LA FDA, 21 CFR SUBCAPITULO J.
2
2C51001AS(02-05)
2
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
PARA SU SEGURIDAD
1. LEA LAS INSTRUCCIONES
Antes de usar la unidad, lea detenidamente todas las instrucciones de seguridad y operación.
2. CONSERVE ESTE MANUAL DE INSTRUCCIONES
Conserve las instrucciones de seguridad y operación para consultas futuras.
3. RESPETE LAS ADVERTENCIAS
Observe estrictamente todas las advertencias impresas en la unidad y las incluidas en el manual de instrucciones.
4. SIGA LAS INSTRUCCIONES
Siga todas las instrucciones de operación y uso.
5. LIMPIEZA
Antes de limpiar este videograbador, desconéctelo del tomacorriente mural. No use limpiadores líquidos ni
aerosol. Utilice sólo un paño húmedo para limpiar el exterior del mueble.
6. ENCHUFES
El fabricante de esta unidad no hace ninguna recomendación de accesorios ya que pueden ser peligrosos.
7. AGUA Y HUMEDAD
No utilice este aparato cerca del agua. Por ejemplo cerca de una bañera, lavabo, pileta de la cocina,
lavadero, en un sótano húmedo o cerca de una piscina.
AVISO PARA CARRO PORTATIL
(símbolo provisto por RETAC)
8. ACCESORIOS
No instale esta unidad en un carro, soporte, trípode o mesa inestables.
La unidad podría caerse, causando serias lesiones, resultando también
severamente dañada a la unidad.
8A. La combinación de aparato y carro deberá ser movida con cuidado.
Las detenciones bruscas, la fuerza excesiva y las superficies disparejas
podrán hacer que el aparato y el carro se vuelven.
9. VENTILACION
S3125A
Las ranuras y aberturas en la parte trasera o inferior del mueble son para
ventilación permiten un funcionamiento fiable de la unidad, protegiendo contra calentamiento excesivo.
Estas aberturas no deberán ser bloqueadas ni cubiertas. Para evitar bloquear las aberturas, nunca sitúe la
unidad encima de una cama, sofá, alfombra u otra superficie similar. Tampoco instale la unidad cerca o
encima de un radiador o calefactor. La unidad no deberá ser instalado en un mueble empotrado, como ser
una repisa para libros o bastidor, a menos que se pueda garantizar una ventilación adecuada, y/o cuando
las instrucciones del fabricante así lo especifiquen.
10. FUENTES DE ALIMENTACION
Esta unidad sólo deberá ser operada mediante el tipo de fuente de alimentación
especificado en la etiqueta indicadora. Si no está seguro del tipo de fuente de
alimentación que tiene en su casa, consulte a su distribuidor o a la
compañía de electricidad local. En el caso de unidades diseñadas para
funcionar a pilas o con otras fuentes de alimentación, consulte el manual de instrucciones respectivo.
11. CONEXIÓN A TIERRA O POLARIZACION
Esta unidad está equipada con una clavija polarizada de corriente alterna (una clavija que tiene una espiga
más ancha que la otra). Esta clavija solamente puede ser insertada en el tomacorriente en una sola
dirección. Esta es una medida de seguridad. Si no pudiera insertar completamente la clavija en el
tomacorriente, vuelva a intentarlo invirtiendo la clavija. Si aún no fuera posible insertar la clavija, tome
contacto con un electricista para que reemplace su tomacorriente obsoleto. Si su unidad está equipada con
una clavija de conexión a tierra de 3 alambres (una clavija con una tercera espiga de conexión a tierra), no
modifique las características de seguridad de la clavija polarizada. Este tipo de clavija sólo puede ser
insertado en un tomacorriente con contacto a tierra. Esto también es una medida de seguridad. Si no
pudiera insertar la clavija en el tomacorriente, tome contacto con un electricista para que reemplace su
tomacorriente obsoleto. No modifique las características de seguridad de la clavija de conexión a tierra.
3
2C51001AS(02-05)
3
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
PARA SU SEGURIDAD
12. PROTECCION DEL CABLE DE ALIMENTACION
Los cables de alimentación deberán ser tendidos de manera tal que la probabilidad de que sean pisados o
aplastados por otros objetos sea mínima. Preste especial atención a las clavijas de los cables, a los
receptáculos, y al punto por donde salen del aparato.
13. TORMENTAS ELECTRICAS
Como medida de protección durante tormentas eléctricas, o cuando el videograbador permanezca sin uso
durante períodos prolongados de tiempo, desconéctelo del tomacorriente mural y desconecte la antena o
el sistema de cable. Esto evitará que la unidad resulte dañada por tormentas eléctricas o sobretensiones
en la línea de alimentación.
14. LINEAS DE ALIMENTACION
Una antena exterior no deberá ser instalada en la cercanía de líneas de alimentación aéreas ni de otros
circuitos de iluminación eléctrica o potencia, o donde pueda caerse y hacer contacto con tales líneas o
circuitos. Al instalar un sistema de antena exterior, tenga mucho cuidado de no tocar tales líneas o circuitos
de alimentación, ya que el contacto con ellos podría ser fatal.
15. SOBRECARGA
No sobrecargue los tomacorrientes murales ni los cables de extensión, ya que esto podría causar
incendios o descargas eléctricas.
16. ENTRADA DE OBJETOS Y LIQUIDOS
Nunca introduzca objetos de ningún tipo por las aberturas de la unidad, ya que podría tocar peligrosos
puntos de alta tensión o piezas de cortocircuito, provocando incendios o descargas eléctricas. Nunca
derrame ni rocíe ningún tipo de líquido sobre la unidad.
17. CONEXION ATIERRA DE LA ANTENA EXTERIOR
Si se conecta una antena externa o sistema de cable a la unidad, cerciórese de que el sistema de antena o
cable está conectado a tierra para darle protección contra sobretensión y acumulación de carga estática.
La Sección 810 del Código Nacional de Electricidad, ANSI/NFPA 70, entrega información acerca de la
manera correcta de conectar a tierra el mástil y la estructura soportante, puesta a tierra del alambre de
entrada a una unidad de descarga de antena, tamaño de los conductores de puesta a tierra, ubicación de la
nidad de descarga de la antena, conexión a los electrodos de tierra, y requisitos para el electrodo de tierra.
18. SERVICIO
No intente reparar la unidad usted mismo; al abrir o retirar las cubiertas usted se expondrá a alta tensión y
a otros peligros. Solicite todo servicio a personal calificado.
19. DAÑOS QUE REQUIERAN REPARACION
En los siguientes casos, desconecte la unidad del tomacorriente mural y llame a un técnico de servicio
calificado:
a. Cuando el cable de alimentación o la clavija estén dañados.
b. Si se ha derramado líquido sobre la unidad, o si algún objeto ha caído dentro del videograbador.
c. Si la unidad ha sido expuesta a la lluvia o al agua.
d. Cuando a pesar de haber seguido las instrucciones de operación, la unidad no funcione normalmente.
Ajuste solamente los controles indicados en el manual de instrucciones; el ajuste incorrecto de otros
controles podrá causar daños a la unidad, la que por lo general requerirá de un prolongado trabajo
de reparación (por un técnico calificado) para que sus condiciones normales de operación puedan
ser restablecidas.
e. Si la unidad se ha caída o si el gabinete se ha dañado.
f. Cuando la unidad muestre un cambio notorio en su rendimiento.
20. PIEZAS DE REPUESTO
Cuando sea necesario reemplazar piezas, asegúrese de que el técnico de servicio emplee las piezas de
repuesto especificadas por el fabricante, o piezas que tengan las mismas características que las piezas
originales. Los cambios no autorizados podrán causar incendios, descargas eléctricas y otros problemas.
21. REVISION DE SEGURIDAD
Al finalizar cualquier servicio de mantenimiento o reparación de esta unidad, solicítele al técnico que
efectúe comprobaciones de seguridad para determinar si el videograbador se encuentra o no en
condiciones óptimas de operación.
22. CALOR
El producto debe ser situado lejos de fuente de calor como radiadores, reguladores de calefacción, estufas o
otros productos (incluyendo amplificadores) que se producen calor.
23. BANDEJA DEL DISCO
No acerque sus dedos a la bandeja del disco cuando se está cerrando. Puede recibir heridas graves.
24. CONEXION
Cuando conecte el producto a otro equipo, desconecte la alimentación y desenchufe todos los equipos del
tomacorriente. Si no lo hace, puede provocar una descarga eléctrica y heridas graves.
Lea cuidadosamente el manual de instrucciones del otro equipo y respete las instrucciones al hacer las
conexiones.
4
2C51001AS(02-05)
4
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
PARA SU SEGURIDAD/Fuente de alimentación
25. RAYO LASER
No mire por la ranura de la bandeja del disco por las salidas de circulación de aire del producto para ver la
fuente del rayo láser. Puede dañar sus ojos.
26. DISCO
No utilice un disco rayado, deformado o reparado. Estos discos se pueden romper fácilmente y provocar
serias heridas o averías en el producto.
27. NOTA PARA LA PERSONA QUE INSTALE EL SISTEMA CATV
Se ha incluido este recordatorio para llamar la atención de quien instale el sistema CATV, con respecto al
Artículo 820-40 de la NEC, que entrega directivas de guía para realizar una conexión adecuada a tierra y,
en particular, especifica que el cable de puesta a tierra debe ser conectado al sistema de conexión a tierra
del edificio, lo más cerca del punto de entrada del cable como sea posible.
EJEMPLO DE CONEXION A TIERRA DE LA ANTENA
SEGUN EL CODIGO NACIONAL DE ELECTRICIDAD
ALAMBRE DE ENTRADA DE LA ANTENA
ABRAZADERA
DE TIERRA
UNIDAD DE DESCARGA DE LA ANTENA
(NEC, SECCION 810-20)
CONDUCTORES DE PUESTA A
TIERRA (NEC, SECCION 810-21)
EQUIPO DE SERVICIO
ELECTRICO
ABRAZADERAS DE TIERRA
SERVICIO DE ALIMENTACION DE SISTEMA
ELECTRODO DE PUESTA A TIERRA
(NEC ART 250, PARTE H)
NEC - CODIGO NACIONAL DE ELECTRICIDAD
S2898A
CONDENSACION
Se condensará humedad en la sección de funcionamiento del DVD/VCR si se lo trae de un lugar fresco a una
habitación caliente o si la temperatura en la habitación sube repentinamente. En este caso, se verán afectadas
las prestaciones del DVD/VCR. Para evitarlo, deje el DVD/VCR a la nueva temperatura durante
aproximadamente una hora antes de conectarlo, o haga que la temperatura en la habitación suba gradualmente.
También puede condensarse humedad durante el verano si el DVD/VCR está expuesta a una corriente de aire
del acondicionador de aire. En estos casos, cambie el lugar donde está instalado el DVD/VCR.
Fuente de alimentación
PARA UTILIZAR CORRIENTE ALTERNA (CA)
Tomacorriente de CA
Utilice el cable de CA polarizado sumistrado para CA operación. Conecte
el enchufe pequeño en el extremo del cable al conectador de entrada de
CA en el parte trasera del DVD/VCR, luego inserte el enchufe más ancho
de cable de CA en un tomacorriente de CA de 120V, 60Hz polarizado.
Orificio y hoja
más anchos
NOTAS:
• Nunca conecte el enchufe cordon de CA a otro voltaje que no sea el
especificado (120V 60Hz).
Utilice solamente el cordon eléctrico suministrado.
• Si el cordon de CA polarizada no se ajusta en un tomacorriente de CA
no polarizada, no intente limar o cortar las clavijas.
Es responsabilidad de usuario hacer que un electricista reemplace el
tomacorriente inadecuado.
Cable de corriente alterna polarizado
(una pata es más ancha que la otra.)
• Si usted causa una descarga estática cuando toca la undad y este falla,
simplemente desenchufe la unidad del tomacorriente, espere algunos
minutos y enchufela otra vez. La unidad deberá funcionar normalmente.
5
2C51001AS(02-05)
5
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Caracteristicas
Reproductor de DVD/CD / Videograbador
• Reproductor de DVD/CD con videograbador - Exclusivo diseño que combina un reproductor de DVD/CD y un
videograbador Hi-Fi y ofrece un considerable ahorro de espacio. El disco DVD posee mucha más capacidad, aunque
tiene el mismo tamaño que un CD. La calidad de imagen es superior a la Super VHS. La calidad de audio es superior a
la de un CD de audio. El reproductor de DVD puede reproducir discos CD de audio.
• Alta calidad de imágenes - Más de 500 líneas (modo VCR: 230 líneas) de resolución horizontal. Supera la resolución
de Super VHS (400 líneas) o Laser Disc (430 líneas).
Sección VCR
• Recepción estéreo/SAP - Esta TV fue diseñada para recibir transmisiones segundo programa de sonido (SAP) y
en estéreo cuando existen.
• 4 cabezas de video - Proporcionan una calidad de imagen óptima para la reproducción de efectos especiales.
• Cabeza de 19µm - Ofrece calidad de imagen superior incluso en modo SLP, la tecnología de 19 micras de anchura
ayuda a evitar interferencias y aumenta la calidad de la imagen SLP hasta aproximarla a los niveles de la imagen SP.
Gracias a la tecnología de precisión se consigue la práctica eliminación de imágenes fantasma y de manchas de color.
• Sonido estéreo de alta fidelidad (HI-FI) - Con respuesta de frecuencia de 20 a 20,000 Hz y rango dinámico
mejor que 90 dB, este VCR brinda un nivel de excelencia que está al nivel de los discos compactos.
• Grabación por temporizador de un solo toque (OTR) - Simplemente presionando el botón REC/OTR, el
videograbador se podrá programar para un máximo de 6 horas de grabación con un comienzo inmediato.
Sección DVD
• Compatible con una gran gama de salidas de audio DVD
Toma de audio digital (Óptico o Coaxial):
• Cuando se conecta un equipo con un decodificador Dolby Digital integrado, los sonidos en Dolby Digitalpueden
producir el efecto de estar en un cine o en una sala de conciertos.
• Audio surround estándar diferente al Dolby Digital. Este formato ya se utiliza en varios cines. Al conectar esta
unidad a un decodificador DTS o a un amplificador AV con decodificador DTS integrado, se puede disfrutar del
audio DTS de los discos DVD grabados en este formato. Sin embargo, el audio no saldrá de los jacks análogos de
salida de audio.
• El podrádisfrutar del audio MPEG de los discos DVD que están grabados en este formato.
• El sonido PCM Lineal de 48 kHz/16 bit por 96 kHz/24 bit supera el sonido de los discos compactos de audio.
• Exploración progresiva - La exploración progresiva presenta al mismo tiempo todas las líneas horizontales de una
imagen, como un solo fotograma. Esta unidad convierte el vídeo entrelazado (480i) de DVD al formato progresivo
(480p) para realizar una conexión a una pantalla progresiva, aumentando la resolución vertical.
• Múltiples idiomas - Dado que este DVD admite 124 idiomas-subtítulos/-bandas sonoras, siempre podrá disfrutar de
su selección favorita. (No es posible seleccionar un idioma que no esté grabado en el disco.)
• Múltiples ángulos - Las imágenes de los deportes o conciertos en vivo se graban con muchas cámaras. Cuando
reproduzca estos discos, puede cambiar de ángulo durante la reproducción. (No es posible seleccionar múltiples
ángulos si no están grabados en el disco.)
• Reproducción repetida - Se puede repetir el capítulo, canción, título, lados o el material entre dos puntos
seleccionados.
• Reproducción de programas/aleatoria (CD) - Puede reproducir pistas en secuencias de programas o
seleccionadas aleatoriamente.
• Zoom - Se puede acercar con un zoom sobre el sujeto seleccionado en la escena durante la reproducción.
• Relación de aspecto del video - Puede cambiar la relación de aspecto de la pantalla de acuerdo al formato de su
monitor/televisor en un disco apropiado.
•
Control para mayores de edad - Puede restringir la reproducción de escenas o sonidos de los discos DVD para
mayores de edad, que tienen un nivel de control por los padres.
Este producto incorpora una tecnología de protección de derechos de autor, que a su vez está protegida
pordeterminadas patentes de los EE UU y otros derechos de propiedad intelectual propiedad de
MacrovisionCorporation y otros propietarios de dichos derechos. El uso de esta tecnología protegida por los derechos
de autor debe estar autorizada por Macrovision Corporation y es exclusivamente para uso doméstico y otros usos
limitados a menos que sea autorizado de otra manera por Macrovision Corporation.
*
Se prohibeel desarmado y el estudio de su diseño para copiarlo.
Fabricado bajo licencia de Dolby Laboratories. “Dolby” y el símbolo de la doble D son marcas comerciales de Dolby
Laboratories.
*
“DTS” y “DTS Digital Out” son marcas registradas de Digital Theater Systems, Inc.
*
*
La grabación no autorizada de programas de televisión con derechos de autor, película, video cassettes y otros
materiales, puede infringir la ley de derechos autorales y ser contraria a las leyes pertinentes.
6
2C51001AS(06-11)
6
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Indice
Antes de utiliaear su aparato
Reproducción de discos
PARA SU SEGURIDAD ...................................3
Fuente de alimentación....................................5
Caracteristicas .................................................6
Indice................................................................7
Partes y sus funciones .....................................8
Visualizador......................................................9
Control remoto ...............................................10
Conexiones basicos .......................................12
Conexiones de TV cable (CATV) ...................14
Conexión para reproducción ..........................16
Disco .............................................................. 33
Ajuste de la selección de idioma.................... 34
Procedimiento de reproducción ..................... 35
Reproducción especial................................... 36
Zoom .............................................................. 37
Búsqueda de la escena deseada................... 37
Reproducción repetida ................................... 38
Programacion de reproduccion/
Reproducción aleatoria (disco compacto)........39
Reproducción de MP3 ................................... 40
Marcación de escenas deseadas................... 41
Cambio del idioma de la pista de sonido ....... 42
Cambio del idioma de los subtítulos ...................... 42
Reproducción de karaoke .............................. 42
Cambio de ángulos............................................. 43
Selección de título.......................................... 43
Menú DVD...................................................... 43
Ajuste de la sección VCR
Ajuste del canal de video ............................... 18
Seleccion de idioma en pantalla .................... 18
Ajuste del reloj manual ................................... 19
Ajuste del sintonizador ................................... 20
Borrado de un canal de la memoria ....................... 21
Eliminacion de buido ...................................... 21
Colocación y extracción de videocassettes ... 22
Funciones avanzadas de la sección DVD
Ajuste de restricciones para menores............ 44
Deshabilitación temporal del nivel de rating
(clasificación) del disco DVD ...........................45
Selección del idioma del menú ...................... 46
Selección del idioma de los subtítulos ........... 47
Selección del idioma de la pista de
Reproducción de cintas
Reproducción de cintas de cassette .............. 23
Reproduccion especial ................................... 24
Función VUELTA A CERO.............................. 25
Sistema de búsqueda de índices de vídeo .... 25
sonido de audio.............................................. 48
Ajuste de la relación de aspecto de la
Grabacion
pantalla de TV ................................................ 49
Selección de las indicaciones en la pantalla.. 50
Datos del status del Disco.............................. 50
Control de la Gama Dinámica ........................ 51
Exploración progresiva................................... 52
Grabacion de un programa de TV.................. 26
Grabacion por temporizador de un solo toque
(OTR) ............................................................. 28
Grabacion por temporizador .......................... 29
Funciones avanzadas de la sección VCR
Información adicional
Grabacion y reproduccion estereofonicas...... 31
Segundo programa de sonido (SAP) ..................... 31
Duplicacion de una cinta de video ......................... 32
Lista de códigos de idiomas........................... 53
Problemas y localización de averías .............. 54
Limpieza de la cabeza de video..................... 55
Especificaciones ............................... TRASERA
7
2C51001AS(06-11)
7
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Partes y sus funciones
Delantera
Botón selector de modo VCR/DVD
Botón PLAY
Apertura para carga de la cinta
Botón STOP
Botón OPEN/CLOSE
Botón EJECT
Bandeja del disco
POWER
Sensor de control remote
Botónes CHANNEL L / M
Botón POWER
Indicador DVD
Botón REW
Botón REC/OTR
Tomas AUDIO (L/R)/
VIDEO IN Indicador VCR
Botón F.FWD
Ventana de la pantalla
Trasera
Toma DVD COAXIAL
DIGITAL AUDIO OUT
Cordón de CA
Conector de
entrada de RF
Conector de
salide de RF
Toma DVD S-VIDEO
OUT
Tomas DVD AUDIO
(L/R) OUT
Interruptor Selector de Toma DVD OPTICAL DIGITAL
COMPONENT/S-VIDEO AUDIO OUT (tapa protectora)
Tomas AUDIO (L/R)/VIDEO OUT comunes de
DVD/VCR
Tomas DVD COMPONENT OUT
8
2C51001AS(06-11)
8
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Visualizador
Ventana de la pantalla
1
2
3
4
12
5
6
11
10
9
8
7
No. Visualizador
Descripciones
1
2
3
4
5
6
VCR
Modo VCR
Reproducción (se ilumina) / Continuación automática (parpadea)
Imagen fija
Se coloca el disco DVD
DVD
CD
Se coloca el disco compacto
PM
Visualizador de tarde (se apaga por la mañana)
Visualizador de reloj (los dos puntos [ : ] parpadean)
10 : 00
01 : 00
2
Visualizador de contador por hora/minuto en VCR/DVD y por minuto/segundo en CD
Visualizador de número de pista para CD
Visualizador de canal de TV para VCR
Visualizador de canal de CATV
7
CH02
C036
L
Visualizador de entrada externa
Visualizador de Error
Err
Modo de exploración progresiva
8
9
Visualizador de grabación por temporizador
Videocassette en la unidad
10
11
Visualizador de pista para CD
TRK
REC
Visualizador de grabación normal (Parpadea durante la grabación por
temporizador de un solo toque, OTR)
12
NOTA:
Es posible que algunos discos se muestren de forma equivocada o que, por ejemplo, no se muestre la
información de número de capítulo, tiempo de reproducción, etc.
9
2C51001AS(06-11)
9
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Control remoto
Página
18
POWER
EJECT
Conexión/Desconexión
Expulsar videocassette
Abra o cierre la bandeja
22
OPEN/CLOSE
VCR/DVD
0-9
35
Cambiar a funcionamiento de VCR o DVD 18,34
Dirigir selección de canales de la TV
Introducir ajuste
21,26,28
37,39
44,45
27
Entre una contraseña
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
DISPLAY/CALL
Consultar información de la VCR
Consultar información del DVD
Cambiar entre TV/AV
50
DISPLAY/CALL
1
4
7
2
5
8
3
6
INPUT SELECT
PROGRESSIVE
32
Activar el modo de exploración progresiva
Seleccionar canal de TV o VCR
Botones de cursor
52
26,28
34
INPUT SELECT/
PROGRESSIVE
CH
/
L / M
TRACKING/SET –/+ Botones de ajuste
29,30
9
0
Botones de seguimiento manual en modo de reproducción 24
/
Botones de cursor
18
CH
SELECT/ENTER Introducir información en el menú
18
TRACKING/
TRACKING/
SET
–
SET
+
Seleccionar opciones del menú
34
DVD MENU
Seleccionar menú de disco DVD
43
SELECT/
ENTER
SET UP/VCR MENU Mostrar el menú de la VCR
CLEAR/CANCEL Borrar programa de temporizador
Resetear información en el menú
18,34,44,46-51
30
19,29,37,39
34
CH
RETURN
MARKER
ZOOM
Mostrar el menú del DVD
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
Indice
41
Zoom (para reproducción de DVD)
Seleccione el título
37
43
38
31
42
37
MARKER
ZOOM
TOP MENU REPEAT A-B
TOP MENU
REPEAT A-B
Repita la reproducción entre A y B
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
AUDIO/AUDIO SELECT Cambiar el sonido de la VCR
Cambie el idioma de la pista de sonido
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
JUMP
Localización de la escena deseada
ZERO RETURN
ANGLE
Detener la cinta cuando el contador llega a 00:00 25
REW/SEARCH
PLAY
SEARCH/F.FWD
Cambie el ángulo de reproducción
43
25
25
COUNTER RESET Resetear el contador a 00:00
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
CLOCK/COUNTER Cambiar el modo del visualizador frontal
TIMER REC
Ajustar la unidad para que inicie la grabación en ese
SLOW
PAUSE/STILL
mismo momento.
29,30
42
SUB TITLE
ATR
Mostrar subtítulos
SEGUIMIENTO AUTOMÁTICO digital
Seleccione el modo de reproducción
24
PLAY MODE
SPEED
38,39
Ajusta la velocidad de la cinta para grabación 26,28
Cambiar entre TV/AV y DVD 18,27
Reproducción en rebobinado/búsqueda 23,24,36
TV/VCR
REW/SEARCH
PLAY
Reproducción
23,35
F.FWD/SEARCH
Avance rápido/Reproducción en avance/
retroceso rápidos
23,24,36
36
SKIP
/
Salte el capítulo en avance o retroceso
INDEX +/–
STOP
Buscar la marca de ÍNDICE de una cinta
25
Parada
23,35
REC/OTR
SLOW
Grabación
26,28,32
24,36
Avance/retroceso-cámara lenta
Imagen fija/Activar/
PAUSE/STILL
desactivar pausa de grabación
24,27,32,36
10
2C51001AS(06-11)
10
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Control remoto
Coloque las pilas
Abrir la tapa del compartimento
de las pilas siguiendo la
dirección de la flecha.
Coloque dos pilas “AAA”, (no
suministradas) prestando atención
a las marcas de polaridad en el
compartimiento de las pilas.
Recoloque la tapa del
compartimiento.
1
2
3
PRECAUCION CON LAS PILAS
Las precauciones a continuación deben ser cumplidas cuando se utilizan pilas en esta unidad:
1. Utilice solo un tipo especificado de pilas.
2. Cuando coloca las pilas asegúrese de colocarlas con la polaridad correcta, tal como se indica en el
compartimiento de las pilas. Las pilas colocadas invertidas pueden causarle daños a la unidad.
3. No mezcle tipos diferentes de pilas (ej.: pilas alcalinas y carbón zinc), o pilas viejas y nuevas.
4. Si la unidad no va a ser utilizada por un largo período, extraiga las pilas para evitar daños o heridas
resultantes de posibles fugas.
5. No intente recargar las pilas que no sean recargables ya que se pueden recalentar y romperse (Siga las
indicaciones del fabricante de pilas).
Funciones básicas del control remoto
• Presione POWER para encender o apagar el DVD/VCR.
• Presione CH o CH para desplazarse por los canales uno a la vez.
• CH
/
y SET +/– se utilizan también para navegar por el sistema de menús en pantalla.
• Los botones de número permiten acceder directamente a canales concretos.
• Cada vez que se presiona VCR/DVD en el control remoto, la pantalla alterna entre la pantalla VCR (modo
VCR) y la pantalla DVD (modo DVD).
Funcionamiento
• Apunte el mando a distancia al sensor remoto y presione los botones
de control para hacer funcionar.
• Utilice el control remoto dentro de un ángulo de 30˚ hacia ambos
Aproximadamente 15PIES(5m)
lados del sensor remoto, hasta una distancia de unos 5 metros.
11
2C51001AS(06-11)
11
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexiones basicos
Si está utilizando un sistema de antena, siga estos instrucciones. Si está suscrito a televisión por cable (CATV),
pase a la página 14 para las conexiones apropiadas.
CONEXION DE ANTENA A DVD/VCR
El DVD/VCR debe conectarse “entre” la antena y el televisor. Primero, desconecte la antena del televisor y conéctela
al DVD/VCR. Luego, conecte el DVD/VCR al televisor. A continuación se describen 3 métodos comunes para
conectar un sistema de antena a un DVD/VCR. Encuentre el tipo de sistema de antena que esté utilizando y siga el
diagrama de conexiones.
Combinacion de antena de VHF/UHF con cable coaxial de 75 ohmios
DVD/VCR
1
Cable coaxial de 75 ohmios
Combinacion de antena de VHF/UHF con cable de cabeza doble (PLANO) de 300 ohmios
2
3
DVD/VCR
Transformador igualador
entrada de 300 ohmios
salida de 75 ohmios
(no provisto)
Cable de cabeza doble (PLANO) de
300 ohmios
DVD/VCR
Antenas separadas de VHF y UHF
Combinador
entradas de 75/300 ohmios
salida de 75 ohmios
(no provisto)
UHF
VHF
Cable de cabeza doble (PLANO)
de 300 ohmios
Cable coaxial de 75 ohmios
NOTA: Si las antenas de VHF y UHF tienen un cable doble de 300 ohmios (plano), utilice un combinador que
tenga dos entradas de 300 ohmios y una salida de 75 ohmios.
NOTAS: • El DVD/VCR no ofrecerá una imagen clara a menos que la señal de antena sea fuerte. Asegúrese de
conectar correctamente la antena al DVD/VCR.
• Para grabaciones de mejor calidad, le recomendamos usar una antena exterior. No utilice una antena
interior o una antena telescópica.
• Si no está seguro acerca de la conexión, consulte a un técnico de servicio calificado.
12
2C51001AS(12-15)
12
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexiones basicos
CONEXION DEL DVD/VCR A UN TELEVISOR
Una vez que haya conectado la antena al DVD/VCR, usted tendrá que conectar el DVD/VCR al televisor. A
continuación se describen 3 métodos comunes para conectar su DVD/VCR a un televisor. Identifique el tipo de
televisor que esté utilizando y siga el diagrama de conexiones.
Este DVD/VCR dispone de una única salida de 75 ohmios para conexión a un televisor. Si su televisor dispone
de entradas de antena de VHF y UHF separadas (números 2 y 3 a continuación), utilice un divisor para
conectar el DVD/VCR al televisor para recepción de VHF y UHF.
TV
Nota: Si se utiliza una antena VHF
o UHF, ajuste la opcion de
menu TV/CATV al modo “TV”.
Cable coaxial de 75 ohmios (Provisto)
Televisor con entrada única de 75
ohmios para VHF/UHF
TV
Nota: Si se utiliza una antena VHF
o UHF, ajuste la opcion de
Divisor
entrada de 75 ohmios
salidas de 75/300 ohmios
(no provisto)
menu TV/CATV al modo “TV”.
Cable coaxial de 75
ohmios (Provisto)
Televisor con entrada de 300
ohmios para antena de UHF y de
75 ohmios para antena de 300
ohmios
TV
Nota: Si se utiliza una antena VHF
o UHF, ajuste la opcion de
Divisor
menu TV/CATV al modo “TV”.
entrada de 75 ohmios
salidas de 300 ohmios
(no provisto)
Cable coaxial de 75
ohmios (Provisto)
Televisor con entrada de 300
ohmios para antena de UHF y de
300 ohmios para antena de VHF
13
2C51001AS(12-15)
13
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexiones de TV cable (CATV)
Muchas compañías de TV cable ofrecen servicios que permiten recibir canales adicionales, incluyendo
canales pagados o por suscripción. Al tener una gama de sintonización ampliada, este DVD/VCR puede
sintonizar la mayoría de los canales de TV cable sin necesidad de usar un caja convertidora proporcionada por
la compañía de TV cable, salvo aquellos canales que han sido intencionalmente codificados.
Si se suscribe a un canal especial que esté codificado, usted deberá usar una caja decodificadora para poder
recibir dicho canal.
DVD/VCR
1
TV
Cable entrante
PERMITE: Grabar desde canales no codificados.
*
*
*
Usar el temporizador programable.
Grabar desde un canal mientras se ve otro.
DVD/VCR
2
Convertidor/
Decodificador
TV
Cable
entrante
PERMITE: Grabar desde canales a través de la caja
*
convertidora (codificados y no codificados).
NOTA: Para grabar desde el convertidor/
decodificador, el sintonizador del
DVD/VCR deberá ser sintonizado
al canal de salida del convertidor,
normalmente al canal 3 ó 4.
Usar el temporizador programable para grabar sólo
desde el canal seleccionado en la caja convertidora.
NO PERMITE: Grabar desde un canal mientras se ve otro.
*
*
*
Usar el sintonizador del DVD/VCR para seleccionar
canales.
DVD/VCR
3
TV
Convertidor/
Decodificador
Cable entrante
PERMITE: Grabar desde canales no codificados.
*
NOTA: Al reproducir una cinta o usar el
sintonizador incorporado del
Usar el temporizador programable.
Grabar desde un canal no codificado mientras
se ve cualquier canal seleccionado en la caja
convertidora.
*
*
DVD/VCR, el convertidor deberá
ser ajustado a la salida de canal
de video del DVD/VCR (3 ó 4).
NO PERMITE: Grabar desde canales codificados.
NOTA: Siempre que haya una caja convertidora/decodificadora instalada antes que el DVD/VCR, usted debera
sintonizar el DVD/VCR a la salida de la caja convertidora/decodificadora, usualmente al canal 3 ó 4.
14
2C51001AS(12-15)
14
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexiones de TV cable (CATV)
IMPORTANTE: ASEGURESE DE QUE EL DE MENU TV/CATV ESTE AJUSTADO AL MODO “CATV”.
Este DVD/VCR no puede recibir programas codificados debido a que no está equipado con un descodificador.
Para poder recibir programas codificados, usted deberá utilizar un decodificador.
Las cajas decodificadoras pueden adquirirse en las compañías de TV cable. Para detalles acerca de la
conexión a sus equipos decodificadores, consulte a la compañía de TV cable local.
Hay muchas formas de conectar el DVD/VCR a un sistema de cable. A continuación presentamos seis
métodos comunes de conexión.
DVD/VCR
TV
4
Divisor
Interruptor
A/B
Cable
entrante
Convertidor/Decodificador
PERMITE: Grabar desde todos los canales a través de la caja convertidora.
*
*
*
Ver canales codificados mientras se graba desde otro canal.
Usar el temporizador programable para grabar sólo desde el canal seleccionado en la caja convertidora.
NO PERMITE: Grabar desde un canal mientras se ve otro.
*
*
Usar el sintonizador del DVD/VCR para seleccionar canales.
DVD/VCR
5
TV
Divisor
Cable
entrante
Interruptor
A/B
Convertidor/
Decodificador
PERMITE: Grabar desde canales no codificados.
*
Ver canales codificados mientras se graba desde otro canal.
Ver canales especiales a través de la caja convertidora mientras se graba canales no codificados.
Usar el temporizador programable.
*
*
*
NO PERMITE: Grabar desde canales codificados.
DVD/VCR
Convertidor/
Decodificador
6
TV
Divisor
Cable
entrante
Interruptor
A/B
Convertidor/
Decodificador
PERMITE: Grabar desde todos los canales a través de la caja convertidora.
*
*
Grabar desde un canal codificado o no codificado mientras se ve cualquier canal (codificado o
no codificado) seleccionado en la caja convertidora.
Usar el temporizador programable para grabar sólo desde el canal seleccionado en la caja convertidora.
NO PERMITE: Usar el sintonizador del DVD/VCR para seleccionar canales.
*
15
2C51001AS(12-15)
15
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexión para reproducción
La opción que elija para la interconexión de los diversos componentes de video y de audio al DVD/VCR dependerá
del modelo y de las funciones de cada uno de los componentes. Busque en los manuales o guías del usuario
suministrados con cada uno de los componentes la ubicación exacta de las entradas y salidas de video y audio.
Conexión a un TV con salida de audio/video
Puede disfrutar de la reproducción conectando la unidad a un TV.
Conecte la unidad a un TV equipado con tomas de entrada de audio (L/R) y entrada de vídeo a través del
cordón de audio/vídeo incluido.
TV
A SALIDA DE VIDEO
DVD/VCR
A ENTRADA
DE VIDEO
A ENTRADA DE AUDIO (DERECHA)
A ENTRADA DE AUDIO (IZQUIERDA)
A SALIDA DE AUDIO (IZQUIERDA)
A SALIDA DE AUDIO (DERECHA)
Cordón AUDIO/VIDEO (incluido)
Conexión a un TV con salida S-Video (para reproducción de DVD/CD)
Si su TV dispone de una entrada de S-VIDEO, puede obtener una mayor calidad conectándolo a la salida de
S-VIDEO de la unidad a través del cordón S-video, en lugar de conectar la entrada de vídeo del TV a la toma
VIDEO de la unidad.
TV
Cordón S-VIDEO (no incluido)
DVD/VCR
A ENTRADA
DE S-VIDEO
A ENTRADA DE AUDIO (DERECHA)
A SALIDA DE S-VIDEO
A SALIDA DE AUDIO
(IZQUIERDA)
A SALIDA DE AUDIO
(DERECHA)
A ENTRADA DE AUDIO (IZQUIERDA)
Interruptor Selector de
COMPONENT/S-VIDEO
Cordón AUDIO (no incluido)
Conexión a un TV con salida de vídeo de componentes (para reproducción de DVD/CD)
Puede disfrutar de una imagen de alta calidad al conectar las tomas de salida de vídeo de componentes a las
tomas de entrada de vídeo de componentes del TV a través de los cables de vídeo de componentes (no
incluidos).
TV
DVD/VCR
A salida de video
de componentes
A entrada de video de componentes
Cable de VIDEO DE COMPONENTES (no incluido)
NOTAS:
•
Si realiza la conexión a unTV con toma de S-video o tomas de componentes, ajuste el interruptor selector de S-VIDEO/
COMPONENT en la posición deseada.Y también debe seleccionar la entrada de vídeo correspondiente en su TV.
Al conectar a un televisor usando la toma VIDEO o S-VIDEO, verifique que el indicador PROGRESSIVE de la
ventana de visualización no esté encendido. Si está encendido, las salidas VIDEO y S-VIDEO no suministran las
señales correctas y no se puede ver la imagen. Para apagar el indicador PROGRESSIVE, desactive el modo de
exploración progresiva (véase la página 52).
•
• Si las tomas de entrada de vídeo de componentes de su televisor son de tipo BNC, utilice un adaptador para convertir
una clavija de patillas en una clavija BNC (no incluida).
16
2C51001AS(16-19)
16
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexión para reproducción
Conexión a un amplificador estéreo con salida de audio
Puede disfrutar de audio de alta calidad conectando la salida de audio a un amplificador.
Conecte las tomas de SALIDA DE AUDIO a cualquier entrada de línea (como AUX, DVD, CD, etc.) de un
amplificador de audio.
DVD/VCR
Amplificador
estéreo
A ENTRADA DE AUDIO
(DERECHA)
A SALIDA DE AUDIO (IZQUIERDA)
A SALIDA DE AUDIO (DERECHA)
Cordón AUDIO (no incluido)
A ENTRADA DE AUDIO
(IZQUIERDA)
Conexión a un amplificador AV con sonido envolvente digital integrado
Si va a utilizar un amplificador con sonido envolvente digital integrado como se indica a continuación, podrá
disfrutar de las diversas opciones de audio como Dolby Digital y DTS mediante la salida digital óptica o coaxial.
Utilice esta conexión para conectar un:
• Amplificador AV con decodificador *Dolby Digital integrado
• Amplificador AV con decodificador *DTS
Salida de audio digital coaxial
Cordón VIDEO (no incluido)
A ENTRADA DE
VIDEO
DVD/VCR
Conector de Salida VIDEO
TV
NOTA:
Amplificador AV con
Puede realizar la conexión a un TV
mediante un cable de video de
componentes (no incluido) o un cable S-
Video (no incluido) en lugar de mediante
un cable de video (no incluido).
varios decodificadores
integrados como se
indica anteriormente
Cable digital coaxial (no incluido)
Conexión del cable digital óptico
Puede realizar la conexión a un amplificador AV mediante un cable digital óptico (no incluido) en lugar de
mediante un cable digital coaxial.
Al conectar el cable digital óptico (no incluido), quite la protección antipolvo del panel posterior.
Cuando no utilice el cable digital óptico, vuelva a colocar la protección antipolvo.
NOTAS:
•
Las tomas DVD OUTPUT (OPTICAL, COAXIAL, AUDIO L/R, S-VIDEO y COMPONENT) sólo son útiles para la
sección DVD.
En estas conexiones no pueden usarse funciones VCR; tampoco aparecen los menús VCR.
La señal VHS sólo se envía a través de la toma de componentes (DVD/VCR OUTPUT) y UHF/VHF OUT.
• Cuando haga las conexiones que se muestran arriba, no ajuste DOLBY DIGITAL a DOLBY DIGITAL o DTS con
ON en el Amplificador AV. Si lo hace, saldrá repentinamente un ruido fuerte por los altavoces, afectando sus
oídos o dañando los altavoces.
• Precaución a tener en cuenta con el conector de salida de audio digital óptico: No debe conectarse a un
amplificador (con un conector de entrada digital óptica) que no disponga de decodificador Dolby Digital o DTS.
De lo contrario, cualquier intento de reproducción de un DVD puede producir un nivel de ruido tan elevado que
puede resultar perjudicial para los oídos o estropear los altavoces.
• El audio DTS sólo se enviará a través de la salida COAXIAL u ÓPTICA. Para escuchar audio DTS, se requiere
un decodificador DTS.
•
Cuando escuche CD’s con codificación DTS, sólo escuchará ruido de las bocinas o de las salidas stereo análogas.
• Algunos decodificadores DTS que no soportan la interfase DVD-DTS tal vez no funcionen adecuadamente con
la unidad.
17
2C51001AS(16-19)
17
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Ajuste del canal de video/Seleccion de idioma en pantalla
Cuando se conecta el TV sólo con un cable de antena.
AJUSTE DEL CANAL DE VIDEO
Para vizualizar la reproducción de
una cinta grabada, o para ver un
programa seleccionado por el
selector de canal del videograbador,
el televisor deberá estar ajustado al
canal 3 ó 4 (canal de video).
Mantenga presionado 3 ó 4 en el control
1 remote durante 3 segundos en el modo
espera para seleccionar CH 3 ó 4. El
número del canal seleccionado parpadeará en la pantalla
durante 4 segundos.
Encienda el televisor y ajústelo al canal 3 ó 4, en
2 correspondencia con el canal seleccionado en el paso 1.
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
Presione POWER para encender el DVD/VCR.
3
DISPLAY/CALL
1
4
7
2
5
8
3
6
Presione VCR/DVD para seleccionar el modo VCR.
4 El indicador VCR del panel frontal se iluminará.
INPUT SELECT/
PROGRESSIVE
Presione selector TV/VCR para seleccionar la posición VCR.
5 El indicador VCR se iluminará.
9
0
Presione el botón selector de canal en L o M (CHANNEL L/M)
6 para recibir una estación de TV de su área. El número de
CH
canal aparecerá en la pantalla durante unos 4 segundos.
TRACKING/
TRACKING/
SET
SET
–
+
Para un sintonizador de TV de pulsador
SELECT/
ENTER
Si el CH 3 ó 4, correspondiente al canal de video, no puede
sintonizarse en su televisor, proceda como sigue: ajuste el selector
de canal 3/4 del videograbador al canal 3 ó 4, reproduzca una
cinta pregrabada y sintonice el televisor para recibir una clara
imagen en color desde el videograbador. Para mayores detalles,
consulte el manual de instrucciones de su televisor.
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
MARKER
ZOOM
TOP MENU REPEAT A-B
Seleccion de idioma en pantalla
Puede escoger entre tres idiomas diferentes (inglés, francés
y español) para los despliegues en pantalla.
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
SUB TITLE/
ATR
PLAY MODE/
SPEED
Presione VCR MENU.
Aparece la pantalla del menú de la VCR. Presione el botón
SET + o – para seleccionar la option SYSTEM SETUP, luego
presione ENTER.
TIMER REC
TV/VCR
1
REW/SEARCH
PLAY
SEARCH/F.FWD
Si utiliza la unidad por primera
vez y presiona VCR MENU, es
posible que aparezca la pantalla
de menú SYSTEM SETUP del
paso 2 en lugar de la pantalla del
menú principal.
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
SLOW
PAUSE/STILL
NOTAS:
• El canal de vídeo preajustado en
fábrica es CH 3.
Presione SET + o – para
2 seleccionar el modo LANGUAGE,
• Si el aparato no funciona
correctamente, o No se pueden
presionar los botones (en la
unidad y/o control remoto):
La electricidad estática, etc. puede
afectar el funcionamiento del tocadiscos.
Desenchufe el cable eléctrico de CA una
vez y vuelva a enchufar.
luego presione ENTER.
Presione SET + o – para
3
seleccionar el idioma deseada:
•
Tanto el VCR como el DVD tienen sus
propias opciones de menú(ver página 34).
inglés (ENGLISH), español
(ESPAÑOL) o francés
(FRANCAIS), luego presione
ENTER.
• Si no se presiona ningún botón en
más de 60 segundos, la pantalla
MENU volverá automáticamente a su
función normal de TV.
Presione VCR MENU para volver a la imagen normal de TV.
18
4
2C51001AS(16-19)
18
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Ajuste del reloj manual
Se debe haber ajustado la fecha y la
hora para poder hacer grabaciones
con temporizador.
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de vídeo.
• Presione VCR/DVD para seleccionar el modo VCR. (El indicador
VCR se iluminará.)
EJEMPLO: Ajuste del reloj a miércoles, 8:30 AM 27 (SAB)
marzo, 2004.
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
Presione VCR MENU. Aparece la pantalla del menú de la
1 VCR.
2
DISPLAY/CALL
1
4
7
2
5
8
3
6
Presione SET + o – para
seleccionar la option SYSTEM
SETUP, luego presione ENTER.
INPUT SELECT/
PROGRESSIVE
9
0
CH
TRACKING/
TRACKING/
SET
SET
–
+
Presione SET + o – para
SELECT/
ENTER
3 seleccionar la opción CLOCK
SET, luego presione ENTER.
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
MARKER
ZOOM
TOP MENU REPEAT A-B
Presione SET + o – para
4 establecer el mes, y a
AUDIO/
JUMP/
ANGLE/
CLOCK/
MONTH
DAY
3
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
continuación presione ENTER.
1 (SAT)
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
YEAR
TIME
2003
12 : 00AM
⟨+/-/ENTER/CANCEL/MENU⟩
REW/SEARCH
PLAY
SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
Para realizar correcciones en cualquier momento del proceso
Presione CANCEL varias veces hasta que el elemento
deseado parpadee, a continuación presione SET + o –.
SLOW
PAUSE/STILL
Ajuste el día, año y hora de
acuerdo con el procedimiento del
paso 4.
5
6
MONTH
DAY
3
27 (SAT)
2004
YEAR
TIME
8 : 30AM
⟨+/-/ENTER/CANCEL/MENU⟩
NOTA:
Tras un fallo en el suministro de
alimentación o desconexión del
enchufe de alimentación. En este
caso, reajuste la hora actual.
Una vez ajustado el reloj, la fecha
y la hora empiezan a funcionar
automáticamente.
8 : 30AM SAT
19
2C51001AS(16-19)
19
18/11/03, 2:40 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Ajuste del sintonizador
Este DVD/VCR está equipado con una función de memorización de canales que permite avanzar o
retroceder al siguiente canal almacenado en la memoria, pasando por alto los canales no deseados.
Antes de seleccionar canales, éstos deberán ser programados en la memoria del DVD/VCR. Además de
los canales normales de VHF y UHF, este DVD/VCR puede recibir hasta 113 canales de TV cable. Para
usar el DVD/VCR con una antena, ajuste la opcion de MENU al mode TV. Este interruptor viene ajustado
de fábrica a la posición CATV.
Preparación:
• ENCIENDA el TV y ajústelo al modo de entrada de video.
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
•
Presione VCR/DVD para seleccionar el modo VCR. (El
indicador VCR se iluminará.)
DISPLAY/CALL
1
4
7
2
5
8
3
6
INPUT SELECT/
PROGRESSIVE
SELECCION DE TV/CATV
Presione VCR MENU. Aparece la pantalla del menú de la
1 VCR. Presione SET + o – para seleccionar la opción CH
9
0
SETUP, luego presione ENTER.
CH
Presione SET + o – para
TRACKING/
SET
–
TRACKING/
SET
+
2 seleccionar el modo TV/CATV.
CH SETUP
TV CATV
AUTO CH MEMORY
ADD/DELETE
SELECT/
ENTER
+/-/ENTER/MENU
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
Presione ENTER para
seleccionar el modo TV o CATV.
La flecha indica el modo
seleccionado.
MARKER
ZOOM
TOP MENU REPEAT A-B
CH SETUP
TV CATV
AUTO CH MEMORY
ADD/DELETE
3
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
TV - Canales de VHF/UHF
CATV - Canales de TV CABLE
SUB TITLE/
ATR
PLAY MODE/
SPEED
+/-/ENTER/MENU
TIMER REC
TV/VCR
REW/SEARCH
PLAY
SEARCH/F.FWD
Presione VCR MENU dos veces para volver a la imagen
4 normal de TV.
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
Ajuste automático de los canales
SLOW
PAUSE/STILL
Su videograbadora puede recibir un máximo de 181 canales
prorgramándolos en la memoria.
Repita el paso 1 anterior y
CH SETUP
1 presione SET + o – para
TV CATV
seleccionar la opción AUTO CH
MEMORY.
AUTO CH MEMORY
ADD/DELETE
+/-/ENTER/MENU
NOTA:
No se puede seleccionar “CH SETUP”
si se ajusta el canal en “L”.
Luego presione ENTER.
Empieza la sintonización
automática. La indicación de
canal irá subiendo y cuando
termina, la pantalla vuelve a su
estado normal.
2
CH 002
20
2C51001AS(20-25)
20
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Borrado de un canal de la memoria/Eliminacion de buido
Preparación:
BORRADO DE UN CANAL
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
DE LA MEMORIA
•
Presione VCR/DVD para seleccionar el modo VCR. (El
Puede añadir los canales que
desee o borrar los que no desee
manualmente.
indicador VCR se iluminará.)
Repita el paso 1 de la página 20.
OPEN/
CH SETUP
1
2
POWER
EJECT
CLOSE
VCR/DVD
Presione SET + o – hasta que el
indicador “ADD/DELETE” empiece
a parpadear seguidamente, y a
continuación presione ENTER.
TV CATV
AUTO CH MEMORY
ADD/DELETE
DISPLAY/CALL
1
4
7
2
5
8
3
6
INPUT SELECT/
PROGRESSIVE
+/-/ENTER/MENU
9
0
Para añadir o borrar los canales deseados
Presione los botones de
número o SET + o – para
seleccionar un número de
canal que desee añadir o
borrar.
1
CH
ADD
CH 003
TRACKING/
TRACKING/
SET
SET
–
+
SELECT/
ENTER
2
Para añadir canales
Presione ENTER hasta que
aparezca “ADD” en la pantalla
para añadir el canal sin
memorizar.
⟨+/-/0-9/ENTER/MENU⟩
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
MARKER
ZOOM
TOP MENU REPEAT A-B
Para borrar canales
Presione ENTER hasta que aparezca “DELETE” en la
pantalla para borrar el canal de la memoria. El número
del canal parpadeará.
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
3
Repita de
a
para añadir o borrar otro canal.
1
2
REW/SEARCH
PLAY
SEARCH/F.FWD
Presione VCR MENU para volver a la imagen normal de TV.
3
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
ELIMINACION DE RUIDO
SLOW
PAUSE/STILL
Cuando no desea recibirlas señales de transmisión débiles,
Puede hacer que aparezca una pantalla azul negro
seleccionando el FONDO SIN RUIDO “ON” Este aparato sale
de fábrica con el FONDO SIN RUIDO en “ON”.
Repita los pasos 1~2 de la página 19 y presione el botón SET +
o – para seleccionar la opción “NO NOISE BACKGROUND”.
1
Presione ENTER para
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
2 seleccionar la posición ON.
+/-/ENTER/MENU
Presione VCR MENU para volver a la imagen normal de TV.
3
21
2C51001AS(20-25)
21
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Colocación y extracción de videocassettes
Use sólo videocassettes marcados
.
COLOCACION
Presione en el centro del videocassette hasta que
se retraiga automáticamente.
Introduzcaelvideocassetteconelladoquellevalaetiquetahacia
arriba y la lengüeta para evitar el borrado situada a su izquierda.
No se puede introducir un videocassette si está invertido.
VCR
Lengüeta para evitar
el borrado
ENCENDIDO AUTOMATICO
Al introducir un videocassette, el VCR se ENCENDERÁ automáticamente.
REPRODUCCION AUTOMATICA
Cuando se coloca un videocassette desprovisto de su lengüeta para evitar
el borrado, la reproducción comenzará inmediatamente.
EXTRACCION
Presione EJECT del DVD/VCR o cotrol
remoto.
Extraiga el videocassette.
1
2
Expulsión automática de la cinta
Este VCR rebobina automáticamente la cinta cuando llega al final. Y una vez se ha rebobinado la cinta al
principio, el videocassette se expulsa automáticamente.
PARA VOLVER A GRABAR
Cubra el agujero con trozo de cinta adhesiva.
Para evitar el borrado involuntario
Utilice un destornillador para quitar la lengüeta para
evitar el borrado.
destornillador
Lengüeta para evitar
el borrado
Cinta adthesive
VELOCIDAD DE CINTA Y TIEMPO MAXIMO DE GRABACION
CINTA DE VIDEOCASSETTE
VELOCIDAD DE
CINTA
T-160
2-2/3 horas
8 horas
T-120
2 horas
6 horas
T-90
T-60
T-30
SP (Standard Play)
SLP (Super Long Play)
1-1/2 horas
4-1/2 horas
1 hora
3 horas
30 minutos
1-1/2 horas
22
2C51001AS(20-25)
22
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Reproducción de cintas de cassette
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
• Presione VCR/DVD para seleccionar el modo VCR. (El
indicador VCR se iluminará.)
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
Coloque una cinta pregrabada (Cuando
1
se carga una cinta de cassette sin la
DISPLAY/CALL
1
4
7
2
5
8
3
6
lengüeta de prevención de borrado, la
reproducción comenzará
automáticamente).
INPUT SELECT/
PROGRESSIVE
PARA INICIAR LA REPRODUCCION
9
0
2
Presione PLAY. La reproducción
comenzará. “ ” aparecerá en
pantalla durante 4 segundos
aproximadamente.
CH
TRACKING/
SET
–
TRACKING/
SET
+
SELECT/
ENTER
PARA INTERRUMPIR
REPRODUCCION
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
Presione STOP (PARADA) una
vez. La cinta parará, pero
permanecerá cargada y lista
para reproducir.
MARKER
ZOOM
TOP MENU REPEAT A-B
“
” aparecerá en pantalla
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
durante 4 segundos
aproximadamente.
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
PARA REBOBINAR O AVANZAR LA CINTA RAPIDAMENTE
Detenga la reproducción o la grabación mediante STOP.
REW/SEARCH
PLAY
SEARCH/F.FWD
Para rebobinar la cinta:
Para avanzar la cinta
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
Presione REW.
Presione F.FWD.
SLOW
PAUSE/STILL
Paradetenerelbobinadodelacinta, presioneSTOP. Parapasar
directamente a reproducción (sin presionar STOP), presione
PLAY.
NOTAS:
• Este DVD/VCR selecciona
Modo de búsqueda de imagen hacia delante/atrás
Mientras se bobina la cinta, puede pasar al modo de búsqueda
de imagen (ver página siguiente). Para ello, presione REW o
F.FWD y manténgalo presionado. La unidad volverá a bobinar la
cinta en cuanto se suelte el botón.
automáticamente la velocidad de la
cinta de reproducción SP, LP o SLP.
• Se puede reproducir simultáneamente el
videocassette y el disco DVD. Si presiona
VCR/DVD, se alterna en pantalla la
reproducción de la cinta y del DVD.
• Al seleccionar el modo VCR durante la
reproducción de DVD, la reproducción
de DVD se detiene automáticamente
al cabo de unos 5 minutos.
23
2C51001AS(20-25)
23
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Reproduccion especial
Reproducción repetida
Búsqueda de imagen
Función de búsqueda de imagen hacia atrás
Presione REW una o dos veces durante la reproducción.
Toda la cinta de vídeo se reproducirá hasta el final. La
cinta será entonces rebobinada hasta el principio y se
repetirá la reproducción.
Función de búsqueda de imagen hacia delante
Presione F.FWD una o dos veces durante la reproducción.
Para volver a la reproducción: Presione PLAY.
Presione VCR MENU. Presione SET + o – para
seleccionar AUTO REPEAT.
1
TIEMPOS DE BUSQUEDA
VELOCIDAD DE BUSQUEDA
VELOCIDAD DE
A continuación, presione
ENTERparaseleccionar
“ON” u “OFF”.
Si se selecciona “ON”, la
reproducción se repetirá
indefinidamente.
2
PRESIONAR
UNA VEZ
PRESIONAR
DOS VECES
LA CINTA
SP (Reproducción normal)
3 veces la normal 5 veces la normal
LP (Large duración)
7 veces la normal
9 veces la normal
15 veces la normal
SLP (Superlarge duración) 9 veces la normal
IMAGEN FIJA
Presione PAUSE durante la reproducción. Para
continuar la reproducción normal: Presione PLAY.
Presione VCR MENU hasta que se borre la
pantalla de menú.
Si presiona CALL, “ ” aparecerá en pantalla.
3
CAMARA LENTA
Durante la reproducción presione SLOW.
Para volver a la reproducción: Presione PLAY o SLOW.
Para iniciar la reproducción, presione PLAY.
4
La reproducción se repetirá indefinidamente.
AJUSTE DEL SEGUIMIENTO Y AJUSTE VERTICAL
EN CAMARA LENTA
Si aparecen franjas de interferencia en la imagen,
presione los botones TRACKING + o – para reducir
la interferencia. Si la imagen fija oscila demasiado,
presione los botones TRACKING + o –.
Para cancelar el modo de repetición:
Siga los pasos 1, luego presione ENTER para
seleccionar la posición OFF. Presione VCR MENU
para retornar a TV.
AVANCE CUADRO A CUADRO
Presione PAUSE durante la reproducción.
Presione SLOW repetidamente: La imagen avanza
cuadro a cuadro
Paravolveralareproducción:PresionePLAYoPAUSE.
Ajuste de la condición de seguimiento
Ajuste de seguimiento automático
Alintroducirunacintaeiniciarlareproducción, sepone
en funcionamiento el seguimiento automático que
analizacontinuamentelaseñalparaofrecerunacalidad
de imagen óptima durante la reproducción.
Ajuste de seguimiento manual
Si el seguimiento automático no logra eliminar
correctamente las interferencias durante la
reproducción,presioneTRACKING+/–paraeliminarlas
manualmente.
Aparecerá “MANUAL TR.”. Presione brevemente para
unajusteligero, omantengapresionadoparaunajuste
más marcado.
• Presione ATR para volver a activar el seguimiento
automático.
Aparecerá “AUTO TR.”.
NOTAS:
•
La salida de audio es silenciada durante LA
BUSQUEDA A VELOCIDAD, CAMARA LENTA,
AVANCE CUADRO A CUADRO, y IMAGTEN FIJA.
• Durante el modo de búsqueda de imagen aparecerán
franjas de interferencia provocadas por el sistema.
• La reproducción especial cambiará automáticamente
a reproducción transcurridos unos 5 minutos para
protegerlacintadevideocontraundesgasteexcesivo.
24
2C51001AS(20-25)
24
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Función VUELTA A CERO / Sistema de búsqueda de índices
de vídeo
Preparación:
Función VUELTA A CERO
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
Esta función hace que el rebobinado de
•
Presione VCR/DVD para seleccionar el modo VCR. (El
la cinta se detenga automáticamente
cuando el contador llega a la posición
00:00:00.
indicador VCR se iluminará.)
DISPLAY/CALL
1
4
7
2
5
8
3
Presione CALL.
El visualizador del contador muestra el
tiempo de ejecución de la cinta durante
la reproducción o grabación.
1
2
8 : 47AM MON
HI-FI
INPUT SELECT/
PROGRESSIVE
6
VCR
00 : 04 : 38 SP
9
0
CH
Presione COUNTER RESET en la
posición deseada de la cinta. El
visualizador del contador se reseteará
a la posición “00:00:00” (por ejemplo,
TRACKING/
TRACKING/
8 : 47AM MON
HI-FI
SET
SET
–
+
SELECT/
ENTER
el principio de la
00 : 00 : 00 SP
VCR
grabación).
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
Presione STOP cuando finalice la reproducción o grabación.
Presione ZERO RETURN.
La cinta se rebobinará o avanzará rápidamente y se detendrá
3
MARKER
ZOOM
TOP MENU REPEAT A-B
automáticamente en la posición “00:00:00”.
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
Botón CLOCK/COUNTER
VCR
Presione CLOCK/COUNTER. El reloj y el
contador de cinta se alternan en el visualizador.
REW/SEARCH
PLAY
SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
VCR
SLOW
PAUSE/STILL
NOTA para el visualizador del contador:
• Si usted rebobina la cinta más allá
de “00:00:00” un signo menos (“-”)
Sistema de búsqueda de índices de vídeo
Esta función permite localizar el inicio de cualquier grabación
realizada en el VCR.
será visualizado frente a la hora.
• Cuando una cinta es cargada, el
contador cambiará a “00:00:00”.
• El contador no funciona en secciones
no grabadas (en blanco) de la cinta.
Al rebobinar la cinta, o en el avance
rápido o reproducción de una cinta
en las secciones en blanco, el
contador parará.
Grabación de una MARCA DE ÍNDICE
La función Búsqueda de índices graba
CH 001
automáticamente una marca de ÍNDICE en
la cinta cada vez que se inicia una
grabación.
INDEX
NOTA para el sistema de búsqueda de
índices de vídeo:
• Es posible que no se encuentre una
marca de ÍNDICE si se grabó al
principio de la cinta.
• Durante la búsqueda de ÍNDICES, es
posible que la cinta se detenga y se
inicielareproducciónenunaubicación
ligeramente diferente.
• La función de ÍNDICES puede no
funcionar correctamente con cintas
de vídeo viejas o gastadas.
• Es posible que no se encuentre las
marcas de ÍNDICE si ésta se
encuentra muy cerca del punto en el
que se inicia la búsqueda.
Búsqueda de índices
Presione INDEX
o
durante el modo de
+3
parada o de reproducción.
Para programas posteriores: Presione INDEX
Para programas anteriores: Presione INDEX
(Al presionar sucesivamente, se aumenta el
número de ÍNDICE hasta 9.)
Cuando se presiona INDEX
unidad inicia la búsqueda del número de
ÍNDICE seleccionado y, una vez encontrado,
se inicia la reproducción automáticamente.
Para detener la búsqueda de índices,
presione STOP.
.
.
o
, la
Se muestra
o
Número de ÍNDICE
(hasta 9)
• Durante la grabación, si se detiene
temporalmentelagrabación,lamarca
de ÍNDICE no se graba en la cinta.
25
2C51001AS(20-25)
25
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Grabacion de un programa de TV
Grabacion y visualizacion
simultanea del mismo
programa
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
•
Presione VCR/DVD para seleccionar el modo VCR. (El
indicador VCR se iluminará.)
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
Coloque un cassette en el cual la
1
DISPLAY/CALL
lengüeta de protección contra borrados
accidentales esté intacta. El DVD/VCR
se encenderá automáticamente.
1
4
7
2
5
8
3
6
INPUT SELECT/
PROGRESSIVE
9
0
Presione selector SPEED para
2 seleccionar la velocidad de cinta
CH
deseada SP o SLP.
TRACKING/
SET
–
TRACKING/
SET
+
El contador y SP o SLP se aparecerá
en la pantalla durante 4 segundos
aproximadamente.
00 : 00 : 00 SP
SELECT/
ENTER
Ajuste la opción TV/CATV en la posición apropiada (ver
página 20).
3
CH
TV - Canales de VHF/UHF
CATV - Canales de TV CABLE
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
MARKER
ZOOM
TOP MENU REPEAT A-B
Presione los botones de selección directa de canal para
4 seleccionar el canal o CH
/
a grabar:
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
1-9
Presione 0 dos veces y luego 1 al 9 como se requiera.
Ej.:para seleccionar 2, presione “002”.
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
10-12
13-99
Presione primero el 0 y luego los 2 dígitos restantes en el
orden de izquierda a derecha. Ej.: presione 012 para “12”.
Presione 2 dígitos en orden.
REW/SEARCH
PLAY
SEARCH/F.FWD
Ej.: presione 22 para “22”.
CH 110
100-125 Presione 3 dígitos en orden.
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
Ej.: Presione 110 para “110”.
SLOW
PAUSE/STILL
VHF/UHF/CATV CANALS
TV
CATV
VHF
2-13
VHF
2-13
UHF
14-69
STD/HRC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100)(125)
01 (5A)
NOTAS:
• Si se quita la lengüeta para evitar el
borrado, se expulsará la cinta al
presionar REC/OTR para grabar.
• Si desea ver la reproducción de DVD
durante la grabación normal en VCR,
presione VCR/DVD para cambiar al
modo DVD y ejecutar la reproducción
de DVD (ver página 35).
Presione el botón REC/OTR.
5 “
CH 110
” aparecerá en la pantalla durante 4
segundos aproximadamente. El
indicador REC aparecerá en pantalla.
• No es posible grabar material de disco
en DVD, CD de audio, etc. en un
videocassette con este DVD/VCR.
INDEX
26
2C51001AS(26-31)
26
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Grabacion de un programa de TV
PARA DETENER LA GRABACION
Presione de parada STOP para detener la
grabacion.
“
” aparecerá en pantalla durante 4
segundos aproximadamente.
OPEN/
PARA DETENER TEMPORALMENTE LA
GRABACION
Presione PAUSE/STILL para evitar grabar
POWER
EJECT
CLOSE
VCR/DVD
DISPLAY/CALL
1
4
7
2
5
8
3
6
material no deseado.
INPUT SELECT/
PROGRESSIVE
“
” aparecerá en pantalla durante 4
segundos aproximadamente. Presione
nuevamente o presione REC/OTR para
continuar la grabación.
9
0
CH
NOTAS:
•
La función pausa será desactivada después de 5 minutos para
prevenir daños a la cinta o el VCR. El VCR cambiará al modo STOP.
TRACKING/
SET
–
TRACKING/
SET
+
• En el modo de pausa de grabación se puede seleccionar un canal
para grabar.
SELECT/
ENTER
PARA GRABAR UN PROGRAMA MIENTRAS SE VE OTRO
Mientras el VCR está grabando, presione el botón selector TV/
VCR para seleccionar la posición TV.
El indicador TV/VCR se apagará y la grabación continuará.
Seleccione el canal de TV que desea mirar usando el selector de
canal del TV.
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
MARKER
ZOOM
TOP MENU REPEAT A-B
NOTA:
AUDIO/
JUMP/
ANGLE/
CLOCK/
Algunos sistemas de conexión TV Cable no permiten ver un canal
mientras se está grabando otro. Ver páginas 14, 15.
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
Para mostrar el estado de funcionamiento de VCR
Presione CALL. Se mostrará la información de reloj, día de la
REW/SEARCH
PLAY
SEARCH/F.FWD
semana y otros datos.
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
MIENTRAS MIRA EL TV
DIA DE LA
SLOW
PAUSE/STILL
RELOJ
8 : 47AM MON
STEREO SAP
CH 125
CANAL
PROGRAMA DE
AUDIO
00 : 00 : 00 SP
VELOCIDAD DE
CINTA
CONTADOR DE TIEMPO REAL
MIENTRAS OPERA UNA CINTA
FUNCION DE REBOBlNADO
AUTOMATICO:
MODO DE
FUNCIONMIENTO
ESTEREO HI-FI
Este VCR rebobinará automáticamente
la cinta cuando ésta ha finalizado
(excepto durante las funciones OTR,
TIMER REC). Este eyectará la cinta.
AUTOMÁTICO DE
REPETICIÓN
HAY CINTA
Para cancelar las pantallas: Presione CALL hasta que
desaparezcan todas las indicaciones.
27
2C51001AS(26-31)
27
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Grebacion por temporizador de un solo toque (OTR)
La prestación de grabación por
temporizador de un solo toque
proporciona una forma simple y
conveniente de efectuar una
grabación con temporizador.
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
•
Presione VCR/DVD para seleccionar el modo VCR. (El
indicador VCR se iluminará.)
EJEMPLO: Una grabación por temporizador de un solo toque para
30 minutos.
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
Coloque un cassette con la lengüeta de
1
DISPLAY/CALL
1
4
7
2
5
8
3
6
protección contra borrados accidentales
esté intacta. El DVD/VCR se encenderá
INPUT SELECT/
PROGRESSIVE
automáticamente.
9
0
Presione SPEED para seleccionar la
2
CH
velocidad de la cinta deseada SP o SLP.
El contador y SP o SLP aparecerán en
TRACKING/
SET
–
TRACKING/
SET
+
pantalla durante 4 segundos
aproximadamente.
00 : 00 : 00 SP
SELECT/
ENTER
Ajuste la opción TV/CATV en la posición apropiada (ver
3
CH
página 20).
TV - Canales de VHF/UHF
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
CATV - Canales de TV CABLE
MARKER
ZOOM
TOP MENU REPEAT A-B
Presione el botones de selección de
4 canales directos o botón CH
CH 110
/
para
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
seleccionar el canal a ser grabado.
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
REW/SEARCH
PLAY
SEARCH/F.FWD
Presione REC/OTR para comenzar la grabación. Presione el
botón nuevamente para detener la grabación después de 30
minutos. Cada presión de REC/OTR aumentará el tiempo de
grabación tal como se muestra en el cuadro a continuación,
hasta un máximo de 6 horas. OTR y el tiempo de grabación
aparecerá en pantalla durante 4 segundos. Y REC seguirá
parpadeando en el visualizador.
5
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
SLOW
PAUSE/STILL
Presione Tiempo de Grabac. Presione Tiempo de Grabac.
Una Vez
2 Veces
3 Veces
4 Veces
5 Veces
GRABAC. NORMAL 6 Veces
3:00
4:00
5:00
6:00
0:30
1:00
1:30
2:00
7 Veces
8 Veces
9 Veces
10 Veces GRABAC. NORMAL
NOTA:
Si desea ver la reproducción de DVD
durante la grabación OTR, presione
VCR/DVD para cambiar al modo DVD y
ejecutar la reproducción de DVD (ver
página 35).
Para cancelar OTR
Presione STOP (PARADA) para apagar la
energía.
“ ꢀ ” aparecerá en pantalla durante 4
segundos aproximadamente.
28
2C51001AS(26-31)
28
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Grabacion por temporizador
La grabacion con temporizador puede ser
programada en la pantalla del TV con el
control remoto.
El temporizador incorporado le permite
grabar automáticamente sin prestar
atención hasta 8 programas durante 1 mes.
Preparación:
• Presione VCR/DVD para seleccionar el modo VCR.
• Presione CALL que tanto la hora como la fecha son correctas
(ver página 27).
EJEMPLO: Programe una grabación con temporizador para el día
26, canal 125 (CATV), 11:00 - 11:30 hrs. PM en el programa de
temporización número 1 (VELOCIDAD DE CINTA: SLP).
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
Presione VCR MENU.
Seleccione la opción TIMER REC
SET y presione ENTER.
MENU
1
TIMER REC SET
AUTO REPEAT
SAP
ON OFF
ON OFF
DISPLAY/CALL
CH SETUP
SYSTEM SETUP
1
2
3
INPUT SELECT/
PROGRESSIVE
+/-/ENTER/MENU
4
5
6
Presione SET + o – para seleccionar el
2 N° de programa, luego presione
TRACKING/
SET
–
TRACKING/
SET
+
ENTER.
SELECT/
ENTER
CH
Presione SET + o – para seleccionar
3 la fecha deseada, luego presione
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
ENTER.
MARKER
ZOOM
TOP MENU REPEAT A-B
Ajuste el tiempo de partida, tiempo de
4 término, canal y velocidad de cinta
AUDIO/
JUMP /
ANGLE/
CLOCK/
como en paso 3.
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
NOTAS:
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
• Presione CANCEL para mover el cursol
hacia atrás para hacer una corrección.
• Para grabar de una fuente externa,
ajuste el canal a “L”. “L” aparecerá al lado
del canal 125 (o 69).
NOTAS:
• Si el símbolo de reloj ( ) parpadea al
finalizar la grabación por temporizador,
el programa de TV no se ha grabado en
su totalidad debido a falta de cinta
suficiente. Presione TIMER REC para
cancelarelprogramadeltemporizadoro
presione EJECT para extraer el
videocassette.
Para fijar otros programas, repita los
5
pasos 2 al 4 para fija el otro programas.
• Para volver a la pantalla normal,
presione dos veces VCR MENU.
• Durante el modo de espera de la
grabación por temporizador, no puede
seleccionarseelmodoVCR.Parautilizar
el VCR, presione TIMER REC primero,
a continuación presione VCR/DVD para
cambiar a modo VCR. Después de usar
el VCR, presione TIMER REC de nuevo
paradejarelVCRenmododeesperade
grabación por temporizador.
• Si presiona TIMER REC durante la
grabaciónportemporizador,lagrabación
seinterrumpirá.SipresionaTIMERREC
denuevodentrodeltiempoprogramado,
la grabación se reanudará.
• Tras un fallo en el suministro eléctrico o
la desconexión de la toma de
alimentación, todos los ajustes de
grabaciones programadas, así como la
visualización de la hora, se perderán al
reanudarse el suministro eléctrico. En
tal caso, resetee el reloj (ver página 19)
y vuelva a programar las grabaciones
por temporizador.
Presione TIMER REC. El símbolo de reloj ( ) aparecerá en
6 el visualizador y el VCR quedará en modo de espera para
grabación. Al mismo tiempo, el modo VCR cambiará
automáticamente a modo DVD. Es posible utilizar el DVD
incluso cuando el VCR está en modo de grabación por
temporizador. Si no utiliza el DVD, apáguelo.
La grabación por temporizador se iniciará 20 segundos antes
de la hora predeterminada.
NOTAS:
• Si el símbolo de reloj ( ) no aparece en el visualizador a pesar
de presionar TIMER REC, es posible que todavía no se haya
cargado el videocassette (ver página 22).
• Si se expulsa el videocassette a pesar de haber presionado
TIMER REC, es posible que se haya quitado la lengüeta de
protección de borrado (ver página 22).
29
2C51001AS(26-31)
29
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Grabacion por temporizador
Caso especial de grabación por temporizador
Confirmación / Cancelación de la grabación
por temporizador
Semanal (ej.: WKL-TU: cada martes (Tuesday) o
diaria (ej.: MO-SA: grabación por temporizador de
lunes (Monday) a sábado (Saturday)
Si se ha activado el temporizador, presione TIMER
1
REC para desactivar el temporizador. El símbolo
dereloj( )desaparecerá.Acontinuación,presione
VCR/DVD para cambiar al modo VCR.
Siga el procedimiento de grabación por temporizador
de la página anterior. En la imagen 3 presione SET + o
– varias veces hasta que aparezca el ajuste deseado.
A continuación, presione ENTER.
PARA CONFIRMAR EL AJUSTE:
2
Al presionar SET – varias veces, el indicador de DATE
cambiarádelasiguienteforma, encasodequehoysea
viernes (Friday).
En la imagen 1 de la página
anteriorseleccionelaopción
TIMERRECSETypresione
ENTER.
A continuación aparecerá
en pantalla la lista de
programasdeltemporizador
como se muestra a la
derecha.
El día de hoy (Viernes)
SU-SA (Domingo to Sabádo)
MO-SA (lunes to Sabádo)
MO-FR (Lunes to Viernes)
WKL-TH (Semanal Jueves)
Un mes después
menos undía
PARA CANCELAR UN PROGRAMA
3
WKL-WE
Presione SET + o – para
seleccionar el programa
que no necesita más y
presione CANCEL para
cancelar un programa.
(Semanal Miércoles)
Presione VCR MENU varias veces hasta que
aparezca la imagen de TV.
4
Superposicióndeprogramasdetemporizador
• No superponga programas distintos, dado que se
perderán las partes conflictivas de los mismos. La
primera hora de programación tendrá prioridad
sobre la siguiente hora de programación, tal y
como se muestra en el diagrama.
NOTAS:
• Si quedan otros programas de grabación por
temporizador, debe presionarse TIMER REC para
volver a activar el temporizador. De lo contrario, se
pasarán por alto los programas de grabación por
temporizador restantes.
• Noesposibleconfirmarelprogramaportemporizador
durante la grabación por temporizador.
• Puede corregir el ajuste programado en el modo de
confirmación de programa.
8 : 00
9 : 00
10 : 00
11 : 00
Programa 1
Programa 2
Partes borradas
Programa 3
En el paso 2 anterior, presione ENTER para acceder
al modo de entrada del programa. A continuación,
presione ENTER varias veces hasta que parpadee el
elementoquedeseacorregir.
Sección no grabada
Prog.1
Prog.2
Prog.3
Ajuste del
control de
grabación
DATE
START END
CH
26(SU) 1–1::0–0–PM 1–1::3–0–PM125 SLP
Corrija entonces los datos
con SET + o –. Finalmente,
presione VCR MENUvarias
veces hasta que aparezca
la imagen del TV.
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – –
– – –
– – –
– – –
– – –
– – –
– – –
–
–
–
–
–
–
–
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
NOTAS:
• La grabación cada día/semana podrá efectuarse de
manera continua hasta que se cancele o se
alcance el final de la cinta.
+/–/ENTER/CANCEL/MENU
• Durante la grabación con temporizador, el
mecanismo de rebobinado automático no funciona.
30
2C51001AS(26-31)
30
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Grabacion y reproduccion estereofonicas/
Segundo programa de sonido
Cuando se recibe una transmisión MTS
STEREO, aparecerá la palabra STEREO
en la pantalla y el programa puede verse
o grabarse en estéreo (consulte las
páginas 28 y 29 para los procedimientos
de grabación). El procedimiento de
grabación Hi-Fi STEREO es el mismo
que para las grabaciones normales.
Grabacion y reproduccion
estereofonicas
STEREO
El sistema de audio de alta fidelidad
VHS permite hacer grabaciones de alta
fidelidad de emisoras MTS STEREO TV.
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
NOTA:
DISPLAY/CALL
1
4
7
2
5
8
3
6
Cuando utilice un sistema CATV, los programas de TV en estero
pueden transmitirse a un canal de cable monoaural. En este caso,
el indicador STEREO no aparecerá y el sonido se escuchará en
monoaural.
INPUT SELECT/
PROGRESSIVE
SELECCION DE SALIDA
9
0
Cuando vea un programa MTS STEREO TV o se reproduzca una
videocinta VHS HI-FI STEREO pregrabada, presione AUDIO SELECT
para seleccionar el audio a escuchar por ambos altavoces. Normalmente
deje en la posición HI-FI STEREO, este botón puede moverse a la
posición MONO si la transmisión en estéreo o el audio de la videocinta
es de mala calidad. Las posiciones “R” y “L” permiten escuchar el audio
del canal HI-FI derecho o izquierdo en ambos altavoces del televisor.
Este botón no tiene influencia cuando ve una videocinta o programa de
TV MONO. Cada vez que oprime este botón, aparece la indicación
OUTPUT SELECTION en la pantalla durante varios segundos. Consulte
el siguiente cuadro.
CH
TRACKING/
SET
–
TRACKING/
SET
+
SELECT/
ENTER
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
SELECCION EL SONIDO SE ESCUCHA
DE SALIDA
ESTEREO
CANAL IZQ
POR AMBOS ALTAVOCES
ESTEREO
CANAL DE AUDIO IZQUIERDO
MARKER
ZOOM
TOP MENU REPEAT A-B
CANAL DER CANAL DE AUDIO DERECHO
MONO
MONO
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
Segundo programa de sonido
Su videograbador tiene un sistema de emisiones SAP que
permite que escuche un segundo programa de sonido
mientras ve un canal seleccionado.
REW/SEARCH
PLAY
SEARCH/F.FWD
Esta función sirve sólo para programas transmitidos en
múltiples idiomas mediante el sistema de transmisión SAP.
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
Presione VCR MENU. Presione SET + o – para seleccionar el
SLOW
PAUSE/STILL
1 modo SAP.
Presione ENTER para seleccionar
2 la posición ON.
A continuación, presione VCR
MENU hasta que se borre la
pantalla de menú.
PARA ESCUCHAR EN SAP (Segundo programa de
sonido)
Cuando el aparato de TV está encendido o se hace una selección
de canal, asegúrese de que aparece aparecen las letras SAP en
la pantalla. Esto significa que se puede recibir transmisiones en.
“Segundo programa de sonido”.
NOTAS:
• Cuando se reproduce una cinta no
grabada en el modo estéreo Hi-Fi, el
audio se conmutará
automáticamente a monoaural.
• Cuando escuche una videocinta
VHS Hi-Fi o una transmisión MTS
por la toma VHF/UHF (sin conectar
el cable de audio/video), el sonido
se escuchará en monoaural.
STEREO SAP
SAP
ó
31
2C51001AS(26-31)
31
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Duplicacion de una cinta de video
DUPLICACION DE UNA CINTA DE VIDEO
Si usted conecta el VCR a otro VCR o cámara de video, usted puede duplicar una cinta previamente
grabada. Haga todas las conexiones antes de encender la unidad.
Coloque una cinta de cassette en blanco con las
Presione REC/OTR en el grabador del VCR,
luego presione PAUSE/STILL.
1 lengüetas de prevención de borrado intactas
4
5
6
dentro del grabador de VCR.
Coloque una cinta de previamente grabada dentro
del reproductor de VCR o una CAMARA DE VIDEO.
Presione el botón PLAY de reproducción en el
VCR o CAMCORDER, luego presione PAUSE/
STILL.
Presione SPEED para seleccionar la velocidad de
2 cinta deseada, SP o SLP.
Se recomienda que fije la VELOCIDAD DE LA
CINTA al modo SP en la grabación de VCR para
obtener mejores resultados.
Suelte el botón grabación pausa y PAUSE/STILL
simultáneamente para comenzar la
duplicación.
Presione de INPUT SELECT para seleccionar
posición de entrada de AUDIO/
VIDEO. La indicación de “L”
3
encenderá.
Conexión a una cámara de video
Conexión a un segundo reproductor de VCR
REPRODUCTOR DE LA
CAMARA DE VIDEO
REPRODUCTOR DE VCR
A conector
para AV
A SALIDA DE AUDIO
(DERECHA)
A SALIDA DE VIDEO
GRABADORA VCR
A SALIDA DE AUDIO
(IZQUIERDA)
Cordón AUDIO/VIDEO (incluido)
GRABADORA VCR
A ENTRADA DE AUDIO (DERECHA)
A ENTRADA DE AUDIO (IZQUIERDA)
Cordón AUDIO/VIDEO (no incluido)
A ENTRADA
DE VIDEO
A ENTRADA
DE VIDEO
A ENTRADA DE AUDIO (DERECHA)
A ENTRADA DE AUDIO (IZQUIERDA)
Para duplicación de una cinta previamente
grabada desde una cámara de video, siga las
instrucciones del fabricante. Abajo se muestra un
sistema tipico de conexión de duplicación de
cámara de video.
32
2C51001AS(32-33)
32
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Disco
Este aparato sólo funciona con discos DVD de la región 1.
El disco cargado (DVD, CD de audio y CD MP3) se reconocerá automáticamente.
Los formatos de disco apropiados son: DVD, CD-R y CD-RW.
Algunos discos CD-R/RW pueden ser incompatibles.
No reproduzca un DVD-ROM, DVD-Audio, CDV, Video-CD, CD-G, Video CD o Foto CD para evitar el borrado
accidental del material pregrabado.
Esta unidad no puede grabar material de disco de DVD, CD de audio, etc. en una cinta de vídeo.
Si presiona REC/OTR durante la reproducción de DVD, aparece en pantalla el símbolo "
" durante unos 4
segundos.
DISCO DVD
Título
TITULO1
CAPITULO 1
TITULO2
CAPITULO 2
Cuando hay dos o más películas grabados en un
disco, el disco se divide en dos o más secciones.
Cada sección se denomina un “TITULO”.
CAPITULO 2 CAPITULO 1
CAPITULO 3
Capítulo
Los títulos pueden subdividirse en muchas secciones.
Cada sección se denomina un “CAPITULO”.
Canción
Un disco compacto de audio puede contener varios elementos.
Estos se asignan a las canciones.
CD
CANCION
1
CANCION
2
CANCION
3
CANCION
4
CANCION
5
Para sacar el disco de su caja
Sujete firmemente por el borde del disco. No toque la superficie del disco.
Saque suavemente el disco de la caja.
• No raye el disco.
• No ensucie la superficie del disco.
• No pegue una etiqueta o cinta adhesiva en el disco.
• No deje caer o doble el disco.
Para guardar el disco
• Guarde el disco en su caja para evitar el riesgo de ralladuras, polvo o daños.
• No deje el disco expuesto a los rayos del sol o en lugares calientes o húmedos.
Para limpiar el disco
Frote el disco con un paño limpio, seco, desde el centro a los bordes.
• No frote el disco con un movimiento circular.
• No utilice limpiadores líquidos o en aerosol.
33
2C51001AS(32-33)
33
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Ajuste de la selección de idioma
Permite seleccionar el idioma.
Preparación:
ENCIENDA el TV y ajústelo en el modo de entrada de video.
Cuando utilice un amplificador, conecte el amplificador.
•
•
Presione VCR/DVD para
No Disc
1
seleccionar el modo DVD.
“Reading” cambia a “No Disc”.
(El indicador DVD se iluminará)
“No Disc” aparecerá en
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
DISPLAY/CALL
1
2
3
6
pantalla. (Si el disco DVD ya
fue introducido, empezará
a
INPUT SELECT/
PROGRESSIVE
correrlo inmediatamente.)
4
7
5
8
Presione SETUP en el modo de
parada. El MENÚ DE AJUSTE
de DVD aparecerá en pantalla.
Language Picture Sound Parental Other
2
3
4
9
0
CH
Presione
other.
para seleccionar
TRACKING/
SET
–
TRACKING/
SET
+
/Enter/Setup/Return
SELECT/
ENTER
Presione
o ENTER para
Language Picture Sound Parental Other
OSD Language English
CH
seleccionar OSD Language.
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
MARKER
ZOOM
TOP MENU REPEAT A-B
/Enter/Setup/Return
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
SUB TITLE/
ATR
PLAY MODE/
SPEED
Language Picture Sound Parental Other
TIMER REC
TV/VCR
Presione
presione
o ENTER y
para
OSD Language English
English
Francais
Espanol
o
REW/SEARCH
PLAY
SEARCH/F.FWD
seleccionar el idioma deseado
(porejemplo ESPAÑOL) y
presione ENTER.
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
/Enter/Setup/Return
SLOW
PAUSE/STILL
NOTA: Para que desaparezca la pantalla SETUP, presione
SETUP (o RETURN).
Si el aparato no funciona
correctamente:
La electricidad estática, etc. puedeafectar
el funcionamiento deltocadiscos.
Desenchufe el cableeléctrico de CA una
vez y vuelva aenchufar.
34
2C51001AS(34-37)
34
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Procedimiento de reproducción
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
•
Presione VCR/DVD para seleccionar el modo DVD. (El
indicador DVD se iluminará.)
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
DISPLAY/CALL
1
2
3
6
Presione OPEN/CLOSE en el
aparato.
Se abrirá la bandeja del disco.
1
INPUT SELECT/
PROGRESSIVE
4
7
5
8
Coloque un disco en la bandeja.
2 Sujete el disco, colóquelo con el
9
0
lado de etiqueta impresa hacia
arriba, alinee en las guía y
coloque el disco en su posición
correcta.
CH
TRACKING/
SET
TRACKING/
SET
–
+
Presione PLAY u OPEN/
SELECT/
ENTER
3 CLOSE en el aparato.
La bandeja del disco se cierra
automáticamente.
En la pantalla del TV la indicación
CH
“
” cambia a “Reading” y
empieza la reproducción.
SETUP/
CLEAR/
DVD MENU
VCR MENU
CANCEL
RETURN
MARKER
ZOOM
TOP MENU REPEAT A-B
• Aparece la pantalla del menú
en la pantalla deTV, si el disco
tiene una función de menú.
Reading
AUDIO/
JUMP/
ANGLE/
CLOCK/
En este caso, presione
o ENTER para activar
una función de menú.
,
,
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
,
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
Presione STOP para terminar la reproducción.
• El aparato graba el punto de parada, según el disco. Aparece
REW/SEARCH
PLAY
SEARCH/F.FWD
4
5
“
“
” en la pantalla.
” sigue parpadeando en el visualizador hasta que se
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
detenga por completo la reproducción. Presione PLAY para
continuar reproduciendo (desde el mismo punto).
• Si presiona nuevamente STOP o se retira el disco (Aparece
SLOW
PAUSE/STILL
“
” en la pantalla), el aparato borrará el punto de parada.
A continuación, presione OPEN/CLOSE.
Se abrireá la bandeja del disco.
Extraiga el disco y presione POWER.
La bandeja se cierra automáticamente y el DVD/VCR se
apaga.
NOTAS:
• Si se coloca un disco no compatible, aparecerá “Incorrect Disc”, “Region Code Error” o “Parentol Error” en la
pantalla de TV dependiendo del tipo de disco cargado. En este caso, revisar el disco nuevamente (Ver
páginas 33 y 44).
• Algunos discos pueden demorar un minuto antes de empezar la reproducción.
• Puede aparecer un símbolo de “Prohibido” en la parte superior izquierda de la pantalla. El símbolo indica que
la función seleccionada no está disponible en el disco o que el DVD/VCR no puede acceder a esa función en
ese momento. No indica un problema con el DVD/VCR.
• Cuando coloque un disco de una sola cara con esa etiquetq abajo (i.e. del lado incorrecto) y presione PLAY o OPEN/
CLOSE en el aparato, “Reading”aparecerá y permanecerá en pantalla durante unos 40 segundos y, a continuación,
cambiará a “Incorrect Disc”.
• Algunas funciones de reproducción de DVD pueden haber sido elegidas por el productor de la película. Como este
aparato reproduce los DVD de acuerdo con las posibilidades introducidas por el productor, algunas funciones de
reproducción pueden no existir. Consulte además las instrucciones que vienen con el DVD.
• Cuando toque CD’s de audio codificados DTS, se escuchará ruido excesivo de las salidas análogas stereo. Para
evitar posibles daños al sistema de audio, el consumidor debe tomar las debidas precauciones cuando las salidas35
análogas stereo del aparato DVD estén conectadas a un sistema de amplificación.
2C51001AS(34-37)
35
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Reproducción especial
Nota: Puede ocurrir una leve demora
entre el momento en que presiona el
botón y que se active la función.
Reproducción con avance rápido
Presione F.FWD durante la reproducción normal.
Cada vez que presione F.FWD, aumentará la velocidad de la
búsqueda
(x2),
(x4),
(x8),
(x20).
• Para seguir con la reproducción normal, presione PLAY.
OPEN/
POWER
EJECT
CLOSE
VCR/DVD
DISPLAY/CALL
1
2
3
6
Reproducción con retroceso rápido
Presione REW durante la reproducción normal.
Cada vez que presione REW, aumentará la velocidad de la
INPUT SELECT/
PROGRESSIVE
4
7
5
8
búsqueda
(x2),
(x4),
(x8),
(x20).
9
0
• Para seguir con la reproducción normal, presione PLAY.
CH
Reproducción Fija
Presione PAUSE/STILL
durante la reproducción
normal para hacer una pausa
en la reproducción.
TRACKING/
SET
–
TRACKING/
SET
+
SELECT/
ENTER
Para seguir con la
reproducción normal,
presione PLAY.
CH
SETUP/
CLEAR/
DVD MENU
RETURN
VCR MENU
CANCEL
MARKER
ZOOM
TOP MENU REPEAT A-B
Avance cuadro por cuadro
Presione PAUSE/STILL durante la
imagen fija.
AUDIO/
JUMP/
ANGLE/
CLOCK/
AUDIO SELECT ZERO RETURN COUNTER RESET COUNTER
Avanza un cuadro cuando presione
PAUSE/STILL una vez.
SUB TITLE/
ATR
PLAY MODE/
SPEED
TIMER REC
TV/VCR
Para seguir con la reproducción
REW/SEARCH
PLAY
SEARCH/F.FWD
normal, presione PLAY.
INDEX/SKIP
REC/OTR
STOP
SKIP/INDEX
SLOW
PAUSE/STILL
Reproducción de cámara lenta
Presione SLOW durante la reproducción normal o cuadro a cuadro.
Cada vez que presione SLOW, cambiará la velocidad del slow x1/
2, x1/4, x1/6, x1/7.
• Para seguir con la reproducción normal, presione PLAY.
• Para volver a la imagen fija, presione PAUSE/STILL.
NOTA:
El aparato puede mantener una imagen
fija de video o la imagen visualizada en
la pantalla, en su pantalla de TV,
permanentemente. Si deja la imagen
fija de video o la imagen visualizada en
la pantalla en su TV durante mucho
tiempo, puede dañar permanentemente
la pantalla de TV. Los televisores de
proyección tienen tendencia a sufrir
este problema.
Búsqueda de un capítulo o canción
Presione SKIP (
) en avance o SKIP (
) en retroceso
durante la reproducción para buscar un capítulo que desea
ver. Cada vez que presione el botón, se salta un capítulo o
canción.
36
2C51001AS(34-37)
36
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Zoom/Búsqueda de la escena deseada
Preparación:
ENCIENDA el TV y ajústelo en el modo de entrada de video.
Presione VCR/DVD para seleccionar el modo DVD. (El
indicador DVD se iluminará.)
•
•
Zooming (acercamiento)
Estaunidadlepermitiráhaceracercamientosdelaimagen
del marco y podrá efectuar selecciones cambiando la
posición del marco.
Presione ZOOM durante
la reproducción.
La parte central de la
imagen se agranda.
Cada vez que presione el
ZOOM cambiará el ZOOM
1
1
1 (x1.3),
3 (x2.0).
2 (x1.5) y
Presione
/
o
/
para ver una parte diferente del
2
3
marco. PuedemoverelmarcodelcentrohaciaUP(arriba),
DOWN (abajo), LEFT (izquierda), RIGHT (derecha).
En el modo ZOOM presione ZOOM varias veces para
regresar a una visión 1:1 (
Off).
Búsqueda de la escena deseada
Utilice el título, capítulo y tiempo grabados en el disco
para buscar el punto que desea reproducir.
Para comprobar el título, el capítulo y el tiempo,
presione DISPLAY (ver página 50).
Presione JUMP durante
la reproducción.
1
Jump
Time
Title
Chapter
/Enter/0 9/Cancel/Jump
2 Presione
o
para seleccionar el título, capítulo o
tiempo.
Presione las teclas numéricas (0-9) para cambiar el
número.
NOTA:
3
Puede seleccionar la reproducción con
pausa, cámara lenta o búsqueda en el
modo zoom.
• Si entra un número equivocado, presione CANCEL.
• Consulte la caja en la que viene el disco para
confirmar los números.
Presione ENTER.
Empieza la reproducción.
4
• Cuando cambie el título, empieza a reproducir desde el
capítulo 1 del título seleccionado.
• Este procedimiento puede no funcionar en algunos
discos.
37
2C51001AS(34-37)
37
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Reproducción repetida
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
• Presione VCR/DVD para seleccionar el modo DVD. (El
indicador DVD se iluminará.)
Reproducción de título, capítulo, canción
Presione PLAY MODE durante la reproducción.
1
DVD
CD
Repeat
:
Off
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
/Enter/Play Mode
Presionar ENTER una o dos veces para seleccionar el Capítulo
o Título.
2
3
Si se trata de un CD, presione
primero para seleccionar
"Repeat" y, a continuación, presione ENTER una o dos veces
para seleccionar "Track" o "All".
DVD
CD
Repeat
:
Chapter
Play Mode
Repeat
:
:
Off
All
/Enter/Play Mode
/Enter/Play Mode
Presionar PLAY MODE nuevamente para que desaparezca la
pantalla.
• Presionar PLAY para iniciar la reproducción repetida.
• Para volver a reproducción normal, seleccionar Repeat Off.
Reproducción repetida A-B
La reproducción repetida A-B le permite repetir el material entre
los dos puntos seleccionados.
Presione REPEAT A-B
durante la reproducción.
Se selecciona el punto inicial.
1
A
NOTAS:
• La función de repetición puede no
funcionar en algunos discos.
• En el modo de repetición A-B pueden
no aparecer los subtítulos cerca del
punto A o B.
• Durante la reproducción repetida la
característica ANGLE no operará.
• Puede no ser posible programar la
repetición A-B en algunas escenas del
DVD.
Presione nuevamente REPEAT
2
A B
A-B. Se selecciona el punto fi-
nal. Empieza a reproducir en el
punto seleccionado.
Lareproducciónsedetieneenel
punto final, vuelve al punto A y
vuelve a empezar nuevamente.
Para continuar con la reproducción normal, presione
nuevamente REPEAT A-B. Aparece “
• La repetición A-B no funciona con un
DVD interactivo y MP3-CD.
” en la pantalla.
Off
38
2C51001AS(38-43)
38
18/11/03, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Programacion de reproduccion/Reproducción aleatoria
(disco compacto)
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
• Presione VCR/DVD para seleccionar el modo DVD. (El
indicador DVD se iluminará.)
Programación de reproducción
Se puede cambiar el orden de las canciones en el disco.
Presione PLAY MODE en el
modo de parada.
1
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
Presione ENTER varias veces
Play Mode
Repeat
:
:
Program
Off
7
8
9
2 hasta que aparezca la tabla de
1
2
3
4
5
6
10
11
12
programas que se muestra a la
derecha.
Clear
Program Playback
/Enter/0 9/Cancel/Play Mode
Ejemplo: Si desea programar
3
Play Mode
Repeat
:
:
Program
Off
en orden 7, 3, 11: Entre como 7
, 3 , 11.
1 7
4
7
8
9
10
11
12
2 3
3 11
Clear
5
6
Si pone un número equivocado,
Presione CANCEL.
Program Playback
/Enter/0 9/Cancel/Play Mode
Presionar
/
o
/
para
4 seleccionar la programación de
Program Playback
reproducción y presionar
ENTER. "Program Playback"
aparecerá en pantalla. Los
programas que seleccionó se
empezarán a reproducir en
orden.
Para volver a la reproducción
normal, seleccione “Play Mode:
Off” en el paso 2 anterior.
Reproducción aleatoria
Presione PLAY MODE en el
modo stop.
1
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
NOTAS:
•
Para cancelar el programa de play,
seleccioneClear(salir)ypresione ENTER.
Presione
seleccionar Random
(aleatorio).
/
para
2
3
Play Mode
Repeat
:
:
Random
Off
• El programa se cancela cuando abra
la bandeja del disco o cuando se
desconecta el aparato.
• La reproducción aleatoria no puede
combinarse con la reproducción
repetida.
/Enter/Play Mode
Presionar PLAY.
“RandomPlay”apareceráenpantallayseiniciarálareproducción
aleatoria.
39
2C51001AS(38-43)
39
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Reproducción de MP3
Esta unidad puede reproducir datos MP3
grabados en un CD-R o CD-RW. Para
reproducir los datos MP3 se necesita un PC
conWindows,unidaddeCD-ROMysoftware
codificador de MP3 (no incluido).
No se puede reproducir el sistema Apple-
HFS.
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
• A continuación, presione VCR/DVD para seleccionar el
modo DVD. (El indicador DVD se iluminará.)
Presione OPEN/CLOSE.
Se abrirá la bandeja del disco.
Coloque un disco en la bandeja.
1
Información de CD MP3
Limitaciones de la reproducción de CD MP3
• El CD MP3 es un disco estandarizado por
ISO9660, su nombre de archivo debe incluir
la extensión de tres caracteres “mp3”.
• El directorio y los nombres de archivo del
CD MP3 deben respetar los de los archivos
estándar ISO.
• Esta unidad puede leer 200 archivos por
disco. Si un directorio tiene más de 200
archivos, lee hasta el archivo 200 y omite
los restantes.
Presione PLAY o OPEN/CLOSE.
Reading
2 La bandeja del disco se cierra
automáticamente. En la pantalla
del TV aparecerá “Reading”. La
lectura llevará tanto tiempo como
requiera el número de archivos.
• Por lo que respecta a los discos multisesión,
sólo se puede reproducir la primera.
• Si el CD tiene tanto pistas de audio como
archivos MP3, sólo se reproducen los
archivos de audio.
• Puede que la unidad tarde más de un minuto
en leer archivos MP3 dependiendo de su
estructura.
• Puede reproducirse música grabada con
“Joliet Recording Specification”, el nombre
de archivo se mostrará en pantalla (hasta 16
letras). Los nombres de archivo largos serán
condensados.
• Los archivos de música grabados mediante
HFS (Hierarchical File System) no pueden
reproducirse.
En la pantalla del TV aparecerá
-
/72 --:--
CD-R
3
4
Pops
Japan
una pantalla de menú MP3.
Presione o ENTER para
seleccionar la carpeta.
1
2
3
4
5
6
7
8
flower
Bay Bridge
CLOSE MY EYES
DIVE TO BLUE
Honey
BLUE EYES
Blurry Eyes
9
Lies and Truth-
winter fall
Rain
Strawberry
Welcome party
Thailand
/
10
11
12
13
14
/0-9/Enter/Play Mode
Presione
/
o
/
o los botones de número para
seleccionar la pista deseada y, a continuación, presione
ENTER. Se selecciona la pista y se inicia la reproducción.
• En caso de que la carpeta incluya más de 15 pistas, presione
o
para que se muestre la siguiente lista de pistas.
-
/72 --:--
CD-R
-/72 --:--
CD-R
Pops
Pops
Limitaciones en el visualizador
1
2
3
4
5
6
7
8
Japan
flower
15
16
Mother
Hold Your Last
Bay Bridge
CLOSE MY EYES
DIVE TO BLUE
Honey
BLUE EYES
Blurry Eyes
9
Lies and Truth-
winter fall
Rain
Strawberry
Welcome party
Thailand
• El número máximo de caracteres mostrado
por el visualizador es 16.Los caracteres que
pueden mostrase son los siguientes: letras
mayúsculas o minúsculas de la A a la Z,
números del 0 al 9, y _ (subrayado).
10
11
12
13
14
/0-9/Enter/Play Mode
/0-9/Enter/Play Mode
• Los caracteres no incluidos en los citados
anteriormente se sustituyen por un guión.
Presione STOP para detener la reproducción.
• La unidad graba el punto de parada. “ ” aparece en
pantalla. Presione PLAY para reanudar la reproducción
(desde el punto de la escena).
• Si presiona de nuevo STOP o extrae el disco, la unidad
borrará el punto de parada.
5
6
Notas sobre archivos MP3
Para reproducir un CD MP3 en el orden en
que se grabó,
1. Utilice software MP3 que grabe datos
alfabética o numéricamente.
2. Nombre cada archivo incluyendo un número
de dos o tres dígitos (p.ej. “01” “02” o “001”
“002”).
3. No cree demasiadas subcarpetas.
PRECAUCIÓN:
• Algunos CD MP3 no podrán reproducirse
dependiendo de las condiciones de
grabación.
• Los CD-R/RW que no contengan datos de
música o archivos MP3 no podrán
reproducirse.
A continuación presione OPEN/CLOSE en el aparato.
Se abre la bandeja del disco.
Saque el disco y presione POWER. La bandeja del disco se
cierra automáticamente y se desconecta el aparato.
NOTAS:
•
Durante la reproducción de MP3, no se pueden utilizar las
funciones SEARCH, A-B Repeat.
Durante la reproducción de un CD MP3 se puede utilizar la
función Repeat (Track o All), las funciones aleatorias y ia
programacion de reproduccion (ver páginas 38 y 39).
•
40
2C51001AS(38-43)
40
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Marcación de escenas deseadas
El aparato memoriza los puntos que
desea ver nuevamente.
Puede continuar la reproducción
desde dicha escena.
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
•
Presione VCR/DVD para seleccionar el modo DVD. (El
indicador DVD se iluminará.)
Marcación de escenas
Presione MARKER
1
Marker
Marker
Marker
1
2
3
durante la reproducción.
/Enter/Cancel/Marker
SeleccionarelMarkerenblanco
2
Marker
Marker
Marker
1
2
3
00 27 54
utilizando
/
, después
presione ENTER en la escena
deseada.
/Enter/Cancel/Marker
•
Repitaesteprocedimientopara
ajustar las otras 2 escenas.
Presione MARKER para que desaparezca este despliegue.
3
Para volver a las escenas
Presione MARKER durante la
1
Marker
Marker
Marker
1
2
3
00 27 54
01
02
reproducción o el modo stop.
16 25
08 31
/Enter/Cancel/Marker
Presione
seleccionar el Marker 1-3.
o
para
2
3
Marker
Marker
Marker
1
2
3
00 27 54
01
02
16 25
08 31
/Enter/Cancel/Marker
NOTAS:
Presione ENTER.
La reproducción empieza desde la escena marcada.
• Es posible que algunos discos no
admitan la función de marcación.
• La marcación se cancela cuando abra
la bandeja del disco o desconecta el
aparato.
Para cancelar la marca
• Algunos subtítulos grabados cerca del
marcador puede no aparecer.
Presione MARKER.
1
2
3
Presione
o
para seleccionar el Marker 1-3.
Presione CANCEL.
Para eliminar este visualizador, presione MARKER.
41
2C51001AS(38-43)
41
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Cambio del idioma de la pista de sonido /
Subtítulos / Reproducción de karaoke
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
• Presione VCR/DVD para seleccionar el modo DVD. (El
indicador DVD se iluminará.)
CAMBIO DEL IDIOMA DE LA PISTA DE SONIDO
Se puede seleccionar el idioma cuando reproduce un disco en
múltiples idiomas.
Presione AUDIO durante la
reproducción.
Aparecerá el idioma actual de la
1
1/8 Eng DolbyDigital
pista de sonido.
Presione AUDIO hasta que
2 quede seleccionado el idioma
2/8 Fra DolbyDigital
deseado.
El despliegue en pantalla
desaparecerá después de unos
cuantos segundos.
Aparición y desaparición de subtítulos
Cuando reproduzca un disco con subtítulos grabados, puede
hacer que éstos aparezcan o desaparezcan.
Presione SUB TITLE durante la
reproducción hasta que aparezca
Off
“Off”.
NOTAS:
• Si no puede seleccionar el idioma deseado
despuésdepresionarelbotónvariasveces,
el idioma no fue grabado en el disco.
• Se cancela el cambio del idioma de los
subtítuloscuandoabralabandejadeldisco
o desconecte el aparato o apague el
aparato.
• Dependiendo del DVD quizá no pueda
activar, desactivarocambiarlossubtítulos,
incluso si están grabados en el disco. Al
reproducir el DVD, el subtítulo puede
cambiar cuando se abre o cierra la bandeja
del disco, o cuando se cambia el título.
• Enalgunoscaso,elidiomadelossubtítulos
nocambiainmediatamentealseleccionado.
• La función de salida vocal se emplea
durante la reproducción de discos DVD
KARAOKE grabados con Dolby Digital
(multicanal). Esta función permite
desactivar las pistas de sonido de voz, o
restaurarlas para acompañamiento de
fondo.
Cambio del idioma de los subtítulos
Puede seleccionar el idioma para reproducir un disco
grabado con subtítulos en múltiples idiomas.
Presione SUB TITLE durante la
reproducción hasta que aparezca el
idioma deseado.
El despliegue en pantalla
desaparecerá después de unos
cuantos segundos.
1/32 Eng
Reproducción de karaoke
AlreproducirundiscoDVDKARAOKE,puedeactivarodesactivarlaspistas
de voz.
Presione AUDIO durante la
reproducción del disco DVD
KARAOKE.
1
1/8 Eng DolbyDigital
On
Presione
“On” u “Off”.
On: Las voces principales se
reproducen cuando están
o
paraseleccionar
• Al reproducir KARAOKE, conecte un
equipo de sonido apropiado (como un
amplificador) al DVD/VCR.
2
grabadas en el disco.
Off: Las voces principales no se reproducen.
42
2C51001AS(38-43)
42
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Cambio de ángulos / Selección de título / Menú DVD
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
• Presione VCR/DVD para seleccionar el modo DVD. (El
indicador DVD se iluminará.)
Cambio de ángulos
Cuando reproduce un disco grabado en múltiples ángulos,
puede cambiar el ángulo de visión de la escena.
Presione ANGLE durante la
reproducción. Aparecerá el an-
gle actual.
1
1/9
Presione ANGLE varias veces hasta que seleccione el angle
deseado.
2
Selección de título
Hay dos o más títulos grabados en algunos discos. Si se ha
grabado el menú de título en el disco, puede seleccionar el
título deseado.
Presione TOP MENU durante la reproducción.
El menú de títulos aparece en pantalla.
• Presione de nuevo TOP MENU para reanudar la reproducción
1
en la escena en la que había presionado TOP MENU.
Presione
/
o
/
para seleccionar el título deseado.
2
3
Presione ENTER o PLAY.
Empieza la reproducción del título seleccionado.
Menú DVD
Algunos DVD permiten seleccionar el contenido del disco
con el menú.
Cuando reproduce este tipo de DVD, puede seleccionar el
idioma de los subtítulos, idioma de la pista de sonido, etc.
con el menú DVD.
Presione DVD MENU durante la reproducción.
1 Aparece el menú DVD en la pantalla.
NOTA:
• Presione nuevamente DVD MENU para volver a reproducir
la escena en la que se estaba reproduciendo cuando
presionó DVD MENU.
En algunos DVD, puede no ser posible
cambiar los ángulos incluso cuando se
grabó en múltiples ángulos en el disco, o
quizá no pueda seleccionar el título, y un
“menú de títulos” puede simplemente
llamarse un “menú” o “título” en las
instrucciones suministradas con el disco.
Presione
/
o
/
para seleccionar el ítem deseado.
2
3
Presione ENTER.
El menú continúa en otra pantalla. Repita los pasos 2 y 3 para
terminar de seleccionar el ítem completamente.
43
2C51001AS(38-43)
43
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Ajuste de restricciones para menores
Algunos discos están especificados
como inapropiados para niños.
Puede restringir la reproducción de
tales discos en la unidad.
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
• Presione VCR/DVD para seleccionar el modo DVD. (El
indicador DVD se iluminará.)
AJUSTE DE RESTRICCIONES PARA MENORES
Language Picture Sound Parental Other
PresioneSETUPenelmododeparada.
1
Presione
o
para seleccionar.
Password
Parental
Off
Presione
o ENTER.
0
9/Cancel
/Enter/Setup/Return
Presione
una vez para seleccionar
Language Picture Sound Parental Other
Password
2
3
“Parental Off”y, a continuación, presione
ENTER hasta que aparezca el nivel
deseado (p. ej.: 1).
Parental
1
/Enter/Setup/Return
Presione
una vez para seleccionar “
”.
A continuación presione los botones de
número para entrar una contraseña de
4 dígitos (p. ej.: 1234).
Language Picture Sound Parental Other
Password
Parental
1234
1
• Si entra un número de contraseña
equivocado, presione CANCEL.
• Asegúrese de recordar su número!
0
9/Cancel
/Enter/Setup/Return
• Nivel Off : El ajuste de restricciones para menores no funciona.
• Nivel 1 : El DVD para mayores no puede reproducirse.
• Nivel 8 : Se puede reproducir todo el DVD.
• Seleccione entre el nivel 1 al nivel 8. En una escala del 1 al 8,
“1” es el más restrictivo.
Presione ENTER.
Language Picture Sound Parental Other
4
5
1234
cambiar a
.
Password
Parental
1
0
9/Cancel
/Enter/Setup/Return
Para que desaparezca la pantalla de ajuste, presione SET UP.
NOTAS:
Para desbloquear el ajuste de restricciones
para menores
• Una vez completado cada ajuste
(P.44-51), el aparato puede seguir
funcionando en las mismas
condiciones (especialmente con
discos DVD).
Cada ajuste puede mantenerse en la
memoriaaunquedesconecteelaparato.
• Paraalgunosdiscos,elapartonopuede
prohibir la reproducción.
• Algunos discos no puede codificarse
con determinada información de nivel
de prohibición aunque la etiqueta del
discodiga“adulto”. Paraestosdiscosno
funcionará la prohibición para menores.
• No olvide la contraseña. Si olvida la
contraseña, póngase en contacto con
el servicio al cliente.
Cancelelacontraseñaparaajustarlibrementeelnivelderestricciones
para menores,
Language Picture Sound Parental Other
Seleccione “Password
”(paso
1
2
Password
Parental
1234
1
2) y presione los botones de número
para entrar la contraseña de 4 dígitos.
A continuación, presione ENTER.
0
9/Cancel
/Enter/Setup/Return
Si la contraseña entrada era correcta,
aparecerá
Puede desplazarse a “Parental 1”, por
ejemplo, para entrar el nivel deseado o
para cancelar el control de restricciones.
Language Picture Sound Parental Other
Password
.
Parental
1
0
9/Cancel
/Enter/Setup/Return
44
2C51001AS(44-49)
44
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Deshabilitación temporal del nivel de rating (clasificación)
del disco DVD
Dependiendo del disco DVD, el disco
puede tratar de cancelar temporalmente
el nivel de rating que haya ajustado.
Depende de usted si decide cancelar
el nivel de la rating o no.
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
• Presione VCR/DVD para seleccionar el modo DVD. (El
indicador DVD se iluminará.)
Introduzca el disco DVD y
1
presionePLAYoOPEN/CLOSE
en la unidad (ver pág. 35).
Si el disco DVD fue diseñado para cancelar temporalmente el
2
nivel del Rating, cambiará la pantalla que aparece después del
“Reading” (lectura) dependiendo del disco que se esté tocando.
Si selecciona “YES” con ENTER aparecerá la pantalla de “su
disco excede el nivel de restricciones para menores”.
Lectura
Su seleccion excede el
Limite del indice nivel#.
Nivel de Indice
Cancelar Imagen
/Enter/Return
Si desea cancelar el nivel de clasificación ajustado
temporalmente, seleccione “Parental Control Level” con
y después presione ENTER. Si se estableció la
3
o
contraseña de 4 dígitos del paso 3 de la pag. 44, aparecerá la
pantalla de entrar contraseña como aparece en el paso 4.
Alternativamente, si no se ha establecido ninguna contraseña,
comenzará la reproducción. Si desconoce (u olvidó) la
contraseña, seleccione “Cancel Picture”.
La pantalla de ajuste desaparecerá. Presione OPEN/CLOSE
para sacar el disco.
Entre la contraseña con los
BOTONES DE NÚMERO (0-9).
Después, presione ENTER.
4
5
Please enter the
digit password
4
Si interrumpe la introduccion
de la contraseña, presione
RETURN.
Enter/0 9/Cancel/Return
La reproducción comenzará si se introdujo la contraseña
correcta.
NOTA:
Esta cancelación temporal del nivel del rat-
ing se mantendrá hasta que se saque el
disco. Cuando se extraiga el disco se
establecerá el nivel de rating original de
manera automática.
45
2C51001AS(44-49)
45
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Selección del idioma del menú
Se puede seleccionar el idioma de los
mensajes del menú de disco de los
DVD.
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
•
Presione VCR/DVD para seleccionar el modo DVD. (El
indicador DVD se iluminará.)
Presione SETUP en el modo de
parada o no hay disco.
Language Picture Sound Parental Other
1
Presione
o
paraseleccinar
Language.
/Enter/Setup/Return
Presione o ENTERypresione
Language Picture Sound Parental Other
2
3
o
para seleccionar Menu
Menu
Subtitle
Audio
English
Automatic
English
/Enter/Setup/Return
Presione
Presione
o ENTER.
Language Picture Sound Parental Other
o
para
Menu
Subtitle
Audio
English
Automatic
English
English
Francais
Espanol
Other
seleccionar su idioma deseado
y presione ENTER.
/Enter/Setup/Return
English, Francais, Espanol:
El idioma seleccionado es el idioma prioritario del Menú.
Other:
Se puede seleccionar otro idioma.
(Consulte la lista de códigos de idioma en la página 53)
Para que desaparezca la pantalla SETUP, presione SETUP.
4
46
2C51001AS(44-49)
46
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Selección del idioma de los subtítulos
Preparación:
Sepuedeseleccionarsiempreelmismo
idioma de subtítulos aunque cambie
de disco o desconecte el aparato.
ENCIENDA el TV y ajústelo en el modo de entrada de video.
Presione VCR/DVD para seleccionar el modo DVD. (El
indicador DVD se iluminará.)
•
•
Presione SETUP en el modo de
Language Picture Sound Parental Other
1
2
3
parada o no hay disco.
Presione para
seleccionar Language.
o
/Enter/Setup/Return
Language Picture Sound Parental Other
Presione
presione
o ENTER y
para
o
Menu
Subtitle
Audio
English
Automatic
English
seleccionar Subtitle.
/Enter/Setup/Return
Language Picture Sound Parental Other
Presione
Presione
o ENTER.
para
o
Menu
Subtitle
Audio
English
Automatic
English
English
Francais
Espanol
Other
seleccionar su idioma
deseado y presione ENTER.
Automatic
Off
/Enter/Setup/Return
English, Francais, Espanol:
Aparece el subtítulo con el idioma seleccionado si está
registrado en el disco.
Other:
Si desea seleccionar otro idioma, entre el código de
idioma (consulte la lista de códigos de idioma en la
página 53).
Automatic:
• El aparato seleccionará automáticamente el mismo idioma
seleccionado para el AUDIO.
• Cuando el aparato selecciona el mismo idioma que para el
AUDIO los subtítulos no aparecen durante la reproducción.
• Cuando no utilice el mismo idioma que el AUDIO, los
subtítulos aparecerán durante la reproducción.
NOTA:
Off:
Si el idioma seleccionado no se grabó
en el disco, se selecciona el idioma de
máxima prioridad.
No aparecen subtítulos.
Para que desaparezca la pantalla SETUP, presione SETUP.
4
47
2C51001AS(44-49)
47
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Selección del idioma de la pista de sonido de audio
Se puede seleccionar el mismo
idioma de la pista de sonido de audio
incluso aunque cambie de disco o
desconecte el aparato.
Preparación:
ENCIENDA el TV y ajústelo en el modo de entrada de video.
A continuación, presione VCR/DVD para seleccionar el modo
DVD. (El indicador DVD se iluminará.)
•
•
Presione SETUP en el modo de
parada o no hay disco.
Language Picture Sound Parental Other
1
2
3
Presione
o
para seleccionar
Language.
/Enter/Setup/Return
Presione
presione
o ENTER y
para
Language Picture Sound Parental Other
o
Menu
Subtitle
Audio
English
Automatic
English
seleccionar Audio.
/Enter/Setup/Return
Language Picture Sound Parental Other
Presione
Presione
o ENTER.
para
o
Menu
Subtitle
Audio
English
Automatic
English
English
Francais
Espanol
Other
seleccionar el Idioma de
Audio deseado y después
presione ENTER.
Original
/Enter/Setup/Return
English, Francais, Espanol:
Se escuchará el idioma deseado si está registrado en el
disco.
Other:
Si desea seleccionar otro idioma, entre el código del
idioma. (Consulte la lista de códigos de indioma en la
página 53.)
Original:
El aparato seleccionar el idioma de máxima prioridad en
cada disco.
Para que desaparezca la pantalla SETUP, presione SETUP.
4
NOTA:
Si el idioma seleccionado no está grabado
eneldisco, seescucharáelidiomaoriginal.
48
2C51001AS(44-49)
48
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Ajuste de la relación de aspecto de la pantalla de TV
Se puede seleccionar la relación de
Preparación:
aspecto para su TV.
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
• Presione VCR/DVD para seleccionar el modo DVD. (El
indicador DVD se iluminará.)
Language Picture Sound Parental Other
Presione SETUP en el modo de
parada o no hay disco.
1
2
3
Presione
o
para
seleccionar Picture.
/Enter/Setup/Return
Presionar
o ENTER,
Language Picture Sound Parental Other
después presionar
o
Tv Screen
Display
4:3
On
para seleccionar la pantalla de
TV.
/Enter/Setup/Return
Presione
Presione
o ENTER.
para
Language Picture Sound Parental Other
o
Tv Screen
Display
4:3
On
4:3
4:3
seleccionar su tipo de pantalla
deseado y presione ENTER.
16:9
/Enter/Setup/Return
Puede escoger entre los siguientes tamaños de pantalla:
4:3 : Letter box
Seleccione este modo cuando ese ha conectado a un TV
convencional, cuando se reproducen discos DVD de pantalla
ancha.
Muestra la imagen ancha con bandas negras arriba y abajo
de la pantalla.
4:3
: Pan Scan
Muestra la imagen ancha en toda la pantalla con los bordes
izquierdo y derecho cortados automáticamente.
16:9
: Wide
Seleccione este modo cuando conecte un TV de pantalla
ancha. Aparece una imagen en pantalla ancha a su tamaño
máximo.
NOTA:
Si no se ha formateado el disco DVD en
el estilo pan y scan, aparece en el estilo
4:3.
Para que desaparezca la pantalla SETUP, presione SETUP.
4
49
2C51001AS(44-49)
49
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Selección de las indicaciones en la pantalla/
Datos del status del Disco
Preparación:
Aparecen o desaparecen las
indicaciones en la pantalla cuando
presione los botones DISPLAY.
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
•
Presione VCR/DVD para seleccionar el modo DVD. (El
indicador DVD se iluminará.)
Presione SETUP en el modo de
parada o no hay disco.
Language Picture Sound Parental Other
1
Presione
o
para
seleccionar Picture.
/Enter/Setup/Return
Presione
presione
seleccionar Display.
o ENTER y
para
Language Picture Sound Parental Other
2
3
o
Tv Screen
Display
4:3
On
/Enter/Setup/Return
Language Picture Sound Parental Other
Presione
seleccionar On o Off.
o ENTER para
Tv Screen
Display
4:3
Off
/Enter/Setup/Return
On: Aparecen las indicaciones en la pantalla cuando
presione los botones (ajuste de fábrica).
Off: No aparecen las indicaciones en la pantalla cuando
presione los botones salvo SETUP, SEARCH MODE,
PLAY MODE, MARKER y DISPLAY.
Para que desaparezca la pantalla SETUP, presione SETUP.
4
Datos del status del Disco
Cada vez que presione DISPLAY aparecerán los datos del status
del disco en la pantalla y cambiará de la siguiente manera.
DVD
00:34:56 01:12:33
00:34:56 01:12:33
1/99 Chapter 1/999
1/9
Title
1/8 Eng DolbyDigital
1/32 Eng
Para que desaparezca el status del disco, presione
DISPLAY nuevamente.
Disco compacto de audio
34:56
71:33
Track 11/99
Al reproducir el disco CD, la visualización del estado
aparecerá en la pantalla y continuará mostrándose.
50
2C51001AS(50-BACK)
50
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Control de la Gama Dinámica
ElDRC(ControldelaGamaDinámica)
le permite controlar la gama dinámica
para obtener un sonido conveniente
para su equipo.
Preparación:
• ENCIENDA el TV y ajústelo en el modo de entrada de video.
•
Presione VCR/DVD para seleccionar el modo DVD.
(El indicador DVD se iluminará.)
Presione SETUP en el modo de
Language Picture Sound Parental Other
1
parada. Presione
o
para
seleccionar “Sonido”.
/Enter/Setup/Return
Presione
seleccionar “DRC”.
o ENTER para
Language Picture Sound Parental Other
2
3
DRC
Std
/Enter/Setup/Return
Language Picture Sound Parental Other
Presione
o ENTER, a
Max
Std
Min
continuación presione
para seleccionar la configuración
deseada.
o
Std
DRC
/Enter/Setup/Return
Max: La gama dinámica total aumenta.
Std: La gama dinámica total se mantiene.
Min: La gama dinámica se reduce.
NOTAS:
• Esta función sólo se activa durante la
reproducción de discos grabados Dolby Dig-
ital.
• El nivel de Reducción de la Gama Dinámica
podrá ser diferente dependiendo del disco
de vídeo DVD.
51
2C51001AS(50-BACK)
51
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploración progresiva
La unidad admite el sistema de
exploración progresiva, además del
sistema convencional de exploración
entrelazada.Sisutelevisorcuentacon
tomas de componentes que admiten
la entrada de vídeo progresivo, podrá
disfrutar de imágenes de gran calidad
activando el modo de exploración
progresiva.
Preparación:
• Conecte la unidad a un televisor con tomas de componentes.
• Encienda el televisor y seleccione el modo correspondiente de
entrada de vídeo.
• Ajuste el selector de vídeo S-VIDEO / COMPONENT del panel
trasero a la posición COMPONENT.
• Presione VCR/DVD para seleccionar el modo DVD.
(El indicador DVD se iluminará.)
Presione PROGRESSIVEen el modo de parada. Se enciende el
indicador PROGRESSIVE “ ” de la ventana de visualización.
1
• La unidad reconoce el origen de la imagen (película o vídeo)
del disco actual, según la información del disco.
Presione PLAY para comenzar la reproducción.
2
• Para desactivar el modo de exploración progresiva, presione
PROGRESSIVE en el modo de parada. Se apagará el
indicador PROGRESSIVE “ ” de la ventana de visualización.
Selector de vídeo
S-VIDEO/COMPONENT
Acerca del MODO DE EXPLORACIÓN PROGRESIVA
Para visualizar vídeo en una pantalla de televisión, el método
convencional de exploración se denomina “exploración
entrelazada”.Conestemétodo,encadamomentosólosevisualizan
la mitad de las líneas horizontales. De esta forma, dos campos
completanunaimagen(fotograma). Esdecir, elprimercampo, que
contiene las líneas impares, se muestra seguido del segundo
campo, que contiene las líneas pares.
El sistema de exploración progresiva barre todas las líneas
horizontales al mismo tiempo, de forma que se puede doblar el
número de líneas en comparación con la exploración entrelazada,
lo que genera una imagen con mayor resolución y sin parpadeo.
Para poder ver vídeo con exploración progresiva, el televisor que
esté conectado a la unidad debe tener entradas progresivas.
Dependiendodelformatodeorigendelmaterial, losdiscosDVDse
pueden clasificar en dos categorías: películas y vídeo (algunos
discosDVDcontienenorigentantodepelículacomodevídeo). Los
orígenes de película se graban con información presentada a 24
fotogramas por segundo, mientras que los de vídeo (NTSC) se
grabana30fotogramasporsegundo(60camposporsegundo,con
entrelazado).
Cuando la unidad reproduce un material con origen de película, se
crean señales de salida progresiva no entrelazada a partir de la
información original.
Cuando se reproduce un material con origen de vídeo, la unidad
interpola líneas entre las líneas entrelazadas para crear la imagen
interpolada y la suministra como imagen progresiva.
NOTAS:
• Puede que algunos discos no se reproduzcan correctamente con el modo de exploración progresiva, debido a
las características del disco o a su estado de grabación.
• Hay algunos televisores progresivos y de alta definición que no son totalmente compatibles con la unidad, lo que
provocará la presentación de una imagen poco natural cuando se reproduzca un disco DVD en modo de
exploración progresiva. En ese caso, utilice el modo de exploración entrelazada.
• No se puede activar el modo de exploración progresiva en los siguientes casos.
– Cuando la unidad está en modo VCR.
– Cuando el disco se está reproduciendo en modo DVD.
– Cuando el selector de vídeo S-VIDEO / COMPONENT está en la posición S-VIDEO.
52
2C51001AS(50-BACK)
52
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Lista de códigos de idiomas
Entre el número de código apropiado para los ajustes iniciales “AUDIO”, “SUB TITLE” y/o “MENU
LANGUAGE” (consulte las páginas 46-48).
Language Name Code Language Name Code Language Name Code Language Name Code
Abkhazian
Afar
1112 Fiji
1620 Lingala
1619 Lithuanian
1628 Macedonian
1635 Malagasy
1722 Malay
2224 Singhalese
2230 Slovak
2321 Slovenian
2317 Somali
2329 Spanish
2322 Sundanese
2330 Swahili
2319 Swedish
2328 Tagalog
2325 Tajik
2919
2921
2922
2925
1529
2931
2933
2932
3022
3017
3011
3030
3015
3018
1225
3019
3025
3028
3021
3033
3121
3128
3136
3219
3225
1335
3325
3418
2019
3525
3631
1111 Finnish
1116 French
2927 Frisian
1123 Galician
1128 Georgian
1835 German
1129 Greek
Afrikaans
Albanian
Amharic
Arabic
2111 Malayalam
1415 Maltese
1522 Maori
Armenian
Assamese
Aymara
1135 Greenlandic
1136 Guarani
1211 Gujarati
1531 Hausa
2122 Marathi
1724 Moldavian
1731 Mongolian
1811 Nauru
Azerbaijani
Bashkir
2324 Tamil
Basque
2411 Tatar
Bengali; Bangla 1224 Hebrew
1933 Nepali
2415 Telugu
2425 Thai
Bhutani
Bihari
1436 Hindi
1819 Norwegian
1831 Oriya
1218 Hungarian
1228 Icelandic
1217 Indonesian
2335 Interlingua
1215 Irish
2528 Tibetan
2611 Tigrinya
Breton
1929 Panjabi
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
1924 Pashto, Pushto 2629 Tonga
1911 Persian
1711 Polish
1611 Turkish
2622 Turkmen
2630 Twi
2123 Italian
1930 Portuguese
2011 Quechua
1311 Japanese
3618 Javanese
1325 Kannada
1828 Kashmiri
1329 Kazakh
1411 Kirghiz
2422 Korean
1524 Kurdish
1525 Laothian
1530 Latin
2731 Ukrainian
2033 Rhaeto-Romance 2823 Urdu
2124 Romanian
2129 Russian
2121 Samoan
2135 Sanskrit
2125 Scots Gaelic
2131 Serbian
2825 Uzbek
2831 Vietnamese
2923 Volapük
2911 Welsh
1714 Wolof
Danish
Dutch
English
2928 Xhosa
Esperanto
Estonian
Faroese
2225 Serbo-Croatian 2918 Yiddish
2211 Shona
2924 Yoruba
2914 Zulu
1625 Latvian, Lettish 2232 Sindhi
53
2C51001AS(50-BACK)
53
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Problemas y localización de averías
Utilice la siguiente lista de verificación de localización de averías cuando tiene problemas con este aparato.
Consulte con su concesionario local o tienda de servicio si continúan los problemas.
Compruebe que se han hecho correctamente todas las conexiones cuando utilice con otros aparatos.
SINTOMA
POSIBLE SOLUCION
Página
DVD/VCR
• Verifique que el cable de alimentación esté conectado.
• Pruebe con otro tomacorriente de CA.
• La alimentación está desconectada; revise el fusible o el
interruptor automático.
5
–
–
El DVD/VCR no funciona.
•
Desconecte la unidad, y vuelva a conectarla al cabo de una hora.
5
• Seleccione primero el modo DVD o VCR.
18,34
• La conexión de antena no es la correcta o el cable de antena
está desconectado.
12~15
• El canal de video no está en la posición correcta.
• El canal de TV no está en el canal 3 ó 4.
• El selector de entrada de vídeo del TV no se ha ajustado en
VIDEO. Ajústelo en VIDEO (o equivalente).
• El canal se ha ajustado en el modo externo.
18
12~17
–
Ausencia de imagen.
No hay sonido.
–
• Compruebe que el selector de entrada del amplificador está
en la posición correcta.
12~17
• Seleccionar la posición correcta de la Salida de Audio en el
amplificador AV.
–
• El aparato está en un modo de reproducción especial.
24,36
• Apunte el mando a distancia hacia el sensor remoto.
•
Utilice a una distancia de menos de 5 metros o baje la luz en la habitación.
11
• Elimine los obstáculos para el rayo infrarrojo.
• Las pilas están gastadas. Cambie las pilas.
• Compruebe que las pilas están bien colocadas.
No funciona el mando a distancia.
• Revise todas las conexiones del sistema CATV.
• La estación o el servicio de TV cable están con problemas;
pruebe con otra estación.
La recepción CATV no es posible.
14,15
VCR
•
Las lengüetas de prevención de borrado del video están quebradas.
La grabación no funciona.
22,26
• La unidad está en el modo de entrada externa.
• La hora no ha sido fijada correctamente.
• El comienzo y término de la grabación no se ha fijado
correctamente.
19
29
La grabación con
temporizador no funciona.
• El botón TIMER REC no han sido presionados (El Símbolo
TIMER REC no está visualizador).
29
• Ajuste el tracking más allá del rango del circuito automático.
• Las cabezas del video están sucios.
• La cinta está dañada o gastada.
24
55
–
Barras de ruido en la pantalla.
DVD
La lengua deseada no se
muestra.
• Select proper language in the menu options.
34
• No hay disco colocado.
• El disco puede estar sucio. Limpie el disco.
• El aparato no puede reproducir DVD-ROM, etc.
35
33
33
No empieza la reproducción.
No puede parar la reproducción,
búsqueda, cámara lenta,
reproducción repetida o
• Algunos discos pueden no aceptar algunas
funciones.
–
reproducción programada, etc.
54
2C51001AS(50-BACK)
54
18/11/03, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Problemas y localización de averías / Limpieza de la cabeza de video
Página
SINTOMA
POSIBLE SOLUCION
• El sector S-VIDEO/COMPONENT no está ajustado
correctamente.
16
No se ve la imagen, o la pantalla
está borrosa o dividida en dos partes.
• El modo de exploración progresiva está activo en la unidad
conectada a un televisor a través de la salida VIDEO OUT.
52
• El ajuste no corresponde al de su TV.
• Seleccione Display On.
No se ve la imagen en 4:3 (16:9).
No hay indicaciones en la pantalla.
Noseescuchaelsonidoambiental.
49
50
17
–
• El ajuste no corresponde al de su sistema estéreo.
Una tecla del aparato o mando a
distancia no lo hace funcionar.
• Desconecte el aparato y desenchufe el cable eléctrico de CA
durante varios minutos. Vuelva a enchufar.
No empieza la reproducción al
seleccionar el título.
• Verifique el ajuste del nivel de prohibición.
44
El idioma de la pista de sonido de
audio y/o subtítulos no cambia al
reproducir un DVD.
• No se han grabado múltiples idiomas en el disco DVD.
47,48
• Algunos discos no tienen subtítulos.
• Los subtítulos se han eliminado. Presione SUB TITLE.
No se ven los subtítulos.
42,47
• No se ha grabado desde múltiples ángulos en el disco DVD.
No cambia el ángulo.
43
–
Aparece
en la pantalla.
• La función está prohibida para este aparato o disco.
LIMPIEZA DE LA CABEZA DE VIDEO
OBSTRUCCION DE LAS CABEZAS DE VIDEO
Las cabezas de video constituyen el mecanismo por el que
el DVD/VCR lee las imágenes de la cinta durante la
reproducción. En el caso poco probable de que las cabezas
se ensucien lo suficiente como para quedar obstruidas,
ninguna imagen será reproducida. Esto se puede determinar
fácilmente si, durante la reproducción de una buena cinta
de video, se emite un sonido de calidad, pero no se produce
imagen alguna (la imagen está extremadamente “nevada”).
De ser así, use un sistema de limpieza de cabezas de alta
calidad o haga que las limpien profesionalmente.
Buena imagen
Imagen “nevada”
NOTAS: NO INTENTE LIMPIAR LAS CABEZAS DE VIDEO O REPARAR LA UNIDAD QUITANDO LA CUBIERTA
•
SUPERIOR.
• Las cabezas de video pueden finalmente llegar a desgastarse y tendrán que ser cambiadas cuando
sean incapaces de producir imágenes claras.
• Para ayudar a prevenir la obstrucción de las cabezas de video, utilice solamente cintas VHS de
buena calidad. Deseche cintas desgastadas.
Para informacion adicional sobre los ajustes u operacion, favor de visitar nuestra pagina web
www.memorexelectronics.com o llamar a servicio a clientes al no. 1-800-919-3647
Favor de conservar todo el empaque por lo menos por 90 dias en caso de que tenga que de volver
este producto al lugar de compra o a memorex para obtener refacciones y accesorios, comunicarse
a fox int’l al no. 1-800-321-6993
55
2C51001AS(50-BACK)
55
18/11/03, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Especificaciones
GENERALIDADES
Fuente de alimentación:
120 V CA, 60 Hz
Consumo de energía:
Operation: 18 Vatios
Stand by: 2 Vatios
Peso:
Dimensiones:
7,9 libras (3,6 kg)
Anchura : 16-15/16 pulgadas (430 mm)
Altura : 3-7/8 pulgadas (99 mm)
Profundidad : 9-15/16 pulgadas (253 mm)
Entradas/Salidas:
Entrada de video:
Salida de video:
Entrada de audio:
Salida de audio:
Antena:
1 Vp-p/75 ohmios
1 Vp-p/75 ohmios
–8 dBm/50 k ohmios
–8 dBm/1 k ohmios
UHF/VHF 75 ohmios coaxial
Respuesta de frecuencia Hi-Fi: 20 Hz a 20,000 Hz
Gama dineámica de Hi-Fi:
Mayor de 90 dB
VCR
Video cabezas:
Pistas de audio:
4 cabezas
Sonido Hi-Fi - 2 pistas
Sonido monofónico - 1 pista
181 canales de frecuencia sintetizada
VHF 2 - 13
Sintonizador:
UHF 14 - 69
CATV 14 - 36 (A) - (W)
37 - 59 (AA) - (WW)
60 - 85 (AAA) - (ZZZ)
86 - 94 (86) - (94)
95 - 99 (A-5) - (A-1)
100 - 125 (100) - (125)
01 (5A)
Salida de canal RF:
Tiempo de avance
Canales 3 ó 4
rápido/rebobinado en 25˚C (77˚F): Approximadamente 1 minuto y 48 segundos (con videocassette T-120)
Tocadiscos de DVD/Discos
compactos
Señal de Sistema:
NTSC
Disco utilizable:
DVD (12 cm, 8 cm)
CD (12 cm, 8 cm)
Características de audio
respuesta de frecuencia:
DVD: 4 Hz - 22 kHz
CD: 4 Hz - 20 kHz
S/N Ratio:
90 dB
0,02%
Distorsión armónica:
Variaciones de velocidad:
Gama dinámica:
Salidas:
Menos de 0,01%Wrms
Mayor de 90 dB
Video : (RCA) 1 Vp-p/75 ohmios
Audio : (RCA) –12 dBm/1 k ohm
Audio digital : 0,5 Vp-p/75 ohmios
Captor:
CD :
Longitud de onda: 775 – 805 nm
Potencia máxima de salida: 0,5 mW
Longitud de onda: 640 – 660 nm
Potencia máxima de salida: 1,0 mW
DVD :
Accesorios:
Control Remoto x 1
Cable Coaxial de 75 ohmios x 1
Cordón AUDIO/VIDEO x 1
Memcorp,Inc.
Weston,FL 33331
Printed in Thailand Impreso en Tailandia
Visit our website at www.memorexelectronics.com
Visite nuestro portal de internet en www.memorexelectronics.com
Z
03/12
2C51001AS(50-BACK)
56
18/11/03, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Kyocera Printer KM C1530 User Manual
Leica Camera Lens APO TELYT R User Manual
Magnadyne Stereo Receiver M1 LCD User Manual
Magnavox CRT Television 39MF412B User Manual
Magnavox Stereo System US2 MANT901 User Manual
Makita Saw JS1670 User Manual
Makita Trimmer JS8000 User Manual
Melissa Fryer 643 047 User Manual
Memorex Handheld TV portable user User Manual
Metra Electronics Radio 71 6522 User Manual