MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 22
CD CLOCK STEREO RADIO WITH DUAL
ALARM
MODEL: MMG-CR2900
BEFORE OPERATING THIS PRODUCT,
PLEASE READ THESE INSTRUCTIONS COMPLETELY.
OPERATING INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 2
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT SAFETY INSTRUCTIONS
Before using the unit, be sure to read all operating 8. ACCESSORIES
instructions carefully. Please note that these are
general precautions and may not pertain to your
unit. For example, this unit may not have the
capability to be connected to an outdoor antenna.
1. READ INSTRUCTIONS
Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may
fall, causing serious injury and serious damage to
the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the
All the safety and operating instructions should be
read before the product is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be
retained for future reference.
3. HEED WARNINGS
manufacturer or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use a
mounting accessory recommended by the
manufacturer.
PORTABLE CART WARNING
(symbol provided by RETAC)
8A. An appliance and cart combination
All warnings on the product and in the operating
instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
All operating and use instructions should be
followed.
and cart combination to overturn.
9. VENTILATION
5. CLEANING
Slots and openings in the cabinet and in the back
or bottom are provided for ventilation and to
ensure reliable operation of the product and to
protect it from overheating. These openings must
not be blocked or covered. The openings should
never be blocked by placing the product on a
bed, sofa, rug, or other similar surface. This
product should never be placed near or over a
radiator or heat source. This product should not
be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is
provided or the manufacturer's instructions have
been adhered to.
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. ATTACHMENTS
Do not use attachments not recommended by the
product's manufacturer as they may cause
hazards.
7. WATER AND MOISTURE
Do not use this product near water- for example,
near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near a
swimming pool.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 3
IMPORTANT SAFETY INSTRUCTIONS (CONTINUED)
10. POWER SOURCES
18. REPLACEMENT PARTS
This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply to your home, consult your appliance
dealer or local power company. For products
intended to operate from battery power, or other
sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION
This product is equipped with a polarized
alternating-current line plug (a plug having one
blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
When replacement parts are required, be sure
the service technician uses replacement parts
specified by the manufacturer or those that have
the same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock or other hazards.
19. SAFETY CHECK
Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
proper operating condition.
20. WALL OR CEILING MOUNTING
The product should be mounted to a wall or
ceiling only as recommended by the
manufacturer.
21. DAMAGE REQUIRING SERVICE
Unplug the product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
13. LIGHTNING
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an adjustment of other controls
may result in damage and will often require
extensive work by a qualified technician to restore
the product to its normal operation.
To protect your product from a lightning storm, or
when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will
prevent damage to the product due to lightning
and power-line surges.
14. POWER LINES
e. If the product has been dropped or the cabinet
has been damaged.
f. When the product exhibits a distinct change in
performance - this indicates a need for service.
22. HEAT
An outside antenna system should not be located
in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall
into such power lines or circuits. When installing
an outside antenna system, extreme care should
be taken to keep from touching such power lines
or circuits as contact with them might be fatal.
15. OVERLOADING
The product should be situated away from heat
sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that
produce heat.
Do not overload wall outlets and extension cords
as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
23. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV
system installer's attention to Article 820-40 of the
NEC that provides guidelines for proper
grounding and, in particular, specifies that the
cable ground shall be connected to the grounding
system of the building, as close to the point of
cable entry as practical.
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short out parts that could result in
fire or electric shock. Never spill or spray any type
of liquid on the product.
17. SERVICING
24. NONUSE PERIODS
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
The power cord of the appliance should be
unplugged from the outlet when left unused for a
long period of time.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 4
Dear Customer:
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your
musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement
your equipment offers. This manufacturer and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of your equipment by playing it at a
safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion and, most importantly, without affecting your sensitive hearing. Sound can be
deceiving. Over time your hearing “comfort level” adapts to higher volumes of sound. So what
sounds “normal” can actually be loud and harmful to your hearing. Guard against this by
setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without
distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future. After
all, we want you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often undetectable until it is too late, this manufacturer and
the Electronic Industries Association’s Consumer Electronics Group recommend you avoid
prolonged exposure to excessive noise. This list of sound levels is included for your protection.
Decibel
Level
Example
30
40
50
60
70
80
Quiet library, soft whispers
Living room, refrigerator, bedroom away from traffic
Light traffic, normal conversation, quiet office
Air conditioner at 20 feet, sewing machine
Vacuum cleaner, hair dryer, noisy restaurant
Average city traffic, garbage disposals, alarm clock at two feet
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE:
90
Subway, motorcycle, truck traffic, lawn mower
Garbage truck, chain saw, pneumatic drill
Rock band concert in front of speakers, thunderclap
Gunshot blast, jet engine
100
120
140
180
Rocket launching pad
Information courtesy of the Deafness Research Foundation.
EIA
EST. 1924
We
WantYou
LISTENING
ForALifetime
4
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 5
LOCATION OF CONTROLS
1
2 3 4 5 6 7 8 9 1011 12 1314 1516 17 18 19
20 212223 24 25 26 27
1. POWER OFF Button
2. PHONES (Headphones) Jack
3. RECALL Button
15. VOLUME – Button
16. TIMER Button
17. VOLUME + Button
18. SLEEP Button
4. WAKE 1 Button
5. RADIO SET Button
6. RESET Button
7. TIMER Switch (Rear of Unit)
8. WAKE 2 Button
19. RADIO ON/BAND Button
20. TUNE/SKIP
21. PLAY/PAUSE (
/
Buttons
) Button
22. AC Cord (Rear of Unit)
9. SNOOZE Button
23. STOP ( ) Button
I
10. REV (Reverse) Button
11. OPEN/CLOSE Button
12. SET Button
13. FM RADIO (STEREO/MONO)
Switch (Rear of Unit)
24. Battery Compartment (Bottom
of Unit)
25. WAKE TRACK Button
26. REPEAT/Random Button
27. FM Antenna Wire (Rear of Unit)
14. FF (Fast Forward) Button
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 6
INSTALLATION
Unravel the AC cord and connect it to a
conveniently located AC outlet having 120V
and 60Hz only. The Clock Display will
illuminate and “12:00” will blink in the window.
NOTE: If the AC plug does not fit into a
nonpolarized outlet, do not file or cut the wide
blade.
If the AC cord is disconnected or if there is a
power failure, this electronic clock is designed
to continue operating internally (without showing the time on the Clock Display)
with a 9 volt battery (not included). To install the battery, connect the battery to
the terminals of the battery snap inside the compartment (use of an alkaline
battery is recommended).
Be sure to check the condition of the battery periodically by disconnecting the AC
cord and connecting it again two or three minutes
later. The preset times should continue operating. If
the present time does not appear, it indicates the
battery is dead or not connected properly. The 9 volt
battery will keep the internal times accurately for
approximately 30 minutes. If the power is restored
after 30 minutes, the times may need to be reset.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the
battery compartment. Reversed batteries may cause damage to the device.
3. If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.
4. Do not try to recharge batteries not intended to be recharged; they can overheat and
rupture. (Follow battery manufacturer’s directions.)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 7
OPERATION
TO SET OR RESET THE ACTUAL TIME
1
2
1
2
Press the REV ❶ or FF ❷ button to set
the time. Press the SET button ❸ three
times to exit the Clock Set mode.
Press the SET button once; “ ” will
appear in the display.
TO SET THE COUNTDOWN TIMER
The Countdown Timer will allow you to set a countdown time in minutes and
seconds and then beep when the time has elapsed.
1
2
3
2
4
Slide the TIMER switch ❶ on the rear Press the REV ❶ or FF ❷ button to set
of the unit to the COUNTDOWN the desired Countdown time, in minutes
position. Press the TIMER button ❷; and seconds. Press the TIMER button
❸ again; TIMER will appear in the
TIMER will blink and “1:00”, indicating
1 minute and 00 seconds, will appear display and the timer will countdown the
in the display.
preset time, then beep. Press the
TIMER button ❹ to turn off the beeping.
NOTE: The maximum Countdown time is 29 minutes, 59 seconds.
TO CANCEL THE COUNTDOWN TIMER
While the Countdown timer is counting down, simply press the TIMER button
again to cancel.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 8
OPERATION (CONTINUED)
TO SET THE NAP TIMER
The NAP Timer will allow you to set a NAP time in hours and minutes and then
beep when the time has elapsed.
1
2
3
2
4
Slide the TIMER switch ❶ on the rear Press the REV ❶ or FF ❷ button to set
of the unit to the NAP position. Press the desired NAP time, in hours and
the TIMER button ❷; TIMER will blink minutes. Press the TIMER button ❸
and “:20”, indicating 20 minutes, will again; TIMER and the Clock will appear
appear in the display.
in the display. When the desired NAP
time has elapsed, the unit will beep.
Press the TIMER button ❹ to turn off the
beep.
TO CANCEL THE NAP TIMER
While the countdown timer is counting down, slide the TIMER switch to the
COUNTDOWN position to cancel.
NOTES:
•
•
•
To check the NAP Timer time remaining, press the TIMER button; the NAP
Timer timer will appear briefly.
After pressing the SET or TIMER button, another button must be pressed
within five seconds, or the display will revert to the Clock mode.
The maximum NAP time is 2 hours.
HEADPHONES JACK:
For private listening, insert headphones into this jack. The speakers will be
disconnected when the headphones are plugged in.
BACK LIGHT
The back light in the display will light when radio or CD are playing. To light when
the unit is off, press any button; the back light will then come on for 10 seconds.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 9
OPERATION (CONTINUED)
TO LISTEN TO THE RADIO
1
2
1
1
2
Press the RADIO ON/BAND button ❶
once to turn the unit on and select
radio. Repeatedly press to select the
desired band (AM, FM). Slide the FM
RADIO switch ❷ on the rear of the unit
to the STEREO or MONO position as
desired. Sound present in Stereo
broadcasts can be reduced by sliding
this switch to the MONO position.
Tune a station by pressing the
TUNE/SKIP ❶ or ❷ button.
Press and hold the TUNE/SKIP
or ❷ button and the unit will scan
❶
and stop on the next strong station.
SETTING RADIO PRESETS
(TOTAL 10 PRESETS FOR AM/FM)
3
1
2
1
1
2
1
Adjust the volume using the VOLUME
+/– buttons ❶.
Press the POWER OFF button ❷ to
turn the unit off.
Tune a station as described in step 2
above, then press the RADIO SET
button ❶ once; the MEMO indicator
will blink. Press the RECALL button ❷
to select a radio preset number, then
press the RADIO SET button ❶ again
to confirm and the radio preset will be
set. To set the alarm station (“AL” will
appear), see page 14.
Antennas
FM: Extend the FM Antenna wire for better FM reception.
AM: Turn the unit for better AM reception.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 10
OPERATION (CONTINUED)
TO RECALL RADIO PRESETS
TO CHANGE A RADIO PRESET
1
1
2
1
To recall a Radio Preset, press the To change a Radio Preset, simply
RECALL button repeatedly until the tune a radio station as described on
desired Radio Preset appears in the the previous page, then press the
display.
RADIO SET button ❶; “MEMO” will
blink in the display. Repeatedly press
the RECALL button ❷ until the desired
Radio Preset appears in the display,
then press the RADIO SET button ❶
again to memorize.
NOTE: Once a radio frequency is selected, the display will revert to the time
display after 10 seconds.
TO INSERT A CD
TO REMOVE A CD
1
1
2
1
Make sure the CD has stopped and
open the CD compartment door by
pressing the OPEN/CLOSE button.
Hold the edge of the CD and pick it
up.
Press the PLAY/PAUSE (
) button ❶
to turn the unit on. Open the CD
compartment door by pressing the
OPEN/CLOSE button ❷. Gently press a
disc, label side up, onto the spindle and
press the OPEN/CLOSE button ❷ again
to close the CD compartment door.
IMPORTANT: The power must be on to open and close the CD Compartment door.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 11
OPERATION (CONTINUED)
TO PLAY A CD
1
2
Press the PLAY/PAUSE button to turn
the unit on and insert a CD as
described on the previous page; the
total number of tracks will appear in
the display.
Press the PLAY/PAUSE (
to start playback. TO PAUSE
PLAYBACK, press the PLAY/PAUSE
) button
(
) button again; “TRACK” will blink
in the display. Press again to resume
playback.
3
4
1
1
1
2
2
To skip forward or backward through the
tracks on the disc, press the TUNE/SKIP
Adjust the volume using the VOLUME
+/– buttons ❶ as desired. When the
disc is through playing, it will stop.
Press the STOP (I) button ❷ to stop
the disc before it is finished.
❶
or
❷ button. To search
forward or backward through the musical
passage on the disc, press and hold the
TUNE/SKIP
❶ or
❷ button.
FAQS: Do I need an adapter to play 3” singles?
No, simply insert the 3” single into the groove.
What is the maximum time for a CD in this unit?
The maximum time is 74 minutes.
NOTES:
• If a disc is inserted incorrectly, dirty, damaged or not present at all, the track
display will show “00”.
• To remove the CD, press the OPEN/CLOSE button and remove the CD.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 12
OPERATION (CONTINUED)
TO REPEATEDLY PLAY BACK ONE TRACK
1
2
2
1
3
4
Press the PLAY/PAUSE (
) button Press the TUNE/SKIP
❶ or
❷ button to select a track. Press the
PLAY/PAUSE ( ) button ❸ to start
❶ to turn the unit on and insert a CD
as described on page 10. Press the
REPEAT/Random button ❷ once;
“REP” will blink in the display.
playback and the unit will play the
same track over and over until the
STOP ( ) button ❹ is pressed.
TO REPEATEDLY PLAY BACK ALL TRACKS ON A CD
1
2
2
1
1
2
Press the PLAY/PAUSE (
) button
Press the PLAY/PAUSE (
) button
❶ to turn the unit on and insert a CD
as described on page 10. Press the
REPEAT/Random button ❷ twice;
“REP” will appear in the display.
❶ to start playback and the unit will
then play all the tracks on the CD over
and over until the STOP ( ) button ❷
is pressed.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 13
OPERATION (CONTINUED)
TO RANDOMLY PLAY BACK TRACKS ON A CD
1
2
2
1
Press the PLAY/PAUSE (
) button
Press the PLAY/PAUSE (
) button
❶ to turn the unit on and insert a CD
as described on page 10. Press the
REPEAT/Random button ❷ three
times; “REP RAN” will appear in the
display.
to begin playback. The unit will play all
the tracks in random order. When all
the tracks have been played, the unit
will stop.
TO SET OR RESET THE ALARM TIME(S)
2
1
1
2
Press the REV ❶ or FF ❷ button to set
the desired alarm time. Press the SET
button ❸ until the WAKE indicator
disappears from the display to set Alarm
1 or 2.
Press the SET button twice to set
Alarm 1, or three times to set Alarm 2;
“WAKE1” or “WAKE2” will appear in
the display.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 14
OPERATION (CONTINUED)
TO SET THE ALARM TO WAKE TO RADIO
1
2
2
1
Set the alarm time as previously Tune a station and then press the
instructed. Press the VOLUME +/- RADIO SET button ❶. Press the
buttons to set a desired wake up
volume.
RECALL button ❷ repeatedly until
“AL” appears in the display. Press the
RADIO SET button ❶ again to confirm
and the alarm radio preset will be set.
This is the station the unit will turn on
to when the alarm time matches the
actual time.
3
4
1
2
Press the desired WAKE button
To shut the alarm off, press the
POWER OFF button ❶ once and the
alarm time will be reset for the next
day.
The alarm can be temporarily turned
off manually by pressing the
SNOOZE button ❷; the alarm will turn
back on automatically nine minutes
later. It can be repeated endlessly.
1
2
(WAKE 1 or WAKE 2) until “ ” or “
”
appears in the display. The alarm is
now set to wake to radio and when the
alarm time matches the actual time,
the unit will turn on to the preset
station.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 15
OPERATION (CONTINUED)
TO SET THE ALARM TO WAKE TO CD
1
2
2
3
To set the Wake Track the unit will start
playing when the alarm time matches
the actual time, press and hold the
WAKE TRACK button ❶, then press the
Set the alarm time as previously
instructed. Press the VOLUME +/-
buttons to set a desired wake up
volume.
TUNE/SKIP
select the track.
NOTES:
❷ or
❸ button to
•
The unit will automatically be in the
Repeat All mode.
•
If you cannot select the Wake Track,
press the POWER OFF button or the
RADIO ON/BAND button. After doing
so, you can now press the WAKE
TRACK button as desired.
3
4
1
2
Press the desired WAKE button
(WAKE 1 or WAKE 2) until “❶” or “❷”
appears in the display. The alarm is
now set to wake to CD and when the
alarm time matches the actual time,
the unit will play the preset track,
followed by the remaining tracks on
the CD.
To shut the alarm off, press the
POWER OFF button ❶ once and the
alarm time will be reset for the next
day.
The alarm can be temporarily turned
off manually by pressing the
SNOOZE button ❷; the alarm will turn
back on automatically nine minutes
later. It can be repeated endlessly.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 16
OPERATION (CONTINUED)
TO SET THE ALARM TO WAKE TO BUZZER
1
2
Set the alarm time as previously Press the desired WAKE button
instructed. Press the VOLUME +/-
(WAKE 1 or WAKE 2) until “ ” or “
”
buttons to set a desired wake up
volume.
appears in the display. The alarm is
now set to wake to buzzer and when
the alarm time matches the actual
time, the unit buzzer will sound.
3
1
2
To shut the alarm off, press the
POWER OFF button ❶ once and the
alarm time will be reset for the next
day.
The alarm can be temporarily turned
off manually by pressing the
SNOOZE button ❷; the alarm will turn
back on automatically nine minutes
later. It can be repeated endlessly.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 17
OPERATION (CONTINUED)
TO CANCEL THE ALARM
1
2
2
2
To cancel the alarm so it does not
sound when the alarm time is
reached, press the RESET button ❶,
followed by the desired WAKE 1 or
WAKE 2 button ❷.
The Alarm indicator will disappear, but
the alarm time will remain in memory.
To activate, press the desired WAKE
1 or WAKE 2 button again.
TO USE THE SNOOZE FEATURE
1
The alarm can be temporarily turned
off manually by pressing the
SNOOZE button; the alarm will turn
back on automatically nine minutes
later. It can be repeated endlessly.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 18
OPERATION (CONTINUED)
TO ACTIVATE THE SLEEP FUNCTION
1
2
2
1
Tune the desired radio station or insert To adjust the sleep time, while
a CD as previously instructed. Press pressing and holding the SLEEP
and hold the SLEEP button and “:59” button ❶, press the REV ❷ or FF ❸
will appear on the clock display, then
release the button.
button until the desired sleep time
appears in the display.
NOTE:
3
To check the sleep time, simply
press the SLEEP button at any time.
Release the SLEEP button. When the
sleep time has elapsed, the unit will
turn off.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT
OUR WEBSITE AT WWW.MEMCORPINC.COM
OR CONTACT CUSTOMER SERVICE AT 1-800-919-3647.
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN
CASE YOU NEED TO RETURN THIS PRODUCT TO YOUR PLACE OF
PURCHASE OR MEMOREX.
FOR PARTS AND ACCESSORIES, CONTACT FOX INT’L AT 1-800-321-6993.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 19
CARE AND MAINTENANCE
Caring for Compact Discs
•
Treat the compact disc carefully. Handle the
compact disc only by its edges. Never allow
your fingers to come in contact with the shiny,
unprinted side of the disc.
•
•
•
•
Do not attach adhesive tape, stickers, etc.
to the compact disc label.
Clean the compact disc periodically with a soft, lint-free, dry cloth. Never use
detergents or abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.
If a compact disc skips or gets stuck on a section of the compact disc, it is
probably dirty or damaged (scratched).
When cleaning the compact disc, wipe in straight lines from the center of the
compact disc to the outer edge of the compact disc. Never wipe in circular motions.
Z
•
This unit is designed to play only compact discs bearing the
identification logo as shown here. Other discs may not conform to
the CD standard and may not play properly.
•
•
Compact Discs should be stored in their cases after each use to
avoid damage.
Do not expose compact discs to direct sunlight, high humidity, high
temperatures, or dust, etc. Prolonged exposure or extreme temperatures can
warp the disc.
•
Do not stick or write anything on either side of the disc. Sharp writing
instruments, or the ink may damage the surface.
Cleaning the unit
•
•
•
To prevent fire or shock hazard, disconnect your unit from the AC power
source when cleaning.
The finish on your unit may be cleaned with a dust cloth and cared for as other
furniture. Use caution when cleaning and wiping the plastic parts.
Mild soap and a damp cloth may be used on the front panel.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 20
TROUBLESHOOTING GUIDE
If you experience a problem with this unit, check the chart below before
calling for service.
SYMPTOM
Unit will not
CAUSE
AC cord not
connected.
SOLUTION
Check AC cord
connection.
turn on.
Disc will not play.
CD compartment
not closed.
Close CD compartment
door.
Disc inserted
incorrectly.
Reinsert disc correctly.
Dirty or defective CD. Try another disc.
Moisture
Wipe disc with soft cloth.
condensation on disc.
VOLUME is set
to minimum.
Defective disc.
Dirty or defective
disc.
No sound.
Increase volume.
Try another disc.
Erratic playback.
Clean or replace disc.
Time reset to “12:00”. Battery connected
improperly, not con-
Check the battery.
nected or dead.
Clock not set.
Set the clock.
Alarm does not
turn on.
Desired WAKE button Press desired WAKE
was not pressed.
Clock is not set.
Alarm is not set.
button.
Set the clock.
Set the Alarm.
AM or FM, no sound. Power is not on.
Press the RADIO ON/BAND
button to turn the unit on.
Increase volume.
VOLUME is set
to minimum.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
MMG-CR2900.OM.QXD 9/9/02 9:22 AM Page 21
Memcorp, Inc.
Weston, Fl
Printed in Hong Kong
Download from Www.Somanuals.com. All Manuals Search And Download.
|