MT2024
User’s Guide
20" COLOR TV WITH
REMOTE CONTROL
Before operating this product,
please read these instructions completely.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
ATTENTION:
POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISES ET POUSSER JUSQU’AU
FOND.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (CONTINUED)
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to alert
CAUTION
the user to the presence of uninsulated
RISK OF ELECTRIC SHOCK
DO NOT OPEN
dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
(This Caution Marking is located at the rear enclosure of the unit.)
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Before using the unit, be sure to read all operating instructions carefully. Please note that these are general precautions and may
not pertain to your unit. For example, this unit may not have the capability to be connected to an outdoor antenna.
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the product is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the product and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.
6. ATTACHMENTS
Do not use attachments not recommended by the product's manufacturer as they may cause hazards.
7. WATER AND MOISTURE
Do not use this product near water–for example: near a bathtub, washbowl, kitchen sink or laundry tub; in a wet basement; or near a
swimming pool.
8. ACCESSORIES
Do not place this product on an unstable cart, stand, tripod, bracket or table. The product may fall, causing serious
injury and serious damage to the product. Use only with a cart, stand, tripod, bracket or table recommended by the
manufacturer or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and
should use a mounting accessory recommended by the manufacturer.
8A. An appliance and cart combination should be moved with care. Quick stops, excessive force and uneven surfaces
may cause the appliance and cart combination to overturn.
9. VENTILATION
Slots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure reliable operation
of the product and to protect it from overheating. These openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near
or over a radiator or heat source. This product should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer's instructions have been adhered to.
10. POWER SOURCES
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of
power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery
power, or other sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION
This product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit
into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
13. LIGHTNING
To protect your product from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with them might be fatal.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (CONTINUED)
15. OVERLOADING
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could
result in fire or electric shock. Never spill or spray
any type of liquid on the product.
17. OUTDOOR ANTENNA GROUNDING
ANTENNA
LEAD IN
WIRE
If an outside antenna is connected to the
product, be sure the antenna system is
grounded so as to provide some protection
GROUND
CLAMP
against voltage surges and built-up static
charges. Section 810 of the National Electric
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
Code, ANSI/NFPA 70, provides information with
respect to proper grounding of the mast and
supporting structure, grounding of the lead-in
ELECTRIC
SERVICE
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
EQUIPMENT
wire to an antenna discharge product, size of
grounding conductors, location of antenna
GROUND CLAMPS
discharge product, connection to grounding
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
electrodes and requirements for grounding
electrodes.
NEC - NATIONAL ELECTRICAL CODE
S2898A
18. SERVICING
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that
have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
20. SAFETY CHECK
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the
product is in proper operating condition.
21. WALL OR CEILING MOUNTING
The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. DAMAGE REQUIRING SERVICE
Unplug the product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered
by the operating instructions, as an adjustment of other controls may result in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been damaged.
f. When the product exhibits a distinct change in performance–this indicates a need for service.
23. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves or other products (including
amplifiers) that produce heat.
24. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the
point of cable entry as practical.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER SOURCE
Insert the AC plug (with the 2 blades) into a conveniently located AC outlet having
120V, 60Hz.
AC Outlet
NOTE: The AC plug supplied with the unit is polarized to help minimize the possibility
of electric shock. If the AC plug does not fit into a nonpolarized AC outlet, do not file
or cut the wide blade. It is the user’s responsibility to have an electrician replace the
obsolete outlet.
AC Plug
LOCATION OF CONTROLS
FRONT
1. Audio 1 IN/Video 1 IN/Headphone Jacks
(Side of Unit)
7. CHANNEL Up Button
8. Display
2. MENU Button
9. Remote Sensor
3. TV/AV Button
10.Power Indicator–Standby light red, Power On
light green
4. VOLUME Down Button
5. VOLUME Up Button
6. CHANNEL Down Button
11. Power Button
NOTE:
When setting the TV Menus, the Channel Up/Down buttons are used as Navigation Up/Down and the
Volume Up/Down buttons are used as Navigation Right/Left.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION OF CONTROLS (CONTINUED)
REAR
1
2
3
4
5
6
1. Video OUT Jack
2. Audio OUT Jacks
3. S-Video IN Jack
4. Video 2 IN Jack
5. Audio 2 IN Jacks
6. Antenna Jack
REMOTE
1. MENU Button
2. VOLUME Up/Down Buttons
3. RECALL Button
4. TV/AV Button
5. P. STD (Picture) Button
6. Power Button
7. CHANNEL Up/Down Buttons
8. Direct Channel Selection Buttons (0-9)
9. -/-- Button
10. MTS/SAP Button
11. MUTE Button
12. DISPLAY Button
13. EXIT Button
NOTE:
When setting the TV Menus, the Channel
Up/Down buttons are used as Navigation
Up/Down and the Volume Up/Down buttons
are used as Navigation Right/Left.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL
BATTERY INSTALLATION
1.
Remove the Battery Compartment cover by pushing in on the tab and
lifting the cover off.
2. Install two (2) “AA” batteries (not included), paying attention to the
polarity diagram in the Battery Compartment.
3. Replace the Battery Compartment cover.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated next to the battery compartment.
Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and Carbon-zinc) or old batteries with
fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery
manufacturer’s directions.)
EFFECTIVE DISTANCE OF THE REMOTE CONTROL TRANSMITTER
NOTES:
• When there is an obstacle
between the TV and the
transmitter, the transmitter may
not operate.
• When direct sunlight, an
incandescent lamp, fluorescent
lamp or any other strong light
shines on the Remote Sensor
of the TV, the remote operation
may be unstable.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ANTENNA CONNECTIONS
OUTDOOR VHF/UHF ANTENNA CONNECTION (ANTENNA NOT INCLUDED)
Follow the instructions for the type of antenna system you intend to use. If using Cable or satellite, see the next page.
Combination VHF/UHF
Antenna (Single 75 ohm cable
or 300 ohm twin-lead wire)
Combination VHF/UHF
Antenna (Separate VHF and
UHF 300 ohm twin-leads)
Separate VHF/UHF Antennas
Connect the 75 ohm cable from the VHF
antenna and the UHF antenna twin-lead
wire to a combiner (NOT SUPPLIED).
Attach the combiner to the antenna jack.
NOTE: If your VHF antenna has a twin-
lead wire, use a 300-75 ohm matching
Connect the 75 ohm cable from Connect the UHF twin-lead wire to a
combination VHF/UHF antenna to the combiner (NOT SUPPLIED). Connect
antenna jack.
the VHF twin-lead to a 300-75 ohm
matching transformer (NOT SUPPLIED).
OR
If your combination antenna has a 300 Attach the transformer to the combiner.
ohm twin-lead wire, use a 300-75 ohm Attach the combiner to the antenna jack.
matching transformer (NOT SUPPLIED).
transformer,
then
connect
the
transformer to the combiner.
CONNECTION USING THE SIDE AUDIO/VIDEO IN JACKS
The optimal use for the side A/V jacks are to connect an A/V component that is used only occasionally, such as a
camcorder or video game. Connect the Audio/Video output jacks of the external unit to the Audio 1 Input jacks and the
Video 1 Input jack.
To access the unit connected to
these jacks, press the TV/AV
button repeatedly until VIDEO 1
appears on the screen. To
resume normal TV viewing,
EXTERNAL SOURCE
(i.e. camcorder, video game)
simply press the TV/AV button
repeatedly until the TV channel
appears in the display.
AUDIO/VIDEO Cord
(Not Supplied)
FAQs:
My external unit has only 1 audio jack, but this unit has two Audio Input jacks, how do I connect it?
Simply connect it to the “L (Mono)” Audio Input jack, but the sound will be monaural.
How do I watch the external unit connected to the Audio/Video Input jacks?
Press the TV/AV button repeatedly until VIDEO 1 appears on the screen, then start the external source.
Are the cables included?
No, the cables are sold separately, visit your local electronics store.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE (CATV)/SATELLITE CONNECTIONS
This TV has an extended tuning range and can tune most cable channels without using a Cable TV converter box. Some
Cable TV companies offer “premium pay channels” in which the signal is scrambled. Descrambling these signals for normal
viewing requires the use of a descrambler device which is generally provided by the cable company.
FOR SUBSCRIBERS TO BASIC CABLE TV SERVICE
For basic cable service not requiring a converter/descrambler box,
connect the CATV 75 ohm coaxial cable to the VHF/UHF jack on the
rear of the TV.
FOR SUBSCRIBERS TO SCRAMBLED CABLE TV SERVICE OR SATELLITE
If you subscribe to a satellite service or a cable TV service which requires the use of a converter/descrambler box, connect
the incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm cable, connect the output of
the converter/descrambler or satellite box to the antenna jack on the TV. Follow the connections shown below. Set the
TV/VCR to the output channel of the converter/descrambler or satellite box (usually 3 or 4) and use the
converter/descrambler or satellite box to select channels.
FOR SUBSCRIBERS TO UNSCRAMBLED BASIC CABLE TV SERVICE WITH SCRAMBLED
PREMIUM CHANNELS
If you subscribe to a satellite service or a cable TV service in which basic channels are unscrambled and premium channels
require the use of a converter/descrambler box, you may wish to use a signal splitter and an A/B switch box (available from the
cable company or an electronic supply store). Follow the connections shown below. With the switch in the “B” position, you can
directly tune any nonscrambled channels on your TV. With the switch in the “A” position, tune your TV to the output of the
converter/descrambler box (usually channel 3 or 4) and use the converter/descrambler box to tune scrambled channels.
FAQ:
I connected my cable, but why can’t I get channels above 69?
Make sure the TV (VHF/UHF Channels)/CATV (Cable TV) option is set to CATV (Cable TV), see page 21. Also, make sure
your cable company broadcasts channels in the range you are searching.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION FROM AN EXTERNAL UNIT
CONNECTION USING COAXIAL CABLE:
Follow the instructions below to connect an external unit, such as a VCR, to your unit using a 75 ohm coaxial cable. (CABLES
NOT INCLUDED.)
VCR
INCOMING CATV CABLE
From VCR OUT jack
1. Connect the cable, satellite or incoming antenna to the VHF/UHF IN jack on the rear of the VCR.
2. Connect a 75 ohm coaxial cable from the VCR’s 75 ohm OUT jack to the ANT jack on the rear of the TV.
3. Press the TV/AV button until regular TV or CATV channel appears on the TV screen and press PLAY on the VCR to
watch a tape.
CONNECTION USING AUDIO/VIDEO CABLES:
Follow the instructions below to connect an external unit, such as a VCR or a DVD player, to your unit using Audio/Video
cables. (CABLES NOT INCLUDED.)
VCR or DVD player
INCOMING CATV
CABLE (VCR)
From VCR OUT jacks
AUDIO/VIDEO Cord
1. Connect the cable, satellite or incoming antenna to the VHF/UHF IN jack on the rear of the VCR or DVD player.
2. Connect the left and right audio cable from the VCR/DVD’s Audio OUT jacks to the TV’s left and right Audio 2 IN jacks.
Connect the VCR/DVD’s Video OUT jack to the TV’s VIDEO 2 IN jack.
3. Press the TV/AV button until VIDEO2 appears on the TV screen.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION FROM AN EXTERNAL UNIT (CONTINUED)
CONNECTION USING S-VIDEO CABLE:
Follow the instructions below to connect an S-VIDEO VCR/DVD to your television using an S-video cable. (CABLES NOT
INCLUDED.)
VCR/DVD
INCOMING CATV
CABLE (VCR)
From VCR OUT jacks
AUDIO Cord
To S-VIDEO IN jack
1. For VCR, connect the cable, satellite or incoming antenna to the ANT jack on the rear of the VCR.
2. Connect the left and right audio cable from the DVD/ VCR’s Audio OUT jacks to the TV’s left and right AUDIO 2 IN
jacks.
3. Connect the DVD/VCR’s S-VIDEO OUT jack to the TV’s S-VIDEO IN jack.
4. Press the TV/AV button until S-VHS appears on the TV screen.
CONNECTION TO AN EXTERNAL UNIT
CONNECTION USING THE AUDIO/VIDEO OUT JACKS:
Follow the instructions below to connect an external audio unit. This will output the sound from the TV into the external audio
unit’s speakers.
VIDEO CORD (not supplied)
VIDEO IN Jack
VIDEO OUT Jack
1. Connect the left and right audio cable from the Amplifier’s Audio IN jacks to this unit’s AUDIO OUT jacks.
2. If desired, connect an external unit’s Video IN jack to this unit’s Video OUT jack.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE MENUS
VIDEO SETUP MENU:
SETTING THE PICTURE
1
2
3
1
2
2
1
3
Hue
Hue
Press the MENU button 1 once; the Video menu will appear.
Press the CHANNEL Up 2 or Down 3 button until the desired
picture setting is selected (PICTURE, BRIGHTNESS,
COLOR, SHARPNESS, HUE).
NOTE: The HUE option is only available while there is input
signal to VIDEO 1, VIDEO 2 & SVHS mode.
Press the VOLUME Up 1 or Down 2 button to adjust the
setting.
When done, press the MENU button 3 once to return to the
Video menu.
3
4
3
1
2
1
2
Hue
Hue
Press the CHANNEL Up 1 or Down 2 button until COLOR
TEMP is selected.
Press the VOLUME Up 1 or Down 2 button to set the
desired color balance (COOL, NEUTRAL or WARM). When
done, press the MENU button 3 twice to exit the menus.
AUDIO SETUP MENU:
1
2
1
1
Audio
Audio
3
4
2
3
Volume
10
2
Volume
10
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Audio setting.
Press the CHANNEL Up 1 or Down 2 button until VOLUME
is selected; volume will be highlighted in red. Press the
VOLUME Up 3 or Down 4 button to set the desired volume.
NOTES:
• To exit the menus, press the EXIT button.
• Use the Volume Up/Down buttons to adjust the volume directly while in TV/AV mode.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE MENUS (CONTINUED)
TIMER SETUP MENU:
SETTING THE CLOCK
Timer
Timer
1
2
1
Clock
Time-On
01:13
- - : - -
1
- - : - -
0
Clock
Time-On
01:13
- - : - -
1
- - : - -
0
1
3
2
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
2
- - : - -
1
- - : - -
1
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Timer setting.
Press the CHANNEL Up 1 or Down 2 button until CLOCK
is selected; the hours will be highlighted in red.
NOTE: The clock is a 24 hour (military time) type clock.
Timer
Timer
3
4
2
Clock
Time-On
01:13
- - : - -
1
- - : - -
0
Clock
Time-On
01:13
- - : - -
1
- - : - -
0
1
2
1
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
3
- - : - -
1
- - : - -
1
3
Press the VOLUME Up 1 or Down 2 button to set the
current hour, then press the CHANNEL Down button 3; the
minutes will be highlighted in red.
Press the VOLUME Up 1 or Down 2 button to set the
current minute. When done, press the EXIT button 3 to exit
the menus.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE MENUS (CONTINUED)
SETTING THE ON TIMER
Timer
Timer
1
2
Clock
Time-On
01:13
- - : - -
1
- - : - -
0
1
Clock
Time-On
01:13
12 : - -
1
- - : - -
0
1
3
2
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
2
- - : - -
1
- - : - -
1
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Timer setting.
Press the CHANNEL Up 1 or Down 2 button until TIME ON
is selected; the hours will be highlighted in red.
Timer
Timer
3
4
Clock
Time-On
01:13
12 : - -
1
- - : - -
0
Clock
Time-On
01:13
12 : 30
1
- - : - -
0
2
2
1
1
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
3
- - : - -
1
- - : - -
1
Press the VOLUME Up 1 or Down 2 button to set the
desired On hour, then press the CHANNEL Down button 3;
the minutes will be highlighted in red.
Press the VOLUME Up 1 or Down 2 button to set the
desired On minute.
Timer
Timer
5
6
2
1
Clock
Time-On
01:13
12 : 30
5
- - : - -
0
Clock
Time-On
01:13
12 : 30
5
- - : - -
0
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
- - : - -
1
- - : - -
1
3
Press the CHANNEL Down button until CH. SELECT is
selected.
Press the VOLUME Up 1 or Down 2 button to set the
desired On Channel (the channel the unit will turn on to).
When done, press the EXIT button 3 to exit the menus.
NOTE:
•
When the actual time matches the “On time”, the unit will automatically turn on.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE MENUS (CONTINUED)
SETTING THE OFF TIMER
Timer
Timer
1
2
1
Clock
Time-On
01:13
- - : - -
1
- - : - -
0
Clock
Time-On
01:13
12 : 30
5
12 : - -
0
1
3
2
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
2
- - : - -
1
- - : - -
1
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Timer setting.
Press the CHANNEL Up 1 or Down 2 button until TIME
OFF is selected; the hours will be highlighted in red.
Timer
Timer
3
4
2
Clock
Time-On
01:13
12 : 30
5
12 :45
0
Clock
Time-On
01:13
12 : 30
5
12 :45
0
1
2
1
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
3
- - : - -
1
- - : - -
1
3
Press the VOLUME Up 1 or Down 2 button to set the
desired Off hour, then press the CHANNEL Down button 3;
the minutes will be highlighted in red.
Press the VOLUME Up 1 or Down 2 button to set the
desired Off minute. When done, press the EXIT button 3 to
exit the menus.
NOTE:
•
When the actual time matches the “Off time”, the unit will automatically turn off.
SETTING THE SLEEP TIMER
Timer
Timer
1
2
1
2
4
Clock
Time-On
01:13
12 : 30
5
12 : 45
10
1
Clock
Time-On
01:13
12 : 30
5
12 : 45
10
3
2
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
5
- - : - -
1
- - : - -
1
3
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Timer setting. Press the CHANNEL Up 4 or
Down 5 button until SLEEP TIME is selected.
Press the VOLUME Up 1 or Down 2 button to set the desired
Sleep Time. When done, press the EXIT button 3 to exit the
menus. The sleep timer will count down and when it reaches
0, the unit will turn off.
NOTE: For the Sleep Timer, you can select from 0-180. For
example, set to 10 for the unit to turn off automatically after 10
minutes; set to 180 or the unit to turn off automatically after
180 minutes.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE MENUS (CONTINUED)
SETTING THE REMIND TIMER
Timer
Timer
1
2
1
Clock
Time-On
01:13
- - : - -
1
- - : - -
0
Clock
Time-On
01:13
12 : 30
5
12 : 45
0
1
3
2
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
2
- - : - -
1
16 : - -
1
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Timer setting.
Press the CHANNEL Up 1 or Down 2 button until REMIND
TIME is selected; the hours will be highlighted in red.
Timer
Timer
3
4
Clock
Time-On
01:13
12 : 30
5
12 : 45
0
Clock
Time-On
01:13
12 : 30
5
12 : 45
0
2
2
1
1
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
3
16 : 30
1
16 : 30
1
Press the VOLUME Up 1 or Down 2 button to set the
desired Remind hour, then press the CHANNEL Down
button 3; the minutes will be highlighted in red.
Press the VOLUME Up 1 or Down 2 button to set the
desired Remind minute.
Timer
5
4
Clock
01:13
12 : 30
5
12 : 45
0
Time-On
Ch. Select
Time-Off
Sleep Time
Remind Time
Ch. Switch
3
2
1
- - : - -
7
Press the CHANNEL Down button 1, CH.SWITCH will be
highlighted in red. Press the VOLUME Up 2 or Down 3
button to set the desired channel which you want to switch
to when the actual time reaches the Remind Time. When
done, press the MENU button 4 repeatedly to exit the
menus.
NOTE:
•
When the actual time matches the “Remind time”, the TV will switch to the channel which you set. This is useful so that
you won't miss a favorite TV program while you are watching another program on a different channel.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE MENUS (CONTINUED)
SETUP MENU:
SETTING THE LANGUAGE
Setup
1
2
2
1
1
Language
Background
Black Stretch
VNR
English
On
On
4
3
2
5
On
Fade
Off
C. Caption
Demo Mode
CC1
3
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Setup setting. Press the CHANNEL Up 4 or
Down 5 button until LANGUAGE is selected.
Press the VOLUME Up 1 or Down 2 button to set the
desired Language (ENGLISH, FRENCH or SPANISH).
When done, press the EXIT button 3 to exit the menus.
SETTING THE BACKGROUND (TV/CATV MODE ONLY)
1
Setup
2
2
1
1
4
Language
Background
Black Stretch
VNR
English
On
On
3
2
5
On
Fade
Off
C. Caption
Demo Mode
CC1
3
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Setup setting. Press the CHANNEL Up 4 or
Down 5 button until BACKGROUND is selected.
Press the VOLUME Up 1 or Down 2 button to turn the
Background ON (the background will be blue if no signal is
received) or OFF. When done, press the EXIT button 3 to
exit the menus.
SETTING THE BLACK STRETCH
Setup
1
2
2
1
1
4
Language
Background
Black Stretch
VNR
English
On
On
3
2
5
On
Fade
Off
C. Caption
Demo Mode
CC1
3
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Setup setting. Press the CHANNEL Up 4 or
Down 5 button until BLACK STRETCH is selected.
Press the VOLUME Up 1 or Down 2 button to turn the
Background ON (the contrast range will automatically be
increased) or OFF. When done, press the EXIT button 3 to
exit the menus.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE MENUS (CONTINUED)
SETTING THE VNR (VIDEO NOISE REDUCTION)
Setup
1
2
2
1
1
4
Language
Background
Black Stretch
VNR
English
On
On
3
2
5
On
Fade
Off
C. Caption
Demo Mode
CC1
3
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Setup setting. Press the CHANNEL Up 4 or
Down 5 button until VNR is selected.
Press the VOLUME Up 1 or Down 2 button to turn the VNR
ON (this will allow the picture tube to warm up and gently
turn on, thus increasing the life of the picture tube) or OFF.
When done, press the EXIT button 3 to exit the menus.
SETTING THE FADE
1
Setup
2
2
1
1
4
Language
Background
Black Stretch
VNR
English
On
On
3
2
5
On
Fade
Off
C. Caption
Demo Mode
CC1
3
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Setup setting. Press the CHANNEL Up 4 or
Down 5 button until FADE is selected.
Press the VOLUME Up 1 or Down 2 button to turn the
Fade ON (While the Fade function is on, the picture will
fade in when the TV is turned on and fade out when it is
turned off.) or OFF. When done, press the EXIT button 3 to
exit the menus.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE MENUS (CONTINUED)
SETTING THE CLOSED CAPTIONS
Setup
1
2
2
1
Language
Background
Black Stretch
VNR
English
On
On
1
4
3
2
5
On
Fade
Off
C. Caption
Demo Mode
CC1
3
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Setup setting. Press the CHANNEL Up 4 or
Down 5 button until C. CAPTION is selected.
Press the VOLUME Up 1 or Down 2 button to turn Closed
Captions off or on and select a mode (see page 31 for
details). When done, press the EXIT button 3 to exit the
menus.
SETTING THE TV TO DEMO MODE
Setup
1
2
Language
Background
Black Stretch
VNR
English
On
On
1
4
3
2
5
On
Fade
Off
C. Caption
Demo Mode
CC1
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Setup setting. Press the CHANNEL Up 4 or
Down 5 button until DEMO MODE is selected.
Press the VOLUME Up button to activate the Demo mode;
the unit will then enter the Demo mode and the screen will
show various features.
3
To stop Demo mode, press the EXIT button.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE MENUS (CONTINUED)
CHANNEL SETUP MENU:
SETTING THE CHANNEL SYSTEM
Channel
1
2
2
1
1
Channel System Auto
4
Antenna
Skip
Current Ch.
Fine
CATV
Off
13
3
2
5
Auto Program
3
Press the MENU button 1 once; the Video menu will appear.
Press the VOLUME Up 2 or Down 3 button to select the
Channel Setting. Press the CHANNEL Up 4 or Down 5
button until CHANNEL SYSTEM is selected.
Press the VOLUME Up 1 or Down 2 button to set the desired
Channel System (AUTO, NTSC or NTSC443). When done,
press the EXIT button 3 to exit the menus.
NOTE: In the USA, the system is NTSC.
SETTING THE FINE TUNING
Channel
1
2
1
4
Channel System Auto
Antenna
Skip
Current Ch.
Fine
CATV
Off
13
3
2
2
1
5
Auto Program
While in the TV mode, press the MENU button 1 once; the
Video menu will appear. Press the VOLUME Up 2 or Down
3 button to select the Channel Setting. Press the
CHANNEL Up 4 or Down 5 button until CURRENT CH. is
selected.
Press the VOLUME Up 1 or Down 2 button to select a
desired channel to fine tune.
Channel
3
4
2
1
1
Channel System Auto
Antenna
Skip
CATV
Off
3
2
Current Ch.
Fine
13
Auto Program
3
Press the CHANNEL Up 1 or Down 2 button until FINE is
selected, then press the VOLUME Up button 3.
Fine tune the channel using the VOLUME Up 1 or Down 2
button. When done, press the EXIT button 3 to exit the
menus.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE MENUS (CONTINUED)
SETTING CHANNELS INTO MEMORY
This unit is equipped with a channel memory feature which allows channels to skip up or down to the next channels set into
memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the unit’s memory. In
addition to normal VHF/UHF channels, this unit can receive up to 125 Cable TV channels.
1
2
Channel
1
4
Channel System Auto
2
3
Antenna
Skip
CATV
Off
1
2
5
Current Ch.
Fine
13
Auto Program
While in the TV mode, press the MENU button 1 once; the
Video menu will appear. Press the VOLUME Up 2 or Down
3 button to select the Channel Setting. Press the
CHANNEL Up 4 or Down 5 button until ANTENNA is
selected.
Press the VOLUME Up 1 or Down 2 button to select TV
(VHF/UHF Channels) or CATV (Cable TV).
Channel
3
4
1
Channel System Auto
1
Antenna
Skip
CATV
Off
2
Current Ch.
Fine
13
Auto Program
2
Press the CHANNEL Up 1 or Down 2 button until AUTO
PROGRAM is selected.
Press the VOLUME Up button 1 to start Auto
Programming and the unit will automatically cycle through
all the channels and store active channels into memory.
When finished, press the EXIT button 2 to exit the menu
settings.
FAQs:
How many channels will I actually receive?
The actual number of channels that can be received depends on how many channels your cable or satellite company, or
local area, provides. Contact your company to determine the number of channels in your area.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE MENUS (CONTINUED)
ADDING AND DELETING CHANNELS
After setting channels into memory, you can add or delete channels as follows:
Channel
1
2
1
Channel System Auto
4
Antenna
Skip
Current Ch.
Fine
CATV
Off
13
2
3
1
2
5
Auto Program
While in the TV mode, press the MENU button 1 once; the
Video menu will appear. Press the VOLUME Up 2 or Down
3 button to select the Channel Setting. Press the
CHANNEL Up 4 or Down 5 button until CURRENT CH. is
selected.
Press the VOLUME Up 1 or Down 2 button to select a
desired channel to add or delete.
Channel
3
4
2
1
Channel System Auto
1
Antenna
Skip
Current Ch.
Fine
CATV
Off
13
2
Auto Program
3
Press the CHANNEL Up 1 or Down 2 button until SKIP is
selected.
Press the VOLUME Up 1 or Down 2 button to turn Skip
feature ON (to skip the channel) or OFF (to memorize the
channel). When done, press the EXIT button 3 to exit the
menus.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE MENUS (CONTINUED)
CALENDAR SETUP MENU:
Calendar
2005 6
Calendar
2005 6
1
2
4
1
1
1
3
3
2
2
s
m
t
w
1
8
t
f
s
s
m
t
w
1
8
t
f
s
1
2
9
3
4
2
9
3
4
5
6
7
10 11
5
6
7
10 11
12 13 14 15 16 17 18
19 20 21 22 23 24 25
26 27 28 29 30
12 13 14 15 16 17 18
19 20 21 22 23 24 25
26 27 28 29 30
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Calendar setting.
Press the CHANNEL Down button 1 until the year is
selected. Press the VOLUME Up 2 or Down 3 button to set
the year, then press the CHANNEL Down button 1; the
month will be highlighted.
Calendar
Calendar
3
4
2
1
2005 6
1
2005 6 1
2
1
s
m
t
w
1
8
t
f
s
s
m
t
w
1
8
t
f
s
3
2
9
3
4
2
9
3
4
5
6
7
10 11
5
6
7
10 11
12 13 14 15 16 17 18
19 20 21 22 23 24 25
26 27 28 29 30
12 13 14 15 16 17 18
19 20 21 22 23 24 25
26 27 28 29 30
3
Press the VOLUME Up 1 or Down 2 button to set the
month, then press the CHANNEL Down button 3; the day
will be highlighted.
Press the VOLUME Up 1 or Down 2 button to set the day.
When done, press the EXIT button 3 to exit the menus.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TV PARENTAL CONTROL
V-Chip enables parents to prevent their children from watching inappropriate material on TV. V-Chip reads the ratings for
programming (except for news, sports, unedited movies on premium cable and Emergency System signals), then denies
access to programming if the program’s rating meets the limitations you select. In this case, the program will be blocked.
PARENTAL CONTROL SET-UP
1
2
1
4
Password
Password
Password
Password
3
2
5
----
----
You will be prompted to enter the password to enter this
menu. Enter the four digit password (The default password
is 1234) using the Direct Channel Selection/Number (0-9)
buttons.
Press the MENU button 1 once; the Video menu will
appear. Press the VOLUME Up 2 or Down 3 button to
select the Password. Press the CHANNEL Up 4 or Down
5 button until PASSWORD is highlighted in red.
3
4
Parental Lock
1
Parental Lock Off
Change Password
3
TV Rating
2
New Password
Confirm
----
----
MPAA Rating
Lock Menu
Change Password
TO CHANGE THE PASSWORD: After entering the menu,
press the CHANNEL Up 1 or Down 2 button until CHANGE
PASSWORD is selected, then press the VOLUME Up button
3.
Using the Direct Channel Selection/Number (0-9) buttons,
enter the desired password, then enter again to confirm
and make sure to write it down.
5
6
Parental Lock
Parental Lock
1
Parental Lock Off
TV Rating
MPAA Rating
Lock Menu
Parental Lock Off
TV Rating
MPAA Rating
Lock Menu
Change Password
2
1
2
Change Password
Press the CHANNEL Up 1 or Down 2 button until
PARENTAL LOCK is selected.
Press the VOLUME Up 1 or Down 2 button to turn
PARENTAL LOCK option On or Off.
NOTE: To exit the menus, press the Exit button.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TV PARENTAL CONTROL (CONTINUED)
TV RATING SET-UP
1
2
Parental Lock
1
Parental Lock Off
TV Rating
MPAA Rating
Lock Menu
4
3
2
Change Password
Enter the Parental Lock menu and turn on the V-chip option
as described on page 24 (steps 1 and 2).
Press the CHANNEL Up 1 or Down 2 button until TV
RATING is selected, then the VOLUME Up 3 or Down 4
button to select it.
4
TV Rating
3
TV Rating
4
1
3
Rating FV D L S
TV-Y > B
TV-Y7 B B
V
Rating FV D L S
TV-Y > B
TV-Y7 B B
V
1
2
3
2
TV-G
B
TV-G
B
TV-PG B
TV-14 B
TV-MA B
B B B
B B B
B
B
TV-PG B
TV-14 B
TV-MA B
B B B
B B B
B
B
B B B
B B B
Press the CHANNEL Up 1 or Down 2 button to select a
rating and then the VOLUME Up button 3 to BLOCK
(ratings at or above cannot be viewed) or UNBLOCK
(ratings at or under can be viewed).
You can also block some or all criteria for each level for
Fantasy Violence (FV), Sexual Dialogue (D), Language (L),
Sexual Situations (S) or Violence (V).
Using the CHANNEL Up 1 or Down 2 button, select the
desired criteria (to reach the criteria, cycle through the
columns using these buttons), then press the VOLUME Up
button 3 to turn the option On or Off.
When finished, press the Menu button 4 to return to the
Parental Lock menu or press the Exit button 5 to exit the
menus.
Y:
All ages
less than 14 years
Y7:
G:
Ages 7 and up
General Audience
Parental Guidance
Parental Guidance
old
MA:
Mature Audiences
Only
PG:
14:
"B" is Blocked and "U" is Unblocked.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TV PARENTAL CONTROL (CONTINUED)
MPAA RATING SET-UP
1
2
Parental Lock
1
Parental Lock Off
TV Rating
MPAA Rating
Lock Menu
4
3
2
Change Password
Enter the Parental Lock menu and turn on the V-chip option
as described on page 24 (steps 1 and 2).
Press the CHANNEL Up 1 or Down 2 button until MPAA
RATING is selected, then press the VOLUME Up 3 or
Down 4 button to select it.
3
4
1
MPAA RATING
1
G
PG
PG-13
R
NC-17
X
B
B
B
B
B
B
3
2
2
Press the CHANNEL Up 1 or Down 2 button to select a
rating and then the VOLUME Down button 3 to BLOCK
(ratings at or above cannot be viewed) or UNBLOCK
(ratings at or under can be viewed).
When finished, press the Menu button 1 to return to the
Parental Lock menu or press the Exit button 2 to exit the
menus.
G:
All ages
R:
Under 17 years old,
Parental Guidance
suggested
PG:
Parental Guidance
PG-13: Parental Guidance
less than 13 years NC17: 17 years old and
old
above
Adult only
X:
"B" is Blocked and "U" is Unblocked.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TV PARENTAL CONTROL (CONTINUED)
LOCK MENU
1
2
Parental Lock
1
Parental Lock Off
TV Rating
MPAA Rating
Lock Menu
2
Change Password
Enter the Parental Lock menu and turn on the V-chip option
as described on page 24 (steps 1 and 2).
Press the CHANNEL Up 1 or Down 2 button until LOCK
MENU is selected.
3
1
3
Lock
3
2
1
AV Lock
Program Lock
On
On
4
2
Press the VOLUME Up 1 or Down 2 to enter the Lock
menu. Press the CHANNEL Up 3 or Down 4 button to
select AV Lock or Program Lock. Press the VOLUME Up 1
or Down 2 to turn the option ON or OFF.
When finished, press the Menu button 1 to return to the
Parental Lock menu or press the Exit button 2 to exit the
menus.
NOTE: When AV Lock is ON, the Audio/Video connections will be locked (cannot be used).
For Program Lock, you must select the channel which needs to be locked before entering the Parental Lock menu in step 1.
When Program Lock is ON, the selected channel will be locked.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TV BASIC OPERATION
1
1
2
OPTIONS
TV:
If using a
VHF/UHF
antenna.
CATV: If using Cable
TV.
2
Change the Antenna option to select between TV or CATV.
Select TV if using VHF/UHF antenna, and select CATV if
using Cable TV (see page 21, steps 1 and 2).
Press the POWER button 1 on the remote, or front of the
unit, to turn on the unit; the POWER indicator will light
green. Press the TV/AV button 2 repeatedly to select the
TV mode.
3
4
1
2
2
1
3
4
For proper operation, before selecting channels, they must
be set into the unit’s Program memory, see page 21.
Press and release the CHANNEL Up 1 or Down 2 button.
The unit automatically stops at the next channel set into
memory.
Adjust the volume level by pressing the VOLUME Up 1 or
Down 2 button.
Direct Program Selection/Number buttons (0-9) 3
Use these buttons to select a channel.
• For Channels 1 through 9, press 1-9 3 as desired.
NOTES:
• For Channels 10 through 99, press -/-- button 4 once,
then enter the 2 digit channel number in order.
•
When ANTENNA option is set to TV, only channels up
to 69 can be chosen. When set to CATV, channels up
to 125 can be chosen.
• For Channels 100 through 125, press -/-- button 4 twice,
then enter the 3 digit channel number in order.
FAQs:
Why do I only receive 69 channels, when my cable goes much higher?
The TV/CATV option must be set to CATV when using cable, see step 2 above.
Why are some channels scrambled?
You must subscribe to these channels through your cable company.
HEADPHONE JACK (SIDE OF UNIT)
For private listening, connect 3.5mm (32 ohm) stereo headphones (not included) to this jack. The speakers are automatically disconnected
when the headphone plug is inserted in the jack.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
TV BASIC OPERATION (CONTINUED)
RECALL
DISPLAY
1
1
Press the RECALL button to switch between the present
channel and the last channel chosen.
Press the DISPLAY button once to display the current
information on the screen (Channel number or Video
mode). Press again to clear.
FAQ:
How do I watch the device connected to the side audio/video jacks?
Press the TV/AV button as described in the step at the top left of the next page.
MUTE
1
3
2
1
Press the Mute button to turn off the sound; the TV’s
sound will be silenced and “Mute” will appear on the
screen. The sound can be turned back on by pressing this
button again or one of the VOLUME Up 2 or Down 3
buttons; “Mute” will disappear form the screen.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
TV BASIC OPERATION (CONTINUED)
VOLUME Buttons
Set the sound as follows:
TV/AV
1
1
2
1
Press to select TV (CATV), VIDEO 1 (Side jacks), VIDEO
2 (Rear jacks) or SVHS (S-Video jack).
Press the VOLUME Up 1/Down 2 buttons to adjust the
sound level.
MTS/SAP
P.STD (Picture Standard)
1
1
Press to select between Auto Sap (Second Audio
Program), Stereo or Mono.
Press to select between the picture modes (Standard,
Vivid, Personal, Listen {select just to listen, not to watch},
or Movie).
NOTE: This function is for TV mode only.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
CLOSED CAPTIONS
Captions in other languages are transmitted on these
WHAT IS CLOSED CAPTIONING?
channels.
This television has the capability to decode and display
Closed Captioned television programs. Closed Captioning
will display text on the screen for hearing-impaired viewers or
it will translate and display text in another language.
TEXT: The Text Closed Caption Mode will usually fill the
screen with a programming schedule or other information.
Select between T1, T2, T3 or T4.
After selecting a Closed Caption Mode, it will stay in effect
until it is changed, even if the channel is changed. If the
Captions signal is lost due to a commercial or a break in the
signal, the Captions will reappear when the signal is received
again. If the channels are changed, the Captions will be
delayed approximately 10 seconds.
The Captions will appear in places on the screen where they
will least interfere with the picture, usually on the bottom of
the screen. News programs will usually show three-line
Closed Captions which scroll onto the screen. Most other
shows provide two or three lined Captions placed near the
character who is speaking so the viewer can follow the
dialogue.
CLOSED CAPTIONING WITH A VCR
Closed Captioned programs can be recorded and played
back on a VCR with the Closed Captioned text intact. The
Closed Captioned text will disappear during Cue (Fast
Forward Search), Review (Rewind Search) and Pause
modes or if the VCR tracking is not adjusted properly.
TO VIEW CLOSED CAPTIONS
Select the CC option in the menu to switch between normal
TV and the Closed Caption Modes (Captions and Full Screen
Text).
CC1: This Closed Caption Mode will display text on the Words in italics or underlined describe titles, words in foreign
screen in English or another language. Generally, Closed languages or words requiring emphasis. Words that are sung
Captions in English are transmitted on Captions 1.
usually appear enclosed by musical notes.
For television programs broadcasting with Closed Captions,
look in your TV guide for the Closed Captions symbol (CC).
CC2-4: These Closed Caption Modes will display text on the
screen in English or another language. Generally, Closed
NOTES:
• When selecting Closed Captions, the captioning will be delayed approximately 10 seconds.
• Misspellings or unusual characters may occasionally appear during Closed Captioning. This is normal with Closed
Captioning, especially with live programs. This is because during live programs, captions are also entered live. These
transmissions do not allow time for editing.
• When Captions are being displayed, on-screen displays, such as Mute, may not be seen or may interfere with Closed
Captions.
• Some cable systems and copy protection systems may interfere with the Closed Captioned signal.
• If using an indoor antenna or if TV reception is very poor, the Closed Caption Decoder may not appear or may appear with
strange characters or misspelled words. In this case, adjust the antenna for better reception or use an outdoor antenna.
FAQs:
When I press the RECALL or MUTE button, the captions do not appear, is this normal?
Yes, this is normal for this unit. Once the display information disappears, the captions will continue.
I entered the Captions mode, but no captions are appearing, why?
If no caption signal is received, no captions will appear, but the television will remain in the Caption mode.
Why is there a big black box on the screen?
Because you are in a Captions mode. Turn the captions off, or select a different Captions mode.
NOTE: To set the CLOSED CAPTIONS option, please see page 19.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
Check the following before requesting service.
SYMPTOM
POWER
POSSIBLE CAUSE
POSSIBLE SOLUTION
No power.
The AC power cord is not
connected.
Connect the AC power cord to
the AC outlet.
TV BROADCAST RECEPTION
TV station experiencing problems.
Try another channel.
Poor or no picture.
Picture control is not adjusted.
Possible local interference.
Check picture control adjustments.
Check for source of reception disturbance.
Antenna/CATV connector is not connected. Check CATV connection or VHF/UHF antenna.
TV station experiencing problems.
Try another channel.
Picture wobbles or drifts. Cable TV channel is scrambled.
Possible local interference.
A cable box needs to be used (if desired).
Check for source of reception disturbance.
CATV connected incorrectly or not connected. Check all CATV connections.
No CATV reception.
ANTENNA option set to TV.
Cable TV service interrupted.
Set ANTENNA option to CATV.
Contact your Cable TV company.
Set ANTENNA option to CATV.
Try another channel.
No reception above ch13. ANTENNA option set to TV.
TV station experiencing problems.
MUTE button is pressed.
Press MUTE button again.
Poor or no sound.
Possible local interference.
Check for source of reception disturbance.
Antenna/CATV connector is not connected. Check CATV connection or VHF/UHF antenna.
Volume is set to minimum.
TV station stopped broadcasting.
Sleep Timer is set.
Increase volume.
Tune to a new channel.
Turn off Sleep Timer function.
Reset or replace breaker.
Check CATV or VHF/UHF antenna.
Try another channel.
TV shuts off.
Home circuit breaker is blown.
TV Signal is weak.
Closed Captioning not
working.
TV station experiencing problems or
program tuned is not closed captioned.
Closed Captioning not turned on.
Turn on via the menu.
REMOTE CONTROL
The remote control is not
aimed at the sensor.
Aim the remote control at the
Remote Sensor.
Distance is too far or too much
light in the room.
Operate within 20 feet or reduce
the light in the room.
Remote control does
not operate.
There is an obstacle in the
path of the beam.
Clear the path of the beam.
The batteries are weak.
Replace the batteries.
Insert correctly.
The batteries are not inserted
correctly.
V-CHIP
Parental Control setting is turned off.
News or sports event being broadcast.
Turn Parental Control setting on.
Parental Control not
working properly.
Parental Control does not work with news or
sporting events.
Ratings not set.
Set ratings as desired.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
RECEPTION DISTURBANCES
Most types of television interference can be remedied by adjusting the height and position of the VHF/UHF antenna.
Outdoor antennas are recommended for best results if not using cable or a satellite. The most common types of television
interference are shown below. If one of these symptoms appear when the TV is connected to a Cable TV system, the
disturbance may be caused by the local cable company broadcast.
IGNITION:
Black spots or horizontal streaks may appear, picture may flutter or drift.
Usually caused by interference from automobile ignition systems, neon
lamps, electric drills and other electric appliances.
GHOSTS:
Ghosts are caused by the television signal following two paths. One is the
direct path and the other is reflected from tall buildings, hills or other
objects. Changing the direction or position of the antenna may improve the
reception.
SNOW:
If your receiver is located in the fringe area of a television station where the
signal is weak, your picture may be marred by the appearance of small
dots. When the signal is extremely weak, it may be necessary to install an
external antenna to improve the picture.
RADIO FREQUENCY INTERFERENCE:
This interference produces moving ripples or diagonal streaks, and in some
cases, causes loss of contrast in the picture.
PICTURE SIZE VARIATION:
A slight picture size variation is quite normal when you adjust the
CONTRAST or BRIGHT setting.
CARE AND MAINTENANCE
To prevent fire or shock hazard, disconnect your unit from the AC power source when cleaning. The finish on the unit may be
cleaned with a dust cloth and cared for as other furniture. Use caution when cleaning and wiping the plastic parts. Mild soap
and a soft, damp cloth may be used.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
TELEVISION
Picture Tube ...............................................................................................20” (Measured Diagonally)
Antenna Input Impedance..........................................................................VHF/UHF, 75 Ohm Coaxial
Input RCA Video ...........................................................................................................1Vp-p/75 Ohm
Input RCA Audio .....................................................................................................0.5Vrms/50K Ohm
Output RCA Video .........................................................................................................1Vp-p/75 Ohm
Output RCA Audio ....................................................................................................0.5Vrms/1K Ohm
GENERAL
Power Source ...............................................................................................................120V, 60Hz AC
Power Consumption .....................................................................................................................70 W
Dimensions................................................................................24.6 (W) x 18.9 (D) x 17.7 (H) inches
Weight ......................................................................................................................................59.4 lbs
Features and specifications are subject to change without notice.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT OUR WEBSITE AT
WWW.MEMOREXELECTRONICS.COM OR C(O9N5T4A)C6T6C0U-7ST1O0M0ER SERVICE AT
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN CASE YOU NEED TO RETURN
THIS PRODUCT TO YOUR PLACE OF PURCHASE OR MEMOREX.
FOR PARTS AND ACCESSORIES, CONTACT FOX INTERNATIONAL AT 1-800-321-6993.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Memcorp, Inc.
Weston, FL
Printed in Hong Kong
Download from Www.Somanuals.com. All Manuals Search And Download.
|