MT1091
9” Color Television
Owner’s Manual
POWER
Multi Function Remote�
On Screen Display
VOLUME
CHANNEL
R
®
As an ENERGY STAR Partner, MEMCORP has
®
determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
• On-screen graphics guide you through setup features and operations
• Automatic programming of channels allows easy selection of stations available in your
viewing area
• Sleep timer programs the TV to turn itself off at a preset time
• One day timer programs the TV to come on once at a preset time
• Weekly timer programs the TV to come on at a preset time every day
• 24-button infrared remote control allows remote operation
• VHF/UHF/CATV tuning allows reception of standard broadcasts or cable TV channels
SPECIFICATIONS
Power Input:
AC: 120V, 60Hz
DC: 12V
Power Consumption:
AC: 55Watts
DC: 36Watts
Chassis Construction:
Picture Tube:
Speaker:
Tuner:
Remote Control:
IC Solid State
9” (measured diagonally)
2.8 x 1.6 in. (70 x 40 mm) Oval, 8 ohms
181 Channel, Freq. Synthesized
Infrared, Direct Access
24 Key, 2 “AA” batteries
Receiving Channels:
VHF
2–13
UHF
14–69
CATV
Mid Band
14–22
Super Band
Hyper Band
Ultra Band
Sub Mid Band
Cabinet:
23–36
37–65
66–94, 100–125
1, 95–99
Monitor Style
Antenna Input Impedance:
75 ohm (VHF/UHF) Coaxial Input
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT AND FULLY INSERT.
– 2 –
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION OF CONTROLS
EXT.ANT.�
UHF/VHF
IN
DC－12V
VIDEO
AUDIO
POWER
Multi Function Remote�
On Screen Display
VOLUME
CHANNEL
R
7
6
5 4 3 2 1
@ ! 0 9 8
1 POWER SWITCH
7 EARPHONE JACK (
)
2 CHANNEL ▲ (UP) BUTTON
3 CHANNEL ▼ (DOWN) BUTTON
4 VOLUME ▲ (UP) BUTTON
5 VOLUME ▼ (DOWN) BUTTON
6 REMOTE CONTROL SENSOR
8 ANTENNA HOLDER
9 AUDIO IN (put) JACK
10 VIDEO IN (put) JACK
11 DC INPUT JACK
12 VHF/UHF EXT. ANT. JACK
– 3 –
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL
The REMOTE CONTROL unit requires two 1.5 volt “AA” size batteries. The BATTERY
COMPARTMENT is located on the back of the unit. To open, press down of the lid and
slide toward the bottom of the unit. Install the batteries exactly as shown by the diagram in
the compartment.
NOTE: If one or both of the batteries are reversed, the REMOTE CONTROL will not
operate and the unit may be damaged.
This REMOTE CONTROL unit uses an INFRARED WIRELESS CONTROL SYSTEM.
This means that the remote commands are sent out as invisible light. For best operation,
aim the REMOTE CONTROL unit directly at the REMOTE CONTROL SENSOR window
on the lower center front of the TV. Please note that furniture or other solid objects can
block the path of the infrared light. Dark walls might absorb the light.
Do not allow strong sunshine to fall on the TV set front panel as this may affect the opera-
tion of the remote control. In this case, tune the TV away from the light or darken the room
slightly.
POWER
Multi Function Remote
On Screen Display
VOLUME
CHANNEL
R
24 Feet
15˚ 15˚
POWER
TV/VIDEO
SLEEP
RECALL
MENU
MUTE
Q.REV.
CHANNEL
VOLUME
– 4 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
POWER Button
Press to turn the TV on or off.
TV/VIDEO Button
Pressing this button permits
the TV to be used as a
monitor to view program
sources such as a VCR,Video
Disc, ect. press again to
resume normal TV function.
Number Buttons
Press to select a channel. For
channels 1-9, press 0, then the
channel you want to watch. For
example, for channel 6, press 0,
6. For channels 100-125, press
the 100 button, then press the
last two digits of the channel
you want to watch .For
example, for channel 116, press
100, 1, 6. Note:Make sure you
press the second or third digit
of a channel within a few
POWER
TV/VIDEO
SLEEP
SLEEP Button
Press to start the sleep time or
to display the time left in a
sleep timer. See page 15 for
details.
seconds of pressing the first
digit. If you don't, you'll have to
start over.
RECALL
Q.REV.
RECALL Button
Press to display the channel
being viewed. Press again to
display the time. Press again
to remove the
– and + Buttons
Press to adjust or select
functions listed in on-screen
displays.
MENU
MUTE
on-screen display.
MENU Button
Press to call up the main menu
screen. Also, press to enter data
when going to the next step of
an operation.
Q.REV. (Quick Review)
Button
CHANNEL
Press to return to the previous
channel. For example, if you
were watching channel 2, then
use the Number buttons to
switch to channel 6, pressing
the Q.REV button will return
the TV to channel 2.
VOLUME
MUTE Button
Press once to eliminate sound.
Press again to hear sound.
VOLUME (Up/Down) Buttons
Press to raise or lower the
sound.
CHANNEL (Up/Down)
Buttons
Press to scroll up or down
through the channels.
– 5 –
Download from Www.Somanuals.com. All Manuals Search And Download.
ANTENNA CONNECTIONS
If you are using an indoor antenna (included) or an outdoor antenna (not included) follow
the instructions below that correspond to your antenna system. If you are using a cable
television service (CATV), refer to CATV connections.
Combination VHF/UHF Antenna (Single 75 ohm cable or 300 ohm twin-lead
wire)
Connect the 75 ohm cable from combina-
tion VHF/UHF antenna to the antenna jack.
75 ohm
OR
ANT
OR
If your combination antenna has a 300 ohm
twin-lead wire, use the 300-75 ohm match-
ing transformer (included)
Transformer
(included)
300 ohm
CATV CONNECTIONS
For subscribers to basic cable service.
For basic cable service without a converter/
descrambler box, connect the CATV 75
ohm coaxial cable directly to the antenna
jack on back of the unit.
ANT
Connecting an Internal Antenna
Your TV comes with an internal antenna.
Use it if you want to place the TV where
there is no outdoor connection.
Rod Antenna
(included)
Antenna Holder
1 Place the rod antenna (included) into the
antenna holder on the back of the TV
cabinet. Push it down until it locks in
place.
Antenna
Leads
2 Connect the antenna leads (flat prongs)
to the two screws on the transformer (in-
cluded).
3 Push the round terminal on the back of
the transformer into the EXT. ANT. jack
on the back of the TV.
Transformer
(included)
EXT.ANT.�
UHF/VHF
I
DC－12V
VIDEO
AUDIO
4 Extend and adjust the antenna.
– 6 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Some cable companies offer “premium pay” channels in which the signal is scrambled.
Descrambling these signals for normal viewing requires the use of a descrambler device
which is generally provided by the cable company.
The illustrations below show how to connect these types of converter/descrambler de-
vices with the TV’s VHF antenna jack.
You may need a two-set signal splitter (sometime called a “two-set coupler”) and an A/B
switch box from the cable installer or an electronic supply store. With the A/B switch in the
“B” position, you can then tune directly to any non-scrambled channels using your TV’s
tuning system or remote control. In the “A” position, you can tune your TV to the output
channel of the decoder (generally Channel 3/4) and use the cable company’s equipment
to tune scrambled channels. Since cable systems vary, you may wish to consult your local
cable company.
For subscribers to scrambled pay cable service
INCOMING
COAXIAL CABLE
To 75 ohm Coaxial
Jack On TV
Converter/Descrambler
POWER
Multi Function Remote�
On Screen Display
VOLUME
CHANNEL
R
To allow viewing of all channels through converter/descrambler. TV must be set to the
output channel of the converter/ descrambler (usually ch 3 or 4).
NOTE: If you subscribe to a cable service which requires you to use a converter/descrambler
box, follow the connections shown above.
If your basic cable channels are unscrambled and are using a converter/descrambler for
premium channels, follow the connections shown below.
For subscribers of unscrambled basic cable with a converter/descrambler box for viewing
premium channels.
To 75 ohm
Coaxial
Jack On TV
INCOMING
COAXIAL
CABLE
Converter/Descrambler
A
SPLITTER
A/B Switch
B
POWER
Multi Function Remote�
On Screen Display
VOLUME
CHANNEL
R
A—Allows viewing of scrambled channels through converter/descrambler box.
B—Allows full use of TV tuner and Remote Control.
NOTE: For other cable connections, consult your cable company.
– 7 –
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER SOURCE
You can connect the TV to a household outlet or to the cigarette lighter of your car.
AC Power
Connect the polarized AC cord plug to a 120V AC 60Hz household outlet.
NOTES
1. NEVER CONNECT THE AC LINE CORD PLUG TO OTHER THAN THE SPECIFIED
VOLTAGE.
USE THE ATTACHED POWER CORD ONLY.
2. IF THE POLARIZED AC CORD DOES NOT FIT INTO A NON-POLARIZED AC
OUTLET, DO NOT ATTEMPT TO FILE OR CUT THE WIDE BLADE.
Polarized AC Cord
Cigarette Lighter Power
1 Insert one end of the DC car cord (included) into the DC input jack on the back of the
TV.
2 Insert the other end of the DC car cord into the cigarette lighter in your car.
NOTES
The polarity of the DC Input jack is not like most others. Attaching a DC power cord of reverse
polarity will make the four-amp fuse blow. Therefore, use only the DC car cord included with
your TV for connection to the cigarette lighter of your car.
When using an external power source:
• It may be difficult to obtain good reception while the car is moving.
• It is recommended that you operate the TV with your car engine idling when very low
outside temperatures cause difficulty in starting the engine.
• Do not operate the TV when starting your car engine. Doing so may overload the engine.
• When you are finished watching TV, turn the power off and disconnect the DC car cord
from the cigarette lighter. If you don’t do this, you may run down your car’s battery.
• Do not operate your TV with a dirty cigarette lighter. Cigarette ash may cause the DC car
cord plug to become overheated.
– 8 –
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK USE GUIDE
If you’re already familiar with TV hookup and operation, just follow the quick steps below to
make some basic connections and adjustments before using your new TV.
a Place batteries in the remote control.
ton to select it. Press the + or – button
to highlight AIR/CABLE, then press the
MENU button until the input you have
connected to your TV (AIR for antenna
or CABLE for cable) appears to the right
of AIR/CABLE. Then use the + or – but-
ton to highlight EXIT, and press the
MENU button to exit. (See page 11 for
details).
(See page 4).
s Connect the TV to an antenna or cable.
(See page 6).
d Connect a power supply.
f Press the POWER button to turn the TV on.
g Press the MENU button to bring up the
main menu screen. Press the + or –
button to highlight LANGUAGE, then
press the MENU button until the on-
screen menu is in the language you want
it to be in. (See page 9).
j Go to page 11 and program channels.
k Use the CHANNEL (Up/Down) or Number
buttons to select a channel for viewing.
Use the VOLUME (Up/Down) buttons to
adjust the sound level.
h Use the + or – button to highlight CH
PROGRAM, then press the MENU but-
SELECTING A LANGUAGE
The menu screen that appears when you press the MENU button can be programmed to
appear in English, French, or Spanish. Follow the directions below to program the menu
screen to appear in a language other than the one that is now on-screen when you press
the MENU button.
a Press the MENU button to bring up the
d Press the MENU button until the menu
screen is in the language you want to
select.
menu-screen.
MENU SUN – – : – – AM
CLOCK SET
f Use the + or – button to highlight EXIT.
PROGRAM TIMER
PICTURE ADJUST
CH PROGRAM
LANGUAGE
MENU SUN – – : – – AM
DEMONSTRATION
EXIT
CLOCK SET
PROGRAM TIMER
PICTURE ADJUST
CH PROGRAM
LANGUAGE
[+] / [–] : MENU SELECT
[MENU] : ENTER
DEMONSTRATION
EXIT
s Use the + or – button to highlight LAN-
[+] / [–] : MENU SELECT
[MENU] : EXIT
GUAGE.
MENU SUN – – : – – AM
CLOCK SET
PROGRAM TIMER
PICTURE ADJUST
CH PROGRAM
LANGUAGE
g Press the MENU button to exit.
DEMONSTRATION
EXIT
[+] / [–] : MENU SELECT
[MENU] : ENTER
– 9 –
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE CLOCK
a Press the MENU button twice to bring
up the menu screen and select CLOCK
SET.
CLOCK SET
TUE 1 : 3 5 AM
EXIT
CLOCK SET
[MENU] : MOVE
[+] / [–] : ADJUST
SUN – – : – – AM
EXIT
j Press the MENU button to go to the next
[MENU] : MOVE
[+] / [–] : ADJUST
step.
k Use the + or – button to select AM or
s Use the + or – button to select the cor-
PM.
rect day of the week.
CLOCK SET
CLOCK SET
TUE 1 : 3 5 PM
EXIT
TUE – – : – – AM
EXIT
[MENU] : MOVE
[+] / [–] : ADJUST
[MENU] : MOVE
[+] / [–] : ADJUST
l Press the MENU button. EXIT will flash.
d Press the MENU button to go to the next
step.
; Press the + or – button to exit.
f Use the + or – button to select the cor-
NOTES
rect hour(s).
• To display the day and time at any time.
Press the RECALL button twice. To
remove the display, press the RECALL
button again.
CLOCK SET
TUE 1 : – – AM
EXIT
• To correct the day or time, follow step 1
to bring up the clock set menu. Then
press the MENU button until the section
of the display you want to correct is
flashing. Use the + or – button to cor-
rect the day or time. Finally, press the
MENU button until EXIT is flashing,
then press the + or – button to exit.
• You may have to reset the clock if there
is a power outage or if you unplug the
TV.
[MENU] : MOVE
[+] / [–] : ADJUST
g Press the MENU button to go to the next
step.
h Use the + or – button to select the cor-
rect minute(s).
– 10 –
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAMMING CHANNELS
With automatic programming, the TV automatically places every channel you receive in its
memory, allowing you to scan through those channels when you press the CHANNEL
(Up/Down) buttons. With manual programming, you tell the TV what channels you want to
scan through when you press the CHANNEL (Up/Down) buttons.
Automatic Programming
f Use the + or – button to highlight AUTO
a Press the MENU button to bring up the
SEARCH.
menu screen.
MENU
TUE 1:35PM
CH PROGRAM
CLOCK SET
AIR/CABLE
AUTO SEARCH
CH MEMORY
EXIT
CABLE
PROGRAM TIMER
PICTURE ADJUST
CH PROGRAM
LANGUAGE
DEMONSTRATION
EXIT
[+] / [–] : SELECT
[+] / [–] : MENU SELECT
[MENU] : START
[MENU] : ENTER
g Press the MENU button to select AUTO
SEARCH. The TV will flip through all of
its 125 channels, placing the ones you
receive in its memory. When it is fin-
ished, the channel program screen will
appear on-screen again.
s Use the + or – button to highlight CH
PROGRAM, then press the MENU but-
ton to select it.
CH PROGRAM
AIR/CABLE
AUTO SEARCH
CH MEMORY
EXIT
CABLE
h Use the + or – button to highlight EXIT.
CH PROGRAM
AIR/CABLE
AUTO SEARCH
CH MEMORY
EXIT
CABLE
[+] / [–] : SELECT
[MENU] : AIR/CABLE
d If you have a cable connected to the TV,
press the MENU button until CABLE
appears to the right of AIR/CABLE. If
you have an antenna connected to the
TV, press the MENU button until AIR
appears to the right of AIR/CABLE.
[+] / [–] : SELECT
[MENU] : EXIT
j Press the MENU button to exit.
CH PROGRAM
AIR/CABLE
AUTO SEARCH
CH MEMORY
EXIT
CABLE
NOTES
To stop automatic programing while it is
in progress, press the MENU button.
[+] / [–] : SELECT
[MENU] : AIR/CABLE
– 11 –
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDING/DELETING CHANNELS
Manual Programming
g Press the CHANNEL (Up or Down) but-
ton or Number buttons to select the
channel you want to add to or delete
from the TV’s memory.
a Press the MENU button to bring up the
menu screen.
MENU
TUE 1:35PM
CLOCK SET
PROGRAM TIMER
PICTURE ADJUST
CH PROGRAM
LANGUAGE
DEMONSTRATION
EXIT
h Press the + button to add the channel
(it will turn white). Or, press the – button
to delete the channel (it will turn red).
[+] / [–] : MENU SELECT
[MENU] : ENTER
s Use the + or – button to highlight CH
PROGRAM, then press the MENU but-
ton to select it.
j Follow steps 5 and 6 to add or delete
other channels.
CH PROGRAM
k Press the MENU button to return to the
AIR/CABLE
AUTO SEARCH
CH MEMORY
EXIT
CABLE
channel program screen.
l Press the MENU button to exit while
[+] / [–] : SELECT
[MENU] : AIR/CABLE
EXIT is highlighted.
d Use the + or – button to highlight CH
MEMORY.
CH PROGRAM
AIR/CABLE
AUTO SEARCH
CH MEMORY
EXIT
CABLE
[+] / [–] : SELECT
[MENU] : ENTER
NOTES
• If you don't program channels, you will
still receive channels when you press the
CHANNEL (Up) and (Down) buttons or
Number buttons. But you will also have
to scan through channel that have no
reception or very poor reception when
you press the CHANNEL (Up) and
(Down) buttons.
f Press the MENU button to select CH
MEMORY.
CH MEMORY
CABLE
10
• You may have to reprogram channels if
there is a power outage or if the TV is
unplugged.
[+]
[–]
: ADD
: DELETE
[MENU] : EXIT
– 12 –
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE TIMERS
You can program your TV to turn on a specific channel at a preset time once (one day
timer) or at the same time every day or every week (weekly timer). You also can program
your TV to turn itself off after a specified amount of time (sleep timer).
ONE DAY TIMER
One Day Timer
ON TIME
– –:– – AM – –:– – AM
OFF TIME
CH
10
a Press the MENU button to bring up the
menu screen.
EXIT
MENU
TUE 1:35PM
CLOCK SET
[MENU] : MOVE
[+] / [–] : ADJUST
PROGRAM TIMER
PICTURE ADJUST
CH PROGRAM
LANGUAGE
DEMONSTRATION
EXIT
h Use the + or – button to select the hour
you want the timer to come on, then
press the MENU button. Use the + or –
button to select the minute(s) you want
the timer to come on, then press the
MENU button. Use the + or – button to
select AM or PM, then press the MENU
button. The OFF TIME changes to ex-
actly three hours after the ON TIME. To
change the OFF TIME follow the same
steps you did to set the ON TIME.
[+] / [–] : MENU SELECT
[MENU] : ENTER
s Use the + or – button to highlight PRO-
GRAM TIMER, then press the MENU
button.
PROGRAM TIMER
ONE DAY OFF
WEEKLY
EXIT
OFF
j Use the CHANNEL (Up or Down) buttons,
+ or – buttons, or Number buttons to se-
lect the channel you want the TV to come
on, then press the MENU button.
[+] / [–] : SELECT
[MENU] : ENTER
ONE DAY TIMER
d While ONE DAY is highlighted, press the
MENU button. The OFF (or ON) to the
right of ONE DAY will flash.
ON TIME
1 : 00 PM
OFF TIME
2 : 00 PM
CH
22
EXIT
f Press the + or – button until ON appears
beside ONE DAY.
[MENU] : MOVE
[CH : ADJUST
/
]
PROGRAM TIMER
ONE DAY
WEEKLY
EXIT
ON
OFF
k While EXIT is blinking, press the + or –
button to exit.
NOTES
• To cancel a timer, follow steps 1
through 3. At step 4, use the + or –
button to turn the ON to OFF.
[+] / [–] : ON/OFF
[MENU] : ENTER
• The one day timer has priority when the
same time value is set for the ON TIME
field of both the one day timer and the
weekly timer.
g Press the MENU button to bring up the
one day timer screen.
– 13 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Weekly Timer
a Press the MENU button to bring up the
h Use the + or – button to select the hour
you want the timer to come on, then
press the MENU button. Use the + or –
button to select the minute(s) you want
the timer to come on, then press the
MENU button. Use the + or – button to
select AM or PM, then press the MENU
button. Follow the same steps to set the
time off.
menu screen.
MENU
TUE 1:35PM
CLOCK SET
PROGRAM TIMER
PICTURE ADJUST
CH PROGRAM
LANGUAGE
DEMONSTRATION
EXIT
[+] / [–] : MENU SELECT
[MENU] : ENTER
j Use the CHANNEL (Up or Down) but-
tons, + or – buttons, or Number buttons
to select the channel you want the TV
to come on, then press the MENU but-
ton.
s Use the + or – button to highlight PRO-
GRAM TIMER, then press the MENU
button.
PROGRAM TIMER
ONE DAY OFF
k Press the MENU button to select the
day(s) of the week you do not want the
TV to come on. Once that day is flash-
ing, use the + or – button to unselect
that day of the week (the TV will not
come on) signified in red or reselect that
day of the week (the TV will come on)
signified in white.
WEEKLY
EXIT
OFF
[+] / [–] : SELECT
[MENU] : ENTER
d Press the + or – button to select
WEEKLY, then press the MENU button.
The word OFF (or ON) to the right of
WEEKLY will flash.
WEEKLY TIMER
ON TIME OFF TIME
1 : 00 PM 2 : 00 PM
CH
22
f Press the + or – button until ON appears
beside WEEKLY.
SUN MON TUE WED THU FRI SAT
EXIT
PROGRAM TIMER
ONE DAY OFF
[MENU] : MOVE
WEEKLY
EXIT
ON
[+] / [–] : ADJUST
l While EXIT is blinking, press the + or –
button to exit.
[+] / [–] : ON / OFF
[MENU] : ENTER
g Press the MENU button to bring up the
weekly timer screen.
NOTES
• To cancel a timer, follow steps 1through
3. Then use the + or – button to turn
the ON to OFF.
• The timer will come on only on the days
that appear in white on the weekly timer
screen.
WEEKLY TIMER
ON TIME OFF TIME
– –:– – AM – –:– – AM
CH
10
SUN MON TUE WED THU FRI SAT
EXIT
[MENU] : MOVE
[+] / [–] : ADJUST
– 14 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Sleep Timer
a Press the SLEEP button to bring up the
s Press the SLEEP button until the desired
sleep time (10, 20, 30, 40, 50, 60, 70,
80 or 90 minutes) appears on-screen.
The timer will begin counting down to
zero, and the on-screen display will dis-
appear. When the timer reaches zero,
the TV will turn itself off.
sleep timer screen.
SLEEP 00
SLEEP 60
NOTES
• To check the time remaining for a sleep timer, press the SLEEP button. The
time remaining will appear on-screen.
• To cancel a sleep timer, follow step 1 to bring up the sleep timer screen.
Then press the SLEEP button until 00 appears on-screen.
• You must select a sleep time within three seconds of bringing up the sleep
timer screen. Otherwise, the screen will disappear and you will have to
start over.
– 15 –
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE PICTURE
a Press the MENU button to bring up the
g Use the + or – button to adjust the pic-
ture. The bar scale at the bottom of the
screen shows the level of adjustment.
menu screen.
MENU
TUE 1:35PM
h Press the MENU button until the picture
CLOCK SET
adjust screen appears.
PROGRAM TIMER
PICTURE ADJUST
CH PROGRAM
LANGUAGE
j Use the + or – button to highlight EXIT,
then press the MENU button to exit.
DEMONSTRATION
EXIT
[+] / [–] : MENU SELECT
[MENU] : ENTER
PICTURE ADJUST
ADJUST
RESET
EXIT
s Use the + or – button to highlight PIC-
TURE ADJUST, then press the MENU
button.
[+] / [–] : SELECT
[MENU] : EXIT
PICTURE ADJUST
ADJUST
RESET
EXIT
[+] / [–] : SELECT
[MENU] : ENTER
Picture Adjustments
FUNCTION
CONTRAST
BRIGHT(ness)
COLOR
– Button
Weaker
Darker
Paler
+ Button
Stronger
Lighter
d Press the MENU button while ADJUST
is highlighted.
Deeper
TINT
Skin tones Skin tones
to purple
to green
CONTRAST
63
SHARPNESS
Softer
Sharper
f Press the MENU button until the adjust-
ment you want to make (CONTRAST,
BRIGHTNESS, COLOR, TINT or
SHARPNESS –see chart at right for
details) appears at the bottom of the
screen.
NOTES
To reset the picture adjustments to their
original state, follow steps 1 and 2 above.
Use the + or – button to highlight RESET,
then press the MENU button. To exit,
press the MENU button while EXIT is
highlighted.
– 16 –
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE AUDIO, VIDEO AND EARPHONE JACKS
Audio/Video Input
The AUDIO and VIDEO IN (put) jacks on
the back of the TV allow you to receive au-
dio (sound) and video (picture) from exter-
nal sources, such as VCR, Video Disc, etc.
EXT.ANT.�
UHF/VHF
IN
DC－12V
VIDEO
AUDIO
Follow the instructions below to play video
from an external source.
1
Use audio/video cables (not included) to
connect the AUDIO and VIDEO IN (put)
jacks on the back of the TV to audio and
video output jacks on an external source.
Press the TV/VIDEO button to select the
VIDEO mode and the VIDEO indication
will appear on the screen.
Operate the VCR, Video Disc or etc. as
described in its owner’s manual. The TV
will monitor playback.
2
3
AUDIO OUT
VIDEO OUT
VCR
Earphone Jack Operation
Insert an earphone (not included) into the Earphone jack for private listening. When the
earphone is in use, the TV’s speaker is automatically shut off.
NOTES
• You must return the TV to TV mode for regular TV viewing.
•
If the TV does not receive a signal from an external source, the VIDEO display will appear on-screen.
DEMONSTRATION MODE
When placed in demonstration mode, your TV will display some of its features on-screen. Follow the
directions below to enter demonstration mode. To exit at any time, simply press the MENU button.
a Press the MENU button to bring up the
s
Use the + or – button to select DEMONSTRA-
TION, then press the MENU button. A demon-
stration of the TV’s features will begin.
menu screen.
MENU
TUE 1:35PM
MENU
TUE 1:35PM
CLOCK SET
PROGRAM TIMER
PICTURE ADJUST
CH PROGRAM
LANGUAGE
DEMONSTRATION
EXIT
CLOCK SET
PROGRAM TIMER
PICTURE ADJUST
CH PROGRAM
LANGUAGE
DEMONSTRATION
EXIT
[+] / [–] : MENU SELECT
[MENU] : ENTER
[+] / [–] : MENU SELECT
[MENU] : ENTER
d Press the MENU button to stop.
– 17 –
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE TV OPERATION
a Press the MENU button to bring up the main menu screen.
s Use the + or – button to highlight CH PROGRAM, then press the MENU button to
select it.
d Press the MENU button until CABLE appears to the right of AIR/CABLE.
On CATV (Cable Television) systems, programs are brought into the home on VHF chan-
nels 2–13, mid-band channels A–I, super band channels J–W, hyper band channels AA–
CCC, ultra band channels W+30–W+84 and sub midband channels (5A, A5–A1). When
CATV is selected, the numbers will change color from yellow to green to indicate the TV is
in the cable mode. Channels 2 through 13 are selected directly. Channel A can be tuned in
by selecting number 14 on this TV, channel B by selecting number 15, and so on as
follows:
Channel number on TV
Corresponding CATV Channel
14 15 16 17 18 19 20 21 22 23
A B C D E F G H I J
24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
K L M N O P Q R S T U V W AA BB CC
W+1 W+2 W+3
40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55
DD EE FF GG HH II JJ KK LL MM NN OO PP QQ RR SS
W+4 W+5 W+6 W+7 W+8 W+9 W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19
56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71
TT UU VV WW XX YY ZZ AAA BBB CCC
W+20 W+21 W+22 W+23 W+24 W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35
72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87
W+36 W+37 W+38 W+39 W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51
88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103
A5
A4
A3
A2
A1
W+59 W+60 W+61 W+62
W+52 W+53 W+54 W+55 W+56 W+57 W+58
104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119
W+63 W+64 W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78
120 121 122 123 124 125 1
5A
W+79 W+80 W+81 W+82 W+ 83 W+ 84
NOTE: The actual number of channels received depends upon channel reception in your
area or your cable system.
Most CATV systems use letters to designate channels but others use numbers. To tune in
a numbered channel, select the same number on the TV. Consult your local Cable TV
company to find out which of these channels are receivable and which type of Cable
system is used in your area. (Some cable TV systems use scrambled or encoded signals
and require special converters to receive these channels.)
– 18 –
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE REQUESTING SERVICE
Before requesting service, check the following list of problems and solutions. You may be
able to solve the problem yourself.
PROBLEM
No Power
SOLUTION
• Make sure the unit is plugged in.
• Unplug the unit from the electrical outlet for 60 seconds.
Then plug it in and turn it on again.
No picture
No Sound
• Make sure the antenna is properly connected at the back
of the TV.
• Make sure the antenna is not broken.
• Adjust the brightness and contrast controls.
• Use the VOLUME (Up/Down) buttons to turn up the vol-
ume.
• Make sure the sound is not muted by pressing the MUTE
button.
• Make sure the show is being transmitted in color by check-
ing to see if another channel is in color.
• Adjust the color control.
No Color
Wrong Color
• Adjust the color and tint controls.
Picture Too
Light/Dark
• Adjust the brightness and contrast controls.
• Check the antenna for shorted or broken wires.
• Reposition the antenna.
Picture Interference
• Try another channel to make sure there is not station trouble
or local interference (such as electric motors). If possible,
minimize by adjusting the antenna.
Remote control
Doesn’t Work
• Make sure batteries are inserted in the remote control.
• Make sure the remote control is aimed directly at the re-
mote sensor on the TV.
If you are still in need of assistance,
please call customer service at
1-800-919-3647
PRINTED IN MALAYSIA
1111-2742M178 G0001-1
Download from Www.Somanuals.com. All Manuals Search And Download.
|