READ AND SAVE THESE INSTRUCTIONS
Coffee Maker
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should
always be followed, including the following:
• Read all instructions.
• Do not touch hot surfaces. Use handles or knobs.
• To protect against electric shock, do not place cord, plugs, or
appliance in water or other liquid.
• Close supervision is necessary when any appliance is used by
or near children.
• Unplug from outlet when not in use and before cleaning. Allow
to cool before putting on or taking off parts, and before cleaning
the appliance.
• Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or has been damaged in any
manner. Contact Consumer Service for examination, repair or
adjustment.
• The use of an accessory not evaluated for use with this
appliance may cause injuries.
• Do not use outdoors.
• Do not let cord hang over edge of table or counter, or touch hot
surfaces.
• Do not place on or near a hot gas or electric burner, or in a
heated oven.
• To disconnect, press the Power Switch with LED Indicator Light
so that the light is off, then remove plug from wall outlet.
• Do not use appliance for other than intended use.
• Be certain lids are securely in place before operating appliance.
• Scalding may occur if the lid is removed during the brewing
cycles.
SAVE THESE INSTRUCTIONS
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
ADDITIONAL IMPORTANT
SAFEGUARDS
WARNING: This appliance generates heat and escaping steam
during use. Use proper precautions to prevent the risk of burns,
fires, or other injury to persons or damage to property.
• All users of this appliance must read and understand this
Owner’s Manual before operating or cleaning this appliance.
• The cord to this appliance should be plugged into a 120V AC
electrical outlet only.
• Use water only in this appliance! Do not put any other liquids
or food products in this appliance. Do not mix or add anything
to the water placed in this appliance, except as instructed in the
User Maintenance Instructions to clean the appliance.
• DO NOT attempt to move an appliance containing hot liquids.
Allow appliance to cool completely before moving.
• Keep appliance at least 4 inches away from walls or other
objects during operation. Do not place any objects on top of
appliance while it is operating. Place the appliance on a surface
that is resistant to heat.
• If this appliance begins to malfunction during use, immediately
unplug the cord. Do not use or attempt to repair the
malfunctioning appliance.
• If this appliance falls or accidentally becomes immersed in
water or any other liquid, unplug it immediately. Do not reach
into the water! Do not use this appliance after it has fallen
into or has become immersed in water. Contact Consumer
Service for examination and repair.
• Do not leave this appliance unattended during use.
• The appliance must be left to cool down sufficiently before
adding more water to avoid splattering.
• Always use fresh, cool water in your appliance. Warm water or
other liquids, except as listed in cleaning section, may cause
damage to the appliance.
• DO NOT lift Filter Basket Lid until brewing is complete, and all
parts have cooled.
• The Mugs are designed for use with this appliance. They must
never be used on a range top.
• DO NOT put mugs into a microwave.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
CAUTION: A short power supply cord is provided to reduce the
risk resulting from becoming entangled in or tripping over a longer
cord. Do not use an extension cord with this product.
POLARIZED PLUG: This appliance has a polarized plug, (one
blade is wider than the other). To reduce the risk of electric shock,
this plug is intended to fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Do not attempt to modify the
plug in any way.
CAUTION: To prevent Plasticizers from migrating from the finish of
the countertop or tabletop or other furniture, place NON-PLASTIC
coasters or placemats between the appliance and the finish of the
countertop or tabletop.
Failure to do so may cause the finish to darken, permanent
blemishes may occur or stains can appear.
ELECTRIC POWER: If the electric circuit is overloaded with other
appliances, your appliance may not operate properly. It should be
operated on a separate electrical circuit from other appliances.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT REMOVE THE BOTTOM COVER. NO USER-
SERVICABLE PARTS INSIDE. REPAIR SHOULD BE DONE BY
AUTHORIZED SERVICE PERSONNEL ONLY.
Before Using Your Take 2™
Programmable Clock Timer
Coffee Maker
Before using your Take 2™ Programmable Clock Timer Coffee
Maker for the first time, we suggest you become familiar with all of
its parts. Read all instructions and cautions carefully.
CAUTION: Press the Power Switch with LED Indicator Light so
that the light is off. Unplug from outlet.
IMPORTANT: Never place Thermal Mugs on a hot stove or in a
microwave. Never let Thermal Mugs stand in water.
Before brewing coffee, follow instructions for cleaning. See “Care
and Cleaning,” page 8.
CAUTION: Do not immerse cord, plug, or coffee maker unit in
water or other liquids.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Your product may vary slightly from illustration.
Parts Identification
Filter Basket
(P/N 31142)
Water Chamber
with Water Level
Indicator
Filter
Basket
Holder
Mug Lid(s)
(P/N 30909)
Flow Nozzle
(P/N 31144)
FIGURE B
Thermal Mugs
(P/N 30911)
Drip Tray
(P/N 31145)
Overflow
Tray
(P/N 31143)
Base
FIGURE A
FIGURE C
FIGURE D
FIGURE E
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Setting the Clock
1. Plug into 120 V~60 Hz outlet.
2. The display will go to AM 12:00 and continue to flash until you
press a button.
3. Press the Program button, “SET TIME” will be displayed in the
top right corner.
4. Press and hold the HR button for rapid hour advancement.
When the desired hour is reached, release the button.
5. Press and hold the MIN button for rapid minute advancement.
When the desired minute is reached, release the button.
6. Press the PROG button again. The time is now set. If you do
not press the PROG button again, the display will
automatically return to the time of day after 10 seconds.
Brewing
1. Plug into 120V ~ 60 Hz outlet.
2. Make sure unit is in the OFF position. The LED Indicator Light
will be off.
IMPORTANT: Place coffee maker on a level surface.
3. Markings on the Water Level Indicator indicate the amount of
water required to brew the desired number of Thermal Mugs.
Lift up the hinged Water Chamber Lid and fill to desired level
with cold, fresh water for the number of Thermal Mugs (one or
two), using the Water Level Indicator on the Water Window.
WARNING: When making one Thermal Mug, do not fill above
level 1.
IMPORTANT: If cream or milk will be added to Thermal Mugs,
use less water for brewing.
4. For optimal holding temperature, rinse the inside of Thermal
Mugs with warm water before brewing. Place Lids securely on
tops of Thermal Mugs. Press down on the Lids to ensure
proper fit.
NOTE: You can brew either one Thermal Mug or two Thermal
Mugs at once. Place Thermal Mugs snugly on Base of unit as
shown in Figure A (for two Thermal Mugs). The contoured
design on the Base should be used as a guide for Thermal
Mug alignment.
5. Insert a #2 paper cone filter into the Removable Filter Basket
and add coffee grounds. Use approximately 12-2 tablespoons
for each Thermal Mug of coffee. Close Water Chamber Lid,
snapping the Basket into place. (See Figure D.)
Download from Www.Somanuals.com. All Manuals Search And Download.
7
6. Press Power Switch ON. The LED Indicator Light will turn red.
CAUTION: Avoid contact with heated water.
IMPORTANT: Do not remove Thermal Mugs until the LED
Indicator Light has turned OFF. The LED Indicator Light will
turn OFF approximately two minutes after brewing is
complete. This delay will allow the last drops of coffee to flow
into the Thermal Mugs.
7. After LED Indicator Light turns off, Thermal Mugs may be
safely removed.
8. If brewing more than one cycle, allow unit to cool for 10
minutes between cycles.
Helpful Hints for Brewing
• Always use fresh, cold water for brewing. In areas with hard
water or where water contains a high mineral content, use cold
filtered water for optimal coffee taste.
• For best results, use Melitta® #2 paper cone filters and Melitta®
Premium Coffee.
• The markings on the Water Level Indicator reflect the quantity
of fresh water to be used. The quantity of brewed coffee is less
because the coffee grounds absorb water.
Programming a Delayed Brew
1. Press the PROG button twice, “SET TIMER” will be displayed
in the bottom center of the Display Window.
2. Using the HR and MIN button, set the time you wish the coffee
to begin brewing. Once the time is set, the display will return
to the time of day automatically after 8 seconds, and then
“SET TIMER” will disappear. You may also press the PROG
button to make the display return to the time of day.
3. Press AUTO button, LED Indicator Light will be green to
indicate the timer has been set for delayed start.
Note:To cancel the delayed start, press AUTO once again, the
LED Indicator Light will go off and the delayed start program
will be cancelled.
4. When the delayed start program has reached the preset time,
the LED Indicator Light will change to red and the brewing will
start.
Note: During the auto-brew program, you may start brewing at
once by pressing the ON/OFF button.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Care and Cleaning
1. Make sure Power Switch is in the OFF position. The LED
Indicator Light will be off.
2. Unplug and allow to cool completely before cleaning.
3. Open Filter Basket Holder and lift up on the tab of Filter
Basket. Discard any paper filter and coffee grounds.
4. Wash removable Filter Basket, Drip Tray and Overflow Tray,
Mugs and Mug Lids in warm, soapy water. Rinse and dry
thoroughly. Or, you may wash the Mugs and Lids in the top
rack of a dishwasher.
5. Clean the outside of the coffee maker with a damp cloth.
CAUTION: DO NOT IMMERSE CORD, PLUG OR COFFEE
MAKER UNIT IN WATER OR OTHER LIQUID.
6. Replace Filter Basket, Drip Tray and Overflow Tray for next use.
Descaling
We recommend that you descale your coffee maker once a month
because mineral deposits can form a coating in the coffee maker,
causing slower brewing time and possibly an off flavor in the
coffee. Use a cleaner recommended for coffee makers. To descale
your unit:
1. Pour two ounces of vinegar or coffee cleaner into the Water
Chamber. Add cold water to the level 2 indicator.
2. Place a clean #2 paper cone filter in the filter basket and close
Water Chamber Lid. Place both Mugs in proper position on
Base of unit.
3. Follow “Brewing” instructions (without coffee).
4. When the LED Indicator Light turns off, wait 15 minutes and
pour solution from Mugs back into coffee maker. Be sure that
the Filter Basket is still in proper position.
5. Turn unit on again. Allow all solution to empty into Mugs.
When LED Indicator Light turns off, discard solution.
6. Allow unit to cool 10 minutes. To rinse unit, fill Water Chamber
with fresh, cold water up to the level 2 indicator. Insert a fresh
paper filter into Filter Basket. Close Water Chamber Lid. Place
both Mugs in proper position on Base of unit and turn Power
Switch on.
7. At end of cycle, allow unit to cool, discard water and paper
filter. Wash and dry Mugs and other removable parts.
8. Unplug coffee maker from outlet. When coffee maker has
cooled, wipe exterior with a damp cloth.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
IMPORTANT NOTICE
If any parts are missing or defective,
DO NOT return this product.
Please call our Customer Relations Department for assistance.
800-233-9054 Monday - Friday 9am - 5pm CST
LIMITED ONE YEAR WARRANTY
Warranty: This Melitta® product is warranteed by Salton, Inc. to be free from defects
in materials or workmanship for a period of (1) year from the original purchase date.
This product warranty covers only the original consumer purchaser of the product.
Warranty Coverage: This warranty is void if the product has been damaged by
accident in shipment, unreasonable use, misuse, neglect, improper service,
commercial use, repairs by unauthorized personnel, normal wear and tear, improper
assembly, installation or maintenance abuse or other causes not arising out of
defects in materials or workmanship. This warranty is effective only if the product is
purchased and operated in the USA, and does not extend to any unit which has been
used in violation of written instructions furnished with the product, or to units which
have been altered or modified, or to damage to products or parts thereof which have
had the serial number removed, altered, defaced or rendered illegible.
Implied Warranties: ANY IMPLIED WARRANTIES WHICH THE
PURCHASER MAY HAVE ARE LIMITED IN DURATION TO ONE (1) YEAR FROM
THE DATE OF PURCHASE. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you.
Warranty Performance: During the above one-year warranty period, a product with
a defect will be either repaired or replaced with a reconditioned comparable model
(at our option) when the product is returned to the Repair Center, or the purchase
price refunded. The repaired or replacement product will be in warranty for the
balance of the one-year warranty period and an additional one-month period. No
charge will be made for such repair or replacement.
Service and Repair: Should the appliance malfunction, you should first call toll-free
1-800-233-9054 between the hours of 9:00 am and 5:00 pm Central Standard Time
and ask for CONSUMER SERVICE stating that you are a consumer with a problem.
Please refer to model number ME2TMDS when you call.
In-Warranty Service (USA): For an appliance covered under the warranty period, no
charge is made for service or postage. Call for return authorization 1-800-233-9054.
Out-of Warranty Service: A flat rate charge by model is made for out-of-warranty
service. Include $8.00 (U.S.) for return shipping and handling. We will notify you by
mail of the amount of the charge for service and require you to pay in advance for
the repair or replacement.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
For Products Purchased in the USA, but Used in Canada: You may return the
product insured, packaged with sufficient protection, and postage and insurance
prepaid to the USA address listed below. Please note that all customs duty /
brokerage fees, if any, must be paid by you and we will require you to pay the cost of
customs duty / brokerage fees to us in advance of our performing any service.
Risk During Shipment: We cannot assume responsibility for loss or damage
during incoming shipment. For your protection, carefully package the product for
shipment and insure it with the carrier. Be sure to enclose the following items with
your appliance: any accessories related to your problem, your full return address and
daytime phone number, a note describing the problem you experienced, a copy of
your sales receipt or other proof of purchase to determine warranty status. C.O.D.
shipments cannot be accepted.
To return the appliance, ship to:
Attn: Repair Center
To contact us, please write, call or email:
Salton, Inc.
Salton, Inc.
P.O. Box 6916
708 South Missouri Street
Macon, MO 63552
Columbia, MO 65205-6916
1-800-233-9054
Email: [email protected]
Limitation of Remedies: No representative or person is authorized to assume for
Salton, Inc. any other liability in connection with the sale of our products. There shall
be no claims for defects or failure of performance or product failure under any theory
of tort, contract or commercial law including, but not limited to negligence, gross
negligence, strict liability, breach of warranty and breach of contract. Repair,
replacement or refund shall be the sole remedy of the purchaser under this warranty,
and in no event shall Salton, Inc. be liable for any incidental or consequential
damages, losses or expenses. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation or exclusion may not
apply to you.
Legal Rights: This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
© 2004 Salton, Inc.
All Rights Reserved
P/N 61575
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|