Loudspeaker System
XCS2K
Owner’s Manual
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank You
Table of Contents
Your decision to own this McIntosh XCS2K Loudspeaker
System ranks you at the very top among discriminating
music listeners. You now have “The Best.” The McIntosh
dedication to “Quality,” is assurance that you will receive
many years of listening enjoyment from this unit.
Please take a short time to read the information in this
manual. We want you to be as familiar as possible with all
the features and functions of your new McIntosh.
Safety Instructions............................................................2
Thank You and Please Take a Moment.............................3
Technical Assistance and Customer Service....................3
Table of Contents and General Information .....................3
Introduction.......................................................................4
Performance Features .......................................................5
Dimensions ................................................................... 6-8
Installation ...................................................................9-10
Rear Panel Connections.................................................. 11
How to Connect using a single Amplifier ...................... 12
How to Connect using two Amplifiers............................14
Connection Diagram (Separate Sheet) .....................Mc1A
How to Connect using three Amplifiers..........................15
Connection Diagram (Separate Sheet) .....................Mc1B
Specifications.................................................................. 18
Packing Instruction.........................................................19
Please Take A Moment
The serial number, purchase date and McIntosh Dealer
name are important to you for possible insurance claim or
future service. The spaces below have been provided for
you to record that information:
Serial Number: __________________________________
Purchase Date: __________________________________
Dealer Name: ___________________________________
General Information
Caution: The XCS2K weight is 294 pounds (133.4kg). It re-
quires three or more persons to safely handle the Loudspeaker
System.
1. Loudspeaker Cables of adequate size are important to en-
sure that there will be no significant power loss or heating.
Cable size is specified in Gauge numbers or AWG (Ameri-
can Wire Gauge). The smaller the Gauge number, the larger
the wire size:
Technical Assistance
If at any time you have questions about your McIntosh
product, contact your McIntosh Dealer who is familiar
with your McIntosh equipment and any other brands that
may be part of your system. If you or your Dealer wish
additional help concerning a suspected problem, you can
receive technical assistance for all McIntosh products at:
If the Loudspeaker Cables are 50 feet (38.1m) or less,
use at least 12 Gauge (AWG) wire size or larger.
If the Loudspeaker Cables are 100 feet (76.2m) or less,
use at least 10 Gauge (AWG) wire size or larger.
2. For additional connection information, refer to the owner’s
manual(s) for any component(s) connected to the XCS2K
Loudspeaker.
3. The XCS2K’s built-in speaker protection incorporates five
automatic resetting solid-state devices in the crossover
networks. One protects the tweeters, one for the midranges
and three for the woofers. The protection allows a certain
amount of overdrive but extended periods will trigger pro-
tection. If an obvious lack of high, mid or low frequencies
is noticed, the Protection Device may have activated. These
devices will automatically reset when the volume level is
reduced significantly and kept low until the output of the
affected Loudspeaker Element returns to normal.
4. When the XCS2K Loudspeaker System is driven by more
than one amplifier, the output levels of the different ampli-
fiers connected to the Loudspeaker System must be adjusted
to achieve a proper balance between the low, midrange
and high frequencies reproduced. This adjustment is best
achieved through the use of audio test equipment operated
by a qualified installer.
McIntosh Laboratory, Inc.
2 Chambers Street
Binghamton, New York 13903
Phone: 607-723-1545
Fax: 607-724-0549
Customer Service
If it is determined that your McIntosh product is in need of
repair, you can return it to your Dealer. You can also return
it to the McIntosh Laboratory Service Department. For
assistance on factory repair return procedure, contact the
McIntosh Service Department at:
McIntosh Laboratory, Inc.
2 Chambers Street
Binghamton, New York 13903
Phone: 607-723-3515
Fax: 607-723-1917
Copyright 2007 © by McIntosh Laboratory, Inc.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The new McIntosh XCS2K Loudspeaker System is a
Center Channel Loudspeaker capable of reproducing the
full dynamic range of a symphony orchestra with very low
audible distortion. It is the perfect match to the famous
XRT2K Column Loudspeakers, when used in a Home
Theater / Music System. It uses the same acoustic technol-
The Low Frequency Section of the System consists of
three 12 inch Aluminum Cone Woofers capable of long
cone excursions. Refer to figure 3. The sound produced has
very low levels of harmonic distortion and a frequency re-
sponse down
to 16Hz. They
ogy found in the XRT2K Column Loudspeakers developed have a large
by the McIntosh Acoustic Engineers. The technology has
been refined over the years and is now the 6th generation
of the design and provides superior quality sound repro-
duction in a full range system.
The XCS2K Loudspeaker
utilizes a Horizontal Arc Array
motor as-
sembly made
with High
Temperature
Neodymium
magnets
Design with three-quarter inch
Titanium Dome Tweeters and
multiple rows of two inch Mid-
range Inverted Titanium Dome
with inherent
shielding to
greatly reduce
any external
Figure 3
Drivers. Refer to figures 1, 2A
and 2B. The Sound Waves from
this Horizontal Arc Array pro-
magnetic field. The woofer design also utilizes an alu-
minum shorting ring and copper capped pole piece. This
results in lower distortion due to more linear magnetic flux
in the voice coil gap. A good example of this low distor-
tion is incredible smoothness and effortless clarity in the
reproduction of the human voice.
The Crossover Networks used in the XCS2K Loud-
speaker System are phase matched between the Low
Frequency, Midrange and High Frequency Sections to
ensure a smooth frequency response over the entire audible
range. Refer to figures 4, 5 and 6. The crossover inductors
are selected so they will not add audible distortion. The
network capacitors are film type for extra reliability. All
the Capacitors and Inductors are chosen for high current
capacity. Each section of the network utilizes it own self
resetting high current PPTC type fuses to provide an extra
measure of protection.
Figure 1
duce a stable and focused
symmetrical horizontal
sound image. Since the
audio power fed to each
row is distributed among
all the drivers, each
driver does not have to
work as hard, resulting
in greater power han-
dling capability, greatly
reduced power com-
pression and a dramatic
reduction in distortion.
Figure 2A
Figure 2B
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction and Performance Features
• Shielded Magnetic Field
The XCS2K may also be used in Home Theater Installa-
tions near a television receiver or monitor without caus-
ing the television image to degrade. By design, all of the
speaker’s magnetic structures are inherently shielded
which prevents interference.
• Low Harmonic and Intermodulation Distortion
The XCS2K Loudspeaker System is capable of reproduc-
ing the full dynamic range of a symphony orchestra with
very low audible distortion of any kind.
Figure 4
Figure 5
Figure 6
• High Power Handling
The Loudspeaker Elements and Crossover Components of
the XCS2K are all chosen for use with powerful amplifiers
up to 2,000 watts.
• Superior Imaging
Locating the Tweeters between the two rows of Midranges
generates a symmetrical response for superior imaging.
• Versatile Operation and Placement
In addition to the regular connections, the XCS2K Loud-
speaker System provides separate connections for Bi-
Amplification and Tri-Amplification hookups, as well as
Bi-Wiring and Tri-Wiring.
· Extruded and Machined Side Panels and Column
The top and bottom of the XCS2K Low Frequency en-
closure and the Midrange/Tweeter Column enclosure are
machined from extruded thick aluminum panels to be
non-parallel and are given a High Gloss Black Piano Type
Finish.
• Gold Plated Input Connectors
The XCS2K input connectors are gold plated for superior
corrosion resistance and high electrical conductivity.
Performance Features
• High Temperature Neodymium-Iron-Boron Alloy
Magnets
The 3 twelve inch Woofers, 32 two inch Midranges and 20
three-quarter inch Dome Tweeters all use the Neodymium-
Iron-Boron magnets. This Alloy has the highest flux den-
sity per unit of volume and helps to keep the Loudspeaker
System weight to a minimum while preserving the utmost
in performance.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
The following dimensions can assist in determining the
best location for your XCS2K Loudspeaker System.
Front View of the
XCS2K
Loudspeaker System
17-1/16"
43.34cm
42-1/4"
107.3cm
Side View of the
XCS2K
23-3/8"
59.37cm
Loudspeaker System
(shown at maximum
elevation of 30°)
26-3/4"
67.95cm
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
32-7/8"
83.50cm
Rear View of the
XCS2K
Loudspeaker System
24-7/8"
61.18cm
22-1/2"
57.15cm
14-1/2"
36.83cm
9-7/8"
25.1cm
12-1/8"
30.80cm
5-3/16"
13.2cm
4-1/8"
10.48cm
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1-3/4"
4.45cm
Front View of the XCS2K
4-1/2"
11.43cm
Midrange and High Frequency Horizontal Array
11-5/16"
28.73cm
9-1/2"
24.13cm
7-11/16"
19.53cm
2-3/16"
5.56cm
4-5/8"
11.75cm
Front View of the XCS2K
Low Frequency Horizontal Array
9-1/2"
24.13cm
8-3/8"
21.27cm
12-3/4"
32.39cm
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions, con’t and Installation
Installation
Location in the Room
Unpacking the Loudspeaker
The XCS2K Loudspeaker is designed for use as a Center
Channel in a Home Theater System. The optimal method
for selecting all the Loudspeaker Locations in a Home
Theater System includes the use of a real time spectrum
analyzer operated by an experienced system installer. An
uncompromising installation would take into consideration
the floor, wall and ceiling coverings, the type and place-
ment of furniture and can even include the architectural
design of the room and its construction materials. In those
To protect the fine finish of the XCS2K Loudspeaker
System during the adjustment process, it is advisable to
prepare a suitable adjustment area. A freshly vacuumed
carpeted area covered with a soft, clean fabric, such as a
large bed linen or blanket would be suitable. Start by un-
packing the Loudspeaker.
It is recommended that the Professionals at your McIn-
tosh Dealer, who are skilled in all aspects of installation
and operation, install the XCS2K Loudspeaker System and
instances where placement in the room is fixed an environ- any associated audio equipment.
CAUTION: When this Loudspeaker is assembled it weighs
mental equalizer may be needed to restore proper musical
balance.
294 pounds (133.4 kgs). It requires three or more
persons to safely handle during assembly, adjust-
ment and placement in the room.
The XCS2K Loudspeaker’s Smooth Frequency Re-
sponse may be altered by large object(s) located in the path
of the sound waves or by locating the Loudspeaker too
close to a side wall. There should be an unobstructed area
in front of the XCS2K Loudspeaker on either side of the
center axis for the best performance. The optimum loca-
tion in a Home Theater System is directly under or in front
of the TV/Monitor. Refer to figures 7 and 8.
1. Orient the XCS2K shipping carton with the arrows on
the outside of the carton pointing upward.
2. Remove the banding material from the shipping carton.
3. Lift off the top of the shipping carton and set it aside.
4. Remove the Top Foam from the Loudspeaker.
5. Remove the Blue Protective Cloth Cover and set it
aside.
6. While facing a side of the Loudspeaker, remove the side
cover by grasping the outside edges of the cover and
pulling towards you.
In a similar manner,
remove the other side
cover from the Loud-
speaker. Place both cov-
ers on to the previously
removed protective cloth
cover for safe keeping.
Side
Cover
Figure 9
Refer to figures 9 and
10.
Figure 7
Top View
Remove Covers
Right Side
Cover
Left Side
Cover
Figure 10
Figure 8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, con’t
7. With three persons, lift up on the sides and center rear
of the Low Frequency Enclosure part of the Loudspeak-
er. Place the Loudspeaker in the final location. Refer to
figure 11.
Figure 13
Top View of
Lift Areas
Figure 11
Adjusting the Elevation of the Loudspeaker
The acoustic output of the XCS2K Loudspeaker may be
directed to line up with the height of the average ear in the
prime viewing/listening area. There is a 30 degree range of
adjustment built-in.
1. Using an approprate tool, remove the hex head locking
bolt (used during shipping) from each side of the Loud-
speaker and retain them for possible future use. Refer
to figure 12.
Figure 14
Locking
2. While two
Bolt
persons are
loosening
the hex head
adjustment
bolt on
each side of
the Loud-
speaker, a
Adjustment
Bolt
third person
needs to as-
Figure 12
sist by stabilizing the front of the Loudspeaker.
3. Rotate the Loudspeaker so the center axis of the Loud-
speaker is pointed toward ear level when seated in the
main viewing/listening area. Figure 13 illustrates a fif-
teen degree angle and figure 14 is a thirty degree angle.
4. Tighten the adjustment bolt on both sides of the Loud-
speaker.
5. Reinstall the previously removed side covers.
6. Proceed to “How to connect” starting on page 12.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, con’t and Rear Panel Connections
LOW Frequency Input Con-
nections 1, 2, and 3 for a 8 ohm
Loudspeaker.
Note: 1, 2 and 3 Terminals (+)
are internally connected
together; 1, 2 and 3 Termi-
nals (-) are also internally
connected together.
HIGH Frequency Input Con-
nections 1, 2, and 3 for a 8 ohm
Loudspeaker.
Note: 1, 2 and 3 Terminals (+)
are internally connected
together; 1, 2 and 3 Termi-
nals (-) are also internally
MIDrange Frequency Input Con-
nections 1, 2, and 3 for a 8 ohm
connected together.
Loudspeaker.
Note: 1, 2 and 3 Terminals (+)
are internally connected
together; 1, 2 and 3 Termi-
nals (-) are also internally
connected together.
3
3
2
2
1
1
3
3
2
2
1
1
3
3
2
2
1
1
11
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect using a single Amplifier
Caution: The AC Power Cord should not be connected to the
Power Amplifier until after the Loudspeaker Con-
nections have been made. Failure to observe this
could result in Electric Shock.
6. Connect a Loudspeaker cable from the XCS2K LOW
Frequency INPUTS 3 (-) Binding Post to the (-) Bind-
ing Post A of the Power Amplifier.
7. Connect a Loudspeaker cable from the XCS2K LOW
Frequency INPUTS 3 (+) Binding Post to the (8 ohm)
Binding Post A of the Power Amplifier.
1. Prepare Loudspeaker cables by choosing one of the
methods below:
8. Tighten all of the Loudspeaker and Amplifier Binding
Posts.
Bare wire cable ends:
Carefully remove sufficient insulation from the
cable ends, refer to figures 20, 21 & 22. If the cable
is stranded, carefully twist the strands together as
tightly as possible.
Figure 21
Figure 22
Figure 20
Note: If desired, the twisted ends can be tinned with
solder to keep the strands together or attach
spade lugs.
Spade lug or prepared wire connection:
Insert the spade lug connector or prepared section
of the cable end into the terminal side access hole,
and tighten the terminal cap until the cable is firmly
clamped into the terminal so the wires cannot slip
out. Refer to figures 23, 24 & 25.
Figure 23
Figure 24
Figure 25
2. Connect a Loudspeaker cable from the XCS2K HIGH
Frequency INPUTS 3 (-) Binding Post to the (-) Bind-
ing Post C of the Power Amplifier.
Note: It is important to maintain the correct polarity at
both ends of the Loudspeaker cables.
3. Connect a Loudspeaker cable from the XCS2K HIGH
Frequency INPUTS 3 (+) Binding Post to the (8 ohm)
Binding Post C of the Power Amplifier.
4. Connect a Loudspeaker cable from the XCS2K MID
Frequency INPUTS 3 (-) Binding Post to the (-) Bind-
ing Post B of the Power Amplifier.
5. Connect a Loudspeaker cable from the XCS2K MID
Frequency INPUTS 3 (+) Binding Post to the (8 ohm)
Binding Post B of the Power Amplifier.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect
McIntosh MC2KW Power Amplifier
3
2
1
3
2
1
3
2
1
13
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect using a two Amplifiers
Caution: The AC Power Cord should not be connected to the
Power Amplifiers until after the Loudspeaker Con-
nections have been made. Failure to observe this
could result in Electric Shock.
Follow the connection instructions below, together with the
Connection Diagrams located on the separate folded sheet
“Mc1A and 1B”, as this represents an example of a typical
audio system. Your system may vary from this, however
the actual components would be connected in a similar
manner.
5. Connect a Loudspeaker cable from the XCS2K MID
Frequency INPUTS 2 (+) Binding Post to the (8 ohm)
Binding Post B of the Power Amplifier number two.
6. Connect a Loudspeaker cable from the XCS2K MID
Frequency INPUTS 3 (-) Binding Post to the (-) Bind-
ing Post A of the Power Amplifier number two.
7. Connect a Loudspeaker cable from the XCS2K MID
Frequency INPUTS 3 (+) Binding Post to the (8 ohm)
Binding Post A of the Power Amplifier number two.
8. Connect Loudspeaker cables from the XCS2K LOW
Frequency INPUTS 3 (-) and (+) Binding Posts to the
(-) and (8 ohm) Binding Posts A of the Power Amplifier
number one.
1. Prepare Loudspeaker cables by choosing one of the
methods below:
Bare wire cable ends:
Carefully remove sufficient insulation from the cable
ends, refer to figures 20, 21 & 22. If the cable is
stranded, carefully twist the strands together as tightly
as possible.
9. Connect Loudspeaker cables from the XCS2K LOW
Frequency INPUTS 2 (-) and (+) Binding Posts to the
(-) and (8 ohm) Binding Posts B of the Power Amplifier
number one.
10. Connect Loudspeaker cables from the XCS2K LOW
Frequency INPUTS 1 (-) and (+) Binding Posts to the
(-) and (8 ohm) Binding Posts C of the Power Ampli-
fier number one.
11. Tighten all of the Loudspeaker and Amplifier Binding
Posts.
Figure 21
Figure 22
Figure 20
Note: If desired, the twisted ends can be tinned with solder
to keep the strands together or attach spade lugs.
Spade lug or prepared wire connection:
Insert the spade lug connector or prepared section
of the cable end into the terminal side access hole,
and tighten the terminal cap until the cable is firmly
clamped into the terminal so the wires cannot slip out.
Refer to figures 23, 24 & 25.
Figure 23
Figure 24
Figure 25
2. Connect a Loudspeaker cable from the XCS2K HIGH
Frequency INPUTS 3 (-) Binding Post to the (-) Bind-
ing Post C of the Power Amplifier number two.
Note: It is important to maintain the correct polarity at
both ends of the Loudspeaker cables.
3. Connect a Loudspeaker cable from the XCS2K HIGH
Frequency INPUTS 3 (+) Binding Post to the (8 ohm)
Binding Post C of the Power Amplifier number two.
4. Connect a Loudspeaker cable from the XCS2K MID
Frequency INPUTS 2 (-) Binding Post to the (-) Bind-
ing Post B of the Power Amplifier number two.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect using a three Amplifiers
Caution: The AC Power Cord should not be connected to the
Power Amplifiers until after the Loudspeaker Con-
nections have been made. Failure to observe this
could result in Electric Shock.
4. Connect Loudspeaker cables from the XCS2K HIGH
Frequency INPUTS 1 (-) and (+) Binding Posts to the
(-) and (8 ohm) Binding Posts A of the Power Ampli-
fier number three.
Follow the connection instructions below, together with the
Connection Diagrams located on the separate folded sheet
“Mc1A and 1B”, as this represents an example of a typical
audio system. Your system may vary from this, however
the actual components would be connected in a similar
manner.
5. Connect Loudspeaker cables from the XCS2K MID
Frequency INPUTS 3 (-) and (+) Binding Posts to the
(-) and (8 ohm) Binding Posts B of the Power Ampli-
fier number two.
6. Connect Loudspeaker cables from the XCS2K MID
Frequency INPUTS 2 (-) and (+) Binding Posts to the
(-) and (8 ohm) Binding Posts B of the Power Ampli-
fier number two.
7. Connect Loudspeaker cables from the XCS2K MID
Frequency INPUTS 1 (-) and (+) Binding Posts to the
(-) and (8 ohm) Binding Posts C of the Power Ampli-
fier number two.
8. Connect Loudspeaker cables from the XCS2K LOW
Frequency INPUTS 3 (-) and (+) Binding Posts to the
(-) and (8 ohm) Binding Posts A of the Power Ampli-
fier number one.
1. Prepare Loudspeaker cables by choosing one of the
methods below:
Bare wire cable ends:
Carefully remove sufficient insulation from the cable
ends, refer to figures 20, 21 & 22. If the cable is
stranded, carefully twist the strands together as tightly
as possible.
9. Connect Loudspeaker cables from the XCS2K LOW
Frequency INPUTS 2 (-) and (+) Binding Posts to the
(-) and (8 ohm) Binding Posts B of the Power Ampli-
fier number one.
10. Connect Loudspeaker cables from the XCS2K LOW
Frequency INPUTS 1 (-) and (+) Binding Posts to the
(-) and (8 ohm) Binding Posts C of the Power Amplifier
number one.
Figure 21
Figure 22
Figure 20
Note: If desired, the twisted ends can be tinned with solder
to keep the strands together or attach spade lugs.
Spade lug or prepared wire connection:
Insert the spade lug connector or prepared section
of the cable end into the terminal side access hole,
and tighten the terminal cap until the cable is firmly
clamped into the terminal so the wires cannot slip out.
Refer to figures 23, 24 & 25.
11. Tighten all of the Loudspeaker and Amplifier Binding
Posts.
Figure 23
Figure 24
Figure 25
2. Connect Loudspeaker cables from the XCS2K HIGH
Frequency INPUTS 3 (-) and (+) Binding Posts to the
(-) and (8 ohm) Binding Posts B of the Power Ampli-
fier number three.
Note: It is important to maintain the correct polarity at
both ends of the Loudspeaker cables.
3. Connect Loudspeaker cables from the XCS2K HIGH
Frequency INPUTS 2 (-) and (+) Binding Posts to the
(-) and (8 ohm) Binding Posts C of the Power Ampli-
fier number three.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications
General Specifications
System Driver Complement
Finish Enclosures
Three 12 inch Aluminum Cone Woofers
Thirty-Two 2 inch Titanium Inverted
Dome Midranges
High Gloss Black Aluminum Sides, Brushed Aluminum
Front and Back, High Gloss Black Top and Bottom
Twenty 3/4 inch Titanium Dome Tweeters
Finish Grille
Black Knit Cloth with High Gloss Black Trim
Impedance
8 ohms Nominal
Overall Dimensions
Width is 42-1/4 inches (107.3cm)
Height is 23-3/8 inches (59.37cm) including feet
Depth is 26-3/4 inches (67.95cm)
Frequency Response
16Hz - 45kHz
Sensitivity
Weight
86dB (2.8V/1m equivalent)
294 pounds (133.4 kg) net
314 pounds (142.4kg) in shipping carton
Crossover Frequencies
250Hz
1,500Hz
Power Handling
2,000 Watts Maximum
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing Instructions
Packing Instructions
In the event it is necessary to repack the equipment for
shipment, the equipment must be packed exactly as shown
below. To protect the finish of the Loudspeaker it is advis-
able to place it in the original protective cotton blue cover
before placing them into the shipping carton.
Use the original shipping carton and interior parts only
if they are all in good serviceable condition. If a shipping
carton or any of the interior part(s) are needed, please call
or write Customer Service Department of McIntosh Labo-
ratory. Please see the Part List for the correct part numbers.
Quantity Part Number
Description
1
1
1
1
1
034395
034396
034398
034397
034353
Top shipping carton
Bottom shipping carton
Top foam
Bottom foam
Blue Protective cloth cover
Top
Shipping
Carton
Top
Foam
Blue
Protective
Cloth Cover
Bottom
Foam
Bottom
Shipping
Carton
19
Download from Www.Somanuals.com. All Manuals Search And Download.
McIntosh Laboratory, Inc.
2 Chambers Street
Binghamton, NY 13903
The continuous improvement of its products is the
policy of McIntosh Laboratory Incorporated who
reserve the right to improve design without notice.
Printed in the U.S.A.
McIntosh Part No. 04101700
Download from Www.Somanuals.com. All Manuals Search And Download.
|