McCulloch Lawn Mower MC1136 User Manual

MODEL NO. MC1136 (MC1136B)  
11 HP 36 Inch  
Lawn Tractor  
532 19 38-89 Rev. 1 9.15.04 RD  
PRINTED IN U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY RULES  
Safe Operation Practices for Ride-On Mowers  
GENERAL SERVICE  
III. CHILDREN  
Never operate machine in a closed are.  
Keep all nuts and bolts tight to be sure the equipment  
is in safe working condition.  
Never tamper with safety devices. Check their proper  
operation regularly.  
Keep machine free of grass, leaves, or other debris  
build-up. Clean oil or fuel spillage and remove any fuel-  
soaked debris. Allow machine to cool before storing.  
If you strike a foreign object, stop and inspect the  
machine. Repair, if necessary, before restarting.  
Nevermakeanyadjustmentsorrepairswiththeengine  
running.  
Check grass catcher components and the discharge  
guard frequently and replace with manufacturer's rec-  
ommended parts, when necessary.  
Tragic accidents can occur if the operator is not alert to  
the presence of children. Children are often attracted to  
the machine and the mowing activity. Never assume that  
children will remain where you last saw them.  
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Never allow children to operate the machine.  
Useextracarewhenapproachingblindcorners,shrubs,  
trees, or other objects that may block your view of a  
child.  
Mower blades are sharp. Wrap the blade or wear  
gloves, and use extra caution when servicing them.  
Check brake operation frequently. Adjust and service  
as required.  
Maintain or replace safety and instruction labels, as  
necessary.  
IV. TOWING  
Tow only with a machine that has a hitch designed for  
towing. Do not attach towed equipment except at the  
hitch point.  
Follow the manufacturer's recommendation for weight  
limits for towed equipment and towing on slopes.  
Never allow children or others in or on towed equip-  
ment.  
On slopes, the weight of the towed equipment may  
cause loss of traction and loss of control.  
Travel slowly and allow extra distance to stop.  
Be sure the area is clear of bystanders before operat-  
ing. Stop machine if anyone enters the area.  
Never carry passengers.  
Do not mow in reverse unless absolutely necessary.  
Always look down and behind before and while back-  
ing.  
V. SERVICE  
SAFE HANDLING OF GASOLINE  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Mow up and down slopes (15° Max), not across.  
Be alert and turn machine off if a child enters the  
area.  
Choose a low ground speed so that you will not have  
to stop or shift while on the slope.  
To avoid personal injury or property damage, use extreme  
care in handling gasoline.Gasoline is extremely flammable  
and the vapors are explosive.  
Extinguish all cigarettes, cigars, pipes, and other  
sources of ignition.  
Use only approved gasoline container.  
Never remove gas cap or add fuel with the engine run-  
ning. Allow engine to cool before refueling.  
Never fuel the machine indoors.  
Never store the machine or fuel container where there  
is an open flame, spark, or pilot light such as on a water  
heater or other appliances.  
Never fill containers inside a vehicle or on a truck or  
trailer bed with plastic liner. Always place containers  
on the ground away from your vehicle when filling.  
Removegas-poweredequipmentfromthetruckortrailer  
and refuel it on the ground. If this is not possible, then  
refuel such equipment with a portable container, rather  
than from a gasoline dispenser nozzle.  
Keep the nozzle in contact with the rim of the fuel tank  
orcontaineropeningatalltimesuntilfuelingiscomplete.  
Do not use a nozzle lock-open device.  
Avoid starting, stopping, or turning on a slope. If the  
tires lose traction, disengage the blades and proceed  
slowly straight down the slope.  
If machine stops while going uphill, disengage blades,  
shift into reverse and back down slowly.  
If fuel is spilled on clothing, change clothing immedi-  
ately.  
Never overfill fuel tank. Replace gas cap and tighten  
securely.  
Do not turn on slopes unless necessary, and then, turn  
slowly and gradually downhill, if possible.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONGRATULATIONS on your purchase of a new tractor.  
Ithasbeendesigned,engineeredandmanufacturedtogive  
you the best possible dependability and performance.  
PRODUCT SPECIFICATIONS  
Gasoline Capacity  
and type:  
1.25 Gallons  
Unleaded Regular  
Shouldyouexperienceanyproblemyoucannoteasilyrem-  
edy,pleasecontactyournearestauthorizedservicecenter/  
department. We have competent, well-trained technicians  
and the proper tools to service or repair this tractor.  
Oil Type  
(API-SG-SL):  
SAE 30 (above 32°F)  
SAE 5W-30 (below 32°F)  
Oil Capacity:  
3 Pints  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your tractor properly.  
Always observe the “SAFETY RULES”.  
Spark Plug:  
(Gap: .030")  
Champion RC12YC  
Ground Speed (MPH):  
Forward:  
1st  
2nd  
1.1  
2.2  
3.3  
4.9  
1.4  
CUSTOMER RESPONSIBILITIES  
3rd  
Read and observe the safety rules.  
4th  
Reverse:  
Follow a regular schedule in maintaining, caring for  
and using your tractor.  
Tire Pressure:  
Charging System:  
Battery:  
Front:  
Rear:  
14 PSI  
12 PSI  
Follow the instructions underMaintenanceandStor-  
age” sections of this owner’s manual.  
3 Amps Battery  
5 Amps Headlights  
AMP/HR:  
MIN. CCA:  
Case Size:  
28  
230  
U1R  
WARNING: This tractor is equipped with an internal com-  
bustion engine and should not be used on or near any  
unimprovedforest-covered,brush-coveredorgrass-covered  
land unless the engine’s exhaust system is equipped with  
a spark arrester meeting applicable local or state laws (if  
any). If a spark arrester is used, it should be maintained  
in effective working order by the operator.  
Blade Bolt Torque:  
27-35 FT. LBS.  
A spark arrester for the muffler is available through your  
nearestauthorizedservicecenter/department (SeeREPAIR  
PARTS section of this manual).  
TABLE OF CONTENTS  
SAFETY RULES .........................................................2-3  
PRODUCT SPECIFICATIONS....................................... 4  
CUSTOMER RESPONSIBILITIES................................. 4  
ASSEMBLY.................................................................6-8  
OPERATION .............................................................9-13  
MAINTENANCE SCHEDULE ...................................... 14  
MAINTENANCE .....................................................14-17  
SERVICE AND ADJUSTMENTS ............................18-22  
STORAGE.................................................................... 23  
TROUBLESHOOTING ............................................24-25  
REPAIR PARTS ......................................................28-41  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
UNASSEMBLED PARTS  
Steering Wheel  
Seat  
(1) Washer  
17/32 x 1-3/16 x 12 Gauge  
(1) Lock  
Washer 1/2  
Steering Wheel  
Insert  
Steering  
Boot  
Steering  
Extension  
Shaft  
(1) Bolt  
Steering Wheel  
Adapter  
(1) Oil Drain Tube  
For Future Use  
Keys  
(2) Keys  
Slope Sheet  
(1) Locknut 1/2-20  
(1) Locknut 1/4-28  
(1) Large Flat Washer  
(1) Hex Bolt 1/4-28 x 1-1/4  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.  
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use  
the correct tools as necessary to insure proper tightness.  
TOOLS REQUIRED FOR ASSEMBLY  
A socket wrench set will make assembly easier. Standard  
wrench sizes are listed.  
INSERT  
1/2 HEX NUT  
(2) 7/16" wrenches  
(1) 3/4" wrench  
Utility knife  
Pliers  
Tire pressure gauge  
LARGE FLAT  
WASHER  
Whenrightorlefthandismentionedinthismanual,itmeans  
when you are in the operating position (seated behind the  
steering wheel).  
STEERING  
WHEEL  
STEERING  
BOOT  
TO REMOVE TRACTOR FROM  
CARTON  
TABS  
UNPACK CARTON  
Remove all accessible loose parts and parts cartons  
from carton.  
Cut along dotted lines on all four panels of carton.  
Remove end panels and lay side panels flat.  
Check for any additional loose parts or cartons and  
remove.  
ADAPTER  
EXTENSION SHAFT  
1/4 HEX BOLT  
1/4 LOCKNUT  
BEFORE REMOVING TRACTOR FROM  
SKID  
LOWER  
STEERING  
SHAFT  
ATTACH STEERING WHEEL (See Fig. 1)  
ASSEMBLE EXTENSION SHAFT AND BOOT  
TAB  
SLOTS  
Slide extension shaft onto lower steering shaft. Align  
mountingholesinextensionandlowershaftsandinstall  
1/4 hex bolt and locknut. Tighten securely.  
IMPORTANT:TIGHTEN BOLT AND NUT SECURELY TO 10-12  
FT. LBS TORQUE.  
FIG. 1  
Place tabs of steering boot over tab slots in dash and  
push down to secure.  
INSTALL STEERING WHEEL  
Position front wheels of the tractor so they are pointing  
straight forward.  
Remove steering wheel adapter from steering wheel  
and slide adapter onto steering shaft extension.  
Position steering wheel so cross bars are horizontal  
(left to right) and slide inside boot and onto adapter.  
Assemble large flat washer, 1/2 hex nut and tighten  
securely.  
Snap steering wheel insert into center of steering  
wheel.  
Remove protective materials from tractor hood and  
grill.  
IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES  
IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR  
IS TO ROLL OFF SKID.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
HOW TO SET UPYOUR TRACTOR  
INSTALL SEAT (See Fig. 2)  
SEAT PAN  
Adjust seat before tightening adjustment bolt.  
LABEL  
Remove adjustment bolt, lock washer and flat washer  
securing seat to cardboard packing and set aside for  
assembly of seat to tractor.  
Pivotseatupwardandremovefromthecardboardpack-  
ing. Remove the cardboard packing and discard.  
Place seat on seat pan so head of shoulder bolt is  
positioned over large slotted hole in pan.  
Push down on seat to engage shoulder bolt in slot and  
pull seat towards rear of tractor.  
Pivot seat and pan forward and assemble adjust-  
ment bolt, lockwasher and flat washer loosely. Do not  
tighten  
02602  
FIG. 3  
NOTE: You may now roll or drive your tractor off the skid.  
Follow the appropriate instruction below to remove the  
tractor from the skid.  
Lower seat into operating position and sit on seat.  
TO ROLL TRACTOR OFF SKID (See  
Operation section for location and function  
of controls)  
Slide seat until a comfortable position is reached  
which allows you to press clutch/brake pedal all the  
way down.  
Get off seat without moving its adjusted position.  
Raise seat and tighten adjustment bolt securely.  
Press lift lever plunger and raise attachment lift lever  
to its highest position.  
Release parking brake by depressing clutch/brake  
pedal.  
Place gearshift lever in neutral (N) position.  
Roll tractor forward off skid.  
Remove banding holding deflector shield up against  
tractor.  
SEAT  
TO DRIVE TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
WARNING: Beforestarting, read, understandandfollow  
all instructions in the Operation section of this manual. Be  
sure tractor is in a well-ventilated area. Be sure the area in  
front of tractor is clear of other people and objects.  
SEAT PAN  
SHOULDER  
BOLT  
Be sure all the above assembly steps have been com-  
pleted.  
FLAT WASHER  
LOCK WASHER  
Check engine oil level and fill fuel tank with gasoline.  
Sit on seat in operating position, depress clutch/brake  
pedal and set the parking brake.  
Place gear shift lever in neutral (N) position.  
Press lift lever plunger and raise attachment lift lever  
to its highest position.  
ADJUSTMENT  
BOLT  
02465  
Starttheengine.Afterenginehasstarted,movethrottle  
control to idle position.  
Depress clutch/brake pedal into full "BRAKE" position  
and hold. Move gearshift lever to 1st gear.  
Slowly release clutch/brake pedal and slowly drive  
tractor off skid.  
Applybraketostoptractor, setparkingbrakeandplace  
gearshift lever in neutral position.  
FIG. 2  
CHECK BATTERY (See Fig. 3)  
Lift seat pan to raised position.  
If this battery is put into service after month and year  
indicated on label (label located between terminals)  
charge battery for minimum of one hour at 6-10 amps.  
(See “BATTERY” in the Maintenance section of this  
manual for charging instructions).  
Turn ignition key to "OFF" position.  
Continue with the instructions that follow.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
CHECK TIRE PRESSURE  
The tires on your tractor were overinflated at the factory  
for shipping purposes. Correct tire pressure is important  
for best cutting performance.  
CHECKLIST  
BEFOREYOUOPERATEANDENJOYYOURNEW TRAC-  
TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE  
BESTPERFORMANCEANDSATISFACTIONFROMTHIS  
QUALITY PRODUCT.  
Reduce tire pressure to PSI shown in “PRODUCT  
SPECIFICATIONS” section of this manual.  
PLEASE REVIEW THE FOLLOWING CHECKLIST:  
All assembly instructions have been completed.  
No remaining loose parts in carton.  
Battery is properly prepared and charged. (Minimum  
1 hour at 6 amps).  
Seat is adjusted comfortably and tightened securely.  
All tires are properly inflated. (For shipping purposes,  
the tires were overinflated at the factory).  
Be sure mower deck is properly leveled side-to-side/  
front-to-rear for best cutting results. (Tires must be  
properly inflated for leveling).  
Check mower and drive belts. Be sure they are routed  
properly around pulleys and inside all belt keepers.  
CHECK DECK LEVELNESS  
For best cutting results, mower housing should be properly  
leveled. SeeTOLEVELMOWERHOUSINGintheService  
and Adjustments section of this manual.  
CHECK FOR PROPER POSITION OF ALL  
BELTS  
See the figures that are shown for replacing motion and  
mower blade drive belts in the Service and Adjustments  
section of this manual. Verify that the belts are routed  
correctly.  
Check wiring. See that all connections are still secure  
and wires are properly clamped.  
CHECK BRAKE SYSTEM  
Afteryoulearnhowtooperateyourtractor,checktoseethat  
the brake is properly adjusted. See “TO ADJUST BRAKE”  
in the Service and Adjustments section of this manual.  
WHILE LEARNING HOW TO USEYOUR TRACTOR, PAY  
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT  
ITEMS:  
Engine oil is at proper level.  
Fuel tank is filled with fresh, clean, regular unleaded  
gasoline.  
Become familiar with all controls - their location and  
function. Operate them before you start the engine.  
Be sure brake system is in safe operating condition.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.  
IGNITION  
FAST  
SLOW  
REVERSE  
HIGH  
LOW  
NEUTRAL  
CHOKE  
P
LIGHTS ON  
ENGINE START  
ENGINE ON  
PARKING BRAKE  
PARKING BRAKE PARKING BRAKE  
ENGINE OFF  
LOCKED  
UNLOCKED  
OIL PRESSURE  
BATTERY  
REVERSE  
FUEL  
FORWARD  
OVER TEMP  
LIGHT  
MOWER HEIGHT  
MOWER LIFT  
15  
15  
ATTACHMENT  
CLUTCH ENGAGED  
ATTACHMENT  
CLUTCH DISENGAGED  
SLOPE HAZARDS  
KEEP AREA CLEAR  
(SEE SAFETY RULES SECTION)  
DANGER, KEEP HANDS  
AND FEET AWAY  
DANGER indicates a hazard which, if not avoided,  
will result in death or serious injury.  
WARNING indicates a hazard which, if not avoided,  
could result in death or serious injury.  
FREE WHEEL  
(Automatic Models only)  
CAUTION indicates a hazard which, if not avoided,  
might result in minor or moderate injury.  
CAUTION when used without the alert symbol,  
indicates a situation that could result in damage  
to the tractor and/or engine.  
Failure to follow instructions  
could result in serious injury or  
death. The safety alert symbol  
is used to identify safety inform-  
ation about hazards which can  
result in death, serious injury  
and/or property damage.  
HOT SURFACES indicates a hazard which,  
if not avoided, could result in death, serious injury  
and/or property damage.  
FIRE indicates a hazard which, if not avoided,  
could result in death, serious injury and/or  
property damage.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOWYOUR TRACTOR  
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATINGYOUR TRACTOR  
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.  
Save this manual for future reference.  
ATTACHMENT  
IGNITION  
CLUTCH LEVER  
SWITCH  
THROTTLE/CHOKE CONTROL  
LIFT LEVER PLUNGER  
CLUTCH/BRAKE PEDAL  
ATTACHMENT  
LIFT LEVER  
MOWER DECK  
HEIGHT ADJUSTMENT  
POSITIONS  
PARKING BRAKE  
GEARSHIFT  
LEVER  
02629  
FIG. 4  
Our tractors conform to the safety standards of the American National Standards Institute.  
ATTACHMENT CLUTCH LEVER - Used to engage the  
mower blades, or other attachments mounted to your  
tractor.  
THROTTLE/CHOKE CONTROL - Used for starting and  
controlling engine speed.  
GEARSHIFT LEVER - Selects the speed and direction  
of tractor.  
ATTACHMENT LIFT LEVER - Used to raise, lower, and  
adjust the mower deck or other attachments mounted to  
your tractor.  
CLUTCH/BRAKEPEDAL-Usedfordeclutchingandbrak-  
ing the tractor and starting the engine.  
PARKING BRAKE - Locks clutch/brake pedal into the  
brake position.  
LIFT LEVER PLUNGER - Used to release attachment lift  
lever when changing its position.  
IGNITION SWITCH - Used for starting and stopping the  
engine.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any tractor can result in foreign objects thrown into the eyes, which can  
result in severe eye damage. Always wear safety glasses or eye shields while operating your  
tractor or performing any adjustments or repairs. We recommend a wide vision safety mask  
over spectacles or standard safety glasses.  
00155  
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY  
POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY  
TO BE DISCHARGED, (DEAD).  
HOW TO USEYOUR TRACTOR  
TO SET PARKING BRAKE (See Fig. 5)  
NOTE: Under certain conditions when tractor is standing  
idlewiththeenginerunning, hotengineexhaustgasesmay  
cause “browning” of grass. To eliminate this possibility, al-  
ways stop engine when stopping tractor on grass areas.  
Your tractor is equipped with an operator presence sens-  
ing switch. When engine is running, any attempt by the  
operator to leave the seat without first setting the parking  
brake will shut off the engine.  
Depress clutch/brake pedal into full “BRAKE” position  
and hold.  
Place parking brake lever inENGAGEDposition and  
releasepressurefromclutch/brakepedal. Pedalshould  
remain in “BRAKE” position. Make sure parking brake  
will hold tractor secure.  
CAUTION: Always stop tractor com-  
pletely, as described above, before  
leaving the operator's position; to  
empty grass catcher, etc.  
TO USE THROTTLE CONTROL (See Fig. 5)  
Always operate engine at full throttle.  
ATTACHMENT CLUTCH LEVER  
"ENGAGED" POSITION  
Operating engine at less than full throttle reduces the  
battery charging rate.  
Full throttle offers the best bagging and mower perfor-  
mance.  
THROTTLE/CHOKE  
CONTROL LEVER  
IGNITION KEY  
"DISENGAGED"  
TO MOVE FORWARD AND BACKWARD  
(See Fig. 5)  
The direction and speed of movement is controlled by the  
gearshift lever.  
POSITION  
"BRAKE"  
POSITION  
PARKING BRAKE  
"ENGAGED"  
POSITION  
Start tractor with clutch/brake pedal depressed and  
gearshift lever in neutral (N) position.  
Move gearshift lever to desired position.  
Slowly release clutch/brake pedal to start move-  
ment.  
GEARSHIFT  
LEVER  
IMPORTANT: BRING TRACTOR TO A COMPLETE STOP  
BEFORE SHIFTING OR CHANGING GEARS. FAILURE  
TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR  
TRANSAXLE.  
PARKING BRAKE  
"DISENGAGED" POSITION  
CLUTCH/BRAKE PEDAL  
"DRIVE" POSITION  
FIG.5  
TO ADJUST MOWER CUTTING HEIGHT  
(See Fig. 5)  
The position of the attachment lift lever determines the  
cutting height.  
STOPPING (See Fig. 5)  
MOWER BLADES -  
To stop mower blades,move attachment clutch lever  
to “DISENGAGED” position.  
Grasp lift lever.  
Press plunger with thumb and move lever to desired  
position.  
GROUND DRIVE -  
To stop ground drive, depress clutch/brake pedal into  
full “BRAKE” position.  
Move gearshift lever to neutral (N) position.  
The cutting height range is approximately 1-1/2 to 4".  
The heights are measured from the ground to the blade tip  
withtheenginenotrunning. Theseheightsareapproximate  
and may vary depending upon soil conditions, height of  
grass and types of grass being mowed.  
ENGINE -  
Move throttle control between half and full speed (fast)  
position.  
The average lawn should be cut to approximately 2-1/2  
inches during the cool season and to over 3 inches  
during hot months. For healthier and better looking  
lawns, mow often and after moderate growth.  
NOTE: Failure to move throttle control between half and  
fullspeed(fast)position,beforestoppingmaycauseengine  
to “backfire”.  
For best cutting performance, grass over 6 inches  
in height should be mowed twice. Make the first cut  
relatively high; the second to desired height.  
Turn ignition key to “STOP” position and remove key.  
Always remove key when leaving tractor to prevent  
unauthorized use.  
Never use choke to stop engine.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
Torestartmovement, slowlyreleaseparkingbrakeand  
TO OPERATE MOWER (See Fig. 6)  
clutch/brake pedal.  
Yourtractor isequippedwithanoperatorpresencesensing  
switch. Any attempt by the operator to leave the seat with  
the engine running and the attachment clutch engaged  
will shut off the engine.You must remain fully and centrally  
positioned in the seat to prevent the engine from hesitating  
or cutting off when operating your equipment on rough,  
rolling terrain or hills.  
Make all turns slowly.  
TO TRANSPORT  
Raiseattachmentlifttohighestpositionwithattachment  
lift control.  
When pushing or towing your tractor, be sure gearshift  
lever is in neutral (N) position.  
Select desired height of cut.  
Start mower blades by engaging attachment clutch  
control.  
Do not push or tow tractor at more than five (5) MPH.  
NOTE: To protect hood from damage when transporting  
your tractor on a truck or a trailer, be sure hood is closed  
and secured to tractor. Use an appropriate means of tying  
hood to tractor (rope, cord, etc.).  
TO STOP MOWER BLADES - disengage attachment  
clutch control.  
CAUTION: Do not operate the mower  
without either the entire grass catcher,  
onmowerssoequipped,orthedeflector  
shield in place.  
TOWING CARTS AND OTHER ATTACH-  
MENTS  
Tow only the attachments that are recommended by and  
comply with specifications of the manufacturer of your trac-  
tor. Use common sense when towing.Too heavy of a load,  
while on a slope, is dangerous.Tires can lose traction with  
the ground and cause you to lose control of your tractor.  
ATTACHMENT LIFT  
LEVER HIGH  
POSITION  
"ENGAGED"  
POSITION  
BEFORE STARTING THE ENGINE  
CHECK ENGINE OIL LEVEL  
LOW  
POSITION  
The engine in your tractor has been shipped, from the  
factory, already filled with summer weight oil.  
Check engine oil with tractor on level ground.  
Remove oil fill cap/dipstick and wipe clean, reinsert the  
dipstick and screw cap tight, wait for a few seconds,  
remove and read oil level. If necessary, add oil until  
“FULLmark on dipstick is reached. Do not overfill.  
ATTACHMENT  
CLUTCH LEVER  
"DISENGAGED"  
POSITION  
For cold weather operation you should change oil for  
easier starting (See “OIL VISCOSITY CHART” in the  
Maintenance section of this manual).  
To change engine oil, see the Maintenance section in  
this manual.  
DEFLECTOR  
SHIELD  
ADD GASOLINE  
Fill fuel tank to bottom of filler neck. Do not overfill.  
Use fresh, clean, regular unleaded gasoline with a  
minimum of 87 octane. (Use of leaded gasoline will  
increase carbon and lead oxide deposits and reduce  
valve life). Do not mix oil with gasoline. Purchase fuel  
in quantities that can be used within 30 days to assure  
fuel freshness.  
FIG. 6  
TO OPERATE ON HILLS  
WARNING: Do not drive up or down  
hills with slopes greater than 15° and  
do not drive across any slope.  
CAUTION: Wipe off any spilled oil or  
fuel. Do not store, spill or use gasoline  
near an open flame.  
Choose the slowest speed before starting up or down  
hills.  
Avoid stopping or changing speed on hills.  
If slowing is necessary, move throttle control lever to  
slower position.  
If stopping is absolutely necessary, push clutch/brake  
pedal quickly to brake position and engage parking  
brake.  
IMPORTANT: WHEN OPERATING IN TEMPERATURES  
BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE  
GASOLINE TO HELP INSURE GOOD COLD WEATHER  
STARTING.  
Move gearshift lever to 1st gear. Be sure you have  
allowed room for tractor to roll slightly as you restart  
movement.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
MOWING TIPS  
CAUTION: Alcohol blended fuels (called gasohol or  
Tire chains cannot be used when the mower housing  
is attached to tractor.  
using ethanol or methanol) can attract moisture which  
leads to separation and formation of acids during stor-  
age. Acidicgascandamagethefuelsystemofanengine  
while in storage. To avoid engine problems, the fuel  
system should be emptied before storage of 30 days  
or longer. Drain the gas tank, start the engine and let  
it run until the fuel lines and carburetor are empty. Use  
fresh fuel next season. See Storage Instructions for  
additional information. Never use engine or carburetor  
cleaner products in the fuel tank or permanent damage  
may occur.  
Mower should be properly leveled for best mowing per-  
formance. SeeTO LEVEL MOWER HOUSINGin the  
Service and Adjustments section of this manual.  
The left hand side of mower should be used for trim-  
ming.  
Drive so that clippings are discharged onto the area  
that has been cut. Have the cut area to the right of the  
machine. This will result in a more even distribution of  
clippings and more uniform cutting.  
Whenmowinglargeareas,startbyturningtotherightso  
that clippings will discharge away from shrubs, fences,  
driveways, etc. After one or two rounds, mow in the  
opposite direction making left hand turns until finished  
(See Fig. 7 ).  
TO START ENGINE (See Fig. 5)  
When starting the engine for the first time or if the engine  
has run out of fuel, it will take extra cranking time to move  
fuel from the tank to the engine.  
Sit on seat in operating position, depress clutch/brake  
pedal and set parking brake.  
Place gear shift lever in neutral (N) position.  
Move attachment clutch to “DISENGAGED” position.  
Move throttle control to choke position.  
NOTE: Before starting, read the warm and cold starting  
procedures below.  
InsertkeyintoignitionandturnkeyclockwisetoSTART”  
position and release key as soon as engine starts.  
Do not run starter continuously for more than fifteen  
seconds per minute. If the engine does not start after  
several attempts, move throttle control to fast position,  
wait a few minutes and try again. If engine still does  
not start, move the throttle control back to the choke  
position and retry.  
00272  
FIG. 7  
If grass is extremely tall, it should be mowed twice to  
reduce load and possible fire hazard from dried clip-  
pings. Make first cut relatively high; the second to the  
desired height.  
WARM WEATHER STARTING (50° F and above)  
When engine starts, move the throttle control to the  
fast position.  
Do not mow grass when it is wet. Wet grass will plug  
mower and leave undesirable clumps. Allow grass to  
dry before mowing.  
Always operate engine at full throttle when mow-  
ing to assure better mowing performance and proper  
discharge of material. Regulate ground speed by se-  
lecting a low enough gear to give the mower cutting  
performance as well as the quality of cut desired.  
The attachments and ground drive can now be used.If  
the engine does not accept the load, restart the engine  
and allow it to warm up for one minute using the choke  
as described above.  
COLD WEATHER STARTING ( 50° F and below)  
When engine starts, allow engine to run with the  
throttle control in the choke position until the engine  
runs roughly, then move throttle control to fast posi-  
tion.This may require an engine warm-up period from  
several seconds to several minutes, depending on the  
temperature.  
When operating attachments, select a ground speed  
that will suit the terrain and give best performance of  
the attachment being used.  
The attachments can also be used during the engine  
warm-up period.  
NOTE: If at a high altitude (above 3000 feet) or in cold  
temperatures (below 32 F) the carburetor fuel mixture may  
need to be adjusted for best engine performance. See “TO  
ADJUST CARBURETOR” in the Service and Adjustments  
section of this manual.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
MAINTENANCE SCHEDULE  
USE  
HOURS  
HOURS  
FILL IN DATES  
HOURSHOURS  
50 100  
STORAGE  
EACH  
8
25  
SEASON  
AS YOU COMPLETE  
REGULAR SERVICE  
BEFORE SERVICE DATES  
EVERY EVERY EVERY EVERY EVERY  
BEFORE  
Check Brake Operation  
Check Tire Pressure  
Check Operator Presence and  
Interlock Systems  
T
Check for Loose Fasteners  
R
5
A
Sharpen/Replace Mower Blades  
3
C
Lubrication Chart  
T
Check Battery Level  
4
0
Clean Battery and Terminals  
R
Check Transaxle Cooling  
Check V-Belts  
Check Engine Oil Level  
Change Engine Oil (with oil filter)  
1,2  
Change Engine Oil (without oil filter)  
1,2  
E
Clean Air Filter  
N
2
2
G
Clean Air Screen  
I
Inspect Muffler/Spark Arrester  
N
Replace Oil Filter (If equipped)  
1,  
2
2
E
Clean Engine Cooling Fins  
Replace Spark Plug  
Replace Air Filter Paper Cartridge  
Replace Fuel Filter  
2
3 - Replace blades more often when mowing in sandy soil.  
4 - Not required if equipped with maintenance-free battery.  
5 - Tighten front axle pivot bolt to 35 ft.-lbs. maximum.  
Do not overtighten.  
1 - Change more often when operating under a heavy load or  
in high ambient temperatures.  
2 - Service more often when operating in dirty or dusty conditions.  
LUBRICATION CHART  
GENERAL RECOMMENDATIONS  
SPINDLE ZERK  
SPINDLE  
The warranty on this tractor does not cover items that have  
beensubjectedtooperatorabuseornegligence. Toreceive  
full value from the warranty, operator must maintain tractor  
as instructed in this manual.  
ZERK  
FRONT  
WHEEL BEARING  
ZERK  
FRONT  
WHEEL  
BEARING  
ZERK  
Some adjustments will need to be made periodically to  
properly maintain your tractor.  
ENGINE  
At least once a season, check to see if you should make  
any of the adjustments described in the Service and  
Adjustments section of this manual.  
• At least once a year you should replace the spark plug,  
clean or replace air filter, and check blades and belts  
for wear. A new spark plug and clean air filter assure  
proper air-fuel mixture and help your engine run better  
and last longer.  
GEARSHIFT  
PIVOTS  
01961  
BEFORE EACH USE  
SAE 30 OR 10W30 MOTOR OIL  
GENERAL PURPOSE GREASE  
Check engine oil level.  
Check brake operation.  
Check tire pressure.  
Check operator presence and  
interlock systems for proper operation.  
Check for loose fasteners.  
REFER TO MAINTENANCE “ENGINE” SECTION  
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS  
WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS  
LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL  
SHORTENTHELIFEOFTHESELF-LUBRICATINGBEARINGS.  
IFYOU FEELTHEY MUST BE LUBRICATED, USE ONLY A DRY,  
POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
TRACTOR  
MANDREL  
ASSEMBLY  
TRAILING  
EDGE UP  
Always observe safety rules when performing any main-  
tenance.  
CENTER  
HOLE  
BRAKE OPERATION  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be checked and adjusted.  
LOCK WASHER  
TIRES  
STAR  
Maintainproperairpressureinalltires(SeePRODUCT  
SPECIFICATIONS” section of this manual).  
FLAT WASHER  
BLADE  
Keep tires free of gasoline, oil, or insect control chemi-  
cals which can harm rubber.  
Avoid stumps, stones, deep ruts, sharp objects and  
other hazards that may cause tire damage.  
BLADE BOLT  
FIG. 8  
NOTE: To seal tire punctures and prevent flat tires due to  
slow leaks, tire sealant may be purchased from your local  
parts dealer. Tire sealant also prevents tire dry rot and  
corrosion.  
TO SHARPEN BLADE (See Fig. 9)  
NOTE: We do not recommend sharpening blade - but if  
you do, be sure the blade is balanced.  
Care should be taken to keep the blade balanced. An un-  
balancedbladewillcauseexcessivevibrationandeventual  
damage to mower and engine.  
OPERATOR PRESENCE SYSTEM  
Besureoperatorpresenceandinterlocksystemsarework-  
ing properly. If your tractor does not function as described,  
repair the problem immediately.  
The blade can be sharpened with a file or on a grind-  
ing wheel. Do not attempt to sharpen while on the  
mower.  
The engine should not start unless the clutch/brake  
pedalisfullydepressedandattachementclutchcontrol  
is in the disengaged position.  
Whentheengineisrunning,anyattemptbytheoperator  
to leave the seat without first setting the parking brake  
should shut off the engine.  
When the engine is running and the attachment clutch  
is engaged, any attempt by the operator to leave the  
seat should shut off the engine.  
The attachment clutch should never operate unless  
the operator is in the seat.  
To check blade balance, you will need a 5/8" diameter  
steel bolt, pin, or a cone balancer. (When using a  
cone balancer, follow the instructions supplied with  
balancer.)  
NOTE: Do not use a nail for balancing blade. The lobes of  
the center hole may appear to be centered, but are not.  
Slidebladeontoanunthreadedportionofthesteelbolt  
or pin and hold the bolt or pin parallel with the ground.  
If blade is balanced, it should remain in a horizontal  
position. If either end of the blade moves downward,  
sharpen the heavy end until the blade is balanced.  
BLADE CARE  
Forbestresultsmowerbladesmustbekeptsharp. Replace  
bent or damaged blades.  
CENTER HOLE  
BLADE REMOVAL (See Fig. 8)  
Raise mower to highest position to allow access to  
blades.  
Removebladebolt,lockwasherandatwashersecuring  
blade.  
Install new or resharpened blade with trailing edge up  
towards deck as shown.  
5/8" BOLT  
OR PIN  
BLADE  
IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER  
HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL  
ASSEMBLY.  
FIG. 9  
Reassemble blade bolt, lock washer and flat washer  
in exact order as shown.  
Tighten blade bolt securely (27-35 Ft. Lbs. torque).  
IMPORTANT: BLADEBOLTISHEATTREATED.IFBOLTNEEDS  
REPLACING, REPLACE ONLYWITH APPROVE BOLT SHOWN  
IN THE REPAIR PARTS.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
Change the oil after every 25 hours of operation or at least  
once a year if the tractor is not used for 25 hours in one  
year.  
BATTERY  
Yourtractorhasabatterychargingsystemwhichissufficient  
for normal use. However, periodic charging of the battery  
with an automotive charger will extend its life.  
Check the crankcase oil level before starting the engine  
and after each eight (8) hours of operation. Tighten oil fill  
cap/dipstick securely each time you check the oil level.  
Keep battery and terminals clean.  
Keep battery bolts tight.  
Keep small vent holes open.  
Recharge at 6-10 amperes for 1 hour.  
TO CHANGE ENGINE OIL (See Figs. 10 and 11)  
Determine temperature range expected before oil change.  
All oil must meet API service classification SG-SL.  
NOTE: The original equipment battery on your tractor is  
maintenance free. Do not attempt to open or remove caps  
or covers. Adding or checking level of electrolyte is not  
necessary.  
Be sure tractor is on level surface.  
Oil will drain more freely when warm.  
Catch oil in a suitable container.  
Remove oil fill cap/dipstick. Be careful not to allow dirt  
to enter the engine when changing oil.  
TO CLEAN BATTERY AND TERMINALS  
Corrosion and dirt on the battery and terminals can cause  
the battery to “leak” power.  
Remove yellow cap from end of drain valve and install  
the drain tube onto the fitting.  
Disconnect BLACK battery cable first then RED bat-  
tery cable and remove battery from tractor.  
OIL DRAIN VALVE  
Rinse the battery with plain water and dry.  
Cleanterminalsandbatterycableendswithwirebrush  
until bright.  
CLOSED AND  
LOCKED  
POSITION  
Coat terminals with grease or petroleum jelly.  
Reinstall battery (See “REPLACING BATTERY” in  
the SERVICE AND ADJUSTMENTS section of this  
manual).  
YELLOW CAP  
DRAIN  
V-BELTS  
TUBE  
Check V-belts for deterioration and wear after 100 hours  
of operation and replace if necessary. The belts are not  
adjustable. Replace belts if they begin to slip from wear.  
FIG. 11  
TRANSAXLE COOLING  
Keep transaxle free from build-up of dirt and chaff which  
can restrict cooling.  
Unlock drain valve by pushing inward and turning  
counterclockwise.  
To open, pull out on the drain valve.  
After oil has drained completely, close and lock the  
drain valve by pushing inward and turning clockwise  
until the pin is in the locked position as shown.  
Remove the drain tube and replace the cap onto to the  
bottom fitting of the drain valve.  
Refill engine with oil through oil fill dipstick tube. Pour  
slowly. Do not overfill. For approximate capacity see  
“PRODUCT SPECIFICATIONS” section of this man-  
ual.  
ENGINE  
LUBRICATION  
Only use high quality detergent oil rated with API service  
classification SG-SL. Select the oil’s SAE viscosity grade  
according to your expected operating temperature.  
SAE VISCOSITY GRADES  
Use gauge on oil fill cap/dipstick for checking level.  
Be sure dipstick cap is tightened securely for accurate  
reading. Keep oil at “FULLline on dipstick.  
SAE 30  
5W-30  
-20  
0
30  
32 40  
0
100  
60  
80  
F
CLEAN AIR SCREEN  
C
-20  
10  
-30  
-10  
20  
30  
40  
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE  
Air screen must be kept free of dirt and chaff to prevent  
engine damage from overheating. Clean with a wire brush  
or compressed air to remove dirt and stubborn dried gum  
fibers.  
oil_visc_chart1_e  
FIG. 10  
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)  
improvestartingincoldweather,theywillresultinincreased  
oilconsumptionwhenusedabove3F. Checkyourengine  
oil level more frequently to avoid possible engine damage  
from running low on oil.  
ENGINE COOLING SYSTEM (See Fig. 12)  
Debris may clog the engine's air cooling system. Remove  
blower housing and clean the area shown to prevent over-  
heating and engine damage.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
AIR SCREEN  
MUFFLER  
CLEAN OUT CHAFF AND DEBRIS  
Inspect and replace corroded muffler and spark arrester  
(if equipped) as it could create a fire hazard and/or dam-  
age.  
SPARK PLUGS  
Replace spark plugs at the beginning of each mowing  
season or after every 100 hours of operation, whichever  
occurs first. Spark plug type and gap setting are shown in  
“PRODUCT SPECIFICATIONS” section of this manual.  
02744  
IN-LINE FUEL FILTER (See Fig. 14)  
The fuel filter should be replaced once each season. If fuel  
filter becomes clogged, obstructing fuel flow to carburetor,  
replacement is required.  
FIG. 12  
AIR FILTER (See Fig. 13)  
With engine cool, remove filter and plug fuel line sec-  
tions.  
Place new fuel filter in position in fuel line with arrow  
pointing towards carburetor.  
Be sure there are no fuel line leaks and clamps are  
properly positioned.  
Immediately wipe up any spilled gasoline.  
Your engine will not run properly using a dirty air filter.  
Replace pre-cleaner after every 25 hours of operation or  
every season. Service paper cartridge every 100 hours of  
operation or every season, whichever occurs first.  
Service air cleaner more often under dusty conditions.  
Pull up on air filter cover handle and rotate towards  
engine.  
Remove cover.  
Carefully remove air filter cartridge and pre-cleaner  
from base.  
CLAMP  
Clean base carefully to prevent debris from falling into  
carburetor.  
CLAMP  
NOTE: If very dirty or damaged, replace cartridge.  
Place new pre-cleaner and cartridge firmly in base.  
Align tabs on cover with slots in blower housing and  
replace cover.  
Hook handle on cover and push down on handle to  
close.  
FUEL  
FILTER  
IMPORTANT: Petroleum solvents, such as kerosene, are  
not to be used to clean the cartridge. They may cause  
deterioration of the cartridge. Do not oil cartridge. Do not  
use pressurized air to clean cartridge.  
FIG. 14  
CLEANING  
Clean engine, battery, seat, finish, etc. of all foreign  
matter.  
Keep finished surfaces and wheels free of all gasoline,  
oil, etc.  
HANDLE  
Protect painted surfaces with automotive type wax.  
COVER  
We do not recommend using a garden hose or pressure  
washer to clean your tractor unless the engine and trans-  
mission are covered to keep water out. Water in engine or  
transmission will shorten the useful life of your tractor. Use  
compressed air or a leaf blower to remove grass, leaves  
and trash from tractor and mower.  
CARTRIDGE  
PRE-CLEANER  
TABS  
BASE  
SLOTS  
FIG. 13  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST-  
MENTS:  
Depress clutch/brake pedal fully and set parking brake.  
Place gearshift lever in neutral (N) position.  
Place attachment clutch in “DISENGAGED” position.  
Turn ignition key to “STOP” and remove key.  
Make sure the blades and all moving parts have completely stopped.  
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact  
with plug.  
Raise lift lever to raise suspension arms. Slide mower  
out from under tractor.  
TRACTOR  
TO REMOVE MOWER (See Fig. 15)  
Mower will be easier to remove from the right side of trac-  
tor.  
IMPORTANT:IFANATTACHMENTOTHERTHANTHEMOWER  
DECK ISTO BE MOUNTED ONTHETRACTOR, REMOVETHE  
FRONTLINKSANDHOOKTHECLUTCHSPRINGINTOSQUARE  
HOLE IN FRAME.  
Place attachment clutch in “DISENGAGED” position.  
Move attachment lift lever forward to lower mower to  
its lowest position.  
TO INSTALL MOWER (SEE FIG. 15)  
Raise attachment lift lever to its highest position.  
Slide mower under tractor with deflector shield to right  
side of tractor.  
Lower lift lever to its lowest position.  
Connect front links to mower deck and secure with  
retainer springs.  
Connect suspension arms to rear deck brackets and  
secure with retainer springs.  
Connect anti-swaybar to chassis bracket and secure  
with retainer spring.  
Roll belt off engine pulley.  
Removesmallretainerspring,andremoveclutchspring  
off pulley bolt.  
Remove large retainer spring, slide collar off and push  
housing guide out of bracket.  
Disconnect anti-swaybar from chassis bracket by re-  
moving retainer spring.  
Disconnect suspension arms from rear deck brackets  
by removing retainer springs.  
Disconnect front links from deck by removing retainer  
springs.  
SMALL RETAINER SPRING  
CLUTCH SPRING  
SQUARE HOLE  
FLAT WASHER  
SUSPENSION ARMS  
ENGINE PULLEY  
SMALL RETAINER SPRING  
CLUTCH SPRING  
FRONT LINK  
4
2
3
8
RETAINER SPRING  
RETAINER SPRINGS  
(BOTH SIDES)  
ANTI-SWAY BAR  
BRACKET  
COLLAR  
HOUSING GUIDE  
02694  
DEFLECTOR SHIELD  
LARGE RETAINER SPRING  
FIG. 15  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
Push clutch cable housing guide into bracket, slide col-  
FRONT-TO-BACK ADJUSTMENT (See Figs. 18 and 19)  
lar onto guide and secure with large retainer spring.  
IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE  
FOLLOWINGFRONT-TO-BACKADJUSTMENTISNECESSARY,  
BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO  
MOWER WILL STAY LEVEL SIDE-TO-SIDE.  
Place flat washer and clutch spring on idler pulley bolt  
and secure with small retainer spring.  
Install belt onto engine pulley.  
To obtain the best cutting results, the mower housing  
should be adjusted so that the front is approximately 1/8"  
to 1/2" lower than the rear when the mower is in its high-  
est position.  
TO LEVEL MOWER HOUSING  
Adjust the mower while tractor is parked on level ground  
or driveway. Make sure tires are properly inflated (See  
“PRODUCT SPECIFICATIONSsection of this manual). If  
tires are over or underinflated, you will not properly adjust  
your mower.  
Checkadjustmentonrightsideoftractor. Measuredistance  
“D” directly in front and behind the mandrel at bottom edge  
of mower housing as shown.  
Before making any necessary adjustments, check that  
both front links are equal in length.  
If links are not equal in length, adjust one link to same  
length as other link.  
To lower front of mower loosen nut “E” on both front  
links an equal number of turns.  
When distance “D” is 1/8" to 1/2" lower at front than  
rear, tighten nuts “F” against trunnion on both front  
links.  
SIDE-TO-SIDE ADJUSTMENT (See Figs. 16 and 17)  
Raise mower to its highest position.  
At the midpoint of both sides of mower, measure height  
from bottom edge of mower to ground. Distance “A”  
on both sides of mower should be the same or within  
1/4" of each other.  
If adjustment is necessary, make adjustment on one  
side of mower only.  
To raise one side of mower, tighten lift link adjustment  
nut on that side.  
To lower one side of mower, loosen lift link adjustment  
nut on that side.  
To raise front of mower, loosen nutFfrom trunnion on  
both front links. Tighten nut “E” on both front links an  
equal number of turns.The two front links must remain  
equal in length.  
WhendistanceDis1/8"to1/2"loweratfrontthanrear,  
tighten nut “F” against trunnion on both front links.  
Recheck side-to-side adjustment.  
NOTE: Threefullturnsofadjustmentnutwillchangemower  
height about 1/8".  
Recheck measurements after adjusting.  
BOTTOM EDGE OF  
BOTTOM EDGE  
OF MOWER  
MOWER  
MANDREL  
00598  
TO GROUND  
01268  
TO GROUND  
“A”  
“A”  
"D"  
"D"  
GROUND LINE  
FIG. 18  
FIG. 16  
BOTH FRONT LINKS MUST BE EQUAL IN LENGTH  
SUSPENSION ARM  
01267  
01553  
LIFT LINK  
ADJUSTMENT  
NUT  
FIG. 17  
NUT "F"  
NUT "E"  
TRUNNION  
FRONT LINKS  
FIG. 19  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REPLACE MOWER BLADE DRIVE BELT  
(See Fig. 20)  
The mower blade drive belt may be replaced without tools.  
Park the tractor on level surface. Engage parking brake.  
TO CHECK AND ADJUST BRAKE (See Fig. 21)  
Your tractor is equipped with an adjustable brake system  
which is mounted on the right side of the transaxle.  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be checked and adjusted.  
BELT REMOVAL -  
Remove mower from tractor (See “TO REMOVE  
MOWER” in this section of manual).  
TO CHECK BRAKE  
Park tractor on a level, dry concrete or paved surface,  
depress clutch/brake pedal all the way down and en-  
gage parking brake.  
Work belt off both mandrel pulleys and idler pulleys.  
Pull belt away from mower.  
BELT INSTALLATION -  
Place gear shift lever in neutral (N) position.  
Work belt around both mandrel pulleys and idler pul-  
Therearwheelsmustlockandskidwhenyoutrytomanually  
push the tractor forward.If the rear wheels rotate, the brake  
needs to be adjusted or the pads need to be replaced.  
leys.  
Make sure belt is in all pulley grooves and inside all  
belt guides.  
Install mower (See "To Install Mower" in this section of  
manual).  
TO ADJUST BRAKE  
Depress clutch/brake pedal all the way down and en-  
gage parking brake.  
Measure distance between brake operating arm and  
nut “A” on brake rod.  
If distance is other than 1-1/2", loosen jam nut and turn  
nut “A” until distance becomes 1-1/2". Retighten jam  
nut against nut “A”.  
IDLER  
PULLEYS  
MANDREL  
PULLEY  
Roadtesttractorforproperstoppingdistanceasstated  
above. Readjust if necessary. If stopping distance is  
still greater than five (5) feet in highest gear, further  
maintenance is necessary. Replace brake pads or  
contact a qualified service center.  
4 2  
3
8
WITH PARKING BRAKE “ENGAGED”  
1-1/2"  
NUT “A”  
MANDREL  
PULLEY  
JAM NUT  
OPERATING ARM  
FIG. 20  
FIG. 21  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REPLACE MOTION DRIVE BELT  
TO ADJUST STEERING WHEEL ALIGN-  
MENT  
If steering wheel crossbars are not horizontal (left to right)  
whenwheelsarepositionedstraightforward,removesteer-  
ing wheel and reassemble per instructions in the Assembly  
section of this manual.  
(See Fig. 22)  
Park the tractor on level surface. Engage parking brake.  
For assistance, there is a belt installation guide decal on  
bottom side of left footrest.  
BELT REMOVAL -  
Remove mower (See “TO REMOVE MOWER” in this  
section of manual).  
FRONT WHEEL TOE-IN/CAMBER  
The front wheel toe-in and camber are not adjustable on  
your tractor. If damage has occurred to affect the front  
wheel toe-in or camber, contact your nearest authorized  
service center/department.  
NOTE: Observe entire motion drive belt and position of all  
belt guides and keepers.  
Remove belt from stationary idler and clutching idler.  
Remove belt downward from around engine pulley.  
Pull belt slack toward rear of tractor. Remove belt  
upwards from transaxle pulley by deflecting belt keep-  
ers.  
Remove belt from center span keeper and pull belt  
away from tractor.  
TO REMOVE WHEEL FOR REPAIRS  
(See Fig. 23)  
Block up axle securely.  
Removeaxlecover, retainingringandwasherstoallow  
wheel removal (rear wheel contains a square key - Do  
not lose).  
BELT INSTALLATION -  
Carefully work new belt down between transaxle belt  
keepers and onto the input pulley.  
Slide belt into the center span keeper.  
Pull belt toward front of tractor and roll around the top  
groove of engine pulley.  
Repair tire and reassemble.  
On rear wheels only: align grooves in rear wheel hub  
and axle. Insert square key.  
Replace washers and snap retaining ring securely in  
axle groove.  
Replace axle cover.  
Install belt through stationary idler and clutching  
idler.  
Make sure belt is in all pulley grooves and inside all  
belt guides and keepers.  
Install mower (See “TO INSTALL MOWER” in this sec-  
tion of manual).  
NOTE: To seal tire punctures and prevent flat tires due to  
slow leaks, tire sealant may be purchased from your local  
parts dealer. Tire sealant also prevents tire dry rot and  
corrosion.  
ENGINE  
PULLEY  
WASHERS  
RETAINING RING  
CLUTCHING  
IDLER  
STATIONARY  
IDLER  
TRANSAXLE  
PULLEY  
AXLE COVER  
CENTER SPAN  
KEEPER  
SQUARE KEY (REAR  
WHEEL ONLY)  
FIG. 23  
00811  
FIG. 22  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO START ENGINE WITH A WEAK BATTERY  
(See Fig. 24)  
REPLACING BATTERY (See Figs. 25 and 26)  
WARNING: Do not short battery  
terminals by allowing a wrench or any  
other object to contact both terminals  
at the same time. Before connect-  
ing battery, remove metal bracelets,  
wristwatch bands, rings, etc.  
Positive terminal must be connected  
first to prevent sparking from acci-  
dental grounding.  
WARNING: Lead-acid batteries gen-  
erate explosive gases. Keep sparks,  
flameandsmokingmaterialsawayfrom  
batteries. Always wear eye protection  
when around batteries.  
If your battery is too weak to start the engine, it should be  
recharged. (See "BATTERY" in the MAINTENANCE sec-  
tion of this manual).  
Lift seat pan to raised position.  
DisconnectBLACKbatterycablerstthenREDbattery  
cable and carefully remove battery from tractor.  
If “jumper cables” are used for emergency starting, follow  
this procedure:  
IMPORTANT: YOURTRACTOR IS EQUIPPEDWITH A 12VOLT  
SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT  
SYSTEM. DO NOT USEYOUR TRACTOR BATTERY TO START  
OTHER VEHICLES.  
Install new battery with terminals in same position as  
old battery.  
First connect RED battery cable to positive (+) terminal  
with hex bolt and keps nut as shown.Tighten securely.  
Slide terminal cover over terminal.  
TO ATTACH JUMPER CABLES -  
Connect one end of the RED cable to the POSITIVE  
(+) terminal of each battery(A-B), taking care not to  
short against tractor chassis.  
Connect BLACK grounding cable to negative (-) ter-  
minal with remaining hex bolt and keps nut. Tighten  
securely.  
ConnectoneendoftheBLACKcabletotheNEGATIVE  
(-) terminal (C) of fully charged battery.  
Connect the other end of the BLACK cable (D) to good  
chassis ground, away from fuel tank and battery.  
SEAT PAN  
TO REMOVE CABLES, REVERSE ORDER -  
BLACK cable first from chassis and then from the fully  
charged battery.  
RED cable last from both batteries.  
02602  
FIG. 25  
KEPS  
NUT  
TERMINAL  
COVER  
02614  
WEAK OR DEAD  
BATTERY  
FULLY CHARGED  
BATTERY  
HEX  
BOLT  
FIG. 24  
02603  
POSITIVE (RED)  
CABLE  
NEGATIVE  
(BLACK) CABLE  
FIG. 26  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
INTERLOCKS AND RELAYS  
Loose or damaged wiring may cause your tractor to run  
poorly, stop running, or prevent it from starting.  
ENGINE  
TO ADJUSTTHROTTLECONTROLCABLEThe  
throttlecontrolhasbeenpresetatthefactoryandadjustment  
should not be necessary. If adjustment is necessary, see  
engine manual.  
Check wiring. See electrical wiring diagram in the  
Repair Parts section.  
TO REPLACE FUSE  
Replace with 20 amp automotive-type plug-in fuse. The  
fuse holder is located behind the dash.  
TO ADJUST CARBURETOR  
Thecarburetorhasbeenpresetatthefactoryandadjustment  
shouldnotbenecessary. However,minoradjustmentmaybe  
requiredtocompensatefordifferencesinfuel,temperature,  
altitude or load. If the carburetor does need adjustment,  
see engine manual.  
TO REMOVE HOOD AND GRILL ASSEMBLY  
(See Fig. 27)  
Raise hood.  
Stand in front of tractor. Grasp hood at sides, tilt toward  
engine and lift off of tractor.  
To replace, reverse above procedure.  
HOOD  
HEADLIGHT  
WIRE  
CONNECTOR  
01536  
FIG. 27  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
Immediately prepare your tractor for storage at the end  
of the season or if the tractor will not be used for 30 days  
or more.  
ENGINE  
FUEL SYSTEM  
IMPORTANT: ITISIMPORTANTTOPREVENTGUMDEPOSITS  
FROM FORMING IN ESSENTIAL FUEL SYSTEMPARTSSUCH  
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK  
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT  
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING  
ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH  
LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING  
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM  
OF AN ENGINE WHILE IN STORAGE.  
WARNING: Never store the tractor with  
gasoline in the tank inside a building  
where fumes may reach an open flame  
orspark. Allowtheenginetocoolbefore  
storing in any enclosure.  
TRACTOR  
Empty the fuel tank by starting the engine and let it run  
until the fuel lines and carburetor are empty.  
Never use engine or carburetor cleaner products in the  
fuel tank or permanent damage may occur.  
Removemowerfromtractorforwinterstorage. Whenmower  
istobestoredforaperiodoftime,cleanitthoroughly,remove  
all dirt, grease, leaves, etc. Store in a clean, dry area.  
Clean entire tractor (See “CLEANING” in the Mainte-  
nance section of this manual).  
Use fresh fuel next season.  
NOTE: Fuel stabilizer is an acceptable alternative in mini-  
mizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not empty  
the gas tank and carburetor if using fuel stabilizer.  
Inspect and replace belts, if necessary (See belt re-  
placement instructions in the Service and Adjustments  
section of this manual).  
Lubricate as shown in the Maintenance section of this  
manual.  
Be sure that all nuts, bolts and screws are securely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
ENGINE OIL  
Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
Drain oil (with engine warm) and replace with clean en-  
gine oil. (See “ENGINE” in the Maintenance section of  
this manual).  
BATTERY  
CYLINDER(S)  
Fully charge the battery for storage.  
Remove spark plug(s).  
After a period of time in storage, battery may require  
recharging.  
Pour one ounce of oil through spark plug hole(s) into  
cylinder(s).  
To help prevent corrosion and power leakage during  
long periods of storage, battery cables should be dis-  
connected and battery cleaned thoroughly (see “TO  
CLEAN BATTERY AND TERMINALS” in the Mainte-  
nance section of this manual).  
Turn ignition key to “STARTposition for a few seconds  
to distribute oil.  
Replace with new spark plug(s).  
After cleaning, leave cables disconnected and place  
cables where they cannot come in contact with battery  
terminals.  
If battery is removed from tractor for storage, do not  
store battery directly on concrete or damp surfaces.  
OTHER  
Do not store gasoline from one season to another.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
If possible, store your tractor indoors and cover it to  
give protection from dust and dirt.  
Cover your tractor with a suitable protective cover that  
does not retain moisture. Do not use plastic. Plastic  
cannot breathe which allows condensation to form and  
will cause your tractor to rust.  
IMPORTANT: NEVERCOVERTRACTORWHILEENGINE AND  
EXHAUST AREAS ARE STILL WARM.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Will not start  
1. Out of fuel.  
1. Fill fuel tank.  
2. Engine not “CHOKED” properly.  
3. Engine flooded.  
4. Bad spark plug.  
5. Dirty air filter.  
2. See “TO START ENGINE” in Operation section.  
3. Wait several minutes before attempting to start.  
4. Replace spark plug.  
5. Clean/replace air filter.  
6. Dirty fuel filter.  
6. Replace fuel filter.  
7. Water in fuel.  
7. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
8. Loose or damaged wiring.  
8. Check all wiring.  
9. Carburetor out of adjustment.  
9. See To Adjust Carburetor” in Service Adjustments  
section.  
10. Engine valves out of adjustment.  
10. Contact an authorized service center/department.  
Hard to start  
1. Dirty air filter.  
1. Clean/replace air filter.  
2. Bad spark plug.  
3. Weak or dead battery.  
4. Dirty fuel filter.  
2. Replace spark plug.  
3. Recharge or replace battery.  
4. Replace fuel filter.  
5. Stale or dirty fuel.  
5. Empty fuel tank and refill tank with fresh, clean  
gasoline.  
6. Loose or damaged wiring.  
6. Check all wiring.  
7. Carburetor out of adjustment.  
7. See To Adjust Carburetor” in Service Adjustments  
section.  
8. Engine valves out of adjustment.  
8. Contact an authorized service center/department.  
Engine will not turn over  
1. Clutch/brake pedal not depressed.  
2. Attachment clutch is engaged.  
3. Weak or dead battery.  
1. Depress clutch/brake pedal.  
2. Disengage attachment clutch.  
3. Recharge or replace battery.  
4. Replace fuse.  
4. Blown fuse.  
5. Corroded battery terminals.  
6. Loose or damaged wiring.  
7. Faulty ignition switch.  
8. Faulty solenoid or starter.  
9. Faulty operator presence switch(es).  
5. Clean battery terminals.  
6. Check all wiring.  
7. Check/replace ignition switch.  
8. Check/replace solenoid or starter.  
9. Contact an authorized service center/department.  
Engine clicks but will not  
start  
1. Weak or dead battery.  
1. Recharge or replace battery.  
2. Clean battery terminals.  
3. Check all wiring.  
2. Corroded battery terminals.  
3. Loose or damaged wiring.  
4. Faulty solenoid or starter.  
4. Check/replace solenoid or starter.  
Loss of power  
1. Cutting too much grass/too fast.  
2. Throttle in “CHOKE” position.  
3. Build-up of grass, leaves and trash under mower.  
4. Dirty air filter.  
1. Raise cutting height/reduce speed.  
2. Adjust throttle control.  
3. Clean underside of mower housing.  
4. Clean/replace air filter.  
5. Low oil level/dirty oil.  
5. Check oil level/change oil.  
6. Faulty spark plug.  
7. Dirty fuel filter.  
6. Clean and regap or change spark plug.  
7. Replace fuel filter.  
8. Stale or dirty fuel.  
8. Empty fuel tank and refill tank with fresh, clean  
gasoline.  
9. Water in fuel.  
9. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
10. Spark plug wire loose.  
11. Dirty engine air screen/fins.  
12. Dirty/clogged muffler.  
10. Connect and tighten spark plug wire.  
11. Clean engine air screen/fins.  
12. Clean/replace muffler.  
13. Loose or damaged wiring.  
14. Carburetor out of adjustment.  
13. Check all wiring.  
14. See To Adjust Carburetor” in Service Adjustments  
section.  
15. Engine valves out of adjustment.  
15. Contact an authorized service center/department.  
Excessive vibration  
1. Worn, bent or loose blade.  
2. Bent blade mandrel.  
1. Replace blade. Tighten blade bolt.  
2. Replace blade mandrel.  
3. Loose/damaged part(s).  
3. Tighten loose part(s). Replace damaged parts.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Engine continues to run  
when operator leaves seat  
with attachment clutch  
engaged  
1. Faulty operator-safety presence control system.  
1. Check wiring, switches and connections. If not  
corrected, contact an authorized service center/  
department.  
Poor cut - uneven  
1. Worn, bent or loose blade.  
2. Mower deck not level.  
1. Replace blade. Tighten blade bolt.  
2. Level mower deck.  
3. Buildup of grass, leaves, and trash under mower.  
4. Bent blade mandrel.  
3. Clean underside of mower housing.  
4. Replace blade mandrel.  
5. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
5. Clean around mandrels to open vent holes.  
Mower blades will not  
rotate  
1. Obstruction in clutch mechanism.  
2. Worn/damaged mower drive belt.  
3. Frozen idler pulley.  
1. Remove obstruction.  
2. Replace mower drive belt.  
3. Replace idler pulley.  
4. Frozen blade mandrel.  
4. Replace blade mandrel.  
Poor grass discharge  
1. Engine speed too slow.  
2. Travel speed too fast.  
1. Place throttle control in “FAST” position.  
2. Shift to slower speed.  
3. Wet grass.  
4. Mower deck not level.  
3. Allow grass to dry before mowing.  
4. Level mower deck.  
5. Low/uneven tire air pressure.  
6. Worn, bent or loose blade.  
7. Buildup of grass, leaves and trash under mower.  
8. Mower drive belt worn.  
5. Check tires for proper air pressure.  
6. Replace/sharpen blade. Tighten blade bolt.  
7. Clean underside of mower housing.  
8. Replace mower drive belt.  
9. Blades improperly installed.  
10. Improper blades used.  
11. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
9. Reinstall blades sharp edge down.  
10. Replace with blades listed in this manual.  
11. Clean around mandrels to open vent holes.  
Headlight(s) not working  
(if so equipped)  
1. Switch is “OFF”.  
1. Turn switch “ON”.  
2. Bulb(s) or lamp(s) burned out.  
3. Faulty light switch.  
4. Loose or damaged wiring.  
5. Blown fuse.  
2. Replace bulb(s) or lamp(s).  
3. Check/replace light switch.  
4. Check wiring and connections.  
5. Replace fuse.  
Battery will not charge  
1. Bad battery cell(s).  
1. Replace battery.  
2. Poor cable connections.  
3. Faulty regulator (if so equipped).  
4. Faulty alternator.  
2. Check/clean all connections.  
3. Replace regulator.  
4. Replace alternator.  
Engine “backfires” when  
turning engine “OFF”  
1. Engine throttle control not set between half and  
full speed (fast) position before stopping engine.  
1. Move throttle control between half and full speed  
(fast) position before stopping engine.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
SCHEMATIC  
RED  
BLACK  
BATTERY  
FUSE  
RED  
RED  
A
M
STARTER  
AMMETER  
(OPTIONAL)  
BLACK  
WHITE  
SOLENOID  
RED  
S
B
M
CLUTCH / BRAKE  
(PEDAL UP)  
G
L
WHITE  
SEAT SWITCH  
(NOT OCCUPIED)  
IGNITION  
SWITCH  
WHITE  
BLACK  
BLACK  
BLACK  
BLACK  
ATT'MENT CLUTCH  
(CLUTCH OFF)  
GROUNDING  
CONNECTOR  
BLACK  
HOUR  
METER  
(OPTIONAL)  
SPARK  
PLUG  
BLACK  
IGNITION  
UNIT  
GAP  
FUEL  
LINE  
(2 PLUGS ON  
TWIN CYL. ENGINES)  
BLUE  
CHARGING SYSTEM OUTPUT  
3 AMP DC @ 3600 RPM  
28 VOLTS AC MIN. @ 3600 RPM  
(CHARGING SYSTEM DISCONNECTED)  
RED  
FUEL SHUT-OFF SOLENOID  
(IF SO EQUIPPED)  
LIGHTING SYSTEM OUTPUT  
5 AMP AC @ 3600 RPM  
ALTERNATOR  
DIODE  
S
14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF)  
M
B
WIRING INSULATED CLIPS  
NOTE: IF WIRING INSULATED CLIPS  
WERE REMOVED FOR  
NON-REMOVABLE  
CONNECTIONS  
G
L
SERVICING OF UNIT, THEY  
SHOULD BE REPLACED TO  
PROPERLY SECURE YOUR WIRING.  
REMOVABLE  
CONNECTIONS  
IGNITION SWITCH  
POSITION  
CIRCUIT  
OFF  
ON  
M + G  
B + L  
START  
B + S + L  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
ELECTRICAL  
42  
24  
41  
43  
27  
27  
40  
26  
27  
27  
25  
16  
16  
33  
30  
48  
52  
8
29  
28  
27  
2
1
90  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
ELECTRICAL  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 16 34-65 Battery 12 Volt 25 Amp  
874 76 04-12 Bolt Hex Hd 1/4-20 Unc x 3/4  
532 17 66-89 Battery Box  
2
8
16  
24  
25  
26  
27  
28  
29  
30  
33  
40  
41  
42  
43  
48  
52  
90  
532 17 61-38 Switch Interlock Push-In  
532 00 47-99 Cable Battery 6 Ga. 44"/16W  
532 14 61-47 Cable Battery  
532 17 51-58 Fuse  
873 51 04-00 Nut Keps Hex 1/4-20 Unc  
532 12 47-73 Cable Ground 6 Ga 12"black  
532 12 13-05 Switch Plunger Nc Gray  
532 17 55-67 Switch Ign  
532 14 04-01 Key Ign  
532 17 97-30 Harness Ign  
871 11 04-08 Bolt Blk Fin Hex 1/4-20  
532 13 15-63 Cover Terminal Red  
532 17 88-61 Solenoid  
532 14 08-44 Adapter Ammeter  
532 14 19-40 Protection Wire Loop  
532 18 04-49 Cover Terminal Battery  
NOTE: All component dimensions given in U. S.  
inches 1 inch = 25.4 mm.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
CHASSIS AND ENCLOSURES  
17  
28  
30  
24  
39  
18  
24  
166  
25  
26  
25  
26  
9
5
31  
5
209  
209  
11  
15  
208  
209  
209  
8
209  
6
1
26  
16  
13  
209  
35  
145  
37  
37  
33  
10  
209  
35  
2
205  
34  
208  
38  
26  
206  
209  
38  
205  
Chassis-Elite_Basic_LT_4  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
CHASSIS AND ENCLOSURES  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 17 46-20 Chassis  
2
532 17 65-54 Drawbar  
5
532 15 52-72 Bumper, Hood/Dash  
532 18 12-71 Saddle  
532 15 51-38 Clip Retainer Slide-On  
532 19 39-34 Dash  
872 14 06-08 Bolt, Carriage 3/8-16 x 1  
532 17 49-96 Panel Dash LH  
6
8
9
10  
11  
13  
15  
16  
17  
18  
24  
25  
26  
28  
30  
31  
33  
34  
35  
37  
38  
39  
532 18 69-52 Panel Slkscr Dash RH  
874 18 05-12 Screw Mach TRHD 5/16-18uncx3/4  
873 51 05-00 Nut Keps 5/16-18 Unc  
532 18 58-47 Hood  
532 12 69-38 Bumper Hood  
874 78 06-16 Bolt Fin Hex 3/8-16 Unc x 1 Gr. 5  
819 13 13-12 Washer 13/32 x 13/16 x 12 Ga  
873 80 06-00 Nut Lock Hex w/Ins 3/8-16 Unc  
532 18 67-18 Grille  
532 18 12-72 Fender  
532 13 66-19 Bracket Fender Repl 109873x  
532 18 30-81 Footrest Pnt LH  
532 18 30-80 Footrest Pnt RH  
872 11 06-06 Bolt Rdhd Sht Sqnk 3/8-16 x 3/4  
817 49 05-08 Screw Thdrol 5/16-18 x 1/2 TYT  
532 17 57-10 Bracket Asm. Pivot Mower Rear  
532 17 47-14 Bracket Pivot  
145 532 15 65-24 Rod Pivot Chassis/Hood  
166 532 17 18-75 Screw Hwhd Hi-Lo #13-16 x 5/8  
205 817 49 06-08 Screw Thdrol 3/8-16 x 1/2  
206 532 17 01-65 Bolt Shoulder 5/16-18  
208 817 67 06-08 Screw Thdrol 3/8-16 x 1/2  
209 817 00 06-12 Screw Hex Wsh Thdrol 3/8-16  
- - - 532 00 54-79 Plug Button Blk 359 Dia Choke  
- - - 532 19 39-35 Plug Switch Light  
- - - 532 18 78-01 Plug Dome Plastic  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
DRIVE  
57  
120  
63  
21  
8
212  
59  
61  
12  
70  
66  
116  
7
10  
13  
14  
65  
64  
12  
56  
55  
112  
18  
41  
113  
202  
16  
50  
11  
51  
150  
48  
5
18  
38  
52  
30  
170  
6
32  
6
6
151  
51  
27  
49  
47  
39  
32  
30  
52  
4
263  
62  
120  
3
35  
77  
37  
36  
263  
34  
79  
26  
28  
24  
36  
19  
35  
25  
2
53  
15  
77  
74  
29  
96  
26  
78  
26  
76  
22  
27  
1
75  
drive-saddle_25  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
DRIVE  
KEY PART  
KEY PART  
NO. NO.  
DESCRIPTION  
NO. NO.  
DESCRIPTION  
1
- - - - - - - - - Transaxle, Peerless 204-506B  
(Order parts from transaxle manu-  
facturer)  
532 14 66-82 Spring Return Brake T/a Zinc  
532 12 36-66 Pulley Transaxle 18" tires  
812 00 00-28 Ring Retainer # 5100-62  
532 12 15-20 Strap Torque 30 Degrees  
817 00 05-12 Screw 5/16-18 x 3/4  
532 16 22-40 Bracket T/A Saddle Shift  
532 13 16-79 Rod Shifter  
876 02 04-16 Pin Cotter 1/8 x 1 Cad  
532 10 57-01 Washer Plate Shf 388 Sq Hole  
819 15 12-16 Washer 15/32 x 3/4 x 16 Ga.  
874 55 04-12 Bolt 1/4-28 Unf Gr 8 W/Patch  
810 04 04-00 Washer Lock Hvy Helical 1/4  
874 49 05-44 Bolt 5/16-18 Gr. 5  
873 80 05-00 Nut Lock Hx W/Ins 5/16-18 Unc  
874 78 06-16 Bolt, Fin Hex 3/8-16 Unc x 1 Gr. 5  
873 80 06-00 Nut Lock 3/8-16 Unc  
532 10 69-33 Knob  
49  
50  
51  
52  
53  
55  
56  
57  
59  
61  
62  
63  
64  
65  
66  
70  
74  
75  
76  
77  
78  
79  
96  
532 12 32-05 Retainer Belt Style Spring  
872 11 06-12 Bolt Carr Sh 3/8-16 x 1-1/2 Gr. 5  
873 68 06-00 Nut Crownlock 3/8-16 Unc  
873 68 05-00 Nut Crownlock 5/16-18 Unc  
532 10 57-10 Link Clutch  
2
3
4
532 10 57-09 Spring Return Clutch 6 75  
817 06 06-20 Screw 3/8-16 x 1-1/4  
532 13 08-01 V-Belt Ground Drive  
532 16 96-91 Keeper Belt Span Ctr  
817 12 06-14 Screw 3/8-16 x .875  
532 12 48-72 Cover Pedal Blk Round  
532 17 54-10 Engine Pulley  
5
6
7
8
10  
11  
12  
13  
14  
15  
16  
18  
19  
21  
22  
24  
25  
26  
27  
28  
29  
30  
32  
34  
35  
36  
37  
38  
39  
41  
47  
48  
532 17 39-37 Bolt Hex  
810 04 07-00 Washer Lock Hvy Hlcl Spr 7/16  
532 15 47-78 Keeper Belt Engine Foolproof  
532 13 46-83 Guide Belt Mower Drive RH  
532 13 70-57 Spacer Axle  
532 12 17-49 Washer 25/32 x 1 1/4 x 16 Ga.  
812 00 00-01 E-ring #5133-75  
532 12 35-83 Key Square 2 0 x 1845/ 1865  
532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.  
532 12 50-96 Key Woodruff  
532 13 08-04 Rod Brake Blk Zinc 26 840  
873 35 06-00 Nut Hex Jam 3/8-16 Unc  
532 10 68-88 Spring Rod Brake 2 00 Zinc  
819 13 13-16 Washer 13/32 x 13/16 x 16 Ga  
876 02 04-12 Pin Cotter 1/8 x 3/4 Cad  
532 17 57-65 Rod Brake Parking  
532 12 47-88 Retainer Spring 1"  
112 819 09 12-10 Washer 9/32 x 3/4 x 10 Ga.  
113 532 12 72-85 Strap Torque Lh  
116 872 14 06-08 Bolt Rdhd Sq Neck 3/8-16 x 1.00  
120 873 90 06-00 Nut Lock Flg 3/8-16  
150 532 17 54-56 Spacer Retainer  
151 819 13 32-10 Washer 13/32 x 2 x 10  
170 532 17 83-94 Keeper Belt T/A  
202 872 11 06-14 Bolt, 3/8 - 16 x 1-3/4 Gr. 5  
212 532 14 52-12 Nut Flange Hex Lock  
263 817 00 06-12 Screw 3/8-16 x 3/4  
275 873 90 06-00 Nut 3/8-16  
532 07 16-73 Cap Brake Parking  
532 17 49-73 Bracket Mtg Transaxle  
874 76 05-12 Bolt Hex Hd 5/16-18 Unc x 3/4  
532 17 55-78 Shaft Asm Pedal Foot  
532 12 01-83 Bearing Nylon Blk 629 Id  
819 21 16-16 Washer 21/32 x 1 x 16 Ga  
532 12 49-63 Pin Roll 3/16 x 1"  
532 17 91-14 Pulley Idler Composite  
872 11 06-22 Bolt Rdhd 3/8-16 x 2-3/4 Gr. 5  
532 17 55-56 Keeper Belt Retainer Idler  
532 12 77-83 Pulley Idler V Groove Plastic  
532 15 44-07 Bellcrank Asm  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
STEERING  
38  
12  
39  
1
41  
42  
37  
37  
36  
44  
51  
54  
88  
91  
43  
71  
68  
67  
67  
29  
46  
8
47  
67  
6
9
13  
17  
65  
46  
85  
2
8
6
7
9
85  
9
5
47  
7
9
3
32  
5
68  
82  
11  
29  
4
26  
43  
15  
40  
15  
29  
43  
6
28  
30  
8
15  
10  
steering_pl.lt_42  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
STEERING  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 18 67-80 Wheel Steering  
2
532 17 51-31 Axle Asm  
3
532 16 98-40 Spindle Asm LH  
532 16 98-39 Spindle Asm RH  
4
5
532 12 49-31 Bearing Race Thrust Harden  
532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.  
819 27 20-16 Washer 27/32 x 1-1/4 x 16 Ga.  
812 00 00-29 Ring Klip #t5304-75  
532 12 49-37 Bearing Col Strg Blk  
532 17 51-21 Link Drag  
6
7
8
9
10  
11  
12  
13  
15  
17  
26  
28  
29  
30  
32  
36  
37  
38  
39  
40  
41  
42  
43  
44  
46  
47  
51  
54  
65  
67  
68  
71  
82  
85  
88  
91  
810 04 06-00 Washer Lock Hvy Hlcl Spr 3/8  
873 94 08-00 Nut Hex Jam Toplock 1/2-20  
532 13 65-18 Spacer earing Axle Front  
532 14 52-12 Hexflange Lock  
532 18 06-41 Shaft Asm Strg  
532 12 68-47 Bushing Link Drag Blk LR  
819 13 14-16 Washer 13/32 x 7/8 x 16 Ga.  
817 00 06-12 Screw 3/8-16 x 3/4  
876 02 04-12 Pin Cotter 1/8 x 3/4 Cad  
532 13 04-65 Rod Tie Wire Form 19 75 Mech  
532 15 50-99 Bushing Strg 5/8 Id Dash  
532 15 29-27 Screw  
532 19 29-16 Cap Wheel Steer  
819 18 38-12 Washer 9/16 ID x 2-3/8 OD 12 Ga.  
873 54 06-00 Nut Crownlock 3/8-24  
532 18 67-37 Adaptor Wheel Strg  
532 16 96-33 Boot Steering  
532 12 17-49 Washer 25/32 x 1 1/4 x 16 Ga.  
532 18 06-40 Extension Steering  
532 12 12-32 Cap Spindle Fr Top Blk  
532 18 32-26 Fitting Grease  
873 54 04-00 Nut Crownlock 1/4-28  
871 13 04-20 Bolt Hex 1/4-28 Unf x 1-1/4 Gr. 8  
532 16 03-67 Spacer Brace Axle  
872 11 06-18 Bolt 3/8-16 x 2-1/4  
532 16 98-27 Brace Axle  
532 17 51-46 Steering Asm  
532 16 98-35 Bracket Susp Chassis Front  
532 13 38-35 Fastener Christmas Tree  
532 17 51-18 Bolt shoulder 7/16-20  
532 17 55-53 Clip Steering  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
ENGINE  
3
2
72  
1
81  
13  
4
78  
38  
16  
14  
32  
44  
46  
78  
33  
37  
31  
33  
40  
29  
45  
23  
OPTIONAL EQUIPMENT  
Spark Arrester  
engine-bs.1cyl_17  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
33  
37  
38  
40  
44  
45  
46  
72  
78  
81  
532 12 34-87 Clamp Hose  
1
2
3
532 17 05-51 Control Throttle/Choke Flag  
532 13 70-40 Line Fuel 20"  
817 72 04-08 Screw Hex Thd Cut 1/4-20 x 1/2  
532 18 16-54 Plug Drain Oil Easy  
532 12 40-28 Bushing Snap NYL BLK Fuel Line  
817 67 04-12 Screw Thdrol 1/4-20 x 3/4  
817 00 06-12 Screw Hex Wsh Thdrol 3/8-16  
819 09 14-16 Washer 9/32 x 7/8 x 16 Ga.  
532 18 39-06 Screw 5/16-18 x 1  
- - - - - - - -  
Engine, B&S Model No. 217707  
(Order parts from engine manufac-  
turer)  
4
532 17 97-58 Muffler  
532 16 52-91 Gasket Muffler  
13  
14  
16  
23  
29  
31  
32  
532 14 84-56 Tube Drain Oil Easy  
811 05 06-00 Washer Lock Ext Tooth 3/8  
532 16 98-37 Shield BRN/DBR Guard  
532 13 71-80 Kit Spark Arrestor (Flat Scrn)  
532 18 51-15 Tank Fuel Front  
817 06 06-20 Screw 3/8-16 x 1-1/4  
873 51 04-00 Nut Keps Hex 1/4-20 Unc  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
532 14 05-27 Cap Asm Fuel  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
SEAT  
1
8
9
8
9
14  
7
7
10  
5
6
22  
21  
2
24  
5
26  
16  
25  
15  
23  
4
13  
3
17  
12  
seat_lt.bolt_1  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
532 17 53-89 Seat  
14  
15  
16  
17  
21  
22  
23  
24  
25  
26  
872 05 04-12 Bolt Rdhd Sht Nk 1/4 - 20 x 1 -1/2  
532 13 43-00 Spacer Split .28 x .96  
2
532 14 05-51 Bracket Seat Pivot  
3
871 11 06-16 Bolt Hex 3/8 - 16 x 1  
819 13 16-10 Washer 13/32 x 1 x 10 Ga.  
532 14 50-06 Clip Push-In Hinged  
873 80 06-00 Nut Lock Hex w/Ins 3/8 - 16  
532 12 41-81 Spring Seat Cprsn 2 250 Blk Zi  
817 00 06-16 Screw 3/8-16 x 1.5  
819 13 16-14 Washer 13/32 x 1 x 14 Ga.  
532 18 24-93 Pan Pnt Seat (Blk)  
532 12 12-46 Bracket Pnt Mounting Switch  
532 12 12-48 Bushing Snap Blk Nyl  
532 12 12-50 Spring Cprsn  
4
532 12 39-76 Nut Lock 1/4 Lge Flg  
5
532 17 18-52 Bolt Shoulder 5/16-18 Unc-2A  
873 80 05-00 Nut Lock Hex w/Ins 5/16 - 18  
871 11 08-14 Bolt Hex Black  
6
7
8
819 17 19-12 Washer 17/32 x 1-3/16 x 12 Ga.  
532 12 70-18 Bolt Shoulder 5/16-18 x .62  
810 04 08-00 Washer Lock Hvy Hlcl Spr 1/2  
9
10  
12  
13  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
DECALS  
12  
2
12  
15  
7
9
13  
13  
5
11  
8
1
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
2
5
7
8
532 18 12-49 Decal, Clutch/Brake  
532 18 58-81 Decal, Steering Wheel  
532 16 88-69 Decal, Tick Mark  
532 15 70-02 Decal, Finger Danger  
532 13 68-32 Decal, V-Belt Sch.  
9
532 18 91-76 Decal, Fender  
11  
12  
13  
15  
- -  
- -  
532 18 48-53 Decal, Engine  
532 18 90-24 Decal, Hood RH/LH  
532 19 40-76 Decal, 36/11.5/4  
532 14 50-05 Decal, Caution, Battery  
532 13 83-11 Decal, Handle Lft Height Adj.  
532 19 38-89 Manual, Owner's  
KEY PART  
NO. NO.  
WHEELS & TIRES  
DESCRIPTION  
1
1
532 05 91-92 Cap, Tire valve  
2
5,8  
2
532 06 51-39 Stem, Valve  
3
532 12 41-57 Tire, Front  
532 05 99-04 Tube, Front (Service item only)  
532 18 33-37 Rim assembly, 6"front  
532 12 49-57 Fitting, Grease (Front wheel only)  
532 12 49-59 Bearing, Flange (Front wheel only)  
532 18 33-38 Rim assembly, 8" rear  
532 12 39-69 Tire, Rear  
4,10  
4
7
5
6
3,9  
7
6
11  
8
9
10  
11  
- -  
532 12 49-26 Tube, Rear (Service item only)  
532 17 50-39 Cap, Hub Axle  
532 14 43-34 Sealant, Tire (10 oz. Tube)  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
wheel_1  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
MOWER LIFT  
7
8
5
1
3
13  
2
4
6
6
11  
5
4
12  
13  
19  
20  
20  
13  
18  
17  
16  
15  
20  
31  
32  
19  
20  
15  
13  
31  
32  
lift-rh.1piece_3  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
532 17 32-88 Link Front  
15  
16  
17  
18  
19  
20  
31  
32  
1
532 15 94-61 Wire Asm Inner/Sprg w/plunger  
532 15 94-76 Shaft Asm Lift RH  
873 35 08-00 Nut Jam Hex 1/2-13 Unc  
532 17 56-89 Trunnion  
873 80 08-00 Nut Lockw/Wsh 1/2-13 Unc  
532 13 98-68 Arm Suspension Rear  
532 16 35-52 Retainer, Spring  
532 16 98-65 Bearing Pvt Lift  
873 54 06-00 Nut Crownlock 3/8-24  
2
3
532 17 89-81 Pin Groove  
4
812 00 00-02 E Ring #5133-62  
5
819 21 16-21 Washer 21/32 x 1 x 21 Ga.  
532 12 01-83 Bearing Nylon Blk 629 Id  
532 10 94-13 Grip Handle Bicycle Matte Blk  
532 12 45-26 Button Plunger Black  
532 13 98-65 Link Lift LH Fixed Length  
532 13 98-66 Link Lift RH Fixed Length  
532 12 46-70 Retainer Spring  
6
7
8
11  
12  
13  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
MOWER DECK  
45  
150  
40  
40  
89  
68  
67  
107  
4
2
3
8
158  
108  
36  
89  
185  
56  
36  
152  
45  
h_mod_7  
42_clutc  
148  
55  
54  
146  
164  
21  
21  
172  
34  
113  
171  
123  
21  
53  
30  
30  
7
170  
7
30  
21  
122  
33  
32  
1
3
169  
5
4
6
19  
21  
149  
25  
2
2
2
168  
24  
23  
31  
21  
15  
21  
2
26  
28  
27  
29  
14  
16  
13  
11  
10  
8
9
36_deck_LT_1  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER MC1136 (MC1136B), PRODUCT NO. 964 77 30-01  
MOWER DECK  
KEY  
NO.  
PART  
NO.  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
DESCRIPTION  
1
532 17 45-95 Mower Deck Assembly  
872 14 05-06 Bolt  
532 13 80-17 Bracket Assembly,Sway Bar  
532 17 56-54 Bracket Sway Bar  
532 12 46-70 Retainer Spring  
532 17 80-24 Bar Sway Deck  
532 14 06-08 Keeper Belt  
532 85 08-57 Bolt, Hex 3/8-24 x 1.25 Gr. 8  
810 03 06-00 Washer, Lock Hvy Hlcl 3/8  
532 14 02-96 Washer, Hardened  
532 13 84-96 Blade, Mower  
532 13 76-45 Shaft Assembly, Mandrel,  
532 12 87-74 Housing, Mandrel, Vented  
532 11 04-85 Bearing, Ball, Mandrel  
532 17 44-93 Stripper, Mower Deck  
532 13 28-27 Bolt, Shoulder  
873 68 05-00 Nut Crownlock 5/16-18  
532 13 66-31 Bracket, Mower Deflector  
532 10 53-04 Cap, Sleeve  
532 12 37-13 Spring, Torsion, Deflector  
532 11 04-52 Nut, Push  
53  
54  
55  
56  
67  
68  
89  
532 13 08-40 Brake Assembly  
532 17 85-15 Washer, Hardened  
532 13 38-40 Idler Arm Assembly  
532 16 57-23 Spacer, Retainer  
532 10 69-32 Knob RD 3/8-16 Plstc Thd  
532 17 49-78 Belt  
2
3
4
5
6
7
819 13 13-11 Washer 13/32 x 13/16 x 11 Ga.  
8
107 532 13 35-02 Spacer, Retainer  
9
108 532 13 35-03 Stiffener, Idler Arm  
113 817 49 05-08 Screw Thdrol 5/16-18 x 1/2  
122 532 17 45-05 Rod, Brake, LH  
10  
11  
13  
14  
15  
16  
19  
21  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
36  
40  
45  
123 532 17 45-04 Rod, Brake, RH  
146 532 16 58-91 Bolt Carriage Idler  
148 532 16 90-22 Spring Return Idler  
149 532 16 58-98 Retainer Spring Yellow Zinc  
150 819 09 12-16 Washer 9/32 x 3/4 x 16 Ga.  
152 532 17 60-79 Cable Clutch  
158 817 72 04-08 Screw Hex Thd Cut 1/4-20 x 1/2  
164 532 17 49-76 Bracket Asm Idler Support  
168 532 17 23-77 Bracket Deck Cable  
169 532 17 49-77 Bracket Asm Suspension  
170 532 17 23-59 Bracket Suspension RF  
171 532 16 52-37 Bracket Support Susp. Frt  
172 532 17 23-55 Bracket Suspension LF  
185 532 18 82-34 Head Asm Cable clutch  
532 17 61-62 Shield, Deflector  
819 11 10-16 Washer 11/32 x 5/8 x 16 Ga.  
532 12 19-80 Rod, Hinge  
532 17 39-84 Screw Thdrol  
532 12 99-63 Washer, Spacer  
- -  
532 13 07-94 Mandrel Assembly (Includes Hous-  
ing, Shaft and Shaft Hardware Only  
- Pulley Not Included)  
532 15 35-31 Pulley, Mandrel  
532 17 83-42 Nut, Toplock, Flanged  
872 11 06-14 Bolt Rdhd 3/8-16 x 1-3/4  
532 13 14-94 Pulley, Idler, Flat  
873 68 06-00 Nut Crownlock 3/8-16  
532 12 47-88 Retainer, Spring  
- -  
532 17 52-54 Replacement Mower, Complete  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE  
POLICY  
®
®
WARRANTY  
Issued January 1980  
Revised January 1991  
LIMITED WARRANTIES  
FOR  
NEW PEERLESS GEAR POWER TRAIN COMPONENTS  
A. Products Warranted  
Peerless Gear and Machine Division of Tecumseh Products Company (“Tecumseh”), subject to the limitations contained below,  
will, at its option, repair or replace, without charge for parts or labor only, any part of a new Power Train Component (which as used  
herein means and includes the transaxle, gear box, transmission, differential and right angle drives, and any part of the Power Train  
Component), EXCEPT any new Power Train Component incorporated in equipment used for commercial or rental purposes, which is  
found upon examination by any Tecumseh Authorized Service Outlet or by Tecumseh’s factory in Grafton, Wisconsin, to be DEFECTIVE  
IN MATERIAL AND/OR WORKMANSHIP if received by Tecumseh or a Tecumseh Authorized Service Outlet for such examination within  
TWO YEARS from the date of sale to the original consumer purchaser of Peerless Series 820, 900, 910, 915, 920, 930 transaxles and  
Series 1100 angle drive and ONEYEAR for all other Peerless products. New PowerTrain Components incorporated in equipment used for  
commercial purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted  
for NINETY (90) DAYS ONLY, and must be received by Tecumseh or by a Tecumseh Authorized Service Outlet for such examination  
within 90 days from the date of sale to the original purchaser. New Power Train Components Incorporated in equipment used for rental  
purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted for THIRTY  
(30) DAYS ONLY, and must be received by Tecumseh or a Tecumseh Authorized Service Outlet within 30 days from the date of sale to  
the original purchaser.  
B. Products And Items Not Warranted  
1.  
2.  
Alterations or Modifications of Power Train Components.  
Accidents, Normal Maintenance, Failure to follow the Original Equipment Manufacturer’s Manual.  
This warranty covers only parts of new Power Train Components which are found upon examination to be defective in material  
or workmanship as delivered to the original purchaser. This warranty does not cover defects caused by depreciation or damage caused  
by normal wear, accidents, improper maintenance, improper use or abuse of the product, failure to follow the instructions contained in  
an Instruction Manual for the operation of the Power Train Component and parts. The cost of normal maintenance and replacement of  
service items which are not defective shall be paid for by the original purchaser.  
C. Securing Warranty Service  
Warranty service can be arranged for by contacting either a Tecumseh Authorized Service Outlet (any Tecumseh Registered  
Service Dealer, Tecumseh Authorized Service Distributor, or Tecumseh Central Warehouse Distributor) or by contacting Tecumseh, c/o  
Service Manager, Engine and Transmission Group Service Division, 900 North Street, Grafton, Wisconsin 53024. Warranty service  
can only be performed by a Tecumseh Authorized Service Outlet or by Tecumseh at its factory in Grafton, Wisconsin. At the time of  
requesting warranty service, evidence must be presented of the date of sale to the original purchaser. The purchaser shall pay any  
charges for making service calls and/or for transporting the product to and from the place where the inspection and/or warranty work  
is performed. The purchaser shall be responsible for any damage or loss incurred in connection with the transportation of Power Train  
Components and/or part(s) of the Power Train Components submitted for inspection and/or warranty work.  
D. Limitation of Damages and Implied Warranties  
The foregoing EXPRESSED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. Neither Tecumseh nor any  
of its affiliates makes any warranties, representations or promises, written or oral, as to the quality of the Power Train Component or any  
of its parts, other than as set forth herein.  
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, TO THE EXTENT THAT  
EITHER MAY APPLY TO ANY PART(S) OF POWER TRAIN COMPONENTS, SHALL BE LIMITED IN DURATION TO THE PERIODS  
OF THE EXPRESSED WARRANTIES DEFINED IN PARAGRAPH A HEREOF. IN NO EVENT WILL TECUMSEH BE LIABLE FOR ANY  
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES AND/OR EXPENSES. Some states do not allow limitations on how long  
an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation(s) or exclusion(s)  
may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights which vary from state to  
state.  
E. No Dealer Warranty  
Tecumseh neither assumes nor authorizes any other person, natural or corporate, to assume forTecumseh any other obligations  
or liabilities in connection with or with respect to any part(s) of a Power Train Component. The seller or dealer of part(s) of a Power Train  
Component has no authority, whatsoever, to make any representations or promises on behalf of Tecumseh or to modify the terms or  
limitations of Tecumseh’s warranty in any way.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION  
ONLY RIDE UP AND DOWN HILL,  
NOT ACROSS HILL  
15 DEGREES MAX.  
WARNING: To avoid serious injury, operate your tractor up and  
down the face of slopes, never across the face. Do not mow  
slopes greater than 15 degrees. Make turns gradually to prevent  
tipping or loss of control. Exercise extreme caution when  
changing direction on slopes.  
1. Fold this page along dotted line indicated above.  
2. Hold page before you so that its left edge is vertically parallel to a tree  
trunk or other upright structure.  
3. Sight across the fold in the direction of hill slope you want to measure.  
4. Compare the angle of the fold with the slope of the hill.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Krown Manufacturing Stereo Amplifier K RA02 User Manual
LevelOne Router WBR 6001 User Manual
Life Fitness Bicycle LCUT8 User Manual
Lincoln Electric Welding System L12810 1 User Manual
LOREX Technology Security Camera L15D424321B User Manual
Magnasonic Flat Panel Television 32612MHD User Manual
Makita Drill 6015DWE User Manual
Makita Impact Driver BTD130F User Manual
Makita Saw LS1212 User Manual
MB QUART Speaker RTC25 User Manual