GENERAL SAFETY RULES
GB
Meaning of symbols marked on the product
Read the user manual before using the machine.
Warning! Danger.
Primer bulb.
Wear safety goggles to protect your eyes; Wear
ear protector to protect against noise.
X 10
The engine continues to rotate after the unit is
switched off.
USER MANUAL
Petrol Back Pack Blower
Keep bystanders away.
Acoustic power level LWA accordance with directive
2000/14/EC
Never work while people,especilly children or pets
are nearby.
MANUEL DE L’UTILISATEUR
Souffleur à essence en sac à dos
HANDLEIDING
Warning! Hot surface.
Rugblazer op benzine
SAFETY OPERATION MAINTENANCE
SECURITE FONCTIONNEMENT ENTRETIEN
VEILIGHEID BEDIENING ONDERHOUD
•
WHAT NOT TO DO
•
WHAT TO DO
READ YOUR USER MANUAL AND ALL
SUPPLEMENTS (IF ANY ENCLOSED) THOROUGHLY
BEFORE OPERATING YOUR UNIT.
WARNING: DO NOT USE ANY OTHER
FUEL than that recommended in your
manual. Always follow instructions in the
Fuel and Lubrication section of this manual.
Never use petrol unless it is properly
mixed with 2-cycle engine lubricant.
Permanent damage to engine will result,
voiding manufacturer’s warranty.
1. WEAR CLOSE FITTING, TOUGH WORK
CLOTHING that will provide protection, such as long
slacks or trousers, safety work shoes, heavy duty
work gloves, hard hat, a safety face shield, or safety
glasses for eye protection and a good grade of ear
plugs or other sound barriers for hearing protection.
2. REFUEL IN A SAFE PLACE. Open fuel cap slowly
to release any pressure which may have formed in
fuel tank. Always wipe unit of fuel or oil spills before
starting. To prevent a fire hazard, move at least 10
feet (3 meters) from fueling area before starting.
3. TURN UNIT OFF before setting it down, and also
before installing or removing attachments.
4. KEEP ALL SCREWS AND FASTENERS TIGHT and
the unit in good operating condition. Never operate
this equipment if it is improperly adjusted or not
completely and securely assembled.
1. DO NOT SMOKE while refueling or operating
equipment.
2. DO NOT OPERATE UNIT WITHOUT A MUFFLER
and properly installed muffler shield.
3. DO NOT TOUCH or let your hands or body come in
contact with a hot muffler or spark plug wire.
4. DUE TO THE DANGER of exhaust fumes, never
operate blower in a confined or poorly ventilated
area.
5. NEVER POINT BLOWER in the direction of people,
animals, buildings, automobiles, or windows, etc.
6. DO NOT operate unit without inlet cover installed to
prevent contact with impeller.
5. KEEP HANDLES DRY, clean and free of fuel
mixture.
7. DO NOT set a hot engine down where flammable
material is present.
8. DO NOT OPERATE UNIT FOR PROLONGED
PERIODS. Rest periodically.
6. STORE EQUIPMENT AWAY FROM POSSIBLE
IGNITION SOURCES, such as gas-powered water
heaters, clothes dryers, or oil-fired furnaces,
portable heaters, etc.
7. ALWAYS KEEP the engine free of debris build-up.
8. OPERATION OF EQUIPMENT should always be
restricted to mature and properly instructed
individuals.
9. ALL PERSONS WITH RESPIRATORY PROBLEMS
and persons operating blower in very dusty
environments, should wear a dust particle mask at
all times. Paper dust masks are available at most
paint and hardware stores.
10. Operate the machine only at reasonable hours- not
early in the morning or late at night when people
might be disturbed. Comply with times listed in local
ordinances.
11. Operate the machine at the lowest possible engine
speed to do the job.
WARNING: DO NOT ADD, REMOVE OR
ALTER ANY COMPONENTS OF THIS
PRODUCT. Doing so could cause personal
injury and/or damage the unit voiding the
manufacturer’s warranty.
WARNING • PLEASE READ
For your own safety please read this manual before attempting to operate your new unit. Failure to
follow instructions can result in serious personal injury. Spend a few moments to familiarize yourself
with your blower before each use.
9. DO NOT OPERATE UNIT WHILE UNDER THE
INFLUENCE OF ALCOHOL OR DRUGS.
10. DO NOT operate your unit near or around
flammable liquids or gases whether in or out of
doors. An explosion and/or fire may result.
11. DO NOT WEAR loose clothing, scarfs, neck chains,
unconfined long hair, and the like. Doing so could
cause injury associated with objects being drawn
into the rotating parts.
ATTENTION – LISEZ SVP
Pour votre propre sécurité, veuillez lire attentivement ce manuel avant de tenter de faire fonctionner
votre nouvel appareil. Le non-respect des instructions peut entraîner des accidents graves. Prenez
quelques instants pour vous familiariser avec le souffleur avant chaque utilisation.
WAARSCHUWING – AANDACHTIG LEZEN
12. DO NOT refuel a running engine or an engine that is
hot.
13. Never allow children to operate the appliance.
12. Use rakes and brooms to loosen debris before
blowing.
13. In dusty conditions, slightly dampen surfaces.
14. Use the full blower nozzle extension so the air
stream can work close to the ground.
In het belang van uw veiligheid is het noodzakelijk dat u de handleiding leest voordat u met uw nieuw
apparaat aan de slag gaat. Het niet opvolgen van de instructies kan ernstige letsels veroorzaken.
Neem voldoende tijd om uzelf vertrouwd te maken met de bladblazer voordat u hem daadwerkelijk
gebruikt.
15. Watch out for children, pets, open windows etc. and
blow debris safety away.
MODEL NO./Modèle n°/MODELLNR. MAC BP290
9096-320643
2
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
GB
•
•
FUEL MIXING TABLE
•
STOPPING THE ENGINE
•
OPERATION INSTRUCTIONS
1. Follow the instructions “STARTING A COLD
ENGINE”.
2. Once unit is running, place unit on your back by
slipping arms through the shoulder straps as if your
were putting on a jacket (Fig. 17).
3. When preparing to clear an area of debris, always
position yourself so that you can control the direction
debris will be blown. (Fig. 18)
4. The control handle and the flexibility of the blower
tube assembly will allow you to clear the most
hard-to-reach areas .
Emergency Stopping Procedure. When it is necessary
to stop blower engine immediately, press and hold the
ON/STOP switch (A) until the engine stops completely
(Figure 16).
Normal Stopping Method. For normal stopping, release
trigger and allow engine to return to idle speed. Then
press and hold the ON/STOP switch (A) until the engine
stops completely. (Figure 16)
PETROL
40:1
95ml (cm3)
125ml (cm3)
125ml (cm3)
1 U.S. Gal.
5 Liters
3.2 oz.
4.3 oz.
4.3 oz.
1 lmp. Gal.
Mixing Ratio 40 Parts Petrol to 1 Part Lubricant
Fig. 13
Fig. 14
RECOMMENDED FUELS
•
BLOWER OPERATIONS
Some conventional petrols are being blended with oxy-
genates such as alcohol or an ether compound to meet
clean air standards. Your engine is designed to
operate satisfactorily on any petrol intended for auto-
motive use including oxygenated petrol.
WARNING: Because of flying debris, always,
approved shielded safety glasses or face
shield when operating blower.
5. Move choke lever to HALF CHOKE position. (Fig.13)
6. Pull starter rope slowly until engine starts.
7. Allow engine to run 10 seconds; then, move the
choke lever to RUN position.(Fig.14)
5. The hand grip, throttle trigger, throttle adjuster and
ignition on/stop switch are all mounted on a swivel
handle that offers a wide range of operating positions
and comfort (Fig. 19).
8. Press trigger to run.
WARNING: Before using your blower, review
Safety Precautions in your User Manual, and
all regulations for operation of the unit. These
precautions and regulations are for your pro-
tection.
NOTE: Always pull starter rope straight out. Pulling starter
at an angle will cause rope to rub against the eyelet. This
friction will cause the rope to fray and wear more quickly.
Always hold starter handle when rope retracts. Never let a
rope snap back from extended position. This could cause
rope to snag or fray and also damage the starter
assembly.
STARTING/STOPPING INSTRUCTIONS
•
STARTING A COLD ENGINE
NOTE: This product is designed to be started at idle.
WARNING: DO NOT operate the blower with
other people or animals in the immediate
vicinity. Allow a minimum of 30 feet (10
meters) between operator and other people
or animals.
1. Pump primer bulb10 X by pressing up on the bulb
(D). (Fig. 10)
2. Your unit is designed with a 3-position choke: FULL
CHOKE , HALF CHOKE and RUN.
•
STARTING A WARM ENGINE
Move choke lever to FULL CHOKE position. (Fig. 9)
Fig. 17
Fig. 18
1. Move choke lever to HALF CHOKE position. (Fig.13)
2. Pull starter rope slowly until engine starts.
3. Allow engine to run 10 seconds; then, move the
choke lever to RUN position.(Fig.14)
1. Use the blower for trees, shrubs, flower beds, and
hard-to-clean areas.
2. Use the unit around buildings and for other normal
cleaning procedures.
3. Use the blower around walls, overhangs, fences, and
screens.
4. We recommend that a face mask be worn when
operating blower in dusty areas.
5. Stand away from the debris, at a distance that will
easily allow you to control the direction of blown
debris. Never blow debris in direction of bystanders.
6. To control velocity of airstream, blower can be
operated at any speed between idle and full throttle.
Experience with the unit will help you determine the
amount of airflow necessary for each application.
7. Operate power equipment only at reasonable
hours-not early in the morning or late at night when
people might be disturbed. Comply with times listed
in local ordinances.
8. To reduce sound levels, limit the number of pieces of
equipment used at any one time.
9. Operate power blowers at the lowest possible throttle
speed to do the job.
10. Check your equipment before operation, especially
the muffler, air intakes and air filters.
11. Use rakes and brooms to loosen debris before
blowing. In dusty conditions, slightly dampen
surfaces when water is available.
12. Conserve water by using power blowers instead of
hoses for many lawn and garden applications,
including areas such as gutters, screens, patios,
grills, porches and gardens.
NOTE: Easy Start power assist starting significantly
reduces the pulling effort. Pull the starter cord slowly until
fully extended, the power assist will turn over the engine
with little resistence from the engine.
B
NOTE: If engine has not started, pull starter rope 5 more
pulls. If engine still does not run, it is probably flooded.
Move the choke lever to the RUN position. Grip starter
handle and pull starter rope slowly rope to clear the
engine of excess fuel. If engine fails to srart after repeated
attempts, refer to troubleshooting section.
3. Squeeze throttle trigger and turn throttle adjuster
clockwise until it stops.
A
Throttle adjuster position：
(1) Idling
(2) Full Throttle (Fig.11)
Fig. 19
Fig. 20
MAINTENANCE INSTRUCTIONS
AIR FILTER
•
IMPORTANT IDLING INFORMATION
4. With the unit on the ground,hold the top assist handle
and step on the bottom of the frame with your foot.
(Fig.12)
In some cases due to operating conditions (altitude,
temperature etc.) your blower may need a slight
adjustment to the idle speed.
If unit does not idle after restarting 2 times after warm up,
follow these steps to adjust idle.
•
CAUTION: NEVER operate blower without
the air filter or dust and dirt will be sucked into
the engine and damage it. The air filter must
be kept clean. If it becomes damaged, install
a new filter.
Pull starter rope slowly until engine sounds as if it is
trying to start, but do not pull rope more than 6 times.
1. Locate the idle adjustment screw (G) on the
carburetor (Fig. 15).
2. Using a Phillips or slotted screwdriver - turn screw 1/4
to 1/2 turn clockwise (to the right). Unit should then
idle properly.
To Clean Air Filter:
1.
Loosen knob (A)
holding air filter cover
in place, remove
C
D
cover (B) and lift filter
(C) from air box (Fig.
20 & Fig. 21).
G
A
Fig. 9
Fig. 10
2. Wash filter in soap and
water. DO NOT USE
PETROL!
Throttle
Adjuster
START
position
Fig. 21
3. Air dry filter.
13. Watch out for children, pets, open windows or freshly
washed cars, and blow debris safely away.
14. Use intermediate tube plus nozzle of your choice so
the airstream can work close to the ground.
15. After using blowers and other equipment, CLEAN
UP! Dispose of debris in trash receptacles.
4. Reinstall air filter and air filter cover.
NOTE: Replace filter if frayed, torn, damaged or unable to
be cleaned.
Fig. 15
Fig. 16
Throttle
Trigger
(1)
(2)
Fig. 11
Fig. 12
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
GB
•
FUEL CAP / FUEL FILTER
•
SPARK ARRESTOR SCREEN / COLLAR
ASSEMBLY
TROUBLE SHOOTING THE ENGINE
CAUTION: Remove fuel from unit and store
in approved container before starting this
procedure. Open fuel cap slowly to release
any pressure which may have formed in fuel
tank.
1. To replace spark arrestor screen/collar assembly (A)
(Fig. 26), use a needle nose pliers and pinch an
edge of the collar. Pull out the whole spark arrestor
screen assembly.
2. Use the needle nose pliers to push in a new spark
arrestor screen assembly by opening the pliers
slightly to press the inner surface of the assembly
securely into place
PROBLEM
PROBABLE CAUSE
CORRECTIVE ACTION
Follow instructions in the User Manual.
Unit won’t start or starts but will not run.
Incorrect starting procedures.
Incorrect carburetor mixture adjustment
setting.
Have carburetor adjusted by an Authorized
Service Center.
NOTE: Keep vent (A) on fuel cap clean of debris (Fig. 22).
Fuel Filter:
1. Completely remove fuel cap from fuel tank (B) to be
able to remove fuel filter (C) from tank. Use a piece of
wire (C) with a hook formed at the end to pull filter out
of tank. (Fig. 23)
2. Pull off fuel filter (D) with a twisting motion.(Fig. 24).
3. Replace fuel filter.(Fig. 24).
NOTE: Never operate the blower without the fuel filter.
Internal engine damage could result!
Fouled spark plug.
Clean/gap or replace plug.
Empty fuel tank.
Fill fuel tank with properly mixed fuel.
Press primer bulb fully and slowly 10 times.
Replace the fuel filter.
Primer bulb was not pressed enough.
Fuel filter is plugged.
•
STORAGE
Unit starts, but engine has low power.
WARNING: Failure to follow these steps may
Incorrect lever position.
Dirty spark arrestor screen.
Dirty air filter.
Move to RUN position.
cause varnish to form in the carburetor and
difficult starting or permanent damage follow-
ing storage.
Replace spark arrestor screen.
Remove, clean and reinstall filter.
Have carburetor adjusted by an Authorized
Service Center.
Incorrect carburetor mixture adjustment
setting service dealer.
Incorrect carburetor mixture adjustment
setting.
1. Perform all the general maintenance recommended
in the Maintenance Section of your User Manual.
2. Clean outside surface of unit.
Engine hesitates.
Have carburetor adjusted by an Authorized
Service Center.
A
3. Drain fuel from the fuel tank.
4. After fuel is drained, start engine.
5. Run engine at idle until unit stops. This will purge
the carburetor of fuel.
6. Allow engine to cool (approx. 5 minutes).
7. Using a spark plug wrench, remove the spark plug.
8. Pour 1 teaspoon of clean 2 stroke engine oil into the
combustion chamber. Pull starter rope slowly
several times to coat internal components. Replace
spark plug.
Air filter is plugged.
Replace or clean the air filter.
Drain fuel tank/add fresh fuel mixture.
Have carburetor adjusted by an Authorized
Service Center.
C
B
Old or improperly mixed fuel.
Incorrect carburetor mixture adjustment
setting.
No power under load.
Old or improperly mixed fuel.
Air filter is plugged.
Drain fuel tank (see storage)/add fresh fuel
mixture.
Fig. 22
Fig. 23
•
CARBURETOR
ADJUSTMENT
Fouled spark plug.
Replace or clean the air filter.
Replace or clean the spark plug.
Clean/gap or replace plug.
9. Store unit in a cool, dry place away from any source
of ignition such as an oil burner, water heater, etc.
C
The carburetor was pre-set
at the factory for optimum
performance. If further
adjustments are necessary
take your blower to a
Runs erratically.
Incorrectly gapped spark plug.
Plugged spark arrestor.
Dirty air filter.
•
REMOVING A UNIT FROM STORAGE
Clean or replace spark arrestor.
Clean or replace air filter.
1. Remove spark plug.
2. Pull starter rope briskly to clear excess oil from
combustion chamber.
3. Clean spark plug or install a new spark plug with
proper gap.(Fig. 25)
Smokes excessively.
Incorrect carburetor mixture adjustment
setting.
Have carburetor adjusted by an Authorized
Service Center.
qualified service dealer.
Fig. 24
Incorrect fuel mixture.
Use properly mixed fuel(40:1 mixture).
•
SPARK PLUG
4. Prepare unit for operation.
5. Fill fuel tank with proper fuel / oil mixture. See Fuel
and Lubrication Section.
1. To remove spark plug (B) (Fig. 26) for cleaning or
replacement: make sure engine is off, spark plug is
cool, then grasp spark plug boot firmly and remove
from spark plug. Remove spark plug with correct
spark plug tool. Inspect, clean or replace as needed.
2. Spark plug gap = .025 in. (.635mm) (Fig. 25).
3. Torque to 105 to 130 inch pounds (12 to 15 N•m).
Connect spark plug boot.
4. If need replace spark plug with Champion RZ7C or
equivalent.
B
.025” (.635mm)
Spark
Plug
A
Fig. 25
Fig. 26
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
EU Declaration of Conformity
according to the regulations 98/37/EC, 2004/108/EC,
2000/14/EC+2005/88/EC, 2004/26/EC
For the following equipment / product : Petrol Back Pack Blower
Type Designation
Trademark
Importer's Name
:
:
:
MAC BP290
McCULLOCH
Husqvarna AB
Importer's Address
:
SE-561 82 Huskvarna, Sweden
We herewith confirm to comply with the requirements set out in the Council
Directive 98/37/EC, 2004/108/EC, 2000/14/EC+2005/88/EC, 2004/26/EC.
For the evaluation of the compliance with these Directives, the following
standards were applied:
EN ISO 14982:1998
Sound pressure level : 94 dB(A)
Sound power level : 102 dB(A)
Guarantee sound power level : 104 dB(A)
Person responsible for making this declaration
Name, surname
Position/Title
: Ronnie Goldman
: Director of Engineering
Handheld Consumer Products
Shanghai P.R.C.
2008/12/11
9
Download from Www.Somanuals.com. All Manuals Search And Download.
|