Maytag Appliance Trim Kit DB10 User Manual

®
DB10  
Bottom Freezer  
Refrigerator  
Trim Kit  
Installation  
Instructions  
Keep these instructions for future  
reference.Iftherefrigeratorchanges  
ownership, be sure this manual accom-  
paniesrefrigerator.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Procedure  
13. Install freezer door by positioning door on bottom  
hinge pin.  
14. Install center hinge pin and door closure.  
15. Install freezer door decorator panel by sliding panel in  
from handle side of freezer door.  
Caution  
To avoid property damage, protect soft vinyl or  
other flooring with cardboard, rugs, or other  
protective material.  
16. Align handle side freezer door trim. After verifying  
placement, peel off paper backing and press trim in  
place. Handle side freezer trim will be cupped on both  
ends.  
17. Open door 180° then close door to confirm panel and  
trim fit properly.  
1. Remove screw caps on refrigerator and freezer  
handles by placing screwdriver, blade end covered  
with masking tape, in notched area then lifting up.  
2. Remove door handles by removing screws with a  
Phillips screwdriver.  
3. Remove plugs from top and sides of doors by placing  
screwdriver, blade end covered with masking tape,  
underneath plugs and lifting up.  
Refrigerator Door  
Important  
Permanent, double-sided tape is used to attach trim  
pieces. Before removing paper backing, check  
placement of trim pieces on door. Trim pieces may be  
damaged if adjustment or removal is attempted after  
installation.  
19. Install new bottom door trim by installing screws in  
inside holes. Install door stop in previous location by  
installing screws. Install and tighten remaining  
screws. Bottom refrigerator door trim will have 6 round  
holes. DB10S kit comes with a silver door stop for the  
refrigerator door.  
5. Remove top hinge cover by lifting back and sliding  
forward. Remove top hinge by removing screws with a  
5/16" hex nut driver.  
6. Remove refrigerator door by lifting while opening. This  
will release refrigerator door from center hinge pin.  
Place door on a soft, flat surface.  
7. Lift door closure off center hinge pin. Remove center  
hinge pin with a 9/32" hex nut driver.  
8. Remove freezer door by lifting while opening. This will  
release freezer door from bottom hinge pin. Place  
door on a soft, flat surface.  
20. Align top and hinge side door trim on door. After  
verifying placement, peel off paper backing and press  
trim in place. Top refrigerator door trim will have no  
holes in it. Hinge side refrigerator door trim will be  
cupped on both ends.  
9. Confirm doors are clean and dry.  
10. Remove doors stop from bottom of doors by removing  
screws with a Phillips screwdriver. Remove remaining  
screws from bottom of doors.  
Important  
21. Install top hinge bracket on top of refrigerator by  
installing rear screws loosely with a 5/16" hex nut  
driver. Position refrigerator door on door closure.  
Install remaining screw and tighten all screws. Verify  
handle side of door is approximately 1/8" higher than  
the hinge side. Door lowers when loaded with food  
and when panel is installed. Replace top hinge cover  
by snapping on.  
Permanent, double-sided tape is used to attach trim  
pieces. Before removing paper backing, check  
placement of trim pieces on door. Trim pieces may be  
damaged if adjustment or removal is attempted after  
installation.  
Freezer Door  
11. Install bottom trim by installing screws in inside  
holes. Reinstall door stop and remaining screws.  
Bottom freezer door trim will have 6 sets of round  
holes.  
22. Install refrigerator door decorator panel by sliding  
panel in from handle side of refrigerator door.  
12. Align top and hinge side trim on door. After checking  
placement, peel off paper backing and press trim in  
place. Top freezer door trim will have 4 holes for  
handle. Hinge side door trim will be cupped on both  
ends.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
23. Align handle side door trim. After verifying placement,  
peel off paper backing and press trim in place.  
Handle side trim will have 4 holes for screws to mount  
the handle, and cupped on both ends.  
Refrigerator  
door  
Top trim  
Handle  
Side trim  
29. Open door 180° then close door to confirm panel and  
trim fit properly.  
30. Replace handles by positioning handles on door.  
Insert and tighten screws with a Phillips screwdriver.  
31. Replace screw caps on refrigerator and freezer  
handles by snapping on.  
1996 Amana Refrigeration, Inc.  
Amana, Iowa 52204  
Part No.12134202  
Printed in U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

KWC Outdoor Shower Z534673700 User Manual
La Crosse Technology Portable Radio WS 550 US User Manual
La Pavoni Coffee Grinder PA JVD User Manual
Lathem Clock PC50 60 User Manual
LG Electronics Microwave Oven LMV2015 User Manual
Lochinvar Boiler 10 13 15 User Manual
Lux Products Thermostat PSP711TS User Manual
Manitowoc Ice Ice Maker 7626803 User Manual
Melissa Vacuum Cleaner 640 062 User Manual
Melitta Espresso Maker MEPE123B User Manual