Maxon Telecom Two Way Radio S5 PMR446 User Manual

S5 PMR446  
User Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
User Manual  
S5  
Operating Instructions  
About Your S5 Radio  
Maxon's S5 radio features up to 8 channels. Operation and functions of these radios are outlined  
in this manual.  
We urge you to thoroughly read this manual before operating the radio  
The application of some of the functions described in this manual is determined by the sytem you  
use. Your Maxon Dealer will program your radio so that you have the greatest number of  
functions possible relative to your needs.  
S5 Specification  
MODEL  
EQUIPMENT TYPE  
PERFORMANCE SPECIFICATIONS  
BAND  
S5  
PMR446  
EN 300.296  
446.00625~446.09375MHz  
12.5KHz  
CHANNEL SPACING  
RF OUTPUT POWER  
MODULATION TYPE  
AUDIO POWER  
500Mw (ERP)  
F3E  
500Mw (EXT WITH 8 OHM)  
1 W (INT WITH 4 OHM)  
45.1MHz  
INTERMEDIATE FREQUENCIES  
455KHz  
CHANNELS  
8 Channels  
FREQUENCY SOURCE  
POWER SUPPLY  
SYNTHESIZER  
Li-ion(1500mA)  
7.5VDC Nominal  
+/- 10% VDC Extreme  
Page 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
User Manual  
S5  
Safety Information  
WARNING  
¾ DO NOT hold the radio in such a manner that the antenna is next to, or touching, exposed  
parts of the body while transmitting.  
¾ DO NOT allows children to operate transmitter-equipped radio equipment.  
CAUTION  
¾ DO NOT operate the radio near unshielded electrical blasting caps or in an explosive  
atmosphere unless it is a type especially designed and qualified for such use.  
¾ DO NOT press and hold the transmit switch (P-T-T) when not actually wishing to transmit.  
¾ NEVER use the radio in an aircraft.  
¾ NEVER use the radio near to sensitive medical equipment or in areas where instructed not to  
do so, e.g. Petrol filling stations.  
¾ When used in a vehicle, do not mount the radio unit on or near the Airbag or Airbag  
activation device.  
¾ The use of an accessory not recommended or supplied by Maxon may cause damage to  
equipment or injury to personnel, and will invalidate warranty.  
¾ When using any of the charging accessories, the mains socket-outlet must be installed near  
the equipment.  
¾ The outlet must not be obstructed and must be easily accessible at all times.  
¾ Never attempt to disassemble, modify or repair the unit unless the work is carried out by a  
Maxon approved Dealer.  
Incorrect assembly, modification or repair may cause irreparable damage to your unit and will  
invalidate warranty.  
For service or repair always return your radio to an authorized Maxon Dealer.  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
User Manual  
S5  
Unpacking Information  
Remove and carefully inspect the contents of your package(s) for the following items:  
1. Radio  
2. Battery Pack  
3. Battery Charger  
4. Spring Belt Clip  
5. Jack Cover  
6. Battery Charger Power Supply  
7. User Manual  
* If any items are missing, please contact your Dealer or Maxon  
Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
User Manual  
S5  
S5 Features  
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
500mW output power  
12.5KHz channel spacing  
Full scanning  
Password protect  
Emergency call  
CTCSS/DCS/tone signalling  
Li-ion Battery  
2-Tone Decode  
Busy Channel lockout  
Time-out timer  
Priority Channel Edit  
Description of Radio Components  
(Please see drawing on page 6)  
1. Fixed Antenna  
2. Channel Selector Switch  
3. On/Off – Volume Control  
4. Emergency Button  
5. Push-To-Talk (PTT)  
6. Monitor Button  
7. Option Button  
8. Battery  
9. RX/TX Indicator  
10. Speaker  
11. Microphone  
12. Accessory Connector (EXT Jack)  
13. Battery Latch  
14. Belt Clip  
15. Battery Charge Contacts  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
User Manual  
S5  
Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
User Manual  
S5  
Installing and Removing the Battery Pack  
To Install:  
Position the guides of the battery in line with the radio battery guide rails and slide the battery  
into position until a click is heard.  
To Remove:  
Holding the radio in one hand, push and hold the battery latch button located in the upper central  
part of the battery pack, held as if looking at the back of the unit. Hold the radio firmly and slide  
the battery in a downward direction whilst pushing the battery latch button.  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
User Manual  
S5  
Attaching and Removing the Belt Clip  
To Install:  
Install belt clip onto the belt clip holder located on the upper part of the battery, held whilst  
looking at the back of the unit. Locate the slot on the battery and push belt clip downward until a  
click is heard.  
To Remove:  
Push and hold the release button located at the top of the belt clip and slide the clip off the belt  
clip holder.  
Attaching and Removing the Jack Cover  
To attach accessory socket cover screw as per below drawing, in the case of using an optional  
audio accessory unscrew cover using a screwdriver, fit accessory and fully tighten locating pin.  
Page 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
User Manual  
S5  
Battery Charging and Care  
To ensure peak performance from your radio, the battery pack must be fully charged. Proper care  
and charging will allow maximum performance and life of your battery pack.  
CH-SL1000-02 Desktop Charger provides 2 hours charging to one radio and one battery.  
Before using your S5 for the first time a full two hour charge will be required for the best  
performance.  
To ensure maximum performance from your radio and battery pack, periodically completely  
discharge and recharge the battery pack.  
Page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
User Manual  
S5  
Status Indicators and Audible Alert Tones  
Your S5 has a sophisticated microprocessor control which provides a series of audible alert tones.  
Upon initial power up, a quick melody indicates that the self-test of the microprocessor functions  
has been completed satisfactorily. A series of tones may be sounded with any of the following  
conditions:  
ƒ
ƒ
Attempt to transmit on a channel set for receive only  
Attempt to transmit on a channel that is already in use when busy channel lockout has been  
programmed on the radio*  
ƒ
ƒ
ƒ
Transmitting time has exceeded time-out timer programmed length*  
Low battery condition  
Selecting a channel with no programmed frequency  
* Indicates a function that is initially programmed into the radio by your Maxon Dealer.  
NOTE: All audible tones can be programmed for silent operation.  
Status  
Normal  
Description  
Power On - Ready  
Call Received  
LED color  
N/A  
Orange  
Green  
Audible Tone  
Melody  
N/A  
N/A  
Correct Call  
Busy Channel  
Orange  
Red  
N/A  
N/A  
Transmit  
Transmit not allowed  
Normal Scan Mode  
Low Battery  
Busy Channel Lockout  
TX Inhibit  
Red Flashing  
Green Flashing  
Red Flashing  
Orange  
N/A  
Two beeps  
N/A  
Scanning  
Warning  
2 beeps repeated  
2 beeps repeated  
Two beeps  
Single beep/3 beeps  
repeated  
Time-out-timer  
N/A  
Error  
Unlock  
N/A  
Two beeps  
Page 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
User Manual  
S5  
Operation Mode  
This section provides general descriptions of the operating modes of the S5 Radio.  
Power off Mode  
The S5 shall enter Off mode when the On/Off Volume knob is rotated to the most counter-  
clockwise position, beyond the detent. Upon entering off mode, the radio shall store its current  
channel (if Power On Channel function is enabled via PC Programmer).  
Power on Mode  
The S5 shall enter Power-On mode when the On/Off Volume knob is rotated clockwise beyond  
the detent. Upon entry of the Power-On mode, the radio shall perform the 1 time power-on alert  
to indicate that it has been turned on.  
Cloning  
Frequencies and functions can be programmed from radio to radio by using a cloning cable.  
Password  
If the password function is enabled, (dealer programmable) the user must enter a password for  
the radio to become operational. At this time you can enter the password code by using the  
EMG/PTT/MON/OPTION button in the correct sequence. Four button presses are required to  
enter the code. If the code is not correct, the LED will blink red and there will be a double beep  
repeated. To disable the password function radio must be reprogrammed by an authorised Maxon  
dealer.  
Scanning  
Scanning is a Dealer programmable feature that allows you to monitor a number of channels.  
Your Dealer will help you define a scanning mode and your channel "scan list".  
Normal Channel Scan  
Once the scan list has been established, initiate scanning by pressing the scan key or holding the  
monitor button and rotate the channel switch to scan the enabled channels. Then the Green LED  
flashes to confirm the scanning.  
Page 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
User Manual  
S5  
If a conversation is detected on any of the channels in the scan list, the radio will stop on that  
channel and you will be able to hear the conversation.  
If programmed for normal scan TX, you will be able to transmit on that active channel during the  
programmable scan delay time. (The scan delay time is the amount of time the radio will stay on  
that channel once activity has ceased. Dealer programmable, 4-7 seconds is typical). The radio  
will resume scanning once the scan delay time has expired, and will continue to scan until the  
channel is changed. The LED will flash green.  
When in scan mode, if power is switch off and on, the radio reverts back to "scanning"  
automatically.  
Nuisance Scan Delete  
If there are any unwanted signals on any of the channels being scanned, they can be temporarily  
removed from the scan list. When the scanning feature has locked onto the unwanted signal  
simply press the monitor button. this will delete that channel from the scan list. When the radio is  
switched off and back on the channel is restored in the scan channel list.  
Priority Channel Scan  
A single channel may be programmed as the "Priority" channel. The radio will constantly monitor  
this channel while scanning. If a call is detected on the priority channel, the radio will  
automatically move to, and remain on, the priority channel activity takes precedence over all  
other conversations.  
Fixed Key  
PTT (Press to Talk)  
1. Press and Hold to transmit. Release to enter the receive mode.  
2. Power on with press and holding PTT Key to see software version.  
MONITOR  
Releases the squelch and tone circuit to check whether the channel is busy.  
OPTION  
Short pressing:  
Enable/disable scan  
Look Back channel edit  
EMG  
Transmits EMG ID 5 times and generate warning audio alert for a duration of 7 secs.  
English  
Page 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
User Manual  
S5  
Service Information  
Service  
Do not tamper with internal adjustments as this may cause damage to the equipment and will  
invalidate the warranty.  
There are no user serviceable items inside the radio. It is recommended that you return your  
radio to a qualified Maxon dealer for any service or repairs.  
Recycling/Disposal of Batteries  
The battery should be recycled at the end of it's useful life. Under various state or local laws,  
such batteries must be recycled or disposed of properly and cannot be dumped in landfills or  
incinerators.  
For further information on how to safely dispose of your used batteries, contact your Maxon  
Dealer.  
Maintenance  
Your S5 Radio is designed to be maintenance free. To keep your radio in good working condition:  
Clean external surfaces with a clean cloth dampened in a solution of dishwasher detergent diluted  
in water.  
Apply the solution sparingly to avoid any moisture leaking into cracks and crevices. Do not  
submerge the radio.  
Use a non-metallic brush to dislodge stubborn particles, if necessary.  
Dry the surface thoroughly with a soft, lint free cloth.  
DO NOT use solvents or spirits for cleaning – they may permanently damage the housing.  
Clean the battery contacts on the back of the radio with a lint free cloth to remove dirt, grease, or  
other foreign material that may impede good electrical contact.  
Limited Warranty  
Maxon shall have no obligation to make repairs or to cause replacement required which result  
from normal wear and tear or necessitated in whole or in part by damage, fault or negligence of  
the user, improper or unauthorized alterations, repairs to the Product, use of the Product in a  
manner for which it was not designed, or by causes external to the Product. This warranty is void  
if the serial number is altered, defaced or removed.  
Maxon's sole obligation hereunder shall be to repair or replace the Product covered in the agreed  
warranty.  
Page 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
User Manual  
S5  
CH-SL1000-02 Desktop Charger  
Product description  
The CH-SL1000-02 is the standard charger for Maxon's S5 two-way radio batteries.  
The charger has been designed to fully charge only the Li-ion, 1500mAh battery, the front  
charging slot charges a battery while connected to the radio, the back charging slot charges a  
battery that has been removed from the radio.  
For use only with power supply manufacturer: maxoncic Model: S5  
Use only power supplies listed in the user-instructions.  
Orientation  
Plug the AC adapter cable into the adapter jack locked on the rear of charger.  
Plug the AC adapter into an AC outlet.  
Page 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
User Manual  
S5  
Operating Instructions  
ƒ
ƒ
ƒ
ƒ
Remove the charger base and AC adapter from the packaging.  
Plug the AC adapter cable into the adapter jack located on the rear of the charger.  
Plug the AC adapter into an AC outlet  
Your charger is now ready to begin charging  
Charging starts automatically when the radio/battery is placed into the charger cup. The charging  
time is dependent upon the charge status of the battery.  
Lighting color  
Red  
Description  
During charging  
Green  
Fully charged  
Extreme cold (under -10°C; 14°F)  
Extreme heat (over +60°C; 140°F)  
Error  
Blinking orange  
Blinking red  
NOTE: If your battery seems to have no capacity even after being fully charged, completely  
discharge it, then fully charge it again. If the battery still does not retain a charge, new batteries  
must be replaced.  
Safety information  
To reduce the risk of shock or injury, familiarize yourself with the correct and safe operating  
procedures defined in this manual. Only charge Maxon's batteries in this charger – other battery  
types may burst causing personal injury or damage to the charger, battery or radio.  
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
The CH-SL1000-02 desktop charger is rated for indoor use only.  
Do not disassemble the charger; incorrect reassembly can cause fire or electric shock.  
Do not pull output plug with excessive force.  
Do not use the charger when it is covered by objects which impede heat dispersal.  
Connect the supplied Maxon adapter only to the voltage supply as specified on it's label.  
Unplug the AC adapter from the wall outlet before attempting inspection or cleaning of the  
charger.  
ƒ
Do not use solvents such as benzene or paint thinner to clean the charger.  
MEMO  
Page 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
User Manual  
S5  
S5 PMR446  
This product is marked with  
0678  
in accordance with the Class 1 product requirement specified in the R&TTE Directive 1999/5/EC.  
This equipment is intended for use in:-  
Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,  
Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal,  
Slovakia, Slovenia, Spain, Sweden, United Kingdom, Iceland, Liechtenstein, Norway, Switzerland,  
Bulgaria, Romania & Turkey.  
and is license exempt.  
We hereby declare that the above named product is in conformity to all the essential  
requirements of Directive 1999/5/EC.  
Con la presente si dichiara che il prodotto sopra menzionato è conforme ai requisiti essenziali  
della Direttiva 1999/5/CE.  
Declaramos que el producto mencionado más arriba cumple todos los requisitos esenciales de la  
Directiva 1999/5/CE.  
Wir möchten hiermit bekanntgeben, daß das oben genannte Produkt in Übereinstimmung mit  
allen erforderlichen Bedürfnissen der 1999/5/EC Direktive seht  
Nous déclarons que le produit référencé ci-dessus satisfait aux exigences  
R&TTE 1999/5/EC qui lui sont applicables.  
Nous déclarons que le produit référencé ci-dessus satisfait aux exigences  
R&TTE 1999/5/EC qui lui sont applicables.  
Maxon House, Cleveland Road,  
Hemel Hempstead, Hertfordshire,  
HP2 7EY, United Kingdom  
Tel: +44 (0)1442 267 777  
Fax: +44 (0)1442 215 515  
Page 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  

La Crosse Technology Battery Charger BC 900 User Manual
Learning Resources Telephone Accessories LER 0935 User Manual
Life Fitness Elliptical Trainer 95XEZ 0XXX 04 User Manual
Link electronic Stereo Amplifier PRC 970 User Manual
Lopi Indoor Fireplace Clean Face Gas Fireplace User Manual
Mackie Home Theater System HR824 MK2 User Manual
Magnavox Flat Panel Television 20MF500T User Manual
M Audio Electronic Keyboard Digital Piano User Manual
Maytag Clothes Dryer MEDZ600TB0 User Manual
MB QUART Car Speaker PWE 302 User Manual