High Performance
V.34/V.42bis
28,800 BPS Internal
Plug and Play
FAX/Voice/Data
Modem
Featuring Advanced Full-
Duplex Speakerphone
Functions
User's Manual
Part#MAN080Rev. 1.0
SF-1128HV/R16-PnP
Download from Www.Somanuals.com. All Manuals Search And Download.
Section One - Introduction
This 28.8 Kbps Plug and Play FAX/Voice/Data
Speakerphone Modem connects your computer to all
popularhighspeedmodemsavailabletoday.Yournew
modemfeaturesadvancedspeakerphonefunctionsfor
hands-freevoicecommunicationandiscompatiblewith
Plug and Play (PnP) systems for simplified installation
andconfiguration.Thismanualdescribesthehardware
installation procedures for your new modem product.
AdditionalinformationonATcommandsandS-registers
isprovidedsothatyoursystemcanbecustomizedfora
particularoperatingenvironment.
Section Two - Installation
This section will provide step by step instructions
on how to install your new 28.8 Kbps FAX/Voice/Data
modem. Installation of this modem product is a three-
stepprocessconsistsof1)actualhardwareinstallation,
2) plug and play configuration, and 3) communication
softwareinstallationandconfiguration.
2.1 Unpacking Your Modem
Becertainthatyouhavealltheitemslistedbelow.
Thispackagecontains:
• A modem
•Atelephonecable
•User'smanual
•Softwareuser'smanual
•Softwareforthemodem
2.2 What You Need
Youwillneed:
1. Aphillips-headscrewdriver
2. A) A Plug and Play enabled Operating System
(e.g., Windows 95),
or
B) APlugandPlayRevision1.0acompliantPC.
Proceed to Section 2.3 now if you have every-
thingrequired.
If you have neither 2A or 2B above, you have two
optionstoprovidePlugandPlayfunctionalitytoyourPC.
1. Install Windows 95
1
Download from Www.Somanuals.com. All Manuals Search And Download.
or,
2. If running DOS or Windows 3.x, configure the
modem using the included modem driver. Instructions
forinstallingthisdriverareincludedinthetextfilecalled
README.1ST on the Windows 95 driver disk.
TheREADME.1STfilecanbeviewedbyloadingit
intoanywordprocessoror anytexteditor(i.e.DOSEDIT,
NOTEPAD). It may also be viewed by using the DOS
TYPEcommand.Refertoyourwordprocessormanual
orDOS/Windowsreferencesforinformationonloading
textfiles.
2.3 Hardware Installation
Installation of this modem
Figure 2-1
Expansion
Slots
requiresopeningandmanipulat-
ing your PC. Exercise caution at
all times when working with AC
powered and static-sensitive
equipment. Turn off and unplug
your PC before installation. Dis-
charge any static electricity from
your body by touching any bare
metal surface of the PC system,
such as its power supply cover.
1. Turnoffandunplugyourcom-
puter from the AC outlet.
2. Remove your computer's
cover(refertoyourcomputer's
owner'smanual).
Figure 2-2
Back
Plate
PHONE
3. Selectanyavailablehalf-card
slot,andthenremovetheslot
cover (refer to Figure 2-1).
4. Carefullyslidetheinternalmo-
dem into the slot you have
chosen, applying even pres-
sure until the modem is com-
pletelyseatedintheslot.
5. Fasten the retaining bracket
with the screw from the slot
cover.Makesurethemodem
is properly aligned. Store the
slot cover for future use.
LINE
MIC
SPK
2
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Replace the computer cover and plug in your com-
puter.
7. Connectthetelephonecablefromthemodem'sLINE
connectortothetelephonewalljack.SeeFigure2-2.
8. Optionally,connectyourtelephonetothemodem's
PHONEconnector.
9. Optionally,connectyourmicrophonetothemodem's
MIC jack.
10. Optionally,connectyourspeakersintothemodem's
SPK jack.
11. Turn your computer on. Your modem is now in-
stalled.
2.4 Hardware Configuration (Plug and Play)
YourmodemisconfiguredusingthePlugandPlay
(PnP) capabilities of your computer. Plug and Play is a
set of specifications that define the ability for the com-
puter hardware and operating system to automatically
configureallcompliantdevicesthatareinstalled,reliev-
ing the user of the need to determine which addresses
andinterruptstouseforeachdevice.ConsultyourPC's
owner's manual to determine if it is PnP Revision 1.0a
compliant.YoumostlikelyhaveaPlugandPlayRevision
1.0a compliant system if it was purchased after June
1994 or if the BIOS is dated after June 1994.
Proceedtooneofthefollowingsections,depending
onyoursystem'sconfiguration:
• Section 2.4.1 if you are running Windows
95 (with or without a Plug and Play PC)
• Section 2.4.2 if you are running Windows
3.1x or DOS on a PnP-compliant PC.
• Section 2.4.3 if you are running Windows
3.1x on a non-PnP PC.
2.4.1 ConfiguringinWindows95
When Windows 95 starts for the first time after
cardinstallation,itdetectsthemodemanddisplaysthe
NewHardwareFounddialogbox.
Under New Hardware Found, when asked to
“Select which driver you want to install for your new
hardware,” click on “Driver from disk provided by hard-
waremanufacturer.”Click“OK.”
3
Download from Www.Somanuals.com. All Manuals Search And Download.
The Install From Disk dialog box now instructs
youto“Insertthemanufacturer'sinstallationdiskintothe
drive selected, and then click OK.” Insert the modem's
Utility diskette into the disk drive and type A:\ (or B:\ if
inserted in drive B) in the “Copy manufacturer's files
from:” box. Click “OK.”
Windows95mayrequestitsowninstallationdisks
forsomefiles.InserttheWindows95disksasrequired.
When all necessary files are copied, the modem is
configured. Windows95willassignthemodemaCOM
port and IRQ line.
Windows95communicationpackageswillrecog-
nizethemodembyname. Windows3.1xcommunication
packages running under Windows 95 need to access
the modem via the COM port designation given to the
modem. This can be found by running Control Panel
(Start|Settings|Control Panel), double-clicking Mo-
dems,selectingthemodemandclickingon“Properties”
under the General tab. Note which COM port is being
used by the modem. Proceed to Section 2.5, Software
Installation/Configuration.
2.4.2 ConfiguringinaPlugandPlaySystemwithout
Windows95
When this modem is installed in a Plug and Play
system without Windows 95, the computer's BIOS will
assign a COM port and IRQ line to the modem.
ProceedtoSection2.5,SoftwareInstallation/Con-
figuration.
2.4.3 Configuring in a Non-Plug and Play System
ComputerswithoutnativePlugandPlaycapabili-
tiesrequiretheuseoftheincludedmodemdriver.Ifyou
have not already installed this driver, refer to the file
README.1STontheWindows95driverdiskforinstal-
lationandconfigurationinstructions. Oncethedriveris
installed the modem is enabled and configured during
systemboot-up.TheCOMportandIRQsettingsthatare
assignedtothemodemwillbedisplayedonthescreenas
thedriverisloaded.
Configure Windows 3.1x to properly recognize
these modem settings by opening PROGRAM
4
Download from Www.Somanuals.com. All Manuals Search And Download.
MANAGER|MAIN|CONTROLPANEL,clickonPORTS
andfollowWindows3.1xuser'smanualinstructionson
configuringtheinstalledmodemCOMport.
ProceedtoSection2.5,SoftwareInstallation/Con-
figuration.
2.5 Software Installation and Configuration
You are now ready to install and configure the
communicationsoftware.Refertoyoursoftwaremanual
forinstallationprocedures.
Wesuggestthefollowingcommunicationparam-
eterswhenyoufirstuseyourdatacommunicationsoft-
ware. Consult the software manual for information on
usingtheseandotherparameters/features.
38,400 bps; 8 data bits; no parity; 1 stop bit;
RTS/CTSflowcontrolsetto“on;”initialization
string:AT&F
Wesuggestthata“GenericClass2”or“Generic
Class 1” modem type should be selected in your fax
software,anda“GenericRockwell”modemtypeshould
beselectedinyourVoicesoftware.
Note that your software must be configured to
communicate with the modem on the same COM port
and IRQ line used by the modem.
2.6 Using the Fax, Voice, and Speakerphone
Capabilities of the Modem
Your modem has built-in advanced FAX, Voice,
andFullDuplexSpeakerphonefunctions.Pleaseconsult
yourFAX/Voice/Speakerphonesoftwaremanualabout
proceduresonusingthesefeatures.
Voicefunctionsincluderecordingandplaybackof
voiceprompts(files).Youmayrecordorplaybackvoice
withyourmodembyattachingatelephonetotheRJ-11
jackmarked“PHONE”orbyattachingamicrophoneto
the MIC jack and a speaker to the SPK jack located on
thebackofthemodembracket.Followinstructionsinthe
FAX/Voice/Speakerphone software on recording and
playbackofvoiceprompts.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2.7 Testing Your Modem After Installation
Inordertotestyourmodemyoushouldbefamiliar
withyourcommunicationsoftware.Loadandsetupyour
communicationsoftwareandenterinto“terminalmode.”
Make sure that the COM Port and IRQ settings of the
modem match the software. Type AT on your terminal
screenandpressENTER.Youmaysee“AT”,“AATT”or
nothing on the screen. In any case, the modem should
respondwithanOKor0.Ifitdoesnot,eitherthemodem
maynothavebeeninstalledproperlyorthesoftwarehas
notbeenproperlyconfigured.ReviewSections2.2-2.5
and be certain that the modem and the software have
beenproperlyinstalled.Ifrequired,refertoSection6for
additional troubleshootinginformation.
2.8 Using Your Modem
The communication software included with your
modem product provides a user friendly interface to
accessthefax,voiceanddatafunctionsofyourmodem.
This software should be sufficient for all of your
communicationneeds.Theremaybetimeswhenyou
need to access the modem manually via modem com-
mands.ReadSection3forasummarydescriptionofthe
modem command set before manually accessing the
modem.Youmaywanttoreadthesoftwaremanualfirst,
however, as the software may already provide a user
friendlymethodofaccessingthefunctionsyouneed(i.e.
dialingoransweringcalls).
2.9 Where To Go From Here
Youshouldfamiliarizeyourselfwiththefunctions
availablefromtheincludedsoftwarebyreadingitsmanual.
You will be accessing most, if not all, of the modem's
functionsfromthis software.Youmayalsouseanyother
commerciallyavailable communicationsoftwarewiththe
modem. Read Section 3 ONLY if you are interested in
accessing the modem manually, and not through the
included software. Section 4 and 5 contain reference
material, and can be skipped. If you have difficulties
getting your modem to work, read Section 6 - Trouble-
shootingtofindanswerstocommonlyaskedquestions
andproblems.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Three - AT Command Set
3.1 Executing Commands
Commandsareacceptedbythemodemwhileitis
in Command Mode. Your modem is automatically in
CommandModeuntilyoudialanumberandestablisha
connection. Commands may be sent to your modem
fromaPCrunningcommunicationsoftwareoranyother
terminaldevices.
Yourmodemiscapableofdatacommunicationat
rates of: 300, 1200, 2400, 4800, 9600, 14400, 19200,
28800,38400,57600,and115200bps.Makesureyour
COM port baud rate settings in your communications
software is set to one of the above speeds.
3.2 Command Structure
Allcommandssenttothemodemmustbeginwith
AT and end withENTER. All commands may be typed
ineitherupperorlowercase,butnotmixed.Tomakethe
commandlinemorereadable, spacesmaybeinserted
between commands. If you omit a parameter from a
command that requires one, it is just like specifying a
parameterof0.Example:
ATH[ENTER]
This command causes your modem to hang up.
3.3 Basic AT Commands
In the following listings, all default settings are
printed in bold text.
Command
Function
A
Manuallyanswerincomingcall.
A/
Repeat last command executed. Do not
precedeA/withATorfollowwithENTER.
B_
B0
CCITTmode
B1
Bellmode
D_
0 - 9, A-D, # and *
lastnumberredial
pulsedialing
touch-tonedialing
wait for second dial tone
L
P
T
W
7
Download from Www.Somanuals.com. All Manuals Search And Download.
,
pause
@
!
;
wait for five seconds of silence
flash
returntoCommandModeafterdialing
DS=n
Dial one of the four telephone numbers
(n=0-3)storedinthemodem’snon-volatile
memory.
E_
+++
H_
I_
E0
E1
Commandsarenotechoed
Commandsareechoed
Escape Characters - Switch from Data
ModetoCommandMode
H0
H1
Forcemodemon-hook(hangup)
Forcemodemoff-hook(makebusy)
I0
I1
I2
I3
I4
Displayproduct-identificationcode
Factory ROM checksum test
Internalmemorytest
FirmwareID
ReservedID
L_
L0
L1
L2
L3
Lowspeakervolume
Lowspeakervolume
Mediumspeakervolume
Highspeakervolume
M_
M0
Internalspeakeroff
M1
Internal speaker on until carrier
detected
M2
M3
Internalspeakeralwayson
Internal speaker on until carrier detected
andoffwhiledialing
N_
N0
DisableAutoscanmode
N1
EnableAutoscanmode
O_
O0
O1
ReturntoDataMode
Return to Data Mode and initiate an
equalizerretrain
P
Set Pulse dial as default
Q_
Q0
Modemsendsresponses
Q1
Modemdoesnotsendresponses
Sr?
Sr=n
T
Readanddisplayvalueinregisterr.
Set register r to value n (n = 0-255).
Set Tone Dial as default
V_
V0
Numericresponses
V1
Wordresponses
8
Download from Www.Somanuals.com. All Manuals Search And Download.
W_
W0
W1
Report DTE speed only
Reportlinespeed,errorcorrectionprotocol,
and DTE speed.
W2
X0
ReportDCEspeedonly
X_
Hayes Smartmodem 300 compatible
responses/blinddialing.
X1
SameasX0plusallCONNECTresponses/
blinddialing
X2
X3
Same as X1 plus dial tone detection
Same as X1 plus busy detection/blind
dialing
X4
All responses and dial tone and busy
signaldetection
Y_
Z_
Y0
Modem does not send or respond to
breaksignals
Modemsendsbreaksignalforfourseconds
beforedisconnecting
Y1
Z0
Z1
Resetandretrieveactiveprofile0
Resetandretrieveactiveprofile1
3.4 Extended AT Commands
&C_
&C0 Force Carrier Detect Signal High (ON)
&C1 TurnonCDwhenremotecarrierispresent
&D_
&D0 Modem ignores the DTR signal
&D1 Modem returns to Command Mode after
DTRtoggle
&D2 Modemhangsup,returnstotheCommand
ModeafterDTRtoggle
&D3 ResetsmodemafterDTRtoggle
&F_
&G_
&F
Recallfactorydefaultconfiguration
&G0 Guard tone disabled
&G1 Guardtonedisabled
&G2 1800 Hz guard tone
&K_
&K0 Disableflowcontrol
&K3 EnableRTS/CTShardwareflowcontrol
&K4 EnableXON/XOFFsoftwareflowcontrol
&K5 EnabletransparentXON/XOFFflowcontrol
&K6 Enable both RTS/CTS and XON/XOFF
flowcontrol
&L_
&M_
&P_
&L0 Modem is set up for dial-up operation
&M0 Asynchronousoperation
&P0 USsettingforoff-hook-to-on-hookratio
&P1 UK and Hong Kong off-hook-to-on-hook
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ratio
&P2 Sameas&P0settingbutat20pulsesper
minute
&P3 Sameas&P1settingbutat20pulsesper
minute
&R_
&S_
&T_
&R0 Reserved
&R1 CTS operates per flow control
requirements
&S0 Force DSR Signal High (ON)
&S1 DSR off in command mode, on in on-line
mode
&T0 Ends test in progress
&T1 PerformLocalAnalogLoopbackTest
&T3 PerformLocalDigitalLoopbackTest
&T4 Grant Remote Digital Loopback Test
request by remote modem
&T5 Deny Remote Digital Loopback Test
request
&T6 PerformaRemoteDigitalLoopbackTest
&T7 PerformaRemoteDigitalLoopbackTest
andSelf-Test
&T8 PerformLocalAnalogLoopbackTestand
Self-Test
&V
&V
DisplaysActiveandStoredProfiles
&W_
&W0 Stores the active profile as Profile 0
&W1 Stores the active profile as Profile 1
&Y_
&Y0 Configuration Profile 0 active upon
Power on or reset
&Y1 ConfigurationProfile1activeuponPower
on or reset
&Zn=x n=0-3 Store phone number x into non-volatile
RAM
%E_
%E0 Disableauto-retrain
%E1 Enableauto-retrain
%L
Displaylinesignallevel
Displaylinesignalquality
%Q
+MS?
Displays the current Select Modulation
settings
+MS=?
Displays a list of supported Select
Modulationoptions
+MS=a,b,c,d
Selectmodulationwhere:a=0,1,2,9,10,
11, 64, 69, 74; b=0-1; c=300-28800; and
10
Download from Www.Somanuals.com. All Manuals Search And Download.
d=300-28800. A, b, c, d default=11, 1,
300, 28800. Parameter “a” specifies the
modulationprotocoldesiredwhere:0=V.21,
1=V.22, 2=V.22bis, 3=V.23, 9=V.32,
10=V.32bis, 11=V.34, 64=Bell 103,
69=Bell212,and74=VFC.Parameter“b”
specifies automode operations where:
0=automode disabled, 1= automode
enabledwithV.8/V.32AnnexA.Parameter
“c”specifiestheminimumconnectiondata
rate(300-28800).Parameter“d”specifies
themaximumconnectionrate(300-28800).
#CID=n n=0 DisableCallerID
n=1 Enables Caller ID with formatting (date,
time,number,name)
n=2 EnablesCallerIDwithoutformatting
#CID?
DisplayscurrentCallerIDmode
#CID=?
ReturnsCallerIDcapabilitiesofmodem.
3.5 MNP/V.42/V.42bis Commands
%C_
%C0 Disable MNP Class 5 and V.42bis data
compression
%C1 Enable MNP Class 5 data compression
only
%C2 EnableV.42bisdatacompressiononly
%C3 Enable MNP Class 5 and V.42bis data
compression
&Q_
\A_
&Q0 Direct data link only (same as \N1)
&Q5 V.42 data link with fallback options
&Q6 Normal data link only (same as \N0)
\A0
64-charactermaximumMNPblocksize
128-character maximum MNP block
size
\A1
\A2
\A3
192-charactermaximumMNPblocksize
256-charactermaximumMNPblocksize
\Bn
\Kn
\N_
Send a 1/10 second line break to the modem,
where n = 1 to 9. At normal connect, the default
is 3
Set break control, where n= 0 to 2. The effect of
thiscommanddependsonthemodem’soperating
condition. Defaultis1.
\N0
\N1
Normaldata-linkonly
Directdata-linkonly
11
Download from Www.Somanuals.com. All Manuals Search And Download.
\N2
\N3
\N4
\N5
V.42 or MNP data link only
V.42/MNP/Normaldatalink
V.42datalinkonly
MNPdatalinkonly
3.6 Fax Class 1 Commands
+FAE=n
+FCLASS=n
+FRH=n
+FRM=n
+FRS=n
+FTH=n
+FTM=n
+FTS=n
Data/FaxAutoAnswer
ServiceClass
ReceivedatawithHDLCframing
Receivedata
Receivesilence
Transmit data with HDLC framing
Transmitdata
Stoptransmissionandwait
3.7 Fax Class 2 Commands
+FCLASS=n
+FAA=n
+FAXERR
+FBOR
+FBUF?
+FCFR
+FCON
+FCIG
ServiceClass
AdaptiveAnswer
FaxErrorValue
Phase C Data Bit Order
Buffer Size
IndicateConfirmationtoReceive
FacsimileConnectionResponse
Setthepolledstationidentification
Reportthepolledstationidentification
CapabilitytoReceive
+FCIG:
+FCR
+FCR=
+FCSI:
+FDCC=
+FDCS:
+FDCS=
+FDIS:
+FDIS=
+FDR
+FDT=
CapabilitytoReceive
ReporttheCalledStationID
DCECapabilitiesParameters
ReportCurrentSession
CurrentSessionResults
ReportRemoteIdentification
CurrentSessionsParameters
BeginorContinuePhaseCReceiveData
DataTransmission
+FDTC:
+FET:
+FET=n
+FHNG
+FK
Reportthepolledstationcapabilities
PostPageMessageResponse
TransmitPagePunctuation
CallTerminationswithStatus
SessionTermination
+FLID=
+FLPL
Local ID String
Documentforpolling
+FMDL?
+FMFR?
+FPHCTO
+FPOL
IdentifyModel
IdentifyManufacturer
Phase C Time Out
Indicatespollingrequest
12
Download from Www.Somanuals.com. All Manuals Search And Download.
+FPTS:
+FPTS=
+FREV?
+FSPL
PageTransferStatus
PageTransferStatus
IdentifyRevision
Enablepolling
+FTSI:
Report the Transmit Station ID
3.8 Voice Commands
#BDR
#CID
SelectBaudRate
Enable Caller ID detection and reporting
format
#CLS
#MDL?
#MFR?
#REV?
#TL
SelectData,FaxorVoice/Audio
IdentifyModel
IdentifyManufacturer
IdentifyRevisionLevel
Audiooutputtransmitlevel
Query Buffer Size
Bits per sample (ADPCM or PCM)
BeepToneTimer
IdentifyCompressionMethod
Voicelineselect
Ringbackgoesawaytimer
Ringbacknevercametimer
VoiceReceiveMode
#VBQ?
#VBS
#VBT
#VCI?
#VLS
#VRA
#VRN
#VRX
#VSDB
#VSK
#VSP
#VSR
#VSS
#VTD
#VTM
#VTS
#VTX
Silencedeletiontuner
Buffer skid setting
Silencedetectionperiod
Samplingrateselection
Silencedeletiontuner
DTMFtonereportingcapability
Enabletimingmarkplacement
Generatetonesignals
Voicetransmitmode
Section Four - S Registers
Your modem has 41 registers, designated S0
through S95. Table 4-1 shows the registers, their func-
tions,andtheirdefaultvalues.Someregisterscanhave
their values changed by commands. If you use a com-
mandtochangearegistervalue,thecommandremains
in effect until you turn off or reset your modem. Your
modem then reverts to the operating characteristics
specifiedinitsnon-volatilememory. RefertoSection3
for information on how to use the AT commands to
manipulatetheSregisters.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-1 S - Registers
Function Range/units Default
Register
S0
S1
Auto-answer Ring
Ring counter
0-255 /rings
0-255 /rings
0
0
S2
S3
S4
S5
S6
S7
S8
Escape code character
Carriage return character
Line feed character
Backspace character
Dial tone wait time
0-127/ASCII
0-127/ASCII
0-127/ASCII
0-32, 127 /ASCII
2-255 /seconds
1-255 /seconds
0-255 /seconds
43
13
10
8
2
50
2
Remote carrier wait time
Comma pause time
S9
Carrier detect response time 1-255 /0.1 second
6
S10
S11
S12
S13
S14
Carrier loss time
Touch-tone dialing speed
1-255 /0.1 second
50-255 /milliseconds 95
14
Escape character guard time0-255 /0.02 second
Reserved
Echo, response, dialing,
originate/answer
Reserved
Modem tests
Reserved
Length of modem tests
50
Bit-mapped register
S15
S16
S17
S18
Bit-mapped register
0-255 /seconds
0
0
S19-20 Reserved
S21
CTS, DTR, DCD, DSR and Bit-mapped register
Long Space Disconnect
S22
S23
Speaker and response
Remote Digital Loopback
Request, data rate, and parity
Sleep mode timer
Data Terminal Ready delay 0-255 /0.01 second
RTS to CTS delay interval 0-255 /0.01 second
Asynchronous/Bell/CCITT Bit-mapped register
Modes
Bit-mapped register
Bit-mapped register
S24
S25
S26
S27
0-255 seconds
0
5
1
S28
S29
S30
S31
S32
S33
Reserved
Flash time
Disconnect timer
Autoscan, EC result code
XON character
0-255 /0.01second
0-255 /10 seconds
Bit-mapped register
0-255/ASCII
0
0
17
19
XOFF character
0-255/ASCII
S34-35 Reserved
S36
S37
S38
S39
S40
S41
LAPM failure options
Connection speed
Hang-up delay
Flow control options
MNP options, break types
Compression, retrain, DCE Bit-mapped register
flow control, block modes
Bit-mapped register
Bit-mapped register
0-255 /seconds
Bit-mapped register
Bit-mapped register 105
7
0
20
3
3
S42-45 Reserved
S46
S47
S48
Data Compression control 136 or 138
Reserved
138
7
V.42 negotiation options
0, 7, or 128
14
Download from Www.Somanuals.com. All Manuals Search And Download.
S49-81 Reserved
S82
Break options
3, 7, or 128
128
S83-85 Reserved
S86
Connection failure code
0, 4, 5, 9, 12, 13, 14
*
S87-S90Reserved
S91
S92
S95
Transmit attenuation
Faxattenuation
Extended result code optionsBit-mapped register
0-15/dBm
0-15/dBm
10
10
Section Five - Result Codes
OK
RING
ERROR
NO DIALTONE
NO ANSWER
CONNECT 2400
CONNECT 9600
CONNECT 12000
CONNECT 19200
CONNECT 57600
0
2
4
6
8
CONNECT
1
3
5
7
9
11
13
15
17
19
NO CARRIER
CONNECT 1200
BUSY
CONNECT 600
10 CONNECT 4800
12 CONNECT 7200
14 CONNECT 14400
16 CONNECT 38400
18 CONNECT 115200
CONNECT 1200TX/75RX 22 CONNECT 75TX/1200RX 23
FAX
33 DATA
35
44
46
48
50
52
56
64
CARRIER 300
CARRIER75/1200
CARRIER 2400
CARRIER 7200
CARRIER 12000
CARRIER21600
CARRIER26400
40 CARRIER1200/75
45 CARRIER 1200
47 CARRIER 4800
49 CARRIER 9600
51 CARRIER14400
55 CARRIER24000
57 CARRIER28800
COMPRESSION:CLASS5 66 COMPRESSION:V.42BIS 67
COMPRESSION:NONE
PROTOCOL: LAPM
+FCERROR
69 PROTOCOL: NONE
77 PROTOCOL: ALT
+F4
70
80
Section Six - Troubleshooting
Thissectiondescribessomeofthecommonprob-
lemsyoumayencounterwhileusingyourmodem.Ifyou
cannotresolveyourdifficultyafterreadingthischapter,
contactyourdealerorvendorforassistance.
Modem does not respond to commands.
1. Makesurethecommunicationsoftwareisconfiguredto
“talk” to the modem on the correct COM port and IRQ
setting(sameCOMportandIRQsettingasthemodem).
Your communication software must know which ad-
dressyourmodemisusinginthesysteminordertopass
datatoit.Similarly,IRQsettingsmustbesetcorrectlyto
15
Download from Www.Somanuals.com. All Manuals Search And Download.
receivedatafromthemodem.
2. Makesurethatyourmodemisinitializedcorrectly.Your
modem may have been initialized to not display re-
sponses.Youmayfactory-resetthemodembyissuing
AT&FandpressENTER.Thefactorydefaultallowsthe
modemtodisplayresponsesafteracommandhasbeen
executed.
Modem does not dial.
1. Makesurethemodemisconnectedtoaworkingphone
line.Replacethemodemwithaworkingphonetoensure
that the phone line is working.
2. Make sure the phone line is connected to the jack
marked“LINE.”Incorrectconnectionpreventsthemo-
dem from operating properly. Refer to Section 2.3 for
modemconnectioninstructions.
Modem dials but does not connect.
1. Make sure the IRQ setting is identical on both the
modemandthesoftware.Modemandsoftwaremustbe
configuredidentically.
2. Makesurethephonelineisworkingproperly. Replace
themodemwitharegularphoneanddialthenumber.If
thelinesoundsnoisy,youmayhavedifficultyconnecting
totheremotedevice.
Modem makes a connection but no data
appears on your screen.
1. Make sure the correct data format (data bits, stop bits,
and parity bits) and flow control (RTS/CTS) are being
used.
2. Makesurethecorrectterminalemulationmodeisbeing
used(seecommunicationsoftwaremanual).
High pitch tone is heard whenever you
answer the phone.
1. Make sure Auto-Answer is turned off. Your modem is
factoryconfiguredtoNOTauto-answer.IssueAT&Fto
factoryresetyourmodem.
Modem experiences errors while
communicating with a remote modem.
1. Makesuretheremotesystemandyourmodemusethe
samecommunicationparameters(speed,parity,etc.).
2. Make sure RTS/CTS hardware flow control is enabled
andXON/XOFFsoftwareflowcontrolisdisabledinthe
16
Download from Www.Somanuals.com. All Manuals Search And Download.
communicationsoftware.
3. Make sure the data speed is not faster than your
computer's capability. Most IBM compatibles are ca-
pableof19,200bpsunderDOSandWindows.Operat-
ing at higher speeds under Windows requires a faster
CPU (386/486 or better), a high performance replace-
ment Windows 3.1x comm.drv, or Windows 95.
Modem experiences bursts of errors or
suddenly disconnects while communicating
with a remote modem.
1. Make sure Call Waiting is turned off.
2. Makesurethephonelinedoesnotexhibitexcessnoise.
Modem exhibits poor voice record or
playback.
1. Make sure the correct modem type is selected in the
Voice/FAXsoftware.Use“GenericRockwell”orsimi-
larselection.
Section Seven - Support and Service
Intheunlikelyeventyouexperiencedifficultyinthe
use of this product, we suggest you: (1) consult the
Troubleshootingsectionofthisguideand(2)consultwith
yourdealer.Toobtainserviceforthisproduct,followthe
Return Merchandise Authorization Procedure as out-
lined in the Warranty card.
Appendix A - Specifications
CommunicationStd. V.34, V.32bis, V.32, V.29, V.27ter,
V.22bis, V.23, V.22, V.21, V.17,
Bell212/103
DataCompression: V.42bis/MNP5
ErrorCorrection:
HostInterface:
COM ports:
V.42/MNP2-4
16 bit PC bus
1, 2, 3, 4
IRQ lines:
FAXGroup:
3, 4, 5, 7, 9, 10, 11, 12, 15
GroupIIISend/ReceiveStandard
FAXCommandset: EIA/TIA-578 Service Class 1, EIA/
TIA-SP2388 Service Class 2
Transmitlevel:
-11 dBm +/- 1 dB
ReceiverSensitivity: -39 dBm (V.34); -43 dBm (all other
protocols)
UART:
16550compatible
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Dataformat:
Power:
300-115200bps
0.75 W
Temperature:
CallerID:
0 to 55 degrees C (Operating)
Yes
PnP:
Revision1.0a
Speakerphone:
Full-duplexwithDSPecho
cancellation
Appendix B - Speaker Type Selection
Yourmodemsupportsbothmonoandstereospeakers.Use
jumper JP3 to select the speaker type. The modem is factory set
to use stereo speakers (jumper over both pins). If you use a mono
speaker, remove the jumper (See Figure B-1).
Figure B-1 Speaker Type Jumper JP3
STEREO
MONO
Appendix C - Notices
FCC Compliance
ThisequipmentcomplieswithPart68oftheFCCRules.Onthis
equipmentisalabelthatcontains,amongotherinformation,the
FCC registration number and Ringer Equivalence Number
(REN)forthisequipment.Youmust,uponrequest,providethis
information to your telephone company.
If your telephone equipment causes harm to the telephone
network, the Telephone Company may discontinue your ser-
vice temporarily. If possible, they will notify in advance. But, if
advance notice is not practical, you will be notified as soon as
possible. You will be informed of your right to file a complaint
with the FCC.
Your telephone company may make changes in its facilities,
equipment, operations, or procedures that could affect proper
operation of your equipment. If they do, you will be notified in
advance to give you an opportunity to maintain uninterrupted
telephoneservice.
TheFCCprohibitsthisequipmenttobeconnectedtopartylines
orcoin-telephoneservice.
Intheeventthatthisequipmentshouldfailtooperateproperly,
disconnecttheequipmentfromthephonelinetodetermineifit
is causing the problem. If the problem is with the equipment,
discontinue use and contact your dealer or vendor.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TheFCCalsorequiresthetransmitterofaFAXtransmissionbe
properlyidentified(perFCCRulesPart68,Sec.68.381(c)(3)).
FCC Class B Statement
This equipment has been tested and found to comply with the
limitsforaClassBdigitaldevice,pursuanttoPart15oftheFCC
Rules.Theselimitsaredesignedtoprovidereasonableprotec-
tion against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio fre-
quencyenergy,andifnotinstalledandusedinaccordancewith
theinstructions, maycauseharmfulinterferencetoradiocom-
munications.However,thereisnoguaranteethatinterference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorientorrelocatethereceivingantenna
• Increase the separation between the equipment and the
receiver
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
• Consultthedealeroranexperiencedradio/TVtechnicianfor
help
Notice: 1) Shielded cables, if any, must be used in order to
comply with the emission limits. 2) Any change or modification
not expressly approved by the Grantee of the equipment
authorization could void the user’s authority to operate the
equipment.
DOC Compliance Information
NOTICE:TheCanadianDepartmentofCommunicationslabel
identifiescertifiedequipment.Thiscertificationmeansthatthe
equipmentmeetscertaintelecommunicationsnetworkprotec-
tive, operational and safety requirements. The Department
does not guarantee the equipment will operate to the user’s
satisfaction.
Beforeinstallingthisequipment, usersensurethatitispermis-
sible to be connected to the facilities of the local telecommuni-
cations company. The equipment must also be installed using
anacceptablemethodofconnection. Thecustomershouldbe
aware that compliance with the above conditions may not
prevent degradation of service in some situations.
Repairstocertifiedequipmentshouldbemadebyanauthorized
Canadianmaintenancefacilitydesignatedbythesupplier.Any
repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications
19
Download from Www.Somanuals.com. All Manuals Search And Download.
company cause to request the user to disconnect the equip-
ment.
Users should ensure for their own protection that the electrical
ground connections of the power utility, telephone lines and
internal metallic water pipe system, if present, are connected
together.Thisprecautionmaybeparticularlyimportantinrural
areas.
Caution: Users should not attempt to make such connections
themselves,butshouldcontacttheappropriateelectricinspec-
tion authority, or electrician, as appropriate.
NOTICE: The Load Number (LN) assigned to each terminal
devicedenotesthepercentageofthetotalloadtobeconnected
to a telephone loop which is used by the device, to prevent
overloading. The termination on a loop may consist of any
combinationofdevicessubjectonlytotherequirementthatthe
sum of the Load Numbers of all the devices does not exceed
100.
UL Notice
Caution: This internal modem adapter is to be installed in UL
Listedcomputersonly,Alwaysdisconnectthemodemadapter
fromthetelephonesystemduringinstallationorwhenthecover
is removed from the computer.
First Edition
GZ/DR - Version 1.0
20
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
|