Marvel 6SBAR Beverage Center
Installation
Operation &
Maintenance
Instructions
Part of AGA Foodservice Group
Download from Www.Somanuals.com. All Manuals Search And Download.
Grounding Method: This product is factory
equipped with a power supply cord that has a three-
pronged grounded plug. It must be plugged into a
mating grounding type receptacle in accordance with
the National Electrical Code and applicable local
codes and ordinances (see figure 1). If the circuit
does not have a grounding type receptacle, it is the
responsibility and obligation of the customer to
exchange the existing receptacle in accordance with
the National Electrical Code and applicable local
codes and ordinances. The third ground prong
should not, under any circumstances, be cut or
removed. All U.L. listed refrigerated products are
equipped with this type of plug.
To start your appliance, use a screwdriver to turn the
control clockwise to the middle thermostat setting
(see figure 2). Once the beverage center is loaded,
allow at least 48 hours for the unit to stabilize before
making any adjustments to the initial setting.
Insert Wine Bottles: The wine rack roll-out shelf
holds eight bottles. See figure 3 for typical wine
bottle orientation.
Rear Bottles (Necks Facing Front)
Front Bottles (Necks Facing Rear)
How to Operate Your
Figure 3
Refrigerated Beverage Center
Note: Wine rack can be located at the middle or
bottom part of the cabinet interior. For red wines,
place wine shelf at bottom shelf position in the
cabinet. Then put a glass shelf in the next higher
position. For white and sparkling wines, put the
wine shelf on the middle shelf position in the cab-
inet. Place the remaining shelves as desired.
Also, there is a fixed, wooden, bottle cradle in the
bottom, step section of the cabinet. Six bottles of
wine may be stored there.
Set the Control: The total available temperature
range of the unit is from 39°F to the high sixties,
depending on the thermostat setting and location of
the cabinet. The middle range on the control is from
the mid-forties to the mid-fifties depending on ambient
Control Knob
temperature and location of
the cabinet. The tempera-
ture can be lowered or
raised by turning the control
clockwise or counterclock-
wise, respectively. As with
any refrigeration product,
(At bottom right
section of grille)
Loading Tips and
Suggestions for Wine Rack
Figure 2
there is a slight temperature variance at different loca-
tions within the cabinet. For example, the coolest area
will be in the rear of the middle of the cabinet.
Commodities on the top shelf will be 3° to 8° warmer.
This section and the bottom cabinet step section are
the warmest areas. Items in the front of the middle
shelves will be 1° to 4° warmer than the rear of the
shelves. Position your wine inventory accordingly on
your wine shelf.
The wooden, bottom bottle cradle may be removed for
storing "jug" wines. Just remove the two screws that
secure the cradle to the cabinet floor.
You can store magnum bottles and other large bottles
on any of the shelves (except for the top shelf) by
removing the shelf directly above them or placing the
shelf at a position allowing for proper clearance.
The glass shelves and fixed position wire rack are for
general beverage storage, such as beer and soft
drinks. Opened wine bottles and tall beverage con-
tainers may be stored on the glass shelf closest to the
cabinet top. Just lift the hinged section of the fixed
position upper wire rack to provide clearance for the
bottles and/or containers to stand upright.
Commodities on the top rack directly under the light will
be exposed to a slightly higher temperature when the
light is on. REMEMBER TO TURN OFF THE LIGHT
WHEN IT IS NO LONGER NEEDED.
Keep wines that you plan to use for everyday drinking
and entertaining on the front half of the racks where
labels are completely visible. Place wines for aging or
longer term storing in rear.
Do not pull out upper glass shelf when tall bottles are placed
upright through the opening in the hinged wire shelf. Doing
so may cause the tall, upright bottles to fall backwards.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Using the /16” hex-head driver, resecure the two
How to Clean and
Maintain Your beverage center
hex-head screws back into their original positions to
fasten the light tube housing assembly to the top of
the cabinet.
Condenser: The condenser tubing inside the cabinet
does not require frequent cleaning; however, satis-
factory cooling depends on adequate ventilation over
the coils. Be sure that nothing obstructs the required
air flow openings in front of the cabinet. At least once
or twice a year brush or vacuum lint and dirt from the
condenser for efficient performance by unscrewing
the grille on the bottom front of the cabinet.
Re-use the original two screws to secure the light tube
housing in place. Plug the beverage center into the
electrical socket. Check to see if the light tubes oper-
ate properly. Your light tube’s replacement is complete.
The light tubes are not covered by your guarantee. A
replacement light tube housing can be obtained from
your service provider or from Marvel Industries.
Cabinet: The painted cabinet can be washed with
mild soap and water and thoroughly rinsed with clear
water. Never use abrasive scouring powders.
What to do in
the Event of a Power Failure
Interior: Wash interior compartment with mild soap
and water. Do not use an abrasive powder, solvent,
polish cleaner or undiluted detergent.
Most power failures are corrected within two hours
and will not affect the unit’s temperature providing you
minimize the number of door openings while the
power is off. A gradual rise in temperature should not
have any adverse effect on your wine if power is out
for a longer period. If it is extremely hot, you may
want to move your wines to the coolest location you
can find until power is restored.
Glass Door: Use a glass cleaner or mild soap and
water and soft cloth to clean the glass door model.
Do not use any abrasive powders.
Door Gasket: The vinyl gasket may be cleaned with
mild soap and water, a baking soda solution or a mild
scouring powder.
Light Tube Replacement: WARNING! DISCONNECT
THE POWER CORD BEFORE ATTEMPTING LIGHT
TUBE HOUSING ASSEMBLY REPLACEMENT.
Failure to do so may result in an electrical shock that
could severely injure you.
Appliance Features
Adjustable Temperature Control: Please see “how
to Operate Your Refrigerated Beverage Center” on
page two.
This product uses one, 6 watt light tube to illuminate
the interior of the beverage center. The light tube is a
very reliable electrical component, but should it not
function properly, please call the dealer you pur-
chased your beverage center from for a replacement
light tube housing assembly. Use only an original
equipment light tube housing assembly from your
dealer or manufacturer.
Interior Light and Switch: The interior light makes it
easy to view the contents of your beverage center.
When the switch is in the
“OFF” position, the light
will come on when the
door is opened. When
the switch is pushed such
5
Using a /16” hex-head driver, remove the two hex-
head screws holding the old light tube housing
assembly in place. Disconnect the electrical plug
from the cabinet’s electrical receptacle and discard
the old light tube housing assembly. Reconnect the
electrical plug of the new light tube housing assem-
bly to the cabinet’s electrical receptacle. Make sure
it is secure and fully inserted.
that the “red” portion of
the rocker is showing, the
switch is in the “on” position and the interior light will
stay on continuously. Remember to turn the off the light
when it is no longer needed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Roll-out Shelves: The roll-out shelves may be pulled
out approximately 14 inches to facilitate product loading
and retrieval. Do not lean on or press down heavily on
the shelves, doing so may damage the shelves or their
content. Pull out shelves gently to minimize any possible
item shifting. To maintain stability, avoid pulling out more
than one shelf at any time.
Before Calling for Service
Before calling for service, check the trouble shooting
table on this page. This table lists possible problems
that you can remedy without difficulty to avoid an unnec-
essary service call.
If you do need service, contact your dealer or the manu-
facturer. In any correspondence, refer to the model
number and serial number of your unit which is located
on the lower front cabinet flange. Retain you proof of
purchase. You may want to record these numbers in the
space provided on this page. Follow the procedure out-
lined on page 5.
The roll-out shelves are equipped with a removable
center section that allows you to customize the stor-
age capability of your beverage center. Your unit is
shipped with two glass shelves,one wine rack, one
wooden bottle cradle, and one fixed wire shelf. For
added versatility, additional center sections are avail-
able. Please contact dealer or see Marvel’s website at
Possible
Causes/Solutions
Problem
•Interior needs cleaning
Odor in cabinet
Noisy operation
•Cabinet not level
•Weak floor
•Cabinet not level
•Weak floor
Cabinet vibrates
•Tube burned out
•No power at outlet
Cabinet light not working
Appliance will not run
•Temperature control turned
to “OFF”
•Line cord not plugged in
•No power at electrical outlet
•House fuse blown
•Prolonged door openings
•Control set too cold
•Condenser needs cleaning
Appliance runs too long
Moisture collects inside
Single Bottle Racks: Because bottles are not stacked
on top of each other, you can easily view and access
your inventory without disturbing other bottles.
•Too many door openings
•Prolonged door openings
•Hot, humid weather
increases condensation
•Hot, humid weather
increases condensation. As
humidity decreases,
Moisture collects on outside
surface
moisture will disappear.
•Control improperly set.
•Control improperly set
•Faulty thermometer
•Relocate thermometer to
center of cabinet and
recheck
Interior too hot/too cold
4
Download from Www.Somanuals.com. All Manuals Search And Download.
If You Do Need Service
How to Obtain Service
In the event that you do need service, be sure to report the
model number, serial number and proof of purchase to your
service representative. Model number and serial number
are found on the serial plate which is located on the lower
front cabinet flange. For your convenience you may want to
record the following information for your records.
Your refrigerated beverage center requires little service
because the best and most up to date materials, equip-
ment and quality methods are employed throughout the
manufacturing process.
If trouble occurs during normal operation, first check the
troubleshooting chart on page 4 to see if any of these
simple steps may correct the problem. If service
becomes necessary:
Date of purchase
Dealer’s Name
Dealer’s Address
Dealer’s City
Contact the dealer where your appliance was purchased
or the manufacturer for the name of your nearest
authorized service representative. The service represen-
tatives will have full authority tom make any repair
deemed necessary.
If you are in an area where there is no service repre-
sentative, write or call the manufacturer directly. We
will make recommendations as to the proper proce-
dure for correction. Service work and replacement -
parts, if required, will be provided as covered by your
limited warranty.
Dealer’s State
Zip
Appliance Serial Number
Model Number
IT IS IMPORTANT THAT YOU SEND IN YOUR WAR-
RANTY RECORD CARD IMMEDIATELY AFTER TAKING
DELIVERY OF YOUR REFRIGERATION APPLIANCE.
Date Warranty Card Sent
(Must be within 10 Days of Purchase)
Every new refrigeration appliance that leaves the factory
contains this Owner's Guide in a safe place for conven-
ient reference.
Normal Responsibilities
of the Owner Include
Under Counter Beverage Center Specifications
Dimensions W x H x D (in.)
Weight
237/
8
x 34 x 241/
4
All freight charges.
145 lbs.
39-69°F
115V
Damage sustained in transit (see page 1)
Mileage charge(s) for service calls.
Proper installation.
Temperature
Power Supply
supplied with a 15 amp plug
Alterations to original equipment.
Removal or installation of additional equipment.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
THE WARRANTIES SET FORTH HEREIN ARE THE
ONLY WARRANTIES EXTENDED BY MARVEL INDUS-
TRIES. ANY IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTY OF MERCHANTABILITY, ARE
LIMITED TO THE DURATION OF THESE EXPRESS
WARRANTIES. IN NO EVENT SHALL MARVEL INDUS-
TRIES BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES OR EXPENSES RESULTING
FROM BREACH OF THESE OR ANY OTHER WAR-
RANTIES, WHETHER EXPRESSED OR IMPLIED.
Some states do not allow the exclusion or limitation of
consequential damages or limitations on how long an
implied warranty lasts, so the above exclusion or limita-
tion may not apply to you. This warranty gives you spe-
cific legal rights, and you may also have other rights
which may vary from state to state.
Marvel Household Refrigeration
Products Limited Warranty
Entire Product - Limited One Year Parts and Labor
Warranty. MARVEL warrants that it will supply all neces-
sary parts and labor to repair or replace in the end
user's home or office, any component which proves to
be defective in materials or workmanship, subject to the
condition and exclusions stated below, for period of one
year from date of purchase by the end user.
Additional Second Through Fifth Year Limited Parts Only
Warranty. During the four years following expiration of
the One Year Limited Warranty, MARVEL will supply
replacement parts for the hermetically sealed refrigera-
tion system which consists of the compressor, condens-
er, drier, connecting tubing and the evaporator that are
proven to be defective due to workmanship or materials
subject to the conditions and exclusions below.
No person, firm or corporation is authorized to make
any other warranty or assume any other obligation for
MARVEL INDUSTRIES. These warranties apply only to
products used in any of the fifty states of the United
States and the District of Columbia.
The above warranties do not cover:
- Shipping costs of replacement parts or returned
defective parts.
- Customer education or instructions on how to use
the refrigerator/freezer.
To obtain performance of this warranty, report any
defects to:
- Any content loss due to product failure. - Removal
or installation.
MARVEL INDUSTRIES
P.O. Box 997
Richmond, Indiana 47375-0997
Phone: 765-962-2521
Nor do the above warranties cover failure of this product
or its components due to:
IN NO EVENT SHALL THE COMPANY BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING, BUT NOT LIMITED TO, CONTENT LOSS.
- Transportation or subsequent damages.
- Use commercially or use other than normal house-
hold or office.
- Improper installation, misuse, abuse, accident or
alteration, use on wiring not confirming to electrical
codes, low voltage, failure to provide necessary
maintenance, or other unreasonable use.
- Parts or service not supplied or designated by MARVEL.
Some states do not allow limitations on length of time
implied warranty may last, so the above limitations may
not apply to you.
This warranty gives you specific legal rights. You may
also have other rights which very from state to state.
The above warranties also do not apply if:
- The original Bill of Sale, deliver date or serial num-
ber cannot be verified.
- Defective parts are not returned for inspection if so
requested by MARVEL.
- The refrigeration equipment is not in the posses-
sion of the original end use purchaser.
Help prevent tragedies
Each year children die because they climb inside a
discarded refrigeration product, get trapped inside
and suffocate. Take precautions to prevent such
tragedies by removing the door, taping or chaining it
shut before discarding.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
W W W . M A R V E L I N D U S T R I E S . C O M
Phone: (765) 962-2521 Fax: (765) 962-2493
Marvel Industries
Part of AGA Foodservice Group
233 Industrial Parkway
P.O. Box 997
Richmond, IN 47375-0997
41008927 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
|