Marshall Electronics
9
Alternate Menu Functions
Menu is shown by holding down ALT and then pressing the
MENU button. (ALT+MENU). Function selection and cursor
movement is performed with the source selection buttons.
1910 East Maple Ave.
El Segundo, CA 90245
Tel.: 800-800-6608 • Fax: 310-333-0688
Email: [email protected]
CH1 - ID Input 5 character
label for each source
CH2 - Date/Time Setup
CH3 - Sequence (Off to30 Second) Changes displayed image at programmed
intervals when SEQN function is selected
CH4 - Miscellany. PIP FORMAT- position and number of PIP windows.
DATE/TIME-CH DISPLAY - Characters are displayed on the screen over video images.
* NOTE: Date/Time and Channel Display overlay is not available in PC ANALOG or S-VIDEO modes
10
Analog PC Menu Functions
V-RD151-4
Users Guide
System Menu in Analog PC Mode
Menu Selected
* Note: When in PC Analog mode to change the source press the SELECT
button with no OSD is displayed on screen
System Display in Pixels and Frequency
Product Overview
Features
1
2
3
4
5
6
7
8
PC Display Position Adjust
Electrical Specifications
Mechanical Specifications
Installation
(Not available in Composite or S-Video mode)
Input Connectors
PC Image Phase and Clock Adjust
(Not available in Composite or S-Video mode)
Switch Settings and Indicators
Primary Menu Functions
Volume adjustment does not function •
Displayed source selection •
MODE adjustment does not function •
System Functions •
PC Input Automatic Configuration
(Auto config requires signal to be present
on VGA connector)
System Reset •
OSD Timeout •
OSD Position •
System Info •
Contrast, Color, Brightness Adjust •
11
Warranty
9
Alternate Menu Functions
Analog PC Menu Functions
Marshall Electronics warranties to the first consumer, that this V-RD151-4 rackmount monitor will, under normal use, be free from defects in workmanship
and materials, when received in its original container, for a period of one year from the purchase date.
10
This warranty is extended to the first consumer only and proof of purchase is necessary to honor the warranty. If there is no proof of purchase provided with
a warranty claim, Marshall Electronics reserves the right, not to honor the warranty set forth above. Therefore, labor and parts may be charged to you.
This warranty does not apply to product exterior and cosmetics. Misuse, abnormal service or handling, improper alterations or modifications in design or con-
struction, voids this warranty. No sales personnel of the seller, nor any other person is authorized to make any warranties other than those described above,
or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time period described above.
System Menu in Analog PC Mode •
PC Display Position Adjust (Not available in Composite or S-Video mode) •
PC Input Automatic Configuration •
Warranty
11
Due to constant effort to improve products and product features, specifications may change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. After inspection, attach adjustable rear support brackets using the supplied thumbscrews and install the
V-RD151-4 in your desired location of a standard EIA 19-inch equipment rack. Adequate ventilation is
required when installed to prevent possible damage to the internal components.
Thumbscrews and
rear support bracket
Attached bracket
4. Connect required cables for signal input and output.
Note: All BNC connectors should be rated for 75Ω.
Note: Power must be applied to the V-RD151-4 to activate loop through video connections
5. Plug the V-PS12-5V1 power supply into the A.C. source.
6. Attach the twist lock Conxal power connection from V-PS12-5V1 power supply to the back of the drawer.
7. Completely Slide the V-RD151-4 out from the drawer and tilt to your desired viewing angle.
8. Turn on the V-RD151-4 by depressing the power switch located on the front of the unit.
6
Input Connectors
VGA IN
HD-15
(FEMALE)
S-Video IN
4 Pin Din
(Female)
Pin1 - GND
Pin2 - GND
Pin3 – Y in
Pin4 – C in
Pin1-Red IN Pin 9-
Pin2-Grn IN
Pin3-Blu IN
Pin4-
Pin10-
Pin11-
Composite
Video IN 1 to 4
Pin12-
Pin5-
Pin13-
Pin14-HSync
Pin15-VSync
Pin6-Gnd
Pin7-Gnd
Pin8-Gnd
S-Video OUT
4 Pin Din (Female)
Pin1 - GND
Active Composite
Video out 1 to 4
12 VDC from
V-PS12-5V1 power
supply
Left Pin - Pos
Right Pin- Neg
Pin2 - GND
Pin3 – Y in
Pin4 – C in
* All Outputs Require Power to be applied for activation
Marshall Electronics
3
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Switch Settings and Indicators
Drawer close interlock micro-switch places
monitor into standby mode when in stored position
A
B
* NOTE: Digital Process Control is not available in PC ANALOG or S-VIDEO modes
A. Digital Process Controls
(DPC)-not available in PC or S-Video Modes
Quad - 4 channels displayed simultaneously on the screen.
PIP -
Picture in Picture menu selected display of 2 to 4 channels.
Zoom - expands a selected portion of the display
Freeze - of full screen image
SEQN - menu selected channel display for 2 to 4 channels of full screen
image. Sequence switching can be set for 1 to 30 second intervals.
MENU - enables alternate menu
ALT -
shift control for selection of highlighted functions
B. Composite Video Controls
Selection for full frame viewing of composite video channels 1 to 4.
Also used for Cursor controls of alternate menu functions.
Illuminates when channel is selected.
C
C. Primary Menu Controls
Power On/Off selection switch illuminates when monitor is switched on.
8
Primary Menu Functions
Primary menu functions are accessed by pressing the MENU button.
Volume adjustment
does not function
PC Analog - Selects input from the HD15 VGA IN connector.
Image is full screen. No DPC functions
Composite - Selects input of composite video 1 to 4 plus DPC functions
Displayed source selection
S-VHS - Selects input from the
SELECT
Menu Control
S-VIDEO IN connector. Image is
full screen. No DPC functions
Television - does not function on this model
V-RD151-4 USERS GUIDE
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|