R
Model CC4300 User Guide
5 Disc CD Changer
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY
INSTRUCTIONS
READ BEFORE OPERATING EQUIPMENT
This product was designed and manufactured to meet strict
13.Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and
the point where they exit from the product.
quality and safety standards. There are, however, some
installation and operation precautions which you should be
particularly aware of.
1. Read Instructions – All the safety and operating
14.Protective Attachment Plug – The product is equipped
with an attachment plug having overload protection. This is
a safety feature. See Instruction Manual for replacement or
resetting of protective device. If replacement of the plug is
required, be sure the service technician has used a
replacement plug specified by the manufacturer that has
the same overload protection as the original plug.
instructions should be read before the product is operated.
2. Retain Instructions – The safety and operating
instructions should be retained for future reference.
3. Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
4. Follow Instructions – All operating and use instructions
15.Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the
antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements for
the grounding electrode. See Figure 1.
should be followed.
5. Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
6. Attachments – Do not use attachments not recommended
by the product manufacturer as they may cause hazards.
7. Water and Moisture – Do not use this product near water-
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming pool,
and the like.
8. Accessories – Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or
sold with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
FIGURE 1
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
9. A product and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
product and cart combination to overturn.
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
10.Ventilation – Slots and openings in the cabinet are
provided for ventilation and to ensure reliable operation of
the product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
ANTENNA
DISCHARGE
UNIT(NEC
SECTION 810-20)
ELECTRIC SERVICE
EQUIPMENT
GROUNDING
CONDUCTORS
(NEC SECTION
810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM (NEC
ART 250, PART H)
11.Power Sources – This product should be operated only
from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to your
home, consult your product dealer or local power company.
For products intended to operate from battery power, or
other sources, refer to the operating instructions.
NEC - NATIONAL ELECTRICAL CODE
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la Classe B est
conforme à la norme NMB-003 du Canada.
12.Grounding or Polarization – This product may be
equipped with a polarized alternating-current line plug (a
plug having one blade wider than the other). This plug will
fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.
Download from Www.Somanuals.com. All Manuals Search And Download.
16.Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
17.Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
18.Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
19.Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any
kind on the product.
20.Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
21.Damage Requiring Service – Unplug this product from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a.When the power-supply cord or plug is damaged.
b.If liquid has been spilled, or objects have fallen into the
product.
c.If the product has been exposed to rain or water.
d.If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation.
e.If the product has been dropped or damaged in any way,
and
f. When the product exhibits a distinct change in performance
– this indicates a need for service.
22.Replacement Parts – When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
23.Safety Check – Upon completion of any service or repairs
to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
24.Wall or Ceiling Mounting – The product should be
mounted to a wall or ceiling only as recommended by the
manufacturer.
25.Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
General Information ..................................................................................................................2
Unpacking...............................................................................................................................................................2
For Your Safety.......................................................................................................................................................2
Compact Discs........................................................................................................................................................3
Placement...............................................................................................................................................................3
Functional Overview .................................................................................................................4
Front Panel Controls...............................................................................................................................................4
Rear Panel Controls................................................................................................................................................6
Remote Control Unit (RC4300CC)..........................................................................................................................7
Connections...............................................................................................................................9
Connecting other Audio Equipment ........................................................................................................................9
Connecting the Remote Control............................................................................................................................10
Operations ...............................................................................................................................11
Playing CDs ..........................................................................................................................................................11
Changing Discs during Play..................................................................................................................................12
Skip and Search Play............................................................................................................................................12
Playing Tracks in Random Sequence (Random Play)..........................................................................................13
Playing the First 10 Seconds of Each Track (Introscan Play)...............................................................................13
Repeat Play ..........................................................................................................................................................14
Playing Tracks in Any Sequence (Programmed Play)..........................................................................................14
Editing for Recording ............................................................................................................................................18
Deleted Play..........................................................................................................................................................22
Selecting a Brightness of the Display ...................................................................................................................24
Selecting a Time Display ......................................................................................................................................25
Using the Headphones .........................................................................................................................................25
External Control (Serial Interface) RS232C..........................................................................................................26
Troubleshooting ......................................................................................................................28
Specifications ..........................................................................................................................29
1
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
Unpacking
Compact Discs
First check the contents of the packaging. It should
contain the following:
The glossy side shining like a rainbow is the front side
of the disc, and the side on which the label is printed
is the back.
- CD-Player CC4300
- Remote control unit (RC4300CC)
- Batteries (AA size) x 2
- Audio cable (1 - with red and white plugs)
- Remote control cable (with orange plugs)
- Instructions
Unlike conventional turntables for playing analog discs,
the CC4300 reads the information recorded on the disc
from underneath without contacting it using a beam of
laser light. Therefore, the performance of a compact
disc will not degrade like conventional analog records.
- Guarantee
Handle discs carefully so as not to damage or
scratch the front side.
If one of these components is missing, please inform
your supplier immediately. Save the packaging material
it may come in handy if you move the appliance.
To protect the disc, avoid placing it in the following
locations:
• In direct sunlight or near a source of heat like a
heater.
• In a place which is damp or dirty.
• In a place which could be exposed to rain, such as
near a window.
For Your Safety
Units shipped to the U.S.A. and Canada are designed
for operation on 120 V AC only.
Safety precaution with use of a polarized AC plug.
However, some products may be supplied with a
nonpolarized plug.
Always keep the disc surface clean.
Up to six billion data units are recorded on the front side
of the disc. When cleaning the disc surface, always be
sure to use a special compact disc cleaner and wipe as
shown below.
CAUTION :
To prevent electric shock, match wide blade of plug to
wide slot, fully insert.
• Do not use conventional record cleaner for analog
records, as this will adversely affect the disc surface.
Store discs properly by placing them in their disc
cases.
• Do not attach a piece of paper or sticker on the
label side of disc. When a disc has a piece of
plastic tape or rental CD label with paste protruded
from the edge or when a disc has a trace of such a
sticky object, do not attempt to play the disc. If such
a disc is played on the CD player, impossibility of
taking out the disc or other malfunction may result.
• Write only on the printed side of a CD-R or CD-
RW, and only with a soft felt-tipped pen.
• Do not use a disc with a special shape.
Do not attempt to play a disc with a special shape
such as a heart-shaped disc or octagonal disc.
Otherwise the equipment malfunction may result.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information
❖ Playing CD-RW discs
This unit can play back the CD-RW (ReWritable) discs
as well as ordinary music CD and CD-R (Recordable)
discs.
Placement
• The CD-R and CD-RW discs should contain
properly-recorded TOC information so that they
can be played back. With the CD recorder system,
writing the TOC information in a disc is referred to
as finalizing the disc. A disc cannot be recognized
as a CD disc and played back unless it has been
finalized properly. For details, please read the
instruction manual provided with a CD recorder.
• TOC stands for Table Of Contents and contains
information such as the total number of tracks and
total playing time of the disc.
• This unit can play only the discs recorded in the
CD-DA format designed for music reproduction.
Do not attempt to play a disc containing other data,
such as a CD-ROM for PCs, on this unit.
• As the playback of a CD-RW disc necessitates
partial change of the player setup, it may take
longer time for reading the TOC information than
when a music CD or CD-R disc is played.
• Place the CD player on a firm, flat surface.
• Keep away from domestic heating equipment and
direct sunlight.
• In a cabinet, allow about 2 inches of free space all
around the player for adequate ventilation.
• If the CD player cannot read CDs correctly, use a
commonly-available cleaning CD to clean the lens
before taking the CD-player to be repaired. Other
cleaning methods may destroy the lens. Always
keep the tray closed to avoid dust on the lens.
• When it is moved from a cold to a warm environment,
allow the CD player to acclimatize for at least 2 hours
in order to avoid damage. When suddenly placed in
a warm environment, the lens may cloud over.
Playing an CD will not be possible then. Wait until
the moisture evaporates.
• A few CD-RW discs may not be played in some
reason. Please use another disc to play.
• Do not use the CD player under extremely damp
conditions.
• Do not expose discs to direct sunlight, high
humidity or high temperature for a long time.
Attention!
If the appliance is not used or operated in
accordance with the instructions, this may result
in exposure to dangerous radiation or other risks.
Only authorized technicians are allowed to open
the appliance casing or to perform repairs or
maintenance.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Functional Overview
Front Panel Controls
1
2
3
4
5
6
OPEN/CLOSE
5DISC CD CHANGER CC4300
1
2
3
4
5
DISC SKIP
D I S C
CHANGER
STANDBY
EDIT
T.SIZE
TIME
RANDOM
REPEAT
POWER ON/STANDBY
PHONES
LEVEL
PROG AUTO
DELETE EDIT
RANDOM REPEAT ALL
A< >B
1
DISCS
INTRO
1
4
7
2
5
8
3
6
9
/
SCENE TRACK
INDEX STEP
A
B
10 11 12
13 14
PROGRAM
DELETE
INTRO
1
2
3
4
5
7
9
11
13
14
16
18
20
8
10
12
15
17
19
21
q
!
POWER ON/STANDBY button
DELETE button
Press this switch to turn the power on and press again to
turn to stand by.
Press this button to delete the undesired tracks, discs or
review the deleted selections.
w
e
r
t
!
!
STANDBY indicator
Lights up red when the CD player is in Stand-by mode.
INTRO (Introscan) button
Press this button to play the first 10 seconds of each track
on CDs.
Disc tray
Load a compact disc on the disc tray.
TIME button
Press this button to display the elapsed or remaining
playing time of the current track or remaining playing time
of the disc.
Disc selector buttons
Use these buttons to select the disc to be played.
!
!
Fluorescent display
For details, refer to the next page.
DISC SKIP button
For loading or unloading discs, press this button to rotate
clockwise to the next disc position.
RANDOM button
Press this button to play tracks on CDs in random
sequence.
y
u
OPEN/CLOSE button (/)
Press this button to open or close the disc tray.
!
!
!
REPEAT button
Press this button to play a track, a disc or all discs
repeatedly.
EDIT button
Press this button to edit the tracks to be recorded onto the
tape.
9 (Stop/Clear) button
Press this button to stop play, clear the programmed
selections or recover the deleted selections.
i
o
PROGRAM button
Press this button to program your favorite tracks, disc or
review the programmed selections.
T. SIZE (Tape size) button
Use this button to select the tape length in edit recording.
∞ (Backward skip/Search) button
• Press this button to replay from the beginning of the
current track or return to a previous track.
• Press and hold down this button to search for a specific
passage in fast backward.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Functional Overview
!
!
§ (Forward skip/Search) button
• Press this button to play from the beginning of a next
track.
• Press and hold down this button to search for a specific
passage in fast forward.
2 / ; (Play/Pause) button
• Press this button to start playing in the stop or pause
mode.
• Press this button to interrupt play temporarily and press
again to restart play.
@
@
PHONES jack
Stereo headphones can be plugged into this jack for private
listening.
LEVEL knob
Turning the control clockwise increases the headphone
level. Turning the control counterclockwise decreases the
headphone level.
❖ Fluorescent Display
A
B
C
D
E
F
G
PROG AUTO
DELETE EDIT
RANDOM REPEAT ALL 1 DISCS
INTRO
INDEX STEP
1
4
7
2 3
5 6
8 9
.
A< >B
SCENE TRACK
A
B
10 11 12
13 14
:
1
2
3
4
5
I
J
K
L
M
H
A
B
C
D
E
H
Disc number display
DELETE indicator
PROGRAM indicator
EDIT display
PLAY indicator
I
J
K
L
M
PAUSE indicator
Track number and Time display
.
REPEAT A< >B indicator
RANDOM PLAY indicator
REPEAT indicator
INTROSCAN indicator
Music calendar display
F
G
Indicators for Repeat, Introscan and
Random play mode
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Functional Overview
Rear Panel Controls
1
2
RS232C
REMOTE
CONTROL
SELECTOR
DIGITAL OUT
COAX. OPTICAL
ANALOG OUT
REMOTE CONTROL
IN
L
EXT. INT.
R
OUT
4
5
6
3
7
z
x
b
n
ANALOG output jacks
Connect these jacks to the CD(or AUX) input jacks of your
amplifier or receiver.
DIGITAL output (COAX.) jack
• Connect this jack to the COAXIAL DIGITAL input jack of
amplifier or receiver to enjoy live digital sound.
• You can record digital sound by connecting the COAXIAL
DIGITAL INPUT jack of MD deck or CD recorder to this
jack.
RS232C
The RS232C port is to be used in conjunction with an
external controller to control the operation of the CD
player by using an external device. (See also page 26.)
DIGITAL output (OPTICAL) jack
• Connect this jack to the OPTICAL DIGITAL input jack of
amplifier or receiver to enjoy live digital sound.
• You can record digital sound by connecting the OPTICAL
DIGITAL INPUT jack of MD deck or CD recorder to this
jack.
• Not all of the commercially-available optical fiber cords
can be used for audio equipment.
If there is an optical fiber cord which cannot be
connected to your audio equipments, consult your
dealer or nearest service organization.
c
REMOTE CONTROL IN/OUT jacks
By connecting this CD player to another Marantz audio
component using a D-BUS remote control cable, you can
operate the components remotely as a single system.
• When connecting to a component with a remote sensor,
connect the REMOTE CONTROL IN jack of this unit to
the REMOTE CONTROL OUT jack of the component
with the remote sensor.
• When connecting to a component which is not equipped
with a remote sensor, connect the component to the
REMOTE CONTROL OUT jack of this unit.
For the D-BUS cable connection, use supplied remote
control cable or a commercially available RCA-type pin
lead.
m
AC input cord
Plug this cord into a wall AC outlet or the switched AC
outlet of amplifier or receiver.
• By connecting this CD player to a Marantz auto reverse
cassette deck (such as the SD4050), automatic
recording from the CD player to the cassette deck can
be carried out.
v
REMOTE CONTROL SELECTOR switch
When using this unit independently, set this switch to
INTERNAL. When using this unit in a system incorporating
a Marantz other equipments with a remote sensor, set the
switch to EXTERNAL.
Note :
• Always set this switch to INTERNAL unless the unit is
connected with other MARANTZ equipment through
a system connection. When this switch is set to
EXTERNAL, the main unit cannot be controlled from
the provided remote control unit.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Functional Overview
o 6 (Search) button
Remote Control Unit (RC4300CC)
Press and hold down this button to search for a specific
passage in fast forward.
! TIME button
1
DISC
POWER
REPEAT
A-B
Press this button to display the elapsed or remaining
playing time of the current track or remaining playing time
of the disc.
12
2
4
1
4
2
5
8
0
3
6
3
13
14
RANDOM
INTRO
! DIMMER button
7
9
5
7
9
Press this button to change the brightness of the display.
PROGRAM
DELETE
15
17
6
8
! DISC button
16
18
When selecting a disc with this button, press this first and
then the desired disc number(1~5) on the numeric
buttons within 2 seconds.
EDIT
T.SIZE
DIMMER
TIME
19
10
REMOTE CONTROL UNIT RC4300CC
! NUMERIC buttons
20
11
Press the corresponding button when selecting tracks or
discs for play, programming or deleting, then the selected
track is played, programmed or deleted directly without use
of the PLAY, PROGRAM/REVIEW or DELETE/REVIEW
button.
• When selecting a two digit number, the second digit
should be pressed within 2 seconds after the first digit
has been pressed
! PROGRAM button
Press this button to program your favorite tracks, disc or
review the programmed selections.
q POWER button
! ; (Pause) button
Press this button to turn the power on and press again to
turn to stand by.
Press this button to interrupt play temporarily and press
again to restart play.
w REPEAT button
Press this button to play a track, a disc or all discs
repeatedly.
! 2 (Play) button
Press this button to start play in the stop or pause mode.
.
e A< >B button
! § (Forward skip) button
Press this button to play a specific passage repeatedly.
Press this button to play from the beginning of a next track.
r RANDOM button
! ∞ (Backward skip) button
Press this button to play tracks on CDs in random
sequence.
Press this button to replay from the beginning of the
current track or return to a previous track.
t INTRO (Introscan) button
! EDIT button
Press this button to play the first 10 seconds of each track
on CDs.
Press this button to edit the tracks to be recorded onto
the tape.
y DELETE button
@ T. SIZE (Tape size) button
Press this button to delete the undesired tracks, discs or
review the deleted selections.
Use this button to select the tape length in edit recording.
u 9 (Stop/Clear) button
Press this button to stop play, clear the programmed
selections or recover the deleted selections.
i 5 (Search) button
Press and hold down this button to search for a specific
passage in fast backward.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Functional Overview
2. Loading batteries
❖ Operation of Remote Control Unit
The life of the batteries used with the remote control
unit is about 6 months with normal use. Also be sure
to replace batteries earlier when you notice that they
are getting weak.
1. Remote control
The distance between the transmitter of the remote
control unit and the IR SENSOR of the CC4300
should be less than about 5 meters. If the transmitter
is pointed to a direction other than the IR SENSOR or
if there is an obstacle between them, remote control
may not be possible.
1. Remove the back cover.
Remote-controllable range
CC4300
Approx 5 meters
Note :
60
• Remove the batteries when they are not used for a
long time.
• Do not use the rechargeable batteries(Ni-Cd type).
°
RC4300CC
2. Insert the new batteries (AA size) with correct (+)
and (–) polarity.
3. Close until it clicks.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Precautions concerning connections :
• Do not plug the AC input cord into the AC outlet when plugging and unplugging connection cords.
• Be sure to connect the white plugs to the L(Left) and the red plugs to the R(Right) jacks when making
connections with the supplied cords.
• Plug the optical digital cable in securely, as far as it will go.
• Refer to the connecting diagram in the operating instructions of AMPLIFIER/RECEIVER.
Connecting other Audio Equipment
CC4300
RS232C
REMOTE
CONTROL
SELECTOR
DIGITAL OUT
COAX. OPTICAL
ANALOG OUT
REMOTE CONTROL
IN
L
EXT. INT.
R
OUT
R
L
L
R
R
L
DIGITAL
INPUT
COAXIAL
DIGITAL
INPUT
OPTICAL
AUDIO
IN
RS232C
External Controller
Amplifier / Receiver
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting the Remote Control
CC4300
RS232C
REMOTE
CONTROL
SELECTOR
DIGITAL OUT
COAX. OPTICAL
ANALOG OUT
REMOTE CONTROL
IN
L
EXT. INT.
R
OUT
EXT. INT.
OUT
IN
REMOTE
CONTROL
REMOTE
CONTROL
Cassette Deck
Amplifier / Receiver
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Playing CDs
4 To interrupt play temporarily, press Play/Pause
button on the unit again or the Pause button on the
remote control.
1. Press the POWER ON/STANDBY button on the
unit or the POWER button on the remote control to
turn on the power.
7
8
0
9
PROGRAM
DELETE
INTRO
STANDBY
or
POWER ON/STANDBY
DISC
POWER
REPEAT
A-B
EDIT
T.SIZE
DIMMER
TIME
or
1
4
2
5
3
6
• " ; " indicator lights up.
• Press Play/Pause button on the unit again or the
Play button on the remote control to restart play.
• Each time the POWER ON/STANDBY (or POWER )
button is pressed, this unit is turned on or off.
5. Press Stop/Clear button on the unit or the Stop/Clear
button on the remote control to stop play.
2. Press the OPEN/CLOSE button on the unit to open
the disc tray. Load the disc(s) and close the disc
7
8
0
9
PROGRAM
DELETE
INTRO
tray.
OPEN/CLOSE
or
EDIT
T.SIZE
DIMMER
TIME
• " \ " indicator lights up when the number of tracks
is more than 14.
• For loading discs on other trays each, press the
DISC SKIP button on the unit.
- Display in Stop Mode -
• 8cm(3 inches) CDs can be loaded on the inside
circle of the tray, too.
Music calendar
Note
PROG AUTO
RANDOM REPEAT ALL 1 DISCS
1
4
7
2
5
8
3
6
9
.
A< >B
SCENE TRACK
INDEX STEP
INTRO
DELETE EDIT
Do not open or close the tray by force.
Doing so may damage it.
A
B
10 11 12
13 14
1
2
3
4
5
Total tracks
Total playing time
3. Press Play/Pause button on the unit or the Play
button on the remote control to start play.
7
8
0
9
PROGRAM
DELETE
INTRO
or
EDIT
T.SIZE
DIMMER
TIME
• " 2 " indicator lights up.
• The unit plays from the first track on the 1st disc to
the last track on the 5th disc.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Changing Discs during Play
Skip and Search Play
1. Press the OPEN/CLOSE button on the unit to open
❖ Selecting a Disc
the disc tray.
• Press the corresponding Disc selector button on
the unit to start play from the desired disc.
OPEN/CLOSE
• Press DISC button on the remote control first and
then the desired disc number(1~5) on the NUMERIC
buttons within 2 seconds.
(Example) When selecting the disc 3.
DISC
POWER
REPEAT
1
2
3
4
5
2. Change the desired discs.
1
4
7
2
5
8
3
6
9
or
RANDO
• The first track of selected disc will be played.
Disc tray
❖ Searching for a Passage during Play
• During playing the disc q, the discs e and r can
• Press and hold down ∞ / § buttons on the unit or
the 5 / 6 button on the remote control until the
desired passage is reached.
be changed.
• After changing the discs, press the OPEN/CLOSE
button on the unit to close the disc tray.
• When changing the disc w or t, press the DISC
SKIP button on the unit and rotate the disc tray.
or
EDIT
T.SIZE
DIMMER
TIME
REMOTE CONTROL UNIT RC4300CC
❖ Selecting a Track during Play
• Press ∞ / § buttons on the unit or the ∞ / §
button on the remote control momentarily and
repeatedly until the desired track is selected.
or
EDIT
T.SIZE
DIMMER
TIME
REMOTE CONTROL UNIT RC4300CC
• When using the NUMERIC buttons on the remote
control.
(Example)
When selecting “9” :
9
2
2
When selecting “22” :
within 2 sec.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Playing Tracks in Random
Sequence (Random Play)
Playing the First 10 Seconds of
Each Track (Introscan Play)
❖ 1 Disc Random Play
❖ 1 Disc Introscan Play
• Press RANDOM button on the unit or the RANDOM
button on the remote control to play tracks in random
sequence.
• Press INTRO button on the unit or the INTRO button
on the remote control to play the first 10 seconds of
each track.
RANDOM
INTRO
1
4
2
5
8
0
3
6
4
5
8
0
6
A-B
RANDOM
INTRO
7
9
RANDOM
INTRO
PROGRAM
DELETE
7
9
or
or
PROGRAM
DELETE
• “RANDOM” indicator lights up.
• “INTRO” indicator lights up.
• The unit automatically selects and plays tracks on
the current disc in random sequence.
• The unit plays the first 10 seconds of each track
from the current disc to the 5th disc.
❖ All Discs Random Play
❖ All Discs Introscan Play
• In the 1 disc random play mode, press RANDOM
button again.
• In the 1 disc introscan play mode, press INTRO
button again.
• The unit automatically selects a disc among five
discs and a track on that disc in random sequence
and plays it.
• After that track has been played, the unit continues
to select another disc and a track on that disc in
random sequence and plays it.
• The unit plays the first 10 seconds of each first
track from the current disc to the last disc.
• Press INTRO button again to cancel the introscan
play.
• Each time INTRO button is pressed, the introscan
play mode changes as follows:
• Press RANDOM button again to cancel the random
play.
INTRO 1 DISC
INTRO ALL DISCS
OFF
• Each time RANDOM button is pressed, the random
play mode changes as follows:
RANDOM 1 DISC
RANDOM ALL DISCS
OFF
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Repeat Play
Playing Tracks in Any Sequence
(Programmed Play)
❖ Repeating a Single Track during Play
• Press REPEAT button on the unit or the REPEAT
button on the remote control after selecting the
desired track.
Note :
• Up to 32 selections can be programmed to play in any
desired sequence.
• The track number greater than 99 can not be memorized.
REPEAT
DISC
POWER
REPEAT
A-B
❖ Programming the Tracks on the CDs
1
4
2
5
8
3
6
or
1. In the stop mode, enter the program mode. Press
PROGRAM button on the unit or the PROGRAM
button on the remote control.
RANDOM
INTRO
7
9
PROGRAM
DELETE
PROGRAM
RANDOM
7
8
0
9
PROGRAM
DELETE
INTRO
❖ Repeating a Disc during Play
or
• After selecting the desired disc, press REPEAT
button again in the 1 track repeat mode.
EDIT
T.SIZE
DIMMER
TIME
❖ Repeating a All Discs during Play
- Display in Program Mode -
• Press REPEAT button again in the 1disc repeat
mode.
PROG
TRACK
• Each time REPEAT button is pressed, the repeat
mode changes as follows:
1
2
3
4
5
REPEAT 1 REPEAT 1 DISC
OFF REPEAT ALL DISCS
2. Select the desired disc.
Press the corresponding Disc selector button or
DISC SKIP button on the unit.
Press DISC button on the remote control first and
then the desired disc number(1~5) on the NUMERIC
buttons within 2 seconds.
❖ Repeating a Specific Passage during Play
1. At the beginning of the desired passage, press
.
A< >B button on the remote control.
(Example) When selecting the disc 1.
REPEAT
1
4
2
5
8
0
3
6
1
2
DISC SKIP
DISC
POWER
REPEAT
A-B
A-B
1
4
7
2
8
3
6
9
RANDOM
INTRO
or
or
7
9
PROGRAM
DELETE
RANDOM
.
• “REPEAT” indicator lights up and “A< >” indicator
is flickering.
PROG
1
2
3
4
5
2. At the end of the desired passage, press this
button again, then “B” indicator lights up and the
desired passage is played repeatedly.
• If the PROGRAM button is pressed without selecting
a track, the selected disc is programmed as a
selection.
• Press REPEAT button to cancel the repeat play.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
3. Select the desired track.
6. Start the programmed play.
Press ∞ / § buttons on the unit or the ∞ / §
button or the NUMERIC buttons on the remote
control.
Press Play/Pause button on the unit or the Play
button on the remote control.
7
8
0
9
(Example) When selecting the track 4.
PROGRAM
DELETE
INTRO
REPEAT
or
1
4
2
5
0
3
6
A-B
EDIT
T.SIZE
DIMMER
TIME
or
or
RANDOM
INTRO
EDIT
T.SIZE
DIMMER
TIME
7
9
PROGRAM
ELETE
• During the programmed play, when you want
normal play without clearing your programmed
selections, select the desired disc with the Disc
selector or DISC SKIP button or the desired track
on the current disc with the NUMERIC buttons, then
normal play will start from that disc or that track.
REMOTE CONTROL UNIT RC4300CC
PROG
4
TRACK
1
2
3
4
5
• To return to the program mode (meaning “PROG”
lights up in the stop mode), press the PROGRAM
button in the stop mode.
4. Store the selected track in the memory. Press
PROGRAM button on the unit or the PROGRAM
button on the remote control.
❖ Checking the Programmed Selections
PROGRAM
• Each time the PROGRAM button on the unit or the
PROGRAM button on the remote control is pressed
in the program mode (meaning “PROG” lights up in
the stop mode), the programmed selections will
appear in the programmed sequence.
RANDOM
7
8
0
9
PROGRAM
DELETE
INTRO
or
EDIT
T.SIZE
DIMMER
TIME
PROGRAM
RANDOM
7
8
0
9
PROGRAM
DELETE
INTRO
Programmed sequence
or
PROG
4
TRACK
1
2
3
4
5
EDIT
T.SIZE
DIMMER
TIME
Playing time of
the programmed tracks
PROG
4
TRACK
1
2
3
4
5
• Because it is impossible to know the playing time
of each selection from five discs, “--:--” can appear
on the time display.
PROG
4
TRACK
1
2
3
4
5
• When selecting a track with the NUMERIC buttons,
the selected track is stored automatically without
pressing the PROGRAM button.
5. Repeat the above steps 2, 3 and 4 until the desired
program is completed.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
❖ Rectifying Any Wrong Programmed
3. Select the track 7.
Selection
Press ∞ / § buttons on the unit or the ∞ / §
button or the NUMERIC buttons on the remote
control.
(Example)
When the track 3, 5 and 7 of the disc 1 are
programmed and you want to store the track 7 of
the disc 3 instead of the track 5 of the disc 1.
A-B
4
5
8
6
RANDOM
INTRO
7
9
PROGRAM
DELETE
or
or
1. Find the track 5 of the disc 1 in program checking
by press PROGRAM button on the unit or the
PROGRAM button on the remote control.
EDIT
T.SIZE
DIMMER
TIME
REMOTE CONTROL UNIT RC4300CC
PROGRAM
RANDOM
7
8
0
9
PROG
TRACK
PROGRAM
DELETE
INTRO
7
1
2
3
4
5
or
EDIT
T.SIZE
DIMMER
TIME
4. Store the selected track in the memory. Press
PROGRAM button on the unit or the PROGRAM
button on the remote control.
PROG
3
TRACK
5
7
1
PROGRAM
RANDOM
7
8
0
9
PROGRAM
DELETE
INTRO
or
2. Select the disc 3.
Press the Disc selector button or DISC SKIP button
on the unit.
EDIT
T.SIZE
DIMMER
TIME
Press DISC button on the remote control first and
then the disc number 3 on the NUMERIC buttons
within 2 seconds.
PROG
TRACK
7
7
7
1
1
1
2
2
2
3
3
3
4
4
4
5
DISC SKIP
DISC
POWER
REPEAT
2
3
4
PROG
1
4
7
2
5
8
3
6
9
TRACK
or
or
5
RANDOM
PROG
3
TRACK
5
PROG
• When selecting a track with the NUMERIC buttons,
the selected track is stored automatically without
the PROGRAM button.
2
3
4
5
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
- To Clear All Programmed Selections
❖ Clearing the Programmed Selections
• Press Stop/Clear button on the unit or the
Stop/Clear button on the remote control for more
than 4 seconds in the program mode.
- To Clear One by One
• Each time Stop/Clear button on the unit or the
Stop/Clear button on the remote control is pressed
in the program mode, the programmed selections
are cleared one by one in the opposite sequence.
7
8
0
9
PROGRAM
DELETE
INTRO
or
7
8
0
9
PROGRAM
DELETE
INTRO
EDIT
T.SIZE
DIMMER
TIME
or
• Opening the disc tray clears all programmed
selections, too.
EDIT
T.SIZE
DIMMER
TIME
OPEN/CLOSE
- To Delete a Specific Selection
• Find the desired selection in program checking, and
press Stop/Clear button to delete.
1. Press PROGRAM button on the unit or the
PROGRAM button on the remote control until the
track (or disc) to delete appears on the display.
PROGRAM
RANDOM
7
8
0
9
PROGRAM
DELETE
INTRO
or
EDIT
T.SIZE
DIMMER
TIME
2. Press Stop/Clear button on the unit or the
Stop/Clear button on the remote control during the
track (or disc) to delete is displayed.
7
8
0
9
PROGRAM
DELETE
INTRO
or
EDIT
T.SIZE
DIMMER
TIME
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Editing for Recording
AUTO
EDIT
1
4
7
2
5
8
3
6
9
10 11 12
13 14
1
2
3
4
5
Note :
• Up to 30 tracks for auto edit or 32 tracks for manual edit
can be edited according to the tape length.
• It is possible only on the current disc.
• Use Disc selector or DISC SKIP buttons before
entering edit mode.
AUTO
EDIT
1
4
7
2
5
8
3
6
9
10 11 12
13 14
1
2
3
4
5
• You can select the tape length at your option with
the NUMERIC buttons on the remote control.
❖ Setting Up Auto Edit
• By NUMERIC buttons, specify tape length of
single way, although T.SIZE stands for tape length
of both sides.
1. In the stop mode, select the auto edit mode. Press
EDIT button on the unit or the EDIT button on the
remote control.
(Example)
When the tape length of each side is 23 minutes.
EDIT
2
3
0
0
EDIT
T.SIZE
DIMMER
TIME
or
REMOTE T RC4300CC
3. Press the EDIT button on the unit or the EDIT
button on the remote control to automatically edit
the tracks to be recorded.
AUTO
EDIT
1
4
7
2
5
8
3
6
9
10 11 12
13 14
1
2
3
4
5
EDIT
• Each time EDIT button is pressed, the edit mode
EDIT
T.SIZE
DIMMER
TIME
changes as follows:
AUTO EDIT
or
(MANUAL) EDIT
OFF
REMOTE T RC4300CC
2. Select the desired tape length.
Press T.SIZE button on the unit or the T.SIZE button
PROG AUTO
EDIT
1
4
2
5
3
6
on the remote control.
TRACK
A
B
11
1
(Example) When the tape length is 46 minutes.
The edited tracks
on the side A
T.SIZE
PROG AUTO
EDIT
EDIT
T.SIZE
DIMMER
TIME
TRACK
A
B
7
10
8
9
12
1
or
REMOTE CONTROL UN
The edited tracks
on the side B
PROG AUTO
EDIT
1
4
7
2
5
8
3
6
9
TRACK
A
B
10 11 12
1
2
3
4
5
• Each time T.SIZE button is pressed, the tape length
changes as follows:
The auto edit is
completed
C-46
C-54
C-60
C-74
C-90
C120
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
❖ Setting Up Manual Edit
5. Press EDIT button on the unit or the EDIT button
on the remote control to start editing for the side B.
1. In the stop mode, select the manual edit mode.
Press EDIT button twice on the unit or EDIT button
twice on the remote control.
EDIT
EDIT
T.SIZE
DIMMER
TIME
EDIT
or
REMOTE T RC4300CC
EDIT
T.SIZE
DIMMER
TIME
or
REML UIT RC4300CC
PROG
EDIT
TRACK
B
1
2
3
4
5
1
4
7
2
5
8
3
6
9
EDIT
10 11 12
13 14
1
2
3
4
5
6. Do the above step 4 to edit the tracks for the side B.
• If the PLAY button is pressed after editing the
tracks, play starts from the first track of the side A
for recording.
2. Select the tape length as you do in “Making auto
edit” procedure.
• If all tracks of the side A have been played, press
the PLAY button to start play from the first track of
the side B for recording.
3. Press PROGRAM button on the unit or the
PROGRAM button on the remote control to
manually edit the tracks to be recorded.
PROGRAM
RANDOM
7
8
0
9
PROGRAM
DELETE
INTRO
or
EDIT
T.SIZE
DIMMER
TIME
PROG
EDIT
TRACK
A
1
2
3
4
5
4. Edit the tracks for the side A repeating steps 3 and
4 in “Playing Tracks in Any Sequence (Programmed
Play)” procedure on page 15.
PROG
1
4
2
5
3
6
EDIT
TRACK
A
11
1
2
3
4
5
Note :
• During manual edit, if the "-" indicator in the time display
disappears and “ \ ” flickers, it means that the total
time of the edited tracks exceeds the tape length. So
you should edit again.
• When a track with a number greater than 30 is edited,
the time display may show "- -- : --".
• Manual edit is only available on the current disc. If you
press Disc selector or DISC SKIP buttons, the unit
exits from edit mode.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
❖ Checking the Edited Tracks
❖ Start Edit Recording
• In the edit mode, check as you do the programmed
tracks. (refer to “Checking the Programmed
Selections” on page 15)
Before start editing, connect remote control input of
Marantz cassette deck with remote control output of
CC4300 by remote control cable.
PROGRAM
RANDOM
Reverse mode switch may be set to any of one side
(O), both sides (p) and continuous play (∏).
7
8
0
9
PROGRAM
DELETE
INTRO
or
- Synchro recording with Marantz auto reverse
cassette deck (when set to both sides (p) or
continuous play (∏) mode).
EDIT
T.SIZE
DIMMER
TIME
1. After setting up Edit program automatically or
manually, setup the cassette deck to rec pause
state.
❖ Clearing All Edited Tracks
• In the edit mode, press the Stop/Clear button on
the unit or the Stop/Clear button on the remote
control for more than 4 seconds.
2. Press Play/Pause button of the unit to start A side
program. The player sends out signal to start
recording and starts playing A side program after 4
seconds.
7
8
0
9
PROGRAM
DELETE
INTRO
or
EDIT
T.SIZE
DIMMER
TIME
• Opening the disc tray clears all edited tracks, too.
3. After A side program complete, player turns to the
OPEN/CLOSE
pause state at the beginning of B side program.
4. When A side of the tape ends up, cassette deck
inverts its recording direction and set to rec pause
state automatically.
• In the manual edit mode only, you can clear or
rectify the edited tracks as you do in “Rectifying Any
Wrong Programmed Selection” or “Clearing the
Programmed Selections” on page 16 and 17.
5. Press Play/Pause button of the unit manually to
start B side recording. Player sends out signal to
restart recording and starts playing B side program
after 4 seconds.
6. After B side program complete, player stops
playing and clears edit program automatically.
• If the tape ends up before edit program of one side
completes, for example by wrong tape length have
chosen, cassette deck send out signal to player to let
the player cancel the rest of program. Player jumps
to the beginning of B side if it was A side or stop
playing and clear edit program if it was B side.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
- Synchro recording with Marantz one-way cassette
deck, or Marantz auto reverse cassette deck set to
one side (O) mode.
- Recording with Marantz cassette deck without
remote cable connection, and recording with the
cassette deck other than Marantz.
1. After setting up Edit program automatically or
manually, setup the cassette deck to rec pause
state.
1. After setting up Edit program automatically or
manually, start recording of cassette deck first.
2. Press Play/Pause button of the unit to start A side
program. Then player starts playing A side
program after 4 seconds.
2. Press Play/Pause button of the unit to start A side
program. The player sends out signal to start
recording and starts playing A side program after 4
seconds.
3. After A side program complete, player turns to the
3. After A side program complete, player turns to the
pause state at the beginning of B side program.
pause state at the beginning of B side program.
4. When A side of the tape ends up, Reverse cassette
tape or invert recording direction manually and start
recording.
4. When A side of the tape ends up, Reverse cassette
tape or invert recording direction manually and set
to rec pause state.
5. Press Play/Pause button of the unit to start B side
recording. Then player starts playing B side
program after 4 seconds.
5. Press Play/Pause button of the unit manually to
start B side recording. Player sends out signal to
restart recording and starts playing B side program
after 4 seconds.
6. After B side program complete, player stops
6. After B side program complete, player stops
playing and clears edit program automatically.
playing and clears edit program automatically.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Deleted Play
3. Select the undesired track.
Press ∞ / § buttons on the unit or the ∞ / §
button or the NUMERIC buttons on the remote
control.
When there are the undesired discs or tracks, you can
delete up to 32 selections.
(Example) When selecting the track 4.
❖ Deleting the Undesired Discs or Tracks
REPEAT
1
4
2
5
0
3
6
1. In the stop mode, enter the delete mode. Press
DELETE button on the unit or the DELETE button
on the remote control.
A-B
or
or
RANDOM
INTRO
EDIT
T.SIZE
DIMMER
TIME
7
9
PROGRAM
ELETE
REMOTE CONTROL UNIT RC4300CC
DELETE
RANDOM
7
8
0
9
PROGRAM
DELETE
INTRO
1
2
3
6
9
or
4
7
5
8
DELETE
TRACK
10 11 12
13 14
1
1
4
7
2
5
8
3
6
9
4. Delete the selected track. Press DELETE button
on the unit or the DELETE button on the remote
control.
TRACK
DELETE
5
10 11 12
13 14
1
2
3
4
DELETE
RANDOM
7
8
0
9
2. Select the undesired disc.
PROGRAM
DELETE
INTRO
Press the corresponding Disc selector button or
DISC SKIP button on the unit.
or
Press DISC button on the remote control first and
then the desired disc number(1~5) on the NUMERIC
buttons within 2 seconds.
(Example) When selecting the disc 1.
1
7
2
5
8
3
6
9
TRACK
DELETE
10 11 12
13 14
1
1
2
DISC SKIP
DISC
POWER
REPEAT
A-B
1
4
7
2
8
3
6
9
• When selecting a track with the NUMERIC buttons,
the selected track is deleted automatically without
pressing the DELETE button.
or
or
RANDOM
1
2
5
8
3
6
9
4
7
DELETE
10 11 12
13 14
1
• If the DELETE button is pressed without selecting a
track, the selected disc is deleted as a selection.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
5. When deleting other tracks on that disc within 8
seconds after the above step 4, repeat the above
steps 3 and 4 and when deleting the tracks on
other discs, repeat the above steps 2, 3 and 4.
6. Start the deleted play.
Press Play/Pause button on the unit or the Play
button on the remote control.
7
8
0
9
PROGRAM
DELETE
INTRO
or
EDIT
T.SIZE
DIMMER
TIME
❖ Checking the Deleted Selections
• Each time the DELETE button on the unit or the
DELETE button on the remote control is pressed in
the delete mode (meaning “DELETE” lights up in
the stop mode), the deleted selections will appear in
the deleted sequence.
DELETE
RANDOM
7
8
0
9
PROGRAM
DELETE
INTRO
or
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
- To Recover All Deleted Selections
❖ Recovering the Deleted Selections
• Press Stop/Clear button on the unit or the
Stop/Clear button on the remote control for more
than 4 seconds in the delete mode.
- To Recover One by One
• Each time Stop/Clear button on the unit or the
Stop/Clear button on the remote control is pressed
in the delete mode, the deleted selections are
recovered one by one in the opposite sequence.
7
8
0
9
PROGRAM
DELETE
INTRO
or
7
8
0
9
PROGRAM
DELETE
INTRO
EDIT
T.SIZE
DIMMER
TIME
or
• Opening the disc tray recovers all deleted selections,
too.
EDIT
T.SIZE
DIMMER
TIME
OPEN/CLOSE
- To Recover a Specific Selection
• Find the desired track in delete selection checking
and press Stop/Clear button to recover.
1. Press DELETE button on the unit or the DELETE
button on the remote control until the track (or
disc) to recover appears.
Selecting a Brightness of the
Display
DELETE
RANDOM
7
8
0
9
PROGRAM
DELETE
INTRO
or
• Each time DIMMER button on the remote control is
pressed, the brightness of the display changes as
follows;
ON
DIM
2. Press Stop/Clear button on the unit or the
Stop/Clear button on the remote control during the
track (or disc) to recover is displayed.
EDIT
T.SIZE
DIMMER
TIME
REMOTE CONTROL UNIT RC4300CC
7
8
0
9
PROGRAM
DELETE
INTRO
or
EDIT
T.SIZE
DIMMER
TIME
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Selecting a Time Display
Using the Headphones
• Each time TIME button is pressed during play,
time display changes as follows:
• For private listening, insert a plug of the headphone
into “PHONES” jack.
TIME
PHONES
EDIT
T.SIZE
DIMMER
TIME
or
REMOTE CONTROL UNIT RC4300CC
Elapsed playing time
of the current track.
TRACK
INDEX
7
8
9
10 11 12
13 14
1
2
3
4
5
:
Remaining playing
time of the current track
TRACK
INDEX
7
8
9
10 11 12
13 14
:
1
2
3
4
5
Remaining playing
time of the disc
7
8
9
10 11 12
13 14
1
2
3
4
5
:
• During random or programmed play, etc., the
remaining playing time of the disc may show "- -- : --".
• When a track of which number is greater than 30 is
programmed, edited or being played, the time
display may show "- -- : --".
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
❖ Data Packet
External Control (Serial Interface)
RS232C
A packet contains data from 5 to 8 bytes in length. In
serial communication, ASCII code from 00h to 7fh is
used. So the HEX data are converted into ASCII code
and set to the data packet. The data packet includes
CR code (0dh) at the end.
The unit can receive external control signals by
connecting a straight cable on the market to the D-sub 9
pin connector for RS232C external control.
Example 1: CD Play (Code: 20 53)
❖ Pin Assignment of the Connector
[2]
[0]
[5]
[3]
CR code
0dh
5 byte
32h 30h 35h 33h
1
2
3
4
5
6
7
8
9
NC
RX
TX
NC
GND
NC
NC
NC
NC
RS232C
5
1
Example 2: T.SIZE (Code 20 104 08)
[2] [0] [1] [0] [4] [0] [8]
CR code
8 byte
32h 30h 31h 30h 34h 30h 38h 0dh
9
6
The unit can identify following commands on next
page.
❖ RS232C Physical Specification
Cable
Straight-type
Connector
D-Sub 9 pin
(Female type)
Baud rate
Data bits
Parity
9600bps
8 bits
None
1 bit
Stop bit
Flow control
None
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
• Remote Control Unit (RC4300CC) RC-5 Code
The unit can be controlled through its infrared IR sensor on the front panel when it receives remote control
signals that supports RC-5 signals as shown in the table on the following.
These remote control (RC-5) codes can also be used if sent through the RS232C port found on the rear panel
of the unit.
Key No.
1
Function
POWER ON/STANDBY
Code
20 12
ASCII Code
32h 30h 31h 32h 0dh
32h 30h 33h 30h 0dh
32h 30h 30h 31h 0dh
32h 30h 30h 32h 0dh
32h 30h 30h 33h 0dh
32h 30h 30h 34h 0dh
32h 30h 30h 35h 0dh
32h 30h 30h 36h 0dh
32h 30h 30h 37h 0dh
32h 30h 30h 38h 0dh
32h 30h 30h 39h 0dh
32h 30h 30h 30h 0dh
32h 30h 32h 39h 0dh
32h 30h 35h 39h 0dh
32h 30h 32h 38h 0dh
32h 30h 33h 36h 0dh
32h 30h 34h 39h 0dh
32h 30h 34h 33h 0dh
32h 30h 35h 33h 0dh
32h 30h 34h 38h 0dh
32h 30h 35h 34h 0dh
32h 30h 33h 33h 0dh
32h 30h 33h 32h 0dh
32h 30h 35h 30h 0dh
32h 30h 35h 32h 0dh
32h 30h 31h 30h 44h 0dh
32h 30h 31h 30h 44h 30h 38h 0dh
32h 30h 37h 31h 0dh
32h 30h 31h 31h 0dh
2
3
4
5
6
7
8
9
DISC
1
2
3
4
5
6
7
20 30
20 01
20 02
20 03
20 04
20 05
20 06
20 07
20 08
20 09
20 00
20 29
20 59
20 28
20 36
20 49
20 43
20 53
20 48
20 54
20 33
20 32
20 50
20 52
20 104
20 104 08
20 71
20 11
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
8
9
0
REPEAT (1/ALL)
A-B (A<->B)
RANDOM
PROGRAM (PROG/REV)
DELETE (DEL/REV)
INTRO
PLAY 2
PAUSE ;
STOP 9
PREVIOUS (SKIP) ∞
NEXT (SKIP) §
REW (SEARCH) 5
FF (SEARCH) 6
EDIT
T.SIZE
DIMMER (DISPLAY)
TIME
• Acceptable RC-5 Code
These RC-5 codes are not supported by remote control unit (RC4300CC), but they can also be used if sent
through the RS232C port found on the rear panel of the unit.
Key No.
Function
POWER ON
Code
20 12 01
20 12 02
20 55
20 56
20 57
ASCII Code
32h 30h 31h 32h 30h 31h 0dh
32h 30h 31h 32h 30h 32h 0dh
32h 30h 35h 35h 0dh
32h 30h 35h 36h 0dh
32h 30h 35h 37h 0dh
a
b
c
d
e
f
STANDBY
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
20 64
20 65
32h 30h 36h 34h 0dh
32h 30h 36h 35h 0dh
g
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If your unit should not perform as expected, consult the table below to see if the problem can be corrected before
seeking help from your dealer or our service organization.
REMEDY
Problem
No power
Possible Cause
• Connect the cord securely.
• Press the POWER button to ON.
• The AC input cord is disconnected.
• The POWER switch is not pressed
correctly.
• Reload the disc with the printed
side up.
No play
• The disc is loaded upside down.
• Clean the disc.
• Load another disc.
• Dirty disc.
• Defective or deeply scratched disc.
• Make connections correctly.
• Operate the amplifier correctly.
• Press the PLAY or PAUSE button
to cancel the pause mode.
No sound
• Incorrect connections.
• Incorrect operation of the amplifier.
• The " ; " indicator lights up.
• Make connections correctly.
Poor or distorted sound
Sound skips
• The unit is connected to the
PHONO input jacks of the amplifier.
• Poor connections.
• Check the connections and connect
all cords securely.
• Play another disc.
• Place this unit on a stable surface.
• Defective or deeply scratched disc.
• This unit is placed on a surface that
is subject to vibration or physical
shock.
• Try again with a scratch-free disc.
• Try again.
Programming or deleting
does not perform.
• The disc is dirty or badly scratched.
• The programming or deleting
procedure is not correct.
• The number of the programmed
selections is 32.
• Check the number of the programmed
selections.
• Press the OPEN/CLOSE button to
open and close the disc tray or press
the POWER switch to turn the power
off and on.
“Error” is displayed.
• Incorrect operation.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
SYSTEM ........................................................................................................................ Compact Disc Digital Audio
TYPICAL AUDIO PERFORMANCES
Number of channels ................................................................................................................................................ 2
Frequency response ............................................................................................................ 20~20,000 Hz 0.5 dB
Signal to noise ratio, A Wtd. .......................................................................................................................... 105 dB
Dynamic range ................................................................................................................................................ 95 dB
Total harmonic distortion, 1 kHz .................................................................................................................. 0.005 %
Wow and flutter ................................................................................................................... Quartz crystal precision
Audio output level ....................................................................................................................................... 2 V RMS
Digital output
Optical ....................................................................................................................................................... –19 dBm
Coaxial .............................................................................................................................................0.5 Vp-p (75Ω)
OPTICAL READOUT SYSTEM
Laser .................................................................................................................................... Semiconductor AlGaAs
Wavelength ................................................................................................................................................... 780 nm
SIGNAL FORMAT
Sampling Frequency ................................................................................................................................... 44.1 kHz
D/A Conversion ............................................................................................................ 1 bit P.L.M. D/A Conversion
Oversampling ................................................................................................................................................ 8 times
GENERAL
Power supply ...................................................................................................................................AC 120 V, 60 Hz
Power consumption .......................................................................................................................................... 12 W
Dimensions (W x H x D) .................................................... 17-5/16 x 4-7/16 x 15-1/2 inches (440 x 113 x 393 mm)
Weight (NET) .................................................................................................................................. 12.8 lbs (5.8 kg)
Note : Design and specifications are subject to change without notice for improvements.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
COUNTRY
ALGERIE
ARMENIA
AUSTRALIA
AUSTRIA
BAHREIN
BANGLADESH
BELGIUM
BULGARIA
CANADA
CHINA
CYPRUS
CZECH REPUBLIC
DENMARK
DUBAI
COMPANY
Azur 2000
NGYIG Ltd.
ADDRESS
8, Lotissement Ben Hatadi, Alger, Algerie
47 A/75 St. Lalaiants, 375000 Yerevan, Armenia
24 Lionel Road, Mt. Waverley, VIC 3149, Australia
Taborstraße 95 / Ladestraße 1, Gebäude Hangartner, A-1200 Wien, Austria
P.O. Box 237,141, Government Avenue, Manama,Bahrein
1078, Ramjoy Mohanja Lane Asadgonj, Chittagong 4000, Bangladesh
Brusselbaan 278, 9320 Erembodegem, Belgium
Makedonia Blvd. 16, 1606 Sofia, Bulgaria
633 Granite Court, Pickering, Ontario
No.38 Yushan Road, ShiQiao, Pan Yu, Guang Dong, China
P.O. Box 5604, Nicosia, Cyprus
Sokolska 41, 67902 Rajecko, OKR,Blansko, Czech Republic
Dali Allé 1, 9610 Noerager, Denmark
Jamo Australia Pty. Ltd.,
Huber & Prohaska GmbH
Ambassador Stores
Target
Van der Heyden Audio N.V.
Ariescommerce GmbH
Lenbrook Industries Limited
Guang Chang Audio International Co., Ltd.
Empire Hifi systems Ltd.
Audio International
Audio Nord
V.V.& SONS
P.O. Box 105, Dubai, U.A.E.
EGYPT
Solimco
9, El Attibaa St. Doki, Cairo, Egypt
ESTONIA
F.Y.R.O.M.
FINLAND
FRANCE
GERMANY
GREECE
HiFi Club Estonia
T.P. KODI
Audio Nord
Marantz France
Marantz Deutschland
Adamco S.A.
Ehte 4, 90503 Haapsalu, Estonia
ul.Cedomir Kantargiev 21a, Skopje, Former Yugoslavian Republic of Macedonija
Uudenmaankatu 4-6, Helsinki SF-00120, Finland
A division of Marantz Europe B.V., P.O. Box 301, 92 156 Suresnes Cedex, France
Hakenbusch 3, 49078 Osnabrück, Germany
188, Hippocratous Street, 11471 Athens, Greece
HEADQUARTERS EUROPE:
HONG KONG
HUNGARY
ICELAND
INDIA
IRAN
IRELAND
ISRAEL
ITALY
IVORY COAST
JAPAN
KOREA
KUWAIT
Marantz Europe B.V.
Marantz Asia Ltd.
Infovox Ltd.
ID Electronics Ltd.
NOVA Audio Private
Home Co.
Marantz Ireland
Elmor Ltd.
Marantz Italy
Hifivoir
P.O. Box 8744, 5605 LS Eindhoven, The Netherlands
Unit 1706, Metroplaza II, 223 Hing Fong Road, Kwai Fong, N.T., Kowloon, Hong Kong
Terez Krt.31, 1067 Budapest, Hungary
Armula 38, 108 Reykjavik, Iceland
8,Punam Co-op.Society 29/30 Road#5, Union Park MUMBAI 400052, India
5th floor no 878 Philips Building Enghelab ave, P.O. 11365/7844 Tehran, Iran
Clonskeagh, Dublin 14, Ireland
52 Heh Beiyar Street, Kikar Hamedina, Tel Aviv, Israel
Via Casati 23, 20052 Monza (Milano), Italy, Servizio Consumatori 1678-20026, Numero Verde
B.P. 2428, Abidjan 01, Ivory Coast
35-1 Sagami Ohno 7-Chome, Sagamihara-shi, Kanagawa 228-8505, Japan
121-210, 2F Shinhan Bldg., 247-17 Seokyo-dong, Mapo-ku, Seoul, Korea
P.O. Box 8196, Salmiah 22052, Kuwait
Marantz Japan Inc.
Mk Enterprises Ltd.
alAlamiah Electronics Intl.
Ace Ltd.
LATVIA
61, LacPlesa Str., Riga LV 1011, Latvia
LEBANON
LITHUANIA
MALAYSIA
MALTA
AZ Electronics S.A., 1,
Accapella Ltd.
Wo Kee Hong Electronics Sdn. Bhd.
Doneo Co Ltd.
P.O. Box 11 2833, Beirut, Lebanon
Ausros, Vartu G/5, Pasazo SKG., 2001 Vilnius, Lithuania
Suite 8.1, Level 8, Menara Genesis, No. 33, Jalan Sultan Ismail, 50250 Kuala Lumpur, Malaysia
78 The Strand, Sliema SLM07, Malta
MAURITIUS
SKR Electronics Ltd.
P.O. Box 685, Bell Village, Port Louis, Mauritius
MILITARY MARKET EUROPE PASCO GmbH
PO BOX 1280, Sandhausen 69200, Germany
NEW ZEALAND
NORWAY
Wildash Audio Systems
Audio Nord
14 Malvern Road, Mt. Albert, Auckland, New Zealand
Sandkerveien 64, Oslo 0483, Norway
OMAN
POLAND
PORTUGAL
PROFESSIONAL EUROPE
PROFESSIONAL U.S.A.
QATAR
REUNION
ROMANIA
RUSSIA
SAUDI ARABIA
SINGAPORE
SLOVAKIA
SLOVENIA
SOUTH AFRICA
SPAIN
Mustafa & Jawad Trading CO.
Philips Polska Sp. z.o.o.
Corel2
Marantz Professional Products
Marantz Professional Products
Almana & Partners W.W.L.
Vision +
Nova Music Entertainment
Absolute Audio
Adawlia Univ. Electr. Apl
Wo Kee Hong Distribution PTE Ltd.
Bis Audio s.r.o.
P.O. Box 1918, Ruwi, Oman
Al.Jerozolimskie 195b, 02 222 Warszawa, Poland
Comércio de Electrónica Lda., Av. Luís Bívar, No 85 A, 1050 Lisboa, Portugal
Kingsbridge House, Padbury Oaks, 575-583 Bath Road, Longford, Middlesex UB7 0EH, U.K.
Distributed by: Superscope Technologies Inc., 1000 Corporate Blvd. Ste.D, Aurora, Illino
P.O. Box 49, Doha, Qatar
180 Rue du Marechal Leclerc, 97400 Saint Denis, Ile de la Reunion
5, Zagazului Str. Bl.1G,apt.18, sector 1,Bucharest, Romania
7/2, Montazhnaya Street, 107497 Moscow, Russia
P.O. Box 2154, Alkhobar 31952, Saudi Arabia
130 Joo Seng Road, #03-02 Olivine Building, Singapore 368357
Nam. SNP 10, 96001 Zvolem, Slovakia
Smartinska 152, HALA V/3, 61000 Ljubljana, Slovenia
P.O. Box 1614, Alberton, 1450, South Africa
Bofex
Coherent Imports (PTY) Ltd.
Marantz Spain
The listening Room
Audio Nord
Martinez Villergas 2, Apartado 2065, Madrid 28027, Spain
Mezzanine Floor, The Landmark 385, Galle Road, Colombo - 3, Sri Lanka
Almedalsvagen 4, Gotenborg 402-23, Sweden
SRI LANKA
SWEDEN
SWITZERLAND
SYRIA
TAHITI
TAIWAN
THAILAND
TUNESIA
TURKEY
U.K.
U.S.A.
YUGOSLAVIA
WWW.MARANTZ.COM
Sound Company AG
Hamzeh & Partners
Covecolor
Pai-Yuing Co. Ltd.
MRZ Standard Co. Ltd.
Societe EDEVIG
Türk Philips Ticaret A.S.
Marantz Hifi UK Ltd.
Marantz America Inc.
ITM Company
Postfach, 8010 Zürich, Switzerland
Hafez Ibrahim Str. No 117, Damascus Shalan, Syria
Av. Prince Hinoi, Cours de l'union sacré, P.O. Box 2334, Papeete, Tahiti
6th No 148 Sung Kiang Road, Taipei 10429, Taiwan R.O.C.
746-750 Mahachai Road, Wangburapa, Bangkok 10200, Thailand
40, Avenue du Golfe Arabe, El Menzah, 1004, Tunesia
Yukari Dudullu Organize sanayi Bolgesi, 2.Cadde no.28, 81260 Umraniye-Istanbul, Turkey
Kingsbridge House, Padbury Oaks, 575-583 Bath Road, Longford, Middlesex UB7 0EH, U.K.
1100 Maplewood Drive Itasca, IL 60143, U.S.A.
Omladinskih Brigada 86, 11070 Belgrade, Yugoslavia
R
is a registered trademark.
Printed in China
03/2002 MITf 08AW851250
Download from Www.Somanuals.com. All Manuals Search And Download.
|