Marantz Projection Television PV6111W User Manual
®
Model PV6111W User Guide  
HD-Ready Rear Projection Television  
As an ENERGY STAR® Partner, Marantz has determined that this product meets the ENERGY STAR® guidelines for  
energy efficiency. ENERGY STAR is a U.S. registered mark.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
All mentions of “Rear Projection TV” in this OPERATION MANUAL refer to the Marantz HD-Ready Rear Projection  
Television.  
IMPORTANT  
To aid reporting in case of loss or theft, please record the Rear Projection TV  
model and serial numbers in the space provided. The numbers are located at  
the rear of the Rear Projection TV.  
Model No.:  
Serial No.:  
Important Information  
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE  
THIS APPLIANCE TO RAIN OR MOISTURE  
The lightning flash with arrowhead within a  
triangle is intended to tell the user that parts  
inside the product are a risk of electric shock to  
persons.  
CAUTION  
RISK OF  
ELECTRIC SHOCK  
DO NOT OPEN  
CAUTION: TO REDUCE THE RISK OF  
ELECTRIC SHOCK,  
DO NOT REMOVE COVER (OR BACK).  
NO USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE  
PERSONNEL.  
The exclamation point within a triangle is  
intended to tell the user that important operating  
and servicing instructions are in the papers with  
the appliance.  
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE  
SLOT, FULLY INSERT.  
WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly  
approved by the manufacturer could void the user’s authority to operate this equipment.  
Note on the TWIN PICTURE screen and SEARCH screen functions  
The TWIN PICTURE screen and SEARCH screen functions provided in this monitor are intended for private viewing  
only. Use of the above video processing functions for profitmaking purpose or for public viewing (clubs, hotels, etc.)  
without prior authorization from the transmitter and/or owner of the video program(s) may be an infringement of  
existing copyright laws.  
“Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-  
40 of the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the  
cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as  
practical.”  
INFORMATION  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15  
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed  
and used in accordance with the operation manual, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
• Relocate or adjust the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
NOTE: This Rear Projection TV will display television closed captioning, in accordance with paragraph 15.119 of  
the FCC rules.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTICE ON ADVERSE EFFECTS ON THE SCREEN  
When playing TV games or displaying still pictures with your Rear Projection TV, be sure to keep in mind the following  
points:  
Picture Burn Prevention  
• Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and  
other fixed (non-moving) patterns can cause permanent damage to projection television receivers. Such “PATTERN  
BURNS” constitute misuse and are NOT COVERED by your Marantz Factory Warranty.  
• When using TWIN PICTURE/Multi-Picture function, the sub-picture should not be left permanently in one corner of  
the screen or a “PATTERN BURN” may develop over a long period of time.  
Public Viewing of Copyrighted Material  
Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources,  
may require prior authorization from the broadcaster or owner of the video program material.  
IMPORTANT SAFETY INSTRUCTIONS  
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to ensure your  
personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In  
order not to defeat the safeguards incorporated into this equipment, observe the following basic rules for its  
installation, use and servicing. For your own protection and reliable usage of your equipment, please be sure to read  
these “Important Safeguards” carefully before use.  
1. Read Instructions—All the safety and operating instructions should be read before the product is operated.  
2. Retain Instructions—The safety and operating instructions should be retained for future reference.  
3. Heed Warnings—All warnings on the product and in the operating instructions should be adhered to.  
4. Follow Instructions—All operating and use instructions should be followed.  
5. Cleaning—Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol  
cleaners. Use a damp cloth for cleaning.  
6. Attachments—Do not use attachments not recommended by the product manufacturer as they may cause hazards.  
7. Water and Moisture—Do not use this product near water – for example, near a bathtub, wash bowl, kitchen sink,  
or laundry tub; in a wet basement; or near a swimming pool; and the like.  
8. Accessories—Do not place this product on an unstable cart, stand, tripod, bracket or table. The product may fall,  
causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod,  
bracket or table recommended by the manufacturer, or sold with the product. Any mounting of the product should  
follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.  
9. Wall or Ceiling Mounting—The product should be mounted to a wall or ceiling only as recommended by the  
manufacturer.  
10. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces  
may cause the product and cart combination to overturn.  
11. Ventilation—Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the  
product and to protect it from overheating, and these openings must not be blocked or covered. The openings  
should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should  
not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the  
manufacturer’s instructions have been adhered to.  
12. Power Sources—This product should be operated only from the type of power source indicated on the marking  
label. If you are not sure of the type of power supply to your home, consult your product dealer or local power  
company. For products intended to operate from battery power, or other sources, refer to the operating  
instructions.  
13. Grounding or Polarization—This product may be equipped with a polarized alternating-current line plug (a plug  
having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety  
feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug  
should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the  
safety feature of the polarized plug.  
14. Power-Cord Protection—Power-supply cords should be routed so that they are not likely to be  
walked on or pinched by items placed upon or against them, paying particular attention to cords  
at plugs, convenience receptacles, and the point where they exit from the product.  
15. Lightning—For added protection for this product during a lightning storm, or when it is left  
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the  
antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
16. Power Lines—An outside antenna system should not be located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with  
them might be fatal.  
17. Overloading—Do not overload wall outlets, extension cords, or integral convenience receptacles as this can  
result in a risk of fire or electric shock.  
18. Object and Liquid Entry—Never push objects of any kind into this product through openings as they may touch  
dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any  
kind on the product.  
19. Servicing—Do not attempt to service this product yourself as opening or removing covers may expose you to  
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.  
20. Damage Requiring Service—Unplug this product from the wall outlet and refer servicing to qualified service  
personnel under the following conditions:  
a. When the power-supply cord or plug is damaged.  
b. If liquid has been spilled, or objects have fallen into the product.  
c. If the product has been exposed to rain or water.  
d. If the product does not operate normally by following the operating instructions. Adjust only those controls that  
are covered by the operating instructions, as an improper adjustment of other controls may result in damage  
and will often require extensive work by a qualified technician to restore the product to normal operation.  
e. If the product has been dropped or damaged in any way.  
f. When the product exhibits a distinct change in performance—this indicates a need for service.  
21. Replacement Parts—When replacement parts are required, be sure the service technician has used replacement  
parts specified by the manufacturer or with the same characteristics as the original part. Unauthorized  
substitutions may result in fire, electric shock, or other hazards.  
22. Safety Check—Upon completion of any service or repairs to this product, ask the service technician to perform  
safety checks to determine that the product is in proper operating condition.  
23. Heat—The product should be situated away from heat sources such as radiators, heat registers, stoves, or other  
products (including amplifiers) that produce heat.  
24. Outdoor Antenna Grounding—If an outside antenna or cable system is connected to the product, be sure the  
antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static  
charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper  
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size  
of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and  
requirements for the grounding electrode.  
EXAMPLE OF ANTENNA GROUNDING ACCORDING TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70  
ANTENNA LEAD-IN WIRE  
GROUND CLAMP  
ANTENNA DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRIC  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
NEC – NATIONAL ELECTRICAL CODE  
POWER SERVICE GROUNDING ELECTRODE SYSTEM  
(NEC PART 250. PART H)  
S2898A  
25. Do not subject your Monitor to impact of any kind. Be particularly careful not to damage the screen surface.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Features  
• SDTV and HDTV compatible  
SDTV and HDTV broadcasts can be displayed by connecting a commercially available DTV decoder.  
• DUAL TUNER (TWIN PICTURE screen and SEARCH screen function)  
Two TV tuners are provided, making it possible to split the screen vertically in two and display moving images  
simultaneously on them. In addition, the channel search function makes it possible to view other programs on  
the right side of the screen.  
DTV HIGH IMAGE QUALITY  
• HD CONTRAST ENHANCER (30MHz)  
A CRT driver compatible with broadband HD broadcasts is used to minimize black and white bleeding for  
faithful reproduction.  
• HD COLOR PURITY PROCESSOR (30MHz)  
This processor is compatible with broadband HD broadcasts and achieves faithful and vivid color reproduction.  
NTSC HIGH IMAGE QUALITY  
• DDFC (Digital Double Format Converter) - 1080 CIRCUIT  
This circuit first converts conventional broadcasts to 480P and then further converts them to 1080I images for  
reduced flicker and smooth edges.  
• 10-BIT 3D-Y/C CIRCUIT  
The use of high-definition brightness signal processing from 8 bits to 10 bits improves data resolution capability  
by a factor of 4 for a much higher S/N ratio.  
• INTELLIGENT NOISE REDUCTION CIRCUIT  
This circuit detects the image S/N ratio and controls Y coring emphasizing the brightness signal element at the  
optimum level for image reproduction with minimal noise.  
• EVC (Enhanced Video Circuit)  
The use of intelligent gamma and luminance/chrominance transit correction results in optimum picture quality  
suitable for large screens.  
• Dual System Component Input for NTSC/Progressive  
Connection to a DVD player with a component output terminal enables high picture quality, superior to that of  
S-VIDEO terminal connections. Also, the Rear Projection TV has a high-resolution component input (480I,  
480P, 1080I), which functions as an interface for high-quality HDTV and DVD images.  
HIGH SOUND QUALITY  
• 3D Q SOUND (3D VIRTUAL SURROUND)  
New 3D sound processing is used to obtain a sound field with natural expansion and a greater sense of depth.  
Virtual surround is possible with only 2 speakers by connecting a DTV Decoder and DVD (Dolby digital).  
• 4-speaker system  
With the high sound quality, you can enjoy a powerful audio presence during HDTV movie broadcasts.  
OTHERS  
• Universal remote control with light function  
The remote control allows you to easily operate a DTV Decoder as a well as a VCR, DVD player and cable  
box. It also comes with a function to light up the main buttons for use in a dimly-lit room.  
• PICTURE OUT PICTURE  
The two built-in tuners enable you to watch two TV programs at the same time, one in the main picture and  
one as the sub-picture, while a commercial message is on the screen.  
• VARIABLE AUDIO OUTPUT (VAO)  
The VAO offers TV remote control of the volume level from separate audio components.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Supplied Accessories  
Size AA  
Dry Batteries (2 pcs.)  
Infrared Remote Control  
Part Number : RRMCG1704CESA  
Coaxial Cable  
Before Operating Your Rear Projection TV  
Location  
• For normal operation, your Rear Projection TV should be set up in the room where cool, adequate  
ventilation is provided. Do not position the back of the Rear Projection TV in a place where free airflow is  
restricted.  
• Any magnetic force may disturb the color picture. Make sure that magnets, speakers, electric clocks,  
toys using magnets or any other magnetic substance, such as an iron are kept well away from this Rear  
Projection TV.  
Power  
Your Rear Projection TV operates on 120 Volts, 60 Hertz (normal household current in the USA) and has a  
polarized plug. If you are unable to insert the plug fully into the outlet, try reversing the plug. If it does not  
fit, contact an electrician. Do not defeat the safety feature of the polarized plug.  
• If the Rear Projection TV is not used for a long period, unplug the Rear Projection TV from the wall outlet to  
economize power. (If the Rear Projection TV is plugged in, slight current still flows, even with the POWER button in  
the OFF position.)  
Note  
• Lines and other noise may appear in TV broadcast images when an FM tuner or radio is located near the Rear  
Projection TV and radio and TV broadcasts are received at the same time. Should such noise appear, turn off either  
the Rear Projection TV or the radio.  
• If you are listening to AM broadcasts, turn the Rear Projection TV off. AM broadcast signals may not be received  
due to the interference of the Rear Projection TV.  
Convergence  
Your Rear Projection TV may need to be converged after being installed in your home. Please follow the  
simple instructions on page 53.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
BeforeOperatingYourRearProjectionTV (Continued)  
Viewing  
The main feature of the Rear Projection TV is its large viewing screen. To be able to enjoy this large  
screen at its best, test the Rear Projection TV by placing it in various different parts of the room, in which it  
will be set, to find the ideal spot for viewing.  
It is best viewed by sitting directly in front of the Rear Projection TV and about 10 to 18 feet from the  
screen. The brightness decreases as the viewer moves to the left or to the right of the set.  
During the daytime, reflections from light outside may appear on the screen. Drapes or screens can be  
used to reduce the reflection or the Rear Projection TV can be placed in a different part of the room.  
If the Rear Projection TV’s audio output is connected to a Hi-Fi system’s external speakers, the best audio  
performance will be obtained by placing the speakers on each side of the set at an equal distance as well  
as on a height which is equal to that of the screen center. For best stereo separation, first place the  
external speakers at least four feet from each side of the Rear Projection TV, then place the surround  
speakers to the side or behind the viewing area. Due to the differences in room sizes and acoustic  
environments some experimentation regarding speaker placement for best performance will be required.  
Before using the Rear Projection TV, prepare the remote control.  
To use the remote control, insert batteries first.  
1
Open the battery cover.  
Pull up the lid in the direction  
of the arrow.  
2
Load the batteries.  
Load the two “AA” size batteries  
supplied so that the battery poles  
3
Close the battery cover.  
Lower the lid in the direction  
of the arrow.  
and  
are positioned as  
indicated.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Antenna Connections  
• To fully utilize the various features provided, such as the 2-Tuner POP System, UNIVERSAL PLUS, and some connectors for high-quality  
VCR/DVD playback, set up this unit properly by following the procedures below.  
Universal Remote Control  
• The UNIVERSAL REMOTE CONTROL can be compatible with various VCR/DVD player and CATV converter brands by setting the correct  
control code.  
UNIVERSAL PLUS  
• The VCR/DVD input mode is selected by pressing the VCR/DVD player PLAY button on the UNIVERSAL REMOTE CONTROL.  
• To use this UNIVERSAL PLUS function, the settings on page 49 must be set in advance.  
Antennas  
• The antenna requirements for good color Rear Projection TV reception are more important than those for black & white television  
reception. For this reason, a good quality outdoor antenna is strongly recommended.  
Type of connector  
F-type connector  
1. The 75 ohm system generally uses a round cable with an  
F-type connector that can easily be attached to a terminal  
without tools (not supplied). The F-type connector should  
be finger tightened only.  
75-ohm coaxial cable (round)  
300-ohm twin-lead cable (flat)  
2. The 300 ohm system uses a flat “twin-lead” cable that can be  
attached to a 75 ohm terminal through a 300-75 ohm  
ADAPTOR (not supplied).  
• Switching between ANTENNA-A and ANTENNA-B is possible by pressing the ANT-A/B button on the remote control.  
• A good color picture depends on a good TV signal, and so does good multi-channel sound. Ask your dealer for advice on how to  
install your external antenna to receive the best possible signal.  
• If you subscribe to Cable TV or have a central antenna in your building, you may not need an external antenna.  
A-1. Connection with Converter/Descrambler Box and VCR  
Coaxial Cable (Not supplied)  
ANTCABLE 75  
Back of Rear Projection TV  
Coaxial Antenna Cable (Not supplied)  
ANT-A  
2-way  
signal  
splitter  
(Not  
supplied)  
OUT  
IN  
Cable lead-in  
Cable TV converter  
(Not supplied)  
OUT  
ANT-B  
R AUDIO L VIDEO  
MONITOR OUT  
(EXCEPT FOR HD AND  
COMPONENT SIGNALS)  
Coaxial Antenna Cable (Not supplied)  
IN 1  
IN 3  
S-VIDEO  
IN 1  
IN 3  
S-Video Cable (Not supplied)  
COMPONENT  
Y
P
B
PR  
VCR  
IN 4  
IN 5  
or  
OUT  
IN  
S-VIDEO VIDEO AUDIO  
HD INPUT IN 3  
R
L
(USE FOR HDTV SIGNAL ONLY)  
R AUDIO L VIDEO  
VAO  
CENTER IN  
R AUDIO L  
Video Cable (Not supplied)  
Audio Cable (Not supplied)  
• Shown here is the preferred method of connecting a VCR and CATV Converter to your Rear Projection TV if you are in  
an area with good signal reception. This way you can view either TV programs or VCR tapes regardless the position of  
the VCR’s TV/VCR switch and you can enjoy stereo tape playback from a stereo VCR.  
Note  
• If your VCR has an S-VIDEO or S-VHS OUT connector, you can connect it to the S-VIDEO IN 1, IN 2 (on the front of the  
Rear Projection TV) or IN 3 connector on the Rear Projection TV in addition to or instead of using the video cable.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Antenna Connections (Continued)  
A-2. Connection recommendation if your cable TV converter has AUX terminals. (If your cable TV converter  
has both RF OUTPUT and AUX terminals, it is recommended to connect them as shown in example A-1.)  
ANT/CABLE 75  
Back of Rear Projection TV  
ANT-A  
Coaxial Antenna Cables (Not supplied)  
2-way  
signal  
splitter  
OUT  
IN  
(Not  
Coaxial Cable  
(Supplied)  
supplied)  
Cable TV converter (Not supplied)  
VIDEO AUDIO  
R
L
Cable lead-in  
OUT  
ANT-B  
Coaxial Cable  
(Not supplied)  
R AUDIO L VIDEO  
MONITOR OUT  
(EXCEPT FOR HD AND  
COMPONENT SIGNALS)  
IN 1  
IN 3  
S-VIDEO  
VCR  
S-Video Cable  
(Not supplied)  
IN 1  
IN 3  
OUT  
IN  
S-VIDEO VIDEO AUDIO  
R
L
COMPONENT  
Y
P
B
PR  
or  
IN 4  
IN 5  
HD INPUT IN 3  
(USE FOR HDTV SIGNAL ONLY)  
R AUDIO L VIDEO  
VAO  
CENTER IN  
Video Cable (Not supplied)  
Audio Cable (Not supplied)  
R AUDIO L  
B. Connection with Converter/Descrambler Box without VCR  
Coaxial Cable (Not supplied) Coaxial Antenna Cable (Not supplied)  
Back of Rear Projection TV  
2-way  
signal  
splitter  
(Not  
OUT  
IN  
supplied)  
Cable TV converter  
(Not supplied)  
Cable lead-in  
ANT/CABLE 75  
ANT-A  
OUT  
ANT-B  
Coaxial Antenna Cable (Not supplied)  
R AUDIO L VIDEO  
MONITOR OUT  
(EXCEPT FOR HD AND  
COMPONENT SIGNALS)  
IN 1  
IN 3  
S-VIDEO  
IN 1  
IN 3  
COMPONENT  
Y
PB  
PR  
IN 4  
HD INPUT IN 3  
(USE FOR HDTV SIGNAL ONLY)  
IN 5  
R AUDIO L VIDEO  
VAO  
CENTER IN  
R AUDIO L  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Antenna Connections (Continued)  
C. Connection with Antenna Cable and VCR  
(Not supplied)  
ANT/CABLE 75  
Back of Rear Projection TV  
ANT-A  
2-way  
signal  
splitter  
Coaxial Cable  
(Not supplied)  
Antenna or  
Cable lead-in  
Coaxial Cable  
(Supplied)  
OUT  
ANT-B  
Coaxial Antenna  
Cable (Not supplied)  
R AUDIO L VIDEO  
MONITOR OUT  
(EXCEPT FOR HD AND  
COMPONENT SIGNALS)  
S-Video Cable  
(Not supplied)  
IN 1  
IN 3  
VCR  
S-VIDEO  
OUT  
IN  
S-VIDEO VIDEO AUDIO  
R
L
IN 1  
IN 3  
COMPONENT  
Y
P
B
PR  
IN 4  
IN 5  
or  
HD INPUT IN 3  
(USE FOR HDTV SIGNAL ONLY)  
Video Cable  
(Not supplied)  
R AUDIO L VIDEO  
VAO  
CENTER IN  
R AUDIO L  
Audio Cable (Not supplied)  
• Shown here is the preferred method of connecting a VCR to your Rear Projection TV if you are in an area with good  
signal reception. This way you can view either TV programs or VCR tapes regardless of the position of the VCR’s  
TV/VCR switch and you can enjoy stereo tape playback from stereo VCR.  
Note  
• If your VCR has an S-VIDEO or S-VHS OUT connector, you can connect it to the S-VIDEO IN 1, IN 2 or IN 3 connector  
on the Rear Projection TV in addition to or instead of using the video cable.  
• To enable the Commercial Skip function (See page 62), connect your TV OUT and ANT-B connector with the coaxial  
cable (supplied).  
• If your lead cable is a 300 ohm twin-lead cable or UHF/VHF separate cable, use a 300/75 ohm ADAPTOR or  
COMBINER (output side is 75 ohm coaxial) to connect to the Rear Projection TV.  
D. Connection with Converter/Descrambler Box and DVD  
Coaxial Cable (Not supplied)  
ANT/CABLE 75  
Coaxial Antenna Cable (Not supplied)  
ANT-A  
2-way  
signal  
splitter  
(Not  
Back of Rear Projection TV  
supplied)  
OUT  
IN  
Cable lead-in  
Cable TV converter  
(Not supplied)  
OUT  
ANT-B  
R AUDIO L VIDEO  
MONITOR OUT  
(EXCEPT FOR HD AND  
COMPONENT SIGNALS)  
Coaxial Antenna Cable (Not supplied)  
IN 1  
IN 3  
S-VIDEO  
S-Video Cable (Not supplied)  
DVD  
IN 1  
IN 3  
COMPONENT  
Y
P
B
PR  
COMPONENT  
OUT  
VIDEO  
OUT  
S-VIDEO OUT  
VIDEO OUT  
CENTER  
IN 4  
IN 5  
OPTICAL  
DIGITAL OUT  
S-VIDEO  
OUT  
L
AUDIO  
OUT  
HD INPUT IN 3  
(USE FOR HDTV SIGNAL ONLY)  
R
SUB  
WOOFER  
DIGITAL  
OUT  
FRONT SURROUND  
or  
R AUDIO L VIDEO  
VAO  
CENTER IN  
R AUDIO L  
Video Cable (Not supplied)  
Audio Cable (Not supplied)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Antenna Connections (Continued)  
E. Connection with Antenna Cable  
Back of Rear Projection TV  
1. Cable without a CATV Converter  
2. VHF/UHF Combination Antenna  
Cable TV lead-in  
ANT/CABLE 75  
ANT-A  
VHF, UHF or  
VHF/UHF combination  
antenna  
75 ohm coaxial cable (round)  
Home Antenna  
terminal (75 ohm)  
or  
OUT  
ANT-B  
300-75 ohm ADAPTOR  
(Not supplied)  
300 ohm twin-lead (flat)  
Coaxial Cable  
(Not supplied)  
3. Separate VHF/UHF Antenna  
VHF ANTENNA  
Coaxial Cable  
(Supplied)  
UHF ANTENNA  
300 ohm twin-lead  
COMBINER  
(Not supplied)  
300 ohm twin-lead  
IN  
OUT  
or  
75 ohm coaxial cable  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main Unit  
Front control section  
POWER  
Press → On.  
Press again → Off.  
POWER  
POWER  
VIEW  
SENSOR AREA  
FOR REMOTE CONTROL  
To open the cover  
R
E
W
O
P
W
VIE  
R
E
POW  
AUDIO L/R input  
BEHIND THE COVER  
ENTER button  
IN 2  
L-AUDIO-R  
MENU  
ENTER  
(Other terminals are  
located on the rear)  
MENU button  
Press MENU button to  
access the MAIN MENU  
screen  
VOL  
CH  
S-VIDEO input  
VIDEO input  
VIDEO  
S-VIDEO  
VOL (+)/(–) buttons  
(+) Increases sound  
(–) Decreases sound  
CH (up)/(down) buttons  
(
(
) Selects the next higher channel as well as VIDEO INPUT  
) Selects the next lower channel as well as VIDEO INPUT  
• If the Rear Projection TV is not used for a long period or during a blackout, turn OFF the POWER of the main unit to  
prevent the Rear Projection TV from malfunctioning.  
Note  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Remote Control Functions  
This remote control can be used to operate the Rear Projection TV, a VCR, a DTV STB Decoder, a DVD Video  
Player and a Cable TV converter.  
The buttons that can be used differ according to the device connected. Please refer to the next page for details.  
Remote control mode select buttons  
INFRARED TRANSMITTER WINDOW  
Use to switch the remote control unit modes.  
• By selecting one of the three mode select buttons,  
this remote control can be used to adjust common  
functions, such as channel selection, for that device.  
POWER  
Press → On.  
Press again → Off. (Stand-by)  
PERSONAL PREFERENCE buttons  
Used to select any of four preset channels.  
(See page 48 to setup.)  
ENTER button  
•
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
MENU  
Press → Accesses MAIN MENU.  
Press again → Exits MAIN MENU.  
(See page 17.)  
PERSONAL PREFERENCE  
Cursor buttons  
Used to move cursor on menu screen.  
A
B
C
D
CHANNEL UP/DOWN  
(+) Selects the next higher channel.  
(–) Selects the next lower channel.  
VOLUME UP/DOWN  
(+) Increases sound.  
(–) Decreases sound.  
ENTER  
INPUT  
AV MODE  
VOL  
CH  
MENU  
AV MODE  
MUTE  
Press → Switches to external video  
(See page 58.)  
INPUT 1 mode.  
MUTE  
Press again → Switches to external video  
INPUT 2 mode.  
Press 3 times → Switches to external video  
Press → Mutes sound.  
Press again → Restores sound.  
INPUT  
ANT-A/B  
•
CLOSED CAPTION appears when sound is muted.  
INPUT 3 mode.  
Press 4 times → Switches to external video  
INPUT 4 mode.  
Press 5 times → Switches to external video  
DIRECT CHANNEL ACCESS  
Accesses any channel/inputs numbers by the keypad.  
button: DTV Decoder only  
DISPLAY  
ENT. LASHBACK  
INPUT 5 mode.  
Press 6 times → Switches back to the  
original TV mode.  
POP FUNCTION  
You can watch two pictures at the same time. (See  
page 59.)  
ANT-A/B button  
Press to switch between ANTENNA-A and  
ANTENNA-B when you wish to watch TV.  
-CH-  
:
Used to switch the channel for the  
sub-picture of the TWIN PICTURE  
screen.  
INPUT:  
Used to select the source from INPUT  
terminals for the sub-picture of the  
TWIN PICTURE screen.  
DISPLAY  
Press →  
Displays receiving channel for  
four seconds.  
DDFC  
TWIN PICTURE: Splits the screen into two smaller  
equally sized screens, when pressed  
again, enlarges the left screen, and,  
Press again → Displays remaining time of  
SLEEP TIMER and VIEW  
TIMER for four seconds.  
if pressed again, exits the function.  
FLASHBACK  
Returns to previously viewed channel.  
SEARCH:  
SELECT:  
FREEZE:  
Press to select the SEARCH  
screen mode.  
Selects the screen in TWIN  
PICTURE and Search screen modes.  
When this button is pressed with  
the regular screen, will change to the  
TWIN PICTURE screen and the  
picture at the time the button was  
pressed will become the sub-picture,  
displayed as a frozen image.  
The left and right screens are  
interchanged with the TWIN  
PICTURE function.  
ENT.  
Used in some instances where a Cable  
Converter Box requires an “enter”  
command after selecting channels, when  
using the DIRECT ACCESS button. (See  
page 63.)  
Q-SOUND  
Controls the surround settings.  
(See page 29.)  
SWAP:  
CM SKIP:  
Use this function when you want to  
scan other channels during a  
commercial break.  
VIEW MODE  
Select view size. (See page 57.)  
VCR/DVD/DTV CONTROL  
LIGHT  
(See pages 63 ~ 67.)  
When this button is pressed, some buttons on the  
remote control unit will light. The lighting will turn off if no  
operations are performed within about six seconds. This  
button is used for performing operations in dark places.  
DDFC  
Used to select High-quality image.  
(See page 58.)  
• The light button on the Remote Control glows in the dark. To use the glow-in-the-dark display on the remote control, place it  
under a fluorescent light or other lighting.  
• The phosphorescent material contains no radioactive or toxic material, so it is safe to use.  
• The degree of illumination will vary depending on the strength of lighting used.  
Note  
• The degree of illumination will decrease with time and depending on the temperature.  
• The time needed to charge the phosphorescent display will vary depending on the surrounding lighting.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Remote Control Functions (Continued)  
• Buttons which can be used with the Rear Projection TV, VCR, CATV, DVD player and DTV STB.  
DTV  
STB  
TV/VCR  
TV VCR  
CATV/DVD  
CATV DVD  
Name of button  
Operation  
POWER  
Power ON/OFF  
VOLUME-UP  
Vol - UP  
VOLUME-DOWN  
MUTE  
Vol - DOWN  
Muting  
0
1
2
Selects Channel  
3
4
5
6
7
8
9
100/ENT.  
•
CHANNEL-UP  
CHANNEL-DOWN  
DISPLAY  
INPUT  
Displays OSD  
Selects Input 1 to 5 or TV  
MENU  
MENU  
CURSOR ↑  
CURSOR ↓  
CURSOR  
CURSOR  
ENTER  
CURSOR ↑  
CURSOR ↓  
→
←
→
←
CURSOR  
CURSOR  
ENTER  
FLASHBACK  
Returns to previously viewed channel  
PERSONAL PREFERENCE A PERSONAL PREFERENCE A  
PERSONAL PREFERENCE B PERSONAL PREFERENCE B  
PERSONAL PREFERENCE C PERSONAL PREFERENCE C  
PERSONAL PREFERENCE D PERSONAL PREFERENCE D  
ANT A/B  
TWIN PICTURE  
SELECT  
SUB CH-UP  
SUB CH-DOWN  
SUB INPUT  
SEARCH  
FREEZE  
SWAP  
CM SKIP  
AV MODE  
VIEW MODE  
DDFC  
Antenna A/B  
TWIN PICTURE POP OFF  
Selects another screen  
→
→
Selects sub screen channel  
Channel search by 3 small screens  
Sub screen is frozen  
Interchanges between main and sub-screen  
Commercial skip  
Selects picture set mode  
Changes screen image  
Selects 540P/1080I/1080I (AUTO)  
On/Off  
Q-SOUND  
POWER(VCR/DVD)  
REC  
On/Off for VCR or DVD player  
Rec for VCR only  
PLAY  
Play  
REW  
Rewind  
FF  
Fast Forward  
STOP  
Stop  
PAUSE  
Pause  
TITLE  
Displays title screen for DVD only  
Skips one channel/track up for VCR/DVD  
Skips one channel/track down for VCR/DVD  
←
SKIP /VCR-ch up  
→
SKIP /VCR-ch down  
DTV • STB  
TV • VCR  
Selects Remote control mode  
CATV • DVD  
Light button  
Lights buttons on the Remote control  
: Buttons which can be used with the Rear Projection TV functions.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EZ SETUP on First Power On  
When you turn on the Rear Projection TV for the first time, it automatically memorizes the broadcasting  
channels in your area.  
Please perform the following steps before you press the POWER button.  
(1) Insert the batteries into the remote control. (See page 8.)  
(2) Connect the antenna cable to the Rear Projection TV. (See pages 9 ~ 12.)  
(3) Plug in the AC POWER cord to the wall outlet.  
Press the POWER button on the  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
SELECT LANGUAGE  
ENGLISH  
POWER  
POWER  
1
2
ESPANOL  
FRANCAIS  
Rear Projection TV or  
on the  
PERSONAL PREFERENCE  
Remote Control to turn on the  
Rear Projection TV.  
• The SELECT LANGUAGE  
screen is displayed.  
SELECT  
ENTER  
EXIT  
A
B
C
D
MENU  
ENTER  
VOL  
CH  
MENU  
AV MODE  
MUTE  
Press  
or  
to select  
SELECT ANTENNA  
ANT-A  
ANT-B  
OSD language from “ENGLISH”,  
“ESPAÑOL” (SPANISH) or  
“FRANCAIS” (FRENCH) and then  
SELECT  
ENTER  
EXIT  
INPUT  
ANT-A/B  
MENU  
ENTER  
press  
.
DISPLAY  
• The SELECT ANTENNA screen  
is displayed.  
ENT. FLASHBACK  
TWIN  
PICTURE  
Q-SOUND  
Press  
or  
to select  
SELECT AIR/CABLE  
AIR  
CABLE STD  
CABLE HRC  
CABLE IRC  
VIEW  
MODE  
CH  
“ANT-A” or “ANT-B” and then  
3
4
INPUT  
TITLE  
FF  
ENTER  
press  
.
SELECT  
ENTER  
EXIT  
REW  
MENU  
• The SELECT AIR/CABLE  
screen is displayed.  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
Press  
or  
to select  
“AIR”, “CABLE STD”, “CABLE  
HRC” or “CABLE IRC” and then  
CONNECT ANTENNA OR CABLE  
START EZ SETUP?  
ENTER  
press  
.
ENTER  
MENU  
EXIT  
Note  
• The EZ SETUP screen is  
displayed.  
• For detailed information, see  
page 45.  
• If EZ SETUP does not memorize all  
the channels in your area, please  
refer to page 45 for more information  
on manually memorizing the  
channels using CHANNEL SETUP.  
• It may be difficult to preset channels  
when the broadcasting signals are  
weak, the channel cycle frequency is  
incorrect or frequency jamming  
occurs in the area. Please refer to  
pages 45 ~ 47 for more information  
on manually memorizing the  
ENTER  
Press  
.
• The tuner automatically  
searches for broadcasting and  
cable TV channels. (The CH No.  
automatically increases when a  
station is found.)  
5
PLEASE WAIT  
AUTO PROGRAMMING  
12  
channels using CHANNEL SETUP.  
• If you exit the SELECT LANGUAGE  
mode, during step 1 or 2 of EZ SETUP  
during the “first power on” procedure,  
MENU  
by pressing the  
button, the next  
• Once EZ SETUP is completed, the lowest channel number memorized is  
displayed (e.g. 2 CH).  
time you turn your Rear Projection TV  
on, the SELECT LANGUAGE menu  
appears on the screen.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Functions  
When you master these basic operations, the rest is simple.  
MENU  
Press  
to access MAIN  
TIMER/CLOCK  
VIDEO  
AUDIO  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
MENU screen.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
4
SCREEN  
PARENTCTRL  
CC  
CH SETUP  
SETUP  
SELECT  
NEXT  
EXIT  
PERSONAL PREFERENCE  
A
B
C
D
MENU  
ENTER  
Press  
or  
to move the  
TIMER/CLOCK  
VIDEO  
AUDIO  
SCREEN  
PARENTCTRL  
CC  
CH SETUP  
SETUP  
VOL  
CH  
VIDEO ADJ.  
PRO ADJ.  
VIDEO NR  
OPC  
MENU  
AV MODE  
MUTE  
cursor to the desired function mode.  
•
•
moves the cursor up.  
SELECT  
NEXT  
EXIT  
moves the cursor down.  
MENU  
INPUT  
ANT-A/B  
DISPLAY  
ENTER  
Press  
or  
to access the  
ENT. FLASHBACK  
VIDEO  
VIDEO ADJ.  
PRO ADJ.  
VIDEO NR  
OPC  
PICTURE  
TINT  
desired function mode.  
COLOR  
BRIGHT  
SHARP  
COLOR TEMP.  
RESET  
TWIN  
PICTURE  
Q-SOUND  
SELECT  
NEXT  
BACK  
EXIT  
VIEW  
MODE  
CH  
MENU  
INPUT  
TITLE  
FF  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
MENU  
Press  
to exit.  
VCR/DVD  
POWER  
DDFC  
• You can return to a previous screen by pressing  
displayed on the right side of the MENU SCREEN.  
, when “BACK” is  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Functions (Continued)  
■ MENU SUMMARY  
1. TIMER/CLOCK  
Using the TIMER/CLOCK mode, you can set the current time and the times for automatically switching on  
and off the power of the Rear Projection TV. See pages 19 ~ 23.  
2. VIDEO  
You can adjust the settings of VIDEO ADJ. (PICTURE, TINT, COLOR, BRIGHT, SHARP, COLOR  
TEMP.),PRO ADJ. (VMS, EVC, BLACK, VDE, GAMMA), VIDEO NR and OPC (optical control). See pages  
25 ~ 27.  
3. AUDIO  
You can adjust the AUDIO ADJ. (BASS, TREBLE, BALANCE), Q SOUND, EQUISOUND, internal  
SPEAKER and MTS. See pages 28 ~ 30.  
4. SCREEN  
You can adjust the screen size. See pages 31 ~ 32.  
5. PARENT CTRL (V-CHIP/VIEW TIMER)  
• SECRET No.: You must set the password (SECRET No.) when using parent control functions.  
• V-CHIP: This function allows you to restrict viewing of TV programs, to control TV usage based on FCC  
data and to prevent your children from watching violence or sexual scenes that may be harmful.  
See pages 33 ~ 42.  
• VIEW TIMER: This function allows you to restrict TV viewing time and also to control TV usage. This  
function is for preventing your children from watching too much TV. See pages 43 ~ 44.  
6. CC (CLOSED CAPTION)  
Your Rear Projection TV is equipped with an internal Closed Caption decoder. “Closed Caption” is a  
system which allows you to view conversations, narration, and sound effects in TV programs and home  
videos as subtitles on your TV screen. See page 24.  
7. CH SETUP (CHANNEL SETUP)  
You can set AIR/CABLE, CH SEARCH, CH MEMORY, FAVORITES and UNIV. PLUS. See pages 45 ~ 49.  
• AIR/CABLE: You can set the TV signal mode of AIR,  
CABLE STD, CABLE HRC and CABLE IRC. See page 45.  
• CH SEARCH: You can save broadcast TV channels into memory. See page 46.  
• CH MEMORY: You can add weak or additional channels, or erase unwanted channels from TV memory.  
See page 47.  
• FAVORITES: By selecting the FAVORITES channels in advance you can select your favorite channels  
easily. See page 48.  
• UNIV. PLUS: The VCR/DVD input mode will be selected when VCR/DVD player play starts. See page 49.  
8. SETUP  
You can set LANGUAGE, GRAY SCREEN, ENERGY SAVE, CONVER. ADJ., INPUT MODE, and CH/  
INPUT ID. See pages 50 ~ 56.  
• LANGUAGE: Allows you to select between ENGLISH, SPANISH and FRENCH from the ON SCREEN  
DISPLAY. See page 50.  
• GRAY SCREEN: Automatically turns the screen gray if a broadcast signal is not received. See page 51.  
• ENERGY SAVE: This function controls the BRIGHTNESS level of CRT and reduces power consumption  
about 20 percent. See page 52.  
• CONVER. ADJ.: You can use this mode to align (converge) the three picture beams of red, green and  
blue colors. See pages 53 ~ 54.  
• INPUT MODE: You can select input signal in “Input 3 or 4”. See page 55.  
• CH/INPUT ID: This function can be used to input and display names (up to four letters) for channels and  
terminal inputs. See page 56.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TIMER/CLOCK  
Using the TIMER/CLOCK mode, you can set the current time and the times for automatically switching on  
and off the power of the Rear Projection TV. The TIMER/CLOCK mode features the following three types:  
• CLOCK SET mode...... Sets the current time.  
• SLEEP TIME mode ..... Sets the time for switching off the power.  
• TV-ON TIME mode ..... Sets the time for switching on the power.  
CLOCK SET  
■ SETTING THE TIME MANUALLY  
MENU  
Press  
to access MAIN  
TIMER/CLOCK  
VIDEO  
AUDIO  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
MENU screen.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
4
5
SCREEN  
PARENTCTRL  
CC  
CH SETUP  
SETUP  
SELECT  
NEXT  
EXIT  
PERSONAL PREFERENCE  
A
B
C
D
MENU  
ENTER  
Press  
or  
to access  
ENTER  
TIMER/CLOCK  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
––– REMAIN  
the TIMER/CLOCK mode.  
SELECT  
NEXT  
BACK  
EXIT  
VOL  
CH  
MENU  
AV MODE  
MUTE  
MENU  
INPUT  
ANT-A/B  
Press  
or  
to move the  
TIMER/CLOCK  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
cursor to “CLOCK SET”.  
SELECT  
NEXT  
BACK  
EXIT  
DISPLAY  
ENT. FLASHBACK  
MENU  
TWIN  
PICTURE  
Q-SOUND  
ENTER  
Press  
or  
to access the  
:CLOCK SET  
AUTO CLOCK  
OFF  
VIEW  
MODE  
CH  
ON  
CLOCK SET mode.  
INPUT  
TITLE  
FF  
SELECT  
ENTER  
BACK  
REW  
MENU  
EXIT  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
Use  
or  
to select  
:CLOCK SET  
TIME  
--:----  
ENTER  
“OFF” and then press  
access the current time setting  
screen.  
to  
ADJUST  
SELECT  
BACK  
MENU  
EXIT  
• If “ON” is selected, the time that is being sent from the broadcasting station will  
automatically be set (proceed to steps under “AUTO CLOCK SETTING” on  
page 20).  
Input the current time by using  
:CLOCK SET  
TIME  
10:00AM  
6
,
,
or  
to set.  
then  
ADJUST  
SELECT  
ENTER  
EXIT  
ENTER  
MENU  
press  
Press  
MENU  
to exit.  
7
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TIMER/CLOCK (Continued)  
■ AUTO CLOCK SETTING  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
Use  
or  
to select “ON”  
:CLOCK SET  
XDS CH  
AUTO  
ANT-A  
ANT-B  
ENTER  
and then press  
to display  
PERSONAL PREFERENCE  
5
6
the XDS CH screen.  
A
B
C
D
SELECT  
ENTER  
BACK  
MENU  
EXIT  
ENTER  
Press  
or  
, select  
:CLOCK SET  
XDS CH  
AUTO  
ANT-A  
ANT-B  
VOL  
CH  
MENU  
AV MODE  
MUTE  
“AUTO”, “ANT-A” or “ANT-B” and  
ENTER  
then press  
.
SELECT  
NEXT  
BACK  
EXIT  
MENU  
INPUT  
ANT-A/B  
ANT-A: This function will  
AUTO: XDS CH (This function will  
automatically register the  
time from the extended  
channel).  
automatically register  
the time from the  
DISPLAY  
ENT. FLASHBACK  
channel that is  
connected to ANT-A.  
ANT-B: This function will  
automatically register  
the time from the  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
INPUT  
TITLE  
FF  
channel that is  
REW  
connected to ANT-B.  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
• It is recommended that the “AUTO” function is utilized.  
If you decide to select “ANT-A” or  
ENTER  
“ANT-B”, press  
and then,  
7
8
select the channel number by  
THE CLOCK IS AUTOMATICALLY SET  
WHEN THE UNIT IS TURNED OFF.  
using  
,
, and then  
Note  
press  
.
ENTER  
• The following message will  
appear after having selected the  
AUTO CLOCK function.  
XDS is information provided  
by television programs which  
contains program rating  
data, program Start and End  
times, and Time of Day  
information. This XDS data  
determines whether or not  
parental block settings will  
effect the program or  
Turn the power off.  
• The current time will be  
automatically registered.  
channel being viewed.  
• If you move to another area, set the channels (See page 46 for memorizing the channels) and the clock again  
according to the above procedure.  
• In the event that the AUTO CLOCK has still not been set, even after turning off the power for a few hours, it could  
be that XDS signals are not being broadcast in your area. In this case, the clock should be set manually (See page  
19 for manual clock settings.)  
Note  
• If the antenna signal is weak, the AUTO CLOCK function may not operate properly.  
• The AUTO CLOCK will not function if there is no XDS signal broadcast.  
• Select a channel that carries XDS signals with the  
or  
button.  
“AIR” →  
“CABLE-STD” →  
“CABLE-HRC”, “CABLE-IRC” →  
2
3
4 ……… 68  
69  
2
...  
125  
3 ……… 124  
2
3
4 ……… 124  
2
...  
1
2
125  
2
...  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TIMER/CLOCK (Continued)  
SLEEP TIME  
MENU  
Press  
to access MAIN  
TIMER/CLOCK  
VIDEO  
AUDIO  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
MENU screen.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
4
5
6
SCREEN  
PARENTCTRL  
CC  
CH SETUP  
SETUP  
SELECT  
NEXT  
EXIT  
PERSONAL PREFERENCE  
MENU  
A
B
C
D
ENTER  
Press  
or  
to access  
TIMER/CLOCK  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
ENTER  
––– REMAIN  
the TIMER/CLOCK mode.  
SELECT  
NEXT  
BACK  
EXIT  
VOL  
CH  
MENU  
AV MODE  
MUTE  
MENU  
INPUT  
ANT-A/B  
ENTER  
Press  
or  
to access  
:SLEEP TIME --- REMAIN  
---  
3‰  
6‰  
9‰  
12‰  
the SLEEP TIME mode.  
SELECT  
ENTER  
BACK  
DISPLAY  
MENU  
MENU  
MENU  
EXIT  
ENT. FLASHBACK  
TWIN  
PICTURE  
Q-SOUND  
Press  
or  
to select a  
:SLEEP TIME ---- REMAIN  
---  
3‰  
6‰  
9‰  
VIEW  
MODE  
CH  
sleep time from “30”, “60”, “90” or  
“120” minutes.  
INPUT  
TITLE  
FF  
SELECT  
ENTER  
BACK  
12‰  
REW  
EXIT  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
ENTER  
Press  
to confirm your  
TIMER/CLOCK  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
9‰ REMAIN  
selection.  
SELECT  
NEXT  
BACK  
EXIT  
MENU  
Press  
to exit.  
• To turn off the SLEEP TIME, repeat the above steps and select “– – – REMAIN” during step 4.  
• The amount of time remaining is displayed for four seconds at one-minute intervals for five minutes before the  
power is switched off.  
Note  
• “0 REMAIN” is displayed for 10 seconds before the power is switched off.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TIMER/CLOCK (Continued)  
TV-ON TIME  
This function cannot be used if the current time has not been set. (See page 19.)  
MENU  
Press  
to access MAIN  
TIMER/CLOCK  
VIDEO  
AUDIO  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
MENU screen.  
1
2
3
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
SCREEN  
PARENTCTRL  
CC  
CH SETUP  
SETUP  
SELECT  
NEXT  
EXIT  
PERSONAL PREFERENCE  
MENU  
A
B
C
D
ENTER  
Press  
or  
to access  
TIMER/CLOCK  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
ENTER  
––– REMAIN  
the TIMER/CLOCK mode.  
SELECT  
NEXT  
BACK  
EXIT  
VOL  
CH  
MENU  
AV MODE  
MUTE  
MENU  
Press  
or  
to select  
INPUT  
ANT-A/B  
:TV-ON TIME  
TIME  
--:----  
“TV-ON TIME” and then press  
STATUS  
SELECT  
NEXT  
BACK  
EXIT  
ENTER  
DISPLAY  
or  
to display the  
MENU  
ENT. FLASHBACK  
TV-ON TIME screen.  
TWIN  
PICTURE  
Q-SOUND  
Use  
or  
to select  
VIEW  
MODE  
CH  
:TV-ON TIME  
ENTER  
TIME  
--:----  
“TIME” and then press  
or  
4
5
INPUT  
TITLE  
FF  
ADJUST  
SELECT  
ENTER  
EXIT  
.
REW  
CH/SKIP  
MENU  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
Specify the time when you want the  
Rear Projection TV to turn on by  
:TV-ON TIME  
TIME  
7:00AM  
pressing  
,
,
and  
ADJUST  
SELECT  
ENTER  
EXIT  
ENTER  
MENU  
and then press  
.
Press  
and then press  
to select “STATUS”  
:TV-ON TIME  
STATUS  
OFF  
ENTER  
.
6
ON  
SELECT  
BACK  
EXIT  
MENU  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TIMER/CLOCK (Continued)  
Press  
“ON” or “OFF”.  
or  
to select  
:TV-ON TIME  
STATUS  
OFF  
7
ON  
• ON: Activates the TV-ON  
TIMER.  
• OFF: Deactivates the TV-ON  
TIMER.  
SELECT  
BACK  
EXIT  
MENU  
MENU  
Press  
to exit.  
8
• Be aware that if the time is not set, the TV-ON TIME function cannot be used. Prior  
to accessing the above function, remember to set the current time.  
• When the STATUS of TV-ON TIME is ON, the VIEW TIMER LED will light up.  
• When the STATUS of TV-ON TIME is ON, and a blackout occurs, the VIEW TIMER  
LED will start to blink. (This is to inform that there is the possibility that the TIMER  
is not or was not active during the blackout.)  
Note  
To stop the LED from blinking, reset the current time, and set the STATUS to OFF.  
• Once the TV-ON TIME becomes activated, the STATUS automatically goes back to  
OFF. (The time the TV was set to turn on will not be cleared).  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Closed Caption  
How to set Closed Caption  
• Your Rear Projection TV is equipped with an internal Closed Caption decoder. “Closed Caption” is a  
system which allows you to view conversations, narration, and sound effects in TV programs and home  
videos as subtitles on your Rear Projection TV screen.  
• Not all programs and videos offer closed caption. Please confirm whether the Closed Caption system  
applies to the broadcast program or the video tape you are watching. (The  
compatibility with the Closed Caption system.)  
mark signifies  
• Closed Caption broadcasts can be viewed in two modes: CAPTION and TEXT. For each mode, two  
channels are available, CH1 and CH2.  
• The CAPTION mode displays subtitles for dialogue in TV programs while  
allowing clear view of the picture.  
• The TEXT mode superimposes other information (such as TV program schedules,  
weather forecasts, etc.) that is independent of the TV programs, in the picture.  
MENU  
Press  
to access MAIN  
MENU screen.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
PERSONAL PREFERENCE  
Press  
or  
to move  
TIMER/CLOCK  
VIDEO  
AUDIO  
A
B
C
D
the cursor to “CC” (Closed Caption).  
SCREEN  
PARENTCTRL  
CC  
CH SETUP  
SETUP  
SELECT  
NEXT  
EXIT  
MODE  
DATA  
ENTER  
MENU  
VOL  
CH  
MENU  
AV MODE  
MUTE  
ENTER  
Press  
or  
to access  
CC  
MODE  
DATA  
TEXT  
3
4
the CC (Closed Caption) setting  
mode.  
SELECT  
NEXT  
BACK  
EXIT  
INPUT  
ANT-A/B  
MENU  
DISPLAY  
Press  
or  
to move  
:MODE  
OFF  
CAPTION  
TEXT  
ENT. FLASHBACK  
the “ ” mark to either “MODE”  
or “DATA” (e.g. “MODE”) and then  
SELECT  
BACK  
EXIT  
ENTER  
press  
or  
.
MENU  
Note  
MODE:  
DATA:  
• If a broadcast has Closed Caption  
CAPTION  
CH 2  
OFF  
CH 1  
MUTE  
and  
is pressed, the Rear  
Projection TV enters CAPTION  
TEXT  
MUTE  
mode automatically. Pressing  
again will return the Rear Projection  
TV to its previous condition.  
Press  
or  
to move the  
• Closed Caption may malfunction  
(white blocks, strange characters,  
etc.) if signal conditions are poor or  
if there are problems at the  
broadcast source. This does not  
necessarily indicate a problem with  
your Rear Projection TV.  
• If any button is pressed to call up  
the ON SCREEN DISPLAY while  
viewing a Closed Caption  
broadcast, the closed captions will  
disappear momentarily.  
• When viewing in TEXT mode, if no  
TEXT broadcast is being received,  
for some programs the screen may  
become dark and blank. Should  
this occur, set the Closed Caption  
mode to “OFF”.  
:MODE  
OFF  
CAPTION  
TEXT  
cursor to an item you want to set.  
5
6
SELECT  
BACK  
EXIT  
MENU  
MENU  
Press  
to exit.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Video Adjust  
Description of Adjustment Items  
Selected item  
PICTURE  
TINT  
button  
button  
To decrease contrast  
To make skin tones purplish  
To decrease color intensity  
To decrease brightness  
To decrease sharpness  
To increase contrast  
To make skin tones greenish  
To increase color intensity  
To increase brightness  
To increase sharpness  
COLOR  
BRIGHT  
SHARP  
Allows hue adjustment of the entire screen (Low produces the reddest hue while High produces the bluest  
hue). (LOW-M.L. (Mid Low)-M.H. (Mid High)-HIGH)  
COLOR TEMP.  
RESET  
To return all adjustments to the factory preset levels  
MENU  
Press  
to access MAIN  
TIMER/CLOCK  
VIDEO  
AUDIO  
SCREEN  
PARENTCTRL  
CC  
VIDEO ADJ.  
PRO ADJ.  
VIDEO NR  
OPC  
MENU screen and then use  
1
2
3
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
or  
to select “VIDEO”.  
SELECT  
NEXT  
EXIT  
CH SETUP  
SETUP  
PERSONAL PREFERENCE  
MENU  
A
B
C
D
ENTER  
Press  
or  
to access  
VIDEO  
ENTER  
VIDEO ADJ.  
PRO ADJ.  
VIDEO NR  
OPC  
PICTURE  
TINT  
COLOR  
BRIGHT  
SHARP  
COLOR TEMP.  
RESET  
the VIDEO mode.  
SELECT  
NEXT  
BACK  
EXIT  
VOL  
CH  
MENU  
AV MODE  
MUTE  
MENU  
Press  
“
then  
or  
to move the  
( )  
STD  
:VIDEO ADJ.  
PICTURE  
TINT  
COLOR  
BRIGHT  
SHARP  
COLOR TEMP.  
RESET  
INPUT  
ANT-A/B  
1‰‰  
‰
5‰  
5‰  
5‰  
MH  
” mark to “VIDEO ADJ.” and  
SELECT  
NEXT  
BACK  
EXIT  
DISPLAY  
ENTER  
press  
or  
to access the  
MENU  
ENT. FLASHBACK  
VIDEO ADJ. mode.  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
Press or  
to move the  
(
1‰‰  
‰
)
:VIDEO ADJ.  
PICTURE  
TINT  
STD  
“
” mark to an item (e.g.  
4
5
INPUT  
TITLE  
FF  
COLOR  
BRIGHT  
SHARP  
COLOR TEMP.  
RESET  
5‰  
5‰  
5‰  
MH  
“COLOR”) you want to adjust.  
SELECT  
NEXT  
BACK  
EXIT  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
MENU  
VCR/DVD  
POWER  
DDFC  
ENTER  
Press  
or  
to access  
ADJUST  
BACK  
EXIT  
COLOR (STD)  
5‰  
MENU  
the COLOR adjust mode.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Video Adjust (Continued)  
Press  
or  
to adjust  
ADJUST  
BACK  
EXIT  
COLOR (STD)  
3‰  
6
7
MENU  
ENTER  
“COLOR” and press  
.
MENU  
Press  
to exit.  
• To set other VIDEO  
adjustments, repeat steps 4 to  
6.  
AV MODE  
• Pressing  
changes the setting applied to the currently viewed image in the  
following sequence (See page 59.):  
STD → SOFT → USER → DYNAMIC → STD  
For example, the “SOFT” setting can be used conveniently with the VCR and the  
Note  
“DYNAMIC” setting can be used with the DVD player.  
PRO Adjust  
Description of Adjustment Items  
Selected item  
Adjustment  
Variable value  
VMS (Velocity  
This circuit modifies the frequency or speed of scanning.  
OFF-LOW-MID-HIGH  
Modulation Scanning)  
Switching this on enhances the detail of video and color.  
ON-OFF  
EVC (Enhanced Video  
Circuit)  
Allows adjustment of the degree of dark portions of the picture to change  
the sense of depth.  
BLACK  
ON-OFF  
Allows contour adjustment in the vertical direction.  
ON-OFF  
VDE (Vertical Detail  
Enhancement)  
Allows the dark portions of the picture to be corrected for easier viewing.  
To return all adjustments to the factory preset levels.  
OFF-SOFT-MID-HARD  
GAMMA  
RESET  
MENU  
Press  
to access MAIN  
TIMER/CLOCK  
VIDEO  
AUDIO  
SCREEN  
PARENTCTRL  
CC  
VIDEO ADJ.  
PRO ADJ.  
VIDEO NR  
OPC  
MENU screen and then use  
1
2
3
or  
to select “VIDEO”.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
SELECT  
NEXT  
EXIT  
CH SETUP  
SETUP  
PERSONAL PREFERENCE  
MENU  
A
B
C
D
ENTER  
Press  
or  
to access  
VIDEO  
VIDEO ADJ.  
PRO ADJ.  
VIDEO NR  
OPC  
PICTURE  
TINT  
COLOR  
BRIGHT  
SHARP  
COLOR TEMP.  
RESET  
ENTER  
the VIDEO mode.  
SELECT  
NEXT  
BACK  
EXIT  
VOL  
CH  
MENU  
AV MODE  
MUTE  
MENU  
Press  
“
or  
to move the  
:PRO ADJ. (DYNAMIC)  
VMS  
EVC  
MID  
ON  
” mark to “PRO ADJ.” mode,  
INPUT  
ANT-A/B  
BLACK  
VDE  
ON  
ON  
SELECT  
NEXT  
BACK  
EXIT  
ENTER  
and then press  
or  
to  
GAMMA  
RESET  
MID  
DISPLAY  
MENU  
access the PRO ADJ. mode.  
ENT. FLASHBACK  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Video Adjust (Continued)  
Press  
or  
to move the  
:PRO ADJ. (DYNAMIC)  
EVC  
OFF  
ON  
“
” mark to an item (e.g. “EVC”)  
4
you want to adjust, then press  
SELECT  
BACK  
EXIT  
ENTER  
or  
to access the EVC  
MENU  
mode.  
Press  
or  
to select  
“ON” or “OFF”, and then press  
5
6
ENTER  
.
MENU  
Press  
to exit.  
• To set other PRO adjustments,  
repeat steps 4 to 5.  
VIDEO NR  
This produces a sharper picture when video images input from the S-VIDEO or VIDEO input terminal  
appear gritty. This function is only available when using VIDEO IN 1, 2, 3 or 4/S-VIDEO IN 1, 2 or 3.  
ENTER  
You can choose a setting from “OFF”, “SOFT” or ”HARD” by using  
or  
and  
to set  
VIDEO NR adjustment.  
OPC (optical control)  
This function automatically adjusts the screen brightness, by sensing the brightness of the area where the  
Rear Projection TV is located. It is activated by setting to “ON” the OPC item in the VIDEO ADJ. menu.  
• Set this function to “OFF” if it is not to be used.  
Note  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Audio Adjust  
Description of Adjustment Items  
Selected item  
BASS  
button  
button  
To decrease bass response.  
To increase bass response.  
To increase treble response.  
To emphasize the right speaker’s volume.  
TREBLE  
BALANCE  
RESET  
To decrease treble response.  
To emphasize the left speaker’s volume.  
To return all adjustments to the factory preset levels.  
TIMER/CLOCK  
VIDEO  
AUDIO  
SCREEN  
PARENT CTRLL EQUISOUND  
CC  
CH SETUP  
SETUP  
MENU  
Press  
to access MAIN  
MENU screen and then use  
AUDIO ADJ.  
Q SOUND  
1
2
3
4
or  
to select “AUDIO”.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
SELECT  
NEXT  
EXIT  
SPEAKER  
MTS  
MENU  
PERSONAL PREFERENCE  
A
B
C
D
ENTER  
Press  
or  
to access the  
to access the  
to move the  
AUDIO  
AUDIO ADJ.  
Q SOUND  
EQUISOUND  
SPEAKER  
MTS  
BASS  
ENTER  
TREBLE  
BALANCE  
RESET  
AUDIO mode.  
SELECT  
NEXT  
BACK  
EXIT  
VOL  
CH  
MENU  
AV MODE  
MUTE  
MENU  
ENTER  
Press  
or  
:AUDIO ADJ.  
BASS  
TREBLE  
BALANCE  
RESET  
‰
‰
‰
INPUT  
ANT-A/B  
AUDIO ADJ. mode.  
SELECT  
NEXT  
BACK  
EXIT  
DISPLAY  
MENU  
ENT. FLASHBACK  
Press  
“
or  
TWIN  
PICTURE  
Q-SOUND  
” mark to an item (e.g. “BASS”)  
VIEW  
MODE  
CH  
ENTER  
and then press  
or  
to  
ADJUST  
BACK  
EXIT  
INPUT  
TITLE  
FF  
BASS  
5‰ -  
MENU  
+
access the BASS Adjust mode.  
Press or to adjust “BASS”,  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
5
6
ENTER  
and then press  
.
MENU  
Press  
to exit.  
• To set other AUDIO  
adjustments, repeat steps 4 to  
5.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Audio Adjust (Continued)  
Other Audio Settings  
Q SOUND  
This function simulates surround sound.  
EQUISOUND  
This function keeps the volume level constant during program changes and commercial breaks.  
INTERNAL SPEAKER SWITCH (SPEAKER)  
This function turns the Rear Projection TV’s internal  
Q SOUND  
EQUISOUND  
SPEAKER  
speakers “ON” or “OFF” when listening to sound from  
external speakers and using the AUDIO OUTPUT  
JACKS. In addition, it is possible to use the built-in  
speakers as the speakers for an external device  
(CENTER-IN). (See page 70.)  
ON  
ON  
SP OFF  
▼
▼
▼
▼
OFF  
▼
OFF  
▼
SP ON  
▼
▼
CENTER-IN  
• The setting sequence is described on the right side.  
MTS……See page 30.  
MENU  
Press  
to access MAIN  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
TIMER/CLOCK  
VIDEO  
AUDIO  
SCREEN  
PARENT CTRLL EQUISOUND  
CC  
MENU screen and then use  
1
2
3
4
5
6
AUDIO ADJ.  
Q SOUND  
or  
to select “AUDIO”.  
PERSONAL PREFERENCE  
A
B
C
D
SELECT  
NEXT  
EXIT  
SPEAKER  
MTS  
CH SETUP  
SETUP  
MENU  
ENTER  
ENTER  
Press  
or  
to access the  
AUDIO  
AUDIO ADJ.  
Q SOUND  
EQUISOUND  
SPEAKER  
MTS  
BASS  
VOL  
CH  
TREBLE  
BALANCE  
RESET  
MENU  
AV MODE  
MUTE  
AUDIO mode.  
SELECT  
NEXT  
BACK  
EXIT  
MENU  
INPUT  
ANT-A/B  
Press  
or  
to move the  
AUDIO  
AUDIO ADJ.  
Q SOUND  
EQUISOUND  
SPEAKER  
MTS  
“
” mark to an item (e.g.  
DISPLAY  
“EQUISOUND”) you want to  
adjust.  
OFF  
SELECT  
NEXT  
BACK  
EXIT  
ENT. FLASHBACK  
MENU  
MENU  
MENU  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
ENTER  
Press  
or  
to access  
:EQUISOUND  
OFF  
ON  
INPUT  
TITLE  
FF  
the EQUISOUND mode.  
REW  
SELECT  
BACK  
EXIT  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
Press  
or  
to turn the  
:EQUISOUND  
OFF  
ON  
EQUISOUND setting “ON” or  
ENTER  
“OFF” and then press  
.
SELECT  
BACK  
EXIT  
Note  
MENU  
Press  
to exit.  
• The Q SOUND works effectively in  
STEREO mode. In MONO (monaural)  
mode, the Q SOUND does not have a  
surround effect.  
• To set other AUDIO adjustments,  
repeat steps 3 to 5.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Audio Adjust (Continued)  
MTS/SAP Select mode  
▼ Switching MTS mode and displaying the broadcasting mode  
MENU  
Press  
to access MAIN  
TIMER/CLOCK  
VIDEO  
AUDIO  
SCREEN  
PARENT CTRLL EQUISOUND  
MENU screen and then use  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
AUDIO ADJ.  
Q SOUND  
1
2
3
4
or  
to select “AUDIO”.  
SELECT  
NEXT  
EXIT  
CC  
CH SETUP  
SETUP  
SPEAKER  
MTS  
PERSONAL PREFERENCE  
MENU  
A
B
C
D
ENTER  
Press  
or  
to access the  
ENTER  
AUDIO  
AUDIO ADJ.  
Q SOUND  
EQUISOUND  
SPEAKER  
MTS  
BASS  
TREBLE  
BALANCE  
RESET  
AUDIO mode.  
SELECT  
NEXT  
BACK  
EXIT  
VOL  
CH  
MENU  
AV MODE  
MUTE  
MENU  
INPUT  
ANT-A/B  
Press  
or  
to move the  
:MTS  
STEREO  
SAP  
cursor to “MTS” and then press  
MONO  
ENTER  
or  
to access the MTS  
DISPLAY  
SELECT  
BACK  
EXIT  
mode.  
ENT. FLASHBACK  
MENU  
TWIN  
PICTURE  
Q-SOUND  
Press  
or  
to select  
:MTS  
STEREO  
SAP  
VIEW  
MODE  
CH  
your desired setting, and then  
press  
MONO  
ENTER  
.
INPUT  
TITLE  
FF  
• For detailed information on the  
settings of “STEREO”, “SAP”  
and “MONO”, see the  
SELECT  
BACK  
EXIT  
REW  
MENU  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
description below.  
DDFC  
MENU  
Press  
to exit.  
• To set other AUDIO adjustments,  
repeat steps 3 to 4.  
5
An on-screen graphic appears when receiving STEREO broadcasts.  
You can enjoy Hi-Fi stereo sound or SAP broadcasts where available.  
• Stereo broadcasts  
Live broadcasts of sports events, shows, concerts, etc. can be received in dynamic stereo sound.  
• SAP broadcasts  
Television broadcasts can be received with either MAIN or SAP sound.  
MAIN sound: The normal program soundtrack. (Monaural or stereo where available.)  
SAP sound: Second language, supplementary commentaries, etc. (SAP sound is monaural.)  
If stereo sound is difficult to hear:  
• You can obtain clearer sound by manually switching to fixed monaural mode.  
• Once MONO mode is selected, the TV sound remains monaural even if the Rear Projection TV receives a stereo  
broadcast. You must switch the mode back to STEREO if you want to hear stereo sound again.  
• Selecting MTS while in the INPUT mode does not change the type of sound; in this case, sound is determined by  
the video source.  
Note  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Screen Adjust  
You can adjust the vertical or horizontal screen size and screen position in this mode.  
(This mode can be used only when the picture is in LETTERBOX, PANORAMIC, or ANAMORPHIC (vertical  
only) view mode. (See page 57.) You can adjust the items by following the tables below.  
Screen adjustment items vary depending on Screen size mode.  
INPUT  
RGB  
Image Format  
480P  
Component  
Video, S-Video  
480I, 480P  
Composite, Y/C  
Screen size mode  
4:3  
POSITION (V)  
–
SIZE (V)  
–
POSITION (H)  
–
SIZE (H)  
–
PANORAMIC  
LETTERBOX  
ANAMORPHIC  
,
,
,
,
,
,
,
,
–
,
,
INPUT  
RGB  
Component  
Image Format  
540P, 720P, 1080I  
720P, 1080I  
Screen size mode  
ANAMORPHIC  
ZOOM  
POSITION (V)  
SIZE (V)  
SIZE (H)  
POSITION (H)  
–
,
–
,
–
Description of Adjustment Items  
POSITION (V)  
moves the on-screen image upward  
moves the on-screen image downward  
SIZE (V)  
POSITION (H)  
SIZE (H)  
makes the on-screen image larger vertically  
makes the on-screen image smaller vertically  
moves the on-screen image leftward  
moves the on-screen image rightward  
makes the on-screen image smaller horizontally  
makes the on-screen image larger horizontally  
RESET  
To return all adjustments to the factory preset levels  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Screen Adjust (Continued)  
MENU  
Press  
to access MAIN  
TIMER/CLOCK  
VIDEO  
AUDIO  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
MENU screen.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
4
SCREEN  
PARENTCTRL  
CC  
CH SETUP  
SETUP  
PERSONAL PREFERENCE  
SELECT  
NEXT  
EXIT  
A
B
C
D
MENU  
Press  
or  
to move  
ENTER  
TIMER//CLOCK  
VIDEO  
AUDIO  
SCREEN  
PARENNTCTRL  
CC  
CH SETUP  
SETUP  
the cursor to “SCREEN”.  
POSITION(V)  
SIZE(V)  
POSITIION(H)  
SIZE(H)  
VOL  
CH  
SELECT  
NEXT  
EXIT  
MENU  
AV MODE  
MUTE  
MENU  
RESET  
INPUT  
ANT-A/B  
ENTER  
Press  
or  
to access  
SCREEN  
POSITION  
(V)  
(H)  
‰
‰
(V)  
SIZE  
POSITION  
the Screen Adjust mode.  
(H)  
SIZE  
SELECT  
NEXT  
BACK  
EXIT  
DISPLAY  
RESET  
ENT. FLASHBACK  
MENU  
TWIN  
PICTURE  
Q-SOUND  
Use  
or  
to select the  
VIEW  
MODE  
CH  
item you want to adjust (e.g.  
“POSITION (V)”), then press  
INPUT  
TITLE  
FF  
ADJUST  
BACK  
EXIT  
REW  
ENTER  
or  
.
SCREEN  
POSITION(V)  
MENU  
6
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
Press  
or  
to adjust  
vertical position, then press  
5
6
ENTER  
.
MENU  
Press  
to exit.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parent Control (V-CHIP operation)  
• This function allows you to restrict TV programs and also allows you to control TV usage based on FCC data.  
This function is for preventing your children from watching programs of mature nature.  
• Restriction of TV programs is based on information about the program’s MPAA rating and the TV Parental  
Guidelines. MPAA is restricted by age. TV Parental Guidelines are restricted by age and contents.  
• Since a TV program may use either the MPAA rating or the TV Guidelines, you should adjust both for complete  
control.  
• The FREEZE and SEARCH functions do not work if the V-CHIP status is set to “ON”. (See page 60 for  
FREEZE screen and page 61 for SEARCH screen.)  
[1] MPAA RATING  
RATING  
G
GENERAL AUDIENCES. All ages admitted.  
PG  
PG-13  
R
PARENTAL GUIDANCE SUGGESTED. Some material may not be suitable for children.  
PARENTS STRONGLY CAUTIONED. Some material may be inappropriate for children under 13.  
RESTRICTED. Under 17 requires accompanying parent or adult guardian.  
NO ONE 17 AND UNDER ADMITTED.  
age base  
NC-17  
X
X Rating is an older rating that is unified with NC-17 but may be encoded in older movies.  
• MPAA RATING (Example)  
Example 2.  
“R” in the age-based  
RATING is blocked. This will  
automatically block the high  
rating “NC-17” and “X” also.  
Example 1.  
1. User setting  
2. Block table  
1. User setting  
2. Block table  
not to  
block  
not to  
block  
“PG-13” in the age-based  
RATING is blocked. This will  
automatically block the high  
ratings “R”, “NC-17” and “X”  
also.  
G
– – – – –  
G
G
–––––  
G
not to  
block  
not to  
block  
PG  
– – – – –  
PG  
–––––  
PG  
PG  
Select  
block  
auto-  
block  
not to  
block  
Select  
block  
PG-13 BLOCK  
BLOCK  
NC-17 BLOCK  
BLOCK  
PG-13 –––––  
BLOCK  
NC-17 BLOCK  
BLOCK  
PG-13  
R
PG-13  
R
age  
base  
age  
base  
R
R
auto-  
block  
auto-  
block  
auto-  
block  
auto-  
block  
NC-17  
X
NC-17  
X
X
X
• MPAA RATING only uses age-based ratings.  
Note  
[2]  
TV PARENTAL GUIDELINES (TV RATINGS)  
← content base →  
Age  
FV  
(Fantasy  
Violence)  
V
S
L
D
RATING  
(Violence)  
(Sexual  
Situation)  
(Adult  
(Sexually  
Language) Suggestive  
Dialogue)  
TV-Y (All children)  
X
X
X
X
X
X
TV-Y7 (Direct to Older Children)  
TV-G (General Audience)  
X
↑
age  
base  
↓
TV-PG (Parental Guidance Suggested)  
TV-14 (Parents Strongly Cautioned)  
TV-MA (Mature Audience Only)  
X
X
X
X
X
X
X
X
X
X
X
X: Content Rating can be set.  
[3] ADDITIONAL MODE  
Besides the above “MPAA RATINGS” and “TV PARENTAL GUIDELINES”, new ratings systems data can  
be downloaded when they become available. (See page 38.)  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parent Control (V-CHIP operation)  
(Continued)  
TV PARENTAL GUIDELINES (example)  
Example 1.1 : Age-Based setting  
Go through all select ratings and select unblocked.  
This will automatically unblock everything.  
:TV RATINGS  
TV-Y  
:BLOCK  
TV-Y7  
TV-G  
FV  
SELECT  
TV-PG  
TV-14  
TV-MA  
D
D
L
L
L
S
S
S
V
V
V
NEXT  
BACK  
EXIT  
MENU  
Example 1.2 : Age-Based setting  
:TV RATINGS  
TV-Y  
:BLOCK  
For “TV-G” select “Block”. This will automatically block the higher age  
ratings “TV-PG”, “TV-14”, “TV-MA” and “TV-G”. Furthermore, the content  
ratings “D”, “L”, “S” and “V” are automatically blocked for  
“TV-PG”, ”TV-14” and “TV-MA”.  
TV-Y7  
TV-G  
FV  
TV-PG  
TV-14  
TV-MA  
D
D
L
L
L
S
S
S
V
V
V
SELECT  
NEXT  
BACK  
EXIT  
MENU  
Example 2.1 : Content-Based setting  
:TV RATINGS  
TV-Y  
For “TV-PG”, “TV-14” and “TV-MA” select unblocked for each content  
rating (“D”, “L”, “S”, “V”) to leave “AGE” blocked for “TV-PG” and “TV-14”  
only.  
:BLOCK  
TV-Y7  
TV-G  
FV  
SELECT  
TV-PG  
TV-14  
TV-MA  
D
D
L
L
L
S
S
S
V
V
V
NEXT  
BACK  
EXIT  
MENU  
Example 2.2 : Content-Based setting  
For “TV-PG”, select “Block” for only “V” (Violence). This will automatically  
block the higher ratings “TV-14-V” and “TV-MA-V” (“TV-14” and “TV-MA”  
for violence content only).  
Please note that with these settings, blocking does NOT occur, if a  
program is rated only “TV-MA”. It must be rated “TV-MA-V” to be blocked.  
:TV RATINGS  
TV-Y  
:BLOCK  
TV-Y7  
TV-G  
FV  
TV-PG  
TV-14  
TV-MA  
D
D
L
L
L
S
S
S
V
V
V
SELECT  
NEXT  
BACK  
EXIT  
MENU  
Example 3 : Reset an Age-Based setting  
For “TV-14”, select “Block” for “Age”.  
This will again automatically block the content ratings “L”, “S”, “V”, “FV”  
for and “TV-MA” in accordance to “TV-14”.  
Please note that the lower age rating “TV-PG” did not change from its  
previous settings.  
:TV RATINGS  
TV-Y  
:BLOCK  
TV-Y7  
TV-G  
FV  
SELECT  
TV-PG  
TV-14  
TV-MA  
D
D
L
L
L
S
S
S
V
V
V
NEXT  
BACK  
EXIT  
MENU  
• Content ratings can be modified but only in the combinations indicated by an “X” on the previous page.  
• Changing a lower age-rating’s content setting to “BLOCK” automatically changes the same higher age-rating’s  
content setting to “BLOCK” regardless of their previous settings.  
Note  
• Changing a lower rating’s “AGE” setting to “BLOCK” automatically changes all higher ratings to “BLOCK” regardless  
of their previous settings.  
• Any “AGE” rating set to unblocked must have its content settings individually set.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set V-CHIP  
Parent Control First Setting  
MENU  
Press  
to access MAIN  
TIMER/CLOCK  
VIDEO  
AUDIO  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
MENU screen.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
4
5
SCREEN  
PARENTCTRL  
CC  
CH SETUP  
SETUP  
SELECT  
NEXT  
EXIT  
PERSONAL PREFERENCE  
A
B
C
D
MENU  
Press  
or  
to move  
ENTER  
TIMER/CLOCK  
VIDEO  
AUDIO  
SCREEN  
PARENTCTRL  
CC  
CH SETUP  
SETUP  
the cursor to “PARENT CTRL”.  
VOL  
CH  
V-CHIP  
VIEW TIMER  
SECRET No.  
MENU  
AV MODE  
MUTE  
SELECT  
NEXT  
EXIT  
MENU  
INPUT  
ANT-A/B  
ENTER  
Press  
or  
to access  
:PARENT CTRL  
V-CHIP  
VIEW TIMER  
SECRET No.  
the SECRET number select mode,  
SELECT  
NEXT  
BACK  
EXIT  
DISPLAY  
ENT. FLASHBACK  
MENU  
TWIN  
PICTURE  
Q-SOUND  
ENTER  
Press  
or  
to access  
:SECRET No.  
INPUT SECRET No.  
VIEW  
MODE  
CH  
NEW SECRET No.  
- - - -  
the NEW SECRET number input  
mode.  
INPUT  
TITLE  
FF  
REW  
BACK  
EXIT  
MENU  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
Enter the 4-digit SECRET number  
:PARENT CTRL  
V-CHIP  
VIEW TIMER  
SECRET No.  
using DIRECT ACCESS (  
) to access the PARENT CTRL  
mode.  
~
SELECT  
NEXT  
BACK  
EXIT  
MENU  
• The V-CHIP and VIEW TIMER mode can be adjusted when the steps 1 ~ 5 are  
finished.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set V-CHIP (Continued)  
MPAA Rating  
TIMER/CLOCK  
VIDEO  
AUDIO  
SCREEN  
PARENTCTRL  
CC  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
MENU  
Press  
to access MAIN  
MENU screen.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
SELECT  
NEXT  
EXIT  
PERSONAL PREFERENCE  
CH SETUP  
SETUP  
MENU  
A
B
C
D
TIMER/CLOCK  
VIDEO  
AUDIO  
SCREEN  
PARENTCTRL  
CC  
Press  
or  
to move  
ENTER  
the cursor to “PARENT CTRL”, then  
press  
ENTER  
or  
to access the  
V-CHIP  
VIEW TIMER  
SECRET No.  
SELECT  
NEXT  
EXIT  
VOL  
CH  
MENU  
AV MODE  
MUTE  
CH SETUP  
SETUP  
MENU  
PARENT CTRL mode.  
The message “INPUT SECRET  
No.” will appear if you have  
already set the secret number,  
PARENTCTRL  
V-CHIP  
VIEW TIMER  
SECRET No.  
MPAA  
TV RATINGS  
OTHERS  
DOWNLOAD  
STATUS  
INPUT  
ANT-A/B  
SELECT  
NEXT  
BACK  
EXIT  
input your secret number by using  
DISPLAY  
DIRECT ACCESS (  
~
).  
MENU  
(See steps 2, 3 on page 41.)  
ENT. FLASHBACK  
:V-CHIP  
MPAA  
TWIN  
PICTURE  
ENTER  
Press  
or  
to access the  
Q-SOUND  
TV RATINGS  
OTHERS  
DOWNLOAD  
STATUS  
VIEW  
MODE  
4
5
CH  
V-CHIP mode.  
SELECT  
NEXT  
BACK  
EXIT  
OFF  
OFF  
INPUT  
TITLE  
FF  
MENU  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
ENTER  
Press  
or  
to access  
VCR/DVD  
POWER  
:MPAA  
G
DDFC  
PG  
PG-13  
R
NC-17  
X
BLOCK  
BLOCK  
BLOCK  
BLOCK  
BLOCK  
the MPAA rating mode, then press  
SELECT  
NEXT  
BACK  
EXIT  
or  
to move the “  
”
MENU  
mark to “PG”.  
ENTER  
Press  
or  
and then use  
:MPAA  
PG  
6
7
8
VIEW  
BLOCK  
or  
to move the cursor  
SELECT  
BACK  
EXIT  
to “BLOCK”.  
MENU  
ENTER  
Press  
to access the  
:MPAA  
G
PG  
PG-13  
BLOCK mode.  
BLOCK  
BLOCK  
BLOCK  
BLOCK  
BLOCK  
SELECT  
NEXT  
BACK  
EXIT  
R
NC-17  
X
MENU  
MENU  
Press  
to exit.  
• If you set “PG” to BLOCK, “PG-13”, “R”, “NC-17” and “X” are automatically blocked.  
• If you set “G” to BLOCK, all RATINGS are automatically blocked.  
• If you set “X” to BLOCK, “G”, “PG”, “PG-13”, “R” and “NC-17” are not blocked.  
Note  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set V-CHIP (Continued)  
TV Rating  
Repeat steps 1 to 4 of MPAA  
Rating on page 36.  
:V-CHIP  
MPAA  
TV RATINGS  
OTHERS  
DOWNLOAD  
STATUS  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
SELECT  
NEXT  
BACK  
EXIT  
OFF  
OFF  
PERSONAL PREFERENCE  
MENU  
A
B
C
D
Press  
or  
to move  
ENTER  
:TV RATINGS  
TV-Y  
TV-Y7  
TV-G  
TV-PG  
TV-14  
TV-MA  
:BLOCK  
the “ ” mark to “TV RATINGS”,  
FV  
VOL  
CH  
SELECT  
ENTER  
D
D
L
L
L
S
S
S
V
V
V
and then press  
or  
.
MENU  
AV MODE  
MUTE  
NEXT  
BACK  
EXIT  
MENU  
INPUT  
ANT-A/B  
Press  
or  
to move  
:TV RATINGS  
TV-Y7  
TV-Y7 FV  
the “ ” mark to “TV-Y7”, and  
then  
SELECT  
NEXT  
BACK  
EXIT  
DISPLAY  
ENTER  
press  
or  
.
ENT. FLASHBACK  
MENU  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
Press  
or  
to move  
:TV RATINGS  
TV-Y7  
VIEW  
INPUT  
TITLE  
FF  
the “ ” mark to “TV-Y7”, then  
4
5
6
7
BLOCK  
REW  
ENTER  
press  
or  
.
SELECT  
BACK  
EXIT  
CH/SKIP  
PAUSE  
STOP  
REC  
MENU  
VCR/DVD  
POWER  
DDFC  
Press  
or  
to move  
:TV RATINGS  
TV-Y7  
VIEW  
the cursor to “VIEW” or “BLOCK”  
(e.g. “BLOCK”).  
BLOCK  
SELECT  
BACK  
EXIT  
MENU  
ENTER  
Press  
BLOCK mode.  
to access the  
:TV RATINGS  
TV-Y7  
TV-Y7 FV  
BLOCK  
BLOCK  
SELECT  
NEXT  
BACK  
EXIT  
MENU  
MENU  
Press  
to exit.  
• If you set “TV-Y7” to BLOCK, “TV-G”, “TV-PG”, “TV-14” and “TV-MA” are automatically blocked “D”, “L”, “S”, “V” and  
“FV”.  
Note  
• You can return to a previous screen by pressing  
to select “BACK” before pressing  
MENU  
to exit.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set V-CHIP (Continued)  
Additional mode  
There may be new or additional rating systems in the future. In that case, please set up as follows and the  
new rating system will be set up automatically.  
Repeat steps 1 to 4 of MPAA  
Rating on page 36 to access  
V-CHIP select mode.  
:V-CHIP  
MPAA  
TV RATINGS  
OTHERS  
DOWNLOAD  
STATUS  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
4
SELECT  
NEXT  
BACK  
EXIT  
OFF  
OFF  
PERSONAL PREFERENCE  
MENU  
A
B
C
D
Press  
“DOWNLOAD”.  
or  
to select  
ENTER  
:V-CHIP  
MPAA  
TV RATINGS  
OTHERS  
SELECT  
NEXT  
BACK  
EXIT  
VOL  
CH  
DOWNLOAD  
STATUS  
OFF  
OFF  
MENU  
AV MODE  
MUTE  
MENU  
INPUT  
ANT-A/B  
ENTER  
Press  
Press  
or  
and then use  
:V-CHIP  
DOWNLOAD  
OFF  
or  
to select “ON”.  
ON  
DISPLAY  
SELECT  
BACK  
EXIT  
ENT. FLASHBACK  
MENU  
TWIN  
PICTURE  
Q-SOUND  
MENU  
to exit.  
VIEW  
MODE  
CH  
INPUT  
TITLE  
FF  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
■ DOWNLOAD V-CHIP DATA  
VCR/DVD  
POWER  
DDFC  
If you watch the program with  
“New Rating System Data”,  
DOWNLOAD screen will be  
displayed.  
1
PLEASE WAIT  
NOW DOWNLOADING  
V-CHIP DATA  
DOWNLOAD screen will  
disappear once the download is  
complete.  
2
• DOWNLOAD will not start if you do not watch the program with New Rating System Data.  
Note  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set V-CHIP (Continued)  
■ Additional mode (Example)  
Before performing the precedure below, download V-CHIP data correctly.  
(See page 38.)  
Repeat steps 1 to 4 of MPAA  
Rating on page 36.  
:V-CHIP  
MPAA  
TV RATINGS  
OTHERS  
DOWNLOAD  
STATUS  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
SELECT  
NEXT  
BACK  
EXIT  
OFF  
OFF  
PERSONAL PREFERENCE  
A
B
C
D
MENU  
Press  
or  
to select  
ENTER  
:OTHERS  
CANADIAN ENGLISH  
CANADIAN FRENCH  
SYSTEM5  
ENTER  
“OTHERS”, then press  
or  
.
VOL  
CH  
SELECT  
NEXT  
BACK  
EXIT  
MENU  
AV MODE  
MUTE  
MENU  
INPUT  
ANT-A/B  
Use  
or  
to move the  
:CANADIAN ENGLISH  
E
C
C8+  
G
PG  
cursor to an item (e.g.  
“CANADIAN ENGLISH”) you want  
BLOCK  
BLOCK  
SELECT  
NEXT  
BACK  
EXIT  
DISPLAY  
ENTER  
to set and then press  
or  
14+  
18+  
.
ENT. FLASHBACK  
MENU  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
Press  
or  
to move the  
:CANADIAN ENGLISH  
C
VIEW  
BLOCK  
cursor to select an item you want  
to set (e.g. “C”), and press  
INPUT  
TITLE  
FF  
4
5
ENTER  
REW  
SELECT  
BACK  
EXIT  
or  
.
CH/SKIP  
PAUSE  
STOP  
REC  
MENU  
VCR/DVD  
POWER  
DDFC  
Press  
or  
to select  
“VIEW” or “BLOCK” from each  
ENTER  
RATING, and press  
.
• Repeat steps 3 to 5 for other settings you want to adjust.  
MENU  
Press  
to exit.  
6
• Includes two types (English mode, French mode), so you are able to download four kinds of modes in Additional  
mode.  
Note  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set V-CHIP (Continued)  
Turn on V-CHIP Block  
ꢀꢀTo operate V-CHIP BLOCK  
Repeat steps 1 to 4 of MPAA  
Rating on page 36.  
:V-CHIP  
MPAA  
TV RATINGS  
OTHERS  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
4
SELECT  
NEXT  
BACK  
EXIT  
DOWNLOAD  
STATUS  
OFF  
OFF  
PERSONAL PREFERENCE  
MENU  
A
B
C
D
Press  
or  
to move  
ENTER  
:V-CHIP  
MPAA  
TV RATINGS  
OTHERS  
the “ ” mark to “STATUS”.  
SELECT  
NEXT  
BACK  
EXIT  
VOL  
CH  
DOWNLOAD  
STATUS  
OFF  
OFF  
MENU  
AV MODE  
MUTE  
MENU  
INPUT  
ANT-A/B  
ENTER  
Press  
Press  
or  
and then use  
:V-CHIP  
STATUS  
OFF  
ON  
or  
to select “ON”.  
DISPLAY  
SELECT  
BACK  
EXIT  
ENT. FLASHBACK  
MENU  
TWIN  
PICTURE  
Q-SOUND  
MENU  
to exit.  
VIEW  
MODE  
CH  
INPUT  
TITLE  
FF  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set V-CHIP (Continued)  
ꢀ To cancel the V-CHIP BLOCK screen while V-CHIP BLOCK is  
activated  
“V-CHIP BLOCK IS ACTIVATED”  
111  
will be displayed if you watch a  
program with Program Rating data  
matching those you have  
configured.  
ANT-A  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
ID‰1  
TV-PG  
DLSV  
PERSONAL PREFERENCE  
A
B
C
D
V-CHIP BLOCK IS ACTIVATED  
• “V-CHIP BLOCK IS ACTIVATED” will  
not be displayed if STATUS is not  
configured to “ON” (See page 40.).  
Note  
ENTER  
VOL  
CH  
MENU  
AV MODE  
MUTE  
ENTER  
Press  
.
INPUT SEECRET No.  
- - - -  
• “INPUT SECRET No.” will be  
displayed.  
2
INPUT  
ANT-A/B  
MENU  
EXIT  
DISPLAY  
Enter the 4-digit SECRET No. using  
ENT. FLASHBACK  
INPUT SECRET No.  
DIRECT ACCESS (  
~
).  
3
TWIN  
PICTURE  
• V-CHIP BLOCK temporarily will  
be canceled.  
Q-SOUND  
VIEW  
MODE  
CH  
MENU  
EXIT  
• If the wrong SECRET number is  
entered, a warning screen appears  
(“SECRET No. IS INCORRECT”), then  
“INPUT SECRET No.” will be  
INPUT  
TITLE  
FF  
Note  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
displayed again. Input the correct  
SECRET number again in this case.  
VCR/DVD  
POWER  
DDFC  
• If you forget “SECRET No.” in step 3, press  
MENU  
to repeat steps 1 to 2 of MPAA  
Rating on page 36, then “INPUT SECRET No.” will be displayed again. Press and  
Note  
hold both ENTER and  
on the front panel of the Rear Projection TV  
MENU  
simultaneously for about five seconds until the message “INPUT SECRET No.”  
disappears, then PARENT CTRL mode will be displayed.  
• If you turn on the Rear Projection TV’s power, then V-CHIP BLOCK will be turned on  
again.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set V-CHIP (Continued)  
ꢀ To change the V-CHIP BLOCK setting (Secret No. is  
registered.)  
Repeat steps 1 to 2 of MPAA Rating on page 36.  
• “INPUT SECRET No.” will be displayed.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
PERSONAL PREFERENCE  
Enter the 4-digit SECRET No. by using DIRECT ACCESS (  
• The V-CHIP select mode will be displayed.  
~
).  
A
B
C
D
ENTER  
Repeat the configuration of the V-CHIP BLOCK on the page 40.  
VOL  
CH  
MENU  
AV MODE  
MUTE  
ꢀ To cancel the V-CHIP setting while V-CHIP BLOCK is set  
In case you forget the Secret No., you can cancel the setting of the V-CHIP  
setting using the method as outlined below.  
INPUT  
ANT-A/B  
DISPLAY  
Repeat steps 1 to 2 of MPAA Rating on page 36, then “INPUT SECRET  
ENT. FLASHBACK  
No.” appears.  
1
2
TWIN  
PICTURE  
Q-SOUND  
MENU  
ENTER  
VIEW  
MODE  
CH  
Press and hold both  
Projection TV simultaneously for about five seconds until the message  
“INPUT SECRET No.” disappears.  
and  
on the front panel of the Rear  
INPUT  
TITLE  
FF  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
MENU  
Press  
to exit.  
VCR/DVD  
POWER  
DDFC  
• The setting of the Secret No. is canceled and the STATUS of the  
V-CHIP changes from ON to OFF.  
3
BEHIND THE COVER  
IN 2  
L-AUDIO-R  
MENU  
ENTER  
VOL  
CH  
VIDEO  
S-VIDEO  
On the front panel of Rear Projection TV  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parent Control (VIEW TIMER)  
VIEW TIMER  
This function allows you to restrict Rear Projection TV viewing times and also to control Rear Projection  
TV usage. This function is for preventing your children from watching too much Rear Projection TV.  
• It is recommended that the “OFF TIME” function and the “VIEWING TIME” function are both set under the  
“VIEW TIMER” function.  
The VIEWING TIME: sets the duration of the viewing time of the Rear Projection TV.  
The OFF TIME: sets the duration the Rear Projection TV may remain off unless the Secret No. is used  
to turn it off.  
• When using the VIEWING TIME function by itself, the Rear Projection TV will start from the time the  
“STATUS” was set to “ON” and will turn off automatically at the set duration.  
• When using the OFF TIME function by itself, the Rear Projection TV cannot be turned on from the time it  
was turned off until the time it was set to.  
■ How to set VIEW TIMER  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
MENU  
Press  
to access MAIN  
TIMER//CLOCK  
VIDEO  
AUDIO  
SCREEN  
PARENTTCTRL  
CC  
CH SETUP  
SETUP  
PERSONAL PREFERENCE  
MENU screen and then use  
1
A
B
C
D
V-CHIP  
or  
to move the cursor to  
“PARENT CTRL”.  
SELECT  
NEXT  
EXIT  
VIEW TTIMER  
SECREET No.  
MENU  
ENTER  
ENTER  
Press  
or  
to access  
VOL  
CH  
PARENNT CTRL  
V-CHIP  
VIEW TTIMER  
SECREET No.  
the PARENT CTRL mode.  
MENU  
AV MODE  
MUTE  
MPAA  
TV RATINGS  
OTHERS  
DOWNLOAD  
STATUS  
INPUT SECRET No.  
SELECT  
NEXT  
BACK  
EXIT  
MENU  
MENU  
EXIT  
INPUT  
ANT-A/B  
Input your secret number by using DIRECT ACCESS (  
~
).  
DISPLAY  
2
3
ENT. FLASHBACK  
PARENNT CTRL  
V-CHIP  
VIEW TIMER  
SECREET No.  
Press  
or  
to move  
VIEWING TIME  
OFF TIME  
STATUS  
the “ ” mark to “VIEW TIMER”.  
TWIN  
PICTURE  
Q-SOUND  
SELECT  
NEXT  
BACK  
EXIT  
VIEW  
MODE  
CH  
MENU  
INPUT  
TITLE  
FF  
REW  
:VIEWW TIMER  
VIEWING TIME---H --M  
ENTER  
Press  
or  
to access  
CH/SKIP  
PAUSE  
STOP  
REC  
OFF TIME  
STATUS  
--H --M  
OFF  
VCR/DVD  
POWER  
4
SELECT  
NEXT  
BACK  
EXIT  
DDFC  
the VIEW TIMER mode, then press  
or to select “VIEWING TIME” or  
MENU  
“OFF TIME” (e.g. “VIEWING TIME”).  
:VIEWW TIMER  
VIEWING TIME--H --M  
ENTER  
Press  
or  
to access  
5
6
ADJUST  
BACK  
EXIT  
the VIEWING TIME mode.  
Press or to adjust  
Note  
MENU  
• Even when the power is turned  
off, the remaining time on the  
VIEWING TIME function will stay  
unchanged. The timer then  
resumes countdown after the  
power is turned on again.  
:VIEWW TIMER  
VIEWINGG TIME 2H 00M  
OFF TIME  
STATUS  
--H --M  
OFF  
the time duration, and then press  
SELECT  
NEXT  
BACK  
EXIT  
ENTER  
.
MENU  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parent Control (VIEW TIMER) (Continued)  
Press  
or  
to move the  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
:VIEWW TIMER  
VIEWINGG TIME 2H 00M  
“
” mark to “STATUS”.  
8
OFF TIME  
STATUS  
--H --M  
OFF  
PERSONAL PREFERENCE  
SELECT  
NEXT  
BACK  
EXIT  
A
B
C
D
MENU  
ENTER  
ENTER  
Press  
or  
and then use  
:VIEWW TIMER  
VOL  
CH  
STATUS  
OFF  
ON  
9
MENU  
AV MODE  
MUTE  
or  
to set “STATUS”  
to “ON” to turn on the VIEW  
TIMER.  
SELECT  
BACK  
EXIT  
MENU  
INPUT  
ANT-A/B  
MENU  
Press  
to exit.  
10  
DISPLAY  
ENT. FLASHBACK  
• If you want to set “OFF TIME”, select “OFF TIME” in step 5.  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
Notice on Remaining VIEWING TIME  
INPUT  
TITLE  
FF  
• For every 30 minute interval, the remaining time will be displayed for four seconds.  
For the last five minutes, the remaining time will be displayed every minute.  
• “0H 00M REMAIN” will be displayed for 10 seconds just before the VIEWING TIME  
is completed.  
Note  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
■ To cancel the VIEW TIMER setting  
Repeat steps 1 to 2 of “How to set VIEW TIMER” on page 43, then  
“INPUT SECRET No.” appears.  
1
MENU  
ENTER  
Press and hold both  
and  
on the front panel of the Rear  
Projection TV simultaneously for about five seconds until the message  
“INPUT SECRET No.” disappears.  
2
MENU  
Press  
to exit.  
• The setting of the Secret No. is canceled and the STATUS of the  
VIEW TIMER changes from ON to OFF.  
3
MENU  
ENTER  
• If you have forgotten your secret number, holding down  
and  
on  
the front panel of the Rear Projection TV simultaneously for about five seconds  
causes the original secret number to be canceled. A new secret number can  
be entered after canceling the original secret number.  
• When you enter the correct SECRET number, the VIEW TIMER mode is displayed.  
If the secret number is incorrect, “SECRET No.IS INCORRECT” is displayed (for  
Note  
two seconds). Input the SECRET number again in this case.  
• While the Rear Projection TV is OFF but the OFF TIME is set, pressing POWER  
cause “TIME OVER” to appear on the screen. If you do nothing, the Rear Projection  
TV will turn off in approximately 30 seconds.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Channel Setup  
If EZ SETUP does not memorize all the channels in your region, follow the instructions below to manually  
memorize the channels.  
AIR/CABLE Setting  
MENU  
Press  
to access MAIN  
TIMER/CLOCK  
VIDEO  
AUDIO  
SCREEN  
PARENTCTRL  
CC  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
MENU screen.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
4
5
SELECT  
NEXT  
EXIT  
PERSONAL PREFERENCE  
CH SETUP  
SETUP  
MENU  
A
B
C
D
Press  
or  
to move  
TIMER/CLOCK  
VIDEO  
AUDIO  
ENTER  
the cursor to “CH SETUP”.  
SCREEN  
AIR/CABLE  
PARENT CTRL CH SEARCH  
VOL  
CH  
SELECT  
NEXT  
EXIT  
MENU  
AV MODE  
MUTE  
CC  
CH MEMORY  
FAVORITES  
UNIV.PLUS  
CH SETUP  
SETUP  
MENU  
INPUT  
ANT-A/B  
ENTER  
Press  
or  
to access  
CH SETUP  
AIR/CABLE  
CH SEARCH  
CH MEMORY  
FAVORITES  
UNIV.PLUS  
STD  
the CH SETUP mode.  
SELECT  
NEXT  
BACK  
EXIT  
DISPLAY  
MENU  
ENT. FLASHBACK  
TWIN  
PICTURE  
Q-SOUND  
Press  
or  
to move  
CH SETUP  
AIR/CABLE  
CH SEARCH  
CH MEMORY  
FAVORITES  
UNIV.PLUS  
VIEW  
MODE  
STD  
CH  
the “ ” mark to “AIR/CABLE”.  
INPUT  
TITLE  
FF  
SELECT  
NEXT  
BACK  
EXIT  
REW  
MENU  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
ENTER  
Press  
or  
to access  
:AIR//CABLE  
AIR  
CABLE STD  
CABLE HRC  
CABLE IRC  
the AIR/CABLE select mode.  
SELECT  
BACK  
EXIT  
MENU  
Press  
or  
to select  
your TV signal mode.  
6
7
CABLE STD  
CABLE HRC  
CABLE IRC  
AIR  
MENU  
Press  
to exit.  
Receivable channels of your Rear Projection TV are:  
AIR channels:  
Note  
VHF: 2 through 13  
UHF: 14 through 69  
CABLE channels:  
1 (HRC and IRC mode only)  
2 through 125 (STD, HRC and IRC)  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Channel setup (Continued)  
Saving Broadcast TV channels to memory (Channel Search)  
Repeat steps 1 to 3 of AIR/  
CABLE Setting on page 45.  
CH SETUP  
AIR/CABLE  
CH SEARCH  
CH MEMORY  
FAVORITES  
UNIV.PLUS  
AIR  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
4
SELECT  
NEXT  
BACK  
EXIT  
PERSONAL PREFERENCE  
MENU  
A
B
C
D
Press  
or  
to move  
ENTER  
CH SETUP  
AIR/CABLE  
CH SEARCH  
CH MEMORY  
FAVORITES  
UNIV.PLUS  
the “ ” mark to “CH SEARCH”.  
VOL  
CH  
SELECT  
NEXT  
BACK  
EXIT  
MENU  
AV MODE  
MUTE  
MENU  
INPUT  
ANT-A/B  
ENTER  
Press  
or  
to access  
:CH SEARCH  
AIR  
1‰  
START  
STOP  
the CH SEARCH mode.  
SELECT  
ENTER  
BACK  
DISPLAY  
ENT. FLASHBACK  
MENU  
EXIT  
TWIN  
PICTURE  
Q-SOUND  
Press  
or  
to move the  
:CH SEARCH  
AIR 1‰  
START  
STOP  
VIEW  
MODE  
CH  
“
” mark to “START”, then press  
ENTER  
.
INPUT  
TITLE  
FF  
SELECT  
ENTER  
BACK  
REW  
• The tuner will search through all  
available channels in your area  
and add them into the Rear  
Projection TV’s memory.  
MENU  
EXIT  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
TO STOP SEARCH  
Press  
or  
to move the  
:CH SEARCH  
AIR 1‰  
START  
STOP  
“
” mark to “STOP”, then press  
ENTER  
.
SELECT  
ENTER  
BACK  
• CH SEARCH will stop at the  
current channel and will not add  
any higher channels.  
MENU  
EXIT  
MENU  
Press  
to exit.  
5
• If you START again while in the CH SEARCH mode, the auto-program will start  
again, and the previously memorized channels will be lost.  
Note  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Channel setup (Continued)  
Adding Weak or Additional Channels or Erasing Unwanted Channels from TV Memory  
Repeat steps 1 to 3 of AIR/CABLE  
Setting on page 45.  
CH SETUP  
AIR/CABLE  
CH SEARCH  
CH MEMORY  
FAVORITES  
UNIV.PLUS  
AIR  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
4
5
6
SELECT  
NEXT  
BACK  
EXIT  
PERSONAL PREFERENCE  
MENU  
A
B
C
D
Press  
or  
to move  
ENTER  
CH SETUP  
AIR/CABLE  
CH SEARCH  
CH MEMORY  
FAVORITES  
UNIV.PLUS  
the “ ” mark to “CH MEMORY”.  
VOL  
CH  
SELECT  
NEXT  
BACK  
EXIT  
MENU  
AV MODE  
MUTE  
MENU  
INPUT  
ANT-A/B  
ENTER  
Press  
or  
to access  
:CH MEMORY  
AIR  
1‰  
TO ADD  
TO ERASE  
the CH MEMORY mode.  
SELECT  
ENTER  
BACK  
DISPLAY  
ENT. FLASHBACK  
MENU  
EXIT  
TWIN  
PICTURE  
Q-SOUND  
Use Channel  
DIRECT ACCESS (  
select each desired channel you  
want to add or erase.  
or  
or  
:CH MEMORY  
VIEW  
MODE  
CH  
AIR  
1‰  
~
) to  
TO ADD  
TO ERASE  
INPUT  
TITLE  
FF  
SELECT  
ENTER  
BACK  
REW  
MENU  
EXIT  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
Use  
or  
to select “TO  
:CH MEMORY  
AIR  
1‰  
ERASE” or “TO ADD” to erase or  
add a channel and then press  
TO ADD  
TO ERASE  
SELECT  
ENTER  
BACK  
ENTER  
.
MENU  
EXIT  
MENU  
Press  
to exit.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Channel setup (Continued)  
FAVORITES  
FAVORITES allows you to program four favorite channels, in four different categories. (A total of 16 channels)  
By setting the FAVORITES channels in advance, you can select your favorite channels easily.  
Press  
,
,
or  
a number of times until your favorite channel is selected.  
A
D
B
C
Repeat steps 1 to 3 of AIR/CABLE  
Setting on page 45.  
CH SETUP  
AIR/CABLE  
CH SEARCH  
CH MEMORY  
FAVORITES  
UNIV.PLUS  
STD  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
SELECT  
NEXT  
BACK  
EXIT  
PERSONAL PREFERENCE  
MENU  
MENU  
MENU  
A
B
C
D
Press  
or  
to move  
ENTER  
CH SETUP  
AIR/CABLE  
CH SEARCH  
CH MEMORY  
FAVORITES  
UNIV.PLUS  
the “ ” mark to “FAVORITES”.  
2
3
4
5
SELECT  
NEXT  
BACK  
EXIT  
VOL  
CH  
MENU  
AV MODE  
MUTE  
INPUT  
ANT-A/B  
ENTER  
Press  
or  
to access  
:FAVOORITES  
A
B
C
---  
---  
---  
---  
D
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
the FAVORITES mode.  
DISPLAY  
SELECT  
BACK  
EXIT  
ENT. FLASHBACK  
TWIN  
PICTURE  
Q-SOUND  
Press  
to move  
the “ ” mark to the desired  
position.  
,
,
or  
:FAVOORITES  
VIEW  
MODE  
A
B
C
D
CH  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
INPUT  
TITLE  
FF  
SELECT  
BACK  
EXIT  
REW  
MENU  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
Press DIRECT ACCESS (  
) to input the channel number  
into the memory.  
~
:FAVORITES  
A
B
C
D
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
120  
---  
---  
---  
---  
---  
SELECT  
BACK  
EXIT  
MENU  
• Repeat steps 4 to 5 to input more CHANNEL numbers.  
MENU  
Press  
to exit.  
6
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Channel setup (Continued)  
UNIVERSAL PLUS Function  
VCR/DVD input mode will be selected automatically when pressing VCR/DVD player PLAY button on the  
UNIVERSAL REMOTE CONTROL. (For VCR/DVD player connections, see pages 9 ~ 11)  
Repeat steps 1 to 3 of AIR/  
CABLE Setting on page 45.  
CH SETUP  
AIR/CABLE  
CH SEARCH  
CH MEMORY  
FAVORITES  
UNIV.PLUS  
AIR  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
4
5
6
SELECT  
NEXT  
BACK  
EXIT  
PERSONAL PREFERENCE  
MENU  
A
B
C
D
Press  
or  
to move the  
ENTER  
CH SETUP  
AIR/CABLE  
CH SEARCH  
CH MEMORY  
FAVORITES  
UNIV.PLUS  
“
” mark to “UNIV. PLUS”.  
VOL  
CH  
SELECT  
NEXT  
BACK  
EXIT  
MENU  
AV MODE  
MUTE  
VCR  
DVD  
MENU  
INPUT  
ANT-A/B  
ENTER  
Press  
or  
to access  
:UNIV.PLUS  
VCR  
DVD  
OFF  
the UNIV. PLUS mode.  
SELECT  
NEXT  
BACK  
EXIT  
DISPLAY  
ENT. FLASHBACK  
MENU  
TWIN  
PICTURE  
Q-SOUND  
Press  
or  
to select  
:UNIVV.PLUS  
VCR  
OFF  
VIEW  
MODE  
CH  
“VCR” or “DVD” (e.g. “VCR”), then  
CH3  
INPUT  
TITLE  
FF  
CH4  
INPUT1  
INPUT2  
ENTER  
press  
or  
.
SELECT  
BACK  
EXIT  
REW  
MENU  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
Press  
channel or Input mode.  
or  
to select  
:UNIVV.PLUS  
VCR  
OFF  
CH3  
CH4  
INPUT1  
INPUT2  
SELECT  
BACK  
EXIT  
MENU  
MENU  
Press  
to exit.  
• It is not possible to select the same input mode for VCR and DVD player.  
• The DVD input must be set to “OFF” or “INPUT1” ~ “INPUT5”.  
Note  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup  
LANGUAGE  
The language for the ON SCREEN DISPLAY can be set to ENGLISH, SPANISH or FRENCH.  
MENU  
Press  
to access MAIN  
TIMER/CLOCK  
VIDEO  
AUDIO  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
MENU screen.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
4
5
6
SCREEN  
PARENTCTRL  
CC  
CH SETUP  
SETUP  
SELECT  
NEXT  
EXIT  
PERSONAL PREFERENCE  
A
B
C
D
MENU  
Press  
cursor to “SETUP”.  
or  
to move the  
ENTER  
TIMER//CLOCK  
VIDEO  
AUDIO  
SCREEN  
PARENT CTRL  
CC  
LANGUAGE  
GRAY SCREEN  
ENERGY SAVE  
CONVER.ADJ.  
INPUT MODE  
CH/INNPUT ID  
VOL  
CH  
MENU  
AV MODE  
MUTE  
SELECT  
NEXT  
CH SETUP  
SETUP  
MENU  
EXIT  
INPUT  
ANT-A/B  
ENTER  
Press  
or  
to access  
SETUP  
LANGUAGE  
ENGLISH  
GRAY SCREEN  
ENERGY SAVE  
CONVER.ADJ.  
INPUT MODE  
CH/INPUTID  
the SET UP mode.  
SELECT  
NEXT  
BACK  
EXIT  
DISPLAY  
MENU  
ENT. FLASHBACK  
TWIN  
PICTURE  
Q-SOUND  
ENTER  
Press  
or  
to access  
:LANGUAGE  
ENGLISH  
ESPANOL  
VIEW  
MODE  
CH  
FRANCAIS  
the LANGUAGE mode.  
INPUT  
TITLE  
FF  
SELECT  
BACK  
EXIT  
REW  
MENU  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
Press  
or  
to select  
:IDIOMA  
ENGLISH  
ESPANOL  
FRANCAIS  
“ENGLISH”, “ESPAÑOL”  
(SPANISH) or “FRANÇAIS”  
(FRENCH).  
SELECCION  
REGRESAR  
SALIDA  
MENU  
MENU  
Press  
to exit.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup (continued)  
GRAY SCREEN  
Automatically turns the screen gray if a broadcast signal is not received.  
MENU  
Press  
to access MAIN  
TIMER/CLOCK  
VIDEO  
AUDIO  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
MENU screen.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
4
5
6
SCREEN  
PARENTCTRL  
CC  
CH SETUP  
SETUP  
SELECT  
NEXT  
EXIT  
PERSONAL PREFERENCE  
MENU  
A
B
C
D
Press  
or  
to move the  
ENTER  
SETUP  
LANGUAGE  
cursor to “SETUP”, and then  
ENGLISH  
GRAY SCREEN  
ENERGY SAVE  
CONVER.ADJ.  
INPUT MODE  
CH/INPUTID  
SELECT  
NEXT  
BACK  
EXIT  
VOL  
CH  
ENTER  
press  
or  
to access the  
MENU  
AV MODE  
MUTE  
MENU  
SET UP mode.  
INPUT  
ANT-A/B  
Press  
or  
to move the  
SETUP  
LANGUAGE  
“
” mark to “GRAY SCREEN”.  
GRAY SCREEN  
ENERGY SAVE  
CONVER.ADJ.  
INPUT MODE  
CH/INPUT ID  
OFF  
SELECT  
NEXT  
BACK  
EXIT  
DISPLAY  
MENU  
ENT. FLASHBACK  
TWIN  
PICTURE  
Q-SOUND  
ENTER  
Press  
or  
to access  
:GRAY SCREEN  
OFF  
ON  
VIEW  
MODE  
CH  
the GRAY SCREEN select mode.  
INPUT  
TITLE  
FF  
SELECT  
BACK  
EXIT  
REW  
MENU  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
Press  
cursor to “ON”.  
or  
to move the  
:GRAY SCREEN  
OFF  
ON  
SELECT  
BACK  
EXIT  
MENU  
MENU  
Press  
to exit.  
• When the GRAY SCREEN function has been set to ON, the screen will flicker if the  
broadcast signal is weak.  
Note  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup (Continued)  
ENERGY SAVE  
This feature lets you lower the power consumption of your Rear Projection TV which in turn saves  
electricity and minimizes the impact on the environment. When this feature is turned on, it reduces the  
brightness of the Rear Projection TV to a level that consumes approximately 20 percent less energy than  
when the feature is turned off.  
The reduction in brightness will be less noticeable under low room lighting conditions.  
MENU  
Press  
to access MAIN  
TIMER/CLOCK  
VIDEO  
AUDIO  
SCREEN  
PARENTT CTRL  
CC  
SLEEP TIME  
TV-ON TIME  
CLOCK SET  
MENU screen.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
2
3
4
5
6
SELECT  
NEXT  
EXIT  
PERSONAL PREFERENCE  
CH SETUP  
SETUP  
MENU  
MENU  
MENU  
A
B
C
D
Press  
or  
to move the  
ENTER  
SETUP  
LANGUAGE  
cursor to “SETUP”, and then  
ENGLISH  
GRAY SCREEN  
ENERGY SAVE  
CONVER.ADJ.  
INPUT MODE  
CH/INPUTID  
SELECT  
NEXT  
BACK  
EXIT  
VOL  
CH  
ENTER  
press  
or  
to access the  
MENU  
AV MODE  
MUTE  
SETUP mode.  
INPUT  
ANT-A/B  
Press  
or  
to move the  
SETUP  
“
” mark to “ENERGY SAVE”.  
LANGUAGE  
GRAY SCREEN  
ENERGY SAVE  
CONVER.  
INPUT MODE  
CH/INPUT ID  
SELECT  
NEXT  
BACK  
EXIT  
OFF  
DISPLAY  
ENT. FLASHBACK  
TWIN  
PICTURE  
Q-SOUND  
ENTER  
Press  
or  
to access  
:ENERGY SAVE  
OFF  
ON  
VIEW  
MODE  
CH  
the ENERGY SAVE mode.  
INPUT  
TITLE  
FF  
SELECT  
BACK  
EXIT  
REW  
MENU  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
Press  
or  
to move the  
:ENERGY SAVE  
OFF  
ON  
cursor to “ON” or “OFF”.  
SELECT  
BACK  
EXIT  
MENU  
MENU  
Press  
to exit.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup (Continued)  
CONVERGENCE ADJUST  
Your Rear Projection TV has three color projection tubes: one for red, one for green, one for blue. When  
mixed together in the proper proportion, the output of these three color tubes can produce any color. To  
produce these colors, however, the beams must be precisely aligned over each other so that the colors  
can be mixed. The process of aligning these picture beams is called “convergence”.  
Over a period of time, the picture tubes can drift out of alignment due to normal bumps and vibrations or  
moving the Rear Projection TV. If you move your Rear Projection TV, or if, after a time, you notice color  
rings or halos around objects in the picture, you may want to converge (align) the colors.  
Properly converged, the lines appear white, which is actually a combination of the outputs of the three  
color tubes. The output of the green tube is stationary. The outputs of the red and blue tubes can be  
adjusted.  
To simplify convergence, this Rear Projection TV incorporates a feature to allow you to display a test  
pattern of horizontal and vertical lines at nine different locations on the screen. Simply use the remote  
control to adjust the red and blue colors to match the green.  
Repeat steps 1 and 2 of the  
ENERGY SAVE setting on  
SETUP  
LANGUAGE  
1
GRAY SCREEN  
ENERGY SAVE  
CONVER.ADJ.  
INPUT MODE  
CH/INPUTID  
page 52.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
SELECT  
NEXT  
BACK  
EXIT  
Press  
or  
to move the  
MENU  
PERSONAL PREFERENCE  
“
” mark to “CONVER. ADJ.”  
A
B
C
D
ENTER  
ENTER  
Press  
or  
to  
:CONVER.ADJ.  
OFF  
ON  
2
3
VOL  
CH  
MENU  
AV MODE  
MUTE  
access the CONVER. ADJ. mode.  
SELECT  
ENTER  
BACK  
MENU  
EXIT  
INPUT  
ANT-A/B  
Press  
“ON” and then press  
or  
to select  
DISPLAY  
ENTER  
or  
Red  
ENT. FLASHBACK  
to display nine crosshatches.  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
INPUT  
TITLE  
FF  
REW  
Use  
,
,
or  
to  
CH/SKIP  
PAUSE  
STOP  
REC  
4
VCR/DVD  
POWER  
move the red cross in the center  
to match it to the green cross.  
• When adjusting convergence,  
always start at the center of the  
screen.  
DDFC  
Red  
• Four lines surrounding a  
crosshatch indicate the point  
being adjusted. The color of  
these surrounding lines  
indicates the color being  
adjusted.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup (Continued)  
Specify the crosshatch which stands  
out with a comparatively uneven  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
5
color by using  
bottom right)*,  
~
. (e.g.  
PERSONAL PREFERENCE  
A
B
C
D
Red  
press  
,
,
or  
to  
move the red cross to match it to  
the green cross.  
ENTER  
VOL  
CH  
* Buttons which corresponds to each crosshatch  
MENU  
AV MODE  
MUTE  
INPUT  
ANT-A/B  
DISPLAY  
Red  
ENT. FLASHBACK  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
INPUT  
TITLE  
FF  
REW  
ENTER  
Press  
use  
and then  
,
CH/SKIP  
PAUSE  
STOP  
REC  
6
7
VCR/DVD  
POWER  
,
or  
to  
DDFC  
move the blue cross to match it to  
the yellow cross.  
Blue  
Apply step 5 and match the blue  
cross to the yellow cross.  
Blue  
Press the  
control to confirm the adjustment.  
• After steps 1-7 are performed, turning the power off also saves  
your adjustment into memory without pressing  
PERSONAL PREFERENCE button on the remote  
D
IMPORTANT  
8
.
D
Press  
to exit.  
MENU  
9
• If you do not wish to save your adjustment data into memory, press the remote  
AV MODE  
control  
. When the Rear Projection TV is turned on again, your old  
Note  
convergence data will be restored.  
• On-screen display MENU text may become offset when the signal is lost. Restoring  
the signal and the MENU text resumes normal appearance.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup (Continued)  
INPUT MODE  
You can select the input signal in INPUT 3 and INPUT 4. The setting items vary in INPUT 3 and INPUT 4.  
Repeat steps 1 and 2 of the  
ENERGY SAVE setting  
on page 52.  
1
SETUP  
LANGUAGE  
GRAY SCREEN  
ENERGY SAVE  
CONVER.ADJ.  
INPUT MODE  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
SELECT  
NEXT  
BACK  
EXIT  
Press  
or  
to move the  
PERSONAL PREFERENCE  
INPUT 3  
“
” mark to “INPUT MODE”.  
A
B
C
D
MENU  
CH/INPUTID INPUT 4  
ENTER  
ENTER  
Press  
or  
to  
:INPUT MODE  
INPUT3  
2
3
VOL  
CH  
INPUT4  
AUTO  
MENU  
AV MODE  
MUTE  
access the INPUT MODE.  
SELECT  
NEXT  
BACK  
EXIT  
MENU  
INPUT  
ANT-A/B  
Press  
or  
to select  
INPUT No. which you want to  
DISPLAY  
:INPUUT MODE  
INPUT4  
AUTO  
VIDEO  
HD/DVD  
ENTER  
adjust, and then press  
or  
ENT. FLASHBACK  
to access the INPUT MODE  
(e.g. INPUT 4).  
TWIN  
PICTURE  
SELECT  
BACK  
EXIT  
Q-SOUND  
MENU  
VIEW  
MODE  
CH  
INPUT  
TITLE  
FF  
Press  
instrument (HD/DVD).  
or  
to select the  
:INPUT MODE  
INPUT4  
AUTO  
REW  
4
5
CH/SKIP  
PAUSE  
STOP  
REC  
VIDEO  
HD/DVD  
VCR/DVD  
POWER  
SELECT  
BACK  
EXIT  
DDFC  
MENU  
Press  
to exit.  
MENU  
Description of setting items  
INPUT 3 : Select input port and input signal between VIDEO and RGB.  
VIDEO : Only VIDEO  
RGB :  
RGB signal  
INPUT 4 : Select input port and input signal from AUTO, VIDEO or HD/DVD.  
AUTO : This setting automatically distinguishes the input source (input signal).  
VIDEO : Only VIDEO  
HD/DVD : To connect a player which has component video output terminals, such as DVD player, etc.  
The signal is chosen automatically (480I/480P/720P/1080I).  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup (Continued)  
CH/INPUT ID  
With the “CH ID” of the CH/INPUT ID function, it is possible to input the names (up to four letters) of  
channels, for example CNN, NBC. With the “INPUT ID”, it is possible to input names (up to four letters) for  
each of the input terminals on the Rear Projection TV (for example, VCR, DVD, STB). This function makes  
it easy to select the source being displayed on the screen.  
Repeat steps 1 and 2 of the  
ENERGY SAVE setting on  
page 52.  
SETUP  
LANGUAGE  
GRAY SCREEN  
ENERGY SAVE  
CONVER.ADJ.  
INPUT MODE  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
SELECT  
NEXT  
BACK  
EXIT  
PERSONAL PREFERENCE  
CH/INPUT ID CH ID  
Press  
or  
to move the  
A
B
C
D
MENU  
INPUT ID  
“
” mark to “CH/INPUT ID”.  
ENTER  
:CH/INPUTID  
CH ID  
INPUT ID  
ENTER  
Press  
or  
to access  
VOL  
CH  
MENU  
AV MODE  
MUTE  
2
3
4
SELECT  
NEXT  
BACK  
EXIT  
the CH/INPUT ID mode.  
INPUT  
ANT-A/B  
Press  
or  
to select  
:CH/INPUTID  
CH ID  
DISPLAY  
“CH ID” or “INPUT ID” and then  
____  
STD  
11  
RESET  
ENT. FLASHBACK  
SELECT  
NEXT  
BACK  
EXIT  
ENTER  
press  
or  
(eg. “CH ID”).  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
Use  
ACCESS (  
or  
, or DIRECT  
) to select  
:CH/INPUTID  
CH ID  
INPUT  
TITLE  
FF  
~
____  
STD  
13  
REW  
channel whose name you want to  
ENTER  
register. Then press  
.
CH/SKIP  
SELECT  
BACK  
EXIT  
PAUSE  
STOP  
REC  
MENU  
VCR/DVD  
POWER  
DDFC  
Use  
input the name.  
,
,
or  
to  
:CH/INPUTID  
CH ID  
5
6
STD  
13  
ABCD  
•
•
,
... Selects a letter  
SELECT  
BACK  
EXIT  
,
......... Changes the place  
where a letter is input  
MENU  
ENTER  
Press  
.
• Repeat steps 5 to 7 to input more CH/INPUT IDs.  
MENU  
Press  
to exit.  
7
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing Screen Size  
The size of the picture can be adjusted to the following screen sizes.  
VIEW  
MODE  
4:3  
PANORAMIC  
LETTERBOX  
PERSONAL PREFERENCE  
Press  
.
A
B
C
D
ANAMORPHIC  
1
VIEW  
• Each time MODE is pressed, the mode changes in the order above.  
ENTER  
VOL  
CH  
(4:3 image)  
MENU  
AV MODE  
MUTE  
Suitable for viewing news or sitcoms. Video  
software can be viewed in its original screen frame  
size.  
4:3:  
INPUT  
ANT-A/B  
DISPLAY  
Suitable for viewing news or sports  
programs.  
Movies or Sports programs can be viewed  
with an expansive powerful image.  
PANORAMIC:  
LETTERBOX:  
ENT. FLASHBACK  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
Suitable for viewing Vista size and other  
such movie images. Provides a more  
expansive, powerful image. This screen  
size is also convenient when viewing a  
Cinemascope size image that has subtitles.  
INPUT  
TITLE  
FF  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
ANAMORPHIC:  
Suitable for viewing wide-screen images  
or anamorphic DVDs.  
IMPORTANT!  
VIEW  
In case of a 540P/720P/1080I signal, pressing MODE switches the view mode between ANAMORPHIC and ZOOM.  
ZOOM:  
Note  
• Black bands may remain at the top and bottom of the screen depending  
on the size of the picture (such as in the case of Cinemascope size).  
• Some portions of captions may be missing with certain types of  
commercially available video software. When this happens, switch the  
screen to the optimum screen size with the screen size button, and  
adjust screen scroll or vertical size.  
• This TV is provided with these view modes to display images with  
various aspect ratios.  
When 4:3 images are fully displayed on a wide TV screen in the  
PANORAMIC mode, LETTERBOX mode, or ANAMORPHIC mode,  
some parts of the images may be cut off or distorted, as described in  
the above illustrations.  
•
Continuous operation for extended periods in 4:3 mode may burn the  
screen. Marantz thus recommends that use of this mode should be limited.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting DDFC Mode or AV Mode  
Selecting DDFC Mode  
Press
DDFC  
.
1
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
• You can select the picture quality from  
three different modes.  
PERSONAL PREFERENCE  
• Each time
DDFC
is pressed, the mode  
changes in the order below.  
A
B
C
D
540P  
540P  
(Progressive)  
1080I  
(AUTO)  
ENTER  
1080I  
(Interlace)  
VOL  
CH  
MENU  
AV MODE  
MUTE  
540P  
(Progressive)  
This mode is used to display  
still images or graphics  
without flickering.  
1080I (AUTO)  
INPUT  
ANT-A/B  
1080I  
(AUTO)  
This mode is used to enjoy  
movies on DVD without  
flickering.  
DISPLAY  
ENT. FLASHBACK  
1080I  
(Interlace)  
This mode is used to enjoy  
movies on DVD with 3:2  
pull-down.  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
1080I  
INPUT  
TITLE  
FF  
REW  
• Selecting the mode “540P” reduces screen flickering when using a video game  
machine.  
• If the input signal is 480P, 1080I Auto mode cannot be accessed.  
CH/SKIP  
PAUSE  
STOP  
REC  
Note  
VCR/DVD  
POWER  
DDFC  
Selecting AV Mode  
You can select the picture setting which displays the video in the most desirable way.  
AV MODE  
Press  
.
1
AV MODE  
• Each time  
is pressed, the mode changes in the following order.  
DYNAMIC  
STD  
USER  
SOFT  
DYNAMIC: an actively forceful image definition mode  
SOFT: a soft and gentle image definition mode  
STD: a standard image definition mode suited for everybody as well as for  
many types of VCR tapes and DVD discs.  
• DYNAMIC/STD/SOFT  
A common value is set for all input signals.  
• USER  
Note  
A different value is set for each of the TV’s terminals, INPUT 1-5.  
(When switching to a different input, a specific value is set.)  
DDFC Mode change only  
operates with 480I, 480P,  
or conventional  
broadcast signals. It has  
no effect on other  
formats.  
• The VIDEO ADJ. or PRO ADJ. settings can be memorized in each AV mode (see  
pages 25 - 26 for Video Adjust.)  
Note  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Multi-screen Function  
View two Screens (TWIN PICTURE Screen)  
The screen can be split vertically, making it possible to view different images on the left and right.  
TWIN  
PICTURE  
Press  
.
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
12  
10  
ANT-B  
ANT-A  
• Press DIRECT ACCESS (  
~
) or  
PERSONAL PREFERENCE  
Main picture  
Sub-picture  
or to select your desired channel for the  
A
B
C
D
Main picture.  
• Press  
to select your desired  
CH  
ENTER  
channel for the Sub-picture.  
VOL  
CH  
MENU  
AV MODE  
MUTE  
• The screen on which “ ” is displayed is the main picture, and the other screen is  
the sub-picture. Sound will be output for the main picture.  
• Regular operations can be performed for the main picture.  
Note  
• When the SELECT button is pressed, “ ” will move to the other screen.  
• The closed caption function does not work in the Twin picture screen.  
INPUT  
ANT-A/B  
DISPLAY  
TWIN  
PICTURE  
Press  
to make the left part  
ENT. FLASHBACK  
10  
12  
ANT-A  
ANT-B  
2
of the screen become larger.  
TWIN  
PICTURE  
Q-SOUND  
• The only image that can be enlarged is  
the left one. It is not possible to enlarge  
the image on the right.  
VIEW  
MODE  
CH  
INPUT  
TITLE  
FF  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
TWIN  
PICTURE  
Press  
to return to the initial  
VCR/DVD  
POWER  
DDFC  
3
screen.  
• In the TWIN PICTURE screen mode, it is not possible to display two images from  
the same input source.  
• The broadcasting signal in ANT-A, ANT-B in the TWIN PICTURE screen mode  
cannot change as in the normal screen.  
Note  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Multi-screen Function (Continued)  
Making Notes From the Program Content (Freeze Screen)  
The screen can be frozen, such as for taking down a recipe from a cooking program or address for  
entering a contest.  
Press
FREEZE  
.
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
• The freeze function serves as a memo  
function. By changing a full screen into  
twin picture mode the left screen is  
frozen. This function is convenient when  
information you want to take down is  
displayed on the screen.  
PERSONAL PREFERENCE  
Still screen  
Move screen  
A
B
C
D
ENTER  
VOL  
CH  
MENU  
AV MODE  
MUTE  
Press FREEZE again to restore to full  
screen.  
2
INPUT  
ANT-A/B  
• This function is operable only with the normal screen.  
• The Closed Caption function does not work when Freeze is used.  
• The Freeze Screen function is disabled when “STATUS” of the V-CHIP is “ON.”  
DISPLAY  
Note  
ENT. FLASHBACK  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
INPUT  
TITLE  
FF  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Multi-screen Function (Continued)  
Searching for a Program on a Different Channel (Search Screen)  
The screen on the right side can be divided into three different screens, making it possible to search for  
programs or enjoy multiple images.  
Press
SEARCH
to display 3-SEARCH  
screen.  
2
6
ANT-A  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
1
3
4
PERSONAL PREFERENCE  
A
B
C
D
ENTER  
• Each time SEARCH is pressed, the screen mode changes in the following order.  
VOL  
CH  
MENU  
AV MODE  
MUTE  
Normal screen  
3-SEARCH screen  
CH  
• Pressing  
/
changes the channels of the three subscreens into three new  
CH  
INPUT  
ANT-A/B  
screens.  
Note  
• It is not possible to alter the color or the sound of the Search picture.  
• Sound output is limited to the main picture.  
DISPLAY  
ENT. FLASHBACK  
TWIN  
PICTURE  
To enlarge one of three subscreens  
SELECT  
(1) Press  
selected.  
a number of times until the screen you want to enlarge is  
VIEW  
MODE  
CH  
INPUT  
TITLE  
FF  
ENTER  
(2) Press  
to enlarge selected screen.  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
• Continuous operation for extended periods in SEARCH screen mode may burn the  
screen.  
Marantz thus recommends that use of the Search function should be limited.  
• The 3-SEARCH screen function is disabled when “STATUS” of the V-CHIP is “ON”.  
• The Closed Caption function does not work when using the 3-Search function.  
VCR/DVD  
POWER  
DDFC  
Note  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Multi-screen Function (Continued)  
Interchanging the Left and Right Screens you are Currently Watching (Swap Screen)  
Use SWAP to interchange the left and right screens you are currently watching.  
TWIN  
Press PICTURE to use the  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
12  
10  
ANT-B  
1
2
twin picture display.  
ANT-A  
A picture  
B picture  
PERSONAL PREFERENCE  
A
B
C
D
ENTER  
Press SWAP to interchange the left  
and right screens.  
VOL  
CH  
12  
10  
MENU  
AV MODE  
MUTE  
ANT-A  
ANT-B  
B picture  
INPUT  
ANT-A/B  
DISPLAY  
• This operation is only performed during the twin picture display.  
• If you use the SWAP function, the Antenna signal (ANT-A / ANT-B) interchanges as  
well. (See the step 2 above.)  
ENT. FLASHBACK  
Note  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
Scanning other channels during a commercial break  
(Commercial Skip)  
INPUT  
TITLE  
FF  
REW  
During airing of commercial message, you can watch other programs by using  
the Commercial Skip function.  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
When a commercial break occurs,  
6
ANT-A  
CM SKIP  
1
press  
to move the main  
picture to the subpicture on the  
right.  
• While you are watching other  
channels you can check the  
subpicture.  
10  
6
ANT-A  
ANT-B  
CM SKIP  
Press  
when the program in the subpicture starts again.  
• Then the subpicture moves to the main picture.  
2
• CM SKIP only works with the tuner. It does not work with Video Input/Component.  
Note  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation of the Remote Control for Other Devices  
ENTER  
VCR/DVD  
POWER  
VOL  
CH  
MENU  
AV MODE  
MUTE  
CH/SKIP  
REW  
INPUT  
ANT-A/B  
REW  
STOP  
DISPLAY  
PLAY  
FF  
ENT. FLASHBACK  
TWIN  
FF  
STOP  
PICTURE SEARCH Q-SOUND  
VIEW  
CH  
FREEZE SELECT  
MODE  
TITLE  
INPUT  
SWAP  
REW  
CM SKIP  
PAUSE  
PLAY FF  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
STOP  
REC  
■ Universal Remote Control  
With the purchase of your Rear Projection TV you also have received the latest innovation in remote control  
technology. With its easy-to-use push button keyboard, your remote can control your Rear Projection TV and  
most infrared remote controlled VCRs, DVD players, cable TV converters and DTV STB as well.  
• Depending on the model, year produced, brand and type of VCR/DVD player, some models may not be compatible  
with the remote control.  
• Some brands of Cable TV converter Box may not enable channel selection until  
ENT.  
Note  
is pressed.  
■ Using your Remote control with a DTV STB (Decoder)  
After installing the batteries, press DTV STB. (If you can change the channel of the DTV STB (Decoder) by  
pressing or on the remote control, the unit is in the DTV mode.)  
■ Using Your Remote With Your Rear Projection TV  
After installing the batteries, set the DTV STB-TV-CATV on the remote to the TV position. (If you can change  
the channel of the TV by pressing  
or  
on the Remote Control, the unit is in the TV position.)  
■ “Identifying” Remote VCR/DVD player, Cable TV Converters and DTV STB  
Your remote control has been set at the factory to operate your Rear Projection TV and many remote controlled  
VCRs, DVD players, Cable Converters and DTV STB. However, in some cases an easy one-time set-up step  
may be necessary before the remote will operate VCRs, DVD players, Cable Converters and DTV STB.  
• In this set-up step, the remote locates and memorizes the remote control transmitter code for the VCR, DVD  
player, Cable Converter or DTV STB.  
• Once “identified”, the remote sends the proper remote signals to operate your equipment.  
• This identification step will not have to be repeated until power to the remote is interrupted, e.g. due to  
battery replacement.  
■ USING YOUR REMOTE CONTROL WITH A VCR OR DVD PLAYER  
Once you make certain the remote control has “identified” your remote controlled VCR or DVD player, the  
remote control is ready to operate your equipment. The various VCR/DVD function buttons on the remote  
control will not operate your VCR/DVD player unless those features are available on the VCR/DVD player.  
• All VCR/DVD buttons will operate whether the remote control is in the TV or CATV modes.  
• For detailed information on the use of the VCR or DVD player, refer to the operation manual of the VCR or  
DVD player.  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation of the Remote Control for Other Devices (Continued)  
How to Identify a VCR  
The remote control may already be set to operate your VCR. Try this initial  
check to see whether it will be necessary to “identify” your VCR.  
VCR/DVD  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
POWER  
(1) Point the remote towards the VCR and press  
(2) Does the remote turn the VCR ON and OFF?  
.
PERSONAL PREFERENCE  
• If yes, the remote is ready to operate the VCR and no further steps are  
A
B
C
D
needed.  
• If no, continue to the “identify” section.  
ENTER  
■ To Identify Your VCR – Direct Entry Method.  
Use the following steps and the list (on page 65) to quickly find the remote  
control code for your VCR.  
• First look up your VCR’s remote control code number (on page 65) before  
VOL  
CH  
MENU  
AV MODE  
MUTE  
continuing the direct code entry steps.  
VCR/  
TV  
INPUT  
ANT-A/B  
(1) Press  
and the button lights.  
DISPLAY  
DISPLAY  
(2) While holding down  
, press  
on your remote control.  
ENT. FLASHBACK  
VCR/  
TV  
Make sure  
lamp goes out and then release both buttons.  
TWIN  
PICTURE  
Q-SOUND  
DISPLAY  
VIEW  
MODE  
(3) Within ten seconds after releasing  
and  
, enter your VCR’s two-  
) (refer  
CH  
INPUT  
TITLE  
FF  
digit remote control code number using DIRECT ACCESS (  
to the list on page 65). The code should be identified within two minutes.  
VCR/  
TV  
~
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
•
lights for two seconds and then goes out. This indicates that the setting is  
VCR/DVD  
POWER  
DDFC  
performed successflly.  
• The remote control is now ready to send commands to your VCR.  
Some brands have more than one remote code listed, due to changes in the  
remote codes from early to later model years, or due to format differences  
(VHS/BETA). In such cases, you may have to try more than one code to find  
the code your VCR accepts.  
• Depending on the model, year produced, brand, and type of VCR, some models  
may not be compatible with the remote control.  
Note  
Tips on Identifying your VCR through the Search method  
DISPLAY  
(1) While pointing the front part of the remote control towards the infrared sensor of the VCR, press  
and then  
and hold them down for up to two minutes. Be careful not to let the VCR scan more than  
five channels when the indicator starts to increase. If you continue to hold down the buttons after five  
channel scans, the proper remote code can be passed up and the two-minute cycle will have to be  
repeated.  
• The remote control then searches in order for the VCR Brand Code Number (listed on page 65).  
DISPLAY  
(2) At the instant when the VCR channel changes, release  
and  
and the procedure will be  
completed. If a channel change does not occur on the VCR within two minutes, read the identifying  
instructions again and repeat the steps. Should a channel change still not occur, the remote will most  
likely not operate your VCR.  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation of the Remote Control for Other Devices (Continued)  
REMOTE CONTROL  
CODE NUMBER  
REMOTE CONTROL  
CODE NUMBER  
VCR BRAND  
VCR BRAND  
Multitech  
29  
Akai  
25, 26, 37  
NEC  
15, 22, 30  
04, 44  
05, 06  
04, 05  
04, 05, 08  
04  
Audio Dynamics  
Broksonic  
Canon  
15, 22, 30  
Panasonic  
Pentax  
Philco  
Philips  
Quasar  
RCA  
Realistic  
Samsung  
Scott  
Sears  
Sharp  
32  
04  
Capehart  
Craig  
Curtis Mathis  
Daewoo  
DBX  
Dynatech  
Emerson  
Fisher  
Funai  
GE  
Goldstar  
Hitachi  
Instant Replay  
JC Penney  
JVC  
Kenwood  
Lloyds  
Magnavox  
Magnin  
Marantz  
Memorex  
Minolta  
Mitsubishi  
Montgomery Ward  
34  
31  
04  
06, 07, 33  
01, 02, 24  
23, 31  
20  
06, 11, 24  
01, 02, 03  
36  
12, 13, 38  
29  
04, 05, 08  
29  
15  
15, 29  
27, 29  
29  
21  
19, 20  
30  
34  
15, 22, 30  
29  
21, 32, 35  
09, 11  
29  
Shintom  
Sony  
04  
24  
06  
Sound Design  
Sylvania  
Symphonic  
Tatung  
04  
04, 06, 24, 30  
15, 41, 42  
Teac  
15  
29  
Teknika  
Thomas  
TMK  
04, 05, 08  
31  
30  
04, 10, 24, 29  
06  
17, 18, 39, 40  
02, 43  
Toshiba  
Video Concepts  
Yamaha  
Zenith  
15, 29, 30  
16  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation of the Remote Control for Other Devices (Continued)  
How to Identify a DVD Player  
■ To Identify Your DVD player –Direct Entry Method  
Use the following steps and the list below to quickly find the remote control code  
for your DVD player.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
• First look up your DVD player’s remote code number on the list below before  
PERSONAL PREFERENCE  
continuing the direct code entry steps below.  
DVD/  
A
B
C
D
CATV  
(1) Press  
and the button lights.  
ENTER  
DISPLAY  
INPUT  
(2) While holding  
, press  
on your remote control.  
DVD/  
CATV  
VOL  
CH  
MENU  
AV MODE  
MUTE  
Make sure  
lamp goes out and then release both buttons.  
DISPLAY  
INPUT  
(3) Within ten seconds after releasing  
and  
, enter your DVD player’s  
) (refer to the list).  
two-digit code number using DIRECT ACCESS (  
The code should be identified within two minutes.  
~
INPUT  
ANT-A/B  
DVD/  
CATV  
DISPLAY  
•
lights for two seconds and then goes out. This indicates that the setting  
ENT. FLASHBACK  
is performed successflly.  
• The remote control is now ready to send commands to your DVD player.  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
• Depending on the model, year produced, brand, and type of DVD player, some  
INPUT  
TITLE  
FF  
models may not be compatible with the remote control.  
Note  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
REMOTE CONTROL  
DVD PLAYER BRAND  
VCR/DVD  
POWER  
CODE NUMBER  
DDFC  
JVC  
09  
06  
02  
08  
03  
07  
01  
05  
04  
Mitsubishi  
Panasonic  
Pioneer  
RCA  
Samsung  
Sharp  
Sony  
Toshiba  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation of the Remote Control for Other Devices (Continued)  
How to Identify a DTV STB (Digital TV Set-Top Box)  
■ To Identify Your DTV STB –Direct Entry Method  
Use the following steps and the list below to quickly find the remote control code  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
for your DTV STB.  
• First look up your DTV STB’s remote code number on the list below before  
continuing the direct code entry steps below.  
PERSONAL PREFERENCE  
DTV/  
STB  
A
B
C
D
(1) Press  
and the button lights.  
ENTER  
DISPLAY  
(2) While holding down  
, press  
on your remote control.  
DTV/  
STB  
VOL  
CH  
MENU  
AV MODE  
MUTE  
Make sure  
lamp goes out and then release both buttons.  
DISPLAY  
(3) Within ten seconds after releasing  
and  
, enter your DTV STB’s  
) (refer to the list).  
two-digit code number using DIRECT ACCESS (  
The code should be identified within two minutes.  
~
INPUT  
ANT-A/B  
DTV/  
STB  
DISPLAY  
•
lights for two seconds and then goes out. This indicates that the setting is  
ENT. FLASHBACK  
performed successflly.  
TWIN  
• The remote control is now ready to send commands to your DTV STB.  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
• Depending on the model, year produced, brand, and type of DTV STB, some  
models may not be compatible with the remote control.  
INPUT  
TITLE  
FF  
Note  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
Identifying your DTV STB through the Search method  
(1) While pointing the front part of the remote control towards the infrared sensor  
DISPLAY  
of the DTV STB, press  
and then  
and hold them down for up to  
two minutes. Be careful not to let the DTV STB scan more than five channels  
when the indicator starts to increase. If you continue to hold down the  
buttons after five channel scans, the proper remote code can be passed up  
and the two-minute cycle will have to be repeated.  
• The remote control then searches in order for the DTV STB Brand Code  
DISPLAY  
Number (listed below).  
(2) At the instant when the DTV STB channel changes, release  
and  
and the procedure will be completed. If a channel change does not occur on  
the DTV STB within two minutes, read the identifying instructions again and  
repeat the steps. Should a channel change still not occur, the remote will  
most likely not operate your DTV STB.  
REMOTE CONTROL  
DTV STB BRAND  
CODE NUMBER  
04  
01  
02  
01  
03  
Panasonic  
Pioneer  
RCA  
Sharp  
Sony  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation of the Remote Control for Other Devices (Continued)  
How to Identify a Cable Converter  
■ To Identify Your Cable Converter –Direct Entry Method  
Use the following steps and list (on page 69) to quickly find the remote control  
code for your cable TV converter.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
• First look up your converter’s remote code number on page 69 before  
PERSONAL PREFERENCE  
continuing the direct code entry steps below.  
DVD/  
A
B
C
D
CATV  
(1) Press  
and the button lights.  
ENTER  
DISPLAY  
(2) While holding down  
, press  
on your remote control.  
DVD/  
VOL  
CH  
CATV  
MENU  
AV MODE  
MUTE  
Make sure  
lamp goes out and then release both buttons.  
DISPLAY  
(3) Within ten seconds after releasing  
and  
, enter your converter’s  
) (refer to the list  
two-digit code number using DIRECT ACCESS (  
on page 69). The code should be identified within two minutes.  
~
INPUT  
ANT-A/B  
DVD/  
CATV  
DISPLAY  
•
lights for two seconds and then goes out. This indicates that the setting  
ENT. FLASHBACK  
is performed successfully.  
• The remote control is now ready to send commands to your converter.  
TWIN  
PICTURE  
Q-SOUND  
VIEW  
MODE  
CH  
• Depending on the model, year produced, brand, and type of CATV converter, some  
models may not be compatible with the remote control.  
Note  
INPUT  
TITLE  
FF  
REW  
CH/SKIP  
PAUSE  
STOP  
REC  
VCR/DVD  
POWER  
DDFC  
Identifying your Cable Converter through the Search  
method  
(1) While pointing the front part of the remote control towards the infrared sensor  
of the cable converter, press DISPLAY and then  
and hold them down for up  
to two minutes. Be careful not to let the cable converter scan more than five  
channels when the indicator starts to increase. If you continue to hold down  
the buttons after five channel scans, the proper remote code can be passed  
up and the two-minute cycle will have to be repeated.  
• The remote control then searches in order for the cable converter Brand  
DISPLAY  
Code Number (listed on page 69).  
(2) At the instant when the cable converter channel changes, release  
and  
and the procedure will be completed. If a channel change does not  
occur on the cable converter within two minutes, read the identifying  
instructions again and repeat the steps. Should a channel change still not  
occur, the remote will most likely not operate your cable converter.  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation of the Remote Control for Other Devices (Continued)  
CATV CONVERTER  
BRAND  
REMOTE CONTROL  
CODE NUMBER  
CATV CONVERTER  
BRAND  
REMOTE CONTROL  
CODE NUMBER  
Anvision  
07, 08  
Philips  
07, 08, 19, 26, 28, 29,  
Cable Star  
07, 08  
32, 33, 40, 41  
Eagle  
Eastern International  
General Instrument  
08  
02  
Pioneer  
Randtek  
RCA  
18, 20  
07, 08  
27  
04, 05, 15, 23, 24, 25,  
30, 36  
Regal  
12  
Hamlin  
Jerrold  
12, 13, 34  
04, 05, 15, 23, 24, 25  
30, 36  
37  
07, 08, 19, 25, 28, 29,  
32, 33, 40, 41  
09  
Regency  
Scientific Atlanta  
Sylvania  
Teknika  
Texscan  
Tocom  
02  
03, 22, 42  
11  
06  
11  
17, 21  
31  
Macom  
Magnavox  
NSC  
Unika  
Oak  
Oak Sigma  
Panasonic  
01, 16, 38  
18  
27, 39  
Viewstar  
07, 08, 19, 26, 28, 29  
32, 33, 40, 41  
14  
Zenith  
Specifications  
Model  
PV6111W  
Signal System  
Channel  
NTSC  
AIR 2ch – 69ch  
CATV 1ch – 125ch  
Antenna input  
Video input  
ANT A/B 75 Ω unbalance  
(INPUT 1, 2, 3, 4) Composite  
Input jack: Pin-jack × 1  
Input level: 1 Vp-p/75 Ω/negative sync  
S video input  
(INPUT 1, 2, 3) Y/C  
Y: 1 Vp-p/75 Ω/negative sync  
C: 0.286 Vp-p/75 Ω  
Component input  
(INPUT 4, 5) Component (Y, PB, PR)  
Input jack: Pin-jack × 3 (INPUT 4)  
Input signal: 480I, 480P, 720P, 1080I  
Y: 1Vp-p/75 Ω/negative sync  
PB, PR: 0.525 Vp-p/75 Ω  
(75 % saturation level)  
HD input  
(RGB)  
(INPUT 3) R, G, B, H, V  
INPUT jack: Dsub 15 pin × 1  
Input signal: 480P, 540P, 720P, 1080I  
RGB: 0.7 Vp-p/75 Ω/no sync  
HD, VD: TTL level/positive and negative  
AUDIO input  
(INPUT 1, 2, 3, 4, 5)  
Input jack: Pin-jack × 2  
0.5 Vrms/22 kΩ or over  
VAO  
Output jack: Pin-jack × 2  
(Variable audio output)  
0.89 Vrms (max)/2.2 kΩ  
Monitor Out  
Video: Composite Video 1 Vp-p/75 Ω/negative  
Audio: 500 mVrms (100% modulation/Less than 1 kΩ)  
Audio output  
30 W (15 W + 15 W)  
120 V AC, 60Hz  
290 W  
Power supply  
Power consumption  
Dimensions  
5621/32" (W) × 577/8" (H) × 2845/64" (D)  
[1439 mm (W) × 1470 mm (H) × 729 mm (D)]  
Weight  
298lbs (135.2 kg)  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Video and Audio Input Jacks  
■ Connecting video equipment for video playback  
• When the television is connected to video equipment as shown below, the material being played back on the  
video equipment can be seen on the television screen.  
Connecting a video device equipped with a video output terminal  
(Front terminals of Rear Projection TV)  
When noise or distortion appears on TV  
caused by connecting a video game  
machine, select the other setting of the  
DDFC mode (See page 58).  
IN 2  
L-AUDIO-R  
VIDEO EQUIPMENTS  
VIDEO  
S-VIDEO  
Signal  
To AUDIO OUTPUT  
To S-VIDEO OUTPUT  
To VIDEO OUTPUT  
or  
CAMCORDER  
TV GAME  
• The S-VIDEO INPUT terminals offer a higher quality image by accepting the image signal separated into color  
and brightness signals.  
• S-VIDEO INPUT terminals are for video signals only. The audio signals are connected to either IN 1 or IN 3  
AUDIO terminals (left and right).  
Note  
(Rear terminals of Rear Projection TV)  
To AUDIO  
OUTPUT (L/R)  
To VIDEO OUTPUT  
ANT/CABLE 75  
Video Equipment  
Signal  
ANT-A  
To AUDIO  
OUTPUT (L/R)  
OUT  
ANT-B  
(When your video equipment  
TO S-VIDEO OUTPUT  
has an S-VIDEO output terminal).  
R AUDIO L VIDEO  
MONITOR OUT  
(EXCEPT FOR HD AND  
COMPONENT SIGNALS)  
Signal  
IN 1  
IN 3  
CENTER  
OUT  
Signal  
S-VIDEO  
Signal  
To AUDIO OUTPUT (L)  
To AUDIO OUTPUT (R)  
IN 1  
IN 3  
To VIDEO OUTPUT  
COMPONENT  
Color Difference  
Output Jack (Component )  
Y
P
B
PR  
Signal  
Signal  
IN 4  
IN 5  
HD INPUT IN 3  
(USE FOR HDTV SIGNAL ONLY)  
To AUDIO OUTPUT (L)  
To AUDIO OUTPUT (R)  
R AUDIO L VIDEO  
VAO  
CENTER IN  
R AUDIO L  
To HD INPUT  
(To output terminals of DTV)  
Fasten with the screws  
located at both ends.  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Video and Audio Input Jacks  
(Continued)  
■ Video playback  
INPUT  
• Press the remote’s  
to select the VIDEO INPUT mode to which the video equipment you want to play  
back is connected.  
INPUT  
• The external VIDEO INPUT mode will change as follows each time  
is pressed.  
AIR  
or  
CABLE  
INPUT 1  
(VIDEO)  
Rear  
INPUT 2  
(VIDEO) (VIDEO/HD INPUT) (VIDEO/HD/DVD)  
Front Rear Rear  
INPUT 3  
INPUT 4  
INPUT 5  
(DTV)  
Rear  
• You can select INPUT mode by pressing  
when the TV is set to the highest channel stored in memory, or  
by pressing  
when it is set to the lowest channel.  
• When connecting video or audio equipment to the television, be sure that the power is turned off in order to prevent  
damage to either the television or the equipment being connected.  
• An S-VIDEO terminal has priority over its corresponding VIDEO terminal. When you want to watch pictures from  
video equipment connected to a VIDEO terminal, unplug equipment connected to the corresponding S-VIDEO  
terminal.  
Note  
• It is the intent of Marantz that this product be used in full compliance with the copyright laws of the United States  
and that prior permission be obtained from copyright owners whenever necessary.  
• For detailed information on the connection and use of auxiliary equipment, refer to the instruction manuals of the  
equipment being used.  
• Connection cables can be obtained from your local video store.  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Audio Output Jacks  
These jacks are used for connecting a standard studio amplifier. Control of STEREO/MONO/SAP, BASS,  
TREBLE, BALANCE, VOLUME and MUTE is retained at the Rear Projection TV. These jacks relay the audio  
signals of all programs being displayed on the Rear Projection TV screen.  
R AUDIO L VIDEO  
MONITOR OUT  
(EXCEPT FOR HD AND  
COMPONENT SIGNALS)  
IN 1  
IN 3  
S-VIDEO  
IN 1  
IN 3  
COMPONENT  
Y
P
B
PR  
IN 4  
IN 5  
R AUDIO L VIDEO  
VAO  
CENTER IN  
R AUDIO L  
or  
VAO AUDIO OUTPUT  
AUDIO OUTPUT  
To the audio  
input terminals  
Stereo amplifier  
Speaker System  
(1) Before connecting the cable, turn on the Rear Projection TV and adjust the VOLUME control on the TV for a  
moderate listening level.  
(2) Turn off the Rear Projection TV and connect the audio cord to the AUDIO OUTPUT or VAO AUDIO out  
JACKS on the Rear Projection TV.  
(3) Turn the Rear Projection TV and stereo amplifier on.  
(4) To change SPEAKER settings, see page 29. To check SPEAKER connections, see page 70.  
(5) Adjust the VOLUME control on the stereo amplifier as desired.  
(6) Control of the audio can be done using the audio controls (STEREO/MONO/SAP, VOLUME, EQUISOUND  
and MUTE), from either the remote control, or directly from the Rear Projection TV.  
• For detailed information on the connection and use of auxiliary equipment, refer to the operation  
manuals of the equipment being used.  
• When connecting monaural equipment to the AUDIO INPUT or OUTPUT of this set, use an audio  
connection cable and plug adapter as shown below.  
• When using VAO terminals, for optimal sound quality, it is recommended to keep the Rear Projection  
TV’s audio output level high.  
<Not supplied>  
Plug adapter  
To the Rear  
Projection TV  
To the equipment  
being connected  
Pin plug x2  
Pin plug  
Pin jack / Mini plug  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Calling for Service  
Check these items and see if you can correct a problem with a slight adjustment of the controls.  
QUICK SERVICE CHECK LIST  
POSSIBLE REMEDY  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Try a new channel, if OK, then possible station trouble.  
Is Rear Projection TV plugged in? Power at outlet?  
Is Rear Projection TV’s POWER button on?  
Is antenna connected to terminal on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference or external electrical noise.  
Turn off with POWER button and then turn it on after  
about a minute.  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Adjust COLOR control.  
Adjust PICTURE control.  
Check external Video/Audio products; look for loose / broken  
connections cables. (Refer to page 70.)  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Check the batteries of Remote Control.  
Are audio cables connected firmly? Check the volume level.  
Is SP ON? See page 29.  
Change Closed Caption mode to “OFF” / Energy Save  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
mode to “OFF”.  
Unplug the Rear Projection TV and plug it in again after 2 minutes.  
• When viewing in TEXT mode, if no TEXT broadcast is being received, the screen may  
become dark and blank. Should this occur, set the Closed Caption mode to “OFF”.  
• If your TV does not work normally in case of a power failure, turn the power off and then  
Note  
turn the power on again.  
(Dark and Blank Picture)  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Unidad Principal  
Sección de control delantera  
POWER (potencia)  
Pulsar → On.  
Pulsar de nuevo → Off.  
POWER  
POWER  
VIEW  
Área sensor para  
el control remoto  
Para abrir la cubierta  
R
E
W
O
P
W
IE  
V
R
E
W
O
P
DETRÁS DE LA CUBIERTA  
Entrada AUDIO  
L/R (I/D)  
Botón ENTER  
IN 2  
L-AUDIO-R  
MENU  
ENTER  
(Los otros terminales están  
ubicados en la parte trasera.)  
Botón MENU (Menú)  
Pulse el botón MENU (Menú)  
para acceder a la pantalla del  
MAIN MENU (Menú Principal)  
VOL  
CH  
Entrada S-VIDEO  
Entrada VIDEO  
VIDEO  
S-VIDEO  
Botones de volumen VOL (+)/(–)  
(+) Aumenta el sonido  
(–) Disminuye el sonido  
Botones CH (canal) (arriba)/(abajo)  
(
(
)
)
Selecciona el próximo canal más alto así como también VIDEO INPUT.  
Selecciona el próximo canal más bajo así como también VIDEO INPUT.  
• Si el televisor de retroproyección no es usado por un largo período de tiempo, desactive la alimentación de la unidad  
principal para evitar que el televisor de retroproyección falle en su funcionamiento (por ej. si TV POWER se ajusta a  
ON durante un corte de luz, el estado del televisor de retroproyección antes del corte, TV POWER cambia a ON  
cuando se restaura la alimentación).  
Nota  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Funciones Básicas del Control Remoto  
Este control remoto puede usarse para operar el televisor de retroproyección, una videograbadora, un  
decodificador DTV STB, un reproductor de video DVD y un convertidor de cable TV. Los botones que pueden  
usarse varian de acuerdo al dispositivo conectado. Para los detalles, refiérase a la página siguiente.  
Ventana del transmisor infrarrojo  
Botones de selección del modo del control remoto  
Se utiliza para cambiar los modos de la unidad del  
control remoto.  
POWER (alimentación)  
Pulsar → On.  
•
Seleccionando uno de los tres botones de selección de  
modo, este control remoto se puede utilizar para ajustar  
funciones comunes, tales como selección de canal, para  
ese dispositivo.  
Pulsar de nuevo → Off (Stand-by).  
Botones PERSONAL PREFERENCE  
(preferencia personal)  
•
Utilizado para seleccionar cualquiera de los cuatro canales  
preajustados.  
Botón ENTER (introducir)  
MENU (menú)  
Botones del cursor  
Utilizados para mover el cursor en la pantalla del menú  
Pulsar → Acceso al MAIN MENU (Menú principal)  
Pulsar de nuevo → Sale del MAIN MENU  
(Menú principal)  
VOLUME UP/DOWN (volumen arriba/abajo)  
(+) Aumenta el sonido.  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
(–) Disminuye el sonido.  
PERSONAL PREFERENCE  
CHANNEL UP/DOWN (canal arriba/abajo)  
(+) Selecciona el próximo canal más alto.  
(–) Selecciona el próximo canal más bajo.  
AV MODE (Modo AV)  
A
B
C
D
MUTE (enmudecer)  
Pulsar → Enmudece el sonido.  
Pulsar de nuevo → Restablece el sonido.  
• CLOSED CAPTION aparece automáticamente  
cuando el sonido es silenciado.  
INPUT (entrada)  
ENTER  
Pulsar  
→
Cambiar al modo INPUT 1 del vídeo  
externo.  
VOL  
CH  
Pulsar de nuevo  
→
Cambiar al modo INPUT 2  
del vídeo externo.  
MENU  
AV MODE  
MUTE  
Siempre y cuando la transmisión tenga esta señal.  
Pulsar 3 veces  
Pulsar 4 veces  
Pulsar 5 veces  
Pulsar 6 veces  
→
Cambiar al modo INPUT 3  
del vídeo externo.  
Cambiar al modo INPUT 4  
del vídeo externo.  
Cambiar al modo INPUT 5  
del vídeo externo.  
Volver a cambiar al modo TV  
inicial.  
DIRECT ACCESS (acceso directo)  
Accede cualquier canal mediante el teclado.  
→
→
→
Botón  
: Solo para el Decodificador DTV  
INPUT  
ANT-A/B  
DISPLAY  
FUNCIÓN POP  
Puede usted observar dos imágenes al mismo tiempo.  
ENT. FLASHBACK  
- CH -  
:
Utilizado para cambiar el canal para  
la sub imagen de la pantalla TWIN  
PICTURE (imagen doble).  
Se usa para seleccionar la fuente de  
entrada para la imagen secundaria de  
la pantalla TWIN PICTURE.  
Botón ANT-A/B  
Pulsar para cambiar entre ANTENNA-A (antena-A)  
y ANTENNA-B (antena-B) cuando desee ver el TV.  
(canal)  
INPUT:  
(entrada)  
DISPLAY (visualizar)  
Pulsar → Muestra el canal recibido durante 4  
TWIN PICTURE: Divide la pantalla en dos pantallas de  
(imagen doble)  
segundos.  
tamaño iguales más pequeños. Cuando  
se presiona de nuevo, amplí  
izquierda, y si se presiona de nuevo,  
se sale de la función.  
Pulsar para seleccionar el modo de la  
pantalla SEARCH (buscar).  
Selecciona la pantalla en los modos de  
pantalla de búsqueda y TWIN PICTURE.  
Cuando se pulsa este botón con la  
pantalla regular, se cambia a la pantalla  
TWIN PICTURE (imagen doble) y la  
imagen en el momento en el que se pulsó  
el botón será la sub imagen, visualizada  
como una imagen congelada.  
Pulsar de nuevo → Muestra el tiempo restante  
de SLEEP TIMER (temporizador de  
estado dormir) y VIEW TIMER  
(temporizador de vista) durante 4  
segundos.  
FLASHBACK (retorno)  
Vuelve al canal previamente visualizado.  
ENT. (Intro.)  
Utilizado en algunos casos donde un VCR o  
una Caja Convertidor a para cables necesita  
una orden de “enter” después de seleccionar  
canales, al utilizar el botón DIRECT  
ACCESS.(acceso directo)  
DDFC  
POWER  
SEARCH:  
(buscar)  
SELECT:  
(seleccionar)  
FREEZE:  
(congelar)  
Q-SOUND  
Controla los ajustes del sonido envolvente.  
SWAP:  
(cambio)  
Las pantallas izquierda y derecha se  
intercambian con la función TWIN  
PICTURE (imagen doble).  
VIEW MODE (Modo vista)  
Seleccione el tamaño de la vista.  
CM SKIP:  
(saltar  
comerciales)  
Utilice esta función cuando desea  
escanear otros canales durante una  
pausa comercial.  
LIGHT (luz)  
Área de control del VCR/DVD/DTV  
Cuando se pulsa este botón, algunos de los botones en el  
DDFC  
Utilizado para seleccionar imagen de alta calidad.  
control remoto se iluminarán. La luz se apagará si no se lleva a  
cabo ninguna operación dentro de seis segundos. Este botón se  
utiliza para llevar a cabo operaciones en lugares oscuros.  
• El botón de iluminación en el control remoto se ilumina en la oscuridad. Para usar la visualización de iluminación en la  
oscuridad en el control remoto coloquelo bajo una luz fluorescente u otra iluminación.  
• El material fosforescente no contiene material radioactivo o tóxico, su uso por lo tanto es seguro.  
• El grado de iluminación variará dependiendo en la fuerza de la luz utilizada.  
Nota  
• El grado de iluminación disminuirá con el tiempo y dependiendo en la temperatura.  
• El tiempo que se necesita para cargar la visualización fluorescente varía dependiendo en la luz alrededor.  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Antes de llamar al Servicio de Reparaciones  
Verifique los siguientes puntos para ver si puede solucionar el problema.  
LISTA DE COMPROBACIONES  
DE SERVICIO RAPIDO  
POSIBLE SOLUCIÓN  
Pruebe con otro canal y si todo está bien, el problema  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
puede ser de la emisora.  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
¿Está conectado el televisor de retroproyección? Llega electricidad al tomacorrientes?  
¿Está conectado el interruptor del televisor de retroproyección?  
¿
Está conectado la antena al terminal del panel posterior  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
del televisor?  
Si utiliza una antena exterior, asegurese de que el cable no  
esté dañado.  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Compruebe si hay interferencia local.  
Desconecte el interruptor POWER y vuelva a conectarlo  
después de transcurrir un minuto.  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Adjuste el control de COLOR.  
Adjuste el control de MATIZ.  
Verifique los productos externos de Video/Audio, revise  
si hay gufas de conexiones sueltas o rotas.  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Compruebe el estado de las pilas del control remoto.  
Están bien conectados los cables de sonido? Compruebe  
el nivel del volumen.  
¿
Está la función SP en ON (activada)?  
Desactive (OFF) el modo CLOSED CAPTION / Desactive  
(OFF) el modo Ahorro de Energía (Energy Save).  
Desenchufe el televisor de retroproyección y vuelva a  
enchufarlo despúes de dos minutos.  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
• Cuando se ve en modo TEXTO sin recibir emisiones de TEXTO, la pantalla puede  
ponerse en blanco y negro. Si ocurriera ésto, ponga el modo CLOSED CAPTION en OFF.  
• Si su televisor no funciona normalmente en caso de corte de energía eléctrica, apague el  
televisor y vuelva a encenderlo otra vez.  
Nota  
(Imagen oscura y en blanco)  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Unité Principale  
Commandes avant  
POWER (Alimentation)  
Appuyez une fois sur cette touche → Marche  
Appuyez à nouveau sur cette touche → Arrêt  
POWER  
POWER  
VIEW  
ZONE DU CAPTEUR  
DE TELECOMMANDE  
Pour ouvrir le couvercle  
R
E
W
O
P
W
IE  
V
R
E
W
O
P
Derrière le couvercle  
Entrée AUDIO L/R  
(audio gauche/droite)  
Touche ENTER(Entrée)  
IN 2  
L-AUDIO-R  
MENU  
ENTER  
(D’autres bornes se  
trouvent à l’arrière.)  
Touche MENU  
Appuyez sur cette touche  
pour accéder à la page de  
menu principal (MAIN MENU).  
VOL  
CH  
Entrée S-VIDEO  
Entrée VIDEO  
VIDEO  
S-VIDEO  
Touches de volume VOL (+) (–) Touches CH (haut)/(bas)  
(+) Augmente le volume  
(–) Diminue le volume  
(
) Sélectionne la chaîne supérieure suivante ainsi que  
VIDEO INPUT (Entrée vidéo).  
(
) Sélectionne la chaîne inférieure suivante ainsi que  
VIDEO INPUT (Entrée vidéo).  
• Si le téléviseur à rétroprojection n’est pas utilisé pendant longtemps ou lors d’une panne de courant, réglez la  
touche POWER de l’unité principale sur Arrêt (OFF) pour éviter un mauvais fonctionnement du téléviseur. (Par  
exemple, si la touche POWER du téléviseur est réglée sur Marche (ON) pendant une panne de courant, le  
téléviseur à rétroprojection reste dans l’état d’avant la panne de courant et le téléviseur est mis sous tension (ON)  
lorsque le courant est rétabli.  
Remarque  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fonctions de Base de la Télécommande  
Cette télécommande peut être utilisée pour faire fonctionner le téléviseur à rétroprojection, un  
magnétoscope, un décodeur DTV STB, un lecteur vidéo DVD et un convertisseur de télévision par câble.  
Les touches utilisables varient selon l’appareil utilisé. Consultez la page suivante pour les détails.  
CAPTEUR INFRA-ROUGE  
Touches de sélection de mode de la télécommande  
S’utilisent pour commuter entre les modes de  
fonctionnement de la télécommande.  
POWER (Alimentation)  
Une pression sur cette touche → Marche.  
•
En sélectionnant une de ces trois touches de sélection de  
mode, cette télécommande peut être utilisée pour effectuer l  
es commandes courantes telles que la sélection de chaînes  
d’un autre appareil.  
Nouvelle pression sur cette touche → Arrêt (Stand-by).  
Touches PERSONAL PREFERENCE  
(Préférences personnelles)  
•
S’utilisent pour sélectionner un des quatre  
canaux préréglés.  
Touche ENTER (Entrée)  
MENU  
Touches du curseur  
S’utilisent pour déplacer le curseur sur l’écran  
de menu.  
Une pression sur cette touche →  
Accès au menu principal  
Nouvelle pression sur cette touche →  
Sortie du menu principal  
DTV  
STB  
VCR/  
TV  
DVD/  
CATV  
POWER  
PERSONAL PREFERENCE  
VOLUME (+) et (–)  
(+) Augmente le volume  
(–) Diminue le volume  
A
B
C
D
CHANNEL UP/DOWN (+)(–)  
(touches de chaînes)  
Mode AV  
ENTER  
(+) Sélectionne la chaîne supérieure  
(–) Sélectionne la chaîne inférieure  
MUTE (mise en sourdine)  
Une pression sur cette touche →  
Mise en sourdine.  
VOL  
CH  
INPUT (Entrées)  
MENU  
AV MODE  
MUTE  
Une pression sur cette touche  
→
Commutation  
en mode Entrée vidéo 1 externe.  
Nouvelle pression sur cette touche →  
Nouvelle pression  
→
Commutation en mode  
Entrée vidéo 2 externe.  
Reprise du niveau volume original.  
•
CLOSED CAPTION apparaît lorsque le  
son est mis en sourdine.  
INPUT  
ANT-A/B  
3ème pression  
4ème pression  
5ème pression  
→
→
→
Commutation en mode Entrée  
vidéo 3 externe.  
Commutation en mode Entrée  
vidéo 4 externe.  
Commutation en mode Entrée  
vidéo 5 externe.  
DIRECT ACCESS (accès direct)  
Accès direct aux chaînes numéros  
DISPLAY  
Touche  
: Unique décodeur DTV  
ENT. FLASHBACK  
FONCTION POP  
Vous pouvez regarder deux émissions à la fois  
6ème pression → Reprise du mode vidéo original.  
S’utilise pour commuter la chaîne de  
l’image secondaire de l’écran à double  
image.  
- CH -  
:
Touche ANT-A/B  
Appuyez sur cette touche pour commuter entre  
les antennes de télévision A et B.  
INPUT:  
(Entrée)  
S’utilise pour sélectionner la source  
d’entrée de l’image secondaire sur  
l’écran à double image.  
Une pression divise l’écran en deux  
sections d’égale grandeur. Une nouvelle  
pression agrandit l’écran de gauche,  
tandis que la pression suivante permet  
d’abandonner cette fonction.  
DISPLAY (commande d’affichage)  
Une pression sur cette touche → Affichage de la  
chaîne en cours de réception pendant 4  
secondes.  
Nouvelle pression → Affichage du temps restant  
des temporisation de mise hors service SLEEP  
TIMER et VIEW TIMER pendant 4 secondes.  
DDFC  
POWER  
TWIN PICTURE :  
(Double image)  
SEARCH:  
(Recherche)  
SELECT:  
Appuyez sur cette touche pour  
FLASHBACK  
sélectionner le mode écran de recherche.  
Sélectionne l’écran en mode Double  
image et Recherche.  
Retourne sur la chaîne regardée précédemment.  
ENT.  
(Sélection)  
Utilisé dans le cas où un magnétoscope ou un  
boîtier de conversion de câble nécessite  
‘l’entrée’ d’une commande après la sélection de  
chaîne quand la touche d’accès direct DIRECT  
ACCESS est utilisée.  
FREEZE:  
(Image gelée)  
Lorsque l’on appuie sur cette touche en  
écran normal, ce dernier passe en mode  
Double image, l’image à l’écran à ce  
moment là devient l’image secondaire et  
s’affiche sous une forme gelée.  
Les écrans gauche et droit sont  
intervertis avec la fonction Double image  
(TWIN PICTURE).  
Q-SOUND  
Pour les réglages des sons “surround”.  
SWAP:  
(Intervertir)  
VIEW MODE  
Sélectionne le format de l’image.  
CM SKIP:  
(Saut Pub)  
Permet d’explorer les autres chaînes  
pendant une interruption publicitaire.  
VCR/DVD/DTV CONTROL  
(commande de magnétoscope/VCR/DVD/DTV)  
LIGHT (lumière)  
Lorsque l’on appuie sur cette touche, certaines touches de la  
télécommande s’illuminent. Cet éclairage s’éteint au bout de 6  
secondes d’inactivité. Cette touche s’utilise lorsque l’éclairage  
est insuffisant.  
DDFC  
S’utilise pour passer en mode image de haute qualité.  
• Les touches claires sur la télécommande luisent dans l’obscurité. Pour utiliser l’éclairage phosphorescent de la  
télécommande, placez celle-ci sous une lampe fluorescente ou un autre éclairage.  
• Les matériaux phosphorescent employés ne contiennent pas de produit radioactif ou toxique et cette télécommande peut  
être utilisée sans crainte.  
Remarque  
• Le degré d’illumination dépend de l’intensité de la source de lumière utilisée.  
• Le degré d’illumination diminue dans le temps en fonction aussi de la température.  
• Le temps de rechargement de l’affichage phosphorescent varie suivant la source de lumière.  
78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Avant de faire appel au Service Après-vente  
Vérifiez les points suivants pour voir s’il n’est pas possible de résoudre le problème par un simple ajustement des commandes.  
LISTE DE VÉRIFICATION RAPIDE  
CORRECTION POSSIBLE  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Essayer une autre chaîne. Si normal, panne possible de station.  
XX  
X
Le téléviseur à rétroprojection est-il branché? Prise secteur  
sous tension?  
X
X
La touche POWER du téléviseur à rétroprojection est-elle allumée?  
L’antenne est-elle branchée sur la borne à l’arrière de l’appareil?  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Si une antenne extérieure est utilisée, s’assurer que son fil  
n’est pas cassé.  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Vérifier la présence d’interférences locales ou de bruits  
électriques externes.  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Mettre hors tension par la touche POWER et remettre sous  
tension après une minute environ.  
Ajuster la commande COLOR.  
Ajuster la commande PICTURE.  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Vérifier les dispositifs audio/vidéo externes. S’assurer que les  
fils de branchement ne sont pas détachés ou cassés.  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Vérifier les piles de la télécommande.  
Les cordons audio sont-ils fermement branchés? Vérifier le  
niveau du volume.  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
La touche SP est-elle sur ON?  
Changer le mode Closed Caption à “OFF” / mode Economie  
d’énergie à “OFF”.  
Débrancher le téléviseur à rétroprojection et le rebrancher  
2 minutes plus tard.  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
• A l’emploi du mode TEXTE, si une émission TEXTE n’est pas reçue, l’écran peut devenir  
sombre ou vierge. Dans ce cas, désactivez (OFF) le mode Closed Caption.  
• Si le téléviseur ne fonctionne pas normalement après une panne de courant, mettez-le  
hors tension, puis à nouveau sous tension.  
Remarque  
(Image en noir et blanc)  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIMENSIONS FOR INSTALLATION  
56.00" (1422)  
48.07" (1221)  
44.88" (1140)  
56.1" (1425)  
28.89" (734)  
13.86" (352)  
1.89" (48)  
53.62" (1362)  
0.75" (19)  
25.47" (647)  
52.32" (1329)  
PV6111W  
DIMENSIONS SHOWN AS  
INCHES (MM)  
80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Limited Warranty for the Marantz Rear Projection Television  
Who is covered?  
You must have proof of purchase to receive warranty service.  
What is covered?  
1) Warranty coverage begins the day you purchase your Rear Projection Television, and contintues  
for a period of one year.  
2) Marantz America will incur all labor charges for repairs during the warranty period.  
3) MarantzAmerica will incur all freight charges for warranty repairs, both to Marantz and the return  
to the customer.  
We suggest keeping all packing materials for any shipping that might be required.  
4) All parts, including repaired and replaced parts are covered only for the original warranty period.  
When the warranty on the product expires, the warranty on all replaced and repaired parts also  
expires.  
What is excluded?  
Your warranty does not cover:  
1) Labor charges for installation or setup of the product, cleaning, adjustment of customer controls  
on the product, and installation or repair of antenna systems outside of the product.  
2) Improper installation, removal or maintenance, or failure to follow instructions supplied with the  
product.  
3) Reception problems caused by signal conditions from cable or antenna systems outside the  
product.  
4) Burn in and or phosphor damage, due to the display of still images.  
5) Repair, attempted repair or modification performed by anyone other than an authorized Marantz  
America service center.  
6) Any product, on which the serial number has been defaced, modified or removed.  
7) Warranty is void if purchase was made from anyone other than an authorized Marantz  
dealer.  
8) Warranty is void if purchased from outside The United States of America or Canada.  
9) Warranty only valid in the United States of America and Canada.  
10) Damage due to lightning or power line surges, spikes and brown outs, damages that occur  
during shipping or transit, or damage which is attributed to acts of God.  
11) Incidental or consequential damages resulting from the product. (Some states do not allow the  
exclusion of incidental or consequential damages, so the above exclusion may not apply to  
you. This warranty gives you specific legal rights, and you may also have other rights that vary  
from state to state.)  
12) Commercial or institutional use.  
13) Any other causes which does not relate to product defect.  
Before requesting service:  
Please check your owner’s manual before requesting service. Adjustments of the controls and  
hook up guidelines discussed there may save you a service call.  
To get warranty service:  
Repair must be performed by an authorized service center. If you do not know of a Marantz  
authorized Television service center, contact your dealer. If your dealer is an authorized service  
center, they will arrange for repair. If your dealer is not a Marantz authorized Television service  
center, they will direct you to an authorized service center.  
Printed in U.S.A.  
TINS-7586MEZZ  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Kustom Musical Instrument Amplifier KG1 User Manual
Lanier Copier LD225 User Manual
Lenovo Blu ray Player 10086 User Manual
Lenovo Computer Hardware 4466 User Manual
LG Electronics Cell Phone AX4270 User Manual
Life Fitness Treadmill 9500HRT User Manual
Lightolier Work Light 24MHT45RS User Manual
Linksys Network Card WPC54A User Manual
Makita Cordless Drill 6075D User Manual
Midland Radio Portable Radio SP 400 User Manual