FRANÇAIS
ENGLISH
8 Channel Power Amplifier
MM8003
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
INTRODUCTION
CONTENTS
Thank you very much for purchasing this model MM8003 8-Channel Power Amplifier from Marantz.
This remarkable component has been engineered to provide you with many years of home theater enjoyment.
Please take a few minutes to read this manual thoroughly before you connect and operate the MM8003.
As there are a number of connection and configuration options, you are encouraged to discuss your own
particular home theater setup with your Marantz A/V specialist dealer.
INTRODUCTION ....................................1 OPERATION...........................................8
ACCESSORIES CHECK....................................................1
CONTENTS ............................................1
FEATURES.............................................2
BEFORE USE.........................................2
TURNING ON THE POWER..............................................8
TURNING THE POWER OFF............................................8
ADVANCED CONNECTIONS................9
BI-AMPLIFIER CONNECTIONS........................................9
MULTI ZONE SPEAKER CONNECTIONS......................10
MULTI ZONE CONNECTIONS........................................11
REMOTE CONTROL CONNECTIONS ...........................12
CONNECTIONS WITH EXTERNAL CONTROL
ACCESSORIES CHECK
NAMES AND FUNCTION ......................3
FRONT PANEL...................................................................3
REAR PANEL .....................................................................3
Before use, check the below accessories were
included in the package.
BASIC CONNECTIONS.........................4
PREPARING THE CONNECTION CABLES ....................4
INPUT CONNECTOR SWITCHING...................................4
AV8003 CONNECTIONS ...................................................5
SPEAKER CONNECTIONS...............................................6
POWER CABLE CONNECTION........................................7
USING AC OUTLETS.........................................................7
COMPONENTS................................................................12
AC power cable
TROUBLESHOOTING .........................13
RESETTING THE AMPLIFIER.........................................13
OTHERS ...............................................14
SPECIFICATIONS............................................................14
Remote control cable
User Guide
Warranty Card
USA × 1
Canada × 1
1
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
FEATURES
BEFORE USE
High-sound-quality design based on the pure
surround concept
This 8-channel power amplifier comes with upgraded
functions and supports the latest format of surround
sound without compromising the design technology
of Marantz's flagship models.
This section must be read before any connection is
made to the mains supply.
Left
8 inchs (0.2 m)
or more
Right
8 inchs (0.2 m) or
more
Above
8 inchs (0.2 m)
or more
A chimney-type heat sink and extremely quiet
cooling fan deal with the heat that is discharged
from the 8-channel amplifier to a high degree of
efficiency. A high-precision temperature sensor IC
is used to adjust the rotational speed of the cooling
fan in response to the changes in the amount of heat
generated by the amplifier.
Thesefeaturestogethermakeforlavishspecifications
well suited to the amplifier's use in high-end theater
systems, which are engineered to ensure virtually
noiseless operation.
The amplifier's chassis is copper-plated to protect
the analog audio circuitry from high-frequency
noise. This is an important technological aspect
for reproducing sound without compromising the
delicately nuanced sound fields of Super Audio.
In addition, top-of-the-line audio capacitors, film
capacitors and other high-quality components are
used to achieve a high-sound-quality design.
EQUIPMENT MAINS WORKING SETTING
8CH POWER AMPLIFIER MM8003
Your Marantz product has been prepared to comply
with the household power and safety requirements
that exist in your area.
Current feedback type of discrete power amplifier
with high sound quality
S
TANDBY
P
OWER
ON/OFF
The MM8003 features in all 8 channels the current
feedback type of power amplifier, which uses the
complementary push-pull circuitry incorporated
in Marantz's SM-11S1 Hi-Fi Power Amplifier.
This improves the model's operating stability and
enables it to achieve high-density, high-speed sound
reproduction across a wide sound range.
In the rear section the power amplifier is a current/
voltage conversion amplifier unit that employs a
Wilson current mirror circuit for amplifying sound up
to the treble range at low distortion levels.
MM8003 can be powered by 120V AC only.
Rear
8 inchs (0.2 m) or
more
COPYRIGHT
Recording and playback of any material may
require consent. For further information refer to the
following:
— Copyright Act 1956
— Dramatic and Musical Performers Act 1958
— Performers Protection Acts 1963 and 1972
— Any subsequent statutory enactments and
orders
Improved instantaneous current supply
capability
In the rear section of the power amplifier is the
LAPT (high-performance power transistor), which is
featured in Marantz's model SM-11S1 Hi-Fi Power
Amplifier. This device improves the instantaneous
current supply capability.
DO NOT LOCATE IN THE FOLLOWING PLACES
BALANCED/UNBALANCED switching function
This function makes it possible to select BALANCED
or UNBALANCED input each channel depending on
the application.
KEEP OBJECTS OFF
To ensure long-lasting use, do not locate the unit
where:
• Exposed to direct sunlight.
Keep objects off the unit. Blocking the vent can result
in accident and damage.
• Near to sources of heat such as heaters.
• Highly humid or poorly ventilated.
• Dusty.
Copper bus bars are featured in the unit that supplies
the power to each channel.
Remote power control
DO NOT TOUCH HOT SPOTS DURING AND
IMMEDIATELY AFTER USE
By connecting the amplifier to Marantz's model
AV8003 AV pre-tuner, the amplifier's power can be
switched on or off in tandem with the power on/off
operation of the AV8003 using the remote power
control function.
A floating ground connection that doesn’t form a
ground loop is used for the connection with the
AV8003 so the sound quality is not adversely
affected.
The power supply unit has a large toroidal transformer
that delivers low levels of noise and leakage flux
thanks to its internal structural features such as its
laminated core, silicon steel-plated core ring,etc.,
and the use of its shielded casing.
Original Marantz parts with a combined capacitance
of 100,000 µF (50,000µF/71V × 2), which have been
specially crafted to achieve the maximum in terms of
sound quality, are employed in the block capacitor, a
key component of the power supply unit.
During and immediately after use, the unit is hot
in areas other than the controls and rear panel
connection jacks. Do not touch hot spots and
especially the top panel. Contact with hot areas can
cause burns.
• Subjected to mechanical vibrations.
• On wobbly, inclined or otherwise unstable
surfaces
• Radiated heat is blocked such as in cramped
audio racks.
To ensure proper heat radiation, ensure the below
clearance from walls and other equipment.
Thanks to the improvements in the current supply
capability of these parts, you can enjoy high-powered
sound brimming with ambiance.
Other functions
Also provided are an IR flasher input connector to
support customized installation, and DC trigger input
connector and output connectors.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
NAMES AND FUNCTION
For a more detailed description of the functions of each part, refer to the pages given in ( ).
FRONT PANEL
REAR PANEL
q w
c v bn m ,
.
8CH POWER AMPLIFIER MM8003
CHANNEL 8
)
CHANNEL 7
(
CHANNEL 6
)
CHANNEL 5
(
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
)
CHANNEL 1 UNBALANCED
)
(
)
(
)
(
(
(
(
L
OPTION
C
SBR
SBL
SR
SL
R
OUT IN
OUT
IN
AC OUTLET
120V 60Hz
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALAANCED
BALANCED
UNBALANCED
BALANCED
FLASHER
IN
DC CONTROL REMOTE CONTROL
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
BALANCED
2
1
3
1
3
GND HOT
2
(+)
(
-
)
COLD
CONNECTION
UNSWITCHEDD 1.255AA 150W
AC IN
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
(
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
)
CHANNEL 1 SPEAKER SYSTEMS
6-8 OHMS
(
(
(
)
(
(
(
( )
L
OPTION
C
SBR
SBL
SR
SL
R
STANDBY
POWER ON/STANDBY
MODEL NO. MM8003
e
z x
q
w
e
POWER ON/STANDBY button (page 8)
STANDBY indicator (page 8)
Illumination lamp (page 8)
z
x
c
v
b
n
m
,
.
UNBALANCED (RCA) input connectors (page 5)
BALANCED (XLR) input connectors (page 5)
Input selector switches (page 4)
SPEAKER SYSTEMS output connectors (page 6)
Flasher input connector (page 12)
DC CONTROL IN/OUT connectors (page 12)
REMOTE CONTROL IN, OUT connectors (page 12)
AC IN socket (page 7)
AC OUTLET (page 7)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
BASIC CONNECTIONS
UNBALANCED CONNECTIONS
PREPARING THE CONNECTION CABLES
INPUT CONNECTOR SWITCHING
RCA audio cable
Provide the cables required by the component to
be used.
A BALANCED or UNBALANCED input for the input connectors can be selected for each channel.
Input selector switches
BALANCED CONNECTIONS
REMOTE CONTROL CONNECTIONS
XLR audio cable
RCA cable (accessory)
(This cable is required to connect the AV8003 or
other Marantz component to this amplifier.)
PUSH
Male
Female
3
3
2
1
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
)
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
( )
R
CHANNEL 1
( )
L
U
1
2
(
(
(
(
(
(
OPTION
C
SBR
SBL
SR
SL
qThis amplifier uses XLR connectors, which are
widely used in professional audio applications, for
the BALANCED connectors. Their features are
described below.
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
SPEAKER CONNECTIONS
B
• Due to their 3-pin construction, the music signals
can be transmitted as balanced signals, and the
effects of extraneous noise are minimal.
Speaker cable
BALANCED:
• Their connect/disconnect locking mechanism
minimizes any shakiness in the connector area
and performs high reliability.
The XLR audio cable is used for connection with the control amplifier.
UNBALANCED:
The RCA audio cable is used for connection with the control amplifier.
wFor professional audio applications, the XLR
connectors can be connected in the following two
ways.
Notes:
• Select the input, whether balanced or unbalanced, before turning on the power. Failure may occur if it is
selected after the power has already been turned on.
1. European system (pin w = hot, pin e = cold)
• If the amplifier input and input selector switch settings are incorrectly matched, no sound will be output from
the amplifier.
HOT
GND
2
1
3
COLD
2. U.S. system (pin w = cold, pin e = hot)
GND
2
1
COLD
3
HOT
eThe XLR connectors on this amplifier use the
European system in 1. above. If a pre-amplifier
or control amplifier with connectors using the U.S.
systemisconnectedtothisamplifierusingbalanced
cables, the signal phase will be reversed.
Tocorrectthesignalphase,reversetheconnections
of pins w and e of the XLR connector at one end
of the cable.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
AV8003 CONNECTIONS
The connection example given below shows the connections between the amplifier and AV8003 AV pre-tuner for basic sound reproduction through 7 channels.
When using the BALANCED inputs, use the XLR audio cables; when using the UNBALANCED inputs, use the RCA audio cables. Connect the PRE OUT connectors on the control amplifier to the input connectors on this
amplifier. Use this connection example as a reference when a control amplifier other than the AV8003 is to be used.
Notes:
• Do not connect the power cables of this amplifier and other components to the AC outlet until all the connections have been completed.
• Insert the plugs on the connecting cables firmly into the connectors. Noise may be caused by improper connections.
• For details on the components connected to this amplifier, refer to the operating instructions of each component.
UNBALANCED CONNECTIONS
BALANCED CONNECTIONS
AV PRE TUNER AV8003
AV PRE TUNER AV8003
(
)
(
INPUT 2 DVD
)
INPUT
1
TV
( )
TV
( )
INPUT 2 DVD
INPUT
1
L
L
R
R
OUT
PUT
1
OUT
PUT
1
SR
SL
SR
SL
( )
FM 75Ω GND AM
( )
FM 75Ω GND AM
OUT
PUT
2
OUT
PUT
2
ANTENNA
ANTENNA
R
L
SR
SL
R
L
SR
SL
C
B
C
R
C
B
C
R
C
B
/
C
R
/
PR
CONNECTION
Y
/
/
Y
/
/
Y
SBR
SW
SBL
C
C
B
C
R
C
B
C
R
C
B
/
CR
/
PR
CONNECTION
COMPONENT
VIDEO
Y
/
/
Y
/
PB
/
P
Y
SBR
SW
SBL
C
P
B
PR
P
B
P
R
P
B
COMPONENT
VIDEO
P
B
P
R
R
PB
1
2
3
GND
HOT(+)
COLD
1
2
3
GND
HOT(+)
COLD(
(
)
(
4
)
INPUT
3
VCR1
INPUT
DSS/VCR2
OUTPUT
(
)
(
)
INPUT
3
VCR1
INPUT
4
DSS/VCR2
OUTPUT
1
2
1
2
( )
TV
(
)
( ) ( )
INPUT 3 VCR1 INPUT 4 DSS/VCR2 OUTPUT
INPUT
1
INPUT
2
DVD
1
2
( )
TV
(
)
( ) ( )
INPUT 3 VCR1 INPUT 4 DSS/VCR2 OUTPUT
3
INPUT
1
INPUT
2
DVD
1
2
(
3
-
)
-
)
VCR1(3)
IN OUT
DSS/VCR2(4)
IN OUT
MONI. OUT
VCR1(3)
IN OUT
DSS/VCR2(4)
IN OUT
MONI. OUT
TV(1) DVD2)
VCR1(3)
DSS/VCR2(4MONITOR ZONE TV(1) DVD2)
OUT OUT
R ZONE TV(1) DVD(2)
OUT
SBR
SBL
SW
C
SBR
SBL
SW
C
NETWORK
UNBALANCED
RS-232C
BALANCED
PRE OUT
SIRIUS SPEAKER
NETWORK
UNBALANCED
RS-232C
BALANCED
PRE OUT
SIRIUS SPEAKER
C
C
CONNECTION
CONN
CD/CDR BALANCED IN
CD/CDR BALANCED IN
S-VIDEO
DC OUT
1
2
3
GND
ON OFF
ON OFF
(+)
2
1
HOT
PUSH
PUSH
PUSH
PUSH
3
COLD
-
( )
LD(
-
)
1
1
2
1
1
2
N
IR
RECEIVER
IN
IR
FLASHER RECEIVER
IN IN
L
FLASHER
IN
AC IN
AC IN
L
UNBALANCED
BALANCED
UNBALANCED
BALANCED
R
OPT.
2
2
EMITTER
OUT
OUT
UT
R
L
L IN
DVD
DIGITAL OUT
MAN ZOE
SELECTOR
L
SELECTOR
TV
VCR1
DSS/VCR2
TAPE
CD/CDR
ZONE OUT
L
SL
SBL
C
/
E
CD/CDR
SBL
C
L
MODEL NO. AV8003
MODEL NO. AV8003
SL
7.1CH
IN
7.1CH
IN
SR
SL
SBL
C
3
3
3
R
1
2
1
2
1
2
IN
OUT
IN
OUT
IN
OUT
IN
OUT
A
B
R
SR
SBR
SW
B
R
SR
SBR
SW
(
)
AUDIO
AUX
(
)
AUX
R
L
SR
SL
CONNECTION
R
L
SR
SL
BL
C
CONNECTION
SBR
SW
1
2
3
GND
1
2
3
GND
HOT
COLD
(+)
HOT
1
2
(+)
(
1
2
3
(
-
)
COLD
3
-
)
Subwoofer inside
the amplifier
3
3
3
1
2
1
2
1
2
SBR
SBL
BALANCED
SW
C
SBR
SBL
BALANCED
SW
C
NETWORK
ED
NETWORK
UNBALANCED
RS-232C
PRE OUT
PRE OUT
SPEAKER C
Subwoofer inside
the amplifier
RCA audio cables
XLR audio cables
Set the switch to
BALANCED.
Set the switch to
UNBALANCED.
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
(
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
)
CHANNEL 1 UNBALANCED
( )
L
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
(
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
)
CHANNEL 1 UNBALANCED
( )
L
(
(
C
(
)
(
(
SL
(
R
UNBALANCED
BALANCED
OPTION
SBR
SBL
SR
(
(
C
(
)
(
(
(
UNBALANCED
BALANCED
OPTION
SBR
SBL
SR
SL
R
OUT IN
OUT
IN
OUT IN
OUT
IN
UNBALANCED
BALANCED
UNBALLANCED
BALANCED
UNBALLANCED
BALANCED
UNBALLANCED
BALANCED
UNBALLANCED
BALANCED
UNBALLANCED
BALANCED
UNBALLANCED
BALANCED
UNBALANCED
BALANCED
FLASHER
IN
DC CONTROL REMOTE CONTROL
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALAANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
FLASHER
IN
DC CONTROL REMOTE CONTROL
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
BALANCED
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
BALANCED
2
1
2
1
3
2
(
3
2
(
1
3
GND HOT
COLD
CONNECTION
(+)
1
3
GND HOT
COLD
CONNECTION
(+)
-
)
-
)
UNSWITCHED 1.25A 150W
UNSWITCHEDD 1.255AA 150W
AC IN
AC IN
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
)
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
)
CHANNEL 1 SPEAKER SYSTEMS
6-8 OHMS
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
(
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
)
CHANNEL 1 SPEAKER SYSTEMS
6-8 OHMS
(
(
(
(
(
(
(
( )
L
OPTION
C
SBR
SBL
SR
SL
R
(
(
(
)
(
(
(
( )
L
OPTION
C
SBR
SBL
SR
SL
R
MODEL NO. MM8003
MODEL NO. MM8003
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
SPEAKER CONNECTIONS
Notes:
• To protect the circuitry from damage, do not connect
SPEAKER CONNECTIONS
SPEAKER CABLES
Refer to the figure below, and connect the speakers to the amplifier.
Remove about 10 mm of the covering from the
1.
2.
3.
4.
5.
two bare speaker cables together or allow them to
touch any metal parts of the amplifier.
end of the speaker cable.
Twist the bare part of the cable tightly to prevent
short-circuiting.
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
(
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
)
CHANNEL 1 UNBALANCED
(
(
(
(
)
(
(
(
)
L
OPTION
C
SBR
SBL
SR
SL
R
Turn the speaker connector counterclockwise
to loosen it.
OUT IN
OUT
IN
AC OUTLE
120V 60H
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
FLASHER
IN
DC CONTROL REMOTE CONTROL
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
BALANCED
Insert the bare part of the speaker cable into
the hole at the side of the speaker connector.
2
1
3
1
3
GND HOT
2
(+)
(
-
)
COLD
CONNECTION
UNSWITCHEDD 1.25A
Turn the speaker connector clockwise to
tighten it up.
AC IN
CHANNEL 8
(
CHANNEL 7
(
CHANNEL 6
(
CHANNEL 5
(
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
)
CHANNEL 1 SPEAKER SYSTEMS
6-8 OHMS
• Due to the risk of electric shock, do not touch the
speaker connectors while the power is supplied.
)
)
)
)
(
(
(
( )
L
OPTION
C
SBR
SBL
SR
SL
R
1.
2.
MODEL NO. MM8003
3.
4.
5.
Center speaker Surround Surround Surround Surround
Front
right
speaker speaker
(R) (L)
Front
left
(C)
back
right
back left
speaker
(SBL)
right
speaker speaker
(SR) (SL)
left
speaker
(SBR)
Notes:
• Speakers come with "+" and "-" terminals. When connecting the speakers to the amplifier, connect their "+"
terminals to the "+" connectors on the amplifier and, similarly, connect their "-" terminals to the "-" connectors.
If a "+" terminal is connected to a "-" connector, the signal phase will be reversed, and the music played through
the speakers will sound unnatural. Refer to the operating instructions of the speakers, and properly reconnect the
speakers.
• Connect speaker systems with an impedance of at least 6 Ω to the amplifier. If speakers with an impedance of under
6 Ω are used and sound is played at high volume levels for prolonged periods, the amplifier may experience an
extreme rise in temperature, tripping the protection circuit.
• If the AV8003 AV pre-tuner is connected to the amplifier and one surround back speaker is to be used, connect the
speaker to the surround back left channel (SBL).
If this is the case, the setting must be performed on theAV8003. (For details, refer to the operating instructions of the
AV8003.) When using a control amplifier other than the AV8003, follow the operating instructions of the amplifier
used, and connect the speaker properly.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
TIPS ON SPEAKER PLACEMENT
POWER CABLE CONNECTION
USING AC OUTLETS
How the speakers should be placed depends on the room size and other factors. An example of how the
speakers are normally placed and some placement tips are given here.
Connect the power cable after all the connections
have been completed.
Power can be supplied from the amplifier's AC outlet
(UNSWITCHED) to another component up to a
maximum power consumption of 150 W.
The amplifier's AC outlet is an UNSWITCHED
(unswitched) type, which means that the power can
be supplied at all times regardless of whether the
amplifier power is on or off.
Surround R
Plug the accessory power cable into the AC IN
1.
Surround
Back R
socket on the rear panel of the amplifier.
Front R
Front
Center
AC OUTLET
120V 60Hz
UNSWITCHED 1.25A150W
Surround L
Surround
Back L
Front L
Warning:
Do NOT connect a component that exceeds the
absolute allowable power rating. Doing so may cause
a fire and/or electric shock.
• Front left and right speakers
• Surround left and right speakers
It is recommended that the front left and right
speakers be positioned at an angle of 45 to 60
degrees from each other as viewed from the listening
position.
These speakers are needed to play surround sound.
Place them against the walls in line with the listening
position or slightly behind it. Position them so that
the center of the speaker front panels point toward
the center the room.
Connect the plug on the power cable to the wall
socket (AC 120 V, 60 Hz).
2.
* Ensurethatthetotalpowerconsumptionofthe
amplifier and other components connected to
the socket does not exceed the capacity of
the socket.
• Center speaker
This speaker is placed so that its front panel is in
line with the front panels of the front left and right
speakers or slightly behind them.
• Surround back left and right speakers
Place these speakers behind the listening position as
shown in the figure.
Notes:
• Insert the power plug firmly. Noise may be caused
by an incomplete connection.
Height at which to place the front left and right
speakers and center speaker
Place the three front speakers (left, right and center)
so that their mid-range and high-range units will be
positioned at more or less the same height from the
floor as much as possible.
Height at which to place the surround left and
right speakers and surround back left and right
speakers
Place these speakers at a height of 70 cm to 1 meter
above the listener.
By placing the speakers at this height, the sound
source will not be localized at any specific position,
and the listener will feel more surrounded and
enveloped by the sound.
• Do not connect the amplifier to the AC outlet of
another product. Product malfunctioning may occur
if the capacity of the AC outlet is exceeded.
70cm 1m
Note:
When placing speakers close to a TV set, use
magnetically shielded speakers for the front left and
right speakers and center speaker.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
OPERATION
POWER ON/STANDBY
switch
TURNING THE POWER ON
Standby indicator
Press the POWER ON/STANDBY switch.
1.
2.
Sound is output after the standby indicator goes off and the illumination lamp has blinked for about 7
seconds.
8CH POWER AMPLIFIER MM8003
The sound output is delayed because of the activation of the muting circuit, which prevents noise from being output
until the amplifier's circuitry operates stably after the power has been turned on.
(The illumination lamp is lit while the amplifier is operating.)
Note:
Before turning the power on, turn down the volume controls on the connected components.
STANDBY
POWER ON/STANDBY
TURNING THE POWER OFF
Press the POWER ON/STANDBY switch.
1.
2.
The illumination lamp goes off, the standby indicator lights, and the amplifier goes into standby mode.
Note:
Illumination lamp
Power is still supplied to some circuits even while the amplifier is in standby mode.
Disconnect the power cable plug from the power outlet when you leave home for a prolonged period.
Make sure you can disconnect the plug from the power outlet at any time in order to prevent possible accidents.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
ADVANCED CONNECTIONS
BI-AMPLIFIER CONNECTIONS
Four channels of this unit's power amplifiers are used to achieve bi-amplifier connections to the front speaker
systems.
Before connecting the speaker systems, check that they support bi-amplifier connections.
Notes:
• Balanced cables are used in the connection example shown. (Unbalanced cables can also be used for bi-amplifier
connections.)
• If the front speaker systems are used in combination with the AV8003 in a bi-amplifier connection, sound will no
longer be heard from the surround back channels.
What are "bi-amplifier connections"?
This is a technique for enhancing sound quality, and it involves connecting separate power amplifiers to the
bass and mid-range/treble speakers.
By adopting this technique, interference in the mid-range and treble sound caused by the back electromotive
force generated by the bass speaker unit can be minimized, improving the sound that can be delivered through
the front speakers.
L
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
(
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
)
CHANNEL 1 UNBALANCED
)
SL
(
(
(
)
(
(
(
(
L
OPTION
C
SBR
SBL
SR
SL
R
OUT IN
OUT
IN
AC OUTLET
120V 60Hz
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
FLASHER
IN
DC CONTROL REMOTE CONTROL
R
L
SR
SL
CONN
SBL
C
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
1
2
3
GN
HO
CO
BALANCED
2
1
3
1
3
GND HOT
2
(+)
(
-
)
COLD
CONNECTION
UNSWITCHED 1.25A 150W
AC IN
SBR
SBL
BALANCED
SW
C
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
)
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
)
CHANNEL 1 SPEAKER SYSTEMS
6-8 OHMS
N
ANCED
(
(
(
(
(
(
(
( )
L
OPTION
C
SBR
SBL
SR
SL
R
PRE OUT
SPEAKER C
RS-232C
MODEL NO. MM8003
ON OFF
AV8003
(
INPUT 1 TV
)
(
)
INPUT
2
DVD
L
R
OUT
PUT
1
SR
SL
( )
FM 75Ω GND AM
OUT
PUT
2
ANTENNA
R
L
SR
SL
C
B
C
R
C
B
C
R
CB
CR
CONNECTION
Y
/
/
Y
INPUT 4 DSS/VCR2
DSS/VCR2 OUTPUT 1 OUTPUT 2
/
/
Y
/
P
/
PR
SBR
SW
SBL
C
COMPONENT
VIDEO
P
B
P
R
P
B
P
R
B
1
2
3
GND
(
)
(
)
INPUT 3 VCR1
(+)
HOT
1
2
(
INPUT 1 TV
)
(
INPUT 2 DVD
)
(
3
)
VCR1 INPUT
(
4
)
INPUT
3
( )
-
COLD
VCR1(3)
IN OUT
DSS/VCR2(4)
IN OUT
MONI. OUT
TV(1) DVD(2)
VCR1(3)
DSS/VCR2(4) MONITOR ZONE TV(1) DVD(2)
OUT OUT
SBR
SBL
BALANCED
SW
C
NETWORK
UNBALANCED
RS-232C
PRE OUT
SIRIUS
SPEAKER C
CONNECTION
CD/CDR BALANCED IN
S-VIDEO
DC OUT
VIDEO
IN
OUT
IN
OUT
REMOTE
1
2
3
GND
ON OFF
(+)
HOT
2
1
PUSH
PUSH
3
( )
-
COLD
4
1
5
2
6
COAX.
1
1
2
IN
IR
FLASHER RECEIVER
IN IN
AC IN
UNBALANCED
BALANCED
3
OPT.
2
EMITTER
OUT
OUT
R
L
DIGITAL IN
DVD
DIGITAL OUT
MAIN ZONE
SELECTOR
TV
VCR1
DSS/VCR2
TAPE
CD/CDR
ZONE OUT
L
SL
SBL
C
L
MODEL NO. AV8003
7.1CH
IN
R
IN
OUT
IN
OUT
IN
OUT
IN
OUT
A
B
R
SR
SBR
SW
(
)
AUX
AUDIO
Set the SPEAKER C switch to
ON.
ON OFF
For further details, refer to the
operating instructions of the
AV8003.
Center speaker
(C)
Surround
right
speaker
(SR)
Surround
left speaker
(SL)
Front right speaker
Front left speaker
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
MULTI ZONE SPEAKER CONNECTIONS
The example given here shows the connections performed when two pairs of this unit's power amplifiers are used for multi zone speakers in combination with the AV8003.
For details on the multi zone speaker function, refer to the operating instructions of the AV8003.
L
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
(
CHANNEL 4
(
CHANNEL 3
(
CHANNEL 2
)
CHANNEL 1 UNBALANCED
)
SL
SBL
C
(
(
C
(
)
)
)
SL
(
R
(
L
OPTION
SBR
SBL
SR
OUT IN
OUT
IN
AC OUTLET
120V 60Hz
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
FLASHER
IN
DC CONTROL REMOTE CONTROL
R
L
SR
SL
CONN
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
1
2
3
GN
HO
CO
BALANCED
2
1
3
1
3
GND HOT
2
(+)
( )
-
COLD
CONNECTION
UNSWITCHED 1.25A 150W
SBR
SBL
BALANCED
SW
C
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
)
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
)
CHANNEL 1 SPEAKER SYSTEMS
6-8 OHMS
N
ANCED
(
(
(
(
(
(
(
( )
L
OPTION
C
SBR
SBL
SR
SL
R
PRE OUT
SPEAKER C
RS-232C
MEL NO. MM8003
ON OFF
(
INPUT 1 TV
)
(
2
)
DVD
INPUT
L
R
OUT
PUT
1
SR
SL
( )
FM 75Ω GND AM
OUT
PUT
2
ANTENNA
R
L
SR
SL
C
B
C
R
C
B
C
R
C
B
/
CR
/
PR
CONNECTION
GND
Y
/
/
Y
INPUT 4 DSS/VCR2
DSS/VCR2 OUTPUT 1 OUTPUT 2
/
/
Y
SBR
SW
SBL
C
COMPONENT
VIDEO
P
B
P
R
P
B
P
R
PB
1
(
)
(
)
INPUT 3 VCR1
2
3
(+)
HOT
1
2
(
INPUT 1 TV
)
(
INPUT 2 DVD
)
(
3
)
VCR1 INPUT
(
4
)
INPUT
3
( )
-
COLD
VCR1(3)
IN OUT
DSS/VCR2(4)
IN OUT
MONI. OUT
TV(1) DVD)
VCR1(3)
DSS/VCR2(4MONITOR ZONE TV(1) DVD2)
OUT OUT
SBR
SBL
BALANCED
SW
C
NETWORK
UNBALANCED
RS-232C
PRE OUT
SIRIUS
SPEAKER C
CONNECTION
CD/CDR BALANCED IN
S-VIDEO
DC OUT
VIDEO
IN
OUT
IN
OUT
REMOTE
1
2
3
GND
ON OFF
(+)
HOT
2
1
PUSH
PUSH
3
(
-
)
COLD
4
1
5
2
6
COAX.
1
1
2
IN
IR
FLASHER RECEIVER
IN IN
AC IN
UNBALANCED
BALANCED
3
OPT.
2
EMITTER
OUT
OU
R
L
DIGITAL IN
DVD
DIGITAL OUT
MAIN ZONE
SELECTOR
Monitor
TV
VCR1
DSS/VCR2
TAP
CD/CDR
ZONE OUT
L
SL
SBL
C
L
MODEL NO. AV8003
7.1CH
IN
R
IN
OUT
IN
OUT
IN
IN
OUT
A
B
R
SR
SBR
SW
(
)
AUX
AU
(
ONITOR ZONE TV 1
OUT
)
OUT
Center speaker
(C)
Surround
right
speaker
(SR)
Surround
left speaker
(SL)
Front
right
speaker
(R)
Front left
speaker
(L)
Speaker (L)
Speaker (R)
ON OFF
ULTI RC
DC OU
VIDEO IN
Main zone
Zone A
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
MULTI ZONE CONNECTIONS
The example given here shows the connections performed where six pairs of this unit's power amplifiers are connected in combination with the AV8003 for multi zone use.
These connections allow the sound to be played in stereo in up to four rooms, including the main room.
For details on the multi zone function, refer to the operating instructions of the AV8003.
L
R
R
L
R
L
R
L
R
L
R
L
AV8003
(
INPUT 1 TV
)
(
INPUT 2 DVD
)
L
R
OUT
PUT
1
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
(
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
)
CHANNEL 1 UNBALANCED
)
(
(
(
)
(
(
(
(
L
OPTION
C
SBR
SBL
SR
SL
R
SR
SL
( )
FM 75Ω GND AM
OUT
PUT
2
ANTENNA
OUT IN
OUT
IN
AC OUTLET
120V 60Hz
R
L
SR
SL
UNBALAANCED
BALANCED
UNBALAANCED
BALANCED
UNBALAANCED
BALANCED
UNBALAANCED
BALANCED
UNBALAANCED
BALANCED
UNBALAANCED
BALANCED
UNBALAANCED
BALANCED
UNBALAANCED
BALANCED
FLASHER
IN
CONNECTION
DC CONTROL REMOTE CONTROL
C
B
/
C
R
C
B
/
CR
CB
CR
/
Y
/
Y
/
P
Y
/
PB
SBR
SW
SBL
C
COMPONENT
VIDEO
PB
P
R
P
B
R
PR
1
2
3
GND
(
INPUT 3 VCR1
)
(
INPUT 4 DSS/VCR2
)
(+)
HOT
1
2
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
(
INPUT 1 TV
)
(
INPUT 2 DVD
)
( ) ( )
INPUT 3 VCR1 INPUT 4 DSS/VCR2 OUTPUT 1 OUTPUT 2
3
( )
-
COLD
BALANCED
2
1
3
VCR1(3)
IN OUT
DSS/VCR2(4)
IN OUT
MONI. OUT
1
3
GND HOT
2
(+)
TV(1) DVD(2)
VCR1(3)
DSS/VCR2(4) MONITOR ZONE TV(1) DVD(2)
OUT OUT
SBR
SBL
BALANCED
SW
C
(
-
)
COLD
NETWORK
UNBALAANCED
RS-232C
CONNECTION
PRE OUT
UNSWITCHED 1.25A 150W
SIRIUS
SPEAKER C
AC IN
CONNECTION
CD/CDR BALLANCED IN
S-VIDEO
DC OUT
VIDEO
IN
OUT
IN
OUT
REMOTE
1
2
3
GND
ON OFF
(+)
HOT
2
1
PUSH
PUSH
3
(
-
)
COLD
4
1
5
2
6
COAX.
1
1
2
IN
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
(
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
(
CHANNEL 1 SPEAKER SYSTEMS
6-8 OHMS
IR
FLASHER RECEIVER
IN IN
(
(
(
)
(
(
)
( )
L
OPTION
C
SBR
SBL
SR
SL
R
AC IN
UNBALANCED
BALANCED
3
OPT.
2
EMITTER
OUT
OUT
R
L
DIGITTAL IN
DVD
DIGITAL OUT
MAIN ZONE
SELECTOR
TV
VCR1
DSS/VCR2
TAPE
CD/CDR
ZONE OUT
L
SL
SBL
C
MODEL NO. MM8003
L
ODEL NO. AAV8003
7.1CH
IN
R
IN
OUT
IN
OUT
IN
OUT
IN
OUT
A
B
R
SR
SBR
SW
(
)
AUX
AUDIO
L
R
R
L
ON OFF
R
L
R
L
R
L
R
L
Zone C
Zone B
Zone A
Main zone
(MULTI ZONE SPEAKER)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
REMOTE CONTROL CONNECTIONS
CONNECTIONS WITH EXTERNAL CONTROL COMPONENTS
By connecting the remote control connectors on the AV8003 and this amplifier, the amplifier can be set to
STANDBY ON/OFF synchronized with the STANDBY ON/OFF operations of the AV8003.
For the connection, use the accessory RCA cable to connect the REMOTE CONTROL OUT connector on the
AV8003 and the REMOTE CONTROL IN connector on this amplifier.
q
w
e
r
For details on operation, refer to the operating instructions of the AV8003.
AV PRE TUNER AV8003
NBALAANCED
(
INPUT 1 TV
)
(
INPUT 2 DVD
)
L
R
OUT
PUT
1
SR
SL
( )
FM 75Ω GND AM
OUT
PUT
2
ANTENNA
R
L
SR
SL
C
B
C
R
C
B
C
R
CB
/
CR
/
PR
CONNECTION
Y
/
/
Y
/
/
Y
SBR
SW
SBL
C
COMPONENT
VIDEO
PB
PR
PB
P
R
PB
OUT IN
OUT
IN
1
2
3
GND
(
INPUTT 3 VCR1
)
(
INPUT 4 DSS/VCR2
)
(+)
HOT
1
2
(
INPUT 1 TV
)
(
INPUT 2 DVD
)
( ) ( )
INPUT 3 VCR1 INPUT 4 DSS/VCR2 OUTPUT 1 OUTPUT 2
3
( )
-
COLD
FLASHER
IN
DC CONTROL REMOTE CONTROL
(
)
(
)
VCR1
IN
3
OUT
DSS/VCR2 4
IN OUT
MONI. OUT
( )
TV 1
(
)
2
(
)
3
(
)
4
( )
1
( )
DVD 2
DVD
VCR1
DSS/VCR2
MONITOR ZONE TV
OUT OUT
SBR
SBL
BALANCED
SW
C
NETWORK
UNBALANCED
RS-232C
PRE OUT
SIRIUS
SPEAKER C
CONNECTION
ALANCED
CD/CDR BALANCED IN
S-VIDEO
DC OUT
VIDEO
IN
OUT
IN
OUT
REMOTE
1
2
3
GND
ON OFF
(+)
HOT
2
1
PUSH
PUSH
3
( )
-
COLD
4
1
5
2
6
COAX.
1
1
2
IN
IR
FLASHER RECEIVER
IN IN
AC IN
UNBALAANCED
BALANCED
3
OPT.
2
q
Flasher input connector
This is used to control the amplifier from the rooms
using a key pad or other device.
e
DC CONTROL IN connector
EMITTER
OUT
OUT
R
L
DIGITAL IN
DVD
DIGITAL OUT
MAIN ZONE
SELECTOR
This is connected to an external component equipped
with a DC CONTROL OUT connector.
The amplifier's power on or standby mode can be
selected in tandem with the power on/off operation
of the component that has been connected to this
connector.
TV
VCR1
DSS/VCR2
TAPE
CD/CDR
ZONE OUT
L
SL
SBL
C
L
MODEL NO. AV8003
7.1CH
IN
R
GND
IN
OUT
IN
OUT
IN
OUT
IN
OUT
A
B
R
SR
SBR
SW
(
)
AUX
AUDIO
Signal
For details, refer to the operating instructions of the
connected component.
GND
w
DC CONTROL OUT connector
This is used to control external components in
tandem with the power on/off operation of this
amplifier.
Signal
When the amplifier power is OFF, a voltage of 0 V
is output from the DC CONTROL OUT connector;
when it is ON, a DC 12 V voltage is output.
Note:
The amplifier's power is turned on when a voltage in
the range of DC 5-15 V is input to the DC CONTROL
IN connector. (Standby mode is established with a 0
V input.)
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
(
CHANNEL 4
)
CHANNEL 3
)
CHANNEL 2
)
CHANNEL 1 UNBALANCED
)
(
(
C
(
)
(
(
(
(
L
OPTION
SBR
SBL
SR
SL
R
GND
OUT IN
OUT
IN
AC OUTLET
120V 60Hz
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
UNBALANCED
BALANCED
FLASHER
IN
DC CONTROL REMOTE CONTROL
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
BALANCED
Bear in mind that malfunctioning may result when a
voltage higher than 15 V is input.
Signal
2
1
3
2
(
1
3
GND HOT
COLD
CONNECTION
(+)
-
)
UNSWITCHED 1.25A 150W
Notes:
AC IN
• The maximum output current of the DC CONTROL
OUT connector is 44 mA. Check the operating
instructions of the components to be connected
before performing the connections.
r
Remote control connector
CHANNEL 8
)
CHANNEL 7
)
CHANNEL 6
)
CHANNEL 5
(
CHANNEL 4
)
CHANNEL 3
(
CHANNEL 2
)
CHANNEL 1 SPEAKER SYSTEMS
6-8 OHMS
(
(
(
)
(
)
(
( )
L
OPTION
C
SBR
SBL
SR
SL
R
This is used when configuring a system with another
Marantz product and using it to control this amplifier.
Connect the REMOTE CONTROL OUT connector
of the other Marantz product to the REMOTE
CONTROL IN connector of the amplifier and the
REMOTE CONTROL IN connector of the Marantz
product to the REMOTE CONTROL OUT connector
of the amplifier.
MODEL NO. MM8003
• Do not use the DC CONTROL OUT connector as
the power supply for external components.
Note:
By connecting the amplifier to the AV8003, the
amplifier's power can be set to on or standby in tandem
with the power on/standby operations of the AV8003.
For details, refer to the operating instructions of the
AV8003.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
RESETTING THE AMPLIFIER
TROUBLESHOOTING
This amplifier features a microcontroller.
The microcontroller can be reset by following the steps below.
If you believe something is wrong with your amplifier, check the following points. Unintentional errors in
operation or mistakes made in the connections are sometimes misinterpreted as failure.
If the failure persists even after checking the below points, contact your dealer, your nearest Marantz Consumer
Marketing office or customer center, or a Marantz service center.
Related
page
Symptom
Cause
Remedy
IN
OUT
IN
The amplifier's power fails to The power plug is not connected.
come on.
Insert the power plug into the wall
outlet.
7
ONTROL REMOTE CONTROL
No sound can be heard from the The connecting cables (input) or speaker Check the cable connections.
speakers.
5, 6
4
cables have been incorrectly connected.
The setting of one or more of the input Set the input switch to the position that
selector switches does not correspond corresponds to the input connected to
to the input connector (BALANCED or the amplifier.
UNBALANCED) to which the cable has
Set the amplifier to standby or turn its power on.
1.
2.
been connected.
Use the tip of a needle or other sharp-pointed object to press the reset switch in the hole indicated by the
arrow for at least 1 second.
The power suddenly goes The temperature inside the amplifier has
off, and the standby indicator risen, tripping the protection circuit.
blinks slowly (about two times
•
•
Turn off the power, and wait until
the amplifier's temperature has
fallen to a low enough level before
turning the power back on.
When the amplifier power is already on, the amplifier is first set to standby mode, after which the
microcontroller is initialized, and the power is turned back on.
3.
a second).
2
6
Check whether the amplifier has
been installed in a position that
interferes with the dissipation of its
heat.
When the microcontroller is reset with the amplifier in standby mode, it is initialized, then the power is
turned back on.
The protection circuit has been tripped
because two conductors ("+" and "-") of
a speaker cable are touching each other
or because the conductors have made
contact with the rear panel or another
metal part.
•
•
Turn the power off, and check the
speaker cable connections.
Re-process the ends of the
conductors of the speaker cables.
Sound is being played at a volume higher Turn the power off, turn down the
than the performance of the amplifier can volume control on the control amplifier
deliver. connected to this amplifier, then turn
the power back on.
–
6
Speakers with an impedance below the Use speakers with the specified
specified rating (6 Ω) are being used. impedance.
The power suddenly goes off, The amplifier's protection circuit has Disconnect the power plug from the
and the standby indicator blinks been tripped.
rapidly (about eight times a
second).
power outlet, and ask your nearest
service center to repair the amplifier.
14
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
OTHERS
SPECIFICATIONS
The section describes the care and maintenance
tasks that must be performed to optimize the
operation of your Marantz equipment.
Rated power output (from 20 Hz to 20 kHz/THD = 0.08 % two
channels driven)
OUTSIDE DIMENSIONS
CLEANING OF EQUIPMENT EXTERNAL SURFACES
.........................................................140 W / ch 8 Ω
.........................................................170 W / ch 6 Ω
Output bandwidth (8-Ω load, 0.09%)
...........................................................5 Hz – 40 kHz
Frequency response (1 W, 8 Ω)
...........................................8 Hz – 100 kHz ( 3 dB)
Damping factor .................................................................. 100
Input sensitivity/impedance
................................1.2 V/ 22 k Ω (UNBALANCED)
...................................... 2.4 V/30 k Ω (BALANCED)
Signal-to-noise ratio (IHF-A).........................................105 dB
Voltage amplification level ..............................................29 dB
Supply voltage..................................................AC120V 60 Hz
Power consumption.......................................................800 W
Standby power................................................................0.4 W
Weight ......................................................................17.9 kg
Accessories
The exterior finish of your unit will last indefinitely with
proper care and cleaning, Never use scouring pads,
steel wool, scourging powders or harsh chemical
agents (e.g., lye solution), alcohol, thinner, benzine,
insecticide or other volatile substances as these wil
mar the finish of the equipment. Likewise, never
use cloths containing chemical substances. If the
equipment get dirty, wipe the external surfaces with
a soft, lint-free cloth.
If the equipment becomes heavily soiled:
• dilute some washing up liquid in water, in a ratio of
one part detergent to six parts water.
• dip a soft, lint free in the solution and wring the it is
damp.
Power cable................................................................... 1
Remote control cable..................................................... 1
Warranty card
• wipe the equipment with the damp cloth.
• dry the equipment by wiping it with a dry cloth.
USA........................................................................ 1
Canada .................................................................. 1
Operating instructions (this document).......................... 1
17-3/8 ins. (440 mm)
REPAIRS
Only the most competent and qualified service
technicians should be allowed to service the
factory-trained warranty station personnel have
the knowledge and special facilities needed for
repair and calibration of this precision equipment.
After the warranty period has expired, repairs will
be performed for a charge if the equipment can be
returned to normal operation.
In the event of difficulty, refer to your dealer or write
directly to the nearest location to you that is listed on
the Marantz Authorized Service Station list. If writing,
please include the model and serial number of the
equipment together with a full description of what you
think is abnormal about the equipment’s behaviour.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
You can find your nearest authorized distributor or dealer on our website.
is a registered trademark.
Printed in China
04/2008
541110074027M mzh-d
Download from Www.Somanuals.com. All Manuals Search And Download.
|