Makita Power Hammer HPR2410 User Manual

Rotary Hammer  
24 mm (15/16”)  
MODEL HR2410  
003094  
DOUBLE  
INSULATION  
I N S T R U C T I O N M A N U A L  
WARNING:  
For your personal safety, READ and UNDERSTAND before using.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11. Avoid accidental starting. Be sure switch  
is off before plugging in. Carrying tools with  
your finger on the switch or plugging in tools  
that have the switch on invites accidents.  
Electrical Safety  
4. Double insulated tools are equipped with  
a polarized plug (one blade is wider than  
the other.) This plug will fit in a polarized  
outlet only one way. If the plug does not fit  
fully in the outlet, reverse the plug. If it  
still does not fit, contact a qualified elec-  
trician to install a polarized outlet. Do not  
change the plug in any way. Double insula-  
12. Remove adjusting keys or wrenches  
before turning the tool on. A wrench or a  
key that is left attached to a rotating part of  
the tool may result in personal injury.  
13. Do not overreach. Keep proper footing  
and balance at all times. Proper footing and  
balance enables better control of the tool in  
unexpected situations.  
tion  
eliminates the need for the three wire  
grounded power cord and grounded power  
supply system.  
5. Avoid body contact with grounded sur-  
faces such as pipes, radiators, ranges and  
refrigerators. There is an increased risk of  
electric shock if your body is grounded.  
14. Use safety equipment. Always wear eye  
protection. Dust mask, non-skid safety  
shoes, hard hat, or hearing protection must  
be used for appropriate conditions. Ordinary  
eye or sun glasses are NOT eye protection.  
6. Do not expose power tools to rain or wet  
conditions. Water entering a power tool will  
increase the risk of electric shock.  
Tool Use and Care  
15. Use clamps or other practical way to  
secure and support the workpiece to a  
stable platform. Holding the work by hand or  
against your body is unstable and may lead  
to loss of control.  
7. Do not abuse the cord. Never use the cord  
to carry the tools or pull the plug from an  
outlet. Keep cord away from heat, oil,  
sharp edges or moving parts. Replace  
damaged cords immediately. Damaged  
cords increase the risk of electric shock.  
16. Do not force tool. Use the correct tool for  
your application. The correct tool will do the  
job better and safer at the rate for which it is  
designed.  
8. When operating a power tool outside, use  
an outdoor extension cord marked “W-A”  
or “W”. These cords are rated for outdoor  
use and reduce the risk of electric shock.  
17. Do not use tool if switch does not turn it  
on or off. Any tool that cannot be controlled  
with the switch is dangerous and must be  
repaired.  
Personal Safety  
9. Stay alert, watch what you are doing and  
use common sense when operating a  
power tool. Do not use tool while tired or  
under the influence of drugs, alcohol, or  
medication. A moment of inattention while  
operating power tools may result in serious  
personal injury.  
18. Disconnect the plug from the power  
source before making any adjustments,  
changing accessories, or storing the tool.  
Such preventive safety measures reduce the  
risk of starting the tool accidentally.  
19. Store idle tools out of reach of children  
and other untrained persons. Tools are  
dangerous in the hands of untrained users.  
10. Dress properly. Do not wear loose cloth-  
ing or jewelry. Contain long hair. Keep  
your hair, clothing, and gloves away from  
moving parts. Loose clothes, jewelry, or long  
hair can be caught in moving parts.  
20. Maintain tools with care. Keep cutting  
tools sharp and clean. Properly maintained  
tools with sharp cutting edges are less likely  
to bind and are easier to control.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
21. Check for misalignment or binding of  
moving parts, breakage of parts, and any  
other condition that may affect the tools  
operation. If damaged, have the tool ser-  
viced before using. Many accidents are  
caused by poorly maintained tools.  
SERVICE  
23. Tool service must be performed only by  
qualified repair personnel. Service or main-  
tenance performed by unqualified personnel  
could result in a risk of injury.  
24. When servicing a tool, use only identical  
replacement parts. Follow instructions in  
the Maintenance section of this manual.  
Use of unauthorized parts or failure to follow  
Maintenance instructions may create a risk of  
electric shock or injury.  
22. Use only accessories that are recom-  
mended by the manufacturer for your  
model. Accessories that may be suitable for  
one tool, may become hazardous when used  
on another tool.  
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition.  
When using an extension cord, be sure to use one heavy enough to carry the current your  
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of  
power and overheating. Table 1 shows the correct size to use depending on cord length and  
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num-  
ber, the heavier the cord.  
Table 1: Minimum gage for cord  
Volts  
120 V  
Total length of cord in feet  
Ampere Rating  
25 ft.  
50 ft.  
100 ft.  
150 ft.  
More Than  
Not More Than  
AWG  
0
6
10  
12  
6
18  
18  
16  
14  
16  
16  
16  
12  
16  
14  
14  
14  
12  
12  
10  
12  
16  
Not Recommended  
SPECIFIC SAFETY RULES  
USB010-2  
DO NOT let comfort or familiarity with product (gained from  
repeated use) replace strict adherence to rotary hammer safety  
rules. If you use this tool unsafely or incorrectly, you can suffer  
serious personal injury.  
1. Hold tools by insulated gripping surfaces  
when performing an operation where the  
cutting tool may contact hidden wiring or  
its own cord. Contact with a livewire will  
make exposed metal parts of the tool live”  
and shock the operator.  
2. Wear ear protectors when using the tool  
for extended periods. Prolonged exposure  
to high intensity noise can cause hearing  
loss.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Wear a hard hat (safety helmet), safety  
glasses and/or face shield. Ordinary eye  
or sun glasses are NOT safety glasses. It  
is also highly recommended that you wear  
a dust mask and thickly padded gloves.  
7. Always be sure you have a firm footing.  
Be sure no one is below when using the  
tool in high locations.  
8. Hold the tool firmly with both hands.  
9. Keep hands away from moving parts.  
4. Be sure the bit is secured in place before  
operation.  
10. Do not leave the tool running. Operate the  
tool only when hand-held.  
5. Under normal operation, the tool is  
designed to produce vibration. The  
screws can come loose easily, causing a  
breakdown or accident. Check tightness  
of screws carefully before operation.  
11. Do not point the tool at any one in the area  
when operating. The bit could fly out and  
injure someone seriously.  
12. Do not touch the bit or parts close to the  
bit immediately after operation; they may  
be extremely hot and could burn your  
skin.  
6. In cold weather or when the tool has not  
been used for a long time, let the tool  
warm up for a while by operating it under  
no load. This will loosen up the lubrica-  
tion. Without proper warm-up, hammering  
operation is difficult.  
13. Some material contains chemicals which  
may be toxic. Take caution to prevent  
dust inhalation and skin contact. Follow  
material supplier safety data.  
SAVE THESE INSTRUCTIONS  
WARNING:  
MISUSE or failure to follow the safety rules stated in this  
instruction manual may cause serious personal injury.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
FUNCTIONAL  
DESCRIPTION  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before adjusting or checking function on the  
tool.  
003107  
Switch action  
CAUTION:  
1
Before plugging in the tool, always check to see that the  
switch trigger actuates properly and returns to the OFF”  
position when released.  
To start the tool, simply pull the switch trigger. Tool speed is  
increased by increasing pressure on the switch trigger.  
Release the switch trigger to stop.  
1. Switch trigger  
003115  
Reversing switch action  
2
This tool has a reversing switch to change the direction of  
A
rotation. Move the reversing switch lever to the  
position  
(A side) for clockwise rotation or the  
counterclockwise rotation.  
position (B side) for  
B
1
CAUTION:  
Always check the direction of rotation before operation.  
1. Reversing switch lever  
2. Switch trigger  
Use the reversing switch only after the tool comes to a  
complete stop. Changing the direction of rotation before  
the tool stops may damage the tool.  
003124  
Selecting the action mode  
This tool employs an action mode changing knob. Select one  
of the two modes suitable for your work needs by using this  
knob.  
For rotation only, turn the knob so that the arrow on the knob  
points toward the  
For rotation with hammering, turn the knob so that the arrow  
mark on the tool body.  
1
1. Action mode changing knob  
on the knob points toward the  
mark on the tool body.  
CAUTION:  
Always set the knob fully to your desired mode mark. If  
you operate the tool with the knob positioned halfway  
between the mode marks, the tool may be damaged.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Torque limiter  
The torque limiter will actuate when a certain torque level is  
reached. The motor will disengage from the output shaft.  
When this happens, the bit will stop turning.  
CAUTION:  
As soon as the torque limiter actuates, switch off the tool  
immediately. This will help prevent premature wear of the  
tool.  
Hole saws, core bits, diamond core bits, etc. cannot be  
used with this tool. They tend to pinch or catch easily in  
the hole. This will cause the torque limiter to actuate too  
frequently.  
ASSEMBLY  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before carrying out any work on the tool.  
003143  
Side grip (auxiliary handle)  
2
The side grip swings around to either side, allowing easy  
handling of the tool in any position. Loosen the side grip by  
turning it counterclockwise, swing it to the desired position  
and then tighten it by turning clockwise.  
1
1. Side grip  
2. Clamp screw  
Bit grease (optional accessory)  
Coat the bit shank head beforehand with a small amount of  
bit grease (about 0.5 - 1 g; 0.02 - 0.04 oz.). This chuck lubri-  
cation assures smooth action and longer service life.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
003150  
Installing or removing the bit  
Clean the bit shank and apply bit grease before installing the  
bit.  
2
1
1. Bit shank  
2. Bit grease  
003158  
Insert the bit into the tool. Turn the bit and push it in until it  
engages.  
If the bit cannot be pushed in, remove the bit. Pull the chuck  
cover down a couple of times. Then insert the bit again. Turn  
the bit and push it in until it engages.  
1
2
After installing, always make sure that the bit is securely held  
in place by trying to pull it out.  
1. Bit  
2. Chuck cover  
003163  
To remove the bit, pull the chuck cover down all the way and  
pull the bit out.  
1
2
1. Bit  
2. Chuck cover  
003181  
Depth gauge  
1
The depth gauge is convenient for drilling holes of uniform  
depth. Insert the depth gauge into the hole in the grip base.  
Adjust the depth gauge to the desired depth and then tighten  
the clamp screw to secure the depth gauge.  
2
NOTE:  
The depth gauge cannot be used at the position where  
the depth gauge strikes against the tool body.  
1. Clamp screw  
2. Depth gauge  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
003186  
Dust cup (optional accessory)  
Use the dust cup to prevent dust from falling over the tool  
and on yourself when performing overhead drilling opera-  
tions. Attach the dust cup to the bit as shown in the figure.  
The size of bits which the dust cup can be attached to is as  
follows.  
1
003187  
Bit diameter  
Dust cup 5 6 mm (1/4) - 14.5 mm (9/16)  
Dust cup 9 12 mm (15/32) - 16 mm (5/8)  
1. Dust cup  
Hammer drilling operation  
OPERATION  
Set the action mode changing knob to the  
symbol.  
Position the bit at the desired location for the hole, then pull  
the switch trigger. Do not force the tool. Light pressure gives  
best results. Keep the tool in position and prevent it from slip-  
ping away from the hole.  
Do not apply more pressure when the hole becomes clogged  
with chips or particles. Instead, run the tool at an idle, then  
remove the bit partially from the hole. By repeating this sev-  
eral times, the hole will be cleaned out and normal drilling  
may be resumed.  
CAUTION:  
There is a tremendous and sudden twisting force  
exerted on the tool/bit at the time of hole break-through,  
when the hole becomes clogged with chips and  
particles, or when striking reinforcing rods embedded in  
the concrete. Always use the side grip (auxiliary handle)  
and firmly hold the tool by both side grip and switch  
handle during operations. Failure to do so may result in  
the loss of control of the tool and potentially severe  
injury.  
002449  
Blow-out bulb (optional accessory)  
After drilling the hole, use the blow-out bulb to clean the dust  
out of the hole.  
1
1. Blow-out bulb  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
003219  
Drilling in wood or metal  
Use the optional drill chuck assembly. When installing it, refer  
to Installing or removing the bitdescribed on the previous  
page.  
Set the action mode changing knob to rotation only.  
1
You can drill up to 13 mm (1/2) diameter in metal and up to  
32 mm (1-1/4) diameter in wood.  
1. Drill chuck assembly  
CAUTION:  
Never use rotation with hammeringwhen the drill  
chuck assembly is installed on the tool. The drill chuck  
assembly may be damaged. Also, the drill chuck will  
come off when reversing the tool.  
Pressing excessively on the tool will not speed up the  
drilling. In fact, this excessive pressure will only serve to  
damage the tip of your bit, decrease the tool  
performance and shorten the service life of the tool.  
There is a tremendous twisting force exerted on the tool/  
bit at the time of hole breakthrough. Hold the tool firmly  
and exert care when the bit begins to break through the  
workpiece.  
A stuck bit can be removed simply by setting the  
reversing switch to reverse rotation in order to back out.  
However, the tool may back out abruptly if you do not  
hold it firmly.  
Always secure small workpieces in a vise or similar hold-  
down device.  
MAINTENANCE  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before attempting to perform inspection or  
maintenance.  
To maintain product SAFETY and RELIABILITY, repairs, car-  
bon brush inspection and replacement, any other mainte-  
nance or adjustment should be performed by Makita  
Authorized or Factory Service Centers, always using Makita  
replacement parts.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ACCESSORIES  
CAUTION:  
These accessories or attachments are recommended for  
use with your Makita tool specified in this manual. The  
use of any other accessories or attachments might  
present a risk of injury to persons. Only use accessory  
or attachment for its stated purpose.  
If you need any assistance for more details regarding these  
accessories, ask your local Makita service center.  
SDS-Plus Carbide-tipped bits  
SDS to A-Taper adapter  
Cotter (Drift key)  
Drill chuck assembly  
Drill chuck S13  
Chuck adapter  
Chuck key S13  
Bit grease  
Grip assembly  
Depth gauge  
Blow-out bulb  
Dust cup  
Dust extractor attachment  
Safety goggles  
Plastic carrying case  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memo  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stamp  
Timbre  
Makita Canada Inc.  
1950 Forbes Street,  
Whitby, Ontario  
L1N 7B7  
Fold  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Your answers to the following questions are appreciated.  
1.This product was purchased from?  
3. How did you first learn of Makita Power Tools?  
Hardware/lumber Store  
Tool Distributor  
Industrial Supply  
Other (  
Magazine/Newspaper  
From dealer  
Catalog  
Other (  
)
)
Store display  
2. Use of the product is intended for?  
4. Most favored points are?  
Construction trade  
Home maintenance  
Other (  
Design  
Makita Brand  
Power  
Industrial maintenance  
)
Features  
Size  
Other (  
)
Price  
5. Any comments?  
Certificate of Warranty  
Mail to Makita  
Date Purchased  
Model No.  
Serial No.  
Month  
Day  
Year 20  
Male Female  
Single  
Married  
Initial Last Name  
Street Address  
City  
Province  
Postal Code  
Under 19  
20-29  
30-39  
40-49  
Over 50  
AGE:  
Occupation:  
Dealer's Name & Address:  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Paste Paste Paste Paste Paste Paste  
Paste  
Paste  
Factory Service Centres  
Head Office:  
1950 Forbes St., Whitby, Ontario, L1N 7B7  
(905) 571 - 2200 1-800-263-3734  
Regional Office:  
11771 Hammersmith Way, Richmond  
B.C. V7A 5H6  
(604) 272 - 3104 1-800-663-0909  
Regional Office:  
6389 boul. Couture, St. Leonard, Quebec  
(Montreal)  
H1P 3J5  
(514) 323 - 1223 1-800-361-7049  
(902) 468 - 7064 1-888-625-4821  
Dartmouth:  
202 Brownlow Avenue  
Dartmouth, N.S., B3B 1T5  
Ville St. Laurent:  
(Montreal)  
1140 Rue Bégin, Ville St. Laurent, Quebec  
H4R 1X1  
(514) 745 - 5025 1-888-745-5025  
Les Saules:  
(Quebec)  
1200 St. Jean Baptiste, Unit 106, Les Saules,  
Quebec, G2E 5E8  
(418) 871 - 5720 1-800-663-5757  
Nepean:  
(Ottawa)  
210 Colonnade Road, Unit 11, Nepean,  
Ontario, K2E 7M1  
(613) 224 - 5022 1-888-560-2214  
Whitby:  
1950 Forbes St., Whitby, Ontario, L1N 7B7  
(905) 571 - 2200 1-800-263-3734  
London:  
317 Adelaide St. S., Unit 117, London,  
Ontario, N5Z 3L3  
(519) 686 - 3115 1-800-571-0899  
Mississauga:  
Calgary:  
6350 Tomken Rd., Unit 8, Mississauga,  
Ontario, L5T 1Y3  
(905) 670 - 7255 1-888-221-9811  
#8-6115 Fourth St. S.E., Calgary  
Alberta, T2H 2H9  
(403) 243 - 3995 1-800-267-0445  
Edmonton:  
Richmond:  
Coquitlam:  
Winnipeg:  
Saskatoon:  
11614-149 Street, Edmonton, Alberta,  
T5M 3R3  
(780) 455 - 6644 1-888-455-6644  
11771 Hammersmith Way, Richmond, B.C.,  
V7A 5H6  
(604) 272 - 3104 1-800-663-0909  
2131 Hartley Ave., #103  
Coquitlam, B.C. V3K 2Z3  
(604) 525 - 7434 1-800-266-7738  
1670 St. James Street, Winnipeg, Manitoba,  
R3H 0L3  
(204) 694 - 0402 1-800-550-5073  
206A-2750 Faithful Avenue Saskatoon,  
Saskatchewan, S7K 6M6  
(306) 931 - 0111 1-888-931-0111  
For the authorized service centre nearest you please refer to the local yellow pages directory under toolsor con-  
tact our customer service department (Tel) 1-800-263-3734  
CUSTOMER RECORD  
When you need service...  
DATE  
Explain the problem in a letter  
PURCHASED:  
Enclose the letter with the tool  
DEALERS NAME  
Package carefully and send prepaid  
& ADDRESS:  
to the nearest Makita factory or  
authorized service centre  
MODEL NO.:  
SERIAL NO.:  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAKITA LIMITED ONE YEAR WARRANTY  
Warranty Policy  
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from  
workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during  
this one year period, return the COMPLETE tool, freight prepaid, to one of Makitas Factory or Authorized Service Centres.  
If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace)  
without charge.  
This Warranty does not apply:  
where normal maintenance is required,  
repairs have been made or attempted by others,  
the tool has been abused, misused or improperly maintained,  
alterations have been made to the tool.  
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM  
THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS  
WARRANTY.  
The Makita Warranty is the only and the entire written warranty given by Makita for the Makita tools. No dealer or his agent  
or employee is authorized to extend or enlarge upon this warranty by any verbal or written statement or advertisement.”  
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES OF  
MERCHANTABILITYAND FITNESS FOR A SPECIFIC PURPOSE,AFTER THE ONE YEAR TERM OF THIS WARRANTY.  
This Warranty gives you specific rights. The provisions contained in this warranty are not intended to limit, modify, take away  
from, disclaim or exclude any warranties set forth in any provincial legislation. To the extent required by law, the provisions in  
any provincial or federal legislation with respect to warranties take precedence over the provisions in this warranty.”  
Makita Corporation  
3-11-8, Sumiyoshi-cho,  
Anjo, Aichi 446-8502 Japan  
883984-233  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Land Pride Lawn Mower zst40 User Manual
Lenovo Laptop Z475 User Manual
Lenovo Personal Computer TC A61 9120 User Manual
LevelOne Network Card FCS 1060 User Manual
LG Electronics Washer Dryer WM3431HS User Manual
Lightolier Indoor Furnishings 1102TF User Manual
Lincoln Automobile 2008 Mark LT User Manual
Manhattan Computer Products Computer Keyboard 155014 User Manual
McCulloch Blower 41AB225Q077 User Manual
Meade Binoculars Meade 8 x 42 20D CaptureView TM Integrated Binocular and Digital Camera User Manual