Battery-Powered
Pruning Shears
4604D
SPECIFICATIONS
Model
4604D
Max. cutting capacity .............................................................................................................30 mm in diameter
Overall length ......................................................................................................................................... 286 mm
Rated voltage ....................................................................................................................................... D.C. 24 V
Net weight
Shears .....................................................................................................................................................1.0 kg
Controller C4600 .....................................................................................................................................0.3 kg
Battery 4600 ............................................................................................................................................2.0 kg
Charging time ..................................................................................................................................Approx. 1 hr.
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge according to EPTA-Procedure 01/2003
Download from Www.Somanuals.com. All Manuals Search And Download.
20
19
22
21
9
10
12
14
16
23
24
17
11
13
15
26
27
25
28
27
3
Download from Www.Somanuals.com. All Manuals Search And Download.
29
23
23
29
30
17
18
20
22
24
31
26
24
19
23
32
33
21
33
24
23
4
Download from Www.Somanuals.com. All Manuals Search And Download.
25
END004-4
Symbols
The following show the symbols used for the equipment. Be sure that you understand their meaning before
use.
• Read instruction manual.
• Only for EU countries
Do not dispose of electric equipment or battery pack together with household waste mate-
rial!
Cd
Ni-MH
Li-ion
In observance of European Directive 2002/96/EC on waste electric and electronic equip-
ment, 2006/66/EC on batteries and accumulators and waste batteries and accumulators
and their implementation in accordance with national laws, electric equipment and battery
pack that have reached the end of their life must be collected separately and returned to
an environmentally compatible recycling facility.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
Explanation of general view
1
2
3
4
5
6
7
8
9
Charger DC4600
Charging light
Start button
Battery 4600
Charging plug
Charging connector
Restart button
Controller C4600
Switch
12 Waist belt
13 Pocket lid
14 Controller connector
15 Waist belt pocket
16 Suspenders
17 Holster
23 Upper shear blade
24 Lower shear blade
25 Branch
26 Hex wrench
27 Blade cover
28 Socket wrench
29 Blade holder
30 Magnet
18 Arm band
19 Connection cord
20 Female plug
21 Switch trigger
22 Lock-off lever
31 Brush
32 Machine oil
33 Diamond file
10 Buckle
11 Pilot lamp
11. Secure the work
SAFETY INSTRUCTIONS
– Use clamps or a vice to hold the work. It is safer
than using your hand and it frees both hands to
operate the tool.
WARNING! When using battery operated tools basic
safety precautions, including the following, should
be followed to reduce the risk of fire, leaking batter-
ies and personal injury: Read these instructions
before operating this product and save these instruc-
tions.
12. Do not over-reach
– Keep proper footing and balance at all times.
13. Maintain tools with care
– Keep cutting tools sharp and clean for better and
safer performance. Follow instructions for lubrica-
tion and changing accessories. Inspect tool cords
periodically and if damaged have repaired by an
authorized service facility.
For safe operation:
1. Keep work area clean
– Cluttered areas and benches invite injuries.
2. Consider the work environment
– Do not expose the tool to rain. Keep work area well
lit. Do not use tools in the presence of flammable
liquids or gases.
14. Disconnect tools
– Where the design permits, disconnect the tool
from its battery pack when not in use, before ser-
vicing and when changing accessories such as
blades, bits and cutters.
3. Keep children away
– Do not let visitors touch the tool. Keep visitors
away from work area.
4. Store batteries or idle tools
15. Remove adjusting keys and wrenches
– Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning it on.
16. Avoid unintentional starting
– Do not carry the tool with a finger on the switch.
17. Stay alert
– Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
18. Check damaged parts
– When not in use, tools and batteries should be
stored separately in a dry, high or locked up place,
out of reach of children.
– Ensure that battery terminals cannot be shorted by
other metal parts such as screws, nails, etc.
5. Do not force the tool
– It will do the job better and safer at the rate for
which it was intended.
6. Use the right tool
– Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
determine that it will operate properly and perform
its intended function. Check for alignment of mov-
ing parts, free running of moving parts, breakage
of parts, mounting and any other condition that
may affect its operation. A guard or other part that
is damaged should be properly repaired or
replaced by an authorized service facility unless
otherwise indicated in this instruction manual.
Have defective switches replaced by an authorized
service facility. Do not use the tool if the switch
does not turn it on and off.
– Do not force small tools or attachments to do the
job of a heavy duty tools. Do not use tools for pur-
poses not intended.
7. Dress properly
– Do not wear loose clothing or jewellery, they can
be caught in moving parts. Non-skid footwear is
recommended when working outdoors. Wear pro-
tecting hair covering to contain long hair.
8. Use protective equipment
– Use safety glasses and if the cutting operation is
dusty, a face or dust mask.
9. Connect dust extraction equipment
– If devices are provided for the connection of dust
extraction and collection ensure these are con-
nected and properly used.
19. Warning
– The use of any accessory or attachment, other
than recommended in this instruction manual or
the catalog, may present a risk of personal injury.
– Ensure that the battery pack is correct for the tool.
– Ensure that the outside surface of battery pack or
tool is clean and dry before plugging into charger.
10. Do not abuse the supply cord (if fitted)
– Never carry the tool by the cord or yank it to dis-
connect from the socket. Keep the cord away from
heat, oil and sharp edges.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
– Ensure that batteries are charged using the cor-
rect charger recommended by the manufacturer.
Incorrect use may result in a risk of electric shock,
overheating or leakage of corrosive liquid from the
battery.
5. Do not short the battery:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery in
a
container with
other metal objects such as nails, coins, etc.
(3) Do not expose battery to water or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
20. Have your tool repaired by a qualified person
– This tool is constructed in accordance with the rel-
evant safety requirements. Repairs should only be
carried out by qualified persons using original
spare parts, otherwise this may result in consider-
able danger to the user.
Always cover the battery terminals with the bat-
tery cover when the battery is not used.
6. Do not incinerate the Battery even if it is severely
damaged or is completely worn out. The battery
can explode in a fire.
21. Disposal of battery
– Ensure battery is disposed of safety as instructed
by the manufacturer.
7. Be careful not to drop, shake or strike battery.
8. Do not charge inside a box or container of any
kind. The battery must be placed in a well venti-
lated area during charging.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating instruc-
tions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
3. CAUTION — To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types
of batteries may burst causing personal injury
and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to per-
sons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
ADDITIONAL SAFETY RULES FOR BATTERY-
POWERED PRUNING SHEARS
1. This tool is for pruning branches. Do not use it
for any job except that for which it is intended.
2. Don’t use the tool or perform battery charging
operations in the rain.
3. Don’t leave the tool in rain or wet locations.
4. Keep bystanders well away from your work area.
5. Be careful not to catch foreign matter between
the blades. If the blades are jammed with foreign
matter, immediately switch off the tool and dis-
connect the battery from the tool. Then remove
the foreign matter from the blades.
6. Never hold the branch you are pruning with your
free hand. Keep your free hand away from the
cutting area. Never touch the blades, they are
very sharp and you may cut yourself.
7. Don’t force the tool to make it cut. You could slip
and injure yourself or cut something else unin-
tentionally.
8. Avoid cutting electrical wires that may be hid-
den.
9. Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
10. Do not disassemble charger or battery; take it to
a qualified serviceman when service or repair is
required. Incorrect reassembly may result in a
risk of electric shock or fire.
9. Always check the blades carefully before opera-
tion.
10. Handle the blades with extreme care to prevent
cuts or injury from the blades.
11. Disconnect the battery from the tool after each
use and before attempting to perform inspection
or maintenance.
11. To reduce risk of electric shock, unplug charger
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
12. When not in use, always keep the tool in its hol-
ster.
SAVE THESE INSTRUCTIONS.
ADDITIONAL SAFETY RULES FOR CHARGER
& BATTERY
1. Do not charge battery when it or air temperature
is below 10°C (50°F) or above 40°C (104°F).
2. Do not charge or leave battery in a location
exposed to direct sunlight.
3. Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
4. Do not allow anything to cover or clog the
charger vents.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Wearing arm band (Fig. 8)
OPERATING INSTRUCTIONS
Attach the arm band to your arm. When wearing it, slip
the connection cord through the arm band as shown in
Fig. 8 to keep it out of the way.
Charging (Fig. 1 & 2)
Charge the battery 4600 with the Makita charger
DC4600 before use. Plug the charger into the power
receptacle and connect the charging plug into the charg-
ing connector on the battery. Press the start button (red)
on the charger. The charging light will come on and
charging will begin. When the charging light goes out
after about one hour, the charging will be completed. If
the charging light goes out within one minute after press-
ing the start button, the battery is dead. Replace it with a
new one. After charging, disconnect the charging plug
from the battery and power receptacle.
Connecting connection cord to shears (Fig. 9)
Connect the female plug of the connection cord to the
shear connector and turn the screw clockwise to secure
the female plug in place.
NOTE:
• If you connect or disconnect the connection cord with
the controller switched on, the pilot lamp will blink red
and green alternately. When this occurs, the shears will
not start even if you pull the switch trigger. Switch off
the controller and then switch it on again to start the
shears. (Fig. 4)
CAUTION:
• Remove the controller from the battery when charging.
• Do not keep the start button depressed with tape, etc.
The circuit will not function properly and a malfunction
of the charger may result.
Switch action
CAUTION:
• Before connecting the battery to the shears, always
check to see that the switch trigger actuates properly
and returns to the “OFF” position when released.
• Do not pull the switch trigger without depressing the
lock-off lever. It can cause switch breakage.
• Use only Makita charger DC4600 to charge the battery
4600. The use of any other chargers may cause dam-
age to the battery.
• When you charge a new battery or a battery which has
not been used for a long period, it may not accept a full
charge. This is a normal condition and does not indi-
cate a problem. You can recharge the battery fully after
discharging it completely a couple of times.
Switch on the controller by pressing the upper (I) side of
the switch. The pilot lamp will start to blink green. Then
pull the switch trigger and release it once. The upper
shear blade will start to move up as soon as you release
the switch trigger and will stop at the highest (wide open)
position. In case that the upper shear blade has already
opened, it will keep that position with the first trigger
operation. The pilot lamp will remain green continuously.
From the next trigger operation, you can cut branches.
(Fig. 4)
Overcurrent relay (Fig. 2)
The overcurrent relay is built into the battery to prevent a
battery short-circuit. When the overcurrent relay actu-
ates, the battery cannot be used. Press the restart button
on the battery to use it again. If the overcurrent relay
actuates frequently, there may be something wrong with
the battery, charger, controller or shears themselves.
Send them to your dealer or a Makita Service Center to
have them inspected and/or repaired.
To prevent the switch trigger from being accidentally
pulled, a lock-off lever is provided. To start the shears,
depress the lock-off lever and pull the switch trigger. To
stop the shears, release the switch trigger. (Fig. 10)
When the switch trigger is pulled and held, the upper
shear blade will move down and stop at the closed posi-
tion. When the switch trigger is released, the upper shear
blade will move up and stop at the highest (wide open)
position. (Fig. 11)
Installing controller on battery (Fig. 3 & 4)
First, make sure that the controller is switched off. Install
the controller on the battery and fasten it with the buck-
les.
Connecting connection cord to controller
Connect the male plug of the connection cord to the con-
troller connector and turn the screw clockwise to secure
the male plug in place.
Putting shears in holster (Fig. 12)
Switch off the controller by pressing the lower (O) side of
the switch while keeping the switch trigger pulled. The
upper shear blade will stop at the closed position. Put the
shears in the holster with the upper shear blade at the
closed position.
Putting battery into waist belt pocket (Fig. 5 & 6)
After installing the controller on the battery, put the bat-
tery with the controller into your waist belt pocket so that
the controller connector will point toward your hand with
which you operate the shears. Then cover the battery
with the pocket lid to keep them from accidentally falling
out of your pocket during operation.
NOTE:
• Fasten the tool with holster belt.
Pruning operation (Fig. 13)
CAUTION:
• Never operate the shears in an awkward posture. This
may cause a serious injury.
• Never hold the branch you are pruning with your free
hand. Keep your free hand away from the cutting area.
The blades are very sharp and you may cut yourself.
Wearing waist belt (Fig. 6)
Attach a pair of suspenders on the waist belt. Wear the
waist belt and adjust the lengh of suspenders and waist
belt so that the battery will be positioned on your back at
waist height.
Installing holster (Fig. 7)
Install the holster on the waist belt as shown in Fig. 7. It
should be positioned on the side where your hand oper-
ates the shears.
Cut branches one by one as shown in Fig. 13. The maxi-
mum thickness of branches which can be cut with these
shears is about 30 mm. Maintain your proper footing and
balance at all times.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
After use, switch off the controller and disconnect the
connection cord from the shears and the controller. Store
the shears in dry, high or locked-up place – out of reach
of children.
Remove the upper shear blade from the blade holder. Be
careful not to allow any foreign matter to attach to the
magnet on the blade holder and do not damage it.
(Fig. 18)
Use the hex wrench provided to remove the two hex
socket head bolts which secure the lower shear blade.
Then remove the lower shear blade. (Fig. 19)
To install the shear blades, follow the removal procedures
in reverse. Do not remove grease around the gear.
Overload protecting mechanism
Both the shears and the controller are equipped with an
overload protecting mechanism. If the motor is locked for
more than three seconds, this mechanism will actuate to
stop the shears. Also, the pilot lamp on the controller will
start to blink red and green alternately. To resume opera-
tion, switch off the controller by pressing the lower (O)
side of the switch, then switch it on again.
MAINTENANCE
CAUTION:
• Always be sure that the controller is switched off and
the connection cord is disconected from the shears.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
NOTE:
• Do not operate the shears in such a way that this
mechanism actuates frequently. The motor may be
damaged.
Blade maintenance (Fig. 20 & 21)
Pilot lamp on controller (Fig. 4)
The pilot lamp will start to blink or remain green when the
controller is switched on (the upper (I) side of the switch
is pressed). If the pilot lamp indicates the following condi-
tions, proceed as follows.
1. If the pilot lamp blinks red and green alternately, the
overload protecting mechanism has been actuated
or the connection cord is not firmly connected.
Switch off the controller and do the following:
a) If the motor is locked for more than three
seconds, just switch on the controller.
NOTE:
• Before and after operation, check the shear blades
carefully.
After operation, clean off the blades with a stiff brush.
Then wipe the blades with a cloth and coat them with
machine oil.
CAUTION:
• Failure to perform blade maintenance may cause
excessive blade friction and shorten the operating time
per battery charge.
b) If the connection cord is not connected firmly,
connect the connection cord firmly and then
switch on the controller.
Sharpening blades
Upper shear blade
2. If the pilot lamp blinks red, the inside of the controller
is too hot. Switch off the controller and wait for a
while to cool it down. Then switch it on.
3. If the pilot lamp remains red continuously, the bat-
tery voltage is too low. Charge the battery.
4. If the pilot lamp is neither green or red:
a) The battery is completely discharged. Charge
the battery.
Apply the flat surface of the diamond file to the blade
edge. Push the diamond file in the direction of the arrow
to sharpen along the entire blade edge. Maintain the
same flat contact with the file consistently along the
entire blade edge. (Fig. 22)
Apply the flat surface of the diamond file lightly to the
reverse side of the blade. Move the diamond file in the
direction of the arrow to remove burrs. (Fig. 23)
b) The overcurrent relay has actuated. Press the
restart button.
Lower shear blade
Apply the round surface of the diamond file to the blade
edge. Push the diamond file in the direction of the arrow
to sharpen along the entire blade edge. (Fig. 24)
Apply the flat surface of the diamond file lightly to the
opposite side of the blade. Move the diamond file in the
direction of the arrow to remove burrs. (Fig. 25)
If the pilot lamp does not start to blink green even after
you perform the above procedures, there is something
wrong with the shears, connection cord, controller or bat-
tery. Switch off the controller and disconnect the connec-
tion cord from the shears and the controller. Remove the
controller from the battery. Send the shears, connection
cord, controller and battery to your dealer or a Makita
Service Center to have them inspected and/or repaired.
To maintain product safety and reliability, repairs, mainte-
nance or adjustment should be carried out by Makita
Authorized Service Center.
Replacing shear blades
CAUTION:
• Always be sure that the controller is switched off and
the connection cord is disconnected from the shears.
The shear blades can be replaced irrespective of the
upper shear blade position.
Use the hex wrench provided to remove the two hex
socket head bolts which secure the blade cover. (Fig. 14)
Remove the blade cover. (Fig. 15)
Use the socket wrench provided to remove the hex lock
nut. The flat washer will come off together with the hex
lock nut. (Fig. 16)
Remove the round head bolt, blade holder and upper
shear blade. (Fig. 17)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Makita Corporation
Anjo, Aichi, Japan
884249B8
IDE
Download from Www.Somanuals.com. All Manuals Search And Download.
|