Hammer Drill
20 mm (3/4”)
MODEL HP2010N
DOUBLE
INSULATION
I N S T R U C T I O N M A N U A L
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
w w w. m a k i t a t o o l s . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Avoid accidental starting. Be sure switch
is off before plugging in. Carrying tools with
your finger on the switch or plugging in tools
that have the switch on invites accidents.
Electrical Safety
4. Double insulated tools are equipped with
a polarized plug (one blade is wider than
the other.) This plug will fit in a polarized
outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified elec-
trician to install a polarized outlet. Do not
change the plug in any way. Double insula-
12. Remove adjusting keys or wrenches
before turning the tool on. A wrench or a
key that is left attached to a rotating part of
the tool may result in personal injury.
13. Do not overreach. Keep proper footing
and balance at all times. Proper footing and
balance enables better control of the tool in
unexpected situations.
tion
eliminates the need for the three wire
grounded power cord and grounded power
supply system.
5. Avoid body contact with grounded sur-
faces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.
14. Use safety equipment. Always wear eye
protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must
be used for appropriate conditions. Ordinary
eye or sun glasses are NOT eye protection.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
Tool Use and Care
15. Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand or
against your body is unstable and may lead
to loss of control.
7. Do not abuse the cord. Never use the cord
to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil,
sharp edges or moving parts. Replace
damaged cords immediately. Damaged
cords increase the risk of electric shock.
16. Do not force tool. Use the correct tool for
your application. The correct tool will do the
job better and safer at the rate for which it is
designed.
8. When operating a power tool outside, use
an outdoor extension cord marked “W-A”
or “W”. These cords are rated for outdoor
use and reduce the risk of electric shock.
17. Do not use tool if switch does not turn it
on or off. Any tool that cannot be controlled
with the switch is dangerous and must be
repaired.
Personal Safety
9. Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
18. Disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing the tool.
Such preventive safety measures reduce the
risk of starting the tool accidentally.
19. Store idle tools out of reach of children
and other untrained persons. Tools are
dangerous in the hands of untrained users.
10. Dress properly. Do not wear loose cloth-
ing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
20. Maintain tools with care. Keep cutting
tools sharp and clean. Properly maintained
tools with sharp cutting edges are less likely
to bind and are easier to control.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
21. Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tools
operation. If damaged, have the tool ser-
viced before using. Many accidents are
caused by poorly maintained tools.
SERVICE
23. Tool service must be performed only by
qualified repair personnel. Service or main-
tenance performed by unqualified personnel
could result in a risk of injury.
24. When servicing a tool, use only identical
replacement parts. Follow instructions in
the Maintenance section of this manual.
Use of unauthorized parts or failure to follow
Maintenance instructions may create a risk of
electric shock or injury.
22. Use only accessories that are recom-
mended by the manufacturer for your
model. Accessories that may be suitable for
one tool, may become hazardous when used
on another tool.
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. Table 1 shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num-
ber, the heavier the cord.
Table 1: Minimum gage for cord
Volts
120 V
Total length of cord in feet
Ampere Rating
25 ft.
50 ft.
100 ft.
150 ft.
More Than
Not More Than
AWG
0
6
10
12
6
18
18
16
14
16
16
16
12
16
14
14
14
12
12
10
12
16
Not Recommended
SPECIFIC SAFETY RULES
USB002-2
DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to hammer drill safety
rules. If you use this tool unsafely or incorrectly, you can suffer
serious personal injury.
1. Hold tools by insulated gripping surfaces
when performing an operation where the
cutting tool may contact hidden wiring or
its own cord. Contact with a “live” wire will
make exposed metal parts of the tool “live”
and shock the operator.
2. Always be sure you have a firm footing. Be
sure no one is below when using the tool in
high locations.
3. Hold the tool firmly with both hands.
Always use the side grip.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Keep hands away from rotating parts.
7. Some material contains chemicals which
may be toxic. Take caution to prevent dust
inhalation and skin contact. Follow mate-
rial supplier safety data.
5. Do not leave the tool running.
Operate the tool only when hand-held.
6. Do not touch the bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
SAVE THESE INSTRUCTIONS
WARNING:
MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONAL
DESCRIPTION
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
002457
Switch action
CAUTION:
1
3
2
•
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the “OFF”
position when released.
4
5
•
Switch can be locked in “ON” position for ease of
operator comfort during extended use. Apply caution
when locking tool in “ON” position and maintain firm
grasp on tool.
1. Speed control screw
2. Low
3. High
4. Switch trigger
5. Lock button
To start the tool, simply pull the switch trigger. Tool speed is
increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
To stop the tool from the locked position, pull the switch trig-
ger fully, then release it.
A speed control screw is provided so that maximum tool
speed can be limited (variable). Turn the speed control screw
clockwise for higher speed, and counterclockwise for lower
speed.
002411
Reversing switch action
This tool has a reversing switch to change the direction of
rotation. Move the reversing switch lever to the position for
clockwise rotation or the position for counterclockwise
rotation.
1
CAUTION:
•
•
Always check the direction of rotation before operation.
1. Reversing switch lever
Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation before
the tool stops may damage the tool.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
002853
Speed change
Two speed ranges can be preselected with the speed
change lever.
To change the speed, press the speed change lever and
slide it to the “L” position for low speed or the “H” position for
high speed. If the speed change lever does not slide easily,
turn the chuck slightly in either direction while sliding the
lever.
1
1. Change lever
Be sure that the speed change lever is set to the correct
position before operation. Use the right speed for your job.
CAUTION:
•
•
Always set the speed change lever fully to the correct
position. If you operate the tool with the speed change
lever positioned halfway, the tool may be damaged.
Do not use the speed change lever while the tool is
running. The tool may be damaged.
002854
Selecting the action mode
1
This tool has an action mode changing ring.
For rotation with hammering, turn the ring in the direction of
multiple arrow indication.
For rotation only, turn the ring in the direction of single arrow
indication.
CAUTION:
1. Change ring
•
•
Always turn the change ring fully to your desired mode
mark. If you operate the tool with the ring halfway, the
tool may be damaged.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
002458
Installing side grip (auxiliary handle)
Always use the side grip to ensure operating safety. Install
the side grip on the tool barrel. Then tighten the thumb screw
securely at the desired position. It may be swung 360° so as
to be secured at any position.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
002435
Installing or removing drill bit
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each of
the three holes and tighten clockwise. Be sure to tighten all
three chuck holes evenly.
1
To remove the bit, turn the chuck key counterclockwise in just
one hole, then loosen the chuck by hand.
1. Chuck key
002439
Depth gauge
The depth gauge is convenient for drilling holes of uniform
depth. Loosen the clamp screw and adjust the depth gauge
to the desired depth. After adjusting, tighten the clamp screw.
1
2
NOTE:
•
The depth gauge cannot be used at the position where
the depth gauge strikes against the tool body.
1. Depth gauge
2. Clamp screw
OPERATION
002445
Hammer drilling operation
CAUTION:
•
There is a tremendous and sudden twisting force
exerted on the tool/bit at the time of hole break-through,
when the hole becomes clogged with chips and
particles, or when striking reinforcing rods embedded in
the concrete. Always use the side grip (auxiliary handle)
and firmly hold the tool by both side grip and switch
handle during operations. Failure to do so may result in
the loss of control of the tool and potentially severe
injury.
Be sure to use a tungsten-carbide tipped bit.
Position the bit at the desired location for the hole, then pull
the switch trigger. Do not force the tool. Light pressure gives
best results. Keep the tool in position and prevent it from slip-
ping away from the hole.
Do not apply more pressure when the hole becomes clogged
with chips or particles. Instead, run the tool at an idle, then
remove the bit partially from the hole. By repeating this sev-
eral times, the hole will be cleaned out and normal drilling
may be resumed.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
002449
Blow-out bulb (optional accessory)
After drilling the hole, use the blow-out bulb to clean the dust
out of the hole.
1
1. Blow-out bulb
Drilling operation
CAUTION:
•
Pressing excessively on the tool will not speed up the
drilling. In fact, this excessive pressure will only serve to
damage the tip of your bit, decrease the tool
performance and shorten the service life of the tool.
•
•
There is a tremendous force exerted on the tool/bit at the
time of hole break through. Hold the tool firmly and exert
care when the bit begins to break through the workpiece.
A stuck bit can be removed simply by setting the
reversing switch to reverse rotation in order to back out.
However, the tool may back out abruptly if you do not
hold it firmly.
•
Always secure small workpieces in a vise or similar hold-
down device.
Drilling in wood
When drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide screw
makes drilling easier by pulling the bit into the workpiece.
Drilling in metal
To prevent the bit from slipping when starting a hole, make
an indentation with a center-punch and hammer at the point
to be drilled. Place the point of the bit in the indentation and
start drilling.
Use a cutting lubricant when drilling metals. The exceptions
are iron and brass which should be drilled dry.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
ACCESSORIES
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
To maintain product SAFETY and RELIABILITY, repairs, car-
bon brush inspection and replacement, any other mainte-
nance or adjustment should be performed by Makita
Authorized or Factory Service Centers, always using Makita
replacement parts.
CAUTION:
•
These accessories or attachments are recommended for
use with your Makita tool specified in this manual. The
use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding these
accessories, ask your local Makita service center.
•
•
•
•
•
•
Drill bits
Hammer drill bits
Blow-out bulb
Safety goggles
Chuck key
Steel carrying case
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
12
Download from Www.Somanuals.com. All Manuals Search And Download.
First-Class
Postage
Required
Post Office will
not deliver
without proper
postage.
Makita U.S.A., Inc.
14930 Northam Street
La Mirada, CA 90638-5753
Fold
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIL THIS PORTION
Your answers to the following questions are appreciated.
1.This product was purchased from:
3. How did you learn about this product:
Home Center
Other (
)
Magazine
Radio
Hardware/Lumber Store
Tool Distributor
From Dealer
Newspaper
Store Display
Catalog
Exhibition
From Friend
Previous Usage
Other (
Industrial Supply
Construction Supply
)
2. Use of the product is intended for:
4. Most favored points are:
Construction Trade
Industrial Maintenance
Home Maintenance
Hobby
Design
Repair Service
Durability
Power
Features
Size
Price
Other (
)
Other (
)
Makita Brand
5. Any comments:
DATE PURCHASED
MONTH
MODEL NO.
DAY
YEAR
SERIAL NO.
STATUS
SEX
Married Single
M
F
INTL.
LAST NAME / COMPANY NAME
STREET ADRESS
CITY
AREA
CODE
STATE
ZIP CODE
PHONE
40-49
Under 19
20-29
30-39
50-60
Over 60
AGE:
BE SURE TO COMPLETE THE CUSTOMER’S PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.
Please return this portion by facsimile or mail.
Facsimile No: (714) 522-8133
Download from Www.Somanuals.com. All Manuals Search And Download.
Paste
Paste
Paste
Paste
Paste
Paste
Paste
Paste
FACTORY SERVICE CENTERS
1-800-4-MAKITA
RETAIN THIS PORTION FOR YOUR RECORDS
ARIZONA
FLORIDA
MISSOURI
PENNSYLVANIA
1704 Babcock Blvd.
Pittsburgh, PA 15209
(412) 822-7370
3707 E. Broadway Rd., Ste. 6
Phoenix, AZ 85040
(602) 437-2850
750 East Sample Road
Pompano Beach, FL 33064
(954) 781-6333
9876 Watson Road
St. Louis, MO 63126-2221
(314) 909-9889
CALIFORNIA
GEORGIA
NEBRASKA
PUERTO RICO
41850 Christy St.
Fremont, CA 94538-5107
(510) 657-9881
4680 River Green Parkway NW
Duluth, GA 30096
(770) 476-8911
4129 S. 84th St.
Omaha, NE 68127
(402) 597-2925
200 Guayama St.
Hato Rey, PR 00917
(787) 250-8776
14930 Northam St.
La Mirada, CA 90638-5753
(714) 522-8088
ILLINOIS
NEVADA
3375 S. Decatur Blvd.
Suites. 22 - 24
Las Vegas, NV 89102
(702) 368-4277
TENNESSEE
1120 Elm Hill P.
Suile 170 Nashville, TN 372
(615) 248-3321
1450 Feehanville Dr.
Mt. Prospect, IL 60056-6011
(847) 297-3100
1970 Fulton Avenue
Sacramento, CA 95825
(916) 482-5197
MARYLAND
TEXAS
7674 Clairemont Mesa Blvd.
San Diego, CA 92111
(858) 278-4471
7397 Washington Boulevard,
Suite 104 Elkridge, MD 21075
(410) 796-4401
NEW JERSEY
12801 Stemmons Fwy Ste. 809
Farmers Branch, TX 75234
(972) 243-1150
251 Herrod Blvd.
Dayton, NJ 08810-1539
(609) 655-1212
16735 Saticoy St., Ste. 105
Van Nuys, CA 91406
(818) 782-2440
12701 Directors Dr.
Stafford, TX 77477-3701
(281) 565-8665
MASSACHUSETTS
232 Providence Hwy.
Westwood, MA 02090
(781) 461-9754
NEWYORK
4917 Genessee Street
Cheektowaga, NY 14225
(716) 685-9503
3453 IH-35 North, Ste. 101
San Antonio, TX 78219
(210) 228-0676
COLORADO
11839 E. 51st Ave.
Denver, CO 80239-2709
(303) 371-2850
MINNESOTA
6427 Penn Ave. South
Richfield, MN 55423
(612) 869-5199
OREGON
828 19th Avenue, N.W.
Portland, OR 97209
(503) 222-1823
WISCONSIN
Lincoln Plaza Shopping Ctr.
2245 S. 108th St. West Allis, WI
53227
(414) 541-4776
CUSTOMER’S RECORD
Date Purchased
When you need service: Send
complete tool (prepaid) to one
of the Makita Factory Service
Centers listed, or to an Authorized
Makita Service Center. Be sure
to attach a letter to the outside of
the carton detailing the problem
with your tool.
Dealer’s Name & Address
Model No.
Serial No.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles.
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of
defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of
Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective
workmanship or material, Makita will repair (or at our option, replace) without charge.
This Warranty does not apply where:
• repairs have been made or attempted by others:
• repairs are required because of normal wear and tear:
• the tool has been abused, misused or improperly maintained:
• alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING
AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF
“MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,” AFTER THE ONE YEAR TERM OF THIS
WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied
warranty lasts, so the above limitation may not apply to you.
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446-8502 Japan
883406I067
Download from Www.Somanuals.com. All Manuals Search And Download.
|