Makita Drill BDF460 User Manual

Cordless Driver Drill  
Equipped with Electric Brake  
MODEL BDF460  
002040  
I N S T R U C T I O N M A N U A L  
WARNING:  
For your personal safety, READ and UNDERSTAND before using.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAVE THESE INSTRUCTIONS  
9. Remove adjusting keys or wrenches  
Work Area  
before turning the tool on. A wrench or a  
key that is left attached to a rotating part of  
the tool may result in personal injury.  
1. Keep your work area clean and well lit.  
Cluttered benches and dark areas invite acci-  
dents.  
10. Do not overreach. Keep proper footing  
and balance at all times. Proper footing and  
balance enable better control of the tool in  
unexpected situations.  
2. Do not operate power tools in explosive  
atmospheres, such as in the presence of  
flammable liquids, gases, or dust. Power  
tools create sparks which may ignite the dust  
or fumes.  
11. Use safety equipment. Always wear eye  
protection. Dust mask, non-skid safety  
shoes, hard hat, or hearing protection must  
be used for appropriate conditions.  
3. Keep bystanders, children, and visitors  
away while operating a power tool. Dis-  
tractions can cause you to lose control.  
Tool Use and Care  
Electrical Safety  
12. Use clamps or other practical way to  
secure and support the workpiece to a  
stable platform. Holding the work by hand or  
against your body is unstable and may lead  
to loss of control.  
4. A battery operated tool with integral bat-  
teries or a separate battery pack must be  
recharged only with the specified charger  
for the battery. A charger that may be suit-  
able for one type of battery may create a risk  
of fire when used with another battery.  
13. Do not force tool. Use the correct tool for  
your application. The correct tool will do the  
job better and safer at the rate for which it is  
designed.  
5. Use battery operated tool only with specif-  
ically designated battery pack. Use of any  
other batteries may create a risk of fire.  
14. Do not use tool if switch does not turn it  
on or off. A tool that cannot be controlled  
with the switch is dangerous and must be  
repaired.  
Personal Safety  
6. Stay alert, watch what you are doing, and  
use common sense when operating a  
power tool. Do not use tool while tired or  
under the influence of drugs, alcohol, or  
medication. A moment of inattention while  
operating power tools may result in serious  
personal injury.  
15. Disconnect battery pack from tool or  
place the switch in the locked or off posi-  
tion before making any adjustments,  
changing accessories, or storing the tool.  
Such preventive safety measures reduce the  
risk of starting the tool accidentally.  
7. Dress properly. Do not wear loose cloth-  
ing or jewelry. Contain long hair. Keep  
your hair, clothing, and gloves away from  
moving parts. Loose clothes, jewelry, or long  
hair can be caught in moving parts.  
16. Store idle tools out of reach of children  
and other untrained persons. Tools are  
dangerous in the hands of untrained users.  
17. When battery pack is not in use, keep it  
away from other metal objects like: paper  
clips, coins, keys, nails, screws, or other  
small metal objects that can make a con-  
nection from one terminal to another.  
Shorting the battery terminals together may  
cause sparks, burns, or a fire.  
8. Avoid accidental starting. Be sure switch  
is in the locked or off position before  
inserting battery pack. Carrying tools with  
your finger on the switch or inserting the bat-  
tery pack into a tool with the switch on invites  
accidents.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
18. Maintain tools with care. Keep cutting  
tools sharp and clean. Properly maintained  
tools with sharp cutting edge are less likely to  
bind and are easier to control.  
one tool may create a risk of injury when  
used on another tool.  
SERVICE  
21. Tool service must be performed only by  
qualified repair personnel. Service or main-  
tenance performed by unqualified personnel  
may result in a risk of injury.  
19. Check for misalignment or binding of  
moving parts, breakage of parts, and any  
other condition that may affect the tool’s  
operation. If damaged, have the tool ser-  
viced before using. Many accidents are  
caused by poorly maintained tools.  
22. When servicing a tool, use only identical  
replacement parts. Follow instructions in  
the Maintenance section of this manual.  
Use of unauthorized parts or failure to follow  
Maintenance instructions may create a risk of  
shock or injury.  
20. Use only accessories that are recom-  
mended by the manufacturer for your  
model. Accessories that may be suitable for  
SPECIFIC SAFETY RULES  
USB022-2  
DO NOT let comfort or familiarity with product (gained from  
repeated use) replace strict adherence to cordless drill safety  
rules. If you use this tool unsafely or incorrectly, you can suffer  
serious personal injury.  
1. Hold tool by insulated gripping surfaces  
when performing an operation where the  
cutting tool may contact hidden wiring.  
Contact with a “live” wire will also make  
exposed metal parts of the tool “live” and  
shock the operator.  
5. Hold the tool firmly.  
6. Keep hands away from rotating parts.  
7. Do not leave the tool running. Operate the  
tool only when hand-held.  
8. Do not touch the drill bit or the workpiece  
immediately after operation; they may be  
extremely hot and could burn your skin.  
2. Be aware that this tool is always in an  
operating condition, because it does not  
have to be plugged into an electrical out-  
let.  
9. Some material contains chemicals which  
may be toxic. Take caution to prevent  
working dust inhalation and skin contact.  
Follow material supplier safety data.  
3. Always be sure you have a firm footing.  
4. Be sure no one is below when using the  
tool in high locations.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAVE THESE INSTRUCTIONS  
WARNING:  
MISUSE or failure to follow the safety rules stated in this  
instruction manual may cause serious personal injury.  
SYMBOLS  
USD301-1  
The followings show the symbols used for tool.  
V .......................volts  
....................no load speed  
n
˚
...................direct current  
.../min................revolutions or reciprocation per  
minute  
IMPORTANT SAFETY INSTRUCTIONS FOR  
CHARGER & BATTERY CARTRIDGE  
USC002-3  
1. SAVE THESE INSTRUCTIONS- This man-  
ual contains important safety and operat-  
ing instructions for battery charger.  
6. To reduce risk of damage to electric plug  
and cord, pull by plug rather than cord  
when disconnecting charger.  
2. Before using battery charger, read all  
instructions and cautionary markings on  
(1) battery charger, (2) battery, and (3)  
product using battery.  
7. Make sure cord is located so that it will  
not be stepped on, tripped over, or other-  
wise subjected to damage or stress.  
8. An extension cord should not be used  
unless absolutely necessary. Use of  
improper extension cord could result in a  
risk of fire and electric shock. If extension  
cord must be used, make sure:  
3. CAUTION - To reduce risk of injury, charge  
only MAKITA rechargeable batteries  
marked on the charger label. Other types  
of batteries may burst causing personal  
injury and damage.  
a. That pins on plug of extension cord  
are the same number, size, and shape  
as those of plug on charger;  
4. Do not expose charger to rain or snow.  
5. Use of an attachment not recommended  
or sold by the battery charger manufac-  
turer may result in a risk of fire, electric  
shock, or injury to persons.  
b. That extension cord is properly wired  
and in good electrical condition; and  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
c. That wire size is at least as large as  
the one specified in the table below.  
Table 1: RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS  
Length of Cord (Feet)  
AWG Size of Cord  
25  
18  
50  
18  
100  
18  
150  
16  
9. Do not operate charger with damaged  
cord or plug - replace them immediately.  
13. The battery charger is not intended for  
use by young children or infirm persons  
without supervision.  
10. Do not operate charger if it has received a  
sharp blow, been dropped, or otherwise  
damaged in any way; take it to a qualified  
serviceman.  
14. Young children should be supervised to  
ensure that they do not play with the bat-  
tery charger.  
11. Do not disassemble charger or battery  
cartridge; take it to a qualified serviceman  
when service or repair is required. Incor-  
rect reassembly may result in a risk of  
electric shock or fire.  
15. If operating time has become excessively  
shorter, stop operating immediately. It  
may result in a risk of overheating, possi-  
ble burns and even an explosion.  
16. If electrolyte gets into your eyes, rinse  
them out with clear water and seek medi-  
cal attention right away. It may result in  
loss of your eyesight.  
12. To reduce risk of electric shock, unplug  
charger from outlet before attempting any  
maintenance or cleaning. Turning off con-  
trols will not reduce this risk.  
ADDITIONAL SAFETY RULES FOR CHARGER &  
BATTERY CARTRIDGE  
1. Do not charge Battery Cartridge when  
temperature is BELOW 10°C (50°F) or  
ABOVE 40°C (104°F).  
(3) Do not expose battery cartridge to  
water or rain.  
A battery short can cause a large current  
flow, overheating, possible burns and  
even a breakdown.  
2. Do not attempt to use a step-up trans-  
former, an engine generator or DC power  
receptacle.  
5. Do not store the tool and Battery Car-  
tridge in locations where the temperature  
may reach or exceed 50°C (122°F).  
3. Do not allow anything to cover or clog the  
charger vents.  
4. Do not short the battery cartridge:  
6. Do not incinerate the Battery Cartridge  
even if it is severely damaged or is com-  
pletely worn out. The battery cartridge can  
explode in a fire.  
(1) Do not touch the terminals with any  
conductive material.  
(2) Avoid storing battery cartridge in a  
container with other metal objects  
such as nails, coins, etc.  
7. Be careful not to drop, shake or strike bat-  
tery.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Do not charge inside a box or container of  
any kind. The battery must be placed in a  
well ventilated area during charging.  
SAVE THESE INSTRUCTIONS  
SYMBOLS  
The following show the symbols used for the charger. Be sure that you understand their  
meaning before use.  
.......... Ready to charge  
.............Charging  
...........Delay charge (Cooling)  
........Defective battery  
....Conditioning  
.............Charging complete  
...........Cooling abnormality  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
FUNCTIONAL  
DESCRIPTION  
CAUTION:  
Always be sure that the tool is switched off and the  
battery cartridge is removed before adjusting or  
checking function on the tool.  
002054  
Installing or removing battery cartridge  
Always switch off the tool before insertion or removal of  
the battery cartridge.  
1
To remove the battery cartridge, withdraw it from the tool  
while sliding the button on the side of the cartridge.  
2
3
To insert the battery cartridge, align the tongue on the  
battery cartridge with the groove in the housing and slip  
it into place. Always insert it all the way until it locks in  
place with a little click. If you can see the red part on the  
upper side of the button, it is not locked completely.  
Insert it fully until the red part cannot be seen. If not, it  
may accidentally fall out of the tool, causing injury to you  
or someone around you.  
1. Red part  
2. Button  
3. Battery cartridge  
Do not use force when inserting the battery cartridge. If  
the cartridge does not slide in easily, it is not being  
inserted correctly.  
001336  
Charging  
2
1. Plug the battery charger into the proper AC voltage  
source. Two charging lights will flash in green color  
repeatedly.  
1
3
2. Insert the battery cartridge into charger until it stops  
adjusting to the guide of charger. Terminal cover of  
charger can be opened with inserting and closed with  
pulling out the battery cartridge.  
4
1. Terminal cover  
2. Battery cartridge  
3. Charging light  
4. Battery charger  
3. When the battery cartridge is inserted, the charging light  
color will change from green to red and charging will  
begin. The charging light will keep lighting up lit steadily  
during charging. One red charging light indicates  
charged condition in 0 - 80% and two red ones indicates  
80 - 100%.  
4. With finish of charge, the charging lights will change  
from two red ones to two green ones.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. If you leave the battery cartridge in the charger after the  
charging cycle is complete, the charger will switch into  
its trickle charge (maintenance charge)mode which  
will last approximately 24 hours.  
6. After charging, unplug the charger from the power  
source.  
NOTE:  
The battery charger is for charging Makita battery  
cartridge. Never use it for other purposes or for other  
manufacturers batteries.  
When you charge a new battery cartridge or a battery  
cartridge which has not been used for a long period of  
time, it may not accept a full charge. This is a normal  
condition and does not indicate a problem. You can  
recharge the battery cartridge fully after discharging it  
completely and recharging a couple of times.  
If you charge a battery cartridge from a just operated  
tool or battery cartridge which has been left in a location  
exposed to direct sunlight for a long time, the charging  
light may flash in red color. If this occurs, wait for a while.  
Charging will begin after the battery cartridge is cooled  
by the cooling fan installed in the charger. (DC24SA  
only) When the temperature on battery is more than  
approx. 70°C, two charging lights may flash in red color,  
and when approx. 50°C - 70°C, one charging light in red  
color.  
If the charging light flashes alternately in green and red  
color, charging is not possible. The terminals on the  
charger or battery cartridge are clogged with dust or the  
battery cartridge is worn out or damaged.  
Cooling system (DC24SA only)  
This charger is equipped with cooling fan for heated  
battery in order to enable the battery to prove its own  
performance. Sound of cooling air comes out during  
cooling, which means no trouble on the charger.  
Yellow light will flash for warning in the following cases.  
- Trouble on cooling fan  
- Incomplete cool down of battery, such as, being  
clogged with dust  
The battery can be charged in spite of the yellow  
warning light. But the charging time will be longer than  
usual in this case.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Check the sound of cooling fan, vent on the charger and  
battery, which can be sometime clogged with dust.  
The cooling system is in order although no sound of  
cooling fan comes out, if the yellow warning light will not  
flash.  
Always keep clean the vent on charger and battery for  
cooling.  
The products should be sent to repair or maintenance, if  
the yellow warning light will frequently flash.  
Conditioning charge (DC24SA only)  
Conditioning charge can extend the life of battery by auto-  
matically searching the optimum charging condition for the  
batteries in every situations.  
The battery employed in the following conditions repeatedly,  
will be worn out shortly, and yellow warning light may flash.  
1. Recharge of battery with its high temperature  
2. Recharge of battery with its low temperature  
3. Recharge of full charged battery  
4. Over-discharge of battery (continue to discharge battery  
in spite of down of power.)  
The charging time of such battery is longer than usual.  
Trickle charge (Maintenance charge)  
If you leave the battery cartridge in the charger to prevent  
spontaneous discharging after full charge, the charger will  
switch into its trickle charge (maintenance charge)mode  
and keep the battery cartridge fresh and fully charged.  
Tips for maintaining maximum battery life  
1. Charge the battery cartridge before completely dis-  
charged.  
Always stop tool operation and charge the battery car-  
tridge when you notice less tool power.  
2. Never recharge a fully charged battery cartridge.  
Overcharging shortens the battery service life.  
3. Charge the battery cartridge with room temperature at  
10°C - 40°C (50°F - 104°F).  
Let a hot battery cartridge cool down before charging it.  
4. Charge the Nickel Metal Hydride battery cartridge when  
you do not use it for more than six months.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
002080  
Switch action  
CAUTION:  
Before inserting the battery cartridge into the tool,  
always check to see that the switch trigger actuates  
properly and returns to the OFFposition when  
released.  
1
To start the tool, simply pull the switch trigger. Tool speed is  
increased by increasing pressure on the switch trigger.  
Release the switch trigger to stop.  
1. Switch trigger  
Electric brake  
This tool is equipped with an electric brake. If the tool consis-  
tently fails to quickly stop after switch trigger release, have  
tool serviced at a Makita service center.  
002090  
Reversing switch action  
This tool has a reversing switch to change the direction of  
rotation. Depress the reversing switch lever from the A side  
for clockwise rotation or from the B side for counterclockwise  
rotation.  
1
A
B
When the reversing switch lever is in the neutral position, the  
switch trigger cannot be pulled.  
1. Reversing switch lever  
CAUTION:  
Always check the direction of rotation before operation.  
Use the reversing switch only after the tool comes to a  
complete stop. Changing the direction of rotation before  
the tool stops may damage the tool.  
When not operating the tool, always set the reversing  
switch lever to the neutral position.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
002097  
Speed change  
To change the speed, first switch off the tool and then slide  
the speed change lever to the IIside for high speed or I”  
side for low speed. Be sure that the speed change lever is  
set to the correct position before operation. Use the right  
speed for your job.  
1
2
3
CAUTION:  
1. Low speed  
Always set the speed change lever fully to the correct  
position. If you operate the tool with the speed change  
lever positioned halfway between the Iside and II”  
side, the tool may be damaged.  
2. High speed  
3. Speed change lever  
Do not use the speed change lever while the tool is  
running. The tool may be damaged.  
002105  
Adjusting the fastening torque  
The fastening torque can be adjusted in 17 steps by turning  
the adjusting ring so that its graduations are aligned with the  
pointer on the tool body. The fastening torque is minimum  
when the number 1 is aligned with the pointer, and maximum  
2
3
when the  
marking is aligned with the pointer.  
1
4
The clutch will slip at various torque levels when set at the  
number 1 to 16. The clutch is designed not to slip at the  
marking.  
1. Graduations  
2. Adjusting ring  
3. Drill marking  
4. Pointer  
Before actual operation, drive a trial screw into your material  
or a piece of duplicate material to determine which torque  
level is required for a particular application.  
NOTE:  
The adjusting ring does not lock when the pointer is  
positioned only halfway between the graduations.  
Do not operate the tool with the adjusting ring set  
between the number 16 and the  
may be damaged.  
marking. The tool  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
CAUTION:  
Always be sure that the tool is switched off and the  
battery cartridge is removed before carrying out any  
work on the tool.  
002109  
Installing side grip (auxiliary handle)  
CAUTION:  
2
1
Always be sure that the side grip is installed securely  
before operation.  
3
Always use the side grip to ensure operating safety. Install  
the side grip so that the teeth on the grip fit in between the  
protrusions on the tool barrel.  
Then tighten the grip by turning clockwise at the desired  
position. It may be swung 360° so as to be secured at any  
position.  
1. Grip base  
2. Teeth  
3. Side grip  
002121  
Installing or removing driver bit or drill bit  
Turn the sleeve counterclockwise to open the chuck jaws.  
Place the bit in the chuck as far as it will go. Turn the sleeve  
clockwise to tighten the chuck.  
1
2
To remove the bit, turn the sleeve counterclockwise.  
1. Tighten  
2. Sleeve  
002122  
When not using the driver bit, keep it in the bit holders. Bits  
45 mm (1-3/4) long can be kept there.  
2
1
1. Bit  
2. Bit holder  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
002127  
Adjustable depth rod  
1
The adjustable depth rod is used to drill holes of uniform  
depth. Loosen the clamp screw, set to desired position, then  
tighten the clamp screw.  
2
1. Depth rod  
2. Clamp screw  
OPERATION  
CAUTION:  
Always insert the battery cartridge all the way until it  
locks in place. If you can see the red part on the upper  
side of the button, it is not locked completely. Insert it  
fully until the red part cannot be seen. If not, it may  
accidentally fall out of the tool, causing injury to you or  
someone around you.  
When operating overhead, always make sure the battery  
cartridge is locked securely so that it will not be fallen out  
of the tool. If not, it may accidentally fall out of the tool,  
causing injury to you or someone around you.  
002135  
Screwdriving operation  
Place the point of the driver bit in the screw head and apply  
pressure to the tool. Start the tool slowly and then increase  
the speed gradually. Release the switch trigger as soon as  
the clutch cuts in.  
NOTE:  
Make sure that the driver bit is inserted straight in the  
screw head, or the screw and/or bit may be damaged.  
When driving wood screws, predrill pilot holes to make  
driving easier and to prevent splitting of the workpiece.  
See the chart.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Nominal diameter of  
wood screw (mm)  
3.1 (1/8)  
Recommended size  
of pilot hole (mm)  
2.0 - 2.2 (5/64- 3/32)  
2.2 - 2.5 (3/32- 3/32)  
2.5 - 2.8 (3/32- 7/64)  
2.9 - 3.2 (7/64- 1/8)  
3.1 - 3.4 (1/8- 9/64)  
3.3 - 3.6 (1/8- 9/64)  
3.7 - 3.9 (9/64- 5/32)  
4.0 - 4.2 (5/32- 11/64)  
4.2 - 4.4 (11/64- 11/64)  
3.5 (9/64)  
3.8 (5/32)  
4.5 (11/64)  
4.8 (3/16)  
5.1 (13/64)  
5.5 (7/32)  
5.8 (7/32)  
6.1 (15/64)  
If the tool is operated continuously until the battery  
cartridge has discharged, allow the tool to rest for 15  
minutes before proceeding with a fresh battery.  
Drilling operation  
First, turn the adjusting ring so that the pointer points to the  
marking. Then proceed as follows.  
Drilling in wood  
When drilling in wood, the best results are obtained with  
wood drills equipped with a guide screw. The guide screw  
makes drilling easier by pulling the bit into the workpiece.  
Drilling in metal  
To prevent the bit from slipping when starting a hole, make  
an indentation with a center-punch and hammer at the point  
to be drilled. Place the point of the bit in the indentation and  
start drilling.  
Use a cutting lubricant when drilling metals. The exceptions  
are iron and brass which should be drilled dry.  
CAUTION:  
Pressing excessively on the tool will not speed up the  
drilling. In fact, this excessive pressure will only serve to  
damage the tip of your bit, decrease the tool  
performance and shorten the service life of the tool.  
There is a tremendous force exerted on the tool/bit at the  
time of hole break through. Hold the tool firmly and exert  
care when the bit begins to break through the workpiece.  
A stuck bit can be removed simply by setting the  
reversing switch to reverse rotation in order to back out.  
However, the tool may back out abruptly if you do not  
hold it firmly.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Always secure small workpieces in a vise or similar hold-  
down device.  
If the tool is operated continuously until the battery  
cartridge has discharged, allow the tool to rest for 15  
minutes before proceeding with a fresh battery.  
MAINTENANCE  
CAUTION:  
Always be sure that the tool is switched off and the  
battery cartridge is removed before attempting to  
perform inspection or maintenance.  
001145  
Replacing carbon brushes  
Remove and check the carbon brushes regularly. Replace  
when they wear down to the limit mark. Keep the carbon  
brushes clean and free to slip in the holders. Both carbon  
brushes should be replaced at the same time. Use only iden-  
tical carbon brushes.  
1
1
1. Limit mark  
002141  
Use a screwdriver to remove the brush holder caps. Take out  
the worn carbon brushes, insert the new ones and secure  
the brush holder caps.  
After replacing brushes, insert the battery cartridge into the  
tool and break in brushes by running tool with no load for  
about 1 minute. Then check the tool while running and elec-  
tric brake operation when releasing the switch trigger. If elec-  
tric brake is not working well, ask your local Makita service  
center for repair.  
2
1. Brush holder cap  
2. Screwdriver  
To maintain product SAFETY and RELIABILITY, repairs, any  
other maintenance or adjustment should be performed by  
Makita Authorized or Factory Service Centers, always using  
Makita replacement parts.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN0001-1  
Recycling the Battery  
The only way to dispose of a Makita battery is to recycle it.  
The law prohibits any other method of disposal.  
To recycle the battery:  
1. Remove the battery from the tool.  
Ni-Cd  
2. a) Take the battery to your nearest Makita Factory Ser-  
vice Center  
or  
b) Take the battery to your nearest Makita Authorized  
Service Center or Distributor that has been desig-  
nated as a Makita battery recycling location.  
Call your nearest Makita Service Center or Distributor to  
determine the location that provides Makita battery recycling.  
See your local Yellow Pages under Tools-Electric.  
ACCESSORIES  
CAUTION:  
These accessories or attachments are recommended for  
use with your Makita tool specified in this manual. The  
use of any other accessories or attachments might  
present a risk of injury to persons. Only use accessory  
or attachment for its stated purpose.  
If you need any assistance for more details regarding these  
accessories, ask your local Makita service center.  
Drill bits  
Screw bits  
Grip assembly  
Depth rod  
Plastic carrying case  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memo  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memo  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memo  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stamp  
Timbre  
Makita Canada Inc.  
1950 Forbes Street,  
Whitby, Ontario  
L1N 7B7  
Fold  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Your answers to the following questions are appreciated.  
1.This product was purchased from?  
3. How did you first learn of Makita Power Tools?  
Hardware/lumber Store  
Tool Distributor  
Industrial Supply  
Other (  
Magazine/Newspaper  
From dealer  
Catalog  
Other (  
)
)
Store display  
2. Use of the product is intended for?  
4. Most favored points are?  
Construction trade  
Home maintenance  
Other (  
Design  
Makita Brand  
Power  
Industrial maintenance  
)
Features  
Size  
Other (  
)
Price  
5. Any comments?  
Certificate of Warranty  
Mail to Makita  
Date Purchased  
Model No.  
Serial No.  
Month  
Day  
Year 20  
Male Female  
Single  
Married  
Initial Last Name  
Street Address  
City  
Province  
Postal Code  
Under 19  
20-29  
30-39  
40-49  
Over 50  
AGE:  
Occupation:  
Dealer's Name & Address:  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Paste Paste Paste Paste Paste Paste  
Paste  
Paste  
Factory Service Centres  
Head Office:  
1950 Forbes St., Whitby, Ontario, L1N 7B7  
(905) 571 - 2200 1-800-263-3734  
Regional Office:  
11771 Hammersmith Way, Richmond  
B.C. V7A 5H6  
(604) 272 - 3104 1-800-663-0909  
Regional Office:  
(Montreal)  
6389 boul. Couture, St. Leonard, Quebec  
H1P 3J5  
(514) 323 - 1223 1-800-361-7049  
Dartmouth:  
202 Brownlow Avenue  
Dartmouth, N.S., B3B 1T5  
(902) 468 - 7064 1-888-625-4821  
Ville St. Laurent:  
(Montreal)  
1140 Rue Bégin, Ville St. Laurent, Quebec  
H4R 1X1  
(514) 745 - 5025 1-888-745-5025  
Les Saules:  
(Quebec)  
1200 St. Jean Baptiste, Unit 106, Les Saules,  
Quebec, G2E 5E8  
(418) 871 - 5720 1-800-663-5757  
Nepean:  
(Ottawa)  
203 Colonnade Road, Unit #6, Nepean,  
Ontario K2E 7K3  
(613) 224 - 5022 1-888-560-2214  
Whitby:  
1950 Forbes St., Whitby, Ontario, L1N 7B7  
(905) 571 - 2200 1-800-263-3734  
London:  
317 Adelaide St. S., Unit 117, London,  
Ontario, N5Z 3L3  
(519) 686 - 3115 1-800-571-0899  
Mississauga:  
Calgary:  
6350 Tomken Rd., Unit 8, Mississauga,  
Ontario, L5T 1Y3  
(905) 670 - 7255 1-888-221-9811  
#8-6115 Fourth St. S.E., Calgary  
Alberta, T2H 2H9  
(403) 243 - 3995 1-800-267-0445  
Edmonton:  
Richmond:  
Coquitlam:  
Winnipeg:  
Saskatoon:  
11614-149 Street, Edmonton, Alberta,  
T5M 3R3  
(780) 455 - 6644 1-888-455-6644  
11771 Hammersmith Way, Richmond, B.C.,  
V7A 5H6  
(604) 272 - 3104 1-800-663-0909  
2131 Hartley Ave., #103  
Coquitlam, B.C. V3K 2Z3  
(604) 525 - 7434 1-800-266-7738  
1670 St. James Street, Winnipeg, Manitoba,  
R3H 0L3  
(204) 694 - 0402 1-800-550-5073  
206A-2750 Faithful Avenue Saskatoon,  
Saskatchewan, S7K 6M6  
(306) 931 - 0111 1-888-931-0111  
For the authorized service centre nearest you please refer to the local yellow pages directory under toolsor con-  
tact our customer service department (Tel) 1-800-263-3734  
CUSTOMER RECORD  
When you need service...  
DATE  
Explain the problem in a letter  
PURCHASED:  
Enclose the letter with the tool  
DEALERS NAME  
Package carefully and send prepaid  
& ADDRESS:  
to the nearest Makita factory or  
authorized service centre  
MODEL NO.:  
SERIAL NO.:  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAKITA LIMITED ONE YEAR WARRANTY  
Warranty Policy  
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from  
workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during  
this one year period, return the COMPLETE tool, freight prepaid, to one of Makitas Factory or Authorized Service Centres.  
If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace)  
without charge.  
This Warranty does not apply:  
where normal maintenance is required,  
repairs have been made or attempted by others,  
the tool has been abused, misused or improperly maintained,  
alterations have been made to the tool.  
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM  
THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS  
WARRANTY.  
The Makita Warranty is the only and the entire written warranty given by Makita for the Makita tools. No dealer or his agent  
or employee is authorized to extend or enlarge upon this warranty by any verbal or written statement or advertisement.”  
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES OF  
MERCHANTABILITYAND FITNESS FOR A SPECIFIC PURPOSE,AFTER THE ONE YEAR TERM OF THIS WARRANTY.  
This Warranty gives you specific rights. The provisions contained in this warranty are not intended to limit, modify, take away  
from, disclaim or exclude any warranties set forth in any provincial legislation. To the extent required by law, the provisions in  
any provincial or federal legislation with respect to warranties take precedence over the provisions in this warranty.”  
Makita Corporation  
3-11-8, Sumiyoshi-cho,  
Anjo, Aichi 446-8502 Japan  
884325A236  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Land Pride Brush Cutter RCP2660 User Manual
Lightolier Indoor Furnishings 1101FDM User Manual
Link electronic Portable Generator 812 OP E User Manual
Lochinvar Boiler 10 13 15 User Manual
Lumens Technology Camera Accessories PS760 User Manual
Magic Chef Griddle MCSG19B1 User Manual
Magnadyne Home Security System M7a User Manual
Manitowoc Ice Ice Maker 7603323 User Manual
M Audio Network Router RAD 050503 User Manual
Microsoft Computer Accessories 5908400 User Manual