Cordless Driver Drill
Equipped with Electric Brake
MODEL 6217D
MODEL 6237D
MODEL 6317D
MODEL 6337D
MODEL 6347D
I N S T R U C T I O N M A N U A L
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
w w w. m a k i t a t o o l s . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
(FOR All BATTERY OPERATED TOOLS)
WARNING:
USA003-1
Read and understand all instructions. Failure to follow all
instructions listed below, may result in electric shock, fire and/or
serious personal injury.
SAVE THESE INSTRUCTIONS
under the influence of drugs, alcohol, or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
Work Area
1. Keep your work area clean and well lit.
Cluttered benches and dark areas invite acci-
dents.
7. Dress properly. Do not wear loose cloth-
ing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power
tools create sparks which may ignite the dust
or fumes.
8. Avoid accidental starting. Be sure switch
is in the locked or off position before
inserting battery pack. Carrying tools with
your finger on the switch or inserting the bat-
tery pack into a tool with the switch on invites
accidents.
3. Keep bystanders, children, and visitors
away while operating a power tool. Distrac-
tions can cause you to lose control.
Electrical Safety
4. A battery operated tool with integral bat-
teries or a separate battery pack must be
recharged only with the specified charger
for the battery. A charger that may be suit-
able for one type of battery may create a risk
of fire when used with another battery.
9. Remove adjusting keys or wrenches
before turning the tool on. A wrench or a
key that is left attached to a rotating part of
the tool may result in personal injury.
10. Do not overreach. Keep proper footing
and balance at all times. Proper footing and
balance enable better control of the tool in
unexpected situations.
5. Use battery operated tool only with specif-
ically designated battery pack. Use of any
other batteries may create a risk of fire.
11. Use safety equipment. Always wear eye
protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must
be used for appropriate conditions.
Personal Safety
6. Stay alert, watch what you are doing, and
use common sense when operating
power tool. Do not use tool while tired or
a
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Shorting the battery terminals together may
cause sparks, burns, or a fire.
Tool Use and Care
12. Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand or
against your body is unstable and may lead
to loss of control.
18. Maintain tools with care. Keep cutting
tools sharp and clean. Properly maintained
tools with sharp cutting edge are less likely to
bind and are easier to control.
19. Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tool’s
operation. If damaged, have the tool ser-
viced before using. Many accidents are
caused by poorly maintained tools.
13. Do not force tool. Use the correct tool for
your application. The correct tool will do the
job better and safer at the rate for which it is
designed.
14. Do not use tool if switch does not turn it
on or off. A tool that cannot be controlled
with the switch is dangerous and must be
repaired.
20. Use only accessories that are recom-
mended by the manufacturer for your
model. Accessories that may be suitable for
one tool may create a risk of injury when
used on another tool.
15. Disconnect battery pack from tool or
place the switch in the locked or off posi-
tion before making any adjustments,
changing accessories, or storing the tool.
Such preventive safety measures reduce the
risk of starting the tool accidentally.
SERVICE
21. Tool service must be performed only by
qualified repair personnel. Service or main-
tenance performed by unqualified personnel
may result in a risk of injury.
16. Store idle tools out of reach of children
and other untrained persons. Tools are
dangerous in the hands of untrained users.
22. When servicing a tool, use only identical
replacement parts. Follow instructions in
the Maintenance section of this manual.
Use of unauthorized parts or failure to follow
Maintenance instructions may create a risk of
shock or injury.
17. When battery pack is not in use, keep it
away from other metal objects like: paper
clips, coins, keys, nails, screws, or other
small metal objects that can make a con-
nection from one terminal to another.
SPECIFIC SAFETY RULES
USB022-2
DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to cordless driver safety
rules. If you use this tool unsafely or incorrectly, you can suffer
serious personal injury.
1. Hold tool by insulated gripping surfaces
when performing an operation where the
cutting tool may contact hidden wiring.
2. Be aware that this tool is always in an
operating condition, because it does not
have to be plugged into an electrical out-
let.
Contact with
a
“live” wire will also make
exposed metal parts of the tool “live” and
shock the operator.
3. Always be sure you have a firm footing.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Be sure no one is below when using the
tool in high locations.
8. Do not touch the drill bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
5. Hold the tool firmly.
9. Some material contains chemicals which
may be toxic. Take caution to prevent
working dust inhalation and skin contact.
Follow material supplier safety data.
6. Keep hands away from rotating parts.
7. Do not leave the tool running. Operate the
tool only when hand-held.
SAVE THESE INSTRUCTIONS
WARNING:
MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
SYMBOLS
USD301-1
The followings show the symbols used for tool.
V ....................... volts
....................no load speed
n
˚
................... direct current
.../min................revolutions or reciprocation per
minute
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
USC001-3
1. SAVE THESE INSTRUCTIONS - This man-
ual contains important safety and operat-
ing instructions for battery charger.
3. CAUTION - To reduce risk of injury, charge
only MAKITA rechargeable batteries
marked on the charger label. Other types
of batteries may burst causing personal
injury and damage.
2. Before using battery charger, read all
instructions and cautionary markings on
(1) battery charger, (2) battery, and (3)
product using battery.
4. Do not expose charger to rain or snow.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Use of an attachment not recommended
or sold by the battery charger manufac-
turer may result in a risk of fire, electric
shock, or injury to persons.
improper extension cord could result in a
risk of fire and electric shock. If extension
cord must be used, make sure:
a. That pins on plug of extension cord
are the same number, size, and shape
as those of plug on charger;
6. To reduce risk of damage to electric plug
and cord, pull by plug rather than cord
when disconnecting charger.
b. That extension cord is properly wired
and in good electrical condition;
7. Make sure cord is located so that it will
not be stepped on, tripped over, or other-
wise subjected to damage or stress.
c. That wire size is at least as large as
the one specified in the table below.
8. An extension cord should not be used
unless absolutely necessary. Use of
Table 1: RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS
Length of Cord (Feet)
AWG Size of Cord
25
18
50
18
100
18
150
16
9. Do not operate charger with damaged
cord or plug - replace them immediately.
13. The battery charger is not intended for
use by young children or infirm persons
without supervision.
10. Do not operate charger if it has received a
sharp blow, been dropped, or otherwise
damaged in any way; take it to a qualified
serviceman.
14. Young children should be supervised to
ensure that they do not play with the bat-
tery charger.
11. Do not disassemble charger or battery
cartridge; take it to a qualified serviceman
when service or repair is required, Incor-
rect reassembly may result in a risk of
electric shock or fire.
15. If operating time has become excessively
shorter, stop operating immediately. It
may result in a risk of overheating, possi-
ble burns and even an explosion.
16. If electrolyte gets into your eyes, rinse
them out with clear water and seek medi-
cal attention right away. It may result in
loss of your eyesight.
12. To reduce risk of electric shock, unplug
charger from outlet before attempting any
maintenance or cleaning. Turning off con-
trols will not reduce this risk.
ADDITIONAL SAFETY RULES FOR CHARGER &
BATTERY CARTRIDGE
1. Do not charge Battery Cartridge when
temperature is BELOW 10°C (50°F) or
ABOVE 40°C (104°F).
2. Do not attempt to use a step-up trans-
former, an engine generator or DC power
receptacle.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Do not allow anything to cover or clog the
charger vents.
A battery short can cause a large current
flow, overheating, possible burns and
even a breakdown.
4. Always cover the battery terminals with
the battery cover when the battery car-
tridge is not used.
6. Do not store the tool and Battery Car-
tridge in locations where the temperature
may reach or exceed 50°C (122°F).
5. Do not short the battery cartridge:
7. Do not incinerate the Battery Cartridge
even if it is severely damaged or is com-
pletely worn out. The battery cartridge can
explode in a fire.
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects
such as nails, coins, etc.
8. Be careful not to drop, shake or strike bat-
tery.
(3) Do not expose battery cartridge to
water or rain.
9. Do not charge inside a box or container of
any kind. The battery must be placed in a
well ventilated area during charging.
SAVE THESE INSTRUCTIONS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONAL
DESCRIPTION
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before adjusting or
checking function on the tool.
001892
Installing or removing battery cartridge
•
•
•
Always switch off the tool before insertion or removal of
the battery cartridge.
2
To remove the battery cartridge, withdraw it from the tool
while pressing the buttons on both sides of the cartridge.
1
To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click. If not, it may accidentally fall out
of the tool, causing injury to you or someone around you.
1. Battery cartridge
2. Button
•
Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
001893
Charging
1
1. Plug the battery charger into the proper AC voltage
source. The charging light will flash in green color.
2
3
2. Insert the battery cartridge so that the plus and minus
terminals on the battery cartridge are on the same sides
as their respective markings on the high capacity battery
charger. Insert the cartridge fully into the port so that it
rests on the charger port floor.
1. Battery cartridge
2. Charging light
3. Battery charger
3. When the battery cartridge is inserted, the charging light
color will change from green to red and charging will
begin. The charging light will remain lit steadily during
charging.
4. When the charging light color changes from red to
green, the charging cycle is complete.
5. If you leave the battery cartridge in the charger after the
charging cycle is complete, the charger will switch into
its “trickle charge (maintenance charge)” mode which
will last approximately 24 hours.
6. After charging, unplug the charger from the power
source.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
•
The battery charger is for charging Makita battery
cartridge. Never use it for other purposes or for other
manufacturer’s batteries.
•
When you charge a new battery cartridge or a battery
cartridge which has not been used for a long period of
time, it may not accept a full charge. This is a normal
condition and does not indicate a problem. You can
recharge the battery cartridge fully after discharging it
completely and recharging a couple of times.
•
•
If you charge a battery cartridge from a just operated
tool or a battery cartridge which has been left in a
location exposed to direct sunlight or heat for a long
time, the charging light may flash in red color. If this
occurs, wait for a while. Charging will begin after the
battery cartridge cools. The battery cartridge will cool
faster if you remove the battery cartridge from the high
capacity battery charger.
If the charging light flashes alternately in green and red
color, a problem exists and charging is not possible. The
terminals on the charger or battery cartridge are clogged
with dust or the battery cartridge is worn out or
damaged.
Trickle charge (Maintenance charge)
If you leave the battery cartridge in the charger to prevent
spontaneous discharging after full charge, the charger will
switch into its “trickle charge (maintenance charge)” mode
and keep the battery cartridge fresh and fully charged.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely dis-
charged.
Always stop tool operation and charge the battery car-
tridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room temperature at
10°C - 40°C (50°F - 104°F).
Let a hot battery cartridge cool down before charging it.
4. Charge the Nickel Metal Hydride battery cartridge when
you do not use it for more than six months.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
001894
Switch action
CAUTION:
•
Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the “OFF” position when
released.
1
To star t the tool, simply pull the switch trigger. Tool speed is
increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
1. Switch trigger
Electric brake
This tool is equipped with an electric brake. If the tool consis-
tently fails to quickly stop after switch trigger release, have
tool serviced at a Makita service center.
001895
Reversing switch action
1
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A side
for clockwise rotation or from the B side for counterclockwise
rotation.
When the reversing switch lever is in the neutral position, the
switch trigger cannot be pulled.
3
2
1. Reversing switch lever
2. Clockwise
CAUTION:
3. Counterclockwise
•
•
Always check the direction of rotation before operation.
Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation before
the tool stops may damage the tool.
•
When not operating the tool, always set the reversing
switch lever to the neutral position.
001896
Speed change
To change the speed, first switch off the tool and then slide
the speed change lever to the “2” side for high speed or “1”
side for low speed. Be sure that the speed change lever is
set to the correct position before operation. Use the right
speed for your job.
1
CAUTION:
1. Speed change lever
•
Always set the speed change lever fully to the correct
position. If you operate the tool with the speed change
lever positioned halfway between the “1” side and “2”
side, the tool may be damaged.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Do not use the speed change lever while the tool is
running. The tool may be damaged.
001897
Selecting action mode
This tool has an action mode change lever. For drilling,
depress the lock button and then slide the action mode
1
2
change lever to the left (
symbol). For screwing, slide the
action mode change lever to the right (
locked.
symbol) until it is
If it is hard to turn the lever, first turn the chuck slightly in
either direction and then turn the lever again.
1. Lock button
2. Action mode change lever
CAUTION:
•
•
Always slide the action mode change lever all the way to
your desired mode position. If you operate the tool with
the lever positioned halfway between the mode symbols,
the tool may be damaged.
Do not use the action mode change lever while the tool
is running. The tool may be damaged.
001898
Adjusting the fastening torque
The fastening torque can be adjusted in 16 steps by turning
the adjusting ring so that its graduations are aligned with the
pointer on the tool body.
1
2
First, slide the action mode change lever to the position of
symbol.
3
1. Adjusting ring
2. Graduations
The fastening torque is minimum when the number 1 is
aligned with the pointer, and maximum when the marking is
aligned with the pointer. The clutch will slip at various torque
levels when set at the number 1 to 16. Before actual opera-
tion, drive a trial screw into your material or a piece of dupli-
cate material to determine which torque level is required for a
particular application.
3. Pointer
CAUTION:
•
The adjusting ring does not lock when the pointer is
positioned only halfway between the graduations.
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out any
work on the tool.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
001899
Installing or removing driver bit or drill bit
1
Hold the ring and turn the sleeve counterclockwise to open
the chuck jaws. Place the bit in the chuck as far as it will go.
Hold the ring firmly and turn the sleeve clockwise to tighten
the chuck.
2
To remove the bit, hold the ring and turn the sleeve counter-
clockwise.
1. Sleeve
2. Ring
001900
When not using the driver bit, keep it in the bit holders. Bits
45 mm long can be kept there.
2
1
1. Bit
2. Bit holder
OPERATION
001901
Screwdriving operation
First, slide the action mode change lever to the position of
symbol and select the fastening torque.
Place the point of the driver bit in the screw head and apply
pressure to the tool. Start the tool slowly and then increase
the speed gradually. Release the switch trigger as soon as
the clutch cuts in.
CAUTION:
•
•
Make sure that the driver bit is inserted straight in the
screw head, or the screw and/or bit may be damaged.
When driving wood screws, predrill pilot holes to make
driving easier and to prevent splitting of the workpiece.
See the chart.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Nominal diameter of
wood screw (mm)
3.1 (1/8”)
Recommended size
of pilot hole (mm)
2.0 - 2.2 (5/64” - 3/32”)
2.2 - 2.5 (3/32” - 3/32”)
2.5 - 2.8 (3/32” - 7/64”)
2.9 - 3.2 (7/64” - 1/8”)
3.1 - 3.4 (1/8” - 9/64”)
3.3 - 3.6 (1/8” - 9/64”)
3.7 - 3.9 (9/64” - 5/32”)
4.0 - 4.2 (5/32” - 11/64”)
4.2 - 4.4 (11/64” - 11/64”)
3.5 (9/64”)
3.8 (5/32”)
4.5 (11/64”)
4.8 (3/16”)
5.1 (13/64”)
5.5 (7/32”)
5.8 (7/32”)
6.1 (15/64”)
•
If the tool is operated continuously until the battery
cartridge has discharged, allow the tool to rest for 15
minutes before proceeding with a fresh battery.
Drilling operation
First, slide the action mode change lever to the position of
symbol.
Drilling in wood
•
When drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide
screw makes drilling easier by pulling the bit into the
workpiece.
Drilling in metal
•
To prevent the bit from slipping when starting a hole,
make an indentation with a center-punch and hammer at
the point to be drilled. Place the point of the bit in the
indentation and start drilling. Use a cutting lubricant
when drilling metals. The exceptions are iron and brass
which should be drilled dry.
CAUTION:
•
Pressing excessively on the tool will not speed up the
drilling. In fact, this excessive pressure will only serve to
damage the tip of your bit, decrease the tool
performance and shorten the service life of the tool.
•
•
There is a tremendous force exerted on the tool/bit at the
time of hole break through. Hold the tool firmly and exert
care when the bit begins to break through the workpiece.
A stuck bit can be removed simply by setting the
reversing switch to reverse rotation in order to back out.
However, the tool may back out abruptly if you do not
hold it firmly.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Always secure small workpieces in a vise or similar hold-
down device.
If the tool is operated continuously until the battery
cartridge has discharged, allow the tool to rest for 15
minutes before proceeding with a fresh battery.
001902
Installing set plate (optional accessory)
Model 6217D, 6317D only
1
Always install the set plate when using battery cartridges
1200, 1202, 1201A. Install the set plate on the tool with the
screw provided.
2
1. Screw
2. Set plate
MAINTENANCE
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
001145
Replacing carbon brushes
Remove and check the carbon brushes regularly. Replace
when they wear down to the limit mark. Keep the carbon
brushes clean and free to slip in the holders. Both carbon
brushes should be replaced at the same time. Use only iden-
tical carbon brushes.
1
1. Limit mark
001903
Use a screwdriver to remove the brush holder caps. Take out
the worn carbon brushes, insert the new ones and secure
the brush holder caps.
1
2
After replacing brushes, insert the battery cartridge into the
tool and break in brushes by running tool with no load for
about 1 minute. Then check the tool while running and elec-
tric brake operation when releasing the switch trigger. If elec-
tric brake is not working well, ask your local Makita service
center for repair.
1. Brush holder cap
2. Screwdriver
14
Download from Www.Somanuals.com. All Manuals Search And Download.
To maintain product SAFETY and RELIABILITY, repairs, any
other maintenance or adjustment should be performed by
Makita Authorized or Factory Service Centers, always using
Makita replacement parts.
EN0001-1
Recycling the Battery
The only way to dispose of a Makita battery is to recycle it.
The law prohibits any other method of disposal.
To recycle the battery:
1. Remove the battery from the cleaner.
Ni-Cd
2. a) Take the battery to your nearest Makita Factory Ser-
vice Center
or
b) Take the battery to your nearest Makita Authorized
Service Center or Distributor that had been desig-
nated as a Makita battery recycling location.
Call your nearest Makita Service Center or Distributor to
determine the location that provides Makita battery recycling.
See your local Yellow Pages under “Tools-Electric”.
ACCESSORIES
CAUTION:
•
These accessories or attachments are recommended for
use with your Makita tool specified in this manual. The
use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding these
accessories, ask your local Makita service center.
•
•
•
•
•
•
•
•
Drill bits
Screw bits
Battery charger DC1801/ DC1411
12V Battery cartridge 1222/1233/1234/1235
14.4V Battery cartridge 1422/1433/1434/1435
18V Battery cartridge 1822/1833/1834/1835
Set plate
Plastic case
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
16
Download from Www.Somanuals.com. All Manuals Search And Download.
First-Class
Postage
Required
Post Office will
not deliver
without proper
postage.
Makita U.S.A., Inc.
14930 Northam Street
La Mirada, CA 90638-5753
Fold
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIL THIS PORTION
Your answer to the following questions are appreciated.
1. This product was purchased from:
3. How did you learn about this product:
Home Center
Other (
)
Magazine
Radio
Hardware/Lumber Store
Tool Distributor
From Dealer
Newspaper
Store Display
Catalog
Exhibition
From Friend
Previous Usage
Other (
Industrial Supply
Construction Supply
)
2. Use of the product is intended for:
4. Most favored points are:
Construction Trade
Industrial Maintenance
Home Maintenance
Hobby
Design
Repair Service
Durability
Power
Features
Size
Price
Other (
)
Other (
)
Makita Brand
5. Any comments:
DATE PURCHASED
MONTH
MODEL NO.
DAY
YEAR
SERIAL NO.
STATUS
SEX
Married Single
M
F
INTL.
LAST NAME / COMPANY NAME
STREET ADRESS
CITY
AREA
CODE
STATE
ZIP CODE
PHONE
40-49
Under 19
20-29
30-39
50-60
Over 60
AGE:
BE SURE TO COMPLETE THE CUSTOMER’S PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.
Please return this portion by facsimile or mail.
Facsimile No: (714) 522-8133
Paste
Paste Paste Paste
Paste
Paste
Paste
Paste
Download from Www.Somanuals.com. All Manuals Search And Download.
FACTORY SERVICE CENTERS
1-800-4-MAKITA
RETAIN THIS PORTION FOR YOUR RECORDS
ALABAMA
COLORADO
KENTUCKY
NEW MEXICO
PUERTO RICO
2365 Pelham Parkway
Pelham, AL 35124
(205) 620-1791
11839 E. 51st Ave.
Denver, CO 80239-2709
(303) 371-2850
1215 S. Hurstbourne Parkway
Louisville, KY 40222
(502) 326-3740
5805 Menaul Blvd. NE
Albuquerque, NM 87110
(505) 881-4619
200 Guayama St.
Hato Rey, PR 00917
(787) 250-8776
ARIZONA
CONNECTICUT
508 Spring St.
Windsor Locks, CT 06096
(860) 292-6405
LOUSIANA
NEW YORK
TENNESSEE
3707 E. Broadway Rd., Ste. 6
Phoenix, AZ 85040
(602) 437-2850
5626 Jefferson Hwy.
Harahan, LA 70123
(504) 733-4138
4917 Genessee Street
Cheektowaga, NY 14225
(716) 685-9503
4655 Nolensville Rd.
Nashville, TN 37211
(615) 331-9922
131-35 31st Ave.
Flushing, NY 11354
(718) 886-0971
ARKANSAS
FLORIDA
MARYLAND
TEXAS
Shackleford Shopping Center
240 South Shackleford Rd.,
Ste. C
620 Douglas Ave. Suite 1302
Altamonte Springs, FL 32714
(407) 774-6000
7541 - 45 Ritchie Highway
Glen Burnie, MD 21061
(410) 590-0160
12801 Stemmons Fwy Ste. 809
Farmers Branch, TX 75234
(972) 243-1150
Little Rock, AR 72211
(501) 224-5733
NORTH CAROLINA
3501-G S. Tryon St.
Charlotte, NC 28217
(704) 527-0611
750 East Sample Road
Pompano Beach, FL 33064
(954) 781-6333
12701 Directors Dr.
Stafford, TX 77477-3701
(281) 565-8665
MASSACHUSETTS
232 Providence Hwy.
Westwood, MA 02090
(617) 461-9754
CALIFORNIA
41850 Christy St.
Fremont, CA 94538-5107
(510) 657-9881
Thompson Center Waters
5501 W. Waters Ave., Ste. 406
Tampa, FL 33634
3453 IH-35 North, Ste. 101
San Antonio, TX 78219
(210) 228-0676
OHIO
6253 E. Main St.
Columbus, OH 43213
(614) 860-0222
(813) 886-8292
MICHIGAN
1421 N. Clovis Ave., Ste. 112
Fresno, CA 93727
(559) 252-5166
37454 Ann Arbor Trail
Livonia, MI 48150
(313) 432-1012
UTAH
GEORGIA
6379 Pearl Road
Parma Heights, OH 44130
(440) 843-7555
145 E. 1300 S., Ste. 101
Salt Lake City, UT 84115
(801) 359-3410
4680 River Green Parkway
Duluth, GA 30096-2566
(770) 476-8911
14930 Northam St.
La Mirada, CA 90638-5753
(714) 522-8088
MINNESOTA
6427 Penn Ave. South
Richfield, MN 55423
(612) 869-5199
1617 E. Kemper Rd.
Sharonville, OH 45246
(513) 771-0788
VIRGINIA
5760 Northampton Blvd,. Ste.
102
Virginia Beach, VA 23455
(757) 460-0280
1970 Fulton Avenue
Sacramento, CA 95825
(916) 482-5197
HAWAII
4510 Salt Lake Blvd., Suite A7
Honolulu, HI 96818
(808) 847-0038
MISSOURI
OKLAHOMA
1440 South “E” Street
San Bernardino, CA 92408
(909) 885-1289
9876 Watson Road
St. Louis, MO 63126-2221
(314) 909-9889
552 E. Memorial Road
Oklahoma City, OK 73114
(405) 752-2655
ILLINOIS
WASHINGTON
1450 Feehanville Dr.
Mt. Prospect, IL 60056-6011
(847) 297-3100
22220 84th Ave. So., Bldg. A
Kent, WA 98032
(253) 395-8055
7674 Clairemont Mesa Blvd.
San Diego, CA 92111
(858) 278-4471
NEBRASKA
OREGON
4129 S. 84th St.
Omaha, NE 68127
(402) 597-2925
828 19th Avenue., N.W.
Portland, OR 97209
(503) 222-1823
1714 E.McFadden Ave., Unit M
Santa Ana, CA 92705
(714) 667-5066
INDIANA
WISCONSIN
8403 Michigan Road, Unit 1
Indianapolis, IN 46268
(317) 334-9980
Lincoln Plaza Shopping Ctr.
2245 S. 108th St. West Allis, WI
53227
NEVADA
3375 S. Decatur Blvd.
Suites. 22 - 24
Las Vegas, NV 89102
(702) 368-4277
PENNSYLVANIA
Springwater Plaza
364 Wilmington W. Chester
Pike
Glen Mills, PA 19342
(610) 459-4122
1565 Winchester B.
Campbell, CA 95008-0501
(408) 379-0377
(414) 541-4776
KANSAS
8819 W. 95th St.
Overland Park, KS 66212
(913) 642-1111
16735 Saticoy St., Ste. 105
Van Nuys, CA 91406
(818) 782-2440
NEW JERSEY
6200 Babcock Blvd
Pittsburgh, PA 15237
(412) 366-6363
251 Herrod Blvd.
Dayton, NJ 08810-1539
(609) 655-1212
CUSTOMER’S RECORD
Date Purchased
When you need service: Send
complete tool (prepaid) to one
of the Makita Factory Service
Centers listed, or to an Authorized
Makita Service Center. Be sure
to attach a letter to the outside of
the carton detailing the problem
with your tool.
Dealer’s Name & Address
Model No.
Serial No.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles.
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of
defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of
Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective
workmanship or material, Makita will repair (or at our option, replace) without charge.
This Warranty does not apply where:
• repairs have been made or attempted by others:
• repairs are required because of normal wear and tear:
• the tool has been abused, misused or improperly maintained:
• alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING
AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF
"MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE-YEAR TERM OF
THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary form state to state.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied
warranty lasts, so the above limitation may not apply to you.
Makita Corporation of America
2650 Buford Hwy., Buford, GA 30518
T1944-1
Imprimé aux Etats-Unis
MCA* 05/02
PRINTED IN U.S.A.
2002-05-GS
Download from Www.Somanuals.com. All Manuals Search And Download.
|