Band Saw
LB1200F
INSTRUCTION MANUAL
IMPORTANT: Read Before Using.
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Disconnect tools.
12. NEVER wear gloves during operation.
13. Keep hands out of the line of the saw blade.
14. NEVER stand or permit anyone else to stand in line with
the path of the saw blade.
15. Before using the tool on an actual workpiece, let it run for
a while. Watch for vibration or wobbling that could
indicate poor installation or a poorly balanced blade.
16. Replace the table insert when worn.
When not in use, before servicing and when changing
accessories such as blades, bits and cutters.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and adjusting
wrenches are removed from the tool before turning it on.
17. Avoid unintentional starting.
Do not carry a plugged-in tool with a finger on the switch.
Ensure switch is off when plugging in.
18. Use outdoor extension leads.
17. Connect band saw to a dust-collecting device when
sawing wood.
When tool is used outdoors, use only extension cords intended
for outdoor use.
18. Do not operate the machine when the door or guard
protecting the saw band is open.
19. Stay alert.
19. Take care that the selection of the saw band and the speed
depends on the material to be cut.
20. Do not clean the saw band whilst it is in motion.
Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
20. Check damaged parts.
Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it will
operate properly and perform its intended function. Check for
alignment of moving parts, free running of moving parts,
breakage of parts, mounting and any other conditions that may
affect its operation. A guard or other part that is damaged
should be properly repaired or replaced by an authorized
service center unless otherwise indicated in this instruction
manual. Have defective switches replaced by an authorized
service facility. Do not use the tool if the switch does not turn it
on and off.
21. Warning.
The use of any accessory or attachment, other than those
recommended in this instruction manual or the catalog, may
present a risk of personal injury.
22. Have your tool repaired by a qualified person.
This electric tool is in accordance with the relevant safety
requirements. Repairs should only be carried out by qualified
persons using original spare parts, otherwise this may result in
considerable danger to the user.
ADDITIONAL SAFETY RULES FOR
TOOL
SAVE THESE INSTRUCTIONS.
1. Wear eye protection.
2. Don’t use the tool in presence of flammable liquids or
gases.
3. Always use face or dust mask.
4. Check the blade carefully for cracks or damage before
operation. Replace cracked or damaged blade
immediately.
5. Use only saw blades recommended by the manufacturer
and which conform to EN847-1.
6. Always use accessories recommended in this manual.
Use of improper accessories such as abrasive cut-off
wheels may cause an injury.
7. Select the correct saw blade for the material to be cut.
8. Do not use saw blades manufactured from high speed
steel.
9. To reduce the emitted noise, always be sure that the blade
is sharp and clean.
10. Do not cut metals such as nails and screws. Inspect for
and remove all nails, screws and other foreign matter from
the workpiece before operation.
11. Remove wrenches, cut-off pieces, etc. from the table
before the switch is turned on.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Wheel
Knob (For tensioning blade)
Upper cover
Knob (For securing upper housing door)
Knob (For adjusting blade guide)
Knob (For securing blade guide)
Upper blade guide
Blade
Light switch
Switch
Rip fence
Knob (For securing lower housing door)
Knob (For tensioning V-belt)
Lower cover
Driving belt
Carry Handle
Wheel
Stand
Dust box
Tire
(Quick release) lever
Knob (For adjusting cutter tool tracking)
Grip (For adjusting table tilt)
Lock lever (For securing table tilt)
Dust extraction port
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALATION
Securing the band saw stand
If during operation there is any tendency for the band saw to tip over, slide or move, the band saw stand be secured to the floor.
1
2
Frame
3
4
5
• After attaching the stand, attach the handle and tires.
Handle
Washer
Hex socket
head bolt
Tire
5
Download from Www.Somanuals.com. All Manuals Search And Download.
How to load dust box
The dust box is loaded from the underside of the table saw. When loading, insert
plate spring (for securing) at inside edge of the machine’s positioning hole, slot both
shoulders of dust box onto rails, and then slide toward the outside.
Once the leading edge of the securing plate spring fits into the machine’s securing
hole, the dust box is loaded.
Securing
hole
Position
hole
Rail
Rail
Shoulder
Dust box
Shoulder
Plate spring
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure table to trunnion using four hex bolts.
Trunnion
Table
Hex bolts
Hex bolts
Pin is inserted at time of shipping, so please pull it out.
Pin
Table
Installing the guide rail
• Fasten the guide rail with four each thumb screws and washers to the table.
Washer
Thumb screw
Guide rail
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONAL DESCRIPTION
Switch action
Switch cover
CAUTION:
Light switch
OFF switch
• Before operation, make sure that the tool is turned on and off.
The switch cover can be opened easily by sliding it upwards.
To start the tool, press the ON (I) button.
To stop it, press the OFF (O) button or the switch cover.
Lighting up the lamps
Push the upper position (I) of the switch for turning on the light and the lower position
(O) for off.
ON switch
To start the tool, raise the switch lever.
To stop it, lower the switch lever.
ON
Push stick
Push stick
The push stick serves as an extension of the hand and protects against accidental
contact with the saw blade.
The push stick must always be used if the distance between band saw blade and a
rip fence is less than 150 mm.
Guide the push stick at an angle of 20º ... 30º against the saw table’s surface.
When the push stick is not used it can be stored on the push stick holder provided at
the band saw frame.
Replace push stick if damaged.
Miter gauge
Miter gauge
The miter gauge is inserting into the table slot from the tables front edge.
For miter cuts the miter gauge turns to 60º in both directions.
For 45º and 90º miters positive stops are provided.
To set a miter angle: loosen lock handle by turning it counter-clockwise.
WARNING:
When cutting with the miter gauge the lock handle must be firmly tightened.
The auxiliary fence can be taken off and reversed after loosening knob.
Knob
Lock handle
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Rip Fence
The rip fence can be used on both sides of the blade. When the rip fence is moved
from one side of the saw blade to the other the fence needs to reversed.
Rip fence
Reversing the fence
Knob (A)
1. Loosen knob (B) of the hold-down clamp.
2. Remove hold-down clamp from the fence.
3. Loosen knob (A).
Fence
4. Lift fence off the fence holder.
5. Reverse fence and slide back on the fence holder.
6. Tighten knob (A).
7. Slide hold-down clamp on the fence.
Clamping the rip fence
Lock lever
1. Place rip fence on the guide rail.
2. Tighten the lock lever of the rip fence.
3. Loosen the knob (B) of the hold-down clamp.
4. Slide hold-down clamp against the rear table edge.
5. Tighten the knob (B).
Fence holder
Knob (B)
Hold-down clamp
Fence height can be lowered when cutting thin materials.
1. Loosen knob (B) of the hold-down clamp.
2. Remove hold-down clamp from the fence.
3. Loosen knob (A).
4. Lift fence off the fence holder.
5. Slide knob (A) away from fence to remove.
6. Rotate fence 90º.
7. Insert knob (A) into the other groove of the fence.
8. Return fence to fence holder.
9. Tighten knob (A).
10. Slide hold-down clamp on the fence.
When fence height has been lowered, the 0 (zero) point changes. If the rip fence is
on the left side of the blade, slide the guide rail to the left to adjust to 0 point.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Guide rail
Changing the band saw blade
CAUTION:
• Contacting the band saw blade even with the band saw blade at standstill may
cause a personal injury.
• Saw blade is dangerous.
Be sure to wear gloves when handling saw blade in situations such as removing
from packaging, mounting or replacing blade.
1. Loosen the two thumb screws for the right-guide rail, and slide the right-side rail
to the right.
Thumb screws
2. Open the upper cover and lower cover on the tool.
3. Hold the handle and pull the dust cover upwards to remove.
Dust cover
10
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Open the lower blade guard.
5. Set the upper blade guide to its lowest position.
Saw blade
Saw housing
Upper blade guide
6. Loosen quick release lever until the band saw blade has slackened.
7. To remove the band saw blade, guide it through.
- the slot in the saw blade.
Lower blade guard
- the blade guard on the upper blade guides.
- the blade cover on the saw housing.
8. Fit a fresh band saw blade. Observe correct position: the teeth point towards the
front (door) side of the saw.
9. Center band saw blade on the rubber tyres of the band saw wheels.
10. Tighten quick release lever until blade does no longer slip off the band saw
wheels.
11. Close lower blade guard.
CAUTION:
Close lower cover only when the lower blade guard is in its closed position.
12. Return the right-guide rail to its original position.
13. Fit the dust cover.
Quick release lever
14. Close both covers.
15. Then:
- tension band saw blade (Refer to the section titled “Tensioning the band saw
blade” in “FUNCTIONAL DESCRIPTION”).
- align band saw blade (Refer to the section titled “Aligning the band saw blade”
“ASSEMBLY”).
- align blade guides (Refer to the section titled “Adjusting the upper blade guide”
in “FUNCTIONAL DESCRIPTION”).
- let saw test run for at least one minute;
- stop saw unplug and recheck settings.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Cutting speed adjustment
1. Open the lower cover.
Lower band saw wheel
2. Slacken driving belt by turning the knob clockwise.
3. Put driving belt on the required pulley of the driving wheel (lower band saw
wheel) and the corresponding motor pulley-note label inside the lower cover.
CAUTION:
The driving belt must run either on both front or both rear pulleys. Never have the V-
belt run diagonally.
8.3/6.7 m/s
16.7/13.3 m/s
(500/400 m/min)
(1,000/800 m/min)
Motor pulley
Setting knob for belt tension
With the setting knob the belt tension is corrected if necessary:
Knob
- turning the setting knob clockwise reduces the driving belt tension.
- turning the setting knob counter-clockwise increases the driving belt tension.
Lower cover
Tighten the driving belt again by turning the knob counter-clockwise (half-way
between the pulleys the driving belt should flex approx. 10 mm).
Close the lower cover.
Motor pulley
Pulley of the driving
wheel
Driving belt
approx. 10 mm
12
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONAL DESCRIPTION
Tensioning the Band saw Blade
Knob
CAUTION:
Too much tension can cause the band saw blade to break. Too little tension
can cause the driven band saw wheel to slip and the band saw blade to stop.
1. Raise upper blade guide fully.
Using the scale as guide, and taking the blade width into consideration, turn the
knob to adjust tension. (After adjusting, check tension as shown in item 2.)
2. Checking the blade tension:
- check tension by pushing with a finger, halfway between table and upper blade
guide, against the side of the blade (the blade should flex not more than 1-
2 mm)
- check adjustment at the blade tension indicator. The scale indicates the correct
adjustment in dependence on the band saw blade width.
3. Correct tension if necessary:
Upper blade guide
- turning the setting knob clockwise increases the blade tension.
- turning the setting knob counter-clockwise reduces the blade tension.
Aligning the band saw blade
If the band saw blade does not run in the center of the rubber tyres, the tracking
needs to be corrected by adjusting the tilt of the upper band saw wheel:
Lock knob
1. Loosen lock knob.
2. Manually rotate the upper wheel, taking care not to touch the blade.
3. Turn setting knob clockwise if the band saw blade runs towards the front of the
saw.
- turn setting knob counter-clockwise if the band saw blade runs toward the rear of
the saw
4. After adjusting, always close the lock knob.
Knob
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick release lever
With the quick release lever the saw blade tension is released.
Quick release lever
Clockwise: Reduce tension
Counterclockwise: Increase tension
Upper blade guide adjustment
The height of the upper blade guide needs to be adjusted:
prior to every cutting/operation, to accommodate the height of the work piece (the
upper blade guide should be set approx. 3 mm above the work piece);
- after adjustments of band saw blade or saw table (e.g. band saw blade change,
tensioning of the band saw blade, saw table alignment).
Adjusting knob
Lock knob
CAUTION:
Before adjusting the upper blade guide and saw table tilt:
- switch machine OFF;
- wait until the band saw blade has come to a complete stop.
• Set upper blade guide with the adjusting knob to the desired height by loosening
the lock knob.
After adjustment be sure to tighten the lock nut.
• Never cut several work pieces at the same time — and also no bundles containing
several individual pieces. Risk of personal injury if individual pieces are caught by
the saw blade uncontrolled.
Upper blade guide
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Loosen bolt C, and adjust bearing holder, so that guide bearing is positioned 1 or
2 mm from bottom of blade.
2. Loosen bolt A, and adjust thrust bearing to a position of 0.5 mm from rear of
blade.
Guide bearing
Bolt A
3. Loosen bolt B, and adjust guide bearing to a position 0.5 mm away from blade.
0.5 mm
Guide bearing distance
from bottom of blade
1 - 2 mm
Bolt C
0.5 mm
Bolt B
Guide bearing
Bearing holder
Thrust bearing
Bolt A
Blade
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Align the lower blade guide
The lower blade guide consists of:
- a thrust bearing (supporting the band saw blade from the rear).
- two guide bearings (providing lateral support).
These parts need to be readjusted after every band saw blade change or tracking
adjustment:
Note:
Bolt A
Periodically check thrust bearings and guide bearings for wear, if necessary replace
both guide bearings at the same time.
Thrust
bearing
• Open lower cover door and the lower blade guard.
• Loosen hex bolt, move the entire lower blade guide, and adjust the guide bearing
to a position of 1 or 2 mm from bottom of individual blade.
Hex bolt
Adjusting the thrust bearing
1. Loosen bolt A.
2. Adjust thrust bearing position (distance thrust bearing - band saw blade =
0.5 mm — if the band saw blade is turned by hand, it must not touch the thrust
bearing).
3. Tighten bolt A.
Adjusting the guide bearings
Guide bearing
1. Loosen bolt B.
2. Set guide bearing against the band saw blade.
3. Turn the band saw wheel by hand in a clockwise direction several times to bring
the guide bearings in correct position. Loosen bolt A, and adjust thrust bearing to
a position of 0.5 mm from rear of blade. Both guide bearings should JUST
TOUCH the band saw blade.
4. Tighten bolt B again.
5. Close lower blade guard.
6. Close the lower cover door.
Bolt B
Aligning the saw table at right angles to the band saw blade
1. Raise upper blade guide fully (see “Operation”).
Screw
2. Check band saw blade tension (see “FUNCTIONAL DESCRIPTION”).
Turn the handle clockwise to tilt the table in an anticlockwise direction, and turn
the handle anticlockwise to tilt the table in a clockwise direction.
3. Loosen lock lever.
4. Using a try square, set the table at right angles to the blade by turning the handle
to adjust the table, and tighten the lock lever again.
5. Adjust limit stop screw until it touches the saw housing.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Lock lever
Operation
Danger:
To reduce the risk of personal injury as much as possible, the following safety
recommendations should be observed when operating the saw.
CAUTION:
• Do not touch the saw blade when cutting.
• During saw operation, wear safety glasses, but do not wear gloves.
• Cut only one work piece at a time.
• Always hold the work piece down on the table.
• Do not jam any work pieces.
• Do not try to slow the band saw blade down or stop it by pushing the work piece
against the saw blade from the side.
• When straight cutting against the fence use a push stick.
• If the type of work requires, use the following:
- pushing stick — if distance rip fence - band saw blade 150 mm;
- work support — for long stock, which would otherwise fall off the table on
completion of the cut;
- dust collector;
- when cutting round stock, firmly secure material as shown in diagram.
- a suitable guide for firm support when cutting thin stock layed on edge.
- gloves for handling the saw band and rough material.
• Before starting work, check to see that the following are in proper working order:
- band saw blade;
- upper and lower blade guard.
• Replace damaged parts immediately.
• Assume correct work position (the band saw blade’s teeth must point towards the
operator).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Sawing
WARNING:
Risk of kickback (work piece is caught by the band saw blade and thrown against the
operator.)
Do not jam any work piece.
• Select rip fence and table tilt for the type of cutting operation to be carried out.
• Set upper blade guide 3 mm above the work piece.
Note:
Always make a trial cut in a piece of scrap to verify settings, correct if necessary
before cutting the work piece.
• Place work piece on the saw blade.
• Plug in.
• Start saw.
• Cut work piece in a single pass.
• Switch off if no further cutting is to be done immediately afterwards.
• Use separately retailed sub table.
Saw table tilt
Table
CAUTION:
When bevel-cutting with the table inclined, place the guide on the lower part of the
table.
After loosening the lock lever the saw table tilts steplessly through 47º against the
blade.
Turn the handle clockwise to tilt the table in an anticlockwise direction, and turn the
handle anticlockwise to tilt the table in a clockwise direction.
Lock lever
Handle
Connecting to vacuum cleaner
Cleaner operations can be performed by connecting the tool to Makita vacuum
cleaner or dust collector.
If a dust extractor is fitted to the large opening collector, rearrange dust collector to
ensure it has a large opening.
Nut
Large opening
collector
Small opening
collector
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Small dust
collector
Large dust
collector
(Mounted on
main unit)
(For
changeover)
How to move machine
• Raise handle to enable movement of machine.
• During transportation the saw band guard should be fully down and close to the
table.
• Do not use guarding for handling or transportation.
CAUTION:
Carry Handle
• If handle is raised too high, the machine may topple over.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and unplugged before attempting to
perform inspection or maintenance.
NOTICE:
• Never use gasoline, benzine, thinner, alcohol or the like. Discoloration,
deformation or cracks may result.
Cleaning
Clean out sawdust and chips from time to time. Carefully clean the blade guard and
moving parts inside the band saw.
Lubrication
To keep the band saw in tip-top running condition, and to assure maximum service
life, oil or grease the moving parts and rotating parts from time to time.
To reduce the emitted noise, always be sure that the blade is sharp and clean.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or
adjustment should be performed by Makita Authorized Service Centers, always
using Makita replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended for use with your Makita tool
specified in this manual. The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory or attachment for its stated
purpose. If you need any assistance for more details regarding these accessories,
ask your local Makita Service Center.
• Band saw stand
• Hex wrench
• Rip fence
• Miter gauge
• Circular ruler
• Extension table
• Sanding belt attachment
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Makita Corporation
JM21080008
ALA
Download from Www.Somanuals.com. All Manuals Search And Download.
|