Sander
MODEL GA7911
I N S T R U C T I O N M A N U A L
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
w w w. m a k i t a t o o l s . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Avoid body contact with grounded sur-
faces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.
14. Use safety equipment. Always wear eye
protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must
be used for appropriate conditions. Ordinary
eye or sun glasses are NOT eye protection.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
Tool Use and Care
15. Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand or
against your body is unstable and may lead
to loss of control.
7. Do not abuse the cord. Never use the cord
to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil,
sharp edges or moving parts. Replace
damaged cords immediately. Damaged
cords increase the risk of electric shock.
16. Do not force tool. Use the correct tool for
your application. The correct tool will do the
job better and safer at the rate for which it is
designed.
8. When operating a power tool outside, use
an outdoor extension cord marked “W-A”
or “W”. These cords are rated for outdoor
use and reduce the risk of electric shock.
17. Do not use tool if switch does not turn it
on or off. Any tool that cannot be controlled
with the switch is dangerous and must be
repaired.
Personal Safety
9. Stay alert, watch what you are doing and
use common sense when operating
a
18. Disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing the tool.
Such preventive safety measures reduce the
risk of starting the tool accidentally.
power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
19. Store idle tools out of reach of children
and other untrained persons. Tools are
dangerous in the hands of untrained users.
10. Dress properly. Do not wear loose cloth-
ing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
20. Maintain tools with care. Keep cutting
tools sharp and clean. Properly maintained
tools with sharp cutting edges are less likely
to bind and are easier to control.
11. Avoid accidental starting. Be sure switch
is off before plugging in. Carrying tools with
your finger on the switch or plugging in tools
that have the switch on invites accidents.
21. Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tools
operation. If damaged, have the tool ser-
viced before using. Many accidents are
caused by poorly maintained tools.
12. Remove adjusting keys or wrenches
before turning the tool on. A wrench or a
key that is left attached to a rotating part of
the tool may result in personal injury.
22. Use only accessories that are recom-
mended by the manufacturer for your
model. Accessories that may be suitable for
one tool, may become hazardous when used
on another tool.
13. Do not overreach. Keep proper footing
and balance at all times. Proper footing and
balance enables better control of the tool in
unexpected situations.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
24. When servicing a tool, use only identical
replacement parts. Follow instructions in
the Maintenance section of this manual.
Use of unauthorized parts or failure to follow
Maintenance instructions may create a risk of
electric shock or injury.
SERVICE
23. Tool service must be performed only by
qualified repair personnel. Service or main-
tenance performed by unqualified personnel
could result in a risk of injury.
USE PROPER EXTENSION CORD: Use only three-wire extension cords that have three-
prong grounding-type plugs and three-pole receptacles that accept the tool's plug. Make
sure your extension cord is in good condition. Replace or repair damaged or worn cord
immediately. When using an extension cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. Table 1 shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the
gage number, the heavier the cord.
Table 1: Minimum gage for cord
Volts
120 V
Total length of cord in feet
Ampere Rating
25 ft.
50 ft.
100 ft.
150 ft.
More Than
Not More Than
AWG
0
6
10
12
6
18
18
16
14
16
16
16
12
16
14
14
14
12
12
10
12
16
Not Recommended
GROUNDING INSTRUCTIONS
This tool should be grounded while in use to protect the operator from electric shock. The
tool is equipped with a three-conductor cord and three-prong grounding type plug to fit the
proper grounding type receptacle. The green (or green and yellow) conductor in the cord is
the grounding wire. Never connect the green (or green and yellow) wire to a live terminal.
Your unit is for use on 120 volts and has a plug that looks like Fig. “A”.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
An adapter Fig. “B” and “C” is available for connecting Fig. “A” type plugs to two-prong
receptacles. The green-colored rigid ear, lug, etc., extending from the adapter must be con-
nected to a permanent ground, such as a properly grounded outlet box.
GROUNDING METHODS
ADAPTER
GROUNDED
OUTLET
METAL
SCREW
GROUNDED
OUTLET BOX
TAB FOR
GROUNDING SCREW
GROUNDING
PIN
Fig. A
Fig. B
Fig. C
SPECIFIC SAFETY RULES
USB038-5
DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to sander safety rules. If
you use this tool unsafely or incorrectly, you can suffer serious
personal injury.
1. Accessories must be rated for at least the
speed recommended on the tool warning
label. Wheels and other accessories running
over rated speed can fly apart and cause
injury.
5. NEVER use tool with wood cutting blades
or other sawblades. Such blades when
used on a sander frequently kick and
cause loss of control leading to personal
injury.
2. Hold tool by insulated gripping surfaces
when performing an operation where the
cutting tool may contact hidden wiring or
its own cord. Contact with a “live” wire will
make exposed metal parts of the tool “live”
and shock the operator.
6. Hold the tool firmly.
7. Keep hands away from rotating parts.
8. Be careful not to damage the spindle, the
flange (especially the installing surface)
or the lock nut. Damage to these parts
could result in wheel breakage.
3. Always use safety glasses or goggles.
Ordinary eye or sun glasses are NOT
safety glasses.
9. Make sure the abrasive disc or the wheel
is not contacting the workpiece before the
switch is turned on.
4. Use only flanges specified for this tool.
10. Watch out for flying sparks. Hold the tool
so that sparks fly away from you and other
persons or flammable materials.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Do not leave the tool running. Operate the
tool only when hand-held.
IF USED AS A GRINDER
16. Always use proper guard with grinding
wheel. A guard protects operator from bro-
ken wheel fragments.
12. Do not touch the workpiece immediately
after operation; it may be extremely hot
and could burn your skin.
17. When using depressed center grinding
wheels, be sure to use only fiberglass-
reinforced wheels.
13. Ventilate your work area adequately when
you perform sanding operations.
14. ALWAYS wear proper apparel including
long sleeve shirts, leather gloves and
shop aprons to protect skin from contact
with hot grindings.
18. Check the wheel carefully for cracks or
damage
before
operation.
Replace
cracked or damaged wheel immediately.
Run the tool (with guard) at no load for
about a minute, holding tool away from
others. If wheel is flawed, it will likely sep-
arate during this test.
15. Use of this tool to grind or sand some
products, paints and wood could expose
user to dust containing hazardous sub-
stances. Use appropriate respiratory pro-
tection.
19. Before using the tool on an actual work-
piece, let it run for a while. Watch for
vibration or wobbling that could indicate
poor installation or
wheel.
a
poorly balanced
20. Use the specified surface of the wheel to
perform the grinding.
SAVE THESE INSTRUCTIONS
WARNING:
MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONAL
DESCRIPTION
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
001028
Shaft lock
CAUTION:
•
Never actuate the shaft lock when the spindle is moving.
The tool may be damaged.
1
Press the shaft lock to prevent spindle rotation when install-
ing or removing accessories.
1. Shaft lock
001043
Switch action
CAUTION:
•
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the “OFF”
position when released.
•
Switch can be locked in “ON” position for ease of
operator comfort during extended use. Apply caution
when locking tool in “ON” position and maintain firm
grasp on tool.
2
1
1. Switch trigger
2. Lock button
To start the tool, simply pull the switch trigger. Release the
switch trigger to stop. For continuous operation, pull the
switch trigger and then push in the lock button. To stop the
tool from the locked position, pull the switch trigger fully, then
release it.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
001059
Installing side grip (handle)
CAUTION:
•
Always be sure that the side grip is installed securely
before operation.
Screw the side grip securely on the position of the tool as
shown in the figure.
001114
Installing or removing abrasive disc
(optional accessory)
1
2
NOTE:
3
•
Use sander accessories specified in this manual. These
must be purchased separately.
Mount the rubber pad onto the spindle. Fit the disc on the
rubber pad and screw the lock nut onto the spindle.
1. Lock nut
2. Abrasive disc
3. Rubber pad
001621
To tighten the lock nut, press the shaft lock firmly so that the
spindle cannot revolve, then use the lock nut wrench and
securely tighten clockwise.
1
To remove the disc, follow the installation procedure in
reverse.
2
1. Lock nut wrench
2. Shaft lock
IF USED AS A GRINDER
NOTE:
•
Use grinder accessories specified in this manual. These
must be purchased by separate.
WARNING:
•
Always use guard assembly or accessory kit, noted
below, for type 27 depressed center grinding wheel/
Multi-disc.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Guard assembly
Part No. 191214-3 ... For 180 mm (7”)
Part No. 191215-1 ... For 230 mm (9”)
Guard accessory kit
Part No. 191228-2 ... For 180 mm (7”)
Part No. 191231-3 ... For 230 mm (9”)
001066
Installing or removing wheel guard
CAUTION:
1
•
When using a depressed center grinding wheel/Multi-
disc, flex wheel or wire wheel brush, the wheel guard
must be fitted on the tool so that the closed side of the
guard always points toward the operator.
2
3
Mount the wheel guard with the protrusion on the wheel
guard band aligned with the groove on the bearing box. Be
sure to tighten both screws securely.
1. Wheel guard
2. Bearing box
3. Screw
To remove wheel guard, follow the installation procedure in
reverse.
001078
Installing or removing depressed center grinding
wheel/Multi-disc (optional accessory)
1
2
WARNING:
3
•
Always use optional guard when depressed center
grinding wheel/Multi-disc is on tool. Wheel can shatter
during use and guard helps to reduce chances of
personal injury.
1. Lock nut
Mount the inner flange onto the spindle. Fit the wheel on the
inner flange and screw the lock nut onto the spindle.
2. Depressed center grinding wheel/
Multi-disc
3. Inner flange
001091
To tighten the lock nut, press the shaft lock firmly so that the
spindle cannot revolve, then use the lock nut wrench and
securely tighten clockwise.
1
To remove the wheel, follow the installation procedure in
reverse.
2
1. Lock nut wrench
2. Shaft lock
9
Download from Www.Somanuals.com. All Manuals Search And Download.
001103
Installing or removing flex wheel
(optional accessory)
1
2
3
4
WARNING:
•
Always use specific guard when depressed center
grinding wheel/Multi-disc is on tool. Wheel can shatter
during use and guard helps to reduce chances of
personal injury.
1. Lock nut
2. Flex wheel
3. Plastic pad
4. Inner flange
Follow instructions for depressed center grinding wheel/
Multi-disc but also use plastic pad over wheel. See order of
assembly on accessories page in this manual.
OPERATION
WARNING:
•
It should never be necessary to force the tool. The
weight of the tool applies adequate pressure. Forcing
and excessive pressure could cause dangerous wheel
breakage.
•
•
•
ALWAYS replace wheel if tool is dropped while grinding.
NEVER bang or hit grinding disc or wheel onto work.
Avoid bouncing and snagging the wheel, especially
when working corners, sharp edges etc. This can cause
loss of control and kickback.
•
NEVER use tool with wood cutting blades and other
sawblades. Such blades when used on a grinder
frequently kick and cause loss of control leading to
personal injury.
CAUTION:
•
After operation, always switch off the tool and wait until
the wheel has come to a complete stop before putting
the tool down.
001129
Grinding and sanding operation
ALWAYS hold the tool firmly with one hand on rear handle
and the other on the side handle. Turn the tool on and then
apply the wheel or disc to the workpiece.
In general, keep the edge of the wheel or disc at an angle of
about 15 degrees to the workpiece surface.
15˚
During the break-in period with a new wheel, do not work the
grinder in the B direction or it will cut into the workpiece.
Once the edge of the wheel has been rounded off by use, the
wheel may be worked in both A and B direction.
A
B
10
Download from Www.Somanuals.com. All Manuals Search And Download.
001143
Operation with wire cup brush
(optional accessory)
1
2
CAUTION:
•
•
Check operation of brush by running tool with no load,
insuring that no one is in front of or in line with brush.
Do not use brush that is damaged, or which is out of
balance. Use of damaged brush could increase potential
for injury from contact with broken brush wires.
1. Wire cup brush
2. Urethane washer
Unplug tool and place it upside down allowing easy access
to spindle. Remove any accessories on spindle. Mount ure-
thane washer then thread wire cup brush onto spindle and
tighten with supplied wrench. When using brush, avoid
applying too much pressure which causes over bending of
wires, leading to premature breakage.
NOTE:
•
When using wire cup brush, mount urethane washer to
the spindle. It will make it easier to remove wire cup
brush.
001236
Operation with wire wheel brush
(optional accessory)
1
CAUTION:
•
•
Check operation of wire wheel brush by running tool with
no load, insuring that no one is in front of or in line with
the wire wheel brush.
Do not use wire wheel brush that is damaged, or which
is out of balance. Use of damaged wire wheel brush
could increase potential for injury from contact with
broken wires.
1. Wire wheel brush
•
ALWAYS use guard with wire wheel brushes, assuring
diameter of wheel fits inside guard. Wheel can shatter
during use and guard helps to reduce chances of
personal injury.
Unplug tool and place it upside down allowing easy access
to spindle. Remove any accessories on spindle. Thread wire
wheel brush onto spindle and tighten with the wrenches.
When using wire wheel brush, avoid applying too much pres-
sure which causes over bending of wires, leading to prema-
ture breakage.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CAUTION:
001171
•
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
1
The tool and its air vents have to be kept clean. Regularly
clean the tool’s air vents or whenever the vents start to
become obstructed.
2
1. Exhaust vent
2. Inhalation vent
001145
Replacing carbon brushes
Remove and check the carbon brushes regularly. Replace
when they wear down to the limit mark. Keep the carbon
brushes clean and free to slip in the holders. Both carbon
brushes should be replaced at the same time. Use only iden-
tical carbon brushes.
1
1. Limit mark
001156
Use a screwdriver to remove the brush holder caps. Take out
the worn carbon brushes, insert the new ones and secure
the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs, any
other maintenance or adjustment should be performed by
Makita Authorized or Factory Service Centers, always using
Makita replacement parts.
1
2
1. Brush holder cap
2. Screwdriver
ACCESSORIES
CAUTION:
•
•
These accessories or attachments are recommended for
use with your Makita tool specified in this manual. The
use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you decide to use your Makita sander with approved
accessories which you purchase from your Makita
distributor or factory service center, be sure to obtain
and use all necessary fasteners and guards as
12
Download from Www.Somanuals.com. All Manuals Search And Download.
recommended in this manual. Your failure to do so could
result in personal injury to you and others.
If you need any assistance for more details regarding these
accessories, ask your local Makita service center.
001186
1
2
2
8
2
12
13
3
4
5
3
6
9
11
10
7
5
GA7911
1
2
Grip 36
Wheel guard
Inner flange 89
3
4
Depressed center grinding wheel/Multi-disc
Lock nut 5/8-45
5
6
Plastic pad
7
Flex wheel
8
Rubber pad 170
9
Abrasive disc
10
11
12
13
-
Sanding lock nut 5/8-48
Wire wheel brush
Urethane washer 14
Wire cup brush
Lock nut wrench 28
Accessory kit 7” or 9”
-
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
16
Download from Www.Somanuals.com. All Manuals Search And Download.
First-Class
Postage
Required
Post Office will
not deliver
without proper
postage.
Makita U.S.A., Inc.
14930 Northam Street
La Mirada, CA 90638-5753
Fold
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIL THIS PORTION
Your answer to the following questions are appreciated.
1. This product was purchased from:
3. How did you learn of about this product:
Home Center
Other (
)
Magazine
Radio
Hardware/Lumber Store
Tool Distributor
From Dealer
Newspaper
Store Display
Catalog
Exhibition
From Friend
Previous Usage
Other (
Industrial Supply
Construction Supply
)
2. Use of the product is intended for:
4. Most favored points are:
Construction Trade
Industrial Maintenance
Home Maintenance
Hobby
Design
Repair Service
Durability
Power
Features
Size
Price
Other (
)
Other (
)
Makita Brand
5. Any comments:
DATE PURCHASED
MONTH
MODEL NO.
DAY
YEAR
SERIAL NO.
STATUS
SEX
Married Single
M
F
INTL.
LAST NAME / COMPANY NAME
STREET ADRESS
CITY
AREA
CODE
STATE
ZIP CODE
PHONE
40-49
Under 19
20-29
30-39
50-60
Over 60
AGE:
BE SURE TO COMPLETE THE CUSTOMER’S PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.
Please return this portion by facsimile or mail.
Facsimile No: (714) 522-8133
Download from Www.Somanuals.com. All Manuals Search And Download.
Paste
Paste
Paste
Paste
Paste
Paste
Paste
Paste
FACTORY SERVICE CENTERS
1-800-4-MAKITA
RETAIN THIS PORTION FOR YOUR RECORDS
ALABAMA
COLORADO
KENTUCKY
NEW MEXICO
PUERTO RICO
2365 Pelham Parkway
Pelham, AL 35124
(205) 620-1791
11839 E. 51st Ave.
Denver, CO 80239-2709
(303) 371-2850
1215 S. Hurstbourne Parkway
Louisville, KY 40222
(502) 326-3740
5805 Menaul Blvd. NE
Albuquerque, NM 87110
(505) 881-4619
200 Guayama St.
Hato Rey, PR 00917
(787) 250-8776
ARIZONA
CONNECTICUT
508 Spring St.
Windsor Locks, CT 06096
(860) 292-6405
LOUSIANA
NEW YORK
TENNESSEE
3707 E. Broadway Rd., Ste. 6
Phoenix, AZ 85040
(602) 437-2850
5626 Jefferson Hwy.
Harahan, LA 70123
(504) 733-4138
4917 Genessee Street
Cheektowaga, NY 14225
(716) 685-9503
4655 Nolensville Rd.
Nashville, TN 37211
(615) 331-9922
131-35 31st Ave.
Flushing, NY 11354
(718) 886-0971
ARKANSAS
FLORIDA
MARYLAND
TEXAS
Shackleford Shopping Center
240 South Shackleford Rd.,
Ste. C
620 Douglas Ave. Suite 1302
Altamonte Springs, FL 32714
(407) 774-6000
7541 - 45 Ritchie Highway
Glen Burnie, MD 21061
(410) 590-0160
12801 Stemmons Fwy Ste. 809
Farmers Branch, TX 75234
(972) 243-1150
Little Rock, AR 72211
(501) 224-5733
NORTH CAROLINA
3501-G S. Tryon St.
Charlotte, NC 28217
(704) 527-0611
750 East Sample Road
Pompano Beach, FL 33064
(954) 781-6333
12701 Directors Dr.
Stafford, TX 77477-3701
(281) 565-8665
MASSACHUSETTS
232 Providence Hwy.
Westwood, MA 02090
(617) 461-9754
CALIFORNIA
41850 Christy St.
Fremont, CA 94538-5107
(510) 657-9881
Thompson Center Waters
5501 W. Waters Ave., Ste. 406
Tampa, FL 33634
3453 IH-35 North, Ste. 101
San Antonio, TX 78219
(210) 228-0676
OHIO
6253 E. Main St.
Columbus, OH 43213
(614) 860-0222
(813) 886-8292
MICHIGAN
1421 N. Clovis Ave., Ste. 112
Fresno, CA 93727
(559) 252-5166
37454 Ann Arbor Trail
Livonia, MI 48150
(313) 432-1012
UTAH
GEORGIA
6379 Pearl Road
Parma Heights, OH 44130
(440) 843-7555
145 E. 1300 S., Ste. 101
Salt Lake City, UT 84115
(801) 359-3410
4680 River Green Parkway
Duluth, GA 30096-2566
(770) 476-8911
14930 Northam St.
La Mirada, CA 90638-5753
(714) 522-8088
MINNESOTA
6427 Penn Ave. South
Richfield, MN 55423
(612) 869-5199
1617 E. Kemper Rd.
Sharonville, OH 45246
(513) 771-0788
VIRGINIA
5760 Northampton Blvd,. Ste.
102
Virginia Beach, VA 23455
(757) 460-0280
1970 Fulton Avenue
Sacramento, CA 95825
(916) 482-5197
HAWAII
4510 Salt Lake Blvd., Suite A7
Honolulu, HI 96818
(808) 847-0038
MISSOURI
OKLAHOMA
1440 South “E” Street
San Bernardino, CA 92408
(909) 885-1289
9876 Watson Road
St. Louis, MO 63126-2221
(314) 909-9889
552 E. Memorial Road
Oklahoma City, OK 73114
(405) 752-2655
ILLINOIS
WASHINGTON
1450 Feehanville Dr.
Mt. Prospect, IL 60056-6011
(847) 297-3100
22220 84th Ave. So., Bldg. A
Kent, WA 98032
(253) 395-8055
7674 Clairemont Mesa Blvd.
San Diego, CA 92111
(858) 278-4471
NEBRASKA
OREGON
4129 S. 84th St.
Omaha, NE 68127
(402) 597-2925
828 19th Avenue., N.W.
Portland, OR 97209
(503) 222-1823
1714 E.McFadden Ave., Unit M
Santa Ana, CA 92705
(714) 667-5066
INDIANA
WISCONSIN
8403 Michigan Road, Unit 1
Indianapolis, IN 46268
(317) 334-9980
Lincoln Plaza Shopping Ctr.
2245 S. 108th St. West Allis, WI
53227
NEVADA
3375 S. Decatur Blvd.
Suites. 22 - 24
Las Vegas, NV 89102
(702) 368-4277
PENNSYLVANIA
Springwater Plaza
364 Wilmington W. Chester
Pike
Glen Mills, PA 19342
(610) 459-4122
1565 Winchester B.
Campbell, CA 95008-0501
(408) 379-0377
(414) 541-4776
KANSAS
8819 W. 95th St.
Overland Park, KS 66212
(913) 642-1111
16735 Saticoy St., Ste. 105
Van Nuys, CA 91406
(818) 782-2440
NEW JERSEY
6200 Babcock Blvd
Pittsburgh, PA 15237
(412) 366-6363
251 Herrod Blvd.
Dayton, NJ 08810-1539
(609) 655-1212
CUSTOMER’S RECORD
Date Purchased
When you need service: Send
complete tool (prepaid) to one
of the Makita Factory Service
Centers listed, or to an Authorized
Makita Service Center. Be sure
to attach a letter to the outside of
the carton detailing the problem
with your tool.
Dealer’s Name & Address
Model No.
Serial No.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles.
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of
defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of
Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective
workmanship or material, Makita will repair (or at our option, replace) without charge.
This Warranty does not apply where:
• repairs have been made or attempted by others:
• repairs are required because of normal wear and tear:
• The tool has been abused, misused or improperly maintained:
• alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING
AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF
"MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE-YEAR TERM OF
THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary form state to state.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied
warranty lasts, so the above limitation may not apply to you.
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446-8502 Japan
883272H062
Download from Www.Somanuals.com. All Manuals Search And Download.
|