Angle Cutter
255 mm (10”)
MODEL 4110C
003505
DOUBLE
INSULATION
I N S T R U C T I O N M A N U A L
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
w w w. m a k i t a t o o l s . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Avoid body contact with grounded sur-
faces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.
14. Use safety equipment. Always wear eye
protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must
be used for appropriate conditions. Ordinary
eye or sun glasses are NOT eye protection.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
Tool Use and Care
15. Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand or
against your body is unstable and may lead
to loss of control.
7. Do not abuse the cord. Never use the cord
to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil,
sharp edges or moving parts. Replace
damaged cords immediately. Damaged
cords increase the risk of electric shock.
16. Do not force tool. Use the correct tool for
your application. The correct tool will do the
job better and safer at the rate for which it is
designed.
8. When operating a power tool outside, use
an outdoor extension cord marked “W-A”
or “W”. These cords are rated for outdoor
use and reduce the risk of electric shock.
17. Do not use tool if switch does not turn it
on or off. Any tool that cannot be controlled
with the switch is dangerous and must be
repaired.
Personal Safety
9. Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use tool while tired or
under the influence of drugs, alcohol, or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
18. Disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing the tool.
Such preventive safety measures reduce the
risk of starting the tool accidentally.
19. Store idle tools out of reach of children
and other untrained persons. Tools are
dangerous in the hands of untrained users.
10. Dress properly. Do not wear loose cloth-
ing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from
moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
20. Maintain tools with care. Keep cutting
tools sharp and clean. Properly maintained
tools with sharp cutting edges are less likely
to bind and are easier to control.
11. Avoid accidental starting. Be sure switch
is off before plugging in. Carrying tools with
your finger on the switch or plugging in tools
that have the switch on invites accidents.
21. Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tools
operation. If damaged, have the tool ser-
viced before using. Many accidents are
caused by poorly maintained tools.
12. Remove adjusting keys or wrenches
before turning the tool on. A wrench or a
key that is left attached to a rotating part of
the tool may result in personal injury.
22. Use only accessories that are recom-
mended by the manufacturer for your
model. Accessories that may be suitable for
one tool, may become hazardous when used
on another tool.
13. Do not overreach. Keep proper footing
and balance at all times. Proper footing and
balance enables better control of the tool in
unexpected situations.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
24. When servicing a tool, use only identical
replacement parts. Follow instructions in
the Maintenance section of this manual.
Use of unauthorized parts or failure to follow
Maintenance instructions may create a risk of
electric shock or injury.
SERVICE
23. Tool service must be performed only by
qualified repair personnel. Service or main-
tenance performed by unqualified personnel
could result in a risk of injury.
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. Table 1 shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num-
ber, the heavier the cord.
Table 1: Minimum gage for cord
Volts
120 V
Total length of cord in feet
Ampere Rating
25 ft.
50 ft.
100 ft.
150 ft.
More Than
Not More Than
AWG
0
6
10
12
6
18
18
16
14
16
16
16
12
16
14
14
14
12
12
10
12
16
Not Recommended
SPECIFIC SAFETY RULES
USB072-1
DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to cutter safety rules. If
you use this tool unsafely or incorrectly, you can suffer serious
personal injury.
1. DANGER! Keep hands away from cutting
area and wheel. Keep your second hand
on auxiliary handle or motor housing. If
both hands are holding the tool, they cannot
be cut by the wheel.
3. Do not reach underneath the work. Do not
attempt to remove cut material when wheel is
moving.
CAUTION: Wheels coast after turn off.
4. Always observe that the wheel has
stopped spinning before placing tool
down on bench or floor. A coasting wheel
will cause the tool to walk backwards, cutting
whatever is in its path. Be aware of the time it
takes for the wheel to stop after switch is
released.
2. Keep your body positioned to either side
of the wheel, but not in line with the wheel.
KICKBACK could cause the tool to jump
backwards. (See “Causes and Operator Pre-
vention of Kickback”)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5. NEVER hold piece being cut in your hands
or across your leg. It is important to support
the work properly to minimize body exposure,
wheel binding, or loss of control.
tion your body and arm to allow you to
resist KICKBACK forces. KICKBACK forces
can be controlled by the operator, if proper
precautions are taken.
When wheel is binding, or when interrupt-
ing a cut for any reason, release the trig-
ger and hold the tool motionless in the
material until the wheel comes to a com-
plete stop. Never attempt to remove the
tool from the work or pull the tool back-
ward while the wheel is in motion or KICK-
BACK may occur. Investigate and take
corrective actions to eliminate the cause of
wheel binding.
When restarting a tool in the workpiece,
center the wheel in the kerf and check that
teeth are not engaged into the material. If
wheel is binding, it may walk up or KICK-
BACK from the workpiece as the tool is
restarted.
6. Hold tool by insulated gripping surfaces
when performing an operation where the
cutting tool may contact hidden wiring or
its own cord. Contact with a “live” wire will
also make exposed metal parts of the tool
“live” and shock the operator.
7. When ripping always use a rip fence or
straight edge guide. This improves the
accuracy of cut and reduces the chance for
wheel binding.
8. Always use wheels with correct size and
shape (diamond vs. round) arbor holes.
Wheels that do not match the mounting hard-
ware of the tool will run eccentrically, causing
loss of control.
Support large panels to minimize the risk
of wheel pinching and KICKBACK. Large
panels tend to sag under their own weight.
Supports must be placed under the panel on
both sides, near the line of cut and near the
edge of the panel.
9. Never use damaged or incorrect wheel
washers or bolts. The wheel washers and
bolt were specially designed for your tool, for
optimum performance and safety of opera-
tion.
To minimize the risk of wheel pinching and
kickback. When cutting operation requires
the resting of the tool on the workpiece, the
tool shall be rested on the larger portion and
the smaller piece cut off.
Do not use dull or damaged wheel.
Unsharpened or improperly set wheels pro-
duce narrow kerf causing excessive friction,
wheel binding and KICKBACK.
Wheel depth and bevel adjusting locking
levers must be tight and secure before
making cut. If wheel adjustment shifts while
cutting, it may cause binding and KICKBACK.
Use extra caution when making a “Pocket
Cut” into existing walls or other blind
areas. The protruding wheel may cut objects
that can cause KICKBACK.
NEVER place your hand or fingers behind
the tool. If kickback occurs, the tool could
easily jump backwards over your hand, lead-
ing to serious personal injury.
10. Causes and Operator Prevention of Kick-
back:
Kickback is a sudden reaction to a pinched,
bound, or misaligned wheel, causing an
uncontrolled tool to lift up and out of the work-
piece toward the operator.
When the wheel is pinched or bound tightly
by the kerf closing down, the wheel stalls and
the motor reaction drives the unit rapidly back
toward the operator.
If the wheel becomes twisted or misaligned in
the cut, the teeth at the back edge of the
wheel can dig into the top surface of the
material being cut causing the wheel to climb
out of the kerf and jump back toward the
operator.
Kickback is the result of tool misuse and/or
incorrect operating procedures or conditions
and can be avoided by taking proper precau-
tions as given below:
Maintain a firm grip on the tool and posi-
5
Download from Www.Somanuals.com. All Manuals Search And Download.
11. When operating the tool, keep the cord
away from the cutting area and position it
so that it will not be caught on the work-
piece during the cutting operation. Oper-
ate with proper hand support, proper
workpiece support, and supply cord rout-
ing away from the work area.
or bolt. Damage to these parts could
result in wheel breakage.
16. Make sure the wheel is not contacting the
workpiece before the switch is turned on.
Wait until the wheel attains full speed
before cutting.
WARNING: It is important to support the
workpiece properly and to hold the tool
firmly to prevent loss of control which
could cause personal injury.
17. Stop operation immediately if you notice
anything abnormal.
18. Never attempt to cut with the tool held
upside down in a vise. This can lead to
serious accidents, because it is extremely
dangerous.
12. NEVER use tool with wood cutting blades
or other sawblades. Such blades when
used on this tool frequently kick and
cause loss of control leading to personal
injury.
19. Do not stop the wheel by lateral pressure
on the disc.
20. Some material contains chemicals which
may be toxic. Take caution to prevent dust
inhalation and skin contact. Follow mate-
rial supplier safety data.
13. Check the wheel carefully for cracks or
damage
before
operation.
Replace
cracked or damaged wheel immediately.
14. Use only flanges specified for this tool.
21. The tool must be used only for dry cutting.
15. Be careful not to damage the spindle,
DO NOT use water.
flanges (especially the installing surface)
SAVE THESE INSTRUCTIONS
WARNING:
MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONAL
DESCRIPTION
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
003511
Adjusting the depth of cut
1
2
Loosen the wing bolt on the depth guide and move the base
up or down. At the desired depth of cut, secure the base by
tightening the wing bolt.
3
4
1. Depth guide
2. Wing bolt
3. Cutting depth
4. Base
003518
securing safety guard
1
The safety guard can be adjusted about 80 degrees, after
you loosen the wing nut. Adjust to the desired angle, then
secure the wing nut.
2
1. Wing nut
2. Safety guard
003524
Switch action
CAUTION:
•
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the “OFF”
position when released.
1
To start the tool, simply pull the switch trigger. Release the
switch trigger to stop.
1. Switch trigger
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
003530
Installing or removing the wheel
1
To replace the wheel, depress the shaft lock to hold the shaft
stationary, then loosen the hex bolt clockwise with the socket
wrench.
Be sure to fully tighten the hex bolt counterclockwise after
mounting the new wheel, or operation will be dangerous.
2
NOTE:
1. Socket wrench
2. Shaft lock
•
Hex bolt has a left-hand thread.
OPERATION
003546
The cut is made by pulling the tool toward you (not by push-
ing away from you). Align the notch on the base with your
cutting line when performing a cut.
Hold the tool firmly. Set the base plate on the workpiece to
be cut without the wheel making any contact. Then turn the
tool on and wait until the wheel attains full speed. Move the
tool toward you over the workpiece surface, keeping it flat
and advancing smoothly until the cutting is completed. Keep
your cutting line straight and your speed of advance uniform.
1
2
1. Notch (Groove)
2. Cutting line
CAUTION:
•
Use this tool for straight line cutting only. Cutting curves
can cause stress cracks or fragmentation of the diamond
wheel and abrasive cut-off wheel resulting in possible
injury to persons in the vicinity.
MAINTENANCE
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
001145
Replacing carbon brushes
Remove and check the carbon brushes regularly. Replace
when they wear down to the limit mark. Keep the carbon
brushes clean and free to slip in the holders. Both carbon
brushes should be replaced at the same time. Use only iden-
tical carbon brushes.
1
1. Limit mark
8
Download from Www.Somanuals.com. All Manuals Search And Download.
003551
Use a screwdriver to remove the brush holder caps. Take out
the worn carbon brushes, insert the new ones and secure
the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs, any
other maintenance or adjustment should be performed by
Makita Authorized or Factory Service Centers, always using
Makita replacement parts.
1
2
1. Brush holder cap
2. Screwdriver
ACCESSORIES
CAUTION:
•
These accessories or attachments are recommended for
use with your Makita tool specified in this manual. The
use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding these
accessories, ask your local Makita service center.
•
•
•
•
255 mm (10”) Diamond wheels (Dry type)
305 mm (12”) Abrasive cut-off wheels
Socket wrench
Plastic carrying case
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
12
Download from Www.Somanuals.com. All Manuals Search And Download.
First-Class
Postage
Required
Post Office will
not deliver
without proper
postage.
Makita U.S.A., Inc.
14930 Northam Street
La Mirada, CA 90638-5753
Fold
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIL THIS PORTION
Your answers to the following questions are appreciated.
1.This product was purchased from:
3. How did you learn about this product:
Home Center
Other (
)
Magazine
Radio
Hardware/Lumber Store
Tool Distributor
From Dealer
Newspaper
Store Display
Catalog
Exhibition
From Friend
Previous Usage
Other (
Industrial Supply
Construction Supply
)
2. Use of the product is intended for:
4. Most favored points are:
Construction Trade
Industrial Maintenance
Home Maintenance
Hobby
Design
Repair Service
Durability
Power
Features
Size
Price
Other (
)
Other (
)
Makita Brand
5. Any comments:
DATE PURCHASED
MONTH
MODEL NO.
DAY
YEAR
SERIAL NO.
STATUS
SEX
Married Single
M
F
INTL.
LAST NAME / COMPANY NAME
STREET ADRESS
CITY
AREA
CODE
STATE
ZIP CODE
PHONE
40-49
Under 19
20-29
30-39
50-60
Over 60
AGE:
BE SURE TO COMPLETE THE CUSTOMER’S PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.
Please return this portion by facsimile or mail.
Facsimile No: (714) 522-8133
Download from Www.Somanuals.com. All Manuals Search And Download.
Paste
Paste
Paste
Paste
Paste
Paste
Paste
Paste
FACTORY SERVICE CENTERS
1-800-4-MAKITA
RETAIN THIS PORTION FOR YOUR RECORDS
ARIZONA
FLORIDA
MISSOURI
PENNSYLVANIA
1704 Babcock Blvd.
Pittsburgh, PA 15209
(412) 822-7370
3707 E. Broadway Rd., Ste. 6
Phoenix, AZ 85040
(602) 437-2850
750 East Sample Road
Pompano Beach, FL 33064
(954) 781-6333
9876 Watson Road
St. Louis, MO 63126-2221
(314) 909-9889
CALIFORNIA
GEORGIA
NEBRASKA
PUERTO RICO
41850 Christy St.
Fremont, CA 94538-5107
(510) 657-9881
4680 River Green Parkway NW
Duluth, GA 30096
(770) 476-8911
4129 S. 84th St.
Omaha, NE 68127
(402) 597-2925
200 Guayama St.
Hato Rey, PR 00917
(787) 250-8776
14930 Northam St.
La Mirada, CA 90638-5753
(714) 522-8088
ILLINOIS
NEVADA
3375 S. Decatur Blvd.
Suites. 22 - 24
Las Vegas, NV 89102
(702) 368-4277
TENNESSEE
1120 Elm Hill P.
Suile 170 Nashville, TN 372
(615) 248-3321
1450 Feehanville Dr.
Mt. Prospect, IL 60056-6011
(847) 297-3100
1970 Fulton Avenue
Sacramento, CA 95825
(916) 482-5197
MARYLAND
TEXAS
7674 Clairemont Mesa Blvd.
San Diego, CA 92111
(858) 278-4471
7397 Washington Boulevard,
Suite 104 Elkridge, MD 21075
(410) 796-4401
NEW JERSEY
12801 Stemmons Fwy Ste. 809
Farmers Branch, TX 75234
(972) 243-1150
251 Herrod Blvd.
Dayton, NJ 08810-1539
(609) 655-1212
16735 Saticoy St., Ste. 105
Van Nuys, CA 91406
(818) 782-2440
12701 Directors Dr.
Stafford, TX 77477-3701
(281) 565-8665
MASSACHUSETTS
232 Providence Hwy.
Westwood, MA 02090
(781) 461-9754
NEWYORK
4917 Genessee Street
Cheektowaga, NY 14225
(716) 685-9503
3453 IH-35 North, Ste. 101
San Antonio, TX 78219
(210) 228-0676
COLORADO
11839 E. 51st Ave.
Denver, CO 80239-2709
(303) 371-2850
MINNESOTA
6427 Penn Ave. South
Richfield, MN 55423
(612) 869-5199
OREGON
828 19th Avenue, N.W.
Portland, OR 97209
(503) 222-1823
WISCONSIN
Lincoln Plaza Shopping Ctr.
2245 S. 108th St. West Allis, WI
53227
(414) 541-4776
CUSTOMER’S RECORD
Date Purchased
When you need service: Send
complete tool (prepaid) to one
of the Makita Factory Service
Centers listed, or to an Authorized
Makita Service Center. Be sure
to attach a letter to the outside of
the carton detailing the problem
with your tool.
Dealer’s Name & Address
Model No.
Serial No.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles.
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of
defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of
Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective
workmanship or material, Makita will repair (or at our option, replace) without charge.
This Warranty does not apply where:
• repairs have been made or attempted by others:
• repairs are required because of normal wear and tear:
• the tool has been abused, misused or improperly maintained:
• alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING
AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF
“MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,” AFTER THE ONE YEAR TERM OF THIS
WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied
warranty lasts, so the above limitation may not apply to you.
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi 446-8502 Japan
883840C061
Download from Www.Somanuals.com. All Manuals Search And Download.
|