Supported Capacity*:
Charger Input Power:
Adapter Input:
100 to 20,000mAh
12V 2.0A
100-240V 50/60Hz
* Always ensure that the batteries can accept the programmed rates.
MH-C9000
WizardOne Charger-Analyzer
Thank you for purchasing the Powerex MH-C9000
Charger-Analyzer. Read these instructions carefully
and thoroughly before operating this unit. IMPORTANT
SAFETY INSTRUCTIONS. READ AND SAVE THESE
INSTRUCTIONS.
OPERATING THIS PRODUCT INCORRECTLY CAN
CAUSE DAMAGE TO THE BATTERIES.
READ MANUAL COMPLETELY BEFORE USE.
GENERAL BATTERY EDUCATION
GENERAL PRECAUTIONS
•
Do not charge battery cells other than NiMH or NiCD. Please check
with the battery manufacturer to ensure it can accept the
programmed charging and discharging rates. Do not expose the unit
to rain or moisture due to the risk of fire.
What is 0.1C, 0.2C, etc?
“C” stands for the battery capacity and the number in front of it is the
fraction of the battery capacity. For example, 0.1C means 0.1 times the
capacity for the battery. For a 2700mAh battery, 0.1C would be 0.1 times
2700mAh which equals 270mA.
•
•
Do not operate the charger if it appears damaged in any way.
Always place the battery cells with positive tip facing the top.
Incorrect polarity may cause fire or explosion. Observe polarity
diagrams located on the charger.
Choosing the right charging & discharging rate
•
Do not allow the unit to be exposed to direct sunlight. Operate in
well-ventilated area. Do not place unit on the carpet.
Charging at a rate below 0.33C and above 1.0C is not
recommended.
•
•
Do not allow the battery terminals to become shorted.
To reduce the risk of damage to the power cord, always pull by
connector rather than the cord.
Charging too slow may prevent the charger from terminating correctly.
Charging too fast may damage the battery.
•
Use only the supplied adapter or optional regional and car adapter
offered by Maha Energy. Using third party accessories voids the
product warranty.
Typically speaking, slower charging rate will yield better battery
performance but requires longer time. Faster charging rate may not
charge as fully and battery temperature can be higher.
Battery Matching
FEATURES & SPECIFICATIONS
In most devices, usually two or more batteries are used together. When
batteries are used in a series, the performance is limited by the worst
one. In other words, one poorly performing battery can significantly
reduce the device runtime.
•
•
•
•
Four independent slots for AA or AAA NiMH batteries.
Backlit LCD display.
Battery matching refers to grouping batteries with similar “actual”
capacity. To perform this, use the Refresh & Analyze mode to determine
the battery capacity. Group batteries with capacity within about +/- 5% of
the rated capacity.
Digitally displays capacity, voltage, time and current.
Five modes of operation: Charge, Refresh & Analyze, Break-In,
Discharge and Cycle.
•
•
•
19 selectable charging current from 0.2A to 2.0A.
10 selectable discharging current from 0.1A to 1.0A.
Worldwide power supply.
Battery “Forming”
New batteries and those stored for extended period become chemically
deactivated. Battery forming is a charge-discharge-charge cycle which
forces a full charge into the battery at a very slow rate. This process
activates the battery. In certain cases, it needs to be repeated two or
three times.
Charging Current:
Programmable from 0.2A to 2.0A in
increments of 0.1A
Battery forming can be performed using the Break-In mode.
Topoff Charging Current:
100mA
Maintenance Charging
Current:
10mA
Discharge Termination:
Voltage 1.00V
Discharging Current:
Programmable from 0.1A to 1.0A in
increments of 0.1A
Capacity Storage Memory:
12 (Cycle mode only)
PRINTED IN TAIWAN A03-3713420-496
Download from Www.Somanuals.com. All Manuals Search And Download.
If REFRESH & ANALYZE mode is selected:
The charger will prompt for the charging rate by flashing “SET CHG
RATE.” Use the UP and DOWN key to choose the desired current.
Press ENTER to make the selection.
Then it will prompt from the discharging rate by flashing “SET
DISCHG RATE.” Follow the same procedure as above.
6. To ensure safety, the charger performs an “impedance check” at the
beginning of the program. If the battery fails this test, “HIGH” would
be displayed and program will be terminated.
If BREAK-IN mode is selected:
The charger will prompt for the battery capacity in order to calculate
the charging and discharging rate automatically. “SET BATTERY
CAPACITY” will flash. Use the UP and DOWN key to choose the
desired current. Press ENTER to make the selection.
Typically alkaline and extremely aged battery will fail this test. For a
rechargeable battery, it is recommended for the battery to be
discarded.
NOTE: This test is not performed for the discharge mode.
If this detection is believed to be incorrect, a discharge can be
performed first.
7. While executing the programmed function, the charger will display
the battery status for each occupied slot consecutively. The screen
will first show an arrow below the active bank and display the
information. The next slot(s) occupied follows.
If DISCHARGE mode is selected:
Press the SLOT button at anytime will jump to the next occupied
slot. Press this button multiple times if necessary to go to the desired
slot.
The charger will prompt for the discharging rate by flashing “SET
DISCHG RATE.” Use the UP and DOWN key to choose the desired
current. Press ENTER to make the selection.
The following information is displayed on the screen:
Current:
This is the number followed by the unit “MA.” This is the
approximate charging or discharging current. Note that this number
will go up and down due to the pulse charging.
If CYCLE mode is selected:
The charger will prompt for the charging rate and discharging rate
similar to the other modes. In addition, it will also prompt for the
number of cycles to be performed by flashing “SET CYCLES.” Use
the UP and DOWN keys to choose the desired cycles. Press
ENTER to make the selection.
Capacity:
This is the number followed by the unit “MAH.” This is the
accumulated charging or discharging capacity. If it is charging
capacity, “CHARGE” in black box will be shown. If it is discharging
capacity, “DISCHG” in black box will be shown.
PRINTED IN TAIWAN A03-3713420-496
Download from Www.Somanuals.com. All Manuals Search And Download.
For CYCLE mode, the discharge capacity of the final cycle is
displayed. “CYCLE HISTORY” icon will also be shown. Use the UP
and DOWN key to access discharge capacity for all the cycles
performed.
The capacity information will be stored as long as the battery is
inserted in the charger. It will be lost upon removal of the battery.
Note the charging capacity is usually higher than the actual capacity
of the battery owing to some energy lost as heat. Charging capacity
cannot be used to judge the performance the battery. Instead, it can
only be used to determine the progress of the charger. It is normal
for this number to exceed the actual capacity by as much as 20-
30%.
THREE-YEAR LIMITED WARRANTY
Maha Energy Corp. warrants this product against defects in materials and
workmanship as follows: For the first three years from the date of
purchase, Maha Energy Corp. will repair or replace the unit at its option
without charge for parts or labor. After the indicated period of three years,
the product owner is subject to pay for repair and parts fee.
Time:
This limited warranty is non-transferable. It does not cover damage or
failures caused by or attributable to natural disaster, abuse, misuse,
improper or abnormal usage, faulty installation, improper maintenance,
lightning, or other incidences of excessive voltage, or any repairs or
tampering by other than by Maha Energy Corp. or its Authorized Service
Centers. This warranty will be voided if the serial number (if applicable),
model number, or brand has been wholly or partially removed or erased.
Repair or replacement under the terms of this warranty does not extend
the duration of this warranty. Should this product be proven defective in
workmanship or material, the consumer's sole remedies shall be such
repair or replacement as provided by the terms of this warranty. Under no
circumstances shall Maha Energy Corp. be liable for any loss or damage,
direct, consequential, or incidental, arising out of the use of or inability to
use this product. Some states do not allow limitations on how long an
implied warranty lasts or the exclusions or limitations of incidental or
consequential damages, so the above limitations or exclusions may not
apply to the product owner. This warranty gives the product owner
specific legal rights. The product owner may also have other rights, which
vary from state to state.
This is the number followed by the unit “MIN.” This is the time
elapsed for the particular routine such as charging, discharging or
rest in the program.
Voltage:
This is the number followed by the unit “VOLT.” It represents the
offline battery voltage. If you compare this with a voltmeter while
charging, the values will not match as a voltmeter is unable to
measure the offline battery voltage.
To obtain warranty service, contact Maha Energy Corp. Service
Department at 1-800-376-9992 or 1-909-392-1568. When returning the
unit for warranty service, the product owner must obtain a return
merchandise authorization number from a service representative. In
addition, please include a copy of the sales receipt, a brief description of
the symptoms, name, address, and phone number. Then deliver or ship
the product, postage and shipping costs prepaid (insurance suggested),
to:
Maha Energy Corp. Service Department
1647 Yeager Ave. La Verne, CA 91750
All warranty repair or replacement will be returned to the customer using
Ground service. If a faster carrier method is requested, the product owner
must pay the cost difference over the Ground service charge. Maha
Energy Corp. is not liable for products lost or damaged unit during
shipment.
At any given time during the program, the charger will either be
charging, discharging or resting. The LCD displays the action in
black boxes containing CHARGE, DISCHG, or REST.
8. If CYCLE mode is selected, it is also possible to review the battery
capacity of finished cycle after the completion of the first cycle.
Press the UP or DOWN key while the active slot is in the cycle mode
will display the discharge capacity for that cycle. The LCD will also
display “CYCLE HISTORY.”
9. When the program for a slot is completed, DONE will displayed to
the right of the bank number. With the exception of DISCHARGE
mode, topoff charge and trickle charge (continuous) will be applied.
Available At:
Thomas Distributing
Tel: 1-800-821-2769
For CHARGE mode, the total charged capacity will be displayed.
For REFRESH & ANALYZE, BREAK-IN, DISCHARGE mode, the
total discharge capacity will be displayed. “AVAILABLE CAPACITY”
icon will also be shown.
MAHA ENERGY CORP.
Copyrighted ® 1998-2007 Maha Energy Corp.
PRINTED IN TAIWAN A03-3713420-496
Download from Www.Somanuals.com. All Manuals Search And Download.
|