Magnavox VCR VCRVR401BMG User Manual

VCR  
VR401BMG  
VR601BMG  
Video Ca ssette Recorder  
Hookup Pa ges  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Hookups Without a Cable Box/Direct Broadcast System (contd) 7  
3
Connect the RF coaxial cable (supplied) to the O UT Jack on the back of the  
VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on  
type (supplied) or screw-on type of coaxial cable, whichever you prefer.)  
AUDIO  
ANT  
L
IN  
OUT  
IN  
R
VIDEO  
OUT  
Antenna  
or Cable  
CH3 CH4  
OUT  
IN  
ANT  
AUDIO  
L
IN  
75  
ANT /  
CABLE  
75⍀  
ANT  
CABLE  
/
IN  
OUT  
R
OUT  
VIDEO  
ANTENNA IN Jack  
(on back of TV)  
exam ple only  
CH4  
IN CH3  
OUT  
RF coaxial cable  
4
Plug in the TV and the VCR.  
5
Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever  
channel is not used or least used in your area. Set the TV to the sam e channel. For  
example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on  
channel 03.  
AUDIO  
ANT  
L
IN  
OUT  
IN  
R
CH 4  
or  
CH 3  
VIDEO  
OUT  
CH3 CH4  
OUT  
IN  
ANT  
AUDIO  
L
IN  
CH3 / CH4  
Switch  
IN  
OUT  
R
OUT  
VIDEO  
CH4  
IN CH3  
CH3  
CH4  
OUT  
6
You are ready to turn on the VCR. Please go to page 11 before turning on the  
VCR.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8 Hookups With a Cable Box/Direct Broadcast System  
There are two ways to connect your Cable Box/DBS to the VCR. With this connection:  
You may view any channel.  
You must select channels at the Cable Box/DBS. Channels cannot be changed at the VCR.  
You may not view a channel other than the one you are recording.  
You may not program channels at the VCR.  
You can only program a timer recording for one channel at a time. Set the TV and the VCR to the Cable  
Box/DBS output channel (channel 03 or 04); set the CH3/CH4 switch to the same channel. Set your Cable  
Box/DBS to the channel you want to record. When you enter the channel you want to record in a timer  
recording, select channel 03 or 04 (the Cable Box/DBS output channel). (This is step 5 on page 29.) Leave the  
Cable Box/DBS on for a timer recording.  
VCR  
Cable Box/DBS  
2
1
75  
ANT /  
CABLE  
IN  
OUT  
ANT  
AUDIO  
L
IN  
OUT  
RF coaxial  
cable  
R
VIDEO  
OUT  
Cable  
Signal  
CH3 CH4  
IN  
OUT  
TV’s  
ANTENNA IN  
Jack  
RF coaxial  
cable  
3
Connections  
1
Connect a Cable signal to the IN Jack on the Cable Box/DBS.  
2
Use an RF coaxial cable (supplied) to connect the OUT Jack on the Cable  
Box/DBS to the ANT(enna) IN Jack on the VCR.  
3
Use a second RF coaxial cable to connect the OUT Jack on the VCR to the  
TV’s ANTENNA IN Jack.  
Recording/Viewing Any Channel  
1
With the VCR on and in VCR position (the VCR/TV light will appear on the dis-  
play panel), use the CHANNEL o/p buttons to set the VCR to the  
Cable Box/DBS output channel (channel 03 or 04). Set the CH3/CH4  
switch to the sam e channel.  
2
Set the TV to the sam e channel to which you set the VCR.  
3
Select the channel you want to view/record at the Cable Box/DBS.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Hookups With a Cable Box/Direct Broadcast System (contd) 9  
With this connection:  
You may watch one channel while recording another.  
You may not record scrambled channels.  
VCR  
1
Cable Box/DBS  
75  
ANT /  
CABLE  
2
AUDIO  
L
ANT  
IN  
OUT  
I
R
IN  
OUT  
VIDEO  
OUT  
IN CH3  
OUT  
RF coaxial  
cable  
Cable  
Signal  
TV’s ANTENNA  
IN Jack  
RF coaxial  
cable  
3
Connections  
1
Connect a Cable signal to the VCR’s ANT(enna) IN Jack.  
2
Use an RF coaxial cable (supplied) to connect the OUT Jack on  
the VCR to the IN Jack on the Cable Box/DBS.  
3
Use a second RF coaxial cable to connect the OUT Jack on the  
Cable Box/DBS to the ANTENNA IN Jack on the TV.  
Recording O ne Channel/W atching Another  
1
Put the Cable Box/DBS on the sam e channel as the  
VCR’s CH3/CH4 switch. Set the TV to the Cable  
Box/DBS output channel (03 or 04).  
Then, with the VCR in VCR position (the VCR/TV light will  
appear on the display panel), use the CHANNEL o/p but-  
tons to select the channel you want to record at the  
VCR. Start the recording.  
Helpful Hint  
2
Press the VCR/TV button once to put the VCR in TV  
position. (The VCR/TV light will disappear.)  
• When you play a tape, make sure  
the Cable Box/DBS is set to the  
same channel as the CH3/CH4  
switch on the VCR. Set the TV to  
the Cable Box/DBS output channel  
(03 or 04).  
3
Select the channel you want to watch at the Cable  
Box/DBS.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10 Hookups with a Stereo TV  
antenna or  
cable to  
ANT(enna)  
IN Jack  
VR601BMG  
1
AUDIO  
L
ANT  
IN  
OUT  
IN  
R
VIDEO  
OUT  
CH3 CH4  
OUT  
IN  
Audio and Video  
IN Jacks on TV  
VIDEO (yellow) and  
AUDIO (red and white)  
OUT Jacks  
Video Cable  
2
Stereo Audio Cable  
3
3
antenna or  
VR401BMG  
cable to  
ANT(enna)  
IN Jack  
1
ANT  
IN  
AUDIO  
IN  
OUT  
OUT  
CH3 CH4  
Audio and Video  
IN Jacks on TV  
VIDEO  
VIDEO (yellow) and  
AUDIO (white) OUT Jacks  
Video Cable  
2
Audio Cable  
Audio and Video cables are not supplied.  
1
Connect the antenna or cable to the ANT(enna) IN Jack on the back of the VCR.  
2
Connect a video cable to the yellow VIDEO O UT Jack on the back of the VCR. Then, connect  
the other end of the video cable to the VIDEO IN Jack on your TV.  
3
VR601BMG: Connect a stereo audio cable to the red and white AUDIO OUT Jacks on the back  
of the VCR, m atching cable colors to the jack colors. Then, connect the other end of the audio  
cable to the AUDIO IN Jacks on your TV, again m atching cable colors to the jack colors.  
VR401BMG: Connect an audio cable to the white AUDIO OUT Jack on the back of the VCR.  
Then, connect the other end of the audio cable to the AUDIO IN Jack on your TV.  
(If your TV has Right and Left AUDIO IN Jacks, you must use a “Ysplitter audio cable as illustrated to deliver  
audio to the TV’s right and left channels.) This hookup will not give you stereo sound. To get stereo sound, use  
the connections on pages six - seven and select the channel to be viewed at the TV (with the VCR turned off).  
4
Turn on your TV, making sure it is in Line Input mode. Please refer to your TV owners manual for details.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22 Front Panel  
STO P/EJECT Button  
Press once to stop the tape. When playback is stopped,  
press to eject the tape. Press to select an item in the menu.  
Rem ote Sensor  
PAUSE Button  
Receives a signal from your  
remote control so you can oper-  
ate your VCR from a distance.  
While recording, press to pause the recording. Press  
again to resume recording. Details are on page 25. You  
can not pause a One-Touch Recording. During tape  
playback, press to freeze the picture. Press again to  
resume playback. Details are on page 36.  
PO W ER Button  
Press to turn the  
VCR power on and off.  
REW (ind) Button  
VIDEO In Jack  
When playback is stopped, press to  
rewind the tape at high speed.  
During playback, press to rewind the  
tape while the picture stays on the  
screen. Details are on page 36. Press  
to return to a previous menu.  
Connect a cable com-  
ing from the video  
out jack of a cam-  
corder, another VCR,  
or an audio-visual  
source (laser disc  
player, video disc  
player, etc.) here.  
Details are on page 32.  
PLAY Button  
Press to play a tape. Press to release Slow,  
Search, or Still mode and return to play-  
back. Details are on page 36. Press to  
select an item in the menu.  
VR601BMG  
PLAY  
PAUSE  
STOP/EJECT  
REC/OTR  
REW  
F.FWD  
POWER  
VCR/TV  
CST.IN  
TIMER  
REC  
MENU  
STATUS/EXIT  
CHANNEL  
VIDEO  
L - AUDIO -R  
POWER  
VCR/TV  
CHANNEL (p/o) Buttons  
AUDIO In Jacks  
Press to change channels at the VCR.  
Or, press to adjust the tracking of a  
tape during normal playback or slow  
motion playback. Also, press to  
Connect audio cables com-  
ing from the audio out jacks  
of a camcorder, another  
VCR, or an audio source  
here. Details are on page 32.  
The VR601BMG is shown  
here. The VR401BMG has  
only one AUDIO IN jack.  
remove vertical jitter in a Still picture.  
REC(ord)/O TR Button  
Press once to start a recording. Press  
repeatedly to start a One-Touch  
Recording. Details are on page 27.  
VCR/TV Button  
MENU Button  
Press to select VCR or TV position.  
VCR Position  
Press to access the VCR menu.  
Use to watch a tape, to watch a program  
while recording it, or to watch a TV pro-  
gram (changing channels at the VCR). When  
the VCR/TV light appears on the display  
panel, the VCR is in VCR position.  
TV Position  
Use to watch TV (changing channels at the  
TV) or to watch one program while record-  
ing another. When the VCR/TV light does  
not appear on the display panel, the VCR is  
in TV position.  
STATUS/EXIT Button  
Press to access or remove the on-screen status display.  
Details are on page 20. Press to exit on-screen menus.  
F.FW D (Fast Forward) Button  
When playback is stopped, press to fast forward the tape at  
high speed. During tape playback, press to fast forward the  
tape while the picture stays on the screen. Details are on  
page 36. Press to advance to the next menu or to change  
the setting of an item in the menu.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rear Panel 23  
ANT(enna) IN Jack  
Connect your antenna or cable  
here. Details are on pages six-10.  
AUDIO IN Jacks  
Connect audio cables coming from the  
AUDIO OUT Jacks of a camcorder,  
another VCR, or an audio source here.  
Details are on page 32.  
The VR601BMG is shown here. The  
VR401BMG has only one AUDIO IN jack.  
AUDIO OUT Jacks  
Connect audio cables going to the AUDIO IN  
Jacks of a camcorder, another VCR, or an audio  
system here. Details are on pages 32 and 38.  
The VR601BMG is shown here. The VR401BMG has  
only one AUDIO OUT jack.  
VR601BMG  
AUDIO  
L
ANT  
IN  
IN  
OUT  
R
VIDEO  
OUT  
CH3 CH4  
OUT  
IN  
VIDEO O UT Jack  
Connect a video cable going to the VIDEO  
IN Jack of a camcorder, another VCR, or an  
audio-visual system (monitor, laser disc play-  
er, video disc player, etc.) here. Details are on  
pages 32 and 38.  
CH3/CH4 Switch  
Set to channel 3 or 4  
to use your TV with  
your VCR. Details are  
on pages six-nine.  
VIDEO IN Jack  
Connect a video cable coming  
from the VIDEO OUT Jack of a  
camcorder, another VCR, or an  
audio-visual source (laser disc  
player, video disc player, etc.)  
here. Details are on page 32.  
AC Power Cord  
Connect to a stan-  
dard AC outlet to  
supply power to the  
VCR.  
O UT Jack  
Use the supplied RF coaxi-  
al cable to connect this  
jack to the ANTENNA IN  
Jack on your TV, Cable  
Box, or Direct Broadcast  
System. Details are on  
pages six-nine.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
32 Rerecording (Tape Duplication)  
The instructions on this page show you how to copy tapes. The illustration uses two VR601BMG VCRs.  
Different VCRs may operate differently. To duplicate a tape, make the connections shown, then follow steps 1-7.  
1. Audio cables from AUDIO O UT Jacks  
of VCR 1 to AUDIO IN Jacks of VCR 2  
VCR 1  
Playing VCR  
VCR 2 - Recording VCR  
AUDIO  
ANT  
ANT  
AUDIO  
L
L
IN  
IN  
OUT  
IN  
OUT  
IN  
R
R
VIDEO  
VIDEO  
OUT  
OUT  
CH3 CH4  
CH3 CH4  
OUT  
IN  
IN  
OUT  
3. RF coaxial cable  
from the OUT jack of  
VCR 2 to the TV’s  
ANTENNA IN Jack  
2. Video cable from VIDEO O UT Jack  
of VCR 1 to VIDEO IN Jack of VCR 2  
Audio and Video cables are not supplied.  
1
Make the connections shown above.  
Helpful Hints  
2
VCR 1 will play your tape. Put a prerecorded tape in VCR 1.  
If you use the AUDIO and VIDEO IN  
Jacks on the back of VCR 2, press  
Number buttons 0, 0, 1 at step 5.  
AV REAR will appear on the screen.  
If you use the AUDIO and VIDEO In  
Jacks on the front of VCR 2, press  
Number buttons 0, 0, 2 at step 5.  
AV FRONT will appear on the  
screen.  
Unauthorized recording of copyright-  
ed television programs, video tapes,  
or other materials may infringe on  
the rights of copyright owners and  
violate copyright laws.  
If a program has copyright protec-  
tion, it may not record clearly.  
These instructions show you how to  
copy tapes using two VCRs like  
yours. Different VCRs may operate  
differently.  
3
VCR 2 will record your tape. Insert a blank tape in VCR 2. The  
VCR must be in VCR position. (The VCR/TV light will appear on the  
display panel. If it does not, press the VCR/TV button once.)  
4
Turn on the TV and set it to channel 03 or 04, whichever  
channel the CH3/CH4 switch on VCR 2 is set to.  
5
Point the rem ote control at VCR 2. Press the Num ber  
buttons 0, 0, 1 or 0, 0, 2. (See Helpful Hints at right.)  
6
Press the SPEED button to select SP or SLP at VCR 2.  
The VCR in the figure above is the  
VR601BMG. If you have the  
VR401BMG, use a single-plug audio  
cable to connect the AUDIO OUT  
jack on VCR 1 to the AUDIO IN jack  
on VCR 2.  
7
Press the PLAY button on VCR 1 and the REC(ord)/O TR  
button on VCR 2 at the sam e tim e.  
To stop recording, press the STOP/EJECT button on VCR 1, then  
press the STOP/EJECT button on VCR 2.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

La Crosse Technology Clock 515 1316 User Manual
Lennox Hearth Stove SDVCS User Manual
Lenovo Laptop 24684XU User Manual
LG Electronics Flat Panel Television 19LH20 User Manual
Lucent Technologies Network Card MRT 36H User Manual
Magellan GPS Receiver GPS 300 User Manual
Magic Chef Microwave Oven MCD775W User Manual
Mellerware Hot Beverage Maker 2200W User Manual
Microsoft Window A2xx User Manual
Midland Radio Camcorder XTC 200 User Manual