CCZ130comb 4/5/99 7:31 PM Page 1
Color TV with built-in VCR
CCZ130AT
O wner’s Manual
Im portant!
Return your W arranty Registration
Card within 10 days. See why inside.
Use photograph
(same as carton)
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:31 PM Page 3
Introduction 3
W elcom e to your TV/VCR owner’s m anual.
This manual has six sections: Setting Up Your TV/VCR; Description of Controls; Basic Operations;
Recording Options; Playing Options; and Information You May Need. The instructions explain all of the
TV/VCR’s features, which are listed below.
Features
• A-B Repeat Play
• Automatic Channel Setup
• Automatic Operation Features
• Automatic Tracking Adjustment
• Closed Caption
• Daylight-Saving Time
• High Quality (HQ) System
• On-Screen displays in English or Spanish
• On-Screen Menu Programming, accessible with remote control
or front panel buttons
• One-Touch Recording
• Real-Time Counter
• Remote Control
• Repeat Play
• Sleep Timer
• SmartClockTM
• Special Effects Playback: Forward and Reverse Searching; Still
• Timer Recording
Safety Precautions
Warning: To prevent fire or shock hazard, do not expose this
equipment to rain or moisture.
FCC Warning: Any unauthorized changes or modifications to this
equipment void the user’s authority to operate it.
This TV/VCR, equipped with a High Quality (HQ) system, is com-
patible with existing Video Home System (VHS) equipment.
Philips Consum er Electronics Com pany recommends that
you use only video cassette tapes that have been tested and
inspected for use in two, four, six, and eight hour VCRs, and
which are labeled with the
mark. The use of tapes that
have not been inspected for use in two, four, six, and eight hour
VCRs may result in poor picture quality and excessive deposits on
the video heads, which may not be covered by the warranty if
damage occurs.
Note to the Cable TV System Installer: This reminder is
provided to call the Cable TV system installer’s attention to
Article 820-40 of the National Electrical Code, which provides
guidelines for proper grounding – in particular, specifying that the
cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as possible.
SmartClockTM is a trademark of Philips Consumer Electronics
Company.
Copyright 1998 Philips Consumer Electronics Company. All rights
reserved.
Helpful Hint
• Before doing anything else, record
the TV/VCR’s model and serial num-
bers in the spaces provided on page
two. These numbers will help us
assist you if you ever call for help.
om
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:31 PM Page 4
4 Table of Contents
Setting Up Your TV/VCR
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Before Using the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Hooking Up the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 7
Turning On the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Automatic Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 11
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 17
Daylight-Saving Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Time Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Description of Controls
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Remote Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 - 23
Adjusting the Picture Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 - 25
On-Screen Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Basic O perations
Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Recording O ptions
One-Touch Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Rerecording (Tape Duplication) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 - 35
Defeat Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Playing O ptions
Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Closed Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 - 39
Volume Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
A - B Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 - 43
Real-Time Counter Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Automatic Operation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Playback Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Inform ation You May Need
Specifications / Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 - 49
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:31 PM Page 5
Before Using the TV/VCR 5
Putting Batteries in the Rem ote Control
1
Rem ove the battery com partm ent lid on the bottom of
the rem ote control by sliding it in the direction of the
arrow.
1
2
3
2
Place two AA batteries inside the battery com partm ent
with their and ends aligned as indicated.
+
–
3
Replace the battery com partm ent lid.
Rem oving the Shipping Card
● A shipping card may be inserted in the cassette compartment of
the TV/VCR. Before you insert a cassette tape, remove the ship-
ping card. To remove the card, open the cassette compartment
door, then grasp the adhesive tape and remove the card.
Erasure Prevention
Video cassette tapes have record tabs to ensure that recordings
are not accidentally erased.
1
2
1
To prevent accidental erasure, break off the tab with a
screwdriver.
2
To record again, cover the hole with cellophane tape.
Using the Rem ote Control
● Point the remote control at the TV/VCR’s remote sensor.
● Do not put objects between the remote control and the
TV/VCR.
VCR Maintenance
● In this TV/VCR, use only tapes with the
mark.
● Make sure any light adhesive stick-on notes are removed from
the video cassette tape before putting the tape in the TV/VCR.
Removable labels like these can jam the TV/VCR.
● Periodic maintenance is required to maintain your TV/VCR’s
excellent performance. This TV/VCR has an automatic head
cleaning system. However, the video heads will eventually
require cleaning or replacement. Cleaning or replacement of the
video heads should be performed by an authorized service cen-
ter.
Helpful Hints
• The remote control and its batteries
are supplied.
• Do not mix alkaline and man-
ganese batteries.
• Do not mix old and new batteries.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:31 PM Page 6
6 Hooking Up The TV/VCR
1
Hook up your TV/VCR using one of the connections shown.
Connect a Cable signal
or an antenna to the
ANT(enna) Jack.
A.
Hooking Up Your TV/VCR
W ith a Cable Signal or
O utdoor Antenna
ANT.
ANT.
Connect the Cable signal to
the IN Jack on the Cable Box.
B.
Hooking Up Your TV/VCR
W ith a Cable Box
Connect an RF coaxial cable (75-
To view any channel, set the
TV/VCR to the Cable Box output
channel (channel 03 or 04). Then,
select channels at the Cable Box.
ohm, not supplied) to the OUT Jack
on the Cable Box and to the
ANT(enna) Jack on the TV/VCR.
IN
OUT
ANT.
ANT.
Rod Antenna
(not supplied)
C.
Hooking Up Your TV/VCR
W ith an Indoor Antenna
To install a rod antenna (not sup-
plied), push the stem of the antenna
into the antenna hole on the top of
the TV/VCR. Connect the antenna
wire to the ANT(enna) Jack on the
back of the TV/VCR as shown.
Extend the antenna and adjust its
length, direction, and angle for the
clearest picture.
ANT.
ANT.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 7
Hooking Up The TV/VCR (cont’d) 7
D.
Hooking Up Your
TV/VCR to Another
Video Source
(VCR or Cam corder)
You may need this connection
if you want to copy tapes.
Details are on page 31.
Use an Audio cable to connect the AUDIO
OUT Jack on the VCR to the AUDIO Jack
on the front of the TV/VCR.
AUDIO/VIDEO OUT
Jacks on VCR
3CH
IN
4CH
AUDIO VIDEO
ANT.
OUT
OUT
IN
AUDIO VIDEO
AUDIO
VIDEO
STOP/EJECT
REW
PLAY
F.FWD
REC/OTR
CHANNEL
VOLUME
POWER
E
3CH
IN
4CH
AUDIO VIDEO
ANT.
OUT
OUT
IN
AUDIO/VIDEO Jacks
on front of TV/VCR
Use a Video cable to connect the VIDEO OUT Jack on
the VCR to the VIDEO Jack on the front of the TV/VCR.
2
Plug in the TV/VCR.
3
Before you turn on the TV/VCR, go to page eight.
Helpful Hints
• Before connecting an antenna or cable signal to the ANT(enna) Jack, make sure the pin is not bent. If the pin is
bent, straighten it as illustrated, then connect the antenna or cable signal to the ANT(enna) Jack.
• A rod antenna (not supplied) is available from Philips Service Solutions Group. The part number is 4835 303
37006. To order, call 1-800-851-8885.
• Audio and video cables are not supplied.
Bent pin
Crooked Pin
Straight Pin
Plug
Cable
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 8
8 Turning On the TV/VCR
Before you turn on the TV/VCR, make sure there are batteries in
the remote control and the TV/VCR is hooked up correctly.
The instructions on this page work only when you turn on the
TV/VCR for the first time.
3
1
POWER
MENU
STATUS/EXIT
CLEAR
1
1
2
3
MEMORY
Press the PO W ER button. The TV/VCR will come on and the
screen shown below will appear.
4
7
5
8
0
6
9
CHANNEL
ALT.CH
SELECT LANGUAGE
> ENGLISH
ON
+100
5
2
ESPAÑOL
SLEEP
SPEED
SELECT KL OR
PRESS MENU TO CONTINUE
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
4
STOP/
PAUSE/STILL
2
Press the PLAY/K button or the STO P/L button to select
English or Spanish on-screen displays.
3
Press the MENU button. The screen shown below will appear.
CONNECT ANTENNA OR CABLE
TO TVCR
THEN PRESS
B
TO END PRESS EXIT
Helpful Hints
4
• If you do not see any on-screen dis-
plays when you turn on the TV/VCR,
check your hookups, then try again.
If you still do not see any on-screen
displays, follow the steps on pages
nine - 10 to select a language and
set up channels.
• To skip step 2, press the MENU
button. All on-screen displays will be
in English. To skip step 4, press the
STATUS/EXIT button. Channels will
not be set up, and CHANNELS
NOT SET will appear on-screen
briefly.
Press the FF/SEARCH B button to begin autom atic chan-
nel setup. The TV/VCR will memorize all available channels.
When channels are set, CHANNELS ARE SET will appear on-
screen briefly. Then the TV/VCR will go to the lowest channel
programmed.
(If you try to set up channels when there is no antenna or cable
connected to the TV/VCR, programming will appear to take place,
but eventually a NO TV SIGNALS ... message will appear on-
screen. Connect an antenna or cable to the TV/VCR, then try
again. You may need to follow the steps on page 10 instead.)
5
Use the CHANNEL o/p buttons or the Num ber buttons
on the rem ote control to select a TV/VCR channel. Use
the VO LUME o/p buttons to adjust the sound.
• You cannot set up channels if you
are using a Cable Box.
• Line Input mode will always be
stored in the TV/VCR’s memory as
channel 00. When you select chan-
nel 00, A/V IN will appear on-
screen briefly. Press the CHANNEL
o/p buttons or Number buttons to
select another channel.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 9
Language Selection 9
Follow the steps below to change the language of the on-screen
displays.
1
Press the MENU button.
5
1
POWER
MENU
STATUS/EXIT
CLEAR
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
1
2
3
MEMORY
4
7
5
8
0
6
9
REMINDER
BRIGHTNESS
CHANNEL
ALT.CH
+100
SLEEP
SPEED
2
VOLUME
MUTE
Press the PLAY/▲ button or the STO P/▼ button to select
PRIM. SETUP. Then, press the FF/SEARCH B button.
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
STOP/
PAUSE/STILL
PRIMARY SETUP
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME BAR
SET CLOCK
[ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
3
Press the PLAY/▲ button or the STO P/▼ button to
choose SELECT LANGUAGE. Then, press the
FF/SEARCH B button.
2-4
SELECT LANGUAGE
> ENGLISH
ESPAÑOL
ON
SELECT KL
TO END PRESS EXIT
4
Press the PLAY/▲ button or the STO P/▼ button to select
ENGLISH or ESPAÑO L (Spanish).
Helpful Hint
• If you accidentally select Spanish
on-screen displays and need English
on-screen displays:
5
Press the STATUS/EXIT button.
1) Press the MENU button.
2) Press the PLAY/o button or the
STOP/p button to select PREPARA-
CION, then press the
FF/SEARCH B button.
3) Press the PLAY/o button or the
STOP/p button to select SELEC-
CION IDIOMA, then press the
FF/SEARCH B button.
4) Press the PLAY/o button or the
STOP/p button to select ENGLISH.
5) Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 10
10 Automatic Channel Setup
Although the TV/VCR may automatically memorize the channels
you receive when you turn it on for the first time, you may set up
channels again by following the steps below.
Wait for the TV/VCR to set up
channels.
5
1
1
Press the MENU button.
TO ADJUST PRESS { /
B
CABLE
>
INPUT
EXIT
POWER
MENU
STATUS/EXIT
CLEAR
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
1
2
3
MEMORY
4
7
5
8
0
6
9
CHANNEL
ALT.CH
+100
2
SLEEP
SPEED
Press the PLAY/▲ button or the STO P/▼ button to select
INPUT. Press the REW (ind)/SEARCH { button or the
FF/SEARCH B button until ANTENNA or CABLE
(whichever you have) appears beside INPUT.
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
STOP/
PAUSE/STILL
3
TO ADJUST PRESS { /
B
CABLE
>
INPUT
EXIT
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
3
2&4
Press the STO P/▼ button repeatedly to select PRIM.
SETUP, then press the FF/SEARCH B button.
PRIMARY SETUP
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME BAR
SET CLOCK
[ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
4
Press the PLAY/▲ button or the STO P/▼ button to select
AUTO PRO GRAMMING, then press the FF/SEARCH
B
button. AUTO PROGRAMMING MEMORIZED CH ... will
appear on-screen. The TV/VCR will memorize all available chan-
nels.
Helpful Hints
• Line Input mode will always be
5
stored in the TV/VCR’s memory as
channel 00. You cannot delete it.
• You cannot program channels when
the TV/VCR is on channel 00 (A/V
INPUT will appear beside INPUT at
step 2). Select ANTENNA or CABLE
at step 2.
W ait for a few m inutes. When setup is complete, CHANNELS
ARE SET will appear on-screen. Then the programming of the
lowest channel number placed in the TV/VCR’s memory will
appear on-screen. Now, when you press the CHANNEL o/p
buttons, you will scan only through channels you receive.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 11
Automatic Channel Setup (cont’d) 11
Adding/Deleting Channels
1
Press the MENU button.
TO ADJUST PRESS { /
B
CH123
1
POWER
MENU
STATUS/EXIT
CLEAR
5
3
SAVED
>
CHANNEL
INPUT
1
2
3
MEMORY
EXIT
PRIM. SETUP
VCR PROGRAM
VCR SETUP
4
7
5
8
0
6
9
CHANNEL
ALT.CH
+100
2
SLEEP
SPEED
Press the PLAY/▲ button or the STO P/▼ button to select
CHANNEL, then press the FF/SEARCH B button.
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
4
TO ADJUST PRESS { /
CH123
B
2
STOP/
PAUSE/STILL
SAVED
>
CHANNEL
INPUT
EXIT
PRIM. SETUP
VCR PROGRAM
VCR SETUP
3
Press the Num ber buttons or the CHANNEL ▲/▼ but-
tons to enter the channel num ber you want to add or
delete.
Helpful Hint
TO ADJUST PRESS { /
B
CH23
• To review the channels memorized
by the TV/VCR, follow these steps.
1) Press the MENU button.
2) Press the PLAY/▲ button or the
STOP/▼ button to select
SAVED
>
CHANNEL
INPUT
EXIT
PRIM. SETUP
VCR PROGRAM
VCR SETUP
PRIM.SETUP. Press the
FF/SEARCH B button.
4
3) Press the PLAY/▲ button or the
STOP/▼ button to select CH MEM-
ORY REVIEW. Press the
FF/SEARCH B button. A list of pro-
grammed channels will appear on-
screen.
4) If all the programmed channels
don’t fit on-screen, press the
FF/SEARCH B button. If you do not
press the FF/SEARCH B button
within 10 seconds, the remaining
channels will appear on-screen. (If
there are no remaining channels,
the previous menu will appear.) Or
Press the FF/SEARCH B button or the
REW (ind)/SEARCH { button to select SAVED (to add
that channel) or DELETED (to delete that channel).
5
Press the STATUS/EXIT button.
Programming of the channel you added or deleted will appear.
press the REW(ind)/SEARCH
{
button to see the previous screen of
channels.
5) Press the STATUS/EXIT button
once or twice.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 12
12 Setting the Clock
There are three ways to set the clock: Manually, with Automatic
PBS Channel Selection, or with Manual PBS Channel Selection.
With manual clock setting, you tell the TV/VCR the current time.
With Automatic or Manual PBS Channel Selection, the TV/VCR
gets the time from your local PBS station. If you use either Manual
PBS Channel Selection or Automatic PBS Channel Selection, fol-
low the steps on page 19 to have the TV/VCR maintain the clock
according to your Time Zone.
To set the clock manually, follow the steps on pages 12 -13. To
set the clock using Automatic PBS Channel Selection, follow the
steps on pages 14 - 15. To set the clock using Manual PBS
Channel Selection, follow the steps on pages 16 - 17.
Before you begin, make sure:
● The TV/VCR is hooked up and turned on.
● Channels are set up.
● You make each entry within 60 seconds of the previous entry.
1
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
4
7
5
8
0
6
9
CHANNEL
ALT.CH
+100
SLEEP
SPEED
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
Manual Clock Setting
STOP/
PAUSE/STILL
1
Press the MENU button.
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
PRESS
B
REMINDER
BRIGHTNESS
2-3
2
Press the PLAY/▲ button or the STO P/▼ button to select
PRIM. SETUP. Then, press the FF/SEARCH B button.
PRIMARY SETUP
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME BAR
SET CLOCK
[ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
3
Helpful Hints
Press the PLAY/▲ button or the STO P/▼ button to select
SET CLO CK. Then, press the FF/SEARCH B button.
• Entries that do not match the
TV/VCR’s calendar will cause a
question mark (?) to appear on the
screen.
• To make corrections while you are
setting the clock, press the CLEAR
button until the space for the num-
ber you want to correct is flashing.
Then enter the correct number.
SET CLOCK
> AUTO CLOCK
SET MANUAL CLOCK
DAYLIGHT SVG.TIME
SET TIME ZONE
[AUTO]
[ON]
[ON]
TO CONTINUE PRESS MENU
SELECT KL CHOOSE
TO END PRESS EXIT
B
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 13
Setting the Clock (cont’d) 13
4
If O N appears beside AUTO CLO CK, press the
FF/SEARCH B button so that O FF appears to the right of
AUTO CLO CK, then press the MENU button. If O FF
appears beside AUTO CLO CK, press the MENU button.
SET MANUAL CLOCK
TIME – – : – –
7
POWER
MENU
STATUS/EXIT
CLEAR
DATE – – / – – / – –
4
1
2
3
MEMORY
4
7
5
8
0
6
9
TO END PRESS EXIT
CHANNEL
ALT.CH
+100
SLEEP
SPEED
5
VOLUME
MUTE
Press two Num ber buttons for the hour(s) and two
Num ber buttons for the m inute(s). Then press 1 for AM
or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
STOP/
PAUSE/STILL
SET MANUAL CLOCK
TIME
09 : 30 PM
MONTH
– – / – – / – –
TO CORRECT PRESS CLEAR
TO END PRESS EXIT
6
5-6
Press two Num ber buttons for the m onth, two Num ber
buttons for the day, and two Num ber buttons for the
year. For example, for July 1, 1998, press 07, 01, 98. The day of
the week will appear automatically.
SET MANUAL CLOCK
TIME
09 : 30 PM
DATE
07 / 01 / 98
WEDNESDAY
TO CORRECT PRESS CLEAR
TO END PRESS EXIT
7
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 14
14 Setting the Clock (cont’d)
Autom atic PBS Channel Selection
1
Press the MENU button.
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
PRESS
B
1
REMINDER
BRIGHTNESS
POWER
MENU
STATUS/EXIT
CLEAR
4
1
2
3
MEMORY
4
7
5
8
0
6
9
2
Press the PLAY/▲ button or the STO P/▼ button to select
PRIM. SETUP. Then, press the FF/SEARCH B button.
CHANNEL
ALT.CH
+100
PRIMARY SETUP
SLEEP
SPEED
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME
MUTE
VOLUME BAR
SET CLOCK
[ON]
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
STOP/
PAUSE/STILL
SELECT KL CHOOSE
B
TO END PRESS EXIT
3
Press the PLAY/▲ button or the STO P/▼ button to select
SET CLO CK. Then, press the FF/SEARCH B button.
SET CLOCK
> AUTO CLOCK
SET MANUAL CLOCK
DAYLIGHT SVG.TIME
SET TIME ZONE
[AUTO]
[ON]
[ON]
2-3
TO CONTINUE PRESS MENU
SELECT KL CHOOSE
TO END PRESS EXIT
B
4
If O N appears beside AUTO CLO CK, press the MENU
button. If O FF appears beside AUTO CLO CK, press the
FF/SEARCH B button so that O N appears to the right of
AUTO CLO CK, then press the MENU button.
AUTO CLOCK
AUTO CLOCK USES
PBS CHANNEL DATA
>
SET PBS CH. AUTO
SET PBS CH. MANUAL
SELECT KL CHOOSE
B
TO END PRESS EXIT
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 15
Setting the Clock (cont’d) 15
Wait for the TV/VCR to find
the time.
5
6
Press the PLAY/▲ button or the STO P/▼ button to
select SET PBS CH. AUTO . Then, press the
FF/SEARCH B button.
SET AUTO CLOCK
TIME
– – : – –
DATE
– – / – – / – –
NOW SEARCHING
TO END PRESS EXIT
7
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
4
7
5
8
0
6
9
CHANNEL
ALT.CH
6
NOW SEARCHING flashes on the TV/VCR screen.
+100
However, you may see the message: “PLEASE TURN OFF TO
SET AUTO CLOCK PLEASE WAIT SEVERAL MINUTES.” If this
message appears, turn off the TV/VCR for a few minutes. When
you turn on the TV/VCR, the time will be set. If the time is not
set, repeat steps 1 - 5. Or, follow the steps on pages 12 - 13 to
set the clock manually or pages 16 - 17 to set the clock with
Manual PBS Channel Selection.
SLEEP
SPEED
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
STOP/
PAUSE/STILL
5
7
W hen the TV/VCR finds the PBS channel, the tim e will
appear on-screen. Press the STATUS/EXIT button.
SET AUTO CLOCK
TIME
06 : 30 PM
DATE
07 / 01 / 98
WEDNESDAY
TO END PRESS EXIT
● If CANNO T FIND CLO CK DATA flashes on the
TV/VCR screen, you will be prom pted to turn off the
TV/VCR. Turn off the TV/VCR. Leave it off for several min-
utes. When you turn on the TV/VCR again, the clock will be
set.
Helpful Hints
• To display the time, press the STA-
TUS/EXIT button. A status display,
which includes the time, will appear
on the TV/VCR screen. Details are
on page 26.
SET AUTO CLOCK
TIME
– – : – –
DATE
– – / – – / – –
CANNOT FIND CLOCK DATA
TO END PRESS EXIT
• You must turn off the TV/VCR for
several minutes during automatic
clock setting. If the clock is not set
when you turn on the TV/VCR,
repeat the steps for Automatic PBS
Channel Selection. If the clock still is
not set, set the clock manually.
• You cannot use the AUTO CLOCK
feature if you don’t receive a PBS
channel that carries a time signal in
your area. Set the clock manually.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 16
16 Setting the Clock (cont’d)
Manual PBS Channel Selection
1
Press the MENU button.
1
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
PRESS
B
POWER
MENU
STATUS/EXIT
CLEAR
REMINDER
4
1
2
3
BRIGHTNESS
MEMORY
4
7
5
8
0
6
9
CHANNEL
ALT.CH
2
+100
Press the PLAY/▲ button or the STO P/▼ button to select
SLEEP
SPEED
PRIM. SETUP. Then, press the FF/SEARCH B button.
VOLUME
MUTE
PRIMARY SETUP
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
STOP/
PAUSE/STILL
VOLUME BAR
SET CLOCK
[ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
3
Press the PLAY/▲ button or the STO P/▼ button to select
SET CLO CK. Then, press the FF/SEARCH B button.
SET CLOCK
2-3
> AUTO CLOCK
SET MANUAL CLOCK
DAYLIGHT SVG.TIME
SET TIME ZONE
[AUTO]
[ON]
[ON]
TO CONTINUE PRESS MENU
SELECT KL CHOOSE
TO END PRESS EXIT
B
4
If O N appears beside AUTO CLO CK, press the MENU
button. If O FF appears beside AUTO CLO CK, press the
FF/SEARCH B button so that O N appears to the right of
AUTO CLO CK, then press the MENU button.
AUTO CLOCK
AUTO CLOCK USES
PBS CHANNEL DATA
>
SET PBS CH. AUTO
SET PBS CH. MANUAL
SELECT KL CHOOSE
B
TO END PRESS EXIT
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 17
Setting the Clock (cont’d) 17
5
Press the PLAY/▲ button or the STO P/▼ button to
select SET PBS CH. MANUAL. Then, press the
FF/SEARCH B button.
Wait for the TV/VCR to
find the time.
7
AUTO CLOCK (PBS) CH – –
TIME
– – : – –
DATE
– – / – – / – –
SELECT CHANNEL NUMBER
TO END PRESS EXIT
8
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
4
7
5
8
0
6
9
CHANNEL
ALT.CH
6
6
Use the Num ber buttons to select your PBS station. If you
make a mistake, press the CLEAR button, then enter the correct
number.
+100
SLEEP
SPEED
VOLUME
MUTE
AUTO CLOCK (PBS) CH 12
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
TIME
– – : – –
STOP/
PAUSE/STILL
DATE
– – / – – / – –
5
NOW SEARCHING
SELECT CHANNEL NUMBER
TO END PRESS EXIT
7
NOW SEARCHING flashes on the TV/VCR screen.
8
W hen the TV/VCR finds the clock data, the tim e will
appear on-screen. Press the STATUS/EXIT button.
AUTO CLOCK (PBS) CH 12
TIME
06 : 30 PM
DATE
07 / 01 / 98
WEDNESDAY
SELECT CHANNEL NUMBER
TO END PRESS EXIT
● If CANNO T FIND CLO CK DATA flashes on the
TV/VCR screen and you know another PBS channel,
press the PLAY/▲ button or the STO P/▼ button to
choose SELECT NEW PBS CH. Then, press the
FF/SEARCH B button. Repeat step 6.
● If CANNO T FIND CLO CK DATA flashes on the
TV/VCR screen and you do not know another channel,
press the PLAY/▲ button or the STO P/▼ button to
select SET PBS CH. AUTO. Then, press the
FF/SEARCH B button. The TV/VCR will search for the PBS
channel automatically.
Helpful Hints
• If you have an Antenna hookup, you
may select channels 2 - 69 at step
6. If you have a cable connection,
you may select channels 1 - 125 at
step 6. Details about available
memorized channels are on page
11.
• To display the time, press the STA-
TUS/EXIT button. A status display,
which includes the time, will appear
on the TV/VCR screen. Details are
on page 26.
• If the PBS channel is found, the time will appear on-screen.
• If the PBS channel is not found, you will be prompted to turn
off the TV/VCR. Leave it off for several minutes. When you turn
on the TV/VCR again, the time will be set.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 18
18 Daylight-Saving Time
When the Daylight-Saving Time feature is ON, the TV/VCR clock
will automatically move forward one hour on the first Sunday in
April and move back one hour on the last Sunday in October.
To turn Daylight-Saving Time ON or OFF, follow the steps below.
1
5
1
Press the MENU button.
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
4
7
5
8
0
6
9
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
PRESS
B
CHANNEL
ALT.CH
REMINDER
+100
BRIGHTNESS
SLEEP
SPEED
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
2
Press the PLAY/▲ button or the STO P/▼ button to select
PRIM. SETUP. Then, press the FF/SEARCH B button.
STOP/
PAUSE/STILL
PRIMARY SETUP
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME BAR
SET CLOCK
[ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
2-4
3
Press the PLAY/▲ button or the STO P/▼ button to select
SET CLO CK. Then, press the FF/SEARCH B button.
SET CLOCK
> AUTO CLOCK
SET MANUAL CLOCK
DAYLIGHT SVG.TIME
SET TIME ZONE
[AUTO]
[ON]
[ON]
TO CONTINUE PRESS MENU
SELECT KL CHOOSE
TO END PRESS EXIT
B
4
Press the PLAY/▲ button or the STO P/▼ button to select
DAYLIGHT SVG.TIME. Then, press the FF/SEARCH
button so that O N or O FF appears beside DAYLIGHT
SVG. TIME (Daylight Saving Tim e).
B
5
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 19
Time Zone 19
When you set the clock using AUTO CLOCK, specify a time zone in which a local PBS channel is located.
The TV/VCR will maintain the clock according to your time zone.
1
1,6
Press the MENU button.
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
PRESS
B
REMINDER
BRIGHTNESS
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
2
4
7
5
8
0
6
9
Press the PLAY/▲ button or the STO P/▼ button to select
PRIM. SETUP. Then, press the FF/SEARCH B button.
CHANNEL
ALT.CH
PRIMARY SETUP
+100
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
SLEEP
SPEED
VOLUME BAR
SET CLOCK
[ON]
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
SELECT KL CHOOSE
B
TO END PRESS EXIT
STOP/
PAUSE/STILL
3
Press the PLAY/▲ button or the STO P/▼ button to select
SET CLO CK. Then, press the FF/SEARCH B button.
SET CLOCK
> AUTO CLOCK
SET MANUAL CLOCK
DAYLIGHT SVG.TIME
SET TIME ZONE
[AUTO]
[ON]
[ON]
2-5
TO CONTINUE PRESS MENU
SELECT KL CHOOSE
TO END PRESS EXIT
B
4
Press the PLAY/▲ button or the STO P/▼ button to select
SET TIME ZO NE. Then, press the FF/SEARCH B button.
SET TIME ZONE
> AUTO
ATLANTIC
[ON]
EASTERN
CENTRAL
MOUNTAIN
PACIFIC
ALASKA
HAWAII
SELECT KL
TO CONTINUE PRESS MENU
Helpful Hints
5
• If you select AUTO at step 5, the
TV/VCR will set the clock according
to the time zone data of the PBS
station it finds.
Press the PLAY/▲ button or the STO P/▼ button to select
a tim e zone.
• You cannot select SET TIME ZONE
at step 4 if AUTO CLOCK is set to
OFF.
6
Press the MENU button, then press the STATUS/EXIT
button.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 20
20 Front Panel
Cassette Com partm ent
Insert a video cassette tape here.
W ireless Rem ote Sensor
Receives a signal from your remote control
so you can operate the TV/VCR from a dis-
tance.
STO P/EJECT Button
Press once to stop the tape. When playback
is stopped, press to eject the tape. Press to
select an item in the pop up menu.
VIDEO Jack
Connect this jack to the video out jack of a
camcorder or a VCR. Details are on page 31.
AUDIO Jack
Connect this jack to the audio out jack of a
camcorder or a VCR. Details are on page 31.
EARPHO NE Jack
AUDIO
VIDEO
STOP/EJECT
REW
PLAY
F.FWD
REC/OTR
CHANNEL
VOLUME
POWER
EARPHONE
Connect earphones (not supplied) here for
personal listening.
REW (ind) Button
VO LUME o/p
Buttons
Press to adjust the
sound level.
Press the CHANNEL
o button and the
VOLUME p button
on the TV/VCR at
the sam e tim e to
display the pop up
menu. Press again to
remove the menu.
When tape playback is stopped, press to
rewind the tape at high speed. During play-
back, press to rewind the tape while the pic-
ture stays on-screen. Press to change a set-
ting of a pop up menu item (for example, to
adjust the BRIGHTNESS setting).
PLAY Button
Press to play a tape. Details are on page 28.
Press to release Search or Still mode and
return to normal playback. Details are on page
46. Press to select an item in the pop up
menu.
F.FW D Button
CHANNEL o/p
Buttons
When tape playback is stopped, press to fast
forward the tape at high speed. During play-
back, press to fast forward the tape while the
picture stays on-screen. Press to change a
setting of a pop up menu item (for example,
to adjust the BRIGHTNESS setting).
Press to scan through
the TV/VCR channels.
During tape playback,
press to adjust the
tracking. Details are
on page 45.
REC(ord)/O TR Button
Press once to start a recording. Details are on
page 29. Press repeatedly to start a One-
Touch Recording (an immediate timed
recording, 30 minutes to eight hours long) of
the channel you are watching. Details are on
page 30.
Press the CHANNEL
o button and the
VOLUME p button
on the TV/VCR at
the sam e tim e to
display the pop up
menu. Press again to
remove the menu.
RECO RD Light
Appears during a recording. It flashes when
the TV/VCR power is turned off to set a
timer recording or when a recording is
paused.
PO W ER Button
Press to turn the power on or off.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 21
Rear Panel 21
ANT.
ANT(enna) Jack
Connect your antenna or cable here.
AC Power Cord
Details are on pages six - seven.
Connect to a standard AC outlet to
supply power to the TV/VCR.
Antenna Hole
Connect the stem of an indoor antenna
here. Details are on page six.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 22
22 Remote Control Buttons
CLEAR Button
Press to erase incorrect data when programming TV/VCR func-
tions. Also, press to reset the real-time counter to 0:00:00.
Details are on page 44.
PO W ER Button
Press to turn on or off the TV/VCR.
Num ber Buttons
Use to select channels and to program TV/VCR functions (such as
setting the clock).
● Channels 1 - 9
To select, press 0, then press the channel you want. For example,
to select channel 7, press 0, 7.
POWER
MENU
STATUS/EXIT
CLEAR
● Channels 100 and above
1
2
3
MEMORY
To select, press the +100 button, then press the last two digits of
the channel you want. For example, to select channel 117, press
the +100 button, 1, 7.
4
7
5
8
0
6
9
CHANNEL
ALT.CH
VO LUME o/p Buttons
Press to adjust the sound level. If you press the VOLUME o/p
buttons when the sound is muted, the sound will be restored.
+100
SLEEP
SPEED
REW (ind)/SEARCH { Button
When tape playback is stopped, press to rewind the tape at high
speed. During tape playback, press to rewind the tape while the
picture stays on-screen. Details are on page 46.
Press to change a setting of a pop up menu item or to return to a
previous menu screen. Press to adjust the picture controls. Details
are on pages 24 - 25.
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
STOP/
PAUSE/STILL
REC(ord)/O TR Button
Press once to start a recording. Details are on page 29. Or, press
repeatedly to start a One-Touch Recording (an immediate timed
recording, 30 minutes to eight hours long) of the channel you are
watching. Details are on page 30.
STO P/▼ Button
Press to stop the tape. Press to select an item in the on-screen
menu.
PAUSE/STILL Button
During recording, press to temporarily stop the recording. Press
again to resume recording. Details are on page 29. You cannot
pause a One-Touch Recording.
During tape playback, press to freeze the picture (still). Each time
you press the PAUSE/STILL button, the noise lines will change
position on-screen. Details are on page 46.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 23
Remote Control Buttons (cont’d) 23
STATUS/EXIT Button
Press to see the status display. Press again to remove the status
display. Details are on page 26. Press to exit the on-screen menu.
MENU Button
Press to display the pop up menu. You may also use the buttons
on the front panel of the TV/VCR to access the pop up menu.
Details are on page 20.
MEMO RY Button
Press to memorize a tape position at which the real-time counter
was set to 0:00:00. Details are on page 44. Or, press to memorize
the start and end position on a tape when setting up A-B Repeat
Play. Details are on pages 42 - 43.
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
CHANNEL o/p Buttons
Press to scan through the TV/VCR’s channels.
4
7
5
8
0
6
9
ALT. CH (Alternate Channel) Button
Press to return to the TV channel you were viewing immediately
before switching to your current channel.
CHANNEL
ALT.CH
+100
SLEEP Button
Press to set the sleep timer. Details are on page 37.
SLEEP
SPEED
MUTE Button
VOLUME
MUTE
Press to eliminate the TV/VCR’s sound. Press again to return to
the previous volume level.
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
PLAY/▲ Button
STOP/
PAUSE/STILL
Press to play a tape. Details are on page 28. Press to release Search
or Still mode and return to normal playback. Details are on page
46. Press to select an item in the on-screen menu.
FF/SEARCH B Button
When tape playback is stopped, press to fast forward the tape at
high speed. During tape playback, press to fast forward the tape
while the picture stays on-screen. Details are on page 46.
Press to change the setting of an item in the on-screen menu or
press to proceed to the next menu. Press to adjust the picture
controls. Details are on pages 24 - 25.
SPEED Button
Press to select the recording speed (SP, LP, or SLP).
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 24
24 Adjusting the Picture Controls
Follow these steps to adjust the TV/VCR’s brightness, picture,
color, tint, and sharpness.
1
Press the MENU button.
TO ADJUST PRESS { /
B
>
BRIGHTNESS
PICTURE
COLOR
1
3
POWER
MENU
STATUS/EXIT
CLEAR
4
2
TINT
SHARPNESS
TV RESET
1
2
3
MEMORY
4
7
5
8
0
6
9
CHANNEL
ALT.CH
2
+100
Press the PLAY/▲ button or the STO P/▼ button to select
the desired control (BRIGHTNESS, for exam ple).
SLEEP
SPEED
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
3
STOP/
PAUSE/STILL
Press the REW (ind)/SEARCH { button or the
FF/SEARCH B button to adjust the picture control. (Refer
to the chart on page 25.)
4
W hen you finish, press the STATUS/EXIT button.
Helpful Hints
• The on-screen menus shown on
page 25 will disappear if no adjust-
ments are made within 60 seconds.
• The original settings will probably
give you the best picture quality.
• To reset the picture controls to the
original settings, press the MENU
button, then press the PLAY/▲ but-
ton or the STOP/▼ button to select
TV RESET, then press the
FF/SEARCH B button. TV RESET
COMPLETED will appear on-screen
briefly.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 25
Adjusting the Picture Controls (cont’d) 25
Decrease
decreased brightness
decreased contrast
paler
Increase
increased brightness
increased contrast
more brilliant
more green
BRIGHTNESS
PICTURE
CO LO R
TINT
SHARPNESS
more purple
softer
clearer
Press the
REW(ind)/SEARCH
{
button to decrease a
picture control. Press
the FF/SEARCH
B
button to increase a
picture control.
AUDIO
VIDEO
STOP/EJECT
REW
PLA
CHANNEL
VOLUME
POWER
EARPHONE
TO ADJUST PRESS { /
B
TO ADJUST PRESS { /
B
TO ADJUST PRESS { /
B
BRIGHTNESS
BRIGHTNESS
PICTURE
COLOR
TINT
SHARPNESS
TV RESET
>
BRIGHTNESS
PICTURE
COLOR
>
PICTURE
COLOR
TINT
SHARPNESS
TV RESET
>
TINT
SHARPNESS
TV RESET
TO ADJUST PRESS{ /
B
TO ADJUST PRESS { /
B
BRIGHTNESS
PICTURE
COLOR
TINT
SHARPNESS
TV RESET
BRIGHTNESS
PICTURE
COLOR
TINT
SHARPNESS
TV RESET
>
>
Press the STOP/▼
Button
Press the PLAY/▲
Button
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 26
26 On-Screen Status Displays
A status display will appear when you press the STATUS/EXIT
button or certain function buttons. The contents of the status dis-
play will vary. To choose the status display mode, follow the steps
below.
If you select STATUS O N, then select CO UNTER O NLY
O FF:
● Whenever you press the STOP/p button or the PLAY/o but-
ton, the status display will appear for five seconds.
If you select STATUS O N, then select CO UNTER O NLY
O N:
● Whenever you press the PLAY/o button, the status display will
appear for five seconds. After five seconds, only the counter will
remain on-screen.
Function
Button
Channel
Time
Pressed
12:00 AM
CH10
STOP
If you select STATUS O FF:
SLP
M 1:23:45
● The status display will not appear when you press function but-
tons. You must press the STATUS/EXIT button to see the sta-
tus display.
Counter
and
Tape
Speed
Counter
Memory
1
Press the MENU button.
2
Press the PLAY/▲ button or the STO P/▼ button to select
VCR SETUP, then press the FF/SEARCH B button.
3
Press the PLAY/▲ button or the STO P/▼ button to select
O N-SCREEN MO DE, then press the FF/SEARCH B but-
ton.
4
Press the PLAY/o button or the STO P/p button to select
STATUS, then press the FF/SEARCH B button so that
O N or O FF appears beside STATUS.
ON-SCREEN MODE
> STATUS
[ON]
[OFF]
COUNTER ONLY
SELECT KL CHOOSE
B
TO END PRESS EXIT
5
Helpful Hints
If you set STATUS to O FF, go to step 6. If you set STA-
TUS to O N, press the PLAY/o button or the STO P/p
button to select CO UNTER O NLY, then press the
FF/SEARCH B button so that O N or O FF appears beside
it.
• If the channel you select has no
broadcast, the screen will be solid
blue.
• You cannot view closed captions
during recording or tape playback if
COUNTER ONLY is set to ON.
Details are on pages 38 - 39.
6
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 27
Reminder 27
The channel number will remain on-screen at all times when you
set REMINDER to ON in the pop up menu. The exception is dur-
ing tape playback, Forward and Reverse Searching and Still modes,
and when closed captioning is selected (CAPTION in the pop up
menu).
Set REMINDER to ON or OFF by following the steps below.
1
1
3
POWER
MENU
STATUS/EXIT
CLEAR
4
2
Press the MENU button.
1
2
3
MEMORY
TO ADJUST PRESS { /
B
4
7
5
8
0
6
9
OFF
>
REMINDER
BRIGHTNESS
PICTURE
COLOR
CHANNEL
ALT.CH
+100
TINT
SHARPNESS
SLEEP
SPEED
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
2
STOP/
PAUSE/STILL
Press the PLAY/▲ button or the STO P/▼ button to select
REMINDER.
TO ADJUST PRESS { /
B
OFF
>
REMINDER
BRIGHTNESS
PICTURE
COLOR
TINT
SHARPNESS
3
Press the REW (ind)/SEARCH { button or the
FF/SEARCH B button to select O N or O FF. Each press of
the REW(ind)/SEARCH { button or the FF/SEARCH B button
turns REMINDER ON or OFF.
TO ADJUST PRESS { /
B
CH12
ON
REMINDER
BRIGHTNESS
PICTURE
COLOR
TINT
SHARPNESS
4
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 28
28 Playing
Follow the steps below to play a tape.
Insert a tape in the TV/VCR.
1
5
1
Press the STOP/EJECT button
on the TV/VCR.
Insert a tape in the TV/VCR. The power will come on. If the
tape’s record tab has been removed, playback should start auto-
matically.
2
If playback does not start autom atically, press the
PLAY/▲ button to start playback.
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
4
7
5
8
0
6
9
CHANNEL
ALT.CH
3
+100
Press the STO P/▼ button on the rem ote control or the
STO P/EJECT button on the TV/VCR once to stop play-
back.
SLEEP
SPEED
VOLUME
MUTE
2
3
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
4
4
STOP/
PAUSE/STILL
Press the REW (ind)/SEARCH { button to rewind the
tape.
5
W hen the tape has finished rewinding, press the
STO P/EJECT button on the TV/VCR to rem ove the tape.
Helpful Hints
• If the tape you want to play is
already in the TV/VCR, turn on the
TV/VCR power, then press the
PLAY/▲ button.
• Playback features and options are
on pages 41 - 46.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 29
Recording 29
Read and follow the steps below to record a TV program.
1
Place a tape with its record tab intact (see page five) in
the TV/VCR. The power will come on. O r, if the tape is
already in the TV/VCR, press the PO W ER button.
2
Press the SPEED button until the desired tape speed
appears on the TV/VCR screen. Details about tape speed are
given below.
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
1
4
7
5
8
0
6
9
CHANNEL
ALT.CH
3
3
Use the CHANNEL o/p buttons or the Num ber buttons
to select the channel to be recorded. (Channels cannot be
changed during recording.)
+100
SLEEP
SPEED
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
2
5
6
4
4
STOP/
PAUSE/STILL
Press the REC(ord)/O TR button once to start recording.
The RECORD light will glow.
● If there is not a tape in the TV/VCR, NO CASSETTE flashes on-
screen briefly.
● If the tape does not have a record tab, PROTECTED CAS-
SETTE CANNOT RECORD flashes on-screen briefly. The
TV/VCR will eject the tape. Insert another tape.
5
To pause the recording (for exam ple, during com m er-
cials), press the PAUSE/STILL button. The RECORD light
will flash. To resum e recording, press the PAUSE/STILL
button again or the REC(ord)/O TR button. The RECORD
light will glow.
Helpful Hints
6
• You cannot record one channel
while watching another.
• Recording options are on pages 30
- 36.
• You cannot record if RECORD
DEFEAT is set to ON. (REC
DEFEATED will flash on-screen.)
Details are on page 36.
• If you pause a recording for more
than five minutes, the TV/VCR will
switch to Stop mode automatically
to protect the video cassette tape
from damage.
To stop recording, press the STO P/▼ button.
Tape Speeds
This chart shows the recording/playback time for three types of
video cassettes (T160, T120, and T60). There are three playback
speeds: SP, LP, and SLP. During playback, the VCR selects the
tape speed automatically. When recording, you can change the
tape speed using the SPEED button (see page 23).
Tape Speed
Type
SP
(Standard Play)
LP
(Long Play)
SLP
Maximum Record/Playback Time
T160
2 hrs.
40 mins.
5 hrs.
T120
T60
2 hrs.
1 hr.
• You can change the tape speed
with the SPEED button while a
recording is in progress, but some
distortion may appear on the tape.
4 hrs.
6 hrs.
2 hrs.
3 hrs.
20 mins.
8 hrs.
(Super Long Play)
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 30
30 One-Touch Recording
The One-Touch Recording (OTR) function allows you to program
an immediate timed recording from 30 minutes to eight hours
long without setting the timer.
Before you begin, make sure:
● Channels are set up.
Press the STOP/EJECT but-
ton on the TV/VCR to stop
the OTR.
4
3
● There is a tape in the TV/VCR. The record tab must be intact.
1
Use the CHANNEL o/p buttons or the Num ber buttons
to select the channel you want to record.
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
4
7
5
8
0
6
9
2
CHANNEL
ALT.CH
Press the SPEED button until the desired recording speed
(SP, LP, or SLP) appears on-screen. Details are on page 29.
1
2
+100
SLEEP
SPEED
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
3
STOP/
PAUSE/STILL
Press the REC(ord)/O TR button repeatedly until the
desired recording length appears in the upper right corner of the
screen. Recording will begin immediately. The RECORD light will
appear.
OTR
LENGTH 0:30
CH12
LENGTH
CANCEL
:
:
PRESS OTR
PRESS CLEAR
Helpful Hints
4
To stop an O TR before recording is finished, press the
STO P/EJECT button on the TV/VCR.
O r, press the REC(ord)/O TR button, then press the
CLEAR button, then press the STO P/▼ button on the
rem ote control.
• To check the time remaining for an
OTR after the OTR has been set,
press the STATUS/EXIT button.
• To change the recording length
while an OTR is in progress, press
the REC(ord)/OTR button until the
desired recording length appears
on-screen.
• You can not pause an OTR.
• To cancel an OTR but continue
recording, press the REC(ord)/OTR
button, then press the CLEAR but-
ton.
• You cannot record if RECORD
DEFEAT is set to ON. Details are
on page 36.
• You can change the tape speed
with the SPEED button while a
recording is in progress, but some
distortion may appear on the tape.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 31
Rerecording (Tape Duplication) 31
AUDIO and VIDEO OUT Jacks on source unit
(VCR or Camcorder)
AUDIO
VIDEO
STOP/EJECT
EARPHONE
VIDEO AUDIO
OUT
IN
Audio Cable (white) from
AUDIO OUT to AUDIO
AUDIO and VIDEO
Jacks on TV/VCR
Video Cable (yellow) from
VIDEO OUT to VIDEO
1
Make the connections shown above, using audio and video
cables. (Make sure the source unit is connected to a
power source.)
2
The source unit (VCR or camcorder) will play your tape. Insert a
prerecorded tape in the source unit. If playback begins, press
the STOP button on the unit.
3
The TV/VCR will record your tape. Insert a blank tape in the
TV/VCR. Make sure the tape’s record tab is intact. The TV/VCR
power will turn on automatically.
4
Point the TV/VCR rem ote control at the TV/VCR. Press
Num ber buttons 0, 0 so that A/V IN appears on-screen.
5
Point the TV/VCR rem ote control at the TV/VCR. Press
the SPEED button until the desired tape speed (SP, LP,
or SLP) appears on-screen.
Helpful Hints
• Unauthorized recording of copy-
righted television programs, video
tapes, or other materials may
infringe on the rights of copyright
owners and violate copyright laws.
• Different brands of equipment may
operate differently.
6
Press the PLAY button on the source unit and the
REC(ord)/O TR button on your TV/VCR at the sam e tim e.
Copying will begin.
• Make sure all connections are
secure. Otherwise, you may not
record both picture and sound.
• Audio and video cables are not
included.
7
To stop copying, press the STO P/EJECT button on the
TV/VCR, then stop the tape on the source unit (VCR or
cam corder).
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 32
32 Timer Recording
Follow the steps below to program the TV/VCR to record TV
programs while you’re away from home. The TV/VCR will turn
itself on, record, and turn itself off automatically. Before you begin,
make sure:
● The clock is set. If not, CLOCK MUST BE SET appears.
● Channels are set up.
● There is a tape in the TV/VCR. (Make sure the tape’s record
tab is intact and the tape is long enough to record the pro-
gram.)
1
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
4
7
5
8
0
6
9
CHANNEL
ALT.CH
Com plete each step within 60 seconds of com pleting the
previous step. If you don’t, you m ay start again at step 1.
+100
SLEEP
SPEED
VOLUME
MUTE
1
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
Press the MENU button.
STOP/
PAUSE/STILL
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
REMINDER
BRIGHTNESS
2
Press the PLAY/▲ button or the STO P/▼ button to select
VCR PRO GRAM, then press the FF/SEARCH B button.
2-3
VCR PROGRAM
> ONCE
DAILY(MON-FRI)
WEEKLY
PROGRAM REVIEW
SELECT KL CHOOSE
B
TO END PRESS EXIT
3
Helpful Hints
Press the PLAY/▲ button or the STO P/▼ button to select
a O NCE, DAILY, O R W EEKLY recording. Then, press
the FF/SEARCH B button.
• If the power fails, programmed
timer recordings will be restored
when the clock is reset. (The clock
will reset itself automatically if you
are using the AUTO CLOCK feature.
Details are on pages 14 - 17. If
you are not using the AUTO CLOCK
feature, reset the clock manually.
Details are on pages 12 - 13.) The
timer recording will not occur only if
the timer recording was scheduled
to take place during the power fail-
ure.
● O NCE: The TV/VCR will record a TV program on any day you
choose, up to 12 months away.
● DAILY: The TV/VCR will record every day from Monday to
Friday – starting at the same time and recording the same channel
for the same length of time.
● W EEKLY: The TV/VCR will record the same channel on the
same day, at the same time, and for the same length of time
every week.
DAILY PROGRAM (MON-FRI)
PROGRAM -1 2 3 4 5 6 7 8-
Daily
Recording
(exam ple)
• You cannot set a timer recording if
RECORD DEFEAT is set to ON.
Details are on page 36.
SELECT PROGRAM NUMBER
TO END PRESS EXIT
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 33
Timer Recording (cont’d) 33
4
Use the Num ber buttons (1 - 8) to select a position in
which to store the tim er recording. Flashing numbers indi-
cate an open position (one in which a timer recording has not yet
been stored).
4-7
NOTE: If you select a number that has already been used to store a
timer recording, PREVIOUSLY SET PROGRAM will appear on-screen for
a few seconds. Then information about the program in that position
will appear on-screen. If this happens, press the STATUS/EXIT button.
Then use the Number buttons to select another position.
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
4
7
5
8
0
6
9
5
CHANNEL
ALT.CH
● Enter the channel of the TV program you want to record (you
must enter a 0 before all single-digit channels).
● If you are recording from line input, press 0, 0. A/V IN will
appear on-screen.
+100
SLEEP
SPEED
VOLUME
MUTE
● If you are recording using a Cable Box, enter the Cable Box
output channel (03 or 04). Be sure to select the channel of the
TV program at the Cable Box and leave the Cable Box on for
the timer recording.
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
STOP/
PAUSE/STILL
ONE TIME PROGRAM
PROGRAM
1
CHANNEL – –
TO CORRECT PRESS CLEAR
TO END PRESS EXIT
6
Press two Num ber buttons for the hour(s) you want the
recording to begin. Press two Num ber buttons for the
m inute(s) you want the recording to begin. Press 1 for
AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.
ONE TIME PROGRAM
PROGRAM
1
CHANNEL 10
TIME ON
– – : – –
TO CORRECT PRESS CLEAR
TO END PRESS EXIT
Helpful Hints
7
• If the numbers entered do not
match the TV/VCR’s calendar, the
entry will be rejected and a question
mark will appear on-screen.
Follow the instructions in step 6 to set the recording’s
stop tim e. (AM or PM will be set automatically.)
ONE TIME PROGRAM
PROGRAM
1
• To make corrections while you are
programming a timer recording,
press the CLEAR button until the
cursor is flashing on the item you
want to change. Then enter the cor-
rect information.
CHANNEL 10
TIME ON
09:30 PM
TIME OFF – – : – –
TO CORRECT PRESS CLEAR
TO END PRESS EXIT
Instructions continue on page 34.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 34
34 Timer Recording (cont’d)
8
11
8
10
9
Press the Num ber 1 button to record in SP speed, press
the Num ber 2 button to record in LP speed, or press the
Num ber 3 button to record in SLP speed. Details about tape
speed are on page 29. You cannot use the SPEED button at this
time.
ONE TIME PROGRAM
POWER
MENU
STATUS/EXIT
CLEAR
PROGRAM
1
1
2
3
MEMORY
CHANNEL 10
TIME ON
TIME OFF 11:00 PM
REC SPEED SLP
SP=1 LP=2 SLP=3
4
7
5
8
0
6
9
09:30 PM
CHANNEL
ALT.CH
+100
TO CORRECT PRESS CLEAR
TO END PRESS EXIT
SLEEP
SPEED
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
9
STOP/
PAUSE/STILL
Press two Num ber buttons for the m onth and two
Num ber buttons for the day you want the program to
record. For example, for July 10, 1998, press 07, 10. The day of
the week and the year will be displayed automatically. (You cannot
program the TV/VCR to record more than one year in advance.)
ONE TIME PROGRAM
PROGRAM
1
CHANNEL
TIME ON
TIME OFF
REC SPEED
10
09:30 PM
11:00 PM
SLP
START DATE 07/10/98
FRIDAY
TO CORRECT PRESS CLEAR
TO END PRESS EXIT
The TV/VCR m ust be
off for a tim er record-
ing! Make sure there is
a tape in the TV/VCR.
10
Press the STATUS/EXIT button. PROGRAM WAS COM-
PLETED PLEASE TURN OFF FOR TIMER RECORDING will
appear on-screen.
● If there is not a tape in the TV/VCR, PLEASE INSERT CAS-
SETTE also appears on-screen.
● If there is a tape without a record tab in the TV/VCR, PLEASE
REMOVE CASSETTE also appears on-screen. If this happens,
insert a different tape.
Helpful Hints
• PROGRAM NOT COMPLETED /
CLASH may appear on-screen when
you finish setting a timer recording.
This means that the timer recording
you just programmed and another
timer recording overlap, and thus
the current timer recording will not
be carried out.
● If PROGRAM NOT COMPLETED appears, start again at step 1.
11
Turn off the TV/VCR power. The RECORD light will flash. If
you forget to turn off the TV/VCR, PLEASE TURN OFF FOR
TIMER RECORDING appears on the TV/VCR screen two minutes
before a timer recording starts.
• To stop a started timer recording,
press the STOP/EJECT button on
the TV/VCR.
Please see page 48 for more
Helpful Hints.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 35
Timer Recording (cont’d) 35
Checking or Clearing Tim er Recordings
1
W ith the TV/VCR on, press the MENU button.
2
5
4
1
POWER
MENU
STATUS/EXIT
CLEAR
Press the PLAY/▲ button or the STO P/▼ button to select
VCR PRO GRAM, then press the FF/SEARCH B button.
1
2
3
MEMORY
4
7
5
8
0
6
9
CHANNEL
ALT.CH
3
Press the PLAY/▲ button or the STO P/▼ to select PRO -
GRAM REVIEW , then press the FF/SEARCH B button.
The timer recording information for the program in the lowest
numbered position will appear on-screen. If no timer recordings
are programmed, nothing will happen when you select PROGRAM
REVIEW.
+100
SLEEP
SPEED
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
STOP/
PAUSE/STILL
4
Press the FF/SEARCH B button to display inform ation
about the next program m ed tim er recording. (If you do
not press a button within 10 seconds, information about the next
programmed timer recording will appear.) This will continue until
all positions have been displayed. Then, the menu will disappear.
You can exit the Program Review at any time by pressing the
STATUS/EXIT button.
2-3
5
To cancel the tim er recording displayed, press the
CLEAR button. Either the display will disappear or information
about other timer recordings will appear. If you do not press any
other buttons, the display will disappear after all timer recordings
have been displayed.
6
Repeat steps 1 - 4 to m ake sure you have cleared the
correct position.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 36
36 Defeat Recording
Follow the steps below to prevent accidental recording.
1
Press the MENU button.
4
1
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
REMINDER
4
7
5
8
0
6
9
BRIGHTNESS
CHANNEL
ALT.CH
+100
2
SLEEP
SPEED
Press the PLAY/▲ button or the STO P/▼ button to select
VCR SETUP, then press the FF/SEARCH B button.
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
VCR SETUP
STOP/
PAUSE/STILL
> ONE TIME PLAY
REPEAT PLAY
ON-SCREEN MODE
RECORD DEFEAT
[ON]
[OFF]
SELECT KL CHOOSE
B
TO END PRESS EXIT
3
Press the PLAY/▲ button or the STO P/▼ button to select
RECO RD DEFEAT, then press the FF/SEARCH B button
so that O N appears beside RECO RD DEFEAT.
2-3
4
Press the STATUS/EXIT button.
5
Now, REC DEFEATED will flash on-screen when you
press the REC(ord)/O TR button.
Helpful Hints
REC DEFEATED
• If you set RECORD DEFEAT to ON
after a timer recording has been
set, the timer recording will not
occur.
• You can not program a timer
recording if RECORD DEFEAT is set
to ON.
• To set RECORD DEFEAT to OFF,
repeat steps 1 - 2 above. At step 3,
press the PLAY/o button or the
STOP/p button to select RECORD
DEFEAT, then press the FF/SEARCH
B button so that OFF appears
beside RECORD DEFEAT on-screen.
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 37
Setting the Sleep Timer 37
Use the sleep timer to program the TV/VCR to shut off in a cer-
tain amount of time.
1
1-2
Press the SLEEP button. The sleep timer display will appear
on-screen. (You can not set the sleep timer during a recording.)
POWER
MENU
STATUS/EXIT
CLEAR
SLEEP
0
MIN
1
2
3
MEMORY
4
7
5
8
0
6
9
CHANNEL
ALT.CH
2
W ithin five seconds, press the SLEEP button repeatedly
to select 30 m inutes, 60 m inutes, 90 m inutes, or 120 m in-
utes. In a few seconds, the display will disappear. Then the
TV/VCR will shut itself off after the specified amount of time.
One minute before the TV/VCR shuts itself off, the seconds will
count down on-screen.
+100
SLEEP
SPEED
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
STOP/
PAUSE/STILL
GOOD NIGHT appears on the TV/VCR screen 10 seconds
before the TV/VCR shuts itself off.
SLEEP 10 SEC
GOOD NIGHT
● To see how much time remains until the TV/VCR shuts itself
off, press the SLEEP button once. The time remaining will
appear on-screen briefly. You cannot do this during a recording.
● To cancel a sleep timer setting, press the SLEEP button until 0
MIN appears on-screen. The on-screen display will disappear in
a few seconds. You cannot cancel the sleep timer during a
recording.
Helpful Hints
• Finish all recordings before the
TV/VCR shuts itself off. If a record-
ing is in progress, the sleep timer
will be cancelled.
• A timer recording will not begin
unless the TV/VCR power is off.
Two minutes before a timer record-
ing starts, PLEASE TURN OFF FOR
TIMER RECORDING flashes on-
screen. If you see this message, turn
off the TV/VCR.
• If the power fails, you might lose
the sleep timer setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 38
38 Closed Caption
When you watch a program that is being broadcast with closed
captions, you can access on-screen boxes containing the pro-
gram’s dialogue (for example, what a character is saying), dialogue
in a foreign language, or information (such as a channel guide,
schedule, or announcements). Follow the steps below to select
closed captions.
Not all TV programs and commercials are broadcast with closed
captions. Similarly, all types of closed captions (second language,
half-screen text, etc.) are not always broadcast. If closed caption-
ing is not broadcast, you cannot receive it. This does not indicate
a problem with the TV/VCR. Refer to your area’s TV program
listings for the shows offered with closed captions.
1
3
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
4
7
5
8
0
6
9
CHANNEL
ALT.CH
+100
1
Press the MENU button.
SLEEP
SPEED
VOLUME
MUTE
PRESS
B
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
STOP/
PAUSE/STILL
REMINDER
BRIGHTNESS
2
2
Press the PLAY/▲ button or the STO P/▼ button to select
CAPTIO N.
TO ADJUST PRESS { /
B
OFF
>
CAPTION
REMINDER
BRIGHTNESS
PICTURE
COLOR
TINT
3
Press the REW (ind)/SEARCH { button or the
FF/SEARCH B button to select your desired m ode.
The selected closed caption mode will appear beside CAPTION
on-screen.
● CAPTION1 displays standard closed captions (what a character
is saying).
● CAPTION2 displays foreign language closed captions (foreign
language words showing what a character is saying).
● TEXT1 and TEXT2 display half-screen text (such as a channel
guide, schedule, or announcement).
● OFF turns closed captions off. Captions will not appear on-
screen.
TO ADJUST PRESS { /
B
Exam ple:
CAPTIO N1
Menu
CAPTION1
>
CAPTION
REMINDER
BRIGHTNESS
PICTURE
COLOR
Screen
TINT
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 39
Closed Caption (cont’d) 39
4
Press the STATUS/EXIT button. The type of closed captions
you selected at step 3 will appear on-screen.
4
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
4
7
5
8
0
6
9
CHANNEL
ALT.CH
HELLO
+100
Standard Closed Captions
SLEEP
SPEED
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
STOP/
PAUSE/STILL
WORLD WEEATHER
5 C
8 C
7 C
23:00
20:00
4:00
CLOUD
RAIN
CLOUD
NYL
LOS
LONDON
Half-screen text
Helpful Hints
• You cannot view closed captions
during recording or tape playback if
COUNTER ONLY is set to ON.
• Abbreviations, symbols, and other
grammatical shortcuts are often
used in order to keep pace with the
on-screen action. This does not indi-
cate a problem with the TV/VCR.
• To cancel closed captions, follow
steps 1 - 2 on page 38. At step 3,
press the REW(ind)/SEARCH
{
button or the FF/SEARCH B button
to select OFF. Press the
STATUS/EXIT button.
• When you change channels, the
closed captions may be delayed for
a few seconds.
• When you adjust the volume or
mute the volume, closed captions
may be delayed for a few seconds.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 40
40 Volume Bar
Usually, the volume bar appears when you press the VOLUME
o/p buttons. If you do not need it, set the VOLUME BAR to
OFF position. For example, when you watch a program that is
being broadcast with closed captions, you may choose to set the
VOLUME BAR to OFF so the captions can remain on-screen. The
captions will remain on-screen even when you press the VOLUME
o/p buttons or the MUTE button.
4
1
1
POWER
MENU
STATUS/EXIT
CLEAR
Press the MENU button.
1
2
3
MEMORY
4
7
5
8
0
6
9
CHANNEL
ALT.CH
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
+100
REMINDER
SLEEP
SPEED
BRIGHTNESS
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
2
STOP/
PAUSE/STILL
Press the PLAY/▲ button or the STO P/▼ button to select
PRIM. SETUP. Then, press the FF/SEARCH B button.
PRIMARY SETUP
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME BAR
SET CLOCK
[ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
2-3
3
Press the PLAY/▲ button or the STO P/▼ button to select
VO LUME BAR, then press the FF/SEARCH B button.
Each press of the FF/SEARCH B button will turn the VOLUME
BAR ON or OFF.
4
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 41
Repeat Play 41
Follow the steps below to program the TV/VCR to play a tape
over and over.
1
Press the MENU button.
4
1
POWER
MENU
STATUS/EXIT
CLEAR
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
1
2
3
MEMORY
4
7
5
8
0
6
9
REMINDER
BRIGHTNESS
CHANNEL
ALT.CH
+100
SLEEP
SPEED
2
VOLUME
MUTE
Press the PLAY/▲ button or the STO P/▼ button to select
VCR SETUP, then press the FF/SEARCH B button.
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
STOP/
PAUSE/STILL
VCR SETUP
> ONE TIME PLAY
REPEAT PLAY
ON-SCREEN MODE
RECORD DEFEAT
[ON]
[OFF]
SELECT KL CHOOSE
B
TO END PRESS EXIT
3
2-3
Press the PLAY/▲ button or the STO P/▼ button to select
REPEAT PLAY, then press the FF/SEARCH B button so
that O N appears beside REPEAT PLAY.
VCR SETUP
ONE TIME PLAY
> REPEAT PLAY
ON-SCREEN MODE
RECORD DEFEAT
[ON]
[OFF]
SELECT KL CHOOSE
B
TO END PRESS EXIT
Helpful Hints
4
Press the STATUS/EXIT button. Now, when a tape has fin-
ished playing, the TV/VCR will rewind it and start playback again.
(TV programming will appear while the tape is rewinding.)
• The TV/VCR will stay in Repeat Play
mode until you set ONE TIME PLAY
to ON, even if the TV/VCR is turned
off. To set ONE TIME PLAY to ON,
follow steps 1 - 2 above. Then,
press the PLAY/o button or the
STOP/p button to select ONE
TIME PLAY. Press the FF/SEARCH
B button so that ON appears
beside ONE TIME PLAY. Then,
press the STATUS/EXIT button.
• The real-time counter memory will
not function during Repeat Play
mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 42
42 A - B Repeat Play
Follow the steps below to program the TV/VCR to play the mate-
rial between two specified points (A and B) on a tape over and
over again.
Insert a tape in the TV/VCR.
1
2
1
Insert a tape in the TV/VCR.
POWER
MENU
STATUS/EXIT
CLEAR
2
1
2
3
MEMORY
Press the MENU button.
4
7
5
8
0
6
9
CHANNEL
ALT.CH
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
+100
SLEEP
SPEED
REMINDER
BRIGHTNESS
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
STOP/
PAUSE/STILL
5
3
Press the PLAY/▲ button or the STO P/▼ button to select
VCR SETUP, then press the FF/SEARCH B button.
VCR SETUP
> ONE TIME PLAY
REPEAT PLAY
ON-SCREEN MODE
RECORD DEFEAT
[ON]
[OFF]
SELECT KL CHOOSE
TO END PRESS EXIT
B
3-4
4
Press the PLAY/▲ button or the STO P/▼ button to select
REPEAT PLAY.
VCR SETUP
ONE TIME PLAY
> REPEAT PLAY
ON-SCREEN MODE
RECORD DEFEAT
[ON]
[OFF]
SELECT KL CHOOSE
TO END PRESS EXIT
B
Helpful Hints
• To cancel A-B Repeat Play, set ONE
TIME PLAY to ON. To set ONE
TIME PLAY to ON, follow steps 1 -
3 above. Then, press the PLAY/o
button or the STOP/p button to
select ONE TIME PLAY. Press the
FF/SEARCH B button so that ON
appears beside ONE TIME PLAY.
Then, press the STATUS/EXIT but-
ton.
5
Press the FF/SEARCH B button repeatedly so that A-B
appears beside REPEAT PLAY.
VCR SETUP
ONE TIME PLAY
> REPEAT PLAY
ON-SCREEN MODE
RECORD DEFEAT
[A-B]
[OFF]
SELECT KL CHOOSE
B
• The end position (B) must be later
on the tape than the start position
(A).
TO END PRESS EXIT
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 43
A - B Repeat Play (cont’d) 43
6
Press the STATUS/EXIT button to rem ove the display. A-
B REPEAT will appear on-screen. Beneath it, the letter A will flash
beside the real-time counter.
7-8
.
6
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
A-B REPEAT
0:12:34
4
7
5
8
0
6
9
A
CHANNEL
ALT.CH
+100
7
SLEEP
SPEED
Play, fast forward, or rewind the tape to the position at
which you want to begin playback. Stop the tape, then
press the MEMO RY button to set the start position (A).
The flashing A will become a flashing B.
VOLUME
MUTE
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
STOP/
PAUSE/STILL
.
A-B REPEAT
0:00:00
B
8
Play or fast forward the tape to the position at which you
want playback to end. Stop the tape, then press the
MEMO RY button to set the end position (B).
● The length of time between the start position (A) and the end
position (B) must be at least three minutes.
9
The TV/VCR will immediately rewind the tape to the start posi-
tion (A) and repeat playback to the end position (B) over and
over.
(TV programming will appear while the tape is rewinding.)
Helpful Hints
• The counter cannot be memorized
or reset when you are using this
feature.
• Positions A and B will be erased
when a tape is ejected or when you
press the REC(ord)/OTR button.
• A-B REPEAT will not appear on-
screen at step 6 if a tape is not in
the TV/VCR. NO CASSETTE will
flash on-screen briefly.
• You cannot rewind or fast forward
beyond points A or B when you are
using this feature.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 44
44 Real-Time Counter Memory
Follow the steps below to reset the real-time counter to zero at a
tape location you want to refer to later.
1
Play, fast forward, or rewind a tape to the location that
you would like to refer to later. Stop the tape.
2
3
POWER
MENU
STATUS/EXIT
CLEAR
2
1
2
3
MEMORY
Press the STATUS/EXIT button. The real-time counter will
appear on-screen.
4
7
5
8
0
6
9
4
CHANNEL
ALT.CH
01:08 PM
CH10
STOP
+100
SLEEP
SPEED
VOLUME
MUTE
SLP
1 : 23 : 45
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
STOP/
PAUSE/STILL
3
W hile the counter rem ains on-screen, press the CLEAR
button to reset the real-tim e counter to zero.
0 : 00 : 00
1,5
4
W hile the counter rem ains on-screen, press the MEMO-
RY button so that M appears on-screen. To erase a real-
time counter memory, press the MEMORY button so that the M
disappears from the screen.
M 0 : 00 : 00
5
To go to a tape location where the real-tim e counter was
reset to zero, press the REW (ind)/SEARCH s button or
the FF/SEARCH B button when playback is stopped.
W hen the tape reaches the point at which the counter
was set to zero, the tape will stop. Press the PLAY/o but-
ton to watch the tape.
Helpful Hints
• The real-time counter memory will
not function during Repeat Play
mode. Details are on page 41.
• You may only set one real-time
counter memory at a time. If you
try to set the real-time counter to
zero at a second location, the previ-
ous real-time counter to zero setting
will be lost.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 45
Automatic Operation Features 45
The following playback features will always operate.
Autom atic Playback
When you put a tape in the TV/VCR, the power will come on
automatically. If the tape’s record tab is missing, playback will
begin. If a timer recording is set, the power will not come on
automatically when you insert a tape with the record tab intact. If
a timer recording is set and the TV/VCR power is off, the
TV/VCR will eject the tape if the record tab is missing.
Autom atic Rewind, Eject, O ff
When a tape is played, fast forwarded, or recorded to its end, the
TV/VCR will rewind the tape, stop, turn itself off, and eject the
tape. If a real-time counter memory is set, the TV/VCR will only
rewind the tape to the point at which the counter was set to
zero, then stop. The TV/VCR will not turn itself off or eject the
tape.
Mem ory Rewind, Power O ff
When the POWER button is pressed while the TV/VCR is rewind-
ing a tape, REW → POWER OFF will appear on-screen. The
TV/VCR will turn itself off when the tape has finished rewinding.
If a real-time counter memory is set, the TV/VCR may only
rewind the tape to the point at which the counter was set to
zero, then turn itself off.
Tape Eject
A tape can be ejected with the TV/VCR power on or off (but the
TV/VCR must be plugged in). If a timer recording is programmed,
a tape can not be ejected when the power is off. Turn on the
TV/VCR power, then eject the tape. Be sure to insert a tape and
turn off the TV/VCR power for the timer recording.
Autom atic Tracking Adjustm ent
The TV/VCR automatically adjusts the tracking to give you the
best possible picture quality. With some recordings, however,
you may get a better picture using the manual tracking controls
(see below).
Manual Tracking
To adjust the tracking manually, press the CHANNEL o/p but-
tons on the TV/VCR.
Tracking returns to Automatic Tracking Adjustment when a tape
Before
Tracking
Adjustment
After
Tracking
Adjustment
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 46
46 Playback Options
Forward and Reverse Searching (SP/LP/SLP)
1
During tape playback, press and release the FF/SEARCH B button
or the REW(ind)/SEARCH { button. A fast forward or reverse
picture search will begin.
POWER
MENU
STATUS/EXIT
CLEAR
1
2
3
MEMORY
2
4
7
5
8
0
6
9
To return to normal playback, press the PLAY/▲ button.
CHANNEL
ALT.CH
+100
Super High Speed Searching (LP/SLP)
SLEEP
SPEED
VOLUME
MUTE
1
REW/SEARCH
REC/OTR
PLAY/
FF/SEARCH
During tape playback, press the FF/SEARCH B button or the
REW(ind)/SEARCH { button, then press again. The TV/VCR will
now search in super high speed.
STOP/
PAUSE/STILL
2
To return to normal playback, press the PLAY/▲ button.
Viewing a Still Picture
1
During tape playback, press the PAUSE/STILL button. A still pic-
ture will appear on-screen. The noise lines will move each time
you press the PAUSE/STILL button.
2
Helpful Hints
To release the still picture and return to normal playback, press
the PLAY/▲ button.
• Still mode will automatically switch
to Stop mode after five minutes to
protect the TV/VCR and the tape
from damage.
• SP/LP/SLP means this feature will
work with tapes recorded in
Standard Play, Long Play, or Super
Long Play. For details about tape
speed, see page 29.
• LP/SLP means this feature will work
with tapes recorded in Long Play
and Super Long Play. For details on
tape speed, see page 29.
• During forward and reverse search-
ing, horizontal noise bars will
appear on the TV/VCR screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 47
Specifications / Glossary 47
Glossary
Specifications
General
CRT: 13-inch in line gun
Television system: NTSC-M
AUDIO Jack: jack located on the front of the
TV/VCR which is used to record audio from anoth-
er source.
Closed caption system: Section 15.119, FCC
(Federal Communications Commission) Standard
Video Heads: Two heads
Tape width: 1/2 inch (12.65 mm)
Tape speed
Autom atic Channel Setup: process in which the
TV/VCR scans all available channels and places the
ones you receive in its memory. Then, when you
push the CHANNEL o/p buttons, you only scan
through channels you receive.
SP: 33.35 mm/sec.
LP: 16.67 mm/sec.
SLP: 11.12 mm/sec.
Bands: settings that allow you to tune channels.
• Antenna – VHF (very high frequency; channels 2
- 13) and UHF (ultra high frequency; channels 14
- 69).
• Cable – all standard channels can be received
without a Cable Box.
Operating Temperature: 41˚F (5˚C) to 104˚F (40˚C)
Relative Humidity: 10% to 75%
Power requirement: AC 120V, 60Hz
Power consumption: 75W
Sound output: 1W
Brightness: adjusting increases or decreases the
brightness of the color on-screen.
Dimensions:
15-13/16" (H) x 15-3/16" (W) x 14-3/4" (D)
402 mm x 386 mm x 375 mm
Weight: 27.5 lbs (12.5 kg)
Color: adjusting pales or brightens the TV/VCR
color.
Dubbing: copying a tape using a VCR.
HQ : high quality; a feature in the TV/VCR circuitry
which provides enhanced picture detail.
Tuner Broadcast Channels
VHF 2-13, UHF 14-69
Line Input: The channel to which you set your
TV/VCR during dubbing. The line input channel is
always channel 00 (A/V IN).
Cable TV Channels
Midband: A – 1
Superband: J – W
Hyperband: A-5 – A-1
Special Channel: 5A
Ultraband: 37 – 94, 100 – 125
Mode: a TV/VCR operation.
O TR: One-Touch Recording; programming a timed
recording that starts immediately and records for
30 minutes to eight hours, whichever you specify.
Picture: adjust to increase or decrease the con-
trast of the picture on-screen.
Term inals
Antenna IN: VHF/UHF 75 ohms unbalanced
Video IN: RCA connector
Audio IN: RCA connector
Earphone: 3.5 mm CES
Sharpness: adjusting softens or clarifies the picture
on-screen.
Tape Speeds: how fast the tape travels during
playback or recording.
• SP (standard play) – fastest tape speed (record-
ing time for a T120 tape is approximately two
hours); best picture quality.
• LP (long play) – average tape speed (recording
time for a T120 tape is approximately four
hours).
• SLP (super long play) – slowest tape speed
(recording time for a T120 tape is approximately
six hours).
Electrical Specifications
Video input level: 0.5~2.0Vp-p
Audio input level: -10dBv
Video S/N ratio
SP: More than 42dBµ
Audio S/N ratio
SP: More than 38dB
Designs and specifications are subject to change without
notice and without our legal obligation.
Tint: adjusting changes the tints of the picture on the
TV/VCR from purple to green.
VCR: video cassette recorder.
VIDEO Jack: jack located on the front of the
TV/VCR which is used to record video from anoth-
er source.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 48
48 Helpful Hints
If you are having problems with your product, check this list of problems and possible solutions before
requesting service. You may be able to solve the problem yourself.
If you need to call a customer service representative, please know the model number and serial number
of your product before you call. This information is displayed on the back of the product. Also, please
take a moment to identify the problem you are having, and be prepared to explain this to the representa-
tive. If you believe the representative will need to help you with operations, please stay near the product.
Our representatives will be happy to assist you.
Location
For safe operation and satisfactory performance of your TV/VCR, remember the following:
• Shield it from direct sunlight and keep it away from sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation. Do not block the ventilation openings at the top and bottom
of the TV/VCR. Do not place the TV/VCR on a carpet, as this will block the ventilation openings.
• Avoid locations subject to strong vibrations.
• Do not place the TV/VCR near strong magnetic fields.
• Do not move the TV/VCR from a cold place to a hot place, or vice versa.
Electrical Shock And Fire Hazards
• Do not handle the power cord with wet hands.
• Do not pull the power cord when disconnecting the TV/VCR from the AC (alternating current) wall
outlet. Grasp it by the plug.
• If water is spilled on the TV/VCR, unplug the power cord immediately and take the TV/VCR to an
authorized service center.
• Do not put your fingers or objects into the TV/VCR cassette compartment.
• Do not place anything on top of the TV/VCR.
Dew W arning (Moisture Condensation)
• Moisture may condense inside the unit when it is moved from a cold place to a warm place, after heat-
ing a cold room, or when the humidity is high. There is no warning that moisture has accumulated in
your TV/VCR. If you try to play a tape in a TV/VCR in which moisture has accumulated, the tape and
the TV/VCR could be damaged. If you think moisture may have accumulated inside the TV/VCR, keep
the TV/VCR power on (but do not play a tape) for at least two hours. This will allow the TV/VCR to
dry.
TV/VCR will not perform a tim er recording.
• Make sure the recording start and stop times are set correctly (pages 32 - 35). Midnight is 12 a.m.
Noon is 12 p.m.
• Make sure the TV/VCR power is off.
• Make sure the clock is set (pages 12 - 17).
• Make sure there is a tape in the TV/VCR. The tape must have a record tab.
• If the power fails, programmed timer recordings will be restored when the clock is reset. (The clock
will reset itself automatically if you are using the AUTO CLOCK feature. Details are on pages 14 - 17.
If you are not using the AUTO CLOCK feature, reset the clock manually. Details are on pages 12 -
13.) The timer recording will not occur only if the timer recording was scheduled to take place during
the power failure.
• Make sure RECORD DEFEAT is set to OFF (page 36).
TV/VCR will not record.
• Make sure the tape has a record tab (page five).
• Make sure RECORD DEFEAT is set to OFF (page 36).
• Plug the power cord into an active AC outlet (page seven).
• Check your hookups (pages six - seven).
• Set up the channels (page 10).
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 49
Helpful Hints (cont’d) 49
The rem ote control is not available, or the rem ote control will not access the pop up m enu.
• Use the buttons on the front panel of the TV/VCR to access the pop up menu (page 20). You can not
enter numbers (for example, to program a timer recording) using the front panel buttons.
TV/VCR has no power.
• Make sure the power plug is completely connected to an AC (alternating current) outlet.
TV/VCR power shuts off after 15 m inutes.
• To save energy, the TV/VCR will shut itself off after 15 minutes when it is on a channel that is not
receiving a broadcast signal (for example, a station that has gone off the air for the night). This is normal.
Channel reception is poor.
• Check connections, then set up the channels again (page 10).
TV/VCR does not have a picture.
• Adjust the antenna (page six).
• Adjust the TV/VCR picture controls (pages 24 - 25).
TV/VCR has poor sound or no sound.
• Adjust the volume.
• Press the MUTE button to restore the volume.
Tape playback is poor or tape is destroyed.
• Adjust the tracking. Details are on page 45.
• If moisture has accumulated in your TV/VCR, keep the power on for at least two hours, but do not try
to play a tape. Details are on page 48.
TV/VCR does not display closed captions.
• Make sure Counter Only is set to OFF. Details are on page 26.
• Make sure closed captioning is available for the program. Refer to the TV listings in your local newspa-
per.
Rem ote control does not operate TV/VCR.
• Aim the remote control directly at the TV/VCR’s remote sensor. Details are on pages five and 20.
• Remove all obstacles between the remote control and the TV/VCR.
• Inspect and replace the batteries in the remote control. Details are on page five.
Num ber buttons won’t work for channels above 69.
• Select CABLE from the INPUT section of the pop up menu, then let the TV/VCR set up the channels.
Details are on page 10.
TV/VCR can’t receive channels above 13.
• Select CABLE from the INPUT section of the pop up menu, then let the TV/VCR set up the channels.
Details are on page 10.
A tape can’t be inserted into the TV/VCR.
• Insert the tape window side up, with the record tab facing you.
• Make sure a tape isn’t already in the TV/VCR by pressing the STOP/EJECT button on the TV/VCR.
• Gently push on the center of the tape. Never force a tape into the TV/VCR.
• If a timer recording is set and the TV/VCR power is off, the TV/VCR will eject the tape if the record tab
is missing.
A tape can’t be rem oved from the TV/VCR.
• Make sure the power plug is completely connected to an AC (alternating current) outlet.
• If a timer recording is programmed, turn on the TV/VCR power, then eject the tape. Be sure to insert a
tape and turn off the TV/VCR power for the timer recording.
TV/VCR ejects the tape when you try to start a recording.
• Make sure the tape has a record tab. Details are on page five.
The cylinder rotates when tape playback is stopped.
• To enable the quick play mechanism, the cylinder will rotate for about five minutes. This is normal. The
quick play mechanism switches the tape mechanism from Stop to Play in just one second.
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 50
50 Limited Warranty
TV/VCR COMBINATION
90 Days Free Labor/One Year Free Parts Exchange (Two Years Free Exchange on Color Picture Tube)
This product must be carried in for repair.
WHO IS COVERED?
tribute the product, the local Philips service organiza-
You must have proof of purchase to receive warranty tion will attempt to provide service (although there
service. A sales receipt or other document showing
that you purchased the product is considered proof
of purchase.
may be a delay if the appropriate spare parts and
technical manual(s) are not readily available).
MAKE SURE YOU KEEP...
WHAT IS COVERED?
Please keep your sales receipt or other document
showing proof of purchase. Attach it to this owner’s
manual and keep both nearby. Also keep the original
box and packing material in case you need to return
your product.
Warranty coverage begins the day you buy your
product. For 90 days thereafter, all parts will be
repaired or replaced, and labor is free. From 90 days
to one year from the day of purchase, all parts will be
repaired or replaced, but you pay for all labor
charges. From one to two years from the day of pur-
chase, you pay for the replacement or repair of all
parts except the picture tube, and for all labor
charges. After two years from the day of purchase, you
pay for the replacement or repair of all parts, and for
all labor charges.
BEFORE REQUESTING SERVICE...
Please check your owner’s manual before requesting
service. Adjustments of the controls discussed there
may save you a service call.
TO GET WARRANTY SERVICE IN U.S.A., PUER-
TO RICO OR U.S. VIRGIN ISLANDS...
Take the product to a Philips factory service center
(see enclosed list) or authorized service center for
repair. When the product has been repaired, you
must pick up the unit at the center. Centers may
keep defective parts.
All parts, including repaired and replaced parts, are
covered only for the original warranty period. When
the warranty on the product expires, the warranty on
all replaced and repaired parts also expires.
WHAT IS EXCLUDED?
Your warranty does not cover:
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all
implied warranties, including implied warranties of
merchantability and fitness for a particular purpose,
are limited in duration to the duration of this express
warranty. But, because some states do not allow limi-
tations on how long an implied warranty may last, this
limitation may not apply to you.)
• labor charges for installation or setup of the prod-
uct, adjustment of customer controls on the prod-
uct, and installation or repair of antenna systems
outside of the product.
• product repair and/or part replacement because of
misuse, accident, unauthorized repair or other
cause not within the control of Philips Consumer
Electronics Company.
• reception problems caused by signal conditions or
cable or antenna systems outside the unit.
• a product that requires modification or adaptation
to enable it to operate in any country other than
the country for which it was designed, manufac-
tured, approved and/or authorized, or repair of
products damaged by these modifications.
• incidental or consequential damages resulting from
the product. (Some states do not allow the exclu-
sion of incidental or consequential damages, so the
above exclusion may not apply to you. This
includes, but is not limited to, prerecorded materi-
al, whether copyrighted or not copyrighted.)
• damage caused by the use of non-VHS tapes or
tapes that have not been tested and labeled for
use in two, four, six, and eight hour VHS
recorders.
TO GET WARRANTY SERVICE IN CANADA...
Please contact Philips at:
1-800-661-6162 (French Speaking)
1-800-363-7278 (English Speaking)
(In Canada, this warranty is given in lieu of all other
warranties. No other warranties are expressed or
implied, including any implied warranties of mer-
chantability or fitness for a particular purpose. Philips
is not liable under any circumstances for any direct,
indirect, special, incidental or consequential damages,
howsoever incurred, even if notified of the possibility
of such damages.)
REMEMBER...
Please record below the model and serial numbers
found on the product. Also, please fill out and mail
your warranty registration card promptly. It will be
easier for us to notify you if necessary.
• a product that is used for commercial or institu-
tional purposes.
MODEL # __________________________________
SERIAL # __________________________________
WHERE IS SERVICE AVAILABLE?
Warranty service is available in all countries where
the product is officially distributed by Philips
Consumer Electronics Company. In countries where
Philips Consumer Electronics Company does not dis-
This warranty gives you specific legal rights. You may have
other rights which vary from state to state.
Philips Service Solutions Group, P.O . Box 555, Jefferson City, Tennessee 37760, (423) 475-8869
EL4963E004 / MAC 6108/ 1-98
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 51
Index 51
a-b repeat play . . . . . . . .42 - 43
accessories . . . . . . . . . . . . . . .52
ant(enna) jack . . . . . . . . . . .6, 21
audio jack . . . . . . . . . . .7, 20, 31
automatic
menu
button . . . . . . . . . . . . . . . .22
front panel button access . .20
mute button . . . . . . . . . . . . . .23
tape
duplication . . . . . . . . . . . . .31
speed . . . . . . . . . . . . . .29, 47
time
setting . . . . . . . . . . . . .12 - 17
zone . . . . . . . . . . . . . . . . . .19
timer recording
cancelling . . . . . . . . . . . . . .35
reviewing . . . . . . . . . . . . . .35
setting . . . . . . . . . . . . .32 - 34
tint, adjusting . . . . . . . . .24 - 25
tracking . . . . . . . . . . . . . . . . .45
playback . . . . . . . . . . . . . . .45
rewind . . . . . . . . . . . . . . . .45
number buttons . . . . . . . . . . .22
one-touch recording . . . . . . . .30
batteries . . . . . . . . . . . . . . . . . .5
brightness, adjusting . . . .24 - 25
pause/still button . . . . . . .23, 46
picture, adjusting . . . . . . .24 - 25
play button . . . . . . . . . . . .20, 22
playback options . . . . . . . . . . .46
playing . . . . . . . . . . . . . . . . . .28
power
channel
above 100 . . . . . . . . . . . . .22
adding . . . . . . . . . . . . . . . .11
deleting . . . . . . . . . . . . . . .11
reviewing . . . . . . . . . . . . . .11
setup . . . . . . . . . . . . . . . . .10
o/p buttons . . . . .20, 23, 45
clear button . . . . . . . . . . . . . .23
clock . . . . . . . . . . . . . . . .12 - 17
closed caption system . . .38 - 39
color, adjusting . . . . . . . .24 - 25
connections . . . . . . . . . . . .6 - 7
contents, table of . . . . . . . . . . .4
controls
video jack . . . . . . . . . . .7, 20, 31
volume bar . . . . . . . . . . . . . . .40
button . . . . . . . . . . . . .20, 22
cord . . . . . . . . . . . . . . . . . . .7
warranty . . . . . . . . . . . . . . . . .50
real-time counter memory . . .44
rear panel . . . . . . . . . . . . . . . .21
rec/otr button . . . . . . . . .20, 22
rec(ord) light . . . . . . . . . . . . .20
recording . . . . . . . . . . . . . . . .29
reminder . . . . . . . . . . . . . . . .27
remote
remote . . . . . . . . . . . .22 - 23
tv/vcr . . . . . . . . . . . . .20 - 21
counter only mode . . . . . . . . .26
control
buttons . . . . . . . . .22 - 23
using . . . . . . . . . . . . . . . .5
sensor . . . . . . . . . . . . . . . .20
repeat play . . . . . . . . . . . . . . .41
rerecording . . . . . . . . . . . . . .31
rew(ind) button . . . . .20, 22, 46
rewinding . . . . . . . . . . . . . . . .46
daylight-saving time . . . . . . . .18
defeat recording . . . . . . . . . . .36
duplication . . . . . . . . . . . . . . .31
earphone jack . . . . . . . . . . . . .20
erasure prevention . . . . . . . . . .5
safety precautions . . . . . . . . . .3
searching . . . . . . . . . . . . . . . .46
sensor (remote) . . . . . . . . . . .20
sharpness, adjusting . . . . .24 - 25
sleep timer . . . . . . . . . . . . . . .37
slp . . . . . . . . . . . . . . . . . .29, 47
smartclock . . . . . . . . . . .12 - 17
sp . . . . . . . . . . . . . . . . . .29, 47
standard play . . . . . . . . . .29, 47
status display . . . . . . . . . . . . .26
status/exit button . . . . . . . . . .22
still picture . . . . . . . . . . . . . . .46
stop button . . . . . . . . . . . . . .23
stop/eject button . . . . . . . . . .20
super high speed searching . . .46
super long play . . . . . . . . .29, 47
fast forward search . . . . . . . . .46
ff button . . . . . . . . . . .20, 23, 46
front panel . . . . . . . . . . . . . . .20
glossary . . . . . . . . . . . . . . . . .47
helpful hints . . . . . . . . . .48 - 49
hookups . . . . . . . . . . . .6 - 7, 31
language selection . . . . . . . . . . .9
line input mode . . . . . .10, 31, 47
long play . . . . . . . . . . . . . .29, 47
lp . . . . . . . . . . . . . . . . . .29, 47
memory
button . . . . . . . . . .23, 42 - 44
real-time counter . . . . . . . .44
rewind, power off . . . . . . .45
table of contents . . . . . . . . . . .4
Download from Www.Somanuals.com. All Manuals Search And Download.
CCZ130comb 4/5/99 7:32 PM Page 52
Check to be sure the items on this page are packed
with your TV/VCR. These accessories are provided to
help you use or set up your TV/VCR.
Rem ote Control (4835 218 37222)
Two AA Batteries (4835 138 17012)
If any of these items are not included, or if you need
to replace an item, contact Philips Service Solutions
Group at the address below.
Philips Service Solutions Group
P.O. Box 967
Greeneville, TN 37744-0967
Or, call 1-800-851-8885.
IB8025E001
Printed In Malaysia
0EMN01366 / B5913UP * * * * *
This owner’s manual is made of recycled paper.
Download from Www.Somanuals.com. All Manuals Search And Download.
|