Magnavox TV Converter Box TB100MG9 User Manual

Owner's Manual  
TB100MG9  
DTV Digital to Analog Converter  
(Set Top Box)  
THANK YOU FOR CHOOSING MAGNAVOX.  
NEED HELP FAST?  
READ YOUR OWNER'S MANUAL FIRST FOR QUICK TIPS  
THAT MAKE USING YOUR MAGNAVOX PRODUCT MORE ENJOYABLE.  
IF YOU HAVE READ YOUR INSTRUCTIONS AND STILL NEED ASSISTANCE,  
YOU MAY ACCESS OUR ONLINE HELP AT HTTP://WWW.FUNAI-CORP.COM  
OR CALL 1-800-605-8610 WHILE WITH YOUR PRODUCT.  
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.  
© 2008 Funai Electric Co., Ltd.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FIGURE A  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
ANTENNA LEAD  
INWIRE  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
GROUND CLAMP  
ELECTRIC SERVICE  
EQUIPMENT  
GROUNDING  
CONDUCTORS  
(NEC SECTION 810-21)  
NEC - NATIONAL  
ELECTRICAL CODE  
GROUND CLAMPS  
POWER SERVICE GROUNDING ELECTRODE  
SYSTEM (NEC ART 250, PART H)  
conductors, location of antenna-discharge unit,  
a. When the power-supply cord or plug is damaged  
or frayed.  
connection to grounding electrodes, and requirements  
for the grounding electrode. (Fig. A)  
b. If liquid has been spilled, or objects have fallen into  
14. Lightning - For added protection for this product  
receiver during a lightning storm, or when it is left  
unattended and unused for long periods of time,  
unplug it from the wall outlet and disconnect the  
antenna or cable system. This will prevent damage to  
this product due to lightning and power-line surges.  
15. Power Lines - An outside antenna system should not  
be located in the vicinity of overhead power lines or  
other electric light or power circuits, or where it can  
fall into such power lines or circuits. When installing an  
outside antenna system, extreme care should be taken  
to keep from touching such power lines or circuits as  
contact with them might be fatal.  
this product.  
c. If this product has been exposed to rain or water.  
d. If this product does not operate normally by  
following the operating instructions. Adjust only  
those controls that are covered by the operating  
instructions, as improper adjustment of other  
controls may result in damage and will often  
require extensive work by a qualified technician to  
restore this product to its normal operation.  
e. If this product has been dropped or damaged in  
any way.  
f. When this product exhibits a distinct change in  
performance-this indicates a need for service.  
16. Overloading - Do not overload wall outlets and extension  
20. Replacement Parts - When replacement parts are  
required, be sure the service technician has used  
replacement parts specified by the manufacturer that  
have the same characteristics as the original part.  
Unauthorized substitutions may result in fire, electric  
shock, injury to persons or other hazards.  
21. Safety Check - Upon completion of any service or  
repairs to this product, ask the service technician to  
perform routine safety checks to determine that this  
product is in proper operating condition.  
cords as this can result in a risk of fire or electric shock.  
17. Object and Liquid Entry - Never push objects of any  
kind into this product through openings as they may  
touch dangerous voltage points or short out parts that  
could result in a fire or electric shock. Never spill liquid  
of any kind on this product.  
18. Servicing - Do not attempt to service this product  
yourself as opening or removing covers may expose  
you to dangerous voltage or other hazards. Refer all  
servicing to qualified service personnel.  
22. Heat - This product should be situated away from heat  
sources such as radiators, heat registers, stoves, or other  
products (including amplifiers) that produce heat.  
19. Damage Requiring Service - Unplug this product from  
the wall outlet and refer servicing to qualified service  
personnel under the following conditions:  
The serial number of this product may be found on the bottom of the unit. You should record the number and  
other vital information here and retain this book as a permanent record. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
CAUTION:  
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY  
INSERT.  
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE  
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU  
FOND.  
Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling,  
standing or climbing on it. A falling unit can cause serious injury or even death.  
3
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Precautions  
Location  
Important Copyright Information  
For safe operation and satisfactory performance  
of this product, keep the following in mind when  
selecting a place for its installation:  
Unauthorized recording or use of broadcast  
television programming, video tape, film or other  
copyrighted material may violate applicable  
copyright laws. We assume no responsibility for the  
unauthorized duplication, use or other acts which  
infringe upon the rights of copyright owners.  
Shield it from direct sunlight and keep it away  
from sources of intense heat.  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for  
proper heat dissipation. Do not block the  
ventilation holes at the top and bottom of the  
product. Do not place the product on a carpet  
because this will block the ventilation holes.  
FCC WARNING - This equipment may generate  
or use radio frequency energy. Changes or  
modifications to this equipment may cause  
harmful interference unless the modifications  
are expressly approved in the instruction  
manual. The user could lose the authority to  
operate this equipment if an unauthorized  
change or modification is made.  
Install the product in a horizontal position.  
Avoid locations subject to strong vibration.  
Do not place this product near strong magnetic  
fields.  
Avoid moving this product to locations where  
temperature differences are extreme.  
Avoid the Hazards of Electrical  
Shock and Fire  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when  
disconnecting it from an AC wall outlet. Grasp it  
by the plug.  
If by accident, water is spilled on your the  
product, unplug the power cord immediately  
and take the product to our Authorized Service  
Center for servicing.  
Do not place anything directly on top of the  
product.  
A Note about Recycling  
This product’s packaging materials are recyclable  
and can be reused. Please dispose of any materials in  
accordance with your local recycling regulations.  
Batteries should never be thrown away or  
incinerated but disposed of in accordance with your  
local regulations concerning chemical wastes.  
4
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
T a b l e o f C o n t e n t s  
Before Using  
Advanced Operation  
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Information on Digital Broadcasting . . . . . . . . . . . . . . . 7  
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Location of Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Autoscan (Receiving Channels) . . . . . . . . . . . . . . . . . . . 18  
Adding/Deleting Channels . . . . . . . . . . . . . . . . . . . . . . . 18  
Adjusting Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Selecting Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Setting the Time Zone and D.S.T  
(Daylight Saving Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
V-chip Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Closed Caption Options . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Auto Power Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Viewing Analog TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Connections  
Connecting to a TV without A/V Jacks . . . . . . . . . . . . 10  
Connecting to a TV with A/V Jacks . . . . . . . . . . . . . . . . 10  
Connecting to a Cable Box (Optional). . . . . . . . . . . . . 11  
Connecting to Other Devices. . . . . . . . . . . . . . . . . . . . . 12  
Others  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Initial Setup (Setup Wizard)  
Initial Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover  
Basic Operation  
Selecting Channels on the STB . . . . . . . . . . . . . . . . . . . 15  
© 2008 Funai Electric Co., Ltd.  
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,  
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written  
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto  
is strictly prohibited.  
Information in this document is subject to change without notice. Funai reserves the right to change the  
content herein without the obligation to notify any person or organization of such changes.  
with the  
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way  
without the express written consent of Funai. All other trademarks used herein remain the exclusive property  
of their respective owners. Nothing contained in this manual should be construed as granting, by implication  
or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or  
any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property  
rights to the fullest extent of the law.  
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby  
Laboratories.  
5
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Overview  
CONNECTION  
Connecting to  
A
TV without  
A/V jacks  
SET TOP BOX  
P
P
10  
a TV without A/V jacks  
Conexión a un TV sin tomas de A/V  
Connecting to  
B
C
TV with  
A/V jacks  
SET TOP BOX  
10  
a TV with A/V jacks  
Conexión a un TV con tomas de A/V  
Connecting to  
Cable Box  
TV with  
A/V jacks  
SET TOP BOX  
P
11  
a Cable Box  
Conexión a una caja de  
cable  
Connecting to  
D
DVD or VCR  
TV with  
A/V jacks  
SET TOP BOX  
P
12  
Other Devices  
Conexión a otros  
dispositivos  
SETUP WIZARD  
1. Language for TV screen  
Idioma para la pantalla  
2. Connection for audio output  
Conexión para salida de audio  
3. Time zone  
Husos horarios  
P
14  
4. Daylight savings time (D.S.T)  
Hora de verano (D.S.T)  
5. Display mode  
modo de indicaciones  
6. Channel scanning  
Búsqueda de canales  
Viewing Analog TV  
P
27  
Viendo TV Analógica  
6
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Information on Digital Broadcasting  
This STB makes it possible to view the digital TV  
programs on your analog TV by converting the  
digital signal to the analog signal. You can use  
most features provided by the digital broadcast,  
except that the resolution of the image is always  
output in 480i (standard resolution).  
ATSC  
Receives  
ATSC  
Digital  
terrestrial signals  
Digital terrestrial  
antenna  
STB (Set Top Box)  
converts the ATSC signal  
to analog signal  
TV  
Accessories  
Check the following accessories when unpacking the STB:  
Remote control:  
NA387UD (x1)  
Owner’s manual:  
1VMN25974 (x1)  
AA battery (x2)  
RF cable:  
WPZ0901TM002 /  
WPZ0901TM005 (x1)  
Installing Batteries  
Instalación de pilas  
1
Unsnap the battery cover from the  
back of the remote control.  
2
Install two AA batteries making  
sure the polarity (+ / ) is correct.  
3
Snap the battery  
-
cover back.  
Cierre la cubierta de  
pilas.  
Abra la cubierta de pilas de la parte  
Instale dos pilas AA asegurándose que  
trasera del mando a distancia.  
la polaridad (+ / ) sea la correcta.  
-
CAUTION:  
NOTE:  
Do not mix battery types (alkaline and manganese, or old ones and  
new ones).  
No mezcle tipos de baterías (baterías alcalinas y de manganeso, ni pilas viejas  
con pilas nuevas).  
When replacing batteries,  
replace them in pairs.  
Do not recharge, short-circuit, heat, burn or disassemble batteries.  
No recargue, caliente, queme o desarme baterías ni provoque un corto circuito  
con ellas.  
Cuando cambie las pilas,  
hágalo por pares.  
Remove batteries from battery compartment that is not going to be  
used for a month or more.  
Quite las pilas del compartimento de pilas si no se va a utilizar durante un mes o más.  
7
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Using  
Location of Controls  
Ubicación del control  
Remote Control  
Mando a distancia  
1
STANDBY-ON button: Turns STB on and off.  
Conecta y desconecta el STB.  
2
3
4
Number buttons  
OK button  
1
2
SETUP button: Displays “SETUPmenu.  
Switches “RF OUTsetting by holding this button  
down over 3 seconds.  
Despliega el menú “AJUSTE.  
Cambia la configuración de “SALIDA RFal mantenerse  
presionado durante 3 segundos.  
7
8
9
10  
5
6
ALT. CH: Returns to the last selected channel.  
3
4
Regresa al último canal seleccionado.  
AUDIO button: Selects alternative audio  
languages (if available).  
Selecciona idiomas de audio alternativos (si existen).  
5
6
11  
12  
13  
7
. (Confirm) button: Press to confirm the channel  
selection made by [the Number buttons].  
Presione para confirmar la selección del canal, hecha  
con [los botones de Números].  
8
9
DISPLAY button: Displays the channel banner.  
Despliega el banner del canal.  
RETURN button: Returns to the previous menu  
screen.  
Regresa a la pantalla de menú anterior.  
10 Navigation buttons K / L / s /  
B
11 EPG button: Displays the Electronic Program  
Guide.  
Despliega la Guía Electrónica de Programas.  
12 CH K / Lbuttons  
13 STILL button: Freezes the image on the TV  
screen.  
Congela la imagen de la pantalla del TV.  
To operate this STB with a universal remote, check the instruction manual for remote and find  
Magnavox brand STB code. If you do not find the code or the code does not work, try to use Sylvania  
brand STB code instead.  
8
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Front Panel  
Panel frontal  
1
2
1
2
Remote control sensor  
POWER indicator:  
Turns green when the STB is in operation.  
Se vuelve verde cuando el STB está en operación.  
Rear Panel  
Panel trasero  
1
2
3
4 5  
1
2
AC power cord  
4
ANT. IN jack:  
Connect an antenna.  
Conecte una antena.  
AUDIO OUT jacks (Right-red / Left-white):  
Connect your TV, stereo system or VCR etc. with  
standard audio cables.  
5
ANT. OUT jack:  
Conecte su TV, sistema estéreo o VCR, etc., con cables  
de audio estándares.  
Connect to the ANT. IN jack on your TV.  
Conecte a la toma ANT. IN de su TV.  
3
VIDEO OUT jack (yellow):  
Connect your TV or VCR etc. with a standard  
video cable.  
Conecte su TV o VCR, etc., con un cable estándar de  
video.  
9
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections  
1
2
3
4
Disconnect the AC power cords of the devices from the AC outlet.  
Desconecte los cables de alimentación de los aparatos del tomacorriente CA.  
Disconnect RF coaxial cable from antenna input jack of your TV.  
Desconecte el cable coaxial de RF del conector hembra de entrada de antena de su televisor.  
Make the connections as illustrated below.  
Efectúe las conexiones tal como se ilustra a continuación.  
Plug all AC power cords into AC outlets, then turn all devices on.  
Enchufe todos los cables eléctricos de CA en los tomacorrientes de CA y conecte la alimentación de todos los equipos.  
Connecting to a TV without A/V Jacks  
A
Conexión a un TV sin tomas de A/V  
TV  
TV antenna  
Antena de TV  
STB  
RF cable  
(supplied)  
cable de RF  
(se incluye)  
Connecting to a TV with A/V Jacks  
B
Conexión a un TV con tomas de A/V  
TV  
TV antenna  
Antena de TV  
STB  
Audio cable  
cable de audio  
Video cable  
cable de  
video  
NOTE:  
If your TV has only one audio jack, connect the AUDIO OUT jack (L) (white) on the STB to the audio input  
jack on the TV.  
Si su TV sólo tiene una toma de audio, conecte la toma AUDIO OUT (L) (blanco) del STB, a la toma de entrada de audio  
del TV.  
10  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to a Cable Box (Optional)  
C
Conexión a una caja de cable (opcional)  
TV antenna  
Antena de TV  
TV  
STB  
Cable TV  
company  
empresa de  
TV por cable  
Audio cable  
cable de audio  
Video cable  
Cable box ((optional)  
caja dee caabblee (opciional)  
cable de video  
Incoming  
cable signals  
Señales del cable  
de entrada  
RF cable (supplied)  
cable de RF (se incluye)  
Note to the Cable TV System Installer:  
This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the National  
Electrical Code, which provides guidelines for proper grounding - in particular, specifying that the cable  
ground shall be connected to the grounding system of the building, as close to the point of cable entry as  
possible.  
Observación para el instalador del sistema de cable de TV:  
Este recordatorio se provee para alertar al instalador del sistema de cable de TV sobre el Artículo 820-40 del Código  
Eléctrico Nacional, el cual proporciona pautas para una puesta a tierra adecuada, y en particular especifica que la puesta  
a tierra del cable debe estar conectada al sistema de puesta a tierra del edificio, lo más cerca posible del punto de entrada  
del cable.  
11  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections  
Connecting to Other Devices  
D
Conexión a otros dispositivos  
TV antenna  
Antena de TV  
Splitter  
Divisor  
TV  
STB  
RF cable  
cable de RF  
Audio cable  
cable de audio  
DVD Recorder or VCR  
Grabaddor de DDVD o videoggrabador  
Audio cable  
cable de audio  
RF cable  
(supplied)  
cable de RF  
(se incluye)  
Video cable  
cable de video  
If your DVD recorder or VCR has only one audio jack, connect the AUDIO OUT jack (L) (white)  
on the STB to the audio input jack on the DVD.  
NOTE:  
Si su grabador de DVD o videograbador sólo tiene una toma de audio, conecte la toma AUDIO OUT (L)  
(blanco) del STB, a la toma de entrada de audio del DVD.  
12  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Initial Setup (Setup Wizard)  
Initial Setup  
Ajùste inicial  
1
Press [STANDBY-ON] on the remote control to activate the STB.  
Presione [STANDBY-ON] en el mando a distancia para activar el STB.  
lights up in green  
se vuelve verde  
2
Turn on the TV, and select the viewing channel (ch3 or external input channel) on  
your TV. (Refer to your TV’s manual.)  
Encienda el TV, y seleccione el canal que quiera ver (canal 3 o uno de entrada externo) en su TV. (Véase el  
manual del TV.)  
2
1
3
CH.  
CH.  
Appropriate Viewing Channel  
Configuración apropiada de el Canal de Visión  
Viewing  
STB  
Cable Box  
Ch3  
DVD or VCR  
Connection  
A
(p.10)  
“CH3”  
External input channel  
Canal de entrada externo  
B
(p.10)  
External input channel  
C
(p.11)  
(p.12)  
Canal de entrada externo  
External input channel  
Canal de entrada externo  
D
“CH3”  
If your TV’s ch3 is already occupied, select ch4, and set the STB’s output channel to ch4. You can  
switch ch3 / ch4 by holding [SETUP] down over 3 seconds.  
Si el c3 de su TV ya está ocupado, seleccione el c4 y luego ajuste el canal de salida del STB a c4. Puede alternar  
entre el c3 y 4 manteniendo presionado [SETUP] durante 3 segundos.  
”SETUP WIZARDscreen automatically appears.  
Follow the directions shown on the TV screen to set the each setting.  
13  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Initial Setup (Setup Wizard)  
7
Select “ON” or “OFF” for Daylight  
Saving Time (D.S.T) using [ s / B ],  
3
Select “CONTINUE” using [ s / B ],  
then press [OK].  
Seleccione “CONTINÚEutilizando [s / B] y presione  
then press [OK].  
[OK].  
Seleccione “ONu OFFpara la hora de verano. (D.S.T)  
utilizando [s / B] y presione [OK].  
This SETUP WIZARD will help you with the initial  
setup on your own.  
Select Daylight Saving Time.  
“CONTINUE”: To continue setup  
“CANCEL ”: To cancel to leave pre-arranged  
setup  
NOTE:  
2:00AM of the second Sunday in  
March until 2:00AM of the first  
Sunday in November.  
CANCEL  
CONTINUE  
4
5
Select the language using [ K / L ],  
ON  
OFF  
then press [OK].  
Seleccione el idioma utilizando [K / L] y presione [OK].  
8
Select the desired display mode  
using [ K / L ], then press [OK] (refer  
ENGLISH Select the language for setup display.  
ESPAÑOL Elija idioma de preparación.  
to page 20).  
FRANÇAIS Sélectionner langue écran config.  
Seleccione el modo de indicación deseado utilizando  
[K / L] y presione [OK].  
Select display mode.  
Select the connection for audio  
output using [ s / B ], then press [OK].  
Seleccione la conexión para salida de audio mediante  
[s / B] y luego presione [OK].  
LETTERBOX  
ZOOM  
FULL  
Select the connection for Audio output.  
9
Select “AUTOSCAN” using [ K / L ],  
AUDIO OUT : Connecting STB and TV via AUDIO  
Cable  
then press [OK].  
RF OUT  
: Connecting STB and TV via RF  
Cable  
Seleccione “AUTOEXPLO.mediante [K / L] y luego  
presione [OK].  
AUDIO OUT  
RF OUT  
The system is now scanning.  
Select “AUDIO OUT” if...  
- you are using the standard audio cable to  
connect the STB to your TV. (Connection or  
AUTOSCAN will rescan all channels.  
This may take a while to complete.  
B
12%  
EXIT  
Channel Found  
EXIT  
on pages 10 and 11.)  
C
AUTOSCAN  
Seleccione “AUDIO FUERA” si...  
- está utilizando el cable de audio normal para  
STB starts receiving available digital channels  
and stores them in the channel map.  
When the scanning is complete,  
conectar el STB a su TV. (conexión  
páginas 10 y 11.)  
o
en las  
B
C
Select “RF OUT” if...  
“AUTOSCAN COMPLETED” will be indicated.  
- you are using the RF cable to connect the STB  
to your TV. (Connection or on pages 10  
A
D
After autoscan is complete, use [CH K / L]  
to verify whether STB is receiving channels  
properly.  
and 12.)  
Seleccione “RF FUERA” si...  
- está utilizando el cable RF para conectar el STB a su  
TV. (conexión en las páginas 10 y 12.)  
o
A
D
The “SETUP WIZARD” is now complete.  
El “ASISTENTE DE PREP.” ahora ha finalizado.  
6
Select your time zone using [ K / L ],  
then press [OK].  
To cancel during scanning:  
Seleccione su huso horario con [K / L] y presione [OK].  
Press [SETUP] or [OK].  
Select Time Zone.  
Para cancelar durante la exploración: Presione [SETUP] o [OK].  
ATLANTIC  
EASTERN  
If autoscan is canceled, some channels not yet  
scanned may not be received. We recommend  
completing autoscan.  
You can do autoscan and adding / deleting  
channel later. Refer to page 18.  
CENTRAL  
MOUNTAIN  
PACIFIC  
ALASKA  
HAWAII  
14  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operation  
About Sub-channel Broadcasting  
Digital broadcasting offers a service that enables  
multiple signals, called “sub-channels, to be sent  
simultaneously on one main channel by using its  
high compression technology.  
Selecting Channels on the STB  
1
Enter the main channel number.  
If the main channel number is 1 digit, press [ . ]  
when finish entering.  
ATSC  
18:00  
CH4-1 (Soccer)  
2
Enter the sub-channel number.  
If the sub-channel number is 1 digit, press [OK]  
when finish entering.  
18:30  
(Soccer)  
(News)  
(Tennis)  
CH4-1  
CH4-2  
CH4-3  
E.g., selecting 6.1  
19:00  
CH4-1 (Soccer)  
E.g., selecting 26.12  
19:30  
20:00  
CH4-1 (Soccer)  
CH4-2 (News)  
: Can be changed by  
using [CH K / L ].  
NOTE:  
If you do not have a particular sub-channel  
number you want to select, enter the main  
channel number and then press [OK]. (If the  
main channel number is 1 digit, you should  
press [OK] twice.) The STB automatically tunes  
into the lowest sub-channel for the selected  
main channel.  
Press [ALT. CH] to return to the previously  
viewed channel.  
“NO SIGNALappears after the sub-channel  
broadcast is over.  
15  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operation  
Choosing Audio Language  
You can change languages when the channel  
provides alternate languages.  
Press [AUDIO] repeatedly.  
ENGLISH 1/4  
SPANISH 2/4  
FRENCH 3/4  
OTHER 4/4  
Audio language changes as follows.  
“OTHER” is indicated when the  
language is not English, Spanish  
nor French.  
NOTE:  
For international stations audio  
language will still be displayed as  
English.  
Picture Still  
You can freeze the image on the TV screen.  
Press [STILL].  
The image on the TV screen will be paused.  
To cancel still mode:  
Press any button except [STANDBY-ON].  
The sound output will not be  
paused.  
If “no signal” is detected or protected  
signal is received during still mode,  
the image remains paused and the  
sound output will be muted.  
NOTE:  
If the TV is left on STILL for a long  
period of time, the still image may  
cause a burn-in effect damaging the  
TV screen.  
16  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Channel Banner  
The channel banner provides you with the information on the selected channel.  
Press [DISPLAY].  
Station name  
SMILE  
ABC-XXX  
ENGLISH 1/2  
SIGNAL 50  
Program title  
Channel number :  
Audio language  
3.1  
CC  
Information Icons  
CC (Closed Caption):  
Signal strength :  
Indicates the signal strength of  
the current channel.  
Indicates that the program being  
broadcast is available with closed  
captioning.  
RESTRICTED PROGRAM  
TV-Y7 FV  
Program ratings :  
LOCK:  
Displays all the available ratings.  
Active ratings are highlighted in  
red.  
Indicates that the current program  
is blocked according to your V-chip  
setting.  
To remove the channel banner:  
Press [DISPLAY].  
Electronic Program Guide (EPG)  
Electronic Program Guide (EPG) is the electronic equivalent of a printed TV program guide.  
You can view a list of programs scheduled for the next few hours up to the next seven days.  
To display the correct information on “EPG, TIME ZONEand ”D.S.Tmust be set correctly.  
1
Press [EPG] while watching TV.  
Closed Caption :  
Indicates that the program being  
broadcast is available with closed  
captioning.  
CC  
EPG  
3.1  
Program title  
SMILE Prog 2  
ABC-XXX  
12:00PM-1:00PM  
SMILE 2-1  
SMILE 2-2  
SMILE 2-3  
Time segment for the program.  
“NOW” icon will be displayed on  
Channel number  
the right for the current program.  
PREV  
NEXT  
Indicates that there is a program  
information available for next or  
previous program.  
Program description  
2
Select the desired program using [ s / B ].  
To remove the EPG:  
Press [EPG].  
“EPG” will be cleared after 5 minutes.  
For channel numbers with blank description, the broadcasting station may not  
provide signals for “EPG.  
NOTE:  
When the program description consists of more than 4 lines, use [ K / L ] to scroll  
up / down in the list.  
17  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Advanced Operation  
To cancel during scanning:  
Press [SETUP] or [OK].  
Autoscan  
(Receiving Channels)  
NOTE:  
Autoscan receives available digital channels and  
stores them in a channel map.  
If canceled, some channels not yet scanned may  
not be received. We recommend completing  
autoscan.  
When you want to completely refresh the  
channel map, delete all the channels, then do  
the autoscan again. See “Adding/Deleting  
Channels” on this page for details.  
CAUTION:  
If autoscan is skipped, digital channels may not  
be received correctly.  
1
2
Press [SETUP].  
Select “CHANNELusing [ K / L ],  
then press [OK].  
When “NO SIGNALappears on the TV screen:  
Verify the antenna connection, then scan again.  
The STB tunes in channel 2-1 and “NO SIGNAL”  
appears if the STB could not receive any channels.  
3
Select “AUTOSCAN” using [ K / L ],  
then press [OK].  
CHANNEL  
Adding/Deleting Channels  
EXIT  
ADD/DELETE  
CHANNEL  
ANTENNA  
TIME  
AUTOSCAN  
Add or delete desired channels in the channel map.  
DETAIL  
RF OUT  
INITIAL  
CAUTION:  
You cannot recover the deleted channels once  
they are deleted unless you perform the  
autoscan again.  
4
Select “AUTOSCAN” using [ K / L ],  
then press [OK].  
AUTOSCAN  
1
2
Press [SETUP].  
Select “CHANNELusing [ K / L ],  
EXIT  
AUTOSCAN will rescan all channels.  
This may take a while to complete.  
CHANNEL  
then press [OK].  
TIME  
BACK  
AUTOSCAN  
DETAIL  
SETUP  
INITIAL  
EXIT  
ADD/DELETE  
CHANNEL  
ANTENNA  
TIME  
AUTOSCAN  
DETAIL  
INITIAL  
RF OUT  
AUTOSCAN  
The system is now scanning.  
3
Select “ADD/ DELETE” using [ K / L ],  
then press [OK].  
12%  
EXIT  
Channel Found  
CHANNEL  
STB starts receiving available digital  
channels and stores them in the channel  
map.  
EXIT  
ADD/DELETE  
CHANNEL  
ANTENNA  
TIME  
AUTOSCAN  
DETAIL  
When the scanning is complete,  
“AUTOSCAN COMPLETED” will be indicated.  
After autoscan is complete, use [CH K / L]  
to verify whether STB is receiving channels  
properly.  
RF OUT  
INITIAL  
18  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Add  
Delete  
4
With “ADD” selected, enter the main  
channel number you want to add,  
then press [OK] or wait for a few  
seconds to fix the number.  
If the main channel number is 1 digit, press [0]  
first.  
4
5
Select “DELETE” using [ K / L ], then  
press [OK].  
ADD/DELETE  
10.1  
EXIT  
ADD  
10  
20  
26  
56  
CHANNEL  
TIME  
DELETE  
DETAIL  
INITIAL  
NOTE:  
Select the channel number you want  
to delete from the channel list on the  
right using [ K / L ], then press [OK].  
Entering sub-channel number is not required.  
5
Press [OK] again to add the channel  
to the channel map.  
E.g., deleting channel 26.  
E.g., adding channel 6  
ADD/DELETE  
26.1  
EXIT  
ADD  
(or leave for  
a few seconds)  
10  
20  
26  
58  
CHANNEL  
TIME  
DELETE  
DETAIL  
INITIAL  
ADD/DELETE  
6.X  
ADD/DELETE  
EXIT  
58.1  
ADD  
6
10  
20  
58  
CHANNEL  
TIME  
DELETE  
EXIT  
CHANNEL  
TIME  
ADD  
10  
20  
58  
60  
DETAIL  
INITIAL  
DELETE  
DETAIL  
INITIAL  
E.g., adding channel 26.  
The selected channel is now deleted.  
To continue deleting:  
(or leave for  
a few seconds)  
Repeat step 5.  
6
Press [SETUP] to exit.  
ADD/DELETE  
26.X  
EXIT  
CHANNEL  
TIME  
ADD  
6
10  
20  
26  
DELETE  
DETAIL  
INITIAL  
The selected channel is now added.  
To continue adding:  
Repeat steps 4 and 5.  
6
Press [SETUP] to exit.  
19  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Advanced Operation  
Adjusting Antenna  
Selecting Display Mode  
You can verify the signal strength of each channel.  
You can adjust the aspect ratio of the digital TV  
program to fit your 4:3 TV monitor.  
1
Select a channel to adjust using [the  
Number buttons] or [CH K / L].  
Display Mode  
2
3
Press [SETUP].  
Select “CHANNELusing [ K / L ],  
then press [OK].  
Select “ANTENNA” using [ K / L ],  
1
2
Press [SETUP].  
Select “DETAILusing [ K / L ], then  
press [OK].  
4
SETUP  
then press [OK].  
EXIT  
V-CHIP  
CHANNEL  
CHANNEL  
CLOSED CAPTION  
TIME  
DISPLAY MODE  
LETTERBOX  
4 HOURS  
EXIT  
DETAIL  
INITIAL  
AUTO POWER DOWN  
ADD/DELETE  
CHANNEL  
ANTENNA  
TIME  
ADD/DELETE  
DETAIL  
RF OUT  
3
4
SelectDISPLAY MODEusing [ K / L ],  
then press [OK].  
INITIAL  
STB starts receiving the signal for the  
channel.  
DETAIL  
EXIT  
V-CHIP  
CHANNEL  
CLOSED CAPTION  
5
By referring to the on-screen  
indication, adjust the antenna’s  
direction to get the best reception.  
Status bar:  
Stretches to the right as the signal  
strength gets stronger.  
TIME  
DISPLAY MODE  
LETTERBOX  
4 HOURS  
DETAIL  
INITIAL  
AUTO POWER DOWN  
Select the desired display mode  
using [ K / L ], then press [OK].  
Descriptions of each settings are explained  
in the “Information on Display Modeon the  
next page.  
*
ANTENNA  
10.1  
EXIT  
WEAK  
STRONG  
Select display mode.  
CHANNEL  
TIME  
NOW  
10  
LETTERBOX  
ZOOM  
50  
PEAK  
DETAIL  
INITIAL  
BACK  
FULL  
Peak indicator:  
Indicates the highest strength ever  
reached.  
5
Press [SETUP] to exit.  
To adjust other channels:  
Select the channel using [CH K / L], then adjust it.  
6
Press [SETUP] to exit.  
20  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Information on Display Mode  
Setting the Time Zone and  
D.S.T (Daylight Saving Time)  
LETTERBOX  
16:9 picture is scaled down  
until the both sides of the  
picture fits the 4:3 TV. Black  
bars appear on top and  
bottom of the TV screen.  
You need to select the time zone of your area and  
set D.S.T correctly to make use of the EPG and the  
Channel banner function.  
ZOOM  
1
2
Press [SETUP].  
Select “TIME” using [ K / L ], then  
press [OK].  
Displays the 16:9 image with  
the top and the bottom of  
the picture fit to the 4:3 TV  
screen. Both sides of the  
picture are cut off.  
Time Zone  
FULL  
16:9 image is squeezed into  
the 4:3 TV screen. No parts  
are cropped, but the picture  
gets distorted.  
3
Select “TIME ZONE” using [ K / L ],  
then press [OK].  
TIME  
EXIT  
EASTERN  
OFF  
TIME ZONE  
D.S.T  
CHANNEL  
TIME  
CAUTION:  
DETAIL  
INITIAL  
If the TV is left in LETTER BOX mode for a long period  
of time, the black bars may cause a permanent burn-  
in effect.  
4
5
Select your time zone using [ K / L ],  
then press [OK].  
Select Time Zone.  
ATLANTIC  
EASTERN  
CENTRAL  
MOUNTAIN  
PACIFIC  
ALASKA  
HAWAII  
Press [SETUP] to exit.  
21  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Advanced Operation  
4-a Enter 4-digit numbers except 4737  
as your password using [the Number  
buttons].  
D.S.T (Daylight Saving Time)  
3
4
5
Select “D.S.T” using [ K / L ], then  
press [OK].  
Enter exactly the same password again in  
“Confirm password.entry field.  
TIME  
EXIT  
V-CHIP  
EASTERN  
ON  
TIME ZONE  
D.S.T  
CHANNEL  
TIME  
EXIT  
Enter password.  
DETAIL  
INITIAL  
CHANNEL  
Confirm password.  
TIME  
DETAIL  
INITIAL  
Select “ON” or “OFF” using [ s / B ],  
then press [OK].  
CAUTION:  
D.S.T  
Select Daylight Saving Time.  
Do not forget the password. It will be used as  
your V-chip access password from the next time  
onward.  
EXIT  
NOTE:  
2:00AM of the second Sunday in  
March until 2:00AM of the first  
CHANNEL  
Sunday in November.  
TIME  
DETAIL  
ON  
OFF  
INITIAL  
4-b Enter the password using [the  
Number buttons].  
Press [SETUP] to exit.  
Asterisk(*) will substitute for your password.  
* * * *  
V-chip Options  
NOTE:  
V-chip reads the ratings for programs, then denies  
access to the programs which exceed the rating level  
you set. With this function, you can block certain  
programming inappropriate for children.  
If you forget the password, enter “4737” then  
proceed to “New Password” on page 24.  
1
2
Press [SETUP].  
Select “DETAILusing [ K / L ], then  
press [OK].  
3
Select “V-CHIP” using [ K / L ], then  
press [OK].  
DETAIL  
EXIT  
V-CHIP  
CHANNEL  
CLOSED CAPTION  
TIME  
DISPLAY MODE  
LETTERBOX  
4 HOURS  
DETAIL  
INITIAL  
AUTO POWER DOWN  
Password entry field will appear.  
If you have not created a password yet...  
- proceed to step 4-a.  
If you have already set a password...  
- proceed to 4-b.  
If you want to change the password...  
- proceed to “New Passwordon page 24.  
22  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
Select the desired rating type using  
K / L ], then press [OK].  
E.g., “TV RATING”  
MPAA Rating  
Rating  
[
Description  
Mature audience only  
X
higher  
lower  
V-CHIP  
NC-17  
No one under 17 admitted  
Restricted; under 17 requires  
accompanying parent or adult  
guardian  
Unsuitable for children under 13  
Parental guidance suggested  
General audience  
EXIT  
CHANNEL  
TIME  
MPAA RATING  
TV RATING  
R
CANADIAN ENGLISH RATING  
CANADIAN FRENCH RATING  
DOWNLOADABLE RATING  
CLEAR DOWNLOADABLE RATING  
NEW PASSWORD  
DETAIL  
INITIAL  
PG-13  
PG  
G
NR  
No rating  
NOTE:  
“DOWNLOADABLE RATING” will be available  
when the STB receives a digital broadcast which  
contains V-chip 2.0 signal.  
TV Rating  
Rating  
TV-MA  
Description  
If the broadcasting signal does not have the  
downloadable rating information, “Downloadable  
Rating is currently not available.will appear.  
This message will also appear when you try to  
access “DOWNLOADABLE RATING” after you  
have cleared the downloadable rating  
information, and the new information has not  
been downloaded since.  
Mature audience only  
higher  
lower  
Unsuitable for children under  
14  
TV-14  
TV-PG  
TV-G  
Parental guidance suggested  
General audience  
Appropriate for all children 7  
and older  
TV-Y7  
To clear the downloadable rating information  
and its setting, select “CLEAR DOWNLOADABLE  
RATING.  
TV-Y  
Appropriate for all children  
No rating  
None  
6
Select the desired rating using  
[
K / L ], then press [OK] repeatedly  
to switch between view and block.  
When the rating is blocked, will appear.  
E.g.,  
“MPAA rating”  
“TV rating”  
V-CHIP  
V-CHIP  
Select MPAA rating.  
Set TV rating.  
EXIT  
CHANNEL  
TIME  
EXIT  
CHANNEL  
TIME  
X
FV  
TV-MA  
TV-14  
TV-PG  
TV-G  
TV-Y7  
TV-Y  
None  
V
S
L
D
NC-17  
R
PG-13  
PG  
G
DETAIL  
INITIAL  
DETAIL  
INITIAL  
NR  
“Canadian English rating” “Canadian French rating”  
V-CHIP  
V-CHIP  
Set Canadian English rating.  
Set Canadian French rating.  
EXIT  
CHANNEL  
TIME  
EXIT  
CHANNEL  
TIME  
18+  
14+  
PG  
G
C8+  
C
18ans+  
16ans+  
13ans+  
8ans+  
G
DETAIL  
INITIAL  
DETAIL  
INITIAL  
E
E
23  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Advanced Operation  
To Set the Sub Ratings for “TV RATING.  
7
Press [SETUP] to exit.  
As for TV-MA, TV-14, TV-PG, or TV-Y7, you can further  
set the sub ratings to block specific elements of  
programming. To set the sub ratings, follow the step  
below.  
NOTE:  
Use [ K / L / s / B ] to select the desired rating  
or sub rating, then press [OK] repeatedly to switch  
between view and block. Sub rating status will  
appear beside the main rating.  
When you select a rating and set it to block, the  
higher ratings will be blocked automatically.  
The lower ratings will be available for viewing.  
When you set the highest rating to view, all  
ratings will turn to view automatically.  
V-CHIP  
Set TV rating.  
EXIT  
FV  
V
S
L
D
New Password  
TV-MA  
TV-14  
TV-PG  
TV-G  
TV-Y7  
TV-Y  
CHANNEL  
TIME  
When you forget the password or when you want  
to change your password, follow the instructions  
below.  
DETAIL  
INITIAL  
None  
1
2
Press [SETUP].  
Select “DETAILusing [ K / L ], then  
press [OK].  
Select “V-CHIP” using [ K / L ], then  
press [OK].  
Enter 4737 in the password entry  
field.  
Sub Rating  
FV  
Description  
Fantasy Violence  
Violence  
Sexual Situation  
Coarse Language  
Suggestive Dialogue  
V
S
L
D
3
4
5
Changing the main rating to block or view  
automatically changes all its sub ratings to the  
same (block or view).  
SelectNEW PASSWORD” using  
[ K / L ], then press [OK].  
V-CHIP  
Canadian English Rating  
EXIT  
MPAA RATING  
TV RATING  
Rating  
Description  
Adult audience only  
Unsuitable for ages under 14  
Parental guidance suggested  
General audience  
For children over 8  
For all children  
Exempt program  
CHANNEL  
TIME  
CANADIAN ENGLISH RATING  
CANADIAN FRENCH RATING  
DOWNLOADABLE RATING  
CLEAR DOWNLOADABLE RATING  
NEW PASSWORD  
18+  
14+  
PG  
G
C8+  
C
higher  
lower  
DETAIL  
INITIAL  
6
Enter the new 4-digit password  
using [the Number buttons].  
Enter exactly the same password again in  
“Confirm password.entry field.  
E
V-CHIP  
EXIT  
Enter password.  
Canadian French Rating  
Rating Description  
18 ans+ Adult audience only  
16 ans + Unsuitable for ages under 16  
13 ans + Unsuitable for ages under 13  
CHANNEL  
Confirm password.  
TIME  
DETAIL  
INITIAL  
higher  
lower  
7
Press [SETUP] to exit.  
8 ans +  
G
E
Unsuitable for ages under 8  
General audience  
Exempt program  
24  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CC Style  
Closed Caption Options  
You need to setCC STYLEtoMANUALto customize  
your CC style.  
DTV has its own closed caption called DTV CC. Use  
this menu to change the settings for DTV CC.  
5
Select “MANUALusing [ K / L ],  
then press [OK].  
1
2
Press [SETUP].  
Select “DETAILusing [ K / L ], then  
press [OK].  
CC STYLE  
EXIT  
CC STYLE will be displayed using  
your manual setting.  
CHANNEL  
TIME  
AUTO  
3
Select “CLOSED CAPTION” using  
[ K / L ], then press [OK].  
DETAIL  
MANUAL  
DETAIL  
INITIAL  
If you select “AUTO...  
EXIT  
V-CHIP  
CHANNEL  
- the original CC style set by the broadcast  
station will be applied.  
CLOSED CAPTION  
TIME  
DISPLAY MODE  
LETTERBOX  
4 HOURS  
DETAIL  
INITIAL  
AUTO POWER DOWN  
If you select “MANUAL...  
- you can customize the CC style as you like.  
4
Select the desired closed caption  
item using [ K / L ], then press [OK].  
CLOSED CAPTION  
CC Style Edit  
You can edit the style of CC such as font, color or size,  
etc. This feature is available only when “CC STYLEis  
set to “MANUAL”.  
EXIT  
DTV CC  
OFF  
5
Select an item using [ K / L ], then  
press [OK]. Then use [ K / L ] to select  
the desired setting and press [OK].  
CHANNEL  
TIME  
CC STYLE  
CC STYLE EDIT  
AUTO  
DETAIL  
INITIAL  
DTV CC  
FONT STYLE  
FONT SIZE  
FONT0  
MIDDLE  
FONT COLOR  
FONT OPACITY  
BACK COLOR BLACK  
BACK OPACITY SOLID  
EDGE COLOR BLACK  
WHITE  
Digital TV has its own closed captions called DTV CC.  
Use this menu to change the settings for DTV CC.  
SOLID  
5
Select the desired DTV closed caption  
using [ K / L ], then press [OK].  
Select service.  
NONE  
EDGE TYPE  
Picture display  
Back  
OFF  
(Back Color and Back Opacity)  
SERVICE1  
SERVICE2  
SERVICE3  
SERVICE4  
SERVICE5  
SERVICE6  
Select if you do not want  
Off  
HI. EVERYONE  
HI. EVERYONE  
DTV CC. This is the default.  
Select one of these before  
Edge  
DTV CC  
changing any other item in  
Service 1~6 “CLOSED CAPTIONmenu.  
Choose “SERVICE1under  
(Edge Color and Edge Type)  
Font  
(Font Style, Font Size, Font Color and Font Opacity)  
normal circumstances.  
“DTV CCdiffers depending on the broadcast.  
6
Press [SETUP] to exit.  
25  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Advanced Operation  
Auto Power Down  
“Auto power downshuts down the STB  
automatically after a certain period of time you set.  
(The EPA (U.S. Environmental Protection Agency)  
recommends using this setting to conserve energy.)  
1
2
Press [SETUP].  
Select “DETAILusing [ K / L ], then  
press [OK].  
3
Select “AUTO POWER DOWN” using  
[ K / L ], then press [OK].  
DETAIL  
EXIT  
V-CHIP  
CHANNEL  
CLOSED CAPTION  
TIME  
DISPLAY MODE  
LETTERBOX  
4 HOURS  
DETAIL  
INITIAL  
AUTO POWER DOWN  
4
5
Select desired amount of time using  
[ K / L ], then press [OK].  
Select AUTO POWER DOWN time.  
OFF  
4 HOURS  
2 HOURS  
1 HOUR  
Select “OFF” to cancel the auto power down.  
Press [SETUP] to exit .  
26  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing Analog TV  
Viendo TV Analógica  
Method 1 Método 1  
You can view analog TV by switching “RF OUTsetting.  
Usted podrá ver TV analógica cambiando la configuración de “SALIDA RF.  
CONNECTION  
CONEXIÓN  
TV  
STB  
TV antenna  
Antena de TV  
RF cable (supplied)  
cable de RF (se incluye)  
Viewing Analog TV  
Viendo TV Analógica  
Viewing Digital TV  
Viendo TV Digital  
1
Press [STANDBY-ON] to activate the STB.  
1
2
Press [STANDBY-ON] to activate the STB.  
Presione [STANDBY-ON] para activar el STB.  
Presione [STANDBY-ON] para activar el STB.  
2
Select “RF THROUGH” in “RF OUT”  
Select “CH3” in “RF OUT” menu.  
(
Page 29)  
menu. ( Page 29)  
Seleccione “CH3” en el menú “SALIDA RF.  
Seleccione“TRAVÉS DE RFen el menúSALIDA RF.  
3
Select ch3 on your TV.  
3
Select the desired channel on your TV.  
Seleccione canal3 en su TV.  
Seleccione el canal deseado en su TV.  
ch3  
ch4  
2
1
H.  
C
.
H
C
ch6  
ch8  
3
2
You can view digital TV on ch3 of your TV.  
Usted podrá ver TV digital en el c3 de su TV.  
.
H
C
.
H
C
4
Select desired channel on the STB.  
Seleccione el canal deseado en el STB.  
You can view analog TV on your TV channel.  
Usted podrá ver TV analógica en su canal de TV.  
ch3  
ch3  
NOTE:  
ch3  
You cannot view Digital TV with this setting.  
With this setting, the analog TV signal can  
directly be sent to your TV.  
NOTE:  
You cannot view Analog TV with this setting.  
You can switch “RF THROUGH” to “CH3” by  
holding [SET UP] down over 3 seconds.  
Holding [SETUP] down over 3 seconds does  
not switch the setting back to “RF THROUGH.  
To switch the setting back to “RF THROUGH, follow  
the steps in “Setting RF OUT” on page 29.  
27  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Advanced Operation  
Method 2 Método 2  
You can view analog TV without switching “RF OUTsetting.  
Usted podrá ver TV analógica sin cambiar la configuración de “SALIDA RF.  
CONNECTION  
TV antenna  
Antena de TV  
TV  
STB  
Video cable  
cable de video  
Audio cable  
cable de audio  
RF cable (supplied)  
cable de RF (se incluye)  
Viewing Analog TV  
Viendo TV Analógica  
Viewing Digital TV  
Viendo TV Digital  
1
Press [STANDBY-ON] to activate the STB.  
1
Press [STANDBY-ON] to activate the STB.  
Presione [STANDBY-ON] para activar el STB.  
Presione [STANDBY-ON] para activar el STB.  
lights up in green  
se vuelve verde  
lights up in green  
se vuelve verde  
2
3
Select “RF THROUGH” in “RF OUT”  
2
Select external input channel on  
your TV.  
menu. ( Page 29)  
Seleccione el canal de entrada externo en su TV.  
Seleccione“TRAVÉS DE RFen el menúSALIDA RF.  
Select the desired channel on your TV.  
AUX  
Seleccione el canal deseado en su TV.  
H.  
C
.
H
C
ch4  
ch6  
ch8  
You can view digital TV on external input  
3
channel of your TV.  
2
.
H
C
.
H
C
Usted podrá ver TV digital en el canal de entrada  
externo de su TV.  
3
Select desired channel on the STB.  
You can view analog TV on your TV channel.  
Usted podrá ver TV analógica en su canal de TV.  
Seleccione el canal deseado en el STB.  
AUX  
AUX  
AUX  
28  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appropriate “RF OUT” Setting and Viewing  
Setting RF OUT  
Channel  
Configuración de SALIDA RF  
Configuración apropiada de “SALIDA RF” y el Canal de  
Visión  
If you want to enjoy analog TV channels also, you  
must set the “RF OUTsetting.  
ANALOG TV broadcast  
Transmisión de TV ANALÓGICA  
Default setting is “CH3.  
Si desea disfrutar también de los canales analógicos,  
Set “RF OUT” Tune your  
deberá configurar la “SALIDA RF.  
setting to  
TV to  
La configuración por defecto es “CH3.  
Ajuste “SALIDA Sintonice su  
RF” a  
TV a  
Connection  
1
2
Press [SETUP].  
Desired TV  
Presione [SETUP].  
Method 1 (p.27)  
“RF THROUGH” channel  
”TRAVÉS DE RF” Canal deseado  
en su TV  
Select “CHANNELusing [K / L], then  
Method 2 (p.28)  
press [OK].  
Seleccione “CANALutilizando [K / L] y presione  
DIGITAL TV broadcast  
Transmisión de TV DIGITAL  
[OK].  
Set “RF OUT” Tune your  
setting to TV to  
3
4
Select “RF OUT” using [K / L], then  
press [OK].  
Ajuste “SALIDA Sintonice su  
Seleccione “SALIDA RF” utilizando [K / L]  
y
RF” a  
TV a  
Connection  
presione [OK].  
Method 1 (p.27) “CH3”  
Ch3  
External input  
Select the desired setting using  
“RF THROUGH” channel  
Method 2 (p.28)  
[K / L], then press [OK].  
”TRAVÉS DE RF” Canal de entrada  
externo  
Seleccione la configuración deseada utilizando  
[K / L] y luego presione [OK].  
If your TV’s ch3 is already occupied, select ch4,  
and set the STB’s output channel to “CH4.  
Si el c3 de su TV ya está ocupado, seleccione el c4 y  
Switch RF OUT.  
If the screen doesn’t show anything  
after switching RF OUT, set the TV  
Channel to CH3, then hold down a  
“SETUP”button for 3 seconds.  
luego ajuste el canal de salida del STB a “CH4.  
RF THROUGH  
CH3  
CH4  
Using [SETUP] to Switch “RF OUT”  
Setting  
Utilizando [SETUP] para cambiar la configuración  
“SALIDA RF”  
5
6
Using [s / B], select “YES. Then,  
press [OK].  
Seleccione “SÍ” utilizando [s / B]. Luego,  
RF THROUGH  
over 3 seconds  
presione [OK].  
TRAVÉS DE RF  
durante 3 segundos  
RF OUT is RF THROUGH  
Are you sure ?  
YES  
NO  
If the screen doesn’t show  
anything after switching  
RF OUT, set the TV Channel  
to CH3, then hold down a  
“SETUP”button for 3 seconds.  
CH3  
CH4  
over 3 seconds  
durante 3 segundos  
Press [SETUP] to exit.  
Presione [SETUP] para salir.  
You cannot switch from “CH3 /  
CH4” to “RF THROUGH” with  
NOTE:  
[SETUP].  
No podrá cambiar de “CH3 / CH4” a  
“TRAVÉS DE RF” con [SETUP].  
29  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Others  
Troubleshooting  
Before requesting service, check the table below for a possible cause of the problem.  
Symptom  
Remedy  
Make sure that the AC power cord is securely plugged into the power  
No power  
outlet.  
Make sure to point the remote control at the remote control sensor.  
You may be too far from STB. Try moving closer.  
Remove any obstacles between the remote control and the remote  
control sensor.  
Make sure that the batteries are installed in the correct direction  
(+ and –). ( Page 7.)  
The batteries may be depleted. Replace them with new ones.  
The STB is not responding  
to the remote control.  
Make sure that the audio / video cables are correctly connected.  
Make sure that the TV is turned on.  
Make sure that the correct viewing channel (ch3 or external input  
channel) is selected on your TV. ( Page 13.) Refer to your TV’s manual  
for further information.  
No audio / picture  
Make sure the cables are not damaged.  
Make sure “RF OUT” setting is correct. ( Page 29.)  
Blocked noise on picture  
Make sure that the RF cable is connected correctly. ( Pages 10 - 12.)  
Make sure that “D.S.T” and “TIME ZONE” is set correctly. ( Page 21.)  
No EPG or the provided  
information is wrong  
Sound volume differs depending on the audio out setting. Select “RF  
OUT” at step 5 in the “Initial Setup (Setup Wizard). ( Page 14.)  
Low volume  
No reception  
Make sure to complete autoscan in “SETUP WIZARD” or in “SETUP”  
menu. When autoscan is not completed, some channels will not be  
received.  
The selected channel does not exist at that time. There are not always  
sub-channels being broadcast.  
Some channels with weak signal may not be received properly.  
This is not a malfunction.  
When you forget the  
password for V-chip  
If you forget the password, refer to “New Password. ( Page 24.)  
Closed captioning display  
(TEXT mode) does not go  
off even after changing  
channels through STB.  
Change the channel on your TV.  
Turn the TV off, and then on.  
The TV screen goes blank  
just after turning the STB  
on.  
This is a normal part of the start-up process and is not a malfunction.  
30  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Product  
DTV Digital to Analog Converter  
Tuner  
Receivable channels 2-69ch  
Connecting Jacks  
ANT. IN/OUT  
RF connector x2 (75ohm)  
Video Output  
RCA jack x1, 1Vpp (75ohm)  
Analog Audio Output  
RCA jack (L / R) x2  
2V rms (100k ohm)  
Power Source  
120V AC+/-10%, 60Hz+/-0.5%  
Power Consumption  
8W (Power on), Less than 1 W (Power o)  
Closed Caption System  
§15.122/FCC (digital CC)  
Operating Condition  
41°F (5°C) - 104°F (40°C)  
Dimensions (W x H x D)  
9.5" x 1.7" x 6"  
(240mm x 43mm x 150mm)  
Weight  
1.4lbs. (0.6Kg)  
Designs and Specifications are subject to change  
without notice.  
Fin  
31  
EN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship  
as follows:  
DURATION:  
PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date  
of original retail purchase. Certain parts are excluded from this warranty.  
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of  
original retail purchase.  
LIMITS AND EXCLUSIONS:  
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR OTHER  
PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO OBTAIN SERVICE  
UNDER THIS WARRANTY.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing  
or if service was attempted by an unauthorized service center. This limited warranty does not apply to any  
product not purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occur during normal use. It  
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or products  
not supplied by FUNAI CORP., or damage, which results from accident, misuse, abuse, mishandling,  
misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or  
office use of this product, or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY  
COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT  
OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS  
PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL  
OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS  
REPRESENTATIVES IN THE UNITED STATES.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER.  
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.  
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF  
OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIR COSTS WILL BE CHARGED.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM  
STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION  
WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT  
PRIOR NOTICE.  
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:  
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original  
packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER. FUNAI  
CORP. will not reimburse you for any service done by unauthorized service providers without prior written  
approval.  
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries, please  
contact us at:  
FUNAI SERVICE CORPORATION  
Customer Service  
Tel: 1-800-605-8610  
5653 Creekside Parkway, Suite A, Lockbourne, OH 43137  
Printed in China  
X6036UD / X6037UD  
1VMN25974 ★★★★★  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Land Pride Lawn Mower RCR26 Series User Manual
LG Electronics Cell Phone UX840H User Manual
Lindy Webcam 32849 User Manual
Lux Products Thermostat P521U User Manual
Magnavox Portable Stereo System AZ 9055 User Manual
Mazda Automobile 2008 Tribute HEV User Manual
McIntosh Speaker XR27 User Manual
Mellerware Blender 62200 User Manual
Meridian Audio Musical Instrument LD100 LD100U User Manual
Metra Electronics Automobile Accessories 99 8157B User Manual