Owner’s Manual
Manual del Propietario
Manuel du Propriétaire
55ME314V 39ME313V/F7 A
50ME314V
40ME314V
40ME324V
32ME304V
28ME304V
Necesita ayuda
inmediata?
1 866 341 3738
1 866 341 3738
1 866 341 3738
Download from Www.Somanuals.com. All Manuals Search And Download.
3
.English
to get the very most from your purchase.
Registering your model with MAGNAVOX makes you eligible for all of the valuable benefits listed below, so don't miss out.
Register Online at www.magnavox.com/support to ensure:
*Product Safety Notification
*Additional Benefits
By Registering your Product, you'll receive notification -
directly from the manufacturer - in the rare case of a
Product Recall or Safety Defect.
Registering your Product guarantees that you'll receive
all of the Privileges to which you're Entitled, including
special money-saving offers.
Know these safety symbols
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the apparatus’s enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the apparatus.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The caution marking is located on the rear or bottom of the cabinet.
WARNING:
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Apparatus shall
not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the
apparatus.
CAUTION:
ATTENTION
To prevent electric shock, match wide blade of plug to wide slot, fully insert.
:
Pour éviter les choc électriques,introduire la lame la plus large de la fiche dans la borne correspondante de la
prise et pousser jusqu’au fond.
CHILD SAFETY:
PROPER TELEVISION PLACEMENT MATTERS
THE CONSUMER ELECTRONICS INDUSTRY
CARES
WALL OR CEILING MOUNT YOUR
TELEVISION
•Manufacturers, retailers and the rest of the consumer
electronics industry are committed to making home
entertainment safe and enjoyable.
•ALWAYS contact your retailer about professional
installation if you have any doubts about your ability to
safely mount your television.
•As you enjoy your television, please note that all
televisions – new and old- must be supported on proper
stands or installed according to the manufacturer’s
recommendations. Televisions that are inappropriately
situated on dressers, bookcases, shelves, desks, speakers,
chests, carts, etc., may fall over, resulting in injury.
•ALWAYS use a mount that has been recommended by
the television manufacturer and has a safety certification
by an independent laboratory (such as UL, CSA, ETL).
•ALWAYS follow all instructions supplied by the
television and mount manufacturers.
•ALWAYS make sure that the wall or ceiling where you
are mounting the television is appropriate. Some mounts
are not designed to be mounted to walls and ceilings
with steel studs or cinder block construction. If you are
unsure, contact a professional installer.
•Televisions can be heavy. A minimum of two people is
required for a wall or ceiling mount installation.
TUNE IN TO SAFETY
•ALWAYS follow the manufacturer’s recommendations
for the safe installation of your television.
•ALWAYS read and follow all instructions for proper use
of your television.
•NEVER allow children to climb on or play on the
television or the furniture on which the television is
placed.
•NEVER place the television on furniture that can easily
be used as steps, such as a chest of drawers.
•ALWAYS install the television where it cannot be
pushed, pulled over or knocked down.
•ALWAYS route cords and cables connected to the
television so that they cannot be tripped over, pulled or
grabbed.
MOVING AN OLDER TELEVISION TO A NEW
PLACE IN YOUR HOME
•Many new television buyers move their older CRT
televisions into a secondary room after the purchase of a
flat-panel television. Special care should be made in the
placement of older CRT televisions.
•ALWAYS place your older CRT television on furniture
that is sturdy and appropriate for its size and weight.
•NEVER place your older CRT television on a dresser
where children may be tempted to use the drawers to
climb.
CE.org/safety
•ALWAYS make sure your older CRT television does
not hang over the edge of your furniture.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
.English
Important Safety Instructions
1. Read these instructions.
2. Keep thhese instructiions.
3. Heed all warnings.
4. Follow all instrructiions.
5. Do not use this apparatus neaarr wwaatteerr.
6. Clean only wiith dry cloth.
13.Unplug this apparatus during lightning storms or when
unused foor long pperiodss of timee.
14.Refer all servicing to qualifieed serrvicee ppersonnel.
Servicing is required when the apparatus has been
damageed in anny wayy,, such aas poweer-suppply cord or
plug is damageed, liquid has been spilled or objects
have falllen into the appaaratuss,, the appparaattus hass been
exposed tto rain or moisture, does not operate
normally,, or has bbeen drroopped.
7. Do not block any veentilaationn openings.. Insttaall in
accorddance wwith tthhe manuufactuurer’ss instructions.
8. Do not install near any heat soourcees suchh as radiators,
heat registers, stoves, oor otheer appaaratuss (inclluding
amplifieers) that produuce heat.
9. Do not defeat the safety puurpose of the polarized or
grounding type plug.A polarized plug has two blades
with one wider thhan thhee otherr.A grooundinng type pluugg
has two bbladess and a tthirdd ggrroouunnddiinngg pprroonngg..TThhee wwiiddee
blade or the third prong are provided for your ssafetty. If
the providded pluug doess not fitt into yyour ouuttlet, cconsult
an electrician for rreplaccementt of thee obsollete ouutlet.
Note to tthe CATV syystem insstaller:
This reminder is proviided too call thhe CATVV systeemm instaaller’s
attentioon to Artiicle 820--40 of thee NEC thatt providees gguuiiddeelliinneess ffoorr
proper grounding and, in particular, specifies that the cable ground
shall be cconnected tto the grrooundingg ssystem oof the buiilding,, aas close
to the point of cable entry as practical.
Examplee of Anteenna Grrounddiing as pper NEECC - Natiional
Electric Code
10.Prottect thhe powweer corrdd from bbeingg wwalkedd on or
pinchedd particuularly aat plugss, convveenniieennccee rreecceeppttaacclleess,,
and the point where they exit from the apparatus.
GROUND CLAMP
ANTENNA LLEAD INWIRE
11.Only uuse attachhmentss / acceessoriies speccifiedd by the
ANTENNA DIISCHARGE UNIT
(NEC SECTION 810-20)
manufactturer.
GROUNDING COONDUCTORS
(NEC SECTIION 810-21)
GROUND CLAMPS
12.Use only with the cart, stand, tripod, bracket, or
table speciified byy tthhee mmaannuuffaaccttuurreerr,, oorr
sold with the apparatus.When a cart
is used, usse cauttiion whenn moving the
cart / apparratus combination to avoid
injury from tip-over.
POWER SERRVICE GROOUUNDING ELLECTRODE
ELECTRIC SERVICE EQUIPMENT
SYSTEMM (NEC ARRT 250,, PPART H)
Wall Mount Bracket Kit
Funai is not liable for these types of accidents or injury
noted below.
Screw
dimension
Brand
Model #
• Install the Wall Mount Bracket on a sturdy vertical wall.
• If installed onto a ceiling or slanted wall, theTV and Wall
55ME314V
50ME314V
M6 x 0.472"
(12mm)
PLA50B
Mount Bracket may fall which could result in a severe injury.
• Do not use screws that are longer or shorter than their
specified length. If screws too long are used this may cause
mechanical or electrical damage inside theTV set. If screws
too short are used this may cause theTV set to fall.
• Do not fasten the screws by excessive force.This may
damage the product or cause the product to fall, leading to
an injury.
40ME314V
40ME324V
SAN25BB
SANUS
M4 x 0.472”
(12mm)
32ME304V
28ME304V
SAN18B
39ME313V/F7 A
SAN25BB
•
•
•
The recommended Wall Mount Bracket Kit (sold
separately) allows the mounting of theTV on the wall.
For detailed information on installing the wall mount,
refer to the Wall Mount Instruction Book.
Funai is not responsible for any damage to the product
or injury to yourself or others if you elect to install the
TV Wall Mount Bracket or mount theTV onto the
Bracket on your own.
• For safety reasons use 2 people to mount theTV onto a
Wall Mounting Bracket.
• Do not mount theTV onto the Wall Mounting Bracket
while yourTV is plugged in orTurned On. It may result in an
electrical shock injury.
When installing the unit on the wall, allow this much space.
Top:
11.8 inches (30cm)
5.9 inches (15cm)
3.9 inches (10cm)
•
The Wall Mount Bracket must be installed by experts.
Left and right side:
Bottom:
Download from Www.Somanuals.com. All Manuals Search And Download.
5
.English
1 Notice
Modifications
This apparatus may generate or use radio frequency energy. Changes or
modifications to this apparatus may cause harmful interference unless
the modifications are expressly approved in the Owner’s Manual.
MAGNAVOX is a registered trademark of Philips North America
Corporation and is used by Funai Electric Co., Ltd. and Funai
Corporation, Inc. under license from Philips North America.
The user could lose the authority to operate this apparatus if an
unauthorized change or modification is made.
Funai reserves the right to change products at any time without being
Cables
obliged to adjust earlier supplies accordingly.
Connections to this device must be made with shielded cables with
metallic RFI / EMI connector hoods to maintain compliance with FCC
Rules and Regulations.
The material in this Owner’s Manual is believed adequate for the
intended use of the system. If the product or its individual modules or
procedures are used for purposes other than those specified herein,
confirmation of their validity and suitability must be obtained. Funai
warrants that the material itself does not infringe any United States
patents. No further warranty is expressed or implied.
Canadian notice
CAN ICES-3 (B)/NMB-3 (B)
StandardTelevision Receiving Apparatus, Canada BETS-7 / NTMR-7.
Funai cannot be held responsible neither for any errors in the content
of this document nor for any problems as a result of the content in
this document. Errors reported to Funai will be adapted and published
on the Funai support website as soon as possible.
Copyright
All other registered and unregistered trademarks are the property of
their respective owners.
Pixel characteristics
The terms HDMI and HDMI
This LCD product has a high number of color pixels.Although it has
effective pixels of 99.999% or more, black dots or bright points of light
(red, green or blue) may appear constantly on the screen.This is a
structural property of the display (within common industry standards)
and is not a malfunction.
High-Definition Multimedia Interface,
and the HDMI Logo are trademarks
or registered trademarks of HDMI
Licensing LLC in the United States
and other countries.
Warranty
No components are user serviceable. Do not open or remove covers
to the inside of the product. Repairs may only be done by Service
Centers and official repair shops. Failure to do so shall void any
warranty, stated or implied.
Manufactured under license from
Dolby Laboratories. Dolby and the
double-D symbol are trademarks of
Dolby Laboratories.
Any operation expressly prohibited in this Owner’s Manual, any
adjustments or assembly procedures not recommended or authorized
in this Owner’s Manual shall void the warranty.
For DTS patents, see
Manufactured under license from DTS
Licensing Limited. DTS, the Symbol, &
DTS and the Symbol together are
registered trademarks, and DTS
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits
for a Class B Digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
TruSurround is a trademark of DTS,
Inc. © DTS, Inc.All Rights Reserved.
ENERGY STAR® is a joint program of
the U.S. Environmental Protection
Agency and the U.S. Department of
Energy helping us all save money and
protect the environment through
energy efficient products and practices.
•
Reorient or relocate the receiving antenna.
Consumer Notice:
•
Increase the separation between the equipment and the
receiver.
ThisTV has been set to maximize energy efficiency while delivering
the best possible picture using the factory installed home mode
settings.
Changing or enabling other features in thisTV (e.g. brightened
backlighting) will possibly increase energy consumption beyond the
original ENERGY STAR® qualified limits.
Portions of this software are copyright ©The FreeType Project
(www.freetype.org).
TheAmericanAcademy of Pediatrics discourages television viewing
for children younger than two years of age.
•
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio or television
technician for help.
Declaration of Conformity
Trade Name
Responsible Party
Model
: MAGNAVOX
: FUNAI CORPORATION, Inc.
: 55ME314V, 50ME314V, 40ME314V,
40ME324V, 32ME304V, 28ME304V,
39ME313V/F7 A
© 2013 Funai Electric Co., Ltd.All rights reserved.
No part of this Owner’s Manual may be reproduced, transmitted,
disseminated or transcribed, in any form or for any purpose without
the express prior written consent of Funai. Furthermore, any
unauthorized commercial distribution of this Owner’s Manual or any
revision hereto is strictly prohibited.
Address
: 19900 Van Ness Avenue, Torrance, CA
90501 U.S.A.
Telephone Number
: 1 866 341 3738
Download from Www.Somanuals.com. All Manuals Search And Download.
6
.English
2 Important
Environmental Care
Positioning the TV
•
•
•
•
Large screenTVs are heavy. 2 people are required to carry and
handle a large screenTV.
The packaging of this product is intended to be recycled.
Make sure to hold the upper and bottom
frames of the Unit firmly as illustrated.
Contact your local authorities for information about how to recycle
the packaging.
Install the Unit in a horizontal and stable
position.
For product recycling information, please visit - www.magnavox.com
Do not install the Unit in direct sunlight
or in a place subject to dust or strong
Click on
vibration.
•
Depending on the environment, the
temperature of this Unit may increase slightly.This is not a
malfunction.
End of Life Directives
Magnavox pays a lot of attention to produce environmental-friendly
products in green focal areas.Your newTV contains materials which
can be recycled and reused.At the end of its life, specialized
companies can dismantle the discardedTV to concentrate the
reusable materials and to minimize the amount of materials to be
disposed of. Please ensure you dispose of your oldTV according to
local regulations.
•
•
•
Avoid a place with drastic temperature changes.
Do not place anything directly on top or bottom of the Unit.
Depending on your external devices, noise or disturbance of
the picture and / or sound may be generated if the Unit is
placed too close to them. In this case, please ensure enough
space between the external devices and the Unit.
Do not insert the AC power cord into the power socket outlet
before all the connections are made.
•
•
•
•
Ensure that you always have easy access to the AC power cord
or plug to disconnect theTV from the power.
Before you move theTV, disconnect attached cables to prevent
damage to connectors.
Disposal of Used Batteries
The Batteries supplied do not contain the heavy metals mercury
and cadmium. Nevertheless, in many areas Batteries may not be
disposed of with your household waste. Please ensure you dispose
of Batteries according to local Regulations.
Be sure to unplug the AC power cord from the AC outlet
before moving or carrying the Unit.
Preparing to Move/Ship the Unit
Please pack the Unit properly by following the Diagram on the
Carton.
Regulatory Notices
Do not place the Unit on the furniture that is capable of being tilted by
a child and an adult leaning, pulling, standing or climbing on it. A falling
Unit can cause serious injury or even death.
This apparatus should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided.
Make sure to leave a space of 4 inches (10cm) or more around this
apparatus.
1
2
3
4
Press to turn the Unit on and go into standby mode.
To completely turn off the Unit, you must unplug the AC power cord.
Disconnect the AC plug to shut the Unit off when trouble is found or
not in use. The AC plug shall remain readily available.
To avoid damage to the Screen, do not pack the stand on the
same side as theTV screen.
AC plug
Never use a gas duster on this TV.
The gas trapped inside of this Unit may cause ignition and explosion.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
WARNING: Batteries (battery pack or battery installed) shall
not be exposed to excessive heat such as sunshine,
fire or the like.
WARNING: To prevent injury, this apparatus must be securely
attached to the furniture / wall in accordance with
the instructions. Tipping, shaking or rocking the
unit may cause injury / death.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
.English
3 Getting Started
Supplied Accessories
Owner’s Manual
Quick Start guide
Features
●
DTV / Analog TV / CATV
You can use your Remote Control to select channels which are Broadcast in Digital format
and conventional Analog format. Also, Cable and Satellite subscribers can access their TV
channels.
●
Information display
Remote Control
and Batteries
TV base and Screws
You can display on the TV screen the Title, contents (DTV only) and other information on
the current Program.
(AAA, 1.5V x 2)
●
Autoprogram
This Unit Automatically scans and memorizes channels available in your area, Eliminating
difficult Setup procedures.
Screws packed with this Unit.
●
Child lock
Model
55ME314V
50ME314V
40ME314V
40ME324V
39ME313V/F7 A
32ME304V
28ME304V
Quantity
Size
This feature allows you to Block children’s access to inappropriate Programs.
●
M4 x 0.472”(12mm)
M4 x 0.787”(20mm)
M4 x 0.551”(14mm)
Closed Caption decoder
8
Built-in Closed Caption decoder displays text for Closed Caption supported Programs.
●
MTS / SAP tuner
Audio can be selected from the Remote Control.
●
Auto Standby
3
If there is no Input Signal and no operation for 15 minutes, the Unit will go into Standby
mode Automatically.
●
Sleep Timer
You can set the Unit to go into Standby mode after a specific amount of time.
Cable management tie*
●
Choices for On-screen language
Select your On-screen language: English, Spanish or French.
●
Stereo sound function
●
PLL frequency synthesized tuning
Provides free and easy channel selection and lets you tune directly to any channel using the
number and decimal point “•” keys on the Remote Control.
* 55ME314V / 50ME314V / 40ME314V / 40ME324V only.
●
Various adjustments for Picture and Sound
Customizes picture quality suitable for your room and sets your sound preference.
Note(s)
●
fun-Link via HDMI link
fun-Link allows your other HDMI link Devices to be controlled by the HDMI cable connected
to your TV.
●
If you lose the Screws, please purchase the above-mentioned Phillips head Screws at your
local store.
●
HDMI Input
●
If you need to replace these accessories, please refer to the Part Name with the illustrations
and call our toll free customer support line found on the cover of this Owner’s Manual.
●
HDMI-DVI Input
If your Video Device has a DVI Output jack, use an HDMI-DVI Conversion Cable to connect
the Unit.
When using a Universal Remote Control to operate this Unit.
●
Make sure the component code on your Universal Remote Control is set to our brand.
Refer to the instruction book accompanying your Remote Control for more details.
●
Component Video Input
●
We Do Not guarantee 100% interoperability with All Universal Remote Controls.
●
PC Input
Input from a Computer.
●
AV Input
Symbols used in this Owner’s Manual
The following is the description for the symbols used in this Owner’s
Manual. Description refers to:
Audio and Video Input from an External Device.
●
USB terminal
The Picture (JPEG) and Video (Motion JPEG) files stored on a USB Memory Stick can be
played back on this Unit.
●
Digital Audio Output
DigitalTV Operation
Digital Audio (Supporting Dolby Digital) sent to Home Theaters and other Digital Audio
systems.
●
Headphone Audio Output
Cable / NTSC (Analog)TV Operation
Headphone 3.5mm Stereo jack for personal listening.
●
If neither symbol appears, the operation is applicable to both.
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
.English
2
Stand Assembly
(55ME314V / 50ME314V)
×
3 [40ME314V / 40ME324V
×
4
[55ME314V / 50ME314V]
M4 x 0.472”(12mm)
39ME313V/F7 A]
M4 x 0.787”(20mm)
[32ME304V / 28ME304V]
M4 x 0.551”(14mm)
Note(s)
Attaching the Base
You must attach the base to the Unit to have it as a table top Unit.
Be sure the front and rear of the base match the proper direction. For
large screen TVs, at least 2 people are required for these steps.
● Make sure to use a table which can support the weight of this Unit and is larger than this
Unit.
● Make sure the table is in a stable location.
● When attaching the base, ensure that “FRONT” with “arrow” written on the bottom of
the base is downward. If it’s not downward, the 2 hooks don’t fit into the base.
● When attaching the base, ensure that All Screws are tightly fastened. If the base is not
properly attached, it could cause the Unit to fall, resulting in injuries as well as damage to
the Unit.
(55ME314V / 50ME314V)
1
● To remove the base from this Unit, unscrew the Phillips head screws in step 2. Be careful
not to drop the base when you remove it.
Mounting the Unit on your furniture
(40ME314V / 40ME324V / 32ME304V / 28ME304V / 39ME313V/F7 A)
Screw this Unit on your furniture tightly using a wood screw (Not
Supplied) in the hole at the back of the base as shown.
●
Recommended screw dimension : 3/16 x 3/4 inches (5.1 x 20 mm)
Rear of this Unit
Screw Hole
2
×
4
[55ME314V / 50ME314V]
M4 x 0.472”(12mm)
Note(s)
●
When you remove this Unit make sure to unscrew the wood screw from your Wood
Stand, Furniture and other wood item.
(40ME314V / 40ME324V / 32ME304V / 28ME304V /
39ME313V/F7 A)
1
2
1
Download from Www.Somanuals.com. All Manuals Search And Download.
9
.English
Managing cables
(55ME314V / 50ME314V / 40ME314V / 40ME324V)
Route your Antenna cable and all other cables through the cable
management tie at the back of the TV.
The holder helps keep your cables tidy and easily manageable.
Attach the cable management tie as illustrated below.
1
Pass cables through the cable management tie to avoid tangles.
2
Installing the Remote Control Batteries
Slide the battery cover off the back of the Remote Control.
1
2
Insert the 2 Supplied Batteries (AAA, 1.5V). Be sure the + and –
ends of the Batteries line up with the markings inside the case.
Slide the cover back into position.
3
Note(s)
●
Remove the Batteries if not using the Remote Control for an extended period of time.
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
10 .English
a
b
c
d
B (POWER)
Turns the TV On from Standby or Off to Standby.
Remote Control
PIC/SOUND MODE
Optimizes Picture and Sound quality.
e
a
55” - 39”
j
k
FREEZE *1
Freezes Screen image for 5 minutes.
b
0 - 9 (NUMBER keys)
Used to enter a Channel / Program number.
l
o*2
• (DOT)
:
Use with 0-9 to select Digital channels. For example,
to enter 2.1, press
d
PREV.CH
CH + / –
:
:
Returns to the previously viewed Channel.
Selects a Channel in the Memorized Channel Ring
(Low to High or High to Low).
e
f
g
h
i
SAP
f
Selects Audio mode (MONO / STEREO / SAP) / Audio language.
VOL + / –
Adjusts the Volume.
g
h
p*2
m
n
D (MUTE)
Turns the Sound On and Off.
BACK
Returns to the previous Menu operation.
i
H I J K (NAVIGATION keys) / OK
Moves the cursor, Selects the On-screen Menu items.
j
k
l
SOURCE
Selects Connected Devices.
SLEEP
Sets Sleep Timer.
PICTURE SIZE A
Adjusts the Picture size on the TV screen.
32” - 28”
j
k
m
n
o
INFO
a
Displays Information about the current program.
b
*1c
MENU
l
Opens the Main On-screen Menu.
fun-Link keys *2
d
:
H / G
Skips Backward or Forward Chapters, Titles or Tracks
on a Disc.
:
:
:
:
:
E / D
Searches Backward or Forward through the Disc.
Opens fun-Link options menu.
Stops the Disc Playback.
LINK
e
f
C
F
K
Pauses the Disc Playback.
Begins or Restarts the Disc Playback.
g
h
m
n
Note(s)
Pause may not work properly on some devices even if they are complied with fun-Link
(HDMI CEC).
●
●
i
the above functions.
p
COLOR keys *2
Use these Keys according to the directions On-screen.
*1
*2
Only Models 32ME304V / 28ME304V.
Only Models 55ME314V / 50ME314V / 40ME314V / 40ME324V /
39ME313V/F7 A.
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
11 .English
a
b
VOL J / K
Adjusts the Volume.
VOL J : Volume Down
VOL K : Volume Up
Control Panel
55ME314V / 50ME314V / 40ME314V / 40ME324V /
32ME304V / 28ME304V
In the Menu screen, moves the Cursor Left ( J ) / Right ( K ).
e
d
c
*
f
h
g
CH H / I
Selects a Channel in the Memorized Channel Ring (Low to High or
High to Low). In the Menu screen, moves the Cursor Up ( H ) /
Down ( I ).
c
d
e
f
g
h
MENU
Opens the Main On-screen Menu.
b
a
SOURCE
Selects Connected Devices.
B (POWER)
Turns the TV On and Off (Standby mode).
Remote Control Sensor
Receives IR Signal from Remote control.
Power On / Standby Indicator
(On : no light, Standby : red light)
39ME313V/F7 A
*
h
g
f
Ambient Light Sensor *
Alters the brightness of the TV screen Automatically by detecting
your room lighting level. Do Not Block this Light Sensor window to
allow proper operation.
(Only Models 55ME314V / 50ME314V / 40ME314V / 40ME324V /
39ME313V/F7 A.)
a
b
c
d
e
i
j
Component (Y/Pb/Pr) / Composite Video (VIDEO) Input jacks for
VIDEO
Composite Video Input (VIDEO) jack is a shared jack with
Component Video Input (Y) jack.
Analog Audio (L/R) Input jacks
Connect Analog Audio Signals from;
Terminals
●
HDMI-DVI / Analog Audio (L/R) jacks Signal
●
Component Video / Analog Audio (L/R) jacks Signal
m
n
●
Composite Video / Analog Audio (L/R) jacks Signal
●
PC Connection / Analog Audio (L/R) jacks Signal with Stereo Mini
3.5mm Plug Audio Cable on PC
k
l
Digital Audio Output jack
Digital Audio (S/PDIF) Output to Home Theaters and other Digital
Audio systems.
HDMI Input jack(s)
Digital Audio and Video Input from High Definition Digital Devices
such as DVD / Blu-ray Disc players, Cable / Satellite Set-top Boxes
and PC’s.
m
n
i
j
PC Input jack
o
p
VGA cable Connection for PC.
USB Terminal
Data Input from USB Memory Stick only.
Do Not Connect any Device to this terminal such as; Digital Camera,
Keyboard, Mouse, etc.
k
l
o
p
75 ohm Cable / Antenna Connection
Signal Input from an Antenna or Cable / Satellite Set-top Boxes.
Headphone Audio Output jack
Headphone 3.5mm Stereo jack for personal listening.
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
12 .English
If connecting a Set-top Box through Component Video Input
Connecting the Antenna, Cable or Satellite
Be sure your Antenna or another Device is connected properly before
plugging in the AC Power Cord.
If the TV is connected to a Cable / Satellite Set-top Box via Component
Video Input, make sure you select the correct Component Video Source
by using SOURCE.
If connecting to an Antenna through an RF cable
Any DTV Programs that are Broadcast in your area can be received for
free through an Antenna Connection.
RF cable
OUT
IN
IN
Cable
Component (Y/Pb/Pr)
Video cables
antenna
IN
Set-top Box
OUT
OUT
RF cable
IN
Audio (L/R) cables
If you connect a Set-top Box through an RF cable
If the TV is connected to a Cable / Satellite Set-top Box via a Coaxial
Connection, set the TV to channel 3/4 or the channel specified by the
service provider.
Connecting a Set-top Box, Blu-ray Disc / DVD Recorder
via Composite Connectors and Analog Audio
Do Not place your Recorder too close to the Screen because some
Recorders can be susceptible to Signals from the TV.
antenna
RF cable
Cable
OUT
Set-top Box
RF cable
IN
IN
IN
OUT
RF cable
OUT
OUT
IN
RF cable
Audio (L/R) +
Set-top Box
Video cables
If connecting a Set-top Box through an HDMI cable
OUT
IN
If the TV is connected to a Cable / Satellite Set-top Box via an HDMI
cable, make sure you select the correct Source by using SOURCE key on
TV or Remote Control.
IN
Audio (L/RR) +Video
cables
Blu-ray Disc/DVD
Recorder
Note(s)
●
●
information.
RF cable
IN
Depending on your Antenna system, you may need different types of combiners (mixers)
or separators (splitters) for HDTV Signal. The minimum RF bandpass on these Devices is
2,000MHz or 2GHz.
IN
OUT
●
●
●
●
For your safety and to avoid damage to this Unit, please unplug the RF Coaxial Cable from
the Antenna Input jack before moving the Unit.
HDMI cable
Set-top Box
If you did use an Antenna to receive Analog TV, it should also work for DTV reception.
Outdoor or attic Antennas will be more effective than a Set-top Box or inside Antenna.
To Turn On your reception source easily between Antenna and Cable, Install an Antenna
selector.
If you are not receiving a Signal from your Cable service, contact the Cable provider.
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
13 .English
No supplied cables are used with these connections:
Plugging in the AC Power Cord
●
Please purchase the Necessary Cables at your local store.
Make sure All the Necessary Connections are made before the AC Power
Cord is plugged into an AC outlet.
Before you connect the AC Power Cord:
Be sure other Devices are connected properly before plugging in the AC
Power Cord.
Caution(s)
●
Do Not connect the AC Power Cord to an AC Power Supply outside the indicated voltage
of this Unit (120V AC).
●
Connecting the AC Power Cord to a Power Supply outside of this range may result in
Unit failure, degradation or electrical shock.
Selecting your Connection quality
Note(s)
●
HDMI - Highest quality
Each time you plug in the AC Power Cord, no operations will be performed for several
seconds. This is not a malfunction.
Supports high-definition Digital signals and gives highest picture and sound
quality. Video and Audio signals are combined in one cable. You must use
HDMI for full high-definition Video and to enable fun-Link (HDMI CEC).
Note(s)
●
MAGNAVOX HDMI supports HDCP (High-bandwidth Digital Contents Protection).
HDCP is a form of Digital Rights Management that protects high definition content in Blu-
ray Discs or DVDs.
Component (Y Pb Pr) - High quality
Supports high-definition Analog signals but gives lower picture quality than
HDMI. Component (Y/Pb/Pr) Video cables combine red / green / blue
Video cables with red / white Audio (L/R) Cables. Match the cable colors
when you connect to the TV.
Composite - Basic quality
For Analog Connections. Composite Video / Audio Analog cable usually
combine a yellow Video Cable with red / white Audio (L/R) Cables. With
this Unit, yellow cable must be connected to Y (green) jack on the
Component Video Input jacks.
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
14 .English
Component Analog Video Connection
Connecting your Devices
Component Analog Video Connection offers Better Picture quality for
Video Devices connected to the Unit.
If you connect to the Unit’s Component Video (Y/Pb/Pr) Input jacks,
connect Analog Audio Cables to the Analog Audio (L/R) Input jacks.
HDMI Digital Connection
HDMI Connection offers the Highest Picture quality.
HDMI (High-Definition Multimedia Interface) transports high definition
Digital Video and multi-channel Digital Audio through a single cable.
OUT
Set-top Box
Component (Y/Pb/Pr)
or
IN
Video cables
Set-top Box
or
OUT
Blu-ray Disc/DVD
Recorder
Blu-ray Disc/DVD Player
or
IN
Audio (L/R) cables
HDMI cable
OUT
Note(s)
●
The Unit accepts 480i / 480p / 720p and 1080i of Video signals for this Connection.
HD game console
Composite Analog Video Connection
Composite Analog Video Connection offers Standard Picture quality for
Video Devices connected to the Unit.
HDMI-DVI Connection
If you connect to the Unit’s Component/Composite Video (Y/VIDEO)
Input jack (green), connect Audio Cables to the Audio (L/R) Input jacks.
When the Audio is monaural, then only connect to the Audio L Input
jack.
This Unit can be connected to your Device that has a DVI Terminal.
Use an HDMI-DVI Conversion Cable for this Connection and it requires
Audio Cable for Analog Audio signal as well.
Cable Receiver or
Audio (L/R) +
Satellite Set-top Box
OUT
OUT
Video cables
DVD Player
with the DVI Output jack
IN
IN
HDMI-DVI
OUT
conversion cable
OUT
IN
Note(s)
Audio (L//R) caables
●
●
With this Unit, yellow cable must be connected to Y (green) jack on the Component
Video Input jacks.
Whenever you connect to the Composite Video Input jack (Y/VIDEO), you must
disconnect the Component Video Input jacks (Pb and Pr). If you leave those jacks
connected, it may cause an unstable picture.
Note(s)
●
Use an HDMI cable with the HDMI logo (a certified HDMI cable). High Speed HDMI cable
is recommended for the Better compatibility.
For HDMI Connection
Digital Audio Output Connection
●
The Unit accepts 480i / 480p / 720p / 1080i, 1080p 24/30/60Hz of Video signals, 32kHz /
If you connect this Unit to an External Digital Audio Device, you can enjoy
multi-channel Audio like 5.1ch Digital Broadcasting sound.
44.1kHz and 48kHz of Audio signals.
●
This Unit accepts 5.1 channel Audio signal (Dolby Digital) and 2 channel Audio signal
(LPCM).
Use a Digital Audio Coaxial Cable to connect the Unit to External Digital
Audio Devices.
●
This Unit accepts only signals in compliance with EIA861.
For HDMI-DVI Connection
●
The Unit accepts 480i, 480p, 720p, 1080i and 1080p Video signals.
●
HDMI-DVI Connection requires separate Audio Connections as well and the Audio signals
IN
are Output as Analog (L/R) Audio.
●
DVI does not display 480i image which is not in compliance with EIA/CEA-861/861B.
Digital Auudio Cooaxiall cable
e.g.) Digital Home
OUT
Theater Amplifier
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
15 .English
Note(s)
PC Connection
●
●
Please purchase the VGA cable or HDMI-DVI Conversion Cable that has a ferrite core.
The following operations may reduce noise.
HDMI Connection
This Unit can be connected to your PC that has an HDMI terminal.
Use an HDMI cable for this Digital Connection.
–
Attach a ferrite core to the AC Power Cord of your PC.
–
Unplug the AC Power Cord and use the built-in battery of your Portable / Laptop PC.
●
Use an HDMI cable with the HDMI logo (a certified HDMI cable). High Speed HDMI cable
is recommended for the Better compatibility.
●
●
The Unit accepts 480i, 480p, 720p, 1080i and 1080p Video signals.
HDMI-DVI Connection requires separate Audio Connections as well and the Audio signals
are Output as Analog (L/R) Audio.
OUT
IN
●
DVI does not display 480i image which is not in compliance with EIA/CEA-861/861B.
HDMI cable
PC
USB Memory Stick
This unit offers easy Playback of Picture (JPEG) and Video (Motion JPEG)
files.
HDMI-DVI Connection
Insert the USB Memory Stick into the USB terminal shown below.
This Unit can be connected to your PC that has a DVI Terminal.
Use an HDMI-DVI Conversion Cable for this Video Digital Connection
and it requires Stereo mini 3.5mm Plug Audio Cable for Analog Audio
signal as well.
PC
IN
OUT
HDMI-DVI
conversion cable
OUT
IN
Stereo MMini 33.5 mm Plug
Audio cable
Note(s)
●
The Unit recognizes only a USB Memory Stick.
●
Do Not use a USB hub or an extension cable to connect an External hard disk drive to
the Unit. (Not Supported.)
VGA Connection
●
A USB Memory Stick is always inserted to this Unit directly.
This unit is equipped with a PC Input jack. If you connect this Unit to your
PC, you can use this Unit as a PC monitor.
Use a VGA cable for this Video Connection and it requires a Stereo mini
3.5mm Plug Audio Cable for Analog Audio signal as well.
●
A USB Memory Stick is Not Supplied with this Unit.
●
We Do Not guarantee that All USB Memory Sticks can be supported by this Unit.
●
Be sure to keep a backup copy of the original files on your Device before you play them
back on this Unit. We have no responsibilities for damage or loss of your stored data.
●
To protect your USB Memory Stick files from being erased place the write protect sliding
tab in the protect position.
PC
●
When you are ready to remove a USB Memory Stick, set the Unit to go into Standby
VGA cable
mode to avoid any damage to your data and the Unit.
IN
OUT
●
A USB Memory Stick that requires its own driver or the Device with a special system such
as fingerprint recognition are Not Supported.
●
This unit is not allowed to use the USB Memory Stick which requires an External Power
OUT
Supply (500mA or more).
IN
Stereo MMini 33.5 mm Plug
Audio cable
The following Video signals can be displayed:
Format
Resolution
Refresh rate
VGA
640 x 480
SVGA
XGA
800 x 600
1,024 x 768
1,280 x 768
1,360 x 768
1,920 x 1,080
60Hz
WXGA
FHD*
Other formats or non-standard signals will not be displayed correctly.
* Only Models 55ME314V / 50ME314V / 40ME314V / 40ME324V /
39ME313V/F7 A.
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
16 .English
These Operations are accessible by Remote Control.
Some may also be accessible by the Main Unit's Control Panel.
4
Use H I to select the desired Location setting, then press OK.
Home is the ENERGY STARN qualified setting.
Initial setup
Initial Setup
Retail
This section will guide you through the Unit’s Initial setting which includes
selecting a Language for your On-screen Menu and Autoprogram, which
Automatically scans and memorizes viewable channels.
Location Home is recommended for normal home use
and is ENERGY STAR qualified.
In the Retail store mode, all settings are fixed.
Home
Before you begin:
Make sure the Unit is connected to an Antenna or Cable.
1
After making All the Necessary Connections, press B to Turn On
the Unit.
●
It may take a few moments to Turn On the Unit for the first time.
Select
OK
●
Initial setup menu appears Automatically after the Unit is Turned
On.
●
Select Home, the Unit is set to maximize the energy efficiency for
home setting and it can be adjusted through a choice of Picture
and Sound quality according to your preference. Use this setting
2
Use H I to select the On-screen language from the choices
(English / Español / Français) on the right side of the TV screen, then
press OK.
●
You must set Home in step 4. Otherwise, Picture and Sound
settings you adjusted will not be memorized after the Unit goes
into Standby mode.
3
Use H I to select Antenna for TV channels or Cable for CATV
channels, then press OK.
Initial setup
●
●
When the Initial setup is completed, the Lowest Memorized
Channel with the confirmation message of the Location setting will
be displayed on the TV screen.
Make sure the antenna is connected to "ANTENNA IN"
Antenna
Cable
Skip
jack.
Select your signal source.
Select Retail, the Unit will be set up with predefined settings for
retail displays. In this setting, the Power Consumption may possibly
exceed the limited requirement limit of the ENERGY STARN
qualification.
Antenna
Cable
Or
ANTENNA IN
Back
Note(s)
●
●
If you are not receiving a signal from your Cable service, contact the Cable provider.
Select
OK
Skip
If you press B or MENU during Autoprogram, this Setup of TV channels will be Cancelled.
●
The Initial Autoprogram function can be executed for either Antenna or Cable only Once.
When you change the Connection (Antenna / Cable), select Autoprogram again.
–
When Antenna is selected, the TV detects Antenna signals. It
searches for DTV and Analog TV channels available in your area.
●
If there is no signal Input from the Antenna terminal and no operation for several seconds
after you Turn On the Unit, Helpful hints appears. Follow the instructions listed on the
TV screen.
–
When Cable is selected, the TV detects signals supplied by
Cable. It searches for DTV, Analog TV and Cable channels
available in your area.
Initial setup
●
Autoprogram will begin.
No channel is registered.
Retry
Try Autoprogram again?
Initial setup
Verify that you have a cable connected to the
Later
ANTENNA IN jack on the back of the TV, the channel
installation process searches this connection.
If you are using a cable or satellite box, please confirm
the input which you have connected to the box and
press "SOURCE" key on the remote control to select
the appropriate source input.
Please wait while the system is scanning for channels.
Auto programming may take more than 20 minutes to
complete.
0%
Digital channels
Analog channels
0 ch
0 ch
Select
OK
Skip
After an Initial Setup is completed...
Skip
●
If you want to scan the channels Automatically again.
●
You can add the desired Cable and Analog channels not memorized by
Autoprogram.
●
●
If you want to change to another Language.
If you want to change the Location setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
17 .English
4 Use your TV
Switching Channels
55ME314V / 50ME314V / 40ME314V /
40ME324V / 32ME304V / 28ME304V
39ME313V/F7 A
Switching on your TV and putting it in Standby
mode
55ME314V / 50ME314V / 40ME314V /
40ME324V / 32ME304V / 28ME304V
39ME313V/F7 A
TV
TV
Remote Control
55” - 39”
32” - 28”
TV
TV
Remote Control
To Turn the TV On from Standby or Off to Standby
●
Press B on the Side or Front panel or the Remote Control.
Note(s)
●
Energy Consumption contributes to air and water pollution. When the AC Power Cord
is plugged in, your TV consumes energy with a very low standby Power Consumption.
To select Channels by using CHI / H or CH + / –
Adjusting Volume
●
Press CH I (Down) / H (Up) on the Front panel or press CH + / –
on the Remote Control or the Side panel.
55ME314V / 50ME314V / 40ME314V /
40ME324V / 32ME304V / 28ME304V
39ME313V/F7 A
To select Channels by using the NUMBER keys
DigitalTV Operation
●
For Digital channels, press a number followed by a dot “•” and the
corresponding sub channel number.
TV
TV
Remote Control
–
When selecting Digital channel 11.1
55” - 39”
32” - 28”
Be sure to press • before entering the subchannel number.
Cable / NTSC (Analog)TV Operation
To decrease or increase Volume
–
When selecting Cable or Analog channel 11
●
Press VOL J / K on the Front panel or press VOL + / – on the Remote
Control or the Side panel.
VOL J(-) : Volume Down
VOL K(+) : Volume Up
To mute or unmute sound
Press PREV.CH to return to the previously viewed channel.
●
Press D on the Remote Control to mute the sound.
Note(s)
●
Press D again or VOL + / – to recover the original sound.
●
To select the non-memorized channels, use the NUMBER keys.
●
No signal will appear on the TV screen after the subchannel broadcast is over.
●
Audio only program message will appear on the TV screen, when you receive only a
sound signal.
Download from Www.Somanuals.com. All Manuals Search And Download.
18 .English
Watching Channels from an External Device
Switching Each Input Mode can easily switch with the Remote Control
between TV (DTV or Analog TV) and External Devices when they are
connected to the Unit.
Sleep Timer
Sleep Timer can set the Unit to go into Standby mode after an incremental
period of time.
55” - 39”
32” - 28”
Turn On the Set-top Box or the Connected Device.
1
●
The picture from the Set-top Box or the Connected Device might
appear Automatically on the TV screen.
If the picture does not appear
Press SLEEP Repeatedly to change the amount of time
(increases the time by 30 minutes up to 120 minutes).
Sleep timer 120min.
Press SLEEP Once to call up the display for checking the remaining time.
① Press SOURCE Repeatedly to select the Set-top Box or the
Connected Device and wait a few seconds between each selection
until the Picture appears.
●
To cancel Sleep Timer, press SLEEP Repeatedly until Off is displayed.
Freeze Mode
●
Pressing H reverses the direction of the Input modes.
(Only Models 32ME304V / 28ME304V.)
e.g.)
11.1
HDMI1
Source
HDMI2
HDMI3
TV
DTV / Analog TV
HDMI1
HDMI2
HDMI3
Video
PC
channel
Freeze Mode can freeze the image shown on the TV screen
Freeze
Video
or
Component
for 5 minutes.
PC
Press FREEZE to freeze the image.
●
The Sound Output will not be paused.
●
② Use the Remote Control for the Set-top Box or the Connected
To cancel Freeze Mode, press any keys except B.
Device to select Channels to view.
Switching Audio Mode
55” - 39”
32” - 28”
Changing Picture and Sound Settings
Press PIC/SOUND MODE to set your TV to a predefined Picture
and Sound setting.
1
55” - 39”
32” - 28”
DigitalTV Operation
Press SAP to display the currently selected Language
and the number of available Languages.
Press SAP Repeatedly to cycle through the available
Audio Languages.
1
2
11.1
English 1/3
2
Use H I to select one of the following settings :
Auto
picture
Note(s)
Auto sound
Description
●
●
Available Languages differ depending on the Broadcast.
Other is displayed when the Audio Language cannot be acquired or the acquired
Languages are other than English, French or Spanish.
The Customized Settings you defined
using the Picture and Sound menu
Personal
Standard
Vivid
Cable / NTSC (Analog)TV Operation
For normal TV viewing
Enhanced picture contrast, sharpness and
sound for viewing in a well-lit room
Press SAP to display the currently selected Audio mode.
1
2
While receiving an MTS broadcast, press SAP Repeatedly
to cycle through the available Audio Channels.
Brilliant picture settings and clear sound
for high action
11
Sports
Movie
SAP / STEREO
Deep picture and powerful sound settings
for a cinematic experience
e.g.) When All Audio Modes are available
SAP / STEREO
SAP / MONO
SAP / STEREO
Game
–
–
Optimized for PCs and game consoles
Stereo
SAP
Mono
Eco TV settings for low Power
Consumption
: Outputs Stereo Audio
: Outputs a Second Audio Program
: Outputs Mono Audio
Eco
Music
–
Optimized for Music Playback
Controls Picture Tone and Sets the
Anchor's Voice at a comfortable volume
level
News
–
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
19 .English
Normal
4:3
Original size.
fun-Link options
(Only Models 55ME314V / 50ME314V / 40ME314V / 40ME324V /
39ME313V/F7 A.)
Shortened horizontally.
Sidebars appear on both edges of the screen.
Vertically stretched to fill the screen.
This only crops out the top of the picture.
Movie expand
Zoom
If you have our brand products such as Blu-ray Disc player or DVD
recorder that are compatible with fun-Link functions, connect them to
this Unit via an HDMI cable so you can simply operate various items from
this Unit’s Remote Control.
Maximum size without changing its horizontal and
vertical ratio.
Horizontally stretched picture.
This crops out the left and right sides of the picture.
Before you begin:
Wide
You must set On in Device control and fun-Link
Control###Err:osd###. L【Error!】ページ
For 4:3 Video signal
Otherwise, LINK does not work even if you connected our brand devices
to this unit.
To enjoy fun-Link, verified and recommended devices are as
follows;
Normal
16:9
Movie expand
Zoom
Full can also be selected
after Wide if an HDMI
Device is selected.This
picture format similarly
displays like 16:9.
MAGNAVOX : MBP1300 / MBP5320 / MRD430B
Press LINK to display fun-Link options menu.
fun-Link options
1
Device-menu
Full
Wide
Device-contents
Device-favorite
(HDMI Device only)
Controls the menu of your connected fun-Link
device.
Original size.
Sidebars appear on both edges of the screen.
Device-menu
Normal
16:9
Controls the top menu of your DVD or Blu-ray
Discs.
Stretched horizontally to fill the screen.
Device-contents
Device-favorite
Stretched more vertically at the top of the screen.
This crops out the top of the picture.
Movie expand
Controls the pop-up menu of your Blu-ray Discs.
Maximum size that is more vertically stretched to fill
the screen.
This crops out the top and bottom of the picture.
2
Use H I or OK on this Unit’s Remote Control to operate the
desired functions for your devices.
Zoom
Wide
Note(s)
Original size and the edges stretched horizontally to
fill the screen.
●
●
●
Some of fun-Link functions may not be available depending on your fun-Link devices or
Discs.
You must connect this Unit to our brand fun-Link devices and be sure its fun-Link (HDMI
CEC) setting is also set to On.
We do Not guarantee 100% interoperability with other brands of HDMI link compliant
devices.
For PC Input signal
Normal
Full
Unscaled
Changing Picture Format
Display Modes can be Selected when your TV receives a 16:9 or 4:3 Video
Signal.
●
This Unit can also be connected to your PC that has a DVI Terminal.
Use an HDMI-DVI Conversion Cable for this Video Connection and it
requires a Stereo Mini 3.5mm Plug Audio Cable for Analog Audio signal
as well.
Three types of Display Modes can be Selected for a PC Input Signal.
Press PICTURE SIZE A Repeatedly to Switch the TV Aspect Ratio.
●
Refer to 16:9 Video Signal on this page if the PC has an HDMI Output.
Proportionately stretched picture.
Sidebars appear on both edges of the screen.
55” - 39”
32” - 28”
Normal
Full
Stretched out of proportion to fill the screen.
Original size.
Unscaled
For 16:9 Video signal
Normal
4:3
Movie expand
Full can also be selected
after Wide if an HDMI
Device is selected.This
picture format similarly
displays like Normal.
Full
Wide
Zoom
(HDMI Device only)
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
20 .English
TV Screen information
You can display the currently selected channel or other information such
as the aspect ratio on the TV screen.
In the Digital mode, the detailed broadcasting information for the current
off the air channel, such as Program title, are displayed.
Press INFO.
1
DigitalTV Operation
a
b
c
A Day of Memories
Rating information:
KABC
11.1
d
US TV
US TV
US TV
US TV
: TV-MA
: TV-14
: TV-PC
: TV-G
: X
: NC-17
: R
English
1/2
US movie
US movie
US movie
US movie
1080i
HD
16:9
e
f
Rating
CC
: PG-13
g
a
b
Program title
Broadcast station
Cable / NTSC (Analog)TV Operation
c
11
d
e
SAP / STEREO
480i
SD
4:3
CC
TV-PG DLSV
f
g
c
d
e
f
g
Channel Number
Audio Language (DTV) / Audio mode (Analog TV)
Program’s image Aspect Ratio
CC (Not available if Closed Caption is set to Off)
Child Lock rating
Press INFO to hide the information.
2
Note(s)
●
When the program guide consists of more than 4 lines, use H I to scroll to the next /
previous lines.
●
●
●
No description provided. is displayed when the program guide is not provided.
While the TV screen information is displayed, the Closed Caption function is interrupted.
In External Input mode, the following screen is displayed;
e.g.) When an External Device is connected to Video Input jack.
Video
SD
480i
4:3
TV-PG DLSV CC
●
The information display will Automatically disappear in 5 seconds.
Download from Www.Somanuals.com. All Manuals Search And Download.
21 .English
5 Making more use with your TV
2
Use H I to select the desired Menu and an item, then press OK or
use H I J K to determine the setting.
This section describes the overview of the Main Menu displayed when
you press MENU.
The Main Menu consists of the function setting items below.
Picture
Adjusting the Picture Mode or customize the Picture quality as
your preference.
Displaying the Main Menu
Press MENU to display the Main Menu.
1
Sound
Adjusting the Sound Mode, Equalizer and some other Sound
functions.
Setup
Scanning the Channels available in your area and see what the
Antenna Signal levels are.
Picture
Sound
Setup
Features
Language
USB
Auto picture
Backlight
Contrast
Brightness
Color
Tint
Personal
18
50
30
30
0
Features
Adjusting the Closed Caption, Parental Guide and some other
useful functions.
Sharpness
Advanced settings
2
Language
You can choose English, Spanish or French as your On-screen
Language.
USB
You can view Picture (JPEG) and Video (Motion JPEG) files
stored on a USB Memory Stick.
When the Setting is completed, press MENU or BACK to Exit.
3
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
22 .English
●
You can set a Particular Picture Quality using Advanced
settings.
Picture
Before you begin:
Color alignment
Noise reduction
Ambient light sensor
Normal
On
On
Picture
Sound
Setup
Otherwise, personalized Picture and Sound settings will not be
memorized after the Unit goes into Standby Mode.
1
*
Black stretch
Dynamic contrast
Gamma
Film mode
BMR 120
On
On
Gamma2
Auto
On
Features
Language
USB
1
Press MENU and use H I to select Picture, then press OK.
Picture
Sound
Setup
Auto picture
Backlight
Contrast
Personal
1
2
*
*
18
50
30
30
0
Features
Language
USB
Brightness
Color
Tint
to set the picture color temperature to
Personal (Cool, Normal or Warm)
When you adjust the following
settings, Personal picture will be set
Automatically when Location is set to
Home.
Color
temperature
mode
Sharpness
Advanced settings
2
J Cursor
Cursor K
2
Use H I J K to select the item you want to adjust, then press
OK.
to Decrease Red to Increase Red
Contrast
Red gain
Green gain
Blue gain
Contrast
to select the desired setting, then press OK.
(Personal, Standard, Vivid, Sports, Movie, Game
Color
alignment
to Decrease
Green Contrast
to Increase Green
Contrast
and Eco)
Auto picture
to Decrease Blue to Increase Blue
Contrast Contrast
to Decrease Red to Increase Red
When you adjust the following settings, Personal
picture will be set Automatically when Location
is set to Home.
Red offset
Brightness
Brightness
J Cursor
Cursor K
Green
offset
to Decrease
Green Brightness Brightness
to Increase Green
to Reduce Power
Consumption and
Reduce Backlight
Brightness
to Increase Power
Consumption and
Brightness
Backlight
to Decrease Blue to Increase Blue
Brightness
Blue offset
Brightness
Off
On
Off
to Set Noise reduction to Off
to Reduce Noise in an Image
to Set Ambient light sensor to Off
Contrast
Noise
reduction
to Decrease Contrast to Increase Contrast
to Decrease Brightness to Increase Brightness
Brightness
to Decrease Color
Intensity
to Increase Color
Intensity
Color
Ambient light
sensor *1
to Adjust Backlight for Best Picture
quality based on the incoming Video
Signal
Tint
On
to Add Red
to Soften
to Add Green
to Sharpen
Sharpness
Off
On
Off
to Set Black stretch to Off
to Enhance Black Color
to Select the desired Setting, then press OK.
(Color alignment, Noise reduction,
Ambient light sensor *1, Black stretch,
Dynamic contrast, Gamma, Film mode *1 and
BMR 120 *2)
Black stretch
Advanced settings
to Set Dynamic contrast to Off
Dynamic
contrast
to Enhance Contrast in an Image
Automatically
On
Gamma1
Gamma2
Gamma3
Off
Note(s)
to Change the Gamma setting
(changes the Brightness and Contrast
in the picture)
Gamma
●
Adjusts Backlight for the Best Picture Quality by Dynamically Adjusting the Backlight
Intensity in accordance with the Room Lighting Condition when Ambient light sensor *1
is Set to On. Please ensure the Room Lighting is Stable and the Light Sensor is Not Blocked.
to Set Film mode to Off
Film mode *1
BMR 120 *2
to Optimize the Picture recorded by
the Original film
Auto
Off
On
to Set BMR 120 to Off
to Make the Video appear smooth
*1
*2
Only Models 55ME314V / 50ME314V / 40ME314V / 40ME324V /
39ME313V/F7 A.
Only Models 55ME314V / 50ME314V / 40ME314V / 40ME324V.
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
23 .English
You can select Audio Output through a Digital Audio Output connector.
Sound
to Output Multichannel Signals
(When the Audio of the Content
is PCM, it will be Output in PCM
even if Multichannel is selected.)
Before you begin:
Multichannel
Digital output
format
Otherwise, personalized Picture and Sound settings will not be
memorized after the Unit goes into Standby Mode.
PCM
to Output PCM format.
You can set the Output mode as a default for the Sound mode (Analog
TV only).
1
Press MENU and use H I to select Sound, then press OK.
This setting is not interlocked when you change the Output mode by
Picture
Sound
Setup
Features
Language
USB
Auto sound
Equalizer
Standard
Stereo
Mono
SAP
to Output Stereo Audio
DTS TruSurround
Auto volume leveling
TV speakers
Digital output format
Primary MTS
On
Off
On
Multichannel
Stereo
Primary MTS
to Output Mono Audio
to Output Second Audio Program
2
Use H I J K to select the item you want to adjust, then press
OK.
to select the desired setting, then press OK.
(Personal, Standard, Vivid, Sports, Movie, Music
and News)
When you adjust the following settings
(Equalizer, DTS TruSurround and Auto volume
leveling), Personal sound will be set
Auto sound
Automatically when Location is set to Home.
Adjust the tonal quality for each frequency.
Cursor I
Cursor H
Equalizer
to adjust each level of tonal quality.
Press BACK to go back to the previous menu.
This selects Sound Modes for more spatial or Surround Sound
reproduction.
Off
On
to set DTS TruSurround™ to Off
DTS TruSurround
to set DTS TruSurround™ to On
This function keeps a constant loudness level between the TV
commercials and the Programs.
to Remove the Auto volume
leveling
Off
Auto volume
to Reduce Volume Differences
between the TV Commercials and
the Programs
leveling
On
You can select the Audio Output from the Unit’s speakers or not. If your
amplifier is HDMI link function compatible and connected by an HDMI
cable to this Unit, some sound operations such as volume up can be
changed by using this Unit’s Remote Control.
to Output Sound from the Unit’s
Speakers
On
No Output Sound from the Unit’s
Speakers
Off
TV speakers
to Control Audio Output from
your connected fun-Link (HDMI
CEC Link
CEC) Compliant Devices with
VOL + / – by using this Unit's
Remote Control.
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
24 .English
Setup
Autoprogram
Before you begin:
Please wait while the system is scanning for
channels.
Make sure the Unit is connected to Antenna or Cable.
Auto programming may take more than 20 minutes
to complete.
1
Press MENU and use H I to select Setup, then press OK.
75%
Picture
Sound
Setup
Autoprogram
Channel list
Add channels
Digital channels
Analog channels
10 ch
6 ch
Features
Antenna
Exit
Language
USB
●
When the Scanning and Memorizing of Available Channels is
Completed, the Lowest Memorized Channel will be Displayed.
Note(s)
●
After setting Autoprogram, using CH + / – skips unavailable channels Automatically.
If you are not receiving a signal from your Cable service, contact the Cable provider.
If you press B or MENU during Autoprogram, the Setup of TV channels will be Cancelled.
●
●
Adjust the following items.
2
●
Even if Autoprogram is completed, the channel setting will be lost if the AC Power Cord
is unplugged before the Unit goes into Standby mode by pressing B.
●
The PIN Code will be required Once you set a PIN code in the Child and Ratings Lock.
Autoprogram
●
Be sure the RF cable is correctly connected to this Unit and you are
registered with your Cable TV provider when you Install Cable channels.
1
Use H I to Select Autoprogram, then press OK.
●
Channel list
The channels selected here can be skipped when selecting the channels
using CH + / –.
If you run Autoprogram when you have Locked Channels, a
Message appears asking to enter your PIN. Enter your Child Lock
PIN in order to Complete the Installation. (Default PIN code is 0,
0, 0, 0.) You need to reset or set the Channel Lock again after the
Installation.
Those channels can still be selected with the NUMBER keys.
2
1
2
Use H I to Select an appropriate Option, then press OK.
Use H I to select Channel list, then press OK.
–
When Antenna is selected, the TV Detects Any Off-the-Air
Use H I to select the channel you want to remove, then press
OK.
Antenna Signals. It searches for ATSC (Digital) and NTSC
(Analog) Channels available in your Area.
–
When Cable is selected, the TV detects signals supplied by
Cable. It searches for DTV, Analog TV and Cable channels
available in your area.
Picture
Sound
Setup
DTV
DTV
DTV
11.1
11.2
11.3
Highlight channels for Ch Up/Down
key selection.
Features
Language
USB
Picture
Sound
Setup
Back
Antenna
Cable
Auto program will rescan all channels.
Auto programming may take more
than 20 minutes to complete.
Features
Language
USB
Select your signal source.
Antenna
Watch / Skip
Ch Select
Back
Cable
Or
●
●
●
The channel display for the removed channel darkens. You will not
be able to select the channel again using CH + / –.
ANTENNA IN
To reactivate a removed channel, use H I and press OK. The
registered channels are highlighted.
When you remove a main channel, its subchannels are removed
as well.
Note(s)
●
The channel with DTV indicated on the display is ATSC. Otherwise the channel is Analog
TV (NTSC).
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
25 .English
Features
1
Add channels
This function lets you add the off the air Analog TV or Analog Cable
channels that were not added by the Autoprogram due to reception
conditions during the Initial Setting.
Display Setup using Home Menu and use H I to select Features,
then press OK.
1
2
Use H I to select Add channels, then press OK.
Picture
Sound
Setup
Caption settings
Child lock
PC settings
Use the NUMBER keys to enter the number of the channel you
want to add, then press OK.
Features
Language
USB
fun-Link (HDMI CEC)
Location
E-sticker
Add channels
Picture
Sound
Setup
Features
Language
USB
Home
- -
For analog channels, select a channel
to be added using number keys.
For digital channels, Autoprogram
function is required.
Software upgrade
Adjust the following items.
2
Ch Change
Back
Caption settings
Closed Captions displays the Audio portion of the Program as
Superimposed Text over the Video.
Note(s)
●
●
If Setup completes successfully, Added to the channel list. is displayed.
1
Use H I to Select Caption settings, then press OK.
If External Input is used, it is not possible to register the channel and Unavailable will be
displayed on the TV screen.
●
Some channels cannot be selected by CH + / –. Use the NUMBER keys to select the
non-memorized Channel list channels.
Closed captions
Caption service
Digital caption service
Caption style
Picture
Sound
Setup
Features
Language
USB
Off
CC-1
CS-1
Antenna Confirmation
DigitalTV Operation
This function lets you check the Digital signal strength of each channel.
1
Use H I to select Antenna, then press OK.
Use the NUMBER keys or CH + / – to select the channel for which
you want to check the Digital signal strength.
2
2
Use H I J K to select the Feature you want to use, then press
OK.
Picture
Sound
Setup
Features
Language
USB
Back
You can choose the Closed Caption display.
Off
Closed Caption is not displayed.
Closed Caption is always
displayed.
On
Closed captions
Max
Current
CC w/
mute
Closed Caption is displayed when
the Sound is Off.
DigitalTV Operation
Ch Change
In addition to the basic Closed Caption, DTV has its own Closed Caption
called Digital caption service. Use this menu to change the settings for
Digital caption service.
Note(s)
Select one of these before
●
Digital caption
service
changing any other item in
Caption settings menu. Choose
If the channel is set to an Analog channel or External Input, you cannot confirm the Antenna
condition.
CS-1 to
CS-6
CS-1 under normal conditions.
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
26 .English
Cable / NTSC (Analog)TV Operation
Note(s)
●
●
Closed Caption will NOT be displayed when you are using an HDMI Connection.
The primary Closed Captions and
Digital caption service that you can switch differs depending on the broadcast description.
Caption style will not have any effect if the User setting is set to Off.
The captions do not always use correct spelling and grammar.
Text Services. The Closed
Captions or Text is Displayed in
the same Language as the
Program’s Dialog (up to 4 lines of
script on the TV Screen).
●
●
●
CC-1 and
T-1
Not all TV Programs and product commercials include Closed Caption information or All
types of the Closed Captioning. Refer to your area TV Program listings for the TV channels
and times of Closed Caption shows. The captioned programs are usually noted in the TV
listings with abbreviations such as CC.
Serve as the preferred Data
Channels. The Closed Captions or
Text is often a Secondary
Language.
●
To show the Closed Caption on your TV screen, Broadcast signal must contain the Closed
Caption data.
CC-3 and
Caption service
T-3
●
●
●
●
Captions and texts may not exactly match the TV voice.
Changing channels may delay the Closed Caption for a few seconds.
Adjusting or muting the volume may delay the Closed Caption for a few seconds.
Rarely available and Broadcasters
use them only in Special
conditions, such as when CC-1
and CC-3 or T-1 and T-3 are Not
available.
CC-2,
CC-4, T-2
and T-4
Abbreviations, symbols and other grammatical shortcuts may be used in order to keep
pace with the on-screen action. This is not a malfunction.
●
●
The caption or text characters will not be displayed while the main menu or functions
display is shown.
If a black box appears on the TV screen, this means that the Closed Caption is set to the
text mode. To clear the box, select CC-1, CC-2, CC-3, or CC-4.
●
There are 3 Display modes according to Programs:
Displays Characters on the TV screen
immediately.
●
If the Unit receives poor quality television signals (mainly when the Analog (NTSC) is
received), the captions may contain Errors or there might be no captions at all. Some
possible causes of poor quality signals are:
Paint-on
Once Characters are Stored in Memory, they are
Displayed All at Once.
–
Automobile ignition noise
Pop-on
–
Electric motor noise
–
Displays the Characters Continuously by
Scrolling (max. 4 lines).
Weak signal reception
Roll-up
–
Multiplex signal reception (ghosts or screen flutter)
–
Data dropout and Pixelation (for DTV only)
You can choose the Font (Size, Color, etc), Background and other
Characteristics of the Closed Captions Text.
●
●
The Unit retains the Closed Caption setting if the Power fails.
When the Unit receives special effects Playback signal (e.g. Search, Slow and Still) from a
VCR’s Video Output channel (ch3 or ch4), the Unit may not display the correct caption
or text.
Font style
Font size
Closed Captioning
font style, size,
color and
transparency
(opacity) can be
changed.
●
The EUT setting that satisfies § 79.102 (e) is as follows:
Font
Font color
–
Font: Mono-font
–
Character Size: Large
Font
opacity
Background
color
Background color
and transparency
(opacity) of the
displayed caption
can be switched.
Caption style
Background
Edge
Background
opacity
Edge color
Edge type
Edge color and
type of the
displayed caption
can be switched.
Picture display
So, you must bee Philip. Hi!
I’m pleased to meet you.
Font
(Font style, Font size, Font color and Font opacity)
Edge
(Edge color and Edge type)
Background
(Background color and Background opacity)
●
Review your setting choice made above by looking in the upper right
corner of the displayed setting box (not All selections show the
differences selected).
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
27 .English
Channel lock
Child and Ratings Lock
Particular Channels or External Input modes can be invisible in this
function.
You can prevent your children from watching certain Programs or certain
Channels by locking the TV Controls and by using Ratings.
3
Use H I to Select Channel lock, then press OK.
1
Use H I to select Child lock, then press OK.
4
Use H I to Select the Particular Channels or External Input, then
press OK Repeatedly to Switch between Block and View.
Picture
Sound
Setup
Caption settings
Child lock
PC settings
●
G indicates that the Channel or Input Source is Locked (Block).
●
E indicates that the Channel or Input Source is Not Locked
(View).
Features
Language
USB
fun-Link (HDMI CEC)
Location
E-sticker
Home
- -
Picture
Sound
Setup
HDMI1
HDMI2
HDMI3
Software upgrade
Features
Language
USB
Video
PC
40.1
40.2
DTV
DTV
Use the NUMBER keys to enter the 4-digit numbers for your PIN
code.
2
●
When you have not set up your PIN code, enter 0, 0, 0, 0.
●
When the PIN code is correct, Child lock menu is displayed.
See the following description for setting each item.
Picture
Channel lock
US movie ratings lock
US TV ratings lock
Canadian English rating
Canadian French rating
Region ratings lock
Clear region ratings lock
Change PIN
Sound
Setup
Features
Language
USB
Note(s)
●
When you select a rating and set it to G or E, the higher ratings will be Blocked
Automatically. The lower ratings will be available for viewing.
●
●
When you set the highest rating to E, All ratings turn to E Automatically.
To Block any inappropriate programs, set your limits in US movie ratings lock, US TV
ratings lock and Region ratings lock.
●
●
The Child Lock setting will be retained after a Power failure or after the Power is removed
for longer than 10 seconds (except the PIN code reverts to 0000).
Region ratings lock and Clear region ratings lock will be available when the Unit receives
a Digital broadcast using the New rating system.
●
●
For the United States, the Unit may download the Region Ratings Lock Table, if required.
The Canadian rating systems on this Unit are based on CEA-766-A and CRTC policy.
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
28 .English
To set the Sub ratings
Setting US Movie and TV Ratings
US Movie Ratings Lock is the Rating System created by MPAA.
US TV Ratings Lock has Controlled Access to Individual Programs based
on their Age and Content rating.
As for TV-Y7, TV-PG, TV-14 or TV-MA, you can further set the Sub
ratings to Block Specific Elements within programs. To set the Sub ratings,
follow the step below.
Use H I J K to select the desired rating, then press OK Repeatedly to
switch between G and E.
Use H I to Select US movie ratings lock or US TV ratings lock,
then press OK.
3
Use H I to Select the Desired Rating, then press OK Repeatedly
to Switch between Block and View.
4
Picture
Sound
Setup
Features
Language
USB
All
(FV)Fantasy Violence
None
●
For US TV Ratings, you can further set the Sub Ratings to Block
Specific Elements within Programs.
TV-Y
●
G indicates that the Rating is Locked (Block).
TV-Y7
●
F indicates that the Sub Rating is Locked (Block).
TV-G
●
E indicates that the Rating is Not Locked (View).
TV-PG
TV-14
US movie ratings lock
TV-MA
Picture
All
Sound
Setup
Features
Language
NR
US TV ratings
TV-Y7
Sub rating
G
(FV)Fantasy Violence
PG
TV-PG
(D)Dialog
(L)Language
(S)Sex
PG-13
USB
R
TV-14
(V)Violence
NC-17
X
(L)Language
(S)Sex
TV-MA
(V)Violence
US TV ratings lock
Note(s)
●
Blocked Sub Rating will appear beside the Main Rating category in US TV ratings lock
Menu.
Picture
Sound
All
●
●
You cannot Block a Sub Rating if the Main Rating is set to E.
None
Changing the Category to G or E automatically changes All its Sub Ratings to the same
Setup
(G or E).
TV-Y
Features
TV-Y7
Language
USB
TV-G
TV-PG
TV-14
TV-MA
US Movie
ratings
US TV
ratings
Description
All
All Ratings Locked including No Rating
No Rating
NR
None
TV-Y
–
–
Appropriate for All Children
Appropriate for All Children 7 and Older
General Audience
TV-Y7
TV-G
TV-PG
G
PG
PG-13
Parental Guidance Suggested
Unsuitable for children under 13
Unsuitable for children under 14
–
TV-14
–
Restricted under 17 Requires
Accompanying Parent or Adult Guardian
R
–
NC-17
X
–
No One under 17 Admitted
Mature Audience Only
TV-MA
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
29 .English
Canadian English or Canadian French Ratings
You can select the Rating for Canadian English or Canadian French
broadcasting.
PC settings
This function lets you adjust the PC screen position, clock and phase
during PC Input.
Use H I to Select Canadian English rating or Canadian French
rating, then press OK.
3
Use J K to adjust Clock setting to stabilize the PC screen and Phase
setting to improve the clarity of the PC screen.
Use H I to Select the Desired Rating, then press OK Repeatedly
to Switch between Block and View.
4
1
Use H I to select PC settings, then press OK.
●
G indicates that the Rating is Locked (Block).
Picture
Sound
Setup
Features
Language
USB
Auto adjustment
●
E indicates that the Rating is Not Locked (View).
Canadian
English rating French rating
Canadian
Description
Horizontal position
Vertical position
Clock
0
0
0
0
All
E
Locked All Ratings
Exempt Program
C
–
–
For All Children
Phase
C8+
For All Children 8 and Older
General Audience
G
8ans+
–
PG
Unsuitable for Ages under 8
Parental Guidance Suggested
Unsuitable for Ages under 13
Unsuitable for Ages under 14
Unsuitable for Ages under 16
Adult Audience Only
–
13ans+
–
14+
2
Use H I to select the item you want to adjust, then press OK.
–
●
The horizontal/vertical position, clock and phase of the PC screen
are Automatically adjusted.
16ans+
18ans+
–
18+
Auto adjustment
Select if you want to adjust Automatically.
Note(s)
J Cursor
Cursor K
●
Horizontal
position
The V-Chip can Block Non Rated Programs as per “CEA-608-E sec. L.3”. If the Option to
Block NR, None or E Programs are used in US movie ratings lock, US TV ratings lock,
Canadian English rating or Canadian French rating accordingly “unusual results may occur
and the Unit may not Receive Emergency Bulletins or other Types of Programming”: /
Emergency Bulletins (Such as EAS messages, Weather Warnings and Others) / Locally
originated Programming / News / Political / Public Service Announcements / Religious /
Sports / Weather.
to move PC screen
right
to move PC screen left
to move PC screen
down
Vertical position
to move PC screen up
Clock
Phase
to decrease setting
value
to increase setting
value
Change PIN
Note(s)
Although the default PIN code (0000) is supplied with the Unit, you can
set your own PIN code.
●
●
You may not obtain an appropriate screen with Auto adjustment for some signals. In this
case, please adjust the settings manually.
Properly adjust the Clock setting and then adjust the Phase setting.
Use H I to select Change PIN, then press OK.
3
4
Press the NUMBER keys to enter the New 4-digit PIN code.
●
Enter PIN code again in Confirm PIN. entry field.
Picture
Sound
Setup
Enter PIN.
Features
Language
USB
Confirm PIN.
PIN Code
Back
Note(s)
●
●
●
Make sure to enter a PIN code and the confirm PIN code must be exactly the same.
If they are different, the space is cleared to reenter the New PIN code.
When a Power failure occurs the PIN code will be erased and Unit returns to the default
PIN code (0000).
If you forget the PIN code, unplug the AC Power Cord then wait for 10 seconds to plug
the AC Power Cord in again.
The Unit will restore the PIN code to 0000 (factory default). Then repeat the Change PIN
procedure to Setup a New PIN code.
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
30 .English
Device list
fun-Link (HDMI CEC)
This function lets you see the product model number or name of
Connected Devices.
This function allows you to operate the linked functions between our
brand Devices with a fun-Link feature and this Unit connecting through
an HDMI cable. You must connect this Unit to our brand fun-Link devices
and be sure it's fun-Link (HDMI CEC) setting is also set to On.
Use H I to select the desired fun-Link devices listed on the TV screen,
then press OK.
Your connected fun-Link device will be Turned On if the device is in
Standby mode.
1
Use H I to select fun-Link (HDMI CEC), then press OK.
On
On
On
On
Picture
Sound
Setup
Features
Language
USB
fun-Link control
Auto device off
Auto TV on
Device control
Device list
Picture
Sound
Setup
Features
Language
USB
HDMI1 DVD recorder
HDMI2 Blu-ray disc player
HDMI3 Home theater system
Input Change
Refresh
Back
2
Use H I J K to select the item you want to adjust, then press
OK.
Set the fun-Link control On or Off. The following additional settings will
be grayed out when you set them to Off.
Off
Disables All fun-Link.
Selects if you have connected an
External Device that is compatible
with the fun-Link function.
fun-Link control
On
You can set your connected fun-Link device to Turn Off by interlocking
from this Unit’s Power.
Your connected fun-Link device
stays On even if the Unit goes into
Standby mode.
Off
On
Auto device off
Your connected fun-Link device
Turns Off Automatically when the
Unit goes into Standby mode.
This Unit will Turn On when the Power On Signal is sent from your
connected fun-Link device.
This Unit stays in Standby mode
even if you Turn On your
connected fun-Link device.
Off
On
Auto TV on
This Unit Turns On Automatically
when you Turn On your
connected fun-Link device.
You can operate some functions such as Disc Playback or call up the menu
of the connected devices, by using this Unit’s Remote Control.
(Only Models 55ME314V / 50ME314V / 40ME314V / 40ME324V /
39ME313V/F7 A.)
Off
Disables the device control.
PLAY K / STOP C / FWD D /
REV E / SKIP G / SKIP H /
PAUSE F / LINK / HIJ K /
OK / BACK / the NUMBER
buttons / RED / GREEN / BLUE /
YELLOW can be used to control
your connected fun-Link devices
by this unit’s remote control.
Device control
On
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
31 .English
Language
1
Setting your Location to Home
You can set the Location of your TV to Home or Retail. Choosing Home
gives you full flexibility to change predefined settings for Picture and
Sound.
Press MENU and use H I to select Language, then press OK.
Picture
Sound
Setup
Features
Language
USB
1
Use H I to Select Location, then press OK.
Select your menu language.
English
Picture
Sound
Setup
Caption settings
Child lock
PC settings
Seleccione el idioma para el menú.
Español
Français
Sélectionnez la langue du menu.
Features
Language
USB
fun-Link (HDMI CEC)
Location
E-sticker
Home
- -
Software upgrade
2
Use H I to select English, Español or Français, then press OK.
Note(s)
●
If you need the English menu instead of the Spanish or French menu’s, press MENU.
Use H I to select Idioma or Langue, then press OK.
Use H I to select English then press OK.
2
Use H I to select Home or Retail, then press OK.
The Unit will be set up with predefined settings
Press MENU to Exit the Main menu.
for retail displays. In this setting, the Power
Consumption may possibly exceed the limit
requirement of the ENERGY STARN
qualification.
Retail
This setting is ENERGY STARN qualified.
The Unit is set to maximize the energy efficiency
for Home setting and it can be adjusted through
a choice of Picture and Sound quality selections
according to your preference.
Home
Note(s)
●
You must set Home in the Menu. Otherwise, personalized Picture and Sound Settings will
Not Be Memorized after the Unit goes into Standby Mode.
E-sticker
When you set Location to Retail store, E-sticker (Electronic Sticker) is
displayed. E-sticker can be Turned Off using procedure below.
1
Use H I to select E-sticker, then press OK.
2
Use H I to select Off, then press OK.
Off
Top
You can Turn Off E-sticker.
E-sticker is displayed on top of the TV screen.
E-sticker is displayed on bottom of the TV screen.
Bottom
Note(s)
●
If you set Location to Home, E-sticker will not be displayed.
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
32 .English
Picture (JPEG)
USB
Use H I to select the desired file, then press OK.
1
Your TV is fitted with a USB Connection that enables you to view JPEG
photos or watch Motion JPEG files stored on a USB Memory Stick.
Picture
Image1.jpg
Picture
Connect the USB Memory Stick to the USB terminal on the side of
your TV.
1
Go to root folder
Image1.jpg
Image2.jpg
Image3.jpg
Image4.jpg
Image5.jpg
2
Press [Home2] (Home) and use H I to select USB, then press
OK.
●
The Highlighted Text will move to Start now, then press OK again.
Image1.jpg
1024:768
Start now
Picture
Sound
Setup
2009/04/02 17:42:06
1
2
3
4
Thumbnails
Press "OK" key to play/pause.
This menu allows you to enjoy your
pictures and videos via your USB
device.
●
To toggle between List and Thumbnails press the NUMBER 2
Features
Language
USB
key each time.
●
●
The unit goes to the Slide show Automatically.
To Pause / Play the Slide show, press OK.
Use the NUMBER keys (1 through 4) to see the file details (
)
1
or change the following settings (
~
).
2
4
See the description in table below.
Item
Detail
Press 1 to display file details below.
Name, Album, Date, Size and Next.
Press 1 again to remove file details.
1
3
Use H I to Select the Picture or Video, then press OK.
More Detail
●
These Recorded Files must meet Specifications shown below:
4
Press 4 or OK to start the Slide show.
While the Slide show is on, the following 2 settings will be displayed.
Start show
Picture (JPEG)
Upper limit 24M pixel
Press 2, then use H I to select the transition mode choosing from;
None, Dissolve, Wipe right, Wipe left, Wipe up, Wipe down, Box
in and Box out.
Size
320 x 240 (QVGA)
2
Transitions
Frame rate 30fps
Video
(Motion JPEG)
3
Press 3, then use H I to change the display time choosing from; Short,
Medium and Long.
Sampling frequency
Slide time
Audio type LPCM (32 kHz, 44.1 kHz or 48 kHz)
Quantization bit rate (16 bit)
4
Press 4 or OK to stop the Slide show.
While the Slide show is Off, the following 2 settings will be displayed.
Stop show
Note(s)
2
Every press on 2 will turn the picture clockwise by 90 degrees.
●
Up to 2GB (FAT16) or 8GB (FAT32) capacity can be supported.
Up to 10,000 files or 1,000 folders with 19 hierarchies can be recognized.
Up to 255 English characters can be recognized.
Rotate
●
●
●
●
●
●
●
3
Press 3, then use H I to select the zoom factor (1x, 2x or 4x). Press
OK to set the zoom factor.
Zoom
This unit does Not Support MTP (Media Transfer Protocol).
This unit supports FAT16 and FAT32 file systems.
If the file is Not Supported, an Error message appears.
Video (Motion JPEG)
When the USB Memory Stick is not recognized, try reconnecting it again.
We cannot be held responsible if your USB Memory Stick is Not Supported, nor will we
accept any liability for damage or loss of stored data.
Use H I to select the desired file, then press OK.
1
●
●
To protect your USB Memory Stick files from being erased place the write protect sliding
tab in the protect position.
Video
Video
MOVIE1.avi
Be sure to keep a backup copy of the original files on your device before you play them
back on this Unit.
Title:
MOVIE1.avi
Go to root folder
MOVIE1.avi
MOVIE2.avi
MOVIE3.avi
MOVIE4.avi
MOVIE5.avi
●
●
Director:
Date:
This unit does not recognize USB Memory Stick that requires a special driver.
2009/04/02
00:06:37
This unit is not allowed to use the USB Memory Stick which requires an External Power
Supply (500mA or more).
Duration:
●
A file name exceeding 128 characters or contains a dot character is Not Supported on
this TV.
●
●
Progressive JPEG files are Not Supported.
Only a Motion JPEG file with an “.avi” extension is supported. An extension “.mov” is Not
Supported.
1
2
3
4
●
During Motion JPEG Playback, “Pause”, “Forward” and “Reverse” Do Not Work on this
Unit.
Supported format: motion jpeg, 320 x 240, 30FPS
●
●
To stop Playback and return to the file list, press BACK, OK or
CH +.
Press CH - to play back from the beginning.
Item
Detail
Press 1 to display file details below.
Title:, Director:, Date: and Duration:.
Press 1 again to remove file details.
1
More Detail
Download from Www.Somanuals.com. All Manuals Search And Download.
33 .English
6 Upgrade your TV Software
Downloading the Software
Find information and Software related to your TV and Download the
Latest Software Upgrade file to your PC.
MAGNAVOX continuously tries to improve its products and we strongly
recommend that you Upgrade the TV Software when Upgrades are
available.
On your PC, open a web browser and go to
1
Enter the model number in the “Type the Model Number...” field.
2
3
New Software can be Downloaded from our website at
using the model number of your TV to find information.
Click the desired Software to be Downloaded.
●
Decompress the ZIP-file.
Copy the Upgrade file to the Empty root directory on the clean
formatted USB Memory Stick.
4
Checking your Current Software version
1
2
Press MENU and use H I to select Features, then press OK.
Starting the Software Upgrade
Use H I to select Software upgrade, then press OK.
Warning
●
Picture
Sound
Setup
Current software info
Upgrade
When the Software Upgrade is running, don’t press any keys.
●
Do Not remove the USB Memory Stick during the Software Upgrade.
●
If an Error occurs during the Upgrade, retry the procedure or for further assistance, please
contact the Call Center.
Features
Language
USB
Connect your USB Memory Stick with the Upgrade file to the USB
Service Port on the side of your TV. Use only the Unit's Front Panel
Keys to enter the following Instruction Steps 2 to 6.
1
3
Use H I to select Current software info, then press OK.
●
The version and a description of the Current Software is displayed.
Back
Picture
Sound
Setup
2
Press MENU and use H I to select Features, then press OK.
Release Version:
XXXXXXX_XX_XX_XXXX_XX
3
4
5
Use H I to select Software upgrade, then press OK.
Features
Language
USB
Use H I to select Upgrade, then press OK.
Read the On-screen instructions and confirm that you want to
continue with the Installation.
Start now
Picture
Sound
Setup
Would you like to upgrade the
software?
Upgrading the Software
You can Upgrade the Software by using a USB Memory Stick.
Features
Language
USB
Preparing for the Software Upgrade
You require the following equipment :
●
A PC with web browsing capability.
●
An archive utility that supports the ZIP-format (e.g. WinZip for
6
When the Software Upgrade is completed, press B to set the Unit
into Standby mode, then remove the USB Memory Stick and then
press B again to Turn the Unit back On.
Windows or Stuffit for Mac OS).
●
A Blank empty clean formatted USB Memory Stick.
Note(s)
●
The TV starts up with the New Software.
For further assistance, please contact the Call Center.
●
Only FAT / DOS-formatted portable memory is supported.
●
Use only Software Upgrades that can be found on the MAGNAVOX website.
Download from Www.Somanuals.com. All Manuals Search And Download.
34 .English
7 Useful tips
FAQ
Question
Answer
Check the Antenna or Cable Connection to the Main Unit.
●
●
●
●
●
Check the Batteries on the Remote Control.
Re-insert the Batteries with their Polarities (+/–) as indicated.
Check if there is an obstacle between the infrared sensor window and the Remote Control.
My Remote Control does
not work.
What should I do?
If okay, then possible Infrared Sensor trouble.
●
●
●
Aim the Remote Control directly at the infrared sensor window on the front of the Unit.
Reduce the distance to the Unit.
When there is an infrared-equipped device such as PC near this Unit, it may interrupt the Remote Control signal on this
Unit. Move the infrared-equipped device away from this Unit, change the angle of the Device's infrared sensor or Turn
Off the infrared communication function.
How come the Initial Setup
appears every time I Turn
On this Unit?
●
●
Connect the RF Coaxial Cable directly to this Unit and run the Initial Setup.
Make sure to complete the Initial Setup before the Unit goes into Standby mode.
●
●
Autoprogram must be completed when you Set Up the Unit for the First time or Move it to a location where previously
unavailable channels are broadcast.
●
●
The selected channel may not be broadcasting.
Why can I not watch some
RF signal TV Programs?
When Autoprogram is interrupted and not completed, some channels will not be received. Make sure to complete the
●
●
The Unit requires some kind of Antenna Input. An indoor Antenna (Digital or VHF / UHF), an External Antenna (Digital
or VHF / UHF) or an RF Coaxial Cable from your wall Cable / Satellite Set-top Box needs to be plugged into the Unit.
●
Check if the correct Input mode is selected by pressing SOURCE or using CH + / –. Refer to Watching Channels from
How come there is no
image from the Connected
External Devices?
●
●
Check the Antenna, Cable or other Input Connection to the Unit.
When using the Component Video Connection check that the Green (Y), Blue (Pb/Cb) and Red (Pr/Cr) connectors
are connected to their corresponding colored jacks on the Unit.
●
●
When I enter a channel
number, why does it change
Automatically?
Many Digital channels have alternate channel numbers. The Unit changes the numbers Automatically to the ones signifying
the Broadcasting Station's channel number. These basic numbers used for the previous Analog Broadcasts. (e.g., Input
Digital ch# 30 Automatically changes to Digital ch# 8.1)
Why are captions not
displayed Entirely?
Or why are captions
delayed behind the dialog?
Closed Captions that are delayed a few seconds behind the actual dialog are common for Live broadcasts. Most captioning
production companies can display a dialog to maximum of 220 words per minute. If a dialog exceeds that rate, selective
editing is used to insure that the Closed Captions remain up-to date with the current TV screen dialog.
●
●
How can I set the clock?
There is No clock function on this Unit.
My PIN code no longer
works, how can I change the
Child Lock setting?
If a Power failure occurs for longer than 10 seconds the child lock setting is retained, but the PIN code is reset to the
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
35 .English
Troubleshooting
If the Unit does not perform properly when operated as instructed in this Owner’s Manual,
check the following Troubleshooting Tips and All Connections Once before calling for Service.
●
Make sure that the selected Input mode is connected to the working Input
jack.
Check if your computer is NOT in sleep mode when the Input mode of this
Unit is in PC mode. Tap any key on the keyboard to wake up your computer.
Make sure that the sound is not muted. Press D so that the volume bar and
current volume level will appear on the TV screen.
Power
No Power
●
●
●
Make sure the AC Power Cord is plugged in.
●
Make sure that the AC outlet supplies the proper voltage, plug another
electrical appliance into the AC outlet to ensure that the AC outlet operates
normally.
If a Power Failure occurs, Unplug the AC Power Cord for 1 minute to allow
the Unit to Reset Itself.
●
Make sure that the volume is NOT set to 0 or C. If so, use VOL + / – to
adjust to the desired volume.
●
Adjusted Picture or Sound settings are not effective every time the Unit is
Remote
Control keys do not work.
turned On.
●
●
Do NOT press more than one key at the same time.
Ensure that no keys on the Remote Control are depressed and move freely.
adjusted will not be memorized after the Unit goes into Standby Mode.)
You see a Distorted Picture or Hear an Unusual Sound. (Analog TV -
NTSC signal)
●
Universal Remote Control does not work properly.
●
Refer to the user manual of the Universal Remote Control for the
●
You may be getting interference from electrical appliances, automobiles,
MAGNAVOX code.
motorcycles or fluorescent lights.
Try moving the Unit to another Location to see if this is the Cause of the
●
Picture
Problem.
Power is On but No Screen Image.
Check whether the Connection for the Antenna, Cable or Satellite Set-top
●
Ghosts, lines or streaks in picture. (Analog TV- NTSC signal)
Electrical interference from nearby appliances may affect picture quality.
View other TV channels. The problem might be limited to the Broadcasting
Station or Weak Signal Strength, if DTV channel check signal strength.
Picture Poor, Sound Intermittent or No Sound
View other TV channels. The problem might be limited to the Broadcasting
Station or Weak Signal Strength, if DTV channel check signal strength.
●
Box is Connected Correctly.
Check whether All the Cables to the Unit are connected to the correct Output
●
●
Jack on your separate Device like Blu-ray Disc / DVD Recorder.
Make sure that the selected Input mode is connected to the working Input
●
jack.
●
Check if your computer is NOT in Sleep Mode when the Input Mode on this
●
Unit is in PC mode. Tap any Key on the Computer Keyboard to Wake it up.
No Color
●
View other TV channels. The problem might be limited to the broadcasting
Screen
station.
●
You Switch to a different Input and the Screen Size changes.
This Unit will Memorize the Viewing Mode from the last time you used those
Particular Input Modes.
The Display image does not cover the Entire Screen.
If you are using the Unit as a PC Monitor, make sure that Horizontal
position and Vertical position in PC settings are set correctly.
If you are watching TV or using the Composite Video, Component Video or
HDMI with 480i Input, press PICTURE SIZE A Repeatedly to Switch to
various Screen Modes.
●
Picture Poor
●
For the Best Picture Quality, watch “High Definition” wide screen Programs.
●
●
If the HD content is Not available, watch “Standard Definition” Programs
instead.
●
You see Pixelation on the Screen.
●
When the capabilities of the Unit exceed the capabilities of the Digital
Broadcasting, the signal will be increased to match the capabilities of the
Display on the Unit. This may cause Pixelation, Noise or Trash.
Unusual picture appears and the TV does Not Operate.
Different color marks on the TV screen
View other TV channels. The problem might be limited to the broadcasting
station, missing data or pixelation due to weak signal strength.
●
●
Press the Power key first. If it does not solve the problem, then press the keys
on the Remote Control in the order shown below to change the Unit to the
Live Mode.
SLEEP L PICTURE SIZE A L K L H L I L B
Closed Captions
Closed Captions are displayed as a white box. No Closed Captions are
displayed in the Closed Captions-Supported Program.
Sound
●
Interference from buildings or weather conditions may cause captioning to be
No sound, distorted sound or incorrect Audio Sound is heard when using the
HDMI-DVI Connections.
Make sure that the Analog Audio signals from the HDMI-DVI Device are
incomplete if watching Analog TV signals.
Broadcasting Station may shorten the program to insert advertisements.
The Closed Captions Decoder cannot read the information of a shortened
program.
Black Box is displayed on the TV Screen.
The Text mode is selected. For Closed Captions, select CC-1, CC-2, CC-3
Cancel the Parental lock or change the control level.
●
●
●
connected to the Analog Audio (L/R) Input jacks.
When using Component Analog Video, Composite Analog Video or PC VGA
●
●
Video make sure that the Analog Audio (L/R) connectors are mounted into
the Audio (L/R) Input jacks.
●
Sound Intermittent or No Sound.
Check if the Audio Cable is connected into the Unit correctly.
You Switch to a Different Input and the Volume Changes.
Refer to Parental Setting L p. 0
Check the PARENTAL setting. Refer to L p. 0
Enter the default code “4737”, then your forgotten password will be cleared.
Refer to Parental Setting L p. 0
●
●
●
●
This Unit will Memorize the Volume Level from the last time you adjusted it.
If the Volume of the Sound from another Device is Higher or Lower, then the
●
Loudness will Change.
Note(s)
●
●
The LCD screen is manufactured to provide many years of useful life.
Occasionally a few non active pixels may appear as a fixed point of blue, green
or red.
This is Not to be considered a Defect in the LCD screen.
Some Functions are Not available in Specific Modes, but this is Not a
Malfunction. Read the Description in this Owner’s Manual for more Details
on Correct Operations of this Unit.
Picture & Sound
No Picture or Sound
●
Check if the Power is On.
Check whether All the cables to the Unit are connected to the correct Output
jack of your device like Blu-ray / DVD Recorder.
View other TV channels. The problem might be limited to the Broadcasting
●
●
●
Station or Weak Signal Strength, if DTV channel check signal strength.
Unplug the AC Power Cord and wait for about 1 minute, then Plug the AC
●
Power Cord and turn On the Unit again.
Check whether the Connection of the Antenna or Cable / Satellite Set-top
●
Box is connected correctly.
Continued on next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
36 .English
8 Information
Glossary
Maintenance
Analog TV (NTSC)
Cabinet Cleaning
Acronym that stands for National Television Systems Committee and the
name of Analog broadcasting standards.
Off the air Analog TV signals are no longer being sent by major
broadcasting stations in the USA.
●
Wipe the front panel and other exterior surfaces of the Unit with a soft
cloth.
●
Never use a solvent or alcohol. Do Not spray insecticide liquid near the
Unit. Such chemicals may cause damage and discoloration to the
exposed surfaces.
Aspect ratio
The width of a TV screen relative to its height. Conventional TVs are 4:3
(in other words, the TV screen is almost square); widescreen models are
16:9 (the TV screen is almost twice as wide as its height).
Panel Cleaning
Wipe the panel of the Unit with a soft cloth. Before cleaning the panel,
disconnect the AC Power Cord.
CEC (Consumer Electronics Control)
Servicing
This allows you to operate the linked functions between our brand
devices with CEC feature and this Unit. We Do Not guarantee 100%
interoperability with other brands of CEC compliant devices.
Should your Unit become inoperative, Do Not try to correct the problem
yourself. There are no user serviceable parts inside. Call our toll free
customer support line found on the cover of this Owner’s Manual to
locate an Authorized Service Center.
Component Video
This is a Video signal format that conveys each of 3 principal colors of light
(red, blue and green) through different signal lines. This allows the viewers
to experience picture colors as original as it is. There are several signal
formats, including Y / Pb / Pr and Y / Cb / Cr.
IR Signal Check
If the Remote Control is not working properly, you can use a Digital or
Cell Phone Camera to see if it is sending out an infrared signal.
e.g.) With a Digital Camera:
Dolby Digital
Point the Digital Camera towards the
Remote Control infrared diode at the front
of the Remote Control. Press any key on the
Remote Control and look at the Camera
Display. If an infrared pulsating light appears
on the Display, the Remote Control is
sending out an IR signal.
The system developed by Dolby Laboratories to compress Digital sound.
It offers Stereo Sound (2ch) or multi-channel Audio.
DTV (ATSC)
Abbreviation that stands for Advanced Television Systems Committee
and the name of the Digital broadcasting standards.
E-sticker
Note: Some Cameras have an IR Filter and will not Display the IR signal.
E-sticker is showing set features, technical information, etc on this TV set
that is displayed on the TV screen mainly used by TV retailers. Previously
the information was on a printed sticker that was put on the display.
HDMI (High-Definition Multimedia Interface)
Interface that supports All uncompressed, Digital Audio / Video formats
including Set-top Box, Blu-ray / DVD Recorder or Digital television, over
a single cable.
HDTV (High Definition TV)
Ultimate Digital format that produces high resolution and high picture
quality.
PIN code
A stored 4-digit number that allows access to Parental control features.
SAP (Secondary Audio Program)
Second-Audio channel delivered separately from the Main-Audio channel.
This Audio channel is used as an alternate in bilingual broadcasting.
SDTV (Standard Definition TV)
Standard Digital format that is similar to the Analog TV picture quality.
Download from Www.Somanuals.com. All Manuals Search And Download.
37 .English
9 Specifications
Model #
55ME314V
50ME314V
40ME314V
40ME324V 39ME313V/F7 A 32ME304V
28ME304V
Picture
WXGA (1366 x 768 pixels
60Hz)
Type
FHD (1920 x 1080 pixels 60Hz)
16:9
Aspect Ratio
Viewing Angles
178° (V) by
176° (V) by 176° (H)
178° (H)
178° (V) by 178° (H)
Built-in Digital / Analog Tuner
ATSC (Digital) / NTSC (Analog)
Sound
Mono / Stereo
Mono, Stereo, DTS TruSurround™
Power Output (RMS watts)
Equalizer
10W x 2
5 Band
8W x 2
Ease of Use
SD (4:3 Source)
: Normal / 16:9 / Movie expand / Zoom / Wide
HD (16:9 Source)
HDMI AV (4:3 Source)
HDMI AV (16:9 Source)
PC Source
: Normal / 4:3 / Movie expand / Zoom / Wide
: Normal / 16:9 / Movie expand / Zoom / Wide / Full
: Normal / 4:3 / Movie expand / Zoom / Wide / Full
: Normal / Full / Unscaled
(Refer to HDMI AV (16:9 Source) above if PC has HDMI Output.)
Picture Format
Photo Slide Show
Video Playback
Channel
JPEG Files Only
Only Motion JPEG 320 x 240, 30 fps with file extension "avi" will Playback.
Terrestrial DTV (ATSC)
: VHF: 2~13
UHF: 14~69 (Each Channel has e.g. 2.1~2.9, 3.1~3.9, etc)
Channel Coverage
Terrestrial Analog (NTSC) : VHF: 2~13
UHF: 14~69
2~13, A~W
CATV (Analog NTSC)
Tuning System
W+1~W+94 (Analog W+1~W+84), A-5~A-1, 5A
Channel Frequency Synthesized Tuning System
Direct Access Number Keyboard,
Programmable Scan, Channel +(up) / −(down) and PREV. CH (Previous Channel)
Channel Access
Connectivity
Component Video Input
(Y/Pb/Pr)
1
Supporting Video Signals : 480i/p, 720p, 1080i @60Hz
Composite Video Input
(Shared Y Green Terminal with
Component Video)
1
3
Supporting Video Signals : 480i/p, 720p, 1080i @60Hz, 1080p @24/30/60Hz
HDMI Input
PC-Input Signal up to
WXGA (1360 x 768)
PC-Input Signal up to FHD (1920 x 1080)
Analog Audio L/R Input
1
PC Input
USB
via VGA, HDMI and HDMI-DVI + Analog Audio L/R
1
1
Digital Audio Output
Supporting Dolby Digital
1
Headphone Output
1/8 inch (3.5mm)
Power
Power Requirements
Temperature
120V~ +/− 10%, 60Hz +/− 0.5%
41 °F (5 °C) to 104 °F (40 °C)
Operating Temperature
●
Specifications are Subject to Change without Prior Notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
38 .English
10 Warranty
LIMITED WARRANTY
ONE (1) YEAR PARTS AND LABOR
WARRANTY COVERAGE:
This warranty does not apply (a) to damage caused by accident,
abuse, misuse, neglect, misapplication, or non-supplied product,
(b) to damage caused by service performed by anyone other than
company approved Authorized Service Location, (c) to a product
or a part that has been modified without written company
permission, or (d) if any serial number has been removed or
defaced, or (e) product, accessories or consumables sold “AS IS”
without warranty of any kind by including refurbished product
sold “AS IS” by some retailers.
This warranty obligation is limited to the terms as set forth
below.
WHO IS COVERED:
This product warranty is issued to the original purchaser or the
person receiving the product as a gift against defects in materials
and workmanship as based on the date of original purchase
(“Warranty Period”) from an Authorized Dealer. The original
sales receipt showing the product name and the purchase date
from an authorized retailer is considered such proof.
This Limited Warranty does not cover:
•
•
Shipping costs for returning defective product.
WHAT IS COVERED:
Labor charges for installation or setup of the product, adjustment
of customer controls on the product, and installation or repair of
antenna/signal source systems outside of the product.
Product repair and/or part replacement because of improper
installation or maintenance, connections to improper voltage
supply, power line surge, lightning damage, retained images or
screen markings resulting from viewing fixed stationary
content for extended periods, product cosmetic appearance
items due to normal wear and tear, unauthorized repair or
other cause not within the control of the company.
Damage or claims for products not being available for use, or
for lost data or lost software.
This warranty covers new products if a defect in material or
workmanship occurs and a valid claim is received within the
Warranty Period. At its option, the company will either (1) repair
the product at no charge, using new or refurbished replacement
parts, or (2) exchange the product with a new or refurbished
product at company’s option.
•
Replacement products or parts provided under this warranty are
covered against defects in materials and workmanship from the
date of the replacement or repair for ninety (90) days or for the
remaining portion of the original product’s warranty, whichever
provides longer coverage for you. When a product or part is
exchanged, any replacement item becomes your property and the
replaced item becomes company property. When a refund is
given, your product becomes company property.
•
•
•
Damage from mishandled shipments or transit accidents when
returning product.
A product that requires modification or adaptation to enable it
to operate in any country other than the country for which it
was designed, manufactured, approved and/or authorized, or
repair of products damaged by these modifications.
A product used for commercial or institutional purposes
(including but not limited to rental purposes).
Note: Any product sold and identified as refurbished or renewed
carries a ninety (90) day limited warranty.
Replacement product can only be sent if all warranty
requirements are met. Failure to follow all requirements can
result in delay.
•
•
•
Product lost in shipment and no signature verification receipt
can be provided.
Failure to operate per Owner’s Manual.
WHAT IS NOT COVERED - EXCLUSIONS AND
LIMITATIONS:
This Limited Warranty applies only to new company
manufactured products that can be identified by the trademark,
trade name, or logo affixed to it. This Limited Warranty does not
apply to any hardware product or any software, even if packaged
or sold with the product, as manufacturers, suppliers, or
publishers may provide a separate warranty for their own
products packaged with the bundled product.
TO OBTAIN ASSISTANCE…
Contact the Customer Care Center at:
1 866 341 3738
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS THE EXCLUSIVE REMEDY FOR THE
CONSUMER, WITH THE ISSUING COMPANY NOT LIABLE
FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY
ON THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED
BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO
THE DURATION OF THIS WARRANTY.
The company is not liable for any damage to or loss of any
programs, data, or other information stored on any media
contained within the product, or other additional product or part
not covered by this warranty. Recovery or reinstallation of
programs, data or other information is not covered under this
Limited Warranty.
Some states do not allow the exclusions or limitation of incidental
or consequential damages, or allow limitations on how long an
implied warranty lasts, so the above limitations or exclusions may
not apply to you.
This warranty gives you specific legal rights. You may have other rights which vary from state/province to state/province.
FUNAI CORPORATION, Inc. 19900 Van Ness Avenue, Torrance, CA 90501
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNAI CORPORATION, Inc.
19900 Van Ness Avenue, Torrance, CA 90501
A4GR1UH / A4GU6UH / A4GP1UT / A4G21UH / A4GF1UT / A4GFAUT / A4GFBUT / A4GS1UT / A4AT1UT
★★★★
Download from Www.Somanuals.com. All Manuals Search And Download.
|