Magnavox Flat Panel Television 19MF330B F7 User Manual

Owner’s manual

Manuel du propriétaire

Manual del propietario

22MF330B

19MF330B

LCD TV

1-866-341-3738

MODEL NUMBER

SERIAL NUMBER

Download from Www.Somanuals.com. All Manuals Search And Download.

English

IMPORTANT SAFETY INSTRUCTIONS

Read before operating equipment

1. Read these instructions.

2. Keep these instructions.

16. Tilt/Stability - All televisions must comply with recommended

international global safety standards for tilt

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

and stability properties of its cabinet design.

• Do not compromise these design standards by applying

excessive pull force to the front, or top, of the cabinet

which could ultimately overturn the product.

• Also, do not endanger yourself, or children, by placing

electronic equipment/toys on the top of the cabinet. Such

items could unsuspectingly fall from the top of the set and

cause product damage and/or personal injury.

17. Wall or Ceiling Mounting -The appliance should be

mounted to a wall or ceiling only as recommended by the

manufacturer.

18. Power Lines - An outdoor antenna should be located

away from power lines.

19. Outdoor Antenna Grounding - If an outside antenna

is connected to the receiver, be sure the antenna system is

grounded so as to provide some protection against voltage

surges and built up static charges.

7. Do not block any of the ventilation openings.

Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliﬁers)

that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug.A polarized plug has two blades with

one wider than the other.A grounding type plug has two

blades and third grounding prong.The wide blade or third

prong are provided for your safety.When the provided

plug does not ﬁt into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the

manufacturer.

Section 810 of the National Electric Code,ANSI/NFPA

No. 70-1984, provides information with respect to proper

grounding of the mast and supporting structure, ground-

ing of the lead-in wire to an antenna discharge unit, size of

grounding connectors, location of antenna-discharge unit,

connection to grounding electrodes, and requirements for

the grounding electrode. See Figure below.

12.

Use only with a cart, stand, tripod, bracket, or table

speciﬁed by the manufacturer, or sold with the appara-

tus.When a cart is used, use caution when moving the

cart/apparatus combination to avoid injury from tip-over.

20. Object and Liquid Entry - Care should be taken so

that objects do not fall and liquids are not spilled into the

enclosure through openings.

13. Unplug this apparatus during lightning storms or when un-

used for long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into apparatus, the appara-

tus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

21. Battery Usage CAUTION -To prevent battery

leakage that may result in bodily injury, property damage,

or damage to the unit:

• Install all batteries correctly, with + and - aligned as

marked on the unit.

• Do not mix batteries (old and new or carbon and

alkaline, etc.).

• Remove batteries when the unit is not used for a long

time.

15. Damage Requiring Service -The appliance should be

serviced by qualiﬁed service personnel when:

A. The power supply cord or the plug has been damaged;

B. Objects have fallen, or liquid has been spilled into the

appliance;

C. The appliance has been exposed to rain

D. The appliance does not appear to operate normally or

exhibits a marked change in performance;

E. The appliance has been dropped, or the enclosure damaged.

Note to the CATV system installer :This reminder is provided to call the CATV system installer’s attention to Article

820-40 of the NEC that provides guidelines for proper grounding and, in particular, speciﬁes that the cable ground shall

be connected to the grounding system of the building, as close to the point of cable entry as practical.

Example of Antenna Grounding as

per NEC - National Electric Code

GROUND CLAMP

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

ELECTRIC SERVICE EQUIPMENT

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

Download from Www.Somanuals.com. All Manuals Search And Download.

FCC WARNING

This apparatus may generate or use radio frequency energy. Changes or modifications to this apparatus may cause harmful interference

unless the modifications are expressly approved in the manual. The user could lose the authority to operate this apparatus if an

unauthorized change or modification is made.

RADIO-TV INTERFERENCE

This apparatus has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This apparatus

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this apparatus does cause harmful interference to radio or television reception, which can be determined by turning the apparatus off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the apparatus and receiver.

3) Connect the apparatus into an outlet on a circuit different from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

DECLARATION OF CONFORMITY

Trade Name: MAGNAVOX

Responsible Party: FUNAI CORPORATION, Inc.

Address: 19900 Van Ness Avenue, Torrance, CA 90501 U.S.A.

Telephone Number: 1-866-341-3738

Model: 22MF330B/19MF330B

This Class B digital apparatus complies with Canadian ICES-003. StandardTelevision Receiving Apparatus, Canada BETS-7/NTMR-7

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

WARNING: Batteries (battery pack or battery installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Disconnect the mains plug to shut off when find trouble or not in use.The mains plug shall remain readily operable.

This apparatus should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided.

Make sure to leave a space of 2.8 inches (7cm) or more around this apparatus.

WARNING: To prevent injury, this apparatus must be securely attached to the wall in accordance with the instructions.

Like all LCD products, this set contains a lamp with Mercury, please dispose of according to all Local, State and

Federal laws. For the disposal or recycling information, contact:

www.mygreenelectronics.com or www.eiae.org

Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or

climbing on it. A falling unit can cause serious injury or even death.

NOTE ABOUT RECYCLING

•

This unit’s packaging materials are recyclable and

can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or

incinerated but disposed of in accordance with your

local regulations concerning chemical wastes.

Trademark Information

•

HDMI, the HDMI Logo, and High-Deﬁnition Multimedia Interface

are trademarks or registered trademarks of HDMI Licensing LLC

in the United States and other countries.

TO AVOID THE HAZARDS OF ELECTRICAL

SHOCK AND FIRE

•

Do not handle the AC power cord with wet hands.

Do not pull on the AC power cord when disconnecting it from an

AC outlet. Grasp it by the plug.

Manufactured under license from Dolby Laboratories. Dolby and

the double-D symbol are trademarks of Dolby Laboratories.

•

Do not put your ﬁngers or objects into the unit.

LOCATION AND HANDLING

•

Do not install the unit in direct sunlight, near strong magnetic

ﬁelds, or in a place subject to dust or strong vibration.

Avoid a place with drastic temperature changes.

Install the unit in a horizontal and stable position. Do not place

anything directly on top or bottom of the unit. Depending on

your external devices, noise or disturbance of the picture and/or

sound may be generated if the unit is placed too close to them.

In this case, please ensure enough space between the external

devices and the unit.

•

ENERGY STAR^®is a joint program of the U.S. Environmental

Protection Agency and the U.S. Department of Energy helping

us all save money and protect the environment through energy

efﬁcient products and practices.

Consumer Notice:

•

Depending on the environment, the temperature of this unit may

increase slightly.This is not a malfunction.

Be sure to unplug the AC power cord from the AC outlet before

carrying the unit.

ThisTV has been set to maximize energy efﬁciency while

delivering the best possible picture using the factory installed

home mode settings.

Changing or enabling other features in thisTV (e.g. brightened

backlighting) will possibly increase energy consumption beyond

the original ENERGY STAR^®qualiﬁed limits.

•

The American Academy of Pediatrics discourages television

viewing for children younger than two years of age.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Features

INTRODUCTION

• DTV/TV/CATV

You can use your remote control to select channels which

are broadcast in digital format and conventional analog

format. Also, cable subscribers can access their cableTV

channels.

Contents

• Information Display (ATSC only)

Important Safety Instructions

Trademark Information

You can display the title, contents and other information of

the current DTV program on theTV screen.

• Autoprogram

INTRODUCTION

This unit automatically scans and memorizes channels

available in your area, eliminating difficult setup procedures.

• Child Lock

This feature allows you to block children’s access to

inappropriate programs.

• Closed Caption Decoder

Built-in closed caption decoder displays text for closed

caption supported programs.

• MTS/SAPTuner

Audio can be selected from the remote control.

• Auto Shut Off Function

Features

Supplied Accessories

Symbols Used in this Manual

Attaching the Base

Fixing the Unit onYour Furniture

Control Panel

Terminals

Remote Control Function

Installing the Batteries

If there is no input signal and no operation for 15 minutes,

the unit will turn off automatically.

PREPARATION

Antenna Connection

• SleepTimer

Connection to Cable Receiver or Satellite Box

External Device Connection

Plug In the AC Power Cord

Initial Setup

This feature will automatically turn off the power of the unit at

a specific time.

• Choices for On-screen Language

Select your on-screen language:

English, Spanish or French.

• Stereo Sound Function

WATCHINGTV

• PLL Frequency SynthesizedTuning

SleepTimer

Switching Each Input Mode

Freeze Mode

Channel Selection

TV Screen Display Mode

Sound Functions

TV Screen Information

Reducing the Brightness

Fun-Link Options

Provides free and easy channel selection and lets you tune

directly to any channel using the number and decimal point

" " buttons on the remote control.

•

• Various Adjustment for Picture and Sound

Customizes image quality suitable for your room and sets

your sound preference.

• Fun-Link via HDMI Link

(HDMI Cable not Included)

Fun-Link allows your other HDMI link devices (such as

Magnavox DVD) to be controlled by the HDMI cable

connected to yourTV.

OPTIONAL SETTING

Main Menu

• HDMI Input

Autoprogram

Channel List

• ComponentVideo Input

• PC Input

• S-Video Input

• AV Input

• Digital Audio Output

• Headphone Audio Output

Add Channels

Antenna Conﬁrmation

Language Selection

Picture Adjustment

Sound Adjustment

Closed Caption

Child Lock

PC Settings

Fun-Link

Energy Saving Mode

Location

Current Software Info

TROUBLESHOOTING

Troubleshooting Guide

FAQ

transmitted, disseminated, transcribed, downloaded or stored in any storage

medium, in any form or for any purpose without the express prior written

consent of Funai. Furthermore, any unauthorized commercial distribution of this

manual or any revision hereto is strictly prohibited.

Information in this document is subject to change without notice. Funai

reserves the right to change the content herein without the obligation to

notify any person or organization of such changes.

INFORMATION

Glossary

Maintenance

General Speciﬁcations

Electrical Speciﬁcation

Other Speciﬁcations

Limited Warranty

with the

design is a registered trademark of Funai Electric Co.,

Ltd. and may not be used in any way without the express written consent

of Funai. All other trademarks used herein remain the exclusive property

of their respective owners. Nothing contained in this manual should be

construed as granting, by implication or otherwise, any license or right to

use any of the trademarks displayed herein. Misuse of any trademarks or

any other content in this manual is strictly prohibited. Funai shall aggressively

enforce its intellectual property rights to the fullest extent of the law.

Download from Www.Somanuals.com. All Manuals Search And Download.

Supplied Accessories

Attaching the Base

You must attach the base to the unit to have it as a table top

unit. Be sure the front and rear of the base match the proper

direction.

Owner’s manual

26263

Quick Start

26264

)

(1EMN

)

(1EMN

Spread a thick and soft

cloth over a table as

shown.

Place the main unit face

down onto it. Make sure

not to damage the screen.

Insert 2 hooks under the

bottom of the main unit

into base holes. (shown by

Remote control

(NF804UD)

Batteries

(AAA, 1.5V x 2)

➁

arrow ), then move the

➀

base in the direction as

shown by arrow until it

➁

➀

stops and the 3 mounting

holes are aligned. Make

sure not to put the AC

power cord between the

base and the unit.

Screw kit

for attaching the base

19876

(1ESA

)

Drive Phillips pan screws

into the 3 threaded holes

at the bottom of the base

until they are tight.

•

If you need to replace these accessories, please refer

to the part No. with the illustrations and call our toll

free customer support line found on the cover of this

manual.

To remove the base from this unit

Unscrew the Phillips pan screws on step 3

•

After the screws are removed, move the base in the opposite direction as

shown by arrow on step 2, then pull the base up toward the rear of the

Note

➁

unit. Be careful not to drop the base when you remove it.

If you lose the screws, please purchase M4×12 Phillips head screws at your

local store.

•

Note

When attaching the base, ensure that all screws are tightly fastened. If the

base is not properly attached, it could cause the unit to fall, resulting in

injuries as well as damage to the unit.

•

Symbols Used in this Manual

Make sure to use a table which can support the weight of this unit and is

larger than this unit.

•

The following is the description for the symbols used in

this manual. Description refers to:

Make sure the table is in a stable location.

When attaching the base, ensure that FRONT written on the base is

upward. If it's not upward, the 2 hooks don't ﬁt in the base.

•

ATSC

NTSC

: DigitalTV operation

:Analog/CableTV operation

Fixing the Unit onYour Furniture

Screw this unit on your furniture tightly using wood screws

•

If neither symbol appears, the operation is applicable to

both.

(not supplied) in the 2 holes at the back of the base as shown.

Recommended screw dimension : 5.1 x 20 mm

•

rear of this unit

Note

When you remove this unit make sure to unscrew the wood screws from

your Wood Stand, Furniture and other wood item.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Control Panel

POWER

p.15

p.16

➠

2 CHANNEL +/

Press to select channels or move up ( ) / down (–)

through the main menu items.

3 MENU

p.19

p.17

➠

4 VOLUME +/

Press to adjust the volume or move right ( ) / left (–)

through the main menu items.

5 STAND BY indicator

Lights up red when power is off.

6 POWER ON indicator

STAND BY

POWER ON

Lights up green when power is on.

POWER

VOLUME

CHANNEL

7 Infrared

sensor window

Receives infrared rays transmitted from the remote

control.

Download from Www.Somanuals.com. All Manuals Search And Download.

Terminals

Side Panel

8 HDMI 2 Input jack

p.10, 11

➠

9 S-Video / CompositeVideo / Audio (L/R)

Input jacks forVIDEO

p.12

➠

TERMINAL

10 Headphone Audio Output jack

Headphone connection for personal listening.

HDMI 2

Rear Panel

11 Antenna Input jack

p.10

➠

12 AC power cord

p.14

13 PC (VGA) Input jack

14 HDMI 1 Input jack

p.13

p.10, 11

15 ComponentVideo and Audio (L/R) Input jacks

HEAD PHONE

p.10, 12

➠

16 Digital Audio Output jack

p.13

17 Audio Input jack for PC connection

p.13

➠

Mini-plug audio cable connection from your PC.

18 Audio (L/R) Input jacks for HDMI 1

p.11

➠

Audio cable connection from your DVI device.

(For HDMI 1 Input jack only)

Note for service terminal

service terminal (service use only)

Use this terminal only when a software update is necessary.

User should not connect any devices to the terminal such as digital camera,

keyboard, mouse, etc. (because these will not work).

•

The software update is, in most cases, handled by an authorized service

person or in some circumstances the user may be asked to do the software

update themselves.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Remote Control Function

(power)

p.15

p.17

p.16

➠

2 SAP

3 SOURCE

4 FREEZE

Press to freeze screen image.

5 OK

p.15

p.18

➠

6 ▲/▼/◄/►(cursor)

7 BACK

Press to return to the previous menu operation.

8 VOL +/−

p.17

p.16

➠

9 PREV CH

Press to return to previously viewed channel.

10 SLEEP

11 FORMAT

p.16

p.17

➠

Press to select aspect ratio available for theTV screen.

12 RED/GREEN/BLUE/YELLOW

p.30

➠

Functionally useful for Fun-Link.

13 MENU

p.19

➠

14 INFO

15 REV E/FWD D

p.18

p.30

Press to search backward or forward through the disc

PLAY B

Press to begin the disc playback.

SKIP H/SKIP G

Press to skip backward or forward chapters, titles or

tracks of the disc.

p.30

➠

p.30

➠

PAUSE F

Press to pause the disc playback.

STOP C

p.30

➠

p.30

➠

Press to stop the disc playback

16 MUTE

p.17

p.16

p.18

➠

17 CH +/−

18 ECO

Press to reduce the brightness.

19 Number buttons

(dot)

p.16

➠

•

Press to shift the subchannel from the main channel.

20 FUN-LINK OPTIONS p.18, 30

➠

When using a universal remote control to operate this unit.

Press to call up various menu from your Fun-link device

connected through an HDMI cable.

Make sure the component code on your universal remote control is set

•

to our brand. Refer to the manual accompanying your remote control for

more details.

We do not guarantee 100% interoperability with all universal remote

controls.

•

Installing the Batteries

Install the batteries (AAA, 1.5V x 2) matching the polarity

Note

Buttons in gray background (

) are not available unless you are

connected to devices that are compatible with Fun-Link function.

We do not guarantee 100% interoperability with other brands of HDMI link

compliant devices.

•

indicated inside battery compartment of the remote control.

•

Battery Precautions:

Be sure to follow the correct polarity as indicated in the battery

compartment. Reversed batteries may cause damage to the device.

•

Do not mix different types of batteries together (e.g.Alkaline and

Carbon-Zinc, or rechargeable batteries like ni-cad, ni-mh, etc) or old

batteries with fresh ones.

•

If the device is not to be used for a long period of time, remove the

batteries to prevent damage or injury from possible battery leakage.

•

Do not try to recharge batteries; they can overheat and rupture.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

Connection to Cable Receiver or

Satellite Box

PREPARATION

Use an HDMI or component video cables to connect the

HDMI or the ComponentVideo Input jacks of the unit to

the HDMI or the component video output jacks of the cable

receiver/satellite box.

If you connect to the unit’s ComponentVideo Input jacks,

connect audio cables to the Audio L/R Input jacks right beside

the ComponentVideo connector.

No supplied cables are used with these connections:

Please purchase the necessary cables at your local store.

High Speed HDMI cable (also known as HDMI category 2

cable) is recommended for the better compatibility.

Before you connect:

Be sure your antenna or other device is connected properly

before plugging in the AC power cord.

e.g.)

satellite dish

Antenna Connection

ANT IN

RF coaxial cable

Connect the RF coaxial cable on your home outlet to the

antenna input jack of this unit.

e.g.)

cableTV signal

cable receiver/

VHF / UHF

analog or

DTV antenna

STEREO

PCM

including PPV

satellite box

AUDIO OUT

COMPONENT VIDEO OUT

HDMI OUT

Pb/Cb

Pr/Cr

(green) (blue)

(red)

RF coaxial cable

component video cables

(red/blue/green) and audio cables

cableTV signal

HDMI cable

rear of this unit

SERVICE

TERMINAL

HDMI 2

(green)

Once connections are completed, turn on the unit and begin initial

setup. Channel scanning is necessary for the unit to memorize all

available channels in your area.[Initial Setup] ➠ p.15

(blue)

(red)

side or rear of

this unit

Note

You can also connect this unit to the cable receiver or satellite box

other than the HDMI or the component video output jacks because

they might have different output jacks.

Required cables and connecting methods of the cable receiver/

satellite box, or the availability channel for the clear QAM may differ

depending on the cable/satellite provider. For more information,

please contact your cable/satellite provider.

If you have any question about the DTV’s antenna, visit www.antennaweb.

org for further information.

Depending on your antenna system, you may need different types of

combiners (mixers) or separators (splitters). Contact your local electronics

store for these items.

For your safety and to avoid damage to this unit, please unplug the RF

coaxial cable from the antenna input jack before moving the unit.

If you use an antenna to receive analogTV, it should also work for DTV

reception. Outdoor or attic antennas will be more effective than a set top

or inside antenna.

•

To switch your reception source easily between antenna and cable, install an

antenna selector.

If you are not receiving a signal from your cable service, contact the Cable

provider.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

English

HDMI-DVI Connection

External Device Connection

Use an HDMI-DVI conversion cable to connect the unit to

external video devices equipped with DVI output jack.

HDMI Connection

e.g.)

audio cables

HDMI connection offers the highest picture quality.

HDMI (High-Deﬁnition Multimedia Interface) transports high deﬁnition

video and multi-channel digital audio through a single cable.

cable receiver or satellite box

e.g.)

with the DVI output jack

AUDIO OUT

BD/DVD recorder

with the HDMI output jack

HDMI OUT

STEREO

PCM

TITLE

CHAPTER 15

REPEAT A-B

DVI OUT

HDMI-DVI

conversion cable

SERVICE

TERMINAL

side or rear of this unit

HDMI

rear of this unit

Note

For HDMI connection

The unit accepts 480i, 480p, 720p 1080i of video signals, and 32kHz,

44.1kHz and 48kHz of audio signals.

•

This unit accepts only 2 channel audio signal (LPCM).

You need to select "PCM" for the digital audio of the device you connected

or check the HDMI audio setting.There may be no audio output if you

select "Bitstream", etc.

•

This unit accepts only signals in compliance with EIA861.

•

For HDMI-DVI connection

The unit accepts 480i, 480p, 720p 1080i video signals.

HDMI-DVI connection requires separate audio connections as well and the

audio signals are converted from digital to analog.

DVI does not display 480i image which is not in compliance with EIA/

CEA-861/861B.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

S-Video Connection

No supplied cables are used with these connections:

Please purchase the necessary cables at your local store.

S-Video connection offers good picture quality for video

devices connected to the unit. If you connect to the unit’s

S-Video Input jack, connect audio cables to the Audio L/R

Input jacks right beside the CompositeVideo connector.

ComponentVideo Connection

e.g.)

BD/DVD recorder, camcorder andVCR with

the S-Video output jack

ComponentVideo connection offers better picture quality for

video devices connected to the unit.

TITLE

CHAPTER 15

REPEAT A-B

If you connect to the unit’s ComponentVideo Input jacks,

connect audio cables to the Audio L/R Input jacks right beside

the ComponentVideo connector.

S-VIDEO

OUT

AUDIO OUT

e.g.)

BD/DVD recorder with

the component video output jack

COMPONENT VIDEO OUT

Pb/Cb

Pr/Cr

TITLE

CHAPTER 15

REPEAT A-B

S-Video

cable

(green) (blue)

(red)

AUDIO OUT

component video

cables

(red/blue/green)

audio cables

HEAD PHONE

audio cables

side of this unit

CompositeVideo Connection

CompositeVideo connection offers standard picture quality

for video devices connected to the unit. If you connect to

the unit’s CompositeVideo Input jack, connect audio cables

to the Audio L/R Input jacks right beside the Composite

Video connector.When the audio jack of the video device is

monaural, connect an audio cable to the Audio L Input jack.

rear of this unit

e.g.)

AUDIO OUT

VIDEO

OUT

Note

camcorder

video game

The unit accepts 480i/480p/720p and 1080i of video signals for this

connection.

•

STAND-BY

STEREO

VCR

audio cables

video cable

HEAD PHONE

side of this unit

Note

If you connect to the S-Video Input jack and the CompositeVideo Input

jack at the same time, the S-Video connection will have priority.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Digital Audio Output Connection

PC Connection

(for digital broadcasting only)

This unit is equipped with a PC input jack. If you connect this

unit to your PC, you can use this unit as a PC monitor.

Use anVGA cable for this connection and it requires stereo

mini plug audio cable as well.

If you connect this unit to an external digital audio device, you

can enjoy multi-channel audio like 5.1ch digital broadcasting

sound.

Use a digital audio coaxial cable to connect the unit to external

digital audio devices.

e.g.)

rear of this unit

e.g.)

Dolby Digital

decoder

rear of this unit

DIGITAL AUDIO

COAXIAL IN

stereo mini plug

cables

digital audio coaxial cable

VGA cable

personal computer

VGA cable should be

with ferrite core.

The following video signals can be displayed:

Format

VGA

Resolution

640 x 480

Refresh rate

SVGA

XGA

800 600

1 024 768

1 280 x

768

1 360 768

60Hz

WXGA

Other formats or non-standard signals will not be displayed

correctly.

Note

Please purchase theVGA cable that has a ferrite core.

The following operations may reduce noise.

- Attach a ferrite core to the AC power cord of your PC.

•

- Unplug the AC power cord and use the built-in battery of your PC.

Download from Www.Somanuals.com. All Manuals Search And Download.

Plug In the AC Power Cord

Make sure that the AC power cord must be plugged to an

AC outlet after all the necessary connections are completed.

rear of this unit

ocmede.tpl

AC power cord

AC outlet

Caution:

Do not connect the AC power cord to a power supply outside the

indicated voltage of this unit (AC 120V).

•

Connecting the AC power cord to a power supply outside of this range may

result in ﬁre or electrical shocks.

Note

Each time you plug in the AC power cord, no operations will be performed

for a few seconds.This is not a malfunction.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Use ◄/► to select the desired location setting, then

These operations are accessible by remote control.

Some may also be accessible by controls on the main unit.

press OK

Initial Setup

Select “Retail” or “Home” for your location.

Initial Setup

This section will guide you through the unit’s initial setting

which includes selecting a language for your on-screen menu

and autoprogram, which automatically scans and memorizes

viewable channels.

Home

Retail

Select

Before you begin:

Make sure the unit is connected to antenna or cable.

Select [Retail] store, the unit will be set up with

predefined setting for retail displays. In this setting, the

power consumption may possibly exceed the limited

requirement of the ENERGY STAR^®qualification.

1 After making all the necessary connections,

press to turn on the unit.

• Select [Home], the unit is set to maximize the energy

efficiency for home setting and it can be adjusted

through a choice of picture and sound quality according

to your preference.

• When the initial setup is completed, the lowest

memorized channel with the confirmation message of

the location setting will be displayed on theTV screen.

• It may take a few moments to turn on the unit for the

first time.

• [Initial Setup] menu appears automatically after the

unit is turned on.

2 Use ▲/▼ to select the on-screen language from the

choices (English/Español/Français) on the right side of the

TV screen.

Note

If you are not receiving a signal from your cable service, contact the Cable

provider.

If you press or MENU during autoprogram, this setting will be canceled.

The initial autoprogram function can be executed for either [Antenna] or

[Cable] only once.When you change the connection (Antenna/Cable),

•

3 Use ▲/▼ to select [Antenna] for TV channels or [Cable]

for CATV channels, then press OK

•

Initial Setup

set [Autoprogram] again.

p.19

➠

Make sure the antenna is connected to ''ANT. IN'' jack.

Antenna

If there is no signal input from the antenna terminal and no operation for

several seconds after you turn on the unit, [Helpful Hints] appears. Follow

the instructions listed on theTV screen.

•

Select your signal source.

Cable

Skip

Initial Setup

Antenna

Cable

ANT.IN

Retry

No channel is registered.

Try Autoprogram again?

Later

BACK

Verify that you have a cable connected to the "ANT. IN" jack on the back

of the TV, the channel installation process searches this connection. If

you are using a cable or satellite box, please confirm the input which

you have connected the box and press "SOURCE" key on the remote

control to select the appropriate source input.

Select

Back

Skip

[Autoprogram] will begin.

Initial Setup

Select

Skip

Please wait while the system is scanning for channels. Auto programming

may take more than 20 minutes to complete.

You must set [Home] in step 4. Otherwise, the settings of picture and

sound quality you adjusted will not be memorized after you turn off the

unit.

•

Digital channels

Analog channels

0 ch

After an initial setup is completed...

• If you want to scan the channels automatically again.

Skip

[Autoprogram]

➠ p.19

• You can add the desired cable and analog channels

unmemorized by autoprogram.

[Add Channels]

➠ p.20

• If you want to change to another language.

[Language Selection] ➠ p.21

• If you want to change the location setting.

[Location]

➠ p.31

Download from Www.Somanuals.com. All Manuals Search And Download.

WATCHINGTV

SleepTimer can be set to automatically turn off the unit after an incremental

period of time.

Press SLEEP repeatedly to change the amount of time (increases

Sleep

120min.

the time by 30 minutes up to 120 minutes) until shut off.

Press SLEEP once to call up the display for checking the remaining time.

To cancel sleep timer, press SLEEP repeatedly until

[Sleep Off] is displayed.

•

Switching Each Input Mode can easily switch with the remote control

betweenTV (ATSC or NTSC) and external devices when they are connected to the unit.

Press SOURCE or

CH +

repeatedly to cycle through the input modes.

Source

e.g.)

TTVV

Video

11.1

DTV/TV channel

Video

Component

HDMI1

Component

HDMI1

HDMI2

HDMI3

HDPMCI3

HDMI2

Pressing CH − reverses the direction of the input modes.

•

can freeze the image shown on theTV screen for 5 minutes.

Freeze Mode

Press FREEZE to freeze the image.

Freeze

The sound output will not be paused.

To cancel freeze mode, press any buttons except

•

Channel Selection

Select channels by using CH +/− or the Number buttons

•

To select the memorized channels,

use CH +/− or the Number buttons

To select the non-memorized channels,

use the Number buttons

•

11.1

To use the Number buttons

ATSC

When selecting digital channel 11.1

Be sure to press before entering the subchannel number.

NTSC

When selecting cable or analog channel 11

Press PREV CH to return to the previously viewed channel.

[No Signal] will appear on theTV screen after the subchannel broadcast is over.

[Audio only program] message will appear on the TV screen, when you receive

only sound signal.

•

Note

Download from Www.Somanuals.com. All Manuals Search And Download.

English

TV Screen Display Mode

5 types of display modes can be selected when the broadcasting station is sending 16:9 or 4:3 video signal. And 3 types of display

modes can be selected for PC input signal.

Press FORMAT repeatedly to switch the TV aspect ratio.

For 16:9 video signal

Normal displays a 16:9 picture at its original size.

4:3 displays a 16:9 picture at a 4:3 size; the picture

is shortened horizontally. Sidebars appear on both

edges of the screen.

Movie Expand displays a 16:9 picture that is

vertically stretched to ﬁll the screen. This only crops

out the top of the picture.

Normal

4:3

Movie Expand

Zoom displays a 16:9 picture at its maximum size

without changing its horizontal and vertical ratio.

Wide displays a horizontally stretched picture.This

crops out the left and right sides of the picture.

Wide

Zoom

Normal displays a 4:3 picture at its original size.

Sidebars appear on both edges of the screen.

For 4:3 video signal

16:9 displays a 4:3 picture at a 16:9 size; the picture is

stretched horizontally to ﬁll the screen.

Movie Expand displays a 4:3 picture at a 16:9 size;

the picture is stretched more vertically at the top of

the screen. This crops out the top of the picture.

Normal

16:9

Movie Expand

Zoom displays a 4:3 picture at a 16:9 size; at its

maximum size that is more vertically stretched to ﬁll

the screen.This crops out the top and bottom of the

picture.

Wide

Zoom

Wide displays the picture with its center at the

original size and the edges stretched horizontally to

ﬁll the screen.

For PC input signal

Normal displays a proportionately stretched picture.

Sidebars appear on both edges of the screen.

Full displays a picture that is stretched out of

proportion horizontally to ﬁll the screen.

Dot By Dot displays a picture in its original size.

Normal

Full

Dot By Dot

Sound Functions

describe how to change the audio or the audio language as well as the volume.

Volume Adjustment

Use VOL +/− to adjust the volume.

Volume

will be displayed for a few

Silence Mode

seconds when adjusting the volume.

Press MUTE to turn off the sound temporarily.

Mute

will be displayed for a few seconds.

Press MUTE again or VOL +/− to recover the

original volume.

•

Switching Audio Mode

ATSC

NTSC

Press SAP repeatedly to cycle through the available

audio languages.

Press SAP to display the currently selected audio mode.

While receiving an MTS broadcast, press repeatedly to cycle through the

available audio channel.

Available languages differ depending on the

broadcast.

[Other] is displayed when the audio language

cannot be acquired, or the acquired languages are

other than English, Spanish or French.

•

SAP/STEREO

e.g.) When all audio are available

SAP/STEREO

SAP/MONO

SAP/STEREO

11.1

English 1/3

STEREO : Outputs stereo-audio

SAP

: Outputs second audio program

MONO : Outputs mono-audio

Download from Www.Somanuals.com. All Manuals Search And Download.

TV Screen Information

Reducing the Brightness

You can display the currently selected channel or other

information such as the audio mode on the TV screen.

In the digital mode, the detailed broadcasting information for

the current channel such as program title, program guides are

displayed.

Backlight brightness can be reduced which may save on power

consumption more than you just set [On] in [Energy Saving

Mode]. p.31

➠

Press ECO once to reduce the brightness.

Press ECO again to increase the brightness.

Press INFO

Note

Even if this function is in effect, the brightness will be increased when you

change [Energy Saving Mode] on or off due to the energy saving mode has

priority.

•

ATSC

You must set [Home] in [Location]

Otherwise, the settings you adjusted will not be memorized after you turn

off the unit.

p.31

•

➠

A Day of Memories

KABC

11.1

English 1/2

A quarter-century ago,which may now qualify as the

good old days of newspapering,run-of-paper sales

accounted for 80 percent of the industry's advertising

revenues.Department stores and supermarket were

1080i HD

16:9

6, 7, 8

Rating

TV: TV-14

Fun-Link Options

NTSC

If you have our brand products such as BD player or DVD

recorder that are compatible with Fun-Link functions, connect

them to this unit via an HDMI cable so you can simply operate

various items from this unit's remote control.

SAP/STEREO

480i SD

4:3

6, 7, 8

Before you begin:

You must set [On] in [Device Control] and

TV-PG DLSV CC

[Fun-Link Control]

p.30

➠

Otherwise, FUN-LINK OPTIONS

you connected our brand devices to this unit.

does not work even if

1 program title

2 program guide

(The program guide added to broadcasting

information is displayed to a maximum of 4 lines.)

3 broadcast station

4 channel number

5 audio language (ATSC)/audio mode (NTSC)

[Switching Audio Mode]

6 effective scanning lines and scan mode

7 TV format

To enjoy Fun-Link, verified and recommended devices

are as follows;

MAGNAVOX

NB530MGX

NB500MG1F

MBP1100/F7

SYLVANIA

NB530SLX

NB500SL1

p.17

➠

Press FUN-LINK OPTIONS

to display

8 program aspect ratio

9 CC (not available if closed caption is set to [Off])

10child lock rating

[Fun

Link Options] menu

Fun-Link Options

Device-menu

Device-contents

Device-favorite

• To clear the display, press INFO again.

You can also press BACK

Note

This function allows you to control

the menu of your connected Fun-Link

device.

Device-menu

When the program guide consists of more than 4 lines, use ▲/▼ to scroll.

[No description provided.] is displayed when the program guide is not

provided.

•

This function allows you to control the

top menu of your DVD or Blu-ray discs.

Device-contents

Device-favorite

While the program guide is displayed, the closed caption function is

interrupted.

In external input mode, the following screen is displayed;

e.g.) When an external device is connected toVideo Input jack.

•

This function allows you to control the

pop-up menu of your Blu-ray discs.

Use ▲/▼/◄/►/OK on this unit's remote control to

Video

480i SD

operate the desired functions for your devices.

TV-PG DLSV

Note

The information display will automatically disappear in 1 minute.

Some of Fun-Link functions may not be available depending on your

Fun-Link devices or discs.

•

We do not guarantee 100% interoperability with other brands of HDMI link

compliant devices.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Autoprogram

OPTIONAL SETTING

If you switch wires (e.g. between antenna and CATV) or if you

move the unit to a different area after the initial setting, or if

you restore the DTV channels you deleted, it is recommended

to use Autoprogram to perform a new channel search.

Main Menu

This section describes the overview of the main menu

displayed when you press MENU. The main menu consists of

the function setting items below.

Before you begin:

Make sure the unit is connected to antenna or cable.

Press MENU to display the main menu.

Picture

2 Use ▲/▼ to select [Setup], then press OK

Use ▲/▼ to select [Autoprogram], then press OK

Use ▲/▼ to select an appropriate option, then press OK

Sound

Press MENU

Setup

Features

Language

Back

Picture

Sound

Autoprogram will rescan all channels.

Auto programming may take more than 20

minutes to complete.

Antenna

Cable

Picture [Picture Adjustment]

p.22

p.23

p.19

➠

Setup

Select your signal source.

Sound

Setup

[Sound Adjustment]

[Autoprogram]

Features

Language

Antenna

•

You can automatically scan the viewable channels.

[Channel List] p.20

Cable

ANT.IN

➠

•The Channels that were autoprogrammed are in

this Channel list,use CH +/

−

to access them.

• When connected toVHF/UHF antenna,

[Add Channels]

p.20

select [Antenna]

➠

• When connected to CATV, select [Cable]

• [Autoprogram] will begin.

•You can add TV channels that were not found by

the autoprogram scan.

Features [Closed Caption]

p.24

➠

•

You can change the display closed caption format

which displays the dialogue of aTV program or

other text information across theT

V screen.

Please wait while the system is scanning for channels. Auto programming

may take more than 20 minutes to complete.

75%

[Child Lock]

p.27

➠

•You can set viewing limitations.

Digital channels

Analog channels

10 ch

6 ch

[PC Settings]

•You can adjust the position, stability and clarity of

the PC screen.

p. 29

➠

Exit

[Fun-Link]

p.30

➠

• When the scanning and memorizing are completed, the

lowest memorized channel will be displayed.

•You can set Fun-Link options.

[Energy Saving Mode]

[Location]

p.31

➠

Note

After setting [Autoprogram], using CH +/

−

on the remote control skips

unavailable programs automatically.

If you are not receiving a signal from your cable service, contact the Cable

provider.

•

Switch setting from [Retail] to [Home] to allow the

desired [Picture] and [Sound] mode to be kept in

memory.

•

If you press or MENU during autoprogram, the setting will be canceled.

Even if [Autoprogram] is completed, the channel setting will be lost if the

AC power cord is unplugged before turning off the unit by pressing

The PIN code will be required once you set a PIN code in the [Child Lock]

•

[Current Software Info]

p.31

p.21

➠

Language [Language Selection]

•

•Change the Main Menu language.

p.27

➠

If you want to change your PIN code, follow the instruction of

[Change PIN]

p 28

➠

Download from Www.Somanuals.com. All Manuals Search And Download.

Channel List

Add Channels

The channels selected here can be skipped when selecting the

channels using CH +/

Those channels can still be selected with the Number buttons

This function lets you add the channels that were not added

by the autoprogram due to reception conditions at the initial

setting.

Press MENU to display the main menu.

2 Use ▲/▼ to select [Setup], then press OK

3 Use ▲/▼ to select [Channel List], then press OK

2 Use ▲/▼ to select [Setup], then press OK

3 Use ▲/▼ to select [Add Channels], then press OK

4 Use ▲/▼ to select the channel you want to remove, then

4 Use the Number buttons to enter the number of the

press OK

channel you want to add, then press OK

DTV

11.1

11.2

11.3

Picture

Sound

Setup

Highlight channels for Ch Up/Down key selection.

Add channels

Picture

Sound

Features

Language

For analog channels, select a channel to be

added using number keys.

Setup

For digital channels, you must perform

Autoprogram function.

Features

Language

BACK

Ch Select

Watch/Skip

Back

• The channel display for the removed channel darkens.

You will not be able to select the channel again using

CH +/

BACK

Ch Change

Back

• To reactivate a removed channel, use ▲/▼ and press

OK.The registered channels are highlighted.

5 Press MENU to exit.

• When you remove a main channel, its subchannels are

removed as well.

Note

If setup completes successfully, [Added to the channel list] is displayed.

If external input is used, it is not possible to register the channel and

[Unavailable] will be displayed on theTV screen.

•

5 Press MENU to exit.

By using CH +

/–

, you can select the memorized channels only.

•

Note

The channel with the [DTV] indicated on the display is ATSC.

Otherwise the channel is NTSC.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Antenna Conﬁrmation

ATSC

Language Selection

You can choose English, Spanish, or French as your on-screen

language.

This function lets you check the digital signal strength of each

channel.

1 Press MENU to display the main menu.

Press MENU to display the main menu.

2 Use ▲/▼ to select [Setup], then press OK

3 Use ▲/▼ to select [Antenna], then press OK

2 Use ▲/▼ to select [Language], then press OK

3 Use ▲/▼ to select [English] [Español] or [Français], then

press OK

4 Use the Number buttons or CH +/ to select the

channel for which you want to check the digital signal

strength.

Picture

Select your menu language.

English

Español

Français

Sound

Setup

11.1

Seleccione el idioma para el menú.

Sélectionnez la langue du menu.

Features

Language

Back

Picture

Sound

Setup

Features

Language

4 Press MENU to exit.

Current 50 Max

Note

If you need the English menus instead of the Spanish or French menus, press

MENU. Use ▲/▼ to select [Idioma] or [Langue], then press OK

Use ▲/▼ to select [English], then press OK

•

Ch Change

Press MENU to exit the main menu.

• If the channel is set to analog (cable) channel or

external input, you cannot confirm the antenna

condition.

Video

Back

Picture

Sound

Setup

Indicator is available for digital

broadcasting only.

Features

Language

Ch Change

5 Press MENU to exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Brightness, Contrast, Color, Tint,

Sharpness, ColorTemperature

Picture Adjustment

You can adjust picture mode, or customize the picture quality

as your preference.

You can only adjust the following options when you set

to [Personal]

[Smart Picture]. Use ▲/▼ to select the

desired setting, then use ◄/► to adjust.

Before you begin:

You must set [Home] in [Location]

Otherwise, the settings you adjusted will not be memorized

after you turn off the unit.

p.31

➠

Brightness

◄

Press ►

to increase

brightness

Brightness

to decrease

brightness

Adjust

Move

1 Press MENU to display the main menu.

Contrast

Press ◄

to decrease

contrast

Press ►

to increase

contrast

Contrast

2 Use ▲/▼ to select [Picture], then press OK

Adjust

Color

3 Use ▲/▼ to select the item you want to adjust, then press

Press ◄

to decrease

color intensity color intensity

Press ►

to increase

Color

Adjust

Tint

◄

Press ►

to add green

Smart Picture

Brightness

Contrast

Personal

Picture

Sound

Tint

to add red

Adjust

Setup

Color

Features

Language

Sharpness

Press ◄

to soften

Press ►

to sharpen

Tint

Sharpness

Color Temperature

Adjust

Normal

ColorTemperature

◄

to add warm

colors

Press ►

to add cool

colors

Color Temp. Normal

Adjust

Move

4 Adjust the following items.

Smart Picture

5 Press MENU to exit.

Use ▲/▼ to select the desired setting, then press OK

([Personal] [Standard] [Sports] [Movie], and [Game])

Personal

Standard

Sports

Picture

Sound

Smart Picture

Brightness

Contrast

Setup

Color

Movie

Features

Language

Tint

Game

Sharpness

Color Temperature

Download from Www.Somanuals.com. All Manuals Search And Download.

English

TV Speakers

Sound Adjustment

Select the audio output from the unit’s speakers, or not.

If your ampliﬁer is HDMI link function compatible and

connected by an HDMI cable to this unit, some sound

operations such as volume up can be changed by using

this unit’s remote control. Make sure [Fun-Link Control]

You can adjust the sound mode, equalizer and some other

sound functions.

Before you begin:

You must set [Home] in [Location]

p.31

➠

is set to [On]

p.30

➠

Otherwise, the settings you adjusted will not be memorized

after you turn off the unit.

Use ▲/▼ to select the desired option, then press OK

1 Press MENU to display the main menu.

Picture

Sound

On":

Off

Sound will be output from the TV

speakers.

"Off":

Sound will not be output from the TV

speakers.

"Ext. Amp":

“Operation is possible by connecting to the

HDMI-CEC compatible amp with a

HDMI cable.

2 Use ▲/▼ to select [Sound], then press OK

Ext. Amp

Setup

Features

Language

3 Use ▲/▼ to select the item you want to adjust, then press

For details look in the user manual.”

Smart Sound

Equalizer

Standard

Picture

Sound

The sound will be output from the unit’s

speakers.

TV Speakers

Primary MTS

Ext. Amp

Stereo

Setup

Features

Language

The sound will not be output from the

unit’s speakers.

Off

You can control audio output from your

connected HDMI link devices by using this

unit's remote control.

Ext. Amp

Note

4 Adjust the following items.

We do not guarantee 100% interoperability with other brands of HDMI

link compliant devices.

•

Smart Sound

Use ▲/▼ to select the desired setting, then press OK

Primary MTS

You can set the output mode as a default for the sound

mode (NTSC only).

([Personal] [Standard] [Movie] [Music], and [News])

Smart Sound

Equalizer

Personal

Standard

Movie

Picture

Sound

This setting is not interlocked when you change the

output mode by pressing SAP [Sound Functions] p.17

➠

TV Speakers

Primary MTS

Setup

Use ▲/▼ to select the desired option, then press OK

Music

Features

Language

News

Smart Sound

Equalizer

Picture

Sound

TV Speakers

Primary MTS

Setup

Stereo

Mono

SAP

Features

Language

Equalizer

Adjust tonal quality for each frequencies. Use ◄/► to

select the speciﬁc frequency and use ▲/▼ to adjust the

level, then press OK

Stereo

Mono

SAP

Outputs stereo-audio.

Outputs mono-audio.

Picture

Sound

Outputs second audio program.

Setup

Features

Language

Press MENU to exit.

120Hz 500Hz 1.5kHz 5kHz 10kHz

Download from Www.Somanuals.com. All Manuals Search And Download.

Closed Caption

A. Captiioon SSeerrvice

You can view closed captioning (CC) for TV programs,

movies and news. Closed caption refers to text of dialogue or

descriptions displayed on-screen.

4 ^{Use ▲/▼ to select [Caption Service], then press OK.}

Use ▲/▼ to select the desired closed caption, then press

Press MENU to display the main menu.

2 Use ▲/▼ to select [Features], then press OK

Off

Picture

Sound

Caption Service

Digital Caption Service

Caption Style

CC-1

CC-2

CC-3

CC-4

T-1

Use ▲/▼ to select [Closed Caption], then press OK

Setup

Features

Language

See the following description for setting each item.

T-2

Caption Service

Digital Caption Service

Caption Style

Off

Picture

Sound

T-3

T-4

Setup

Features

Language

The primary caption and text services.The

captioning or text is displayed in the same

language as the program’s dialogue (up to

4 lines of script on theTV screen, where

it does not obstruct relevant parts of the

picture).

CC-1 andT-1

CC-3 andT-3

Serve as the preferred data channels.

The captioning or text is often a secondary

language.

Rarely available and broadcasters use them

only in special conditions, such as when

[CC-1] and [CC-3] or [T- 1 ] and [T- 3 ] are

not available.

CC-2, CC-4,

T-2 andT-4

• There are 3 display modes according to programs:

Displays input characters on theTV screen

immediately.

Paint-on mode

Once characters are stored in memory,

Pop-on mode

they are displayed all at once.

Displays the characters continuously by

Roll-up mode

scrolling (max. 4 lines).

Press MENU to exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

B. Digital Cappttiioonn SSeerrviiccee

C. Caption Style

ATSC

In addition to the basic closed caption, DTV has its own closed

caption called digital caption service. Use this menu to change

the settings for digital caption service.

You can change the caption style such as font, color or size,

etc.

Use ▲/▼ to select [Caption Style], then press OK

Use ▲/▼ to select [Digital Caption Service], then press

Use ▲/▼ to select [User Setting], then press OK

5 Use ▲/▼ to select the desired digital caption service, then

press OK

User Setting

Font Style

Off

Picture

Sound

Font0

Middle

White

Solid

Black

Solid

Black

None

Font Size

Setup

Off

Picture

Sound

Caption Service

Digital Caption Service

Caption Style

Font Color

Features

Language

CS-1

CS-2

CS-3

CS-4

CS-5

CS-6

Font Opacity

Background Color

Background Opacity

Edge Color

Setup

Features

Language

Edge Type

6 Use ▲/▼ to select [On], then press OK

Use ▲/▼ to select an item, then press OK. Then use

Select if you do not want digital caption

service.

Off

▲/▼ to select the desired setting and press OK

Select one of these before changing

any other item in [Closed Caption]

menu. Choose [CS-1] under normal

circumstances.

Picture display

CS-1 to CS-6

So, you must be Philip. Hi!

I’m pleeased tto mmeeeett you.

6 Press MENU to exit.

Edge

Note

(Edge Color and EdgeType)

Font

[Digital Caption Service] that you can switch differs depending on the

•

broadcast description.

(Font Style, Font Size, Font Color and Font Opacity

orTransparency)

Background

(Background Color and Background Opacity or

Transparency)

• The setting description for each item is shown on the

next page.

• Review your setting choice made on the next page

by looking in the upper right corner of the displayed

setting box (not all selections show the differences

selected).

Download from Www.Somanuals.com. All Manuals Search And Download.

Font Style

Closed Captioning font style

can be changed as illustrated.

Background Opacity

Background opacity of the

displayed caption can be

switched as illustrated.

Closed Caption

Solid

Flash

Translucent

Transparent

Font Size

Edge Color

Closed Caption

Font size of the displayed

caption can be switched as

illustrated.

Edge color of the displayed

caption can be switched as

illustrated.

White

Black

Red

Large

Middle

Small

Green

Blue

Yellow

Magenta

Cyan

Font Color

EdgeType

Closed Caption

Font color of the displayed

caption can be switched as

illustrated.

Edge type of the displayed

caption can be switched as

illustrated.

White

Black

Red

None

Raised

Green

Blue

Depressed

Uniform

Yellow

Magenta

Cyan

L. Shadow

R.Shadow

Font Opacity

Closed Caption

8 Press MENU to exit.

Font opacity of the displayed

caption can be switched as

illustrated.

Note

Closed caption will not be displayed when you are using an HDMI

connection.

To show the closed caption on yourTV screen, broadcast signal must

contain the closed caption data.

Not allTV programs and commercials have the closed caption or all types

of the closed caption.

•

Solid

Flash

Translucent

Transparent

Captions and texts may not exactly match theTV voice.

Changing channels may delay the closed caption for a few seconds.

Adjusting or muting the volume may delay the closed caption for a few

seconds.

Abbreviations, symbols and other grammatical shortcuts may be used in

order to keep pace with the on-screen action.This is not a malfunction.

The caption or text characters will not be displayed while the main menu

or functions display is shown.

•

Background Color

Background color of the

displayed caption can be

switched as illustrated.

Closed Caption

•

White

Black

Red

If a black box appears on theTV screen, this means that the closed caption

is set to the text mode.To clear the box, select [CC-1] [CC-2] [CC-3]

[CC-4] or [Off]

Green

Blue

If the unit receives poor quality television signals, the captions may contain

errors, or there might be no captions at all. Some possible causes of poor

quality signals are:

•

Yellow

Magenta

Cyan

- Automobile ignition noise

- Electric motor noise

- Weak signal reception

- Multiplex signal reception (ghosts or screen ﬂutter)

Data dropout and Pixelation (for DTV only)

The unit retains the closed caption setting if the power fails.

When the unit receives special effects playback signal (e.g. Search, Slow

and Still) from aVCR’s video output channel (ch3 or ch4), the unit may not

display the correct caption or text.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Child Lock

A. Channel Lock

Child lock reads the ratings for programs, then denies access

to the programs which exceed the rating level you set. With

this function, you can block certain programs inappropriate

for children and any channels or external input modes can be

invisible.

Particular channels or external input modes can be invisible in

this function.

5 Use ▲/▼ to select [Channel Lock], then press OK

6 Use ▲/▼ to select the desired rating, then press OK

1 Press MENU to display the main menu.

repeatedly to switch between [View]

and

[Block]

2 Use ▲/▼ to select [Features], then press OK

3 Use ▲/▼ to select [Child Lock], then press OK

Picture

Video

Sound

Component

Setup

HDMI1

Features

Closed Caption

Child Lock

Picture

Sound

HDMI2

Language

Setup

PC settings

40.1 DTV

Features

Language

Fun-Link

Energy Saving Mode

Location

BACK

Select

View / Block

Back

Home

Current Software Info

7 Press MENU to exit.

4 Use the Number buttons to enter the 4-digit numbers for

your PIN code.

Features

Enter PIN.

Language

B. Setting US Movie ratiinnggss

• When you have not set up your PIN code,

US Movie ratings lock is the rating system created by MPAA.

enter 0 0 0 0

• When the PIN code is correct, [Child Lock] menu is

displayed.

5 Use ▲/▼ to select [US Movie Ratings Lock], then press

See the following description for setting each item.

6 Use ▲/▼ to select the desired rating, then press OK

Channel Lock

Picture

repeatedly to switch between [View] and [Block]

US Movie Ratings Lock

Sound

US TV Ratings Lock

Setup

Canadian English Rating

Canadian French Rating

Region Ratings Lock

Change PIN

Features

Language

Picture

Sound

NC-17

Setup

Features

PG-13

Language

Note

When you select a rating and set it to [Block], the higher ratings will be

blocked automatically.The lower ratings will be available for viewing.

When you set the highest rating to [View], all ratings turn to [View]

automatically.

To block any inappropriate programs, set your limits in [US Movie Ratings

Lock] [USTV Ratings Lock] and [Region Ratings Lock]

•

BACK

Select

View / Block

Back

Rating

Category

FantasyViolence

Rating

TV-Y7

Violence

TV-MA

TV-14

TV-PG

Sexual Situation

Coarse Language

Suggestive Dialogue

TV-14,TV-PG

Note

Blocked sub rating will appear beside the main rating category in

[USTV Ratings Lock] menu.

You cannot block a sub rating (D, L, S orV) if the main rating is set to

[View]

Changing the category to [Block] or [View] automatically changes all its sub

ratings to the same ([Block] or [View]).

•

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Clock, Phase

PC Settings

This function lets you adjust the PC screen position, clock and

Use ◄/► to adjust [Clock] setting to stabilize

phase during PC input.

the PC screen and [Phase] setting to improve the clarity

of the PC screen.

1 Press MENU to display the main menu.

Cursor

2 Use ▲/▼ to select [Features], then press OK

Use ▲/▼ to select [PC Settings], then press OK

Clock

Adjust

Move

to decrease

setting value

to increase

setting value

4 Use ▲/▼ to select the setting you want to adjust, then

Phase

press OK

Adjust

Move

Auto Adjustment

Picture

Sound

Press MENU to exit.

Horizontal Position

Vertical Position

Clock

Setup

Note

Features

Language

You may not obtain an appropriate screen with

[Auto Adjustment] for some signals. In this case, adjust the settings manually.

•

Phase

Adjust [Phase] setting after [Clock] setting has been properly adjusted.

•

Adjust the setting.

Auto Adjustment

Use ▲/▼ to select [Adjust], then press OK.

Cancel

Adjust

Picture

Sound

To automatically synchronize the

phase and clock on the TV and PC.

Setup

Features

Language

• The horizontal/vertical position, clock and phase of the

PC screen are automatically adjusted.

Horizontal Position,Vertical Position

Use ◄/► to adjust.

Cursor ◄

Cursor ►

Horizontal Position

to move PC

screen left

to move PC

screen right

H. Position

Adjust

Move

Vertical Position

to move PC

screen down

to move PC

screen up

V. Position

Adjust

Move

Download from Www.Somanuals.com. All Manuals Search And Download.

AutoTV On

Fun-Link

This unit will turn on detected when the power on signal

is sent from your connected Fun-Link device.

Use ▲/▼ to select the desired setting, then press OK

This function allows you to operate the linked functions

between our brand devices with a Fun-Link feature and this

unit connecting through an HDMI cable.

1 Press MENU to display the main menu.

Picture

Sound

Off

2 Use ▲/▼ to select [Features], then press OK

3 Use ▲/▼ to select [Fun-Link], then press OK

When set to "On", TV and connected device

are turned on automatically.

Setup

Features

Language

Fun-Link Control

Auto Device Off

Auto TV On

Picture

Sound

Setup

This unit turns on automatically when you turn on

your connected Fun-Link device.

Device Control

Device List

Features

Language

Off

This unit stays off even if you turn on your

connected Fun-Link device.

Device Control

You can operate some functions such as disc playback or

call up the menu of the connected devices, by using this

unit’s remote control.

4 Use ▲/▼ to select the desired setting, then press OK

5 Adjust the following items.

Use ▲/▼ to select the desired setting, then press OK

Fun-Link Control

Set the Fun-Link [On] or [Off]

The following additional settings will be in gray when you

set to [Off]

Picture

Sound

Off

When set to "On", the connected device is

controlled using the remote control.

Setup

Use ▲/▼ to select the desired setting, then press OK

Features

Language

Picture

Sound

Off

When set to "On", Fun-Link functions are

enabled.

Setup

Features

Language

PLAY B/STOP C/FWD D/REV E/SKIP G/

SKIP H/PAUSE F/FUN-LINK OPTIONS

▲/▼/◄/►/OK/BACK

the Number buttons/RED/GREEN/BLUE/

YELLOW can be used to control your connected

Fun-Link devices by this unit's remote control

Off

Disables the device control.

Selects if you have connected an external device

that is compatible with the Fun-Link function.

Off

Device List

Disables all Fun-Link.

This function lets you see the product model number or

name of connected devices.

Auto Device Off

You can set your device to turn off by interlocking from

this unit’s power.

Use ▲/▼ to select the desired HDMI device listed on

theTV screen, then press OK.

Use ▲/▼ to select the desired setting, then press OK

Picture

Sound

HDMI1

HDMI2

NB530MGX

Sound

Off

MBP1100 / F7

Setup

When set to "On" and TV is turned off,

connected devices are turned off

automatically.

Setup

Features

Language

Features

Language

BACK

Select

Input Change

Back

Your connected Fun-Link device turns off

automatically when you turn off the unit.

6 Press MENU to exit.

Off

Your connected Fun-Link device stays on even if

you turn off the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Energy Saving Mode

Current Software Info

You can set whether the power consumption is saved or not.

This function shows what version of the software currently

used.

1 Press MENU to display the main menu.

2 Use ▲/▼ to select [Features], then press OK

Use ▲/▼ to select [Energy Saving Mode], then press OK

Use ▲/▼ to select the desired mode, then press OK

2 Use ▲/▼ to select [Features], then press OK

Use ▲/▼ to select [Current Software Info], then press

Conﬁrm the version of the software currently used.

Picture

Sound

Off

Setup

Back

When set to “On”, power consumption is reduced

by decreasing backlight brightness.

Features

Language

Sound

Setup

Release Version:

XXXXXXX_XXX_X_XXXX

Features

Language

Off

Reduces the power consumption.

The power consumption may possibly

exceed the limited requirement of the

ENERGY STAR^®qualification.

Press MENU to exit.

Location

When you select [Retail] store, the power consumption may

possibly exceed the limited requirement of the

ENERGY STAR^®qualiﬁcation.

1 Press MENU to display the main menu.

Use ▲/▼ to select [Features], then press OK

Use ▲/▼ to select [Location], then press OK

Use ▲/▼ to select the desired location, then press OK

Retail

Home

Sound

Location Home is recommended for

normal home use.

In the Retail Store mode, all settings are

fixed.

Setup

Features

Language

Press MENU to exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Troubleshooting Guide

If the unit does not perform properly when operated as instructed in this manual,

check the following chart and all connections once before calling for service.

Symptom

Remedy

•

Make sure the AC power cord is plugged in.

•

Make sure that the AC outlet supplies the proper voltage, plug another electrical

appliance into the AC outlet to ensure that AC outlet operates normally.

If a power failure occurs, unplug the AC power cord for 1 minute to allow the unit to

reset itself.

No power

•

Press only one button at a time. Do NOT press more than one button at the same time.

Ensure that no buttons on the remote are depressed and move freely.

Control button does not work.

•

Check whether the connection of the antenna, cable receiver or satellite box is

connected correctly.

Check whether all the cables to the unit are connected to the correct output jack of

your device like BD/DVD recorder.

•

Power is ON but no screen

image.

•

Make sure that the selected input mode is connected to the working input jack.

Check if your computer is NOT in sleep mode when the input mode of this unit is in PC

mode.Tap any key on the keyboard to wake up your computer.

•

Check if the power is on.

Check if the right input mode is selected.

Check whether all the cables to the unit are connected to the correct output jack of

your device like BD/DVD recorder.

View otherTV channels.The problem might be limited to the broadcasting station or

weak signal strength.

•

Turn off the unit and wait for about 1 minute, then turn on the unit again.

Check whether the connection of the antenna, cable receiver or satellite box is

connected correctly.

No picture or sound

•

Make sure that the selected input mode is connected to the working input jack.

Check if your computer is NOT in sleep mode when the input mode of this unit is in PC

mode.Tap any key on the keyboard to wake up your computer.

Make sure that the sound is not muted. Press MUTE so that the volume bar and current

volume level will appear on theTV screen.

•

Make sure that the volume is NOT set to [ ] or [Mute]. If so, use

VOL +/–

to adjust the

desired volume.

•

View otherTV channels.The problem might be limited to the broadcasting station.

Adjust [Color] in the main menu.

No color

Adjusted [Picture]

[Sound]

settings are not effective every

time the unit is turned on.

•

You must set [Home] in [Location].

p.31

➠

Otherwise, the settings you adjusted will not be memorized after you turn off the unit.

•

Electrical interference from nearby appliances may affect picture quality.

Adjust [Contrast] and [Brightness] in the main menu.

View otherTV channels.The problem might be limited to the broadcasting station or

weak signal strength.

Sound OK, picture poor

•

For the best picture quality, watch "High Definition" wide screen programs.

If the HD content is not available, watch "Standard Definition" programs instead.

View otherTV channels.The problem might be limited to the broadcasting station or

weak signal strength.

Check if the audio cable is connected in correctly.

Picture OK, sound poor

•

You may be getting interference from electrical appliances, automobiles, motorcycles or

ﬂuorescent lights.

Try moving the unit to another location to see if this is the cause of the problem.

You see a distorted picture or

hear an unusual sound.

•

Electrical interference from nearby appliances may affect picture quality.

View otherTV channels.The problem might be limited to the broadcasting station.

Ghosts, lines or streaks in picture

Download from Www.Somanuals.com. All Manuals Search And Download.

English

Symptom

Remedy

•

When the capabilities of the unit exceed the capabilities of the digital broadcasting, the

signal will be increased to match the capabilities of the display of the unit.This may cause

noise or trash.

You see "noise" or "trash" on the

screen.

Different color marks on theTV

screen

•

View otherTV channels.The problem might be limited to the broadcasting station,

missing data or pixelation.

•

This unit will memorize the volume level from the last time you adjusted it.

If the volume of the sound from another device is higher or lower, then the loudness will

change.

You switch to a different input

and the volume changes.

You switch to a different input

and the screen size changes.

•

This unit will memorize the viewing mode from the last time you used the particular

input modes.

•

If you are using the unit as a PC monitor, make sure that [Horizontal Position] and

[Vertical Position] in [PC Settings] are set correctly.

If you are watchingTV or using the CompositeVideo, S-Video, ComponentVideo or

HDMI with 480i Input, press FORMAT repeatedly to switch various screen modes.

The display image does not cover

the entire screen.

Captions are displayed as a white

box.

No caption is displayed in the

Closed Caption-supported

program.

•

Interference from buildings or weather conditions may cause captioning to be incomplete.

Broadcasting station may shorten the program to insert advertisement.

The closed caption decoder cannot read the information of the shortened program.

Black box is displayed on theTV

screen.

•

The text mode is selected for caption. Select [CC-1] [CC-2] [CC-3] [CC-4] or [Off]

Note

The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a ﬁxed point of blue, green or red.

This is not to be considered a defect in the LCD screen.

Some functions are not available in speciﬁc modes, but this is not a malfunction. Read the description in this manual for more details on correct operations.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

FAQ

Question

Answer

•

Check the antenna or cable connection to the main unit.

Check the batteries of the remote control.

Check if there is an obstacle between the infrared sensor window and the remote

control.

Test the signal output. If OK, then possible infrared sensor trouble.

•

[IR Signal Check]

p.35

My remote control does not

work.

What should I do?

➠

•

Aim the remote control directly at the infrared sensor window on the front of the unit.

Reduce the distance to the unit.

Re-insert the batteries with their polarities (+/– signs) as indicated.

When there is an infrared-equipped device such as PC near this unit, it may interrupt

the remote control signal of this unit.

Move the infrared-equipped device away from this unit, change the angle of the infrared

sensor or turn off the infrared communication function.

•

How come the Initial setup

appears every time I turn on

this unit?

•

Connect the RF coaxial cable to the unit directly and run the initial setup.

Make sure to complete the channel scan before turning off the unit.

•

Make sure [Autoprogram] has been completed.

p.19

➠

Autoprogram must be completed when you set up the unit for the ﬁrst time or move it

to a location where previously unavailable channels are broadcast.

The selected channel may not be broadcasting.

•

When [Autoprogram] is interrupted and not completed, some channels will not be

Why I cannot watch some RF

signalTV programs.

received. Make sure to complete.

The selected channel cannot be viewed by the [Child Lock] setting.

p.19

➠

•

p.27

➠

The unit requires some kind of antenna input.An indoor antenna

(VHF /UHF), an external antenna (VHF /UHF) or an RF coaxial cable from your wall

cable/satellite box needs to be plugged into the unit.

•

Check if the right input mode is selected by pressing SOURCE or using CH +/

[Switching Each Input Mode]

Check the antenna or cable connection to the unit.

When using the ComponentVideo Connection check that the Green (Y), Blue (Pb/Cb)

and Red (Pr/Cr) connectors are connected to their corresponding colored jacks on the

unit.

p.16

➠

How come there is no image

from the connected external

devices?

•

Many digital channels have alternate channel numbers.

The unit changes the numbers automatically to the ones signifying the broadcasting

station channel number.

Whenever I entered channel

number,

it changes automatically.

These basic numbers used for previous analog broadcasts.

(e.g., input ch#30 auto change to ch#6.1)

•

Captions that are delayed a few seconds behind the actual dialogue are common for live

broadcasts. Most captioning production companies can display a dialogue to maximum

of 220 words per minute. If a dialogue exceeds that rate, selective editing is used to

insure that the captions remain up-to date with the currentTV screen dialogue.

Why are captions not displayed

entirely?

Or, captions are delayed behind

the dialogue.

There is no clock function on this unit.

How can I set the clock ?

Download from Www.Somanuals.com. All Manuals Search And Download.

English

INFORMATION

Glossary

Maintenance

ATSC

Acronym that stands for AdvancedTelevision Systems Committee and

the name of the digital broadcasting standards.

Cabinet Cleaning

Wipe the front panel and other exterior surfaces of the

unit with a soft cloth immersed in lukewarm water and

wrung dry.

Never use a solvent or alcohol. Do not spray insecticide

liquid near the unit. Such chemicals may cause damage and

discoloration to the exposed surfaces.

•

Aspect Ratio

The width of aTV screen relative to its height. ConventionalTVs

are 4:3 (in other words, theTV screen is almost square); widescreen

models are 16:9 (theTV screen is almost twice as wide as its height).

ComponentVideo

This is a video signal format that conveys each of 3 principal colors

of light (red, blue and green) through different signal lines.This allows

the viewers to experience picture colors as original as it is.There are

several signal formats, includingY/Pb/Pr andY/Cb/Cr.

Panel Cleaning

Wipe the panel of the unit with a soft cloth. Before cleaning

the panel, disconnect the AC power cord.

Dolby Digital

The system developed by Dolby Laboratories to compress digital

sound. It offers stereo sound (2ch) or multi-channel audio.

HDMI

(High-Definition Multimedia Interface)

Interface that supports all uncompressed, digital audio/video formats

including set-top box, BD/DVD recorder or digital television, over a

single cable.

Servicing

Should your unit become inoperative, do not try to correct

the problem yourself.There are no user serviceable parts

inside.Turn off the unit, unplug the AC power cord and call

our toll free customer support line found on the cover of this

manual to locate an authorized service center.

HDTV (High DefinitionTV)

Ultimate digital format that produces high resolution and high picture

quality.

NTSC

IR Signal Check

If the remote control is not working properly, you can use a

digital camera (including a cellular phone with built-in camera)

to see if it is sending out an infrared signal.

Acronym that stands for NationalTelevision Systems Committee and

the name of analog broadcasting standards.

Off the air NTSC signals are no longer being sent by major

broadcasting stations in the USA.

PIN code

A stored 4-digit number that allows access to parental control features.

With a digital camera

(including built-in cell phone cameras):

Point the Digital Camera towards the remote

control infrared diode at the front of the

remote control. Press any button on the

remote control and look through the camera

display. If the infrared pulsating light appears

through the camera, the remote control is

sending out an IR signal.

SAP (Secondary Audio Program)

Second-audio channel delivered separately from main-audio channel.

This audio channel is used as an alternate in bilingual broadcasting.

SDTV (Standard DefinitionTV)

Standard digital format that is similar to the NTSC picture quality.

S-Video

Offers higher quality images by delivering each signal, color (c) and

luminance (y) independently of each other through a single cable.

Download from Www.Somanuals.com. All Manuals Search And Download.

General Speciﬁcations

Other Speciﬁcations

TV format

ATSC/NTSC-M TV standard

Terminals

Closed caption system

Antenna Input VHF / UHF / CATV

75Ω unbalanced (F-type)

500mV rms

§15.122/FCC (digital CC)

§15.119/FCC (analog CC)

Audio Input

CompositeVideo Input

RCA jack x 1

RCA jack (L/R) x 6

Channel coverage (ATSC/NTSC)

Terrestrial DTV (ATSC)

VHF 2~13

1V p-p (75Ω)

S-Video Input Mini DIN 4 pin jack x 1

1V p-p (75Ω)

UHF 14~51 each channel has e.g.)

2.1~2.9, 3.1~3.9, etc.

286mV p-p (75Ω)

ComponentVideo Input

Terrestrial Analog (NTSC)

RCA jack x 3

1V p-p (75Ω)

VHF 2~13

Pb/Cb 700mV p-p (75Ω)

Pr/Cr 700mV p-p (75Ω)

UHF 14~69

CATV

2~13, A~W,

HDMI Input

PC Input

HDMI 19pin x 2

W+1~W+94 (analog W+1~W+84),

A-5~A-1, 5A

D-Sub 15pin 1(RGB)

Tuning system

Channel access

Channel frequency synthesized tuning

system

Mini jack ø3.5mm 1(Audio)

Coaxial Digital Audio Output

Direct access keyboard,

Programmable scan, and up/down

RCA jack x 1

500mV p-p (75Ω)

Headphone:

inches 1(3.5mm)

Remote control

Digital encoded infrared light system

Electrical Speciﬁcation

Operating temperature

41°F (5°C) to 104°F (40°C)

Audio Output

3W, 8Ω x 2

Power requirements

120V~ AC +/- 10%, 60Hz +/- 0.5%

For 22MF330B

LCD

22inches (21.6 inches measured diagonally)

Power consumption (maximum)

67 W

Dimensions

Width 21.4 inches(542.8mm) 21.4 inches(542.8mm)

Height 14.8 inches(373.6mm) 16.2 inches(411.2mm)

Depth 4.0 inches(100.2mm) 8.3 inches(210.0mm)

9.71 lbs. (4.40kg)

10.37 lbs. (4.70kg)

Weight

For 19MF330B

LCD

19 inches (18.5 inches measured diagonally)

Power consumption (maximum)

51 W

Dimensions

Width 18.8 inches(477.5mm) 18.8 inches(477.5mm)

Height 13.1 inches(330.4mm) 14.5 inches(365.8mm)

Depth 3.7 inches(91.7mm)

8.3 inches(210.0mm)

8.60 lbs. (3.90kg)

7.94 lbs. (3.60kg)

Weight

•

Designs and speciﬁcations are subject to change without

notice and without our legal obligation.

If there is a discrepancy between languages, the default

language will be English.

Download from Www.Somanuals.com. All Manuals Search And Download.

English

LIMITED WARRANTY

( )

(

)

NINETY 90 DAY LABOR / ONE 1 YEAR PARTS

WARRANTY COVERAGE:

This warranty obligation is limited to the terms as set forth

below.

mission, or (d) if any serial number has been removed or defaced,

or (e) product, accessories or consumables sold “AS IS” without

warranty of any kind by including refurbished product sold “AS

IS” by some retailers.

WHO IS COVERED:

This product warranty is issued to the original purchaser or the

person receiving the product as a gift against defects in materials

and workmanship as based on the date of original purchase

(“Warranty Period”) from an Authorized Dealer. The original

sales receipt showing the product name and the purchase date

from an authorized retailer is considered such proof.

This Limited Warranty does not cover:

•

Shipping charges to return defective product.

Labor charges for installation or setup of the product, adjust-

ment of customer controls on the product, and installation or

repair of antenna/signal source systems outside of the product.

Product repair and/or part replacement because of improper

installation or maintenance, connections to improper voltage

supply, power line surge, lightning damage, retained images or

•

WHAT IS COVERED:

This warranty covers new products if a defect in material or

workmanship occurs and a valid claim is received within the

Warranty Period. At its option, the company will either (1)

repair the product at no charge, using new or refurbished

replacement parts, or (2) exchange the product with a product

that is new or which has been manufactured from new, or ser-

viceable used parts and is at least functionally equivalent or most

comparable to the original product in current inventory, or (3)

refund the original purchase price of the product.

tent for extended periods, product cosmetic appearance items

due to normal wear and tear, unauthorized repair or other

cause not within the control of the company.

Damage or claims for products not being available for use, or

for lost data or lost software.

Damage from mishandled shipments or transit accidents when

returning product.

•

Replacement products or parts provided under this warranty are

covered against defects in materials and workmanship from the

date of the replacement or repair for ninety (90) days or for the

remaining portion of the original product’s warranty, whichever

provides longer coverage for you. When a product or part is

exchanged, any replacement item becomes your property and the

replaced item becomes company property. When a refund is

given, your product becomes company property.

it to operate in any country other than the country for which

it was designed, manufactured, approved and/or authorized, or

•

A product used for commercial or institutional purposes

(including but not limited to rental purposes).

can be provided.

Failure to operate per Owner’s Manual.

Note: Any product sold and identified as refurbished or

renewed carries a ninety (90) day limited warranty.

TO OBTAIN ASSISTANCE…

Contact the Customer Care Center at:

1-866-341-3738

Replacement product can only be sent if all warranty

requirements are met. Failure to follow all requirements

can result in delay.

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS

WARRANTY IS THE EXCLUSIVE REMEDY FOR THE CON-

SUMER, WITH THE ISSUING COMPANY NOT LIABLE FOR

ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR

BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON

THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY

APPLICABLE LAW, ANY IMPLIED WARRANTY OF MER-

CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

ON THIS PRODUCT IS LIMITED IN DURATION TO THE

DURATION OF THIS WARRANTY.

WHAT IS NOT COVERED - EXCLUSIONS AND LIMI-

TATIONS:

This Limited Warranty applies only to new company manufac-

to any hardware product or any software, even if packaged or

sold with the product, as manufacturers, suppliers, or publishers

may provide a separate warranty for their own products pack-

aged with the bundled product.

The company is not liable for any damage to or loss of any pro-

grams, data, or other information stored on any media contained

within the product, or other additional product or part not cov-

ered by this warranty. Recovery or reinstallation of programs,

data or other information is not covered under this Limited

Warranty.

Some states do not allow the exclusions or limitation of inciden-

tal or consequential damages, or allow limitations on how long an

implied warranty lasts, so the above limitations or exclusions may

not apply to you.

This warranty does not apply (a) to damage caused by accident,

abuse, misuse, neglect, misapplication, or non-supplied product,

(b) to damage caused by service performed by anyone other than

company approved Authorized Service Location, (c) to a product

FUNAI CORPORATION, Inc. 19900 Van Ness Avenue, Torrance, CA 90501

Printed in China

Download from Www.Somanuals.com. All Manuals Search And Download.

La Crosse Technology Weather Radio TX62U IT User Manual
La Crosse Technology Weather Radio WS 9060U IT User Manual
Land Pride Tiller RTA2064 User Manual
LG Electronics Dishwasher LSDF9962ST User Manual
LG Electronics DVD Recorder RH2T160 User Manual
LSI Switch SAS6160 User Manual
Lumiscope Thermometer 2215 User Manual
Melissa Toaster 021 028 User Manual
MGE UPS Systems Power Supply Galaxy 3000 User Manual
Microsoft Video Games X08 40995 User Manual