G43Twins-FullHD
User Manual
Version 1.2
Published September 2008
Copyright©2008 ASRock INC. All rights reserved.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1 Introduction ................................................... 5
1.1 Package Contents .......................................................... 5
1.2 Specifications ................................................................. 6
1.3 Minimum Hardware Requirement Table for Windows®
VistaTM Premium 2008 and Basic Logo......................... 10
1.4 Minimum Hardware Requirement for Full HD 1080p Blu-ray
(BD) / HD-DVD Playback Support .................................. 11
1.5 Passed Full HD 1080p Blu-ray (BD) / HD-DVD Films in
Our Lab Test .................................................................. 11
1.6 Motherboard Layout ...................................................... 12
1.7 ASRock GLAN_8CH I/O ................................................. 13
1.8 ASRock DVI_DisplayPort Specifications ....................... 14
2 Installation...................................................... 15
2.1 Screw Holes ................................................................. 15
2.2 Pre-installation Precautions ........................................... 15
2.3 CPU Installation .............................................................. 16
2.4 Installation of Heatsink and CPU fan ............................. 18
2.5 Installation of Memory Modules (DIMM)......................... 19
2.6 Expansion Slots (PCI and PCI Express Slots) ..................... 21
2.7 Installation of ASRock DVI_DisplayPort Card ................ 22
2.8 Jumpers Setup .............................................................. 24
2.9 Onboard Headers and Connectors .............................. 26
2.10 SATAII Hard Disk Setup Guide ....................................... 30
2.11 Serial ATA (SATA) / Serial ATAII (SATAII) Hard Disks
Installation ...................................................................... 31
2.12 Hot Plug Function for SATA / SATAII HDDs .................. 31
2.13 SATA / SATAII HDD Hot Plug Feature and Operation
Guide .............................................................................. 32
2.14 Driver Installation Guide ................................................. 34
2.15 Installing Windows® 2000 / XP / XP 64-bit / VistaTM
/
VistaTM 64-bit Without RAID Functions ........................... 34
2.15.1 Installing Windows® 2000 / XP / XP 64-bit Without
RAID Functions ................................................... 34
2.15.2 Installing Windows® VistaTM / VistaTM 64-bit Without
RAID Functions ................................................... 35
2.16 Untied Overclocking Technology ................................... 36
3 BIOS SETUP UTILITY........................................... 37
3.1 Introduction .................................................................... 37
3.1.1 BIOS Menu Bar .................................................... 37
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1.2 Navigation Keys ................................................... 38
3.2 Main Screen................................................................... 38
3.3 Smart Screen ................................................................ 39
3.4 Advanced Screen ......................................................... 40
3.4.1 CPU Configuration................................................ 40
3.4.2 Chipset Configuration .......................................... 42
3.4.3 ACPI Configuration ............................................... 46
3.4.4 IDE Configuration ................................................. 47
3.4.5 PCIPnP Configuration ........................................... 49
3.4.6 Floppy Configuration ........................................... 50
3.4.7 Super IO Configuration ........................................ 50
3.4.8 USB Configuration ............................................... 51
3.5 Hardware Health Event Monitoring Screen .................. 52
3.6 Boot Screen................................................................... 53
3.5.1 Boot Settings Configuration.................................. 53
3.7 Security Screen ............................................................ 54
3.8 Exit Screen .................................................................... 55
4 Software Support ........................................... 56
4.1 Install Operating System ............................................... 56
4.2 Support CD Information ................................................. 56
4.2.1 Running Support CD ............................................ 56
4.2.2 Drivers Menu ........................................................ 56
4.2.3 Utilities Menu ........................................................ 56
4.2.4 Contact Information .............................................. 56
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Thank you for purchasing ASRock G43Twins-FullHD motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control. It de-
livers excellent performance with robust design conforming to ASRock’s commit-
ment to quality and endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by-step
guide to the hardware installation. Chapter 3 and 4 contain the configuration guide to
BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might
be updated, the content of this manual will be subject to change without
notice. In case any modifications of this manual occur, the updated
version will be available on ASRock website without further notice. You
may find the latest VGA cards and CPU support lists on ASRock website
If you require technical support related to this motherboard, please visit
our website for specific information about the model you are using.
1.1 Package Contents
ASRock G43Twins-FullHD Motherboard
(Micro ATX Form Factor: 9.6-in x 9.6-in, 24.4 cm x 24.4 cm)
ASRock G43Twins-FullHD Quick Installation Guide
ASRock G43Twins-FullHD Support CD
One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable
One Ribbon Cable for a 3.5-in FloppyDrive
One Serial ATA (SATA) Data Cable (Optional)
One Serial ATA (SATA) HDDPower Cable (Optional)
One “ASRock GLAN_8CH I/O” I/O Panel Shield
One ASRock DVI_DisplayPort Card
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2
S
p
e
c
i
f
i
c
a
t
i
o
n
s
Platform
CPU
- Micro ATX Form Factor: 9.6-in x 9.6-in, 24.4 cm x 24.4 cm
- Solid Capacitor for CPU power
- LGA 775 for Intel® CoreTM 2 Extreme / CoreTM 2 Quad / CoreTM
2 Duo / Pentium® Dual Core / Celeron® Dual Core / Celeron®,
supporting Penryn Quad Core Yorkfield and Dual Core
Wolfdale processors
- Supports FSB1333/1066/800 MHz
- Supports Hyper-Threading Technology (see CAUTION 1)
- Supports Untied Overclocking Technology (see CAUTION 2)
- Supports EM64T CPU
Chipset
Memory
-Northbridge: Intel® G43
- Southbridge: Intel® ICH10
-Dual Channel DDR3/DDR2 Memory Technology
(see CAUTION 3)
- 2 x DDR3 DIMM slots
- SupportDDR3 1066/800 non-ECC, un-buffered memory
(see CAUTION 4)
- Max. capacity of system memory: 4GB (see CAUTION 5)
- 2 x DDR2 DIMM slots
- SupportDDR2 1066/800/667 non-ECC, un-buffered memory
(see CAUTION 4)
- Max. capacity of system memory: 8GB (see CAUTION 5)
- 1 x PCI Express 2.0 x16 slot (green @ x16 mode)
- 1 x PCI Express x1 slot
Expansion Slot
Graphics
- 2 x PCI slots
- Intel® Graphics Media Accelerator X4500
- Pixel Shader 4.0, DirectX 10
- Max. shared memory 352MB (see CAUTION 6)
- Three VGA Output options: D-Sub, DVI-D and DisplayPort with
ASRock DVI_DisplayPort Card (see CAUTION 7)
- Supports DVI-D and DisplayPort with ASRock DVI_DisplayPort
Card
- Supports HDCP function with ASRock DVI_DisplayPort Card
- Supports Full HD 1080p Blu-ray (BD) / HD-DVD playback with
ASRock DVI_DisplayPort Card (see CAUTION 8)
- 7.1 CH Windows® VistaTM Premium Level HDAudio
(ALC888 Audio Codec)
Audio
LAN
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111B/RTL8111C
- Supports Wake-On-LAN
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel I/O
ASRock GLAN_8CH I/O
- 1 x PS/2 Mouse Port
- 1 x PS/2 Keyboard Port
- 1 x VGA Port
- 6 x Ready-to-Use USB 2.0 Ports
- 1 x RJ-45 LAN Port
- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/
Line in/Front Speaker/Microphone (see CAUTION 9)
- 6 x SATAII 3.0Gb/s connectors, support NCQ, AHCI and “Hot
Plug” functions (see CAUTION 10)
- 1 x ATA133 IDE connector (supports 2 x IDE devices)
- 1 x Floppy connector
Connector
- 1 x IR header
- 1 x COM port header
- CPU/Chassis FAN connector
- 24 pin ATX power connector
- 4 pin 12V power connector
- CD in header
- Front panel audio connector
- 2 x USB 2.0 headers (support 4 USB 2.0 ports)
(see CAUTION 11)
- 1 x WiFi/E header (see CAUTION 12)
- 8Mb AMI BIOS
BIOS Feature
- AMI Legal BIOS
- Supports “Plug and Play”
- ACPI 1.1 Compliance Wake Up Events
- Supports jumperfree
- AMBIOS 2.3.1 Support
- CPU, DRAM, NB, SB, VTT Voltage Multi-adjustment
- Supports I. O. T. (Intelligent Overclocking Technology)
- Supports Smart BIOS
Support CD
- Drivers, Utilities, AntiVirus Software (Trial Version)
- ASRock OC Tuner (see CAUTION 13)
- Hybrid Booster:
Unique Feature
- CPU Frequency Stepless Control (see CAUTION 14)
- ASRock U-COP (see CAUTION 15)
- Boot Failure Guard (B.F.G.)
- CPU Temperature Sensing
Hardware
Monitor
- Chassis Temperature Sensing
- CPU Fan Tachometer
- Chassis Fan Tachometer
- CPU Quiet Fan
7
Download from Www.Somanuals.com. All Manuals Search And Download.
- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore
- Microsoft® Windows® 2000 / XP / XP 64-bit / VistaTM
VistaTM 64-bit compliant (see CAUTION 16)
- FCC, CE, WHQL
OS
/
Certifications
WARNING
Please realize that there is a certain risk involved with overclocking, including adjusting
the setting in the BIOS, applying Untied Overclocking Technology, or using the third-
party overclocking tools. Overclocking may affect your system stability, or even
cause damage to the components and devices of your system. It should be done at
your own risk and expense. We are not responsible for possible damage caused by
overclocking.
CAUTION!
1. About the setting of “Hyper Threading Technology”, please check page 41.
2. This motherboard supports Untied Overclocking Technology. Please read
“Untied Overclocking Technology” on page 36 for details.
3. This motherboard supports Dual Channel Memory Technology. Before
you implement Dual Channel Memory Technology, make sure to read
the installation guide of memory modules on page 19 for proper installation.
4. Please check the table below for the CPU FSB frequency and its
corresponding memory support frequency.
CPU FSB Frequency
1333
Memory Support Frequency
DDR2 667, DDR2 800, DDR2 1066,
DDR3 800, DDR3 1066
DDR2 667, DDR2 800, DDR2 1066,
DDR3 800, DDR3 1066
DDR2 667, DDR2 800,
1066
800
DDR3 800
*
*
DDR2 1066 memory modules will operate in overclocking mode.
If you adopt a DDR2 1066 memory module on this motherboard,
you need to adjust the jumpers. Please refer to page 24 for proper
jumper settings.
5. Due to the operating system limitation, the actual memory size may be
less than 4GB for the reservation for system usage under Windows® XP
and Windows® VistaTM. For Windows® XP 64-bit and Windows® VistaTM
64-bit with 64-bit CPU, there is no such limitation.
6. The maximum shared memory size is defined by the chipset vendor and
is subject to change. Please check Intel® website for the latest information.
7. This motherboard supports three VGA output options: D-Sub, DVI-D and
DisplayPort. D-Sub port is on the I/O panel. DVI-D and DisplayPort are
supported when you install the bundled ASRock DVI_DisplayPort Card on
PCIE2 (green) slot.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Full HD 1080p Blu-ray (BD) / HD-DVD playback is supported only when you
install ASRock DVI_DisplayPort Card. Full HD 1080p Blu-ray (BD) / HD-DVD
playback support requires the proper hardware configuration. Please refer to
page11 for the minimum hardware requirement and the passed Full HD 1080p
Blu-ray (BD) / HD-DVD films in our lab test.
9. For microphone input, this motherboard supports both stereo and mono
modes. For audio output, this motherboard supports 2-channel, 4-
channel, 6-channel, and 8-channel modes. Please check the table on
page 13 for proper connection.
10. Before installing SATAII hard disk to SATAII connector, please read the
“SATAII Hard Disk Setup Guide” on page 30 to adjust your SATAII hard disk
drive to SATAII mode. You can also connect SATA hard disk to SATAII
connector directly.
11. Power Management for USB 2.0 works fine under Microsoft® Windows®
VistaTM 64-bit / VistaTM / XP 64-bit / XP SP1 or SP2 / 2000 SP4.
12. WiFi/E header supports WiFi+AP function with ASRock WiFi-802.11g or
WiFi-802.11n module, an easy-to-use wireless local area network
(WLAN) adapter. It allows you to create a wireless environment and
enjoy the convenience of wireless network connectivity. Please visit our
website for the availability of ASRock WiFi-802.11g or WiFi-802.11n
13. It is a user-friendly ASRock overclocking tool which allows you to surveil
your system by hardware monitor function and overclock your hardware
devices to get the best system performance under Windows®
environment. Please visit our website for the operation procedures of
14. Although this motherboard offers stepless control, it is not recommended
to perform over-clocking. Frequencies other than the recommended CPU
bus frequencies may cause the instability of the system or damage the
CPU.
15. While CPU overheat is detected, the system will automatically shutdown.
Before you resume the system, please check if the CPU fan on the
motherboard functions properly and unplug the power cord, then plug it
back again. To improve heat dissipation, remember to spray thermal
grease between the CPU and the heatsink when you install the PC system.
16. AHCI function is not supported under Windows® 2000 OS. It is recom-
mended to use IDE mode under Windows® 2000. Please refer to page 47
for detailed setup.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3
M
i
n
i
m
u
m
H
a
r
d
w
a
r
e
R
e
q
u
i
r
e
m
e
n
t
T
a
b
l
e
f
o
r
Windows® VistaTM Premium 2008 and Basic Logo
For system integrators and users who purchase this motherboard and
plan to submit Windows® VistaTM Premium 2008 and Basic logo, please
follow below table for minimum hardware requirements.
CPU
Celeron 420
Memory
512MB x 2 Dual Channel (Premium)
512MB Single Channel (Basic)
256MB x 2 Dual Channel (Basic)
DX10 with WDDM Driver
VGA
* If you plan to use onboard VGA to submit Windows® VistaTM logo, please keep the
default setting of “DVMT Mode Select” option under BIOS.
* If you plan to use external graphics card on this motherboard, please refer to
* After June 1, 2008, all Windows® VistaTM systems are required to meet above
minimum hardware requirements in order to qualify for Windows® VistaTM
Premium 2008 logo.
1 0
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4
M
i
n
i
m
u
m
H
a
r
d
w
a
r
e
R
e
q
u
i
r
e
m
e
n
t
f
o
r
F
u
l
l
H
D
1
0
8
0
p
Blu-ray (BD) / HD-DVD Playback Support
Full HD1080p Blu-ray (BD) / HD-DVDplayback support on this motherboard
requires the proper hardware configuration. Please refer to below table
for the minimum hardware requirement.
CPU
Intel® E1200
VGA
G43 onboard DX10 VGA
Memory
DDR2 800 1GB x 2
Suggested OS
Playback Software
Windows® VistaTM or Windows® VistaTM 64
CyberLink PowerDVD8 with patch 1830U
* Please set up BIOS option PAVP Lite mode enabled.
1.5 Passed Full HD 1080p Blu-ray (BD) / HD-DVD Films
in Our Lab Test
DVD
Film Name
Format
Type
Producer
Blu-ray SWORDFISH
VC-1
WB
DVD
UNDERWORLD EVOLUTION
MPEG-2
MPEG-4
MPEG-4
SONY
SONY
FOX
CASINO ROYALE
THE LEAGUE OF
EXTRAORDINARY GENTLEMEN
X-MEN III
MPEG-4
VC-1
FOX
HD-
DVD
KING KONG
UNIVERSAL
WEA
NEW ORLEANS CONCERT
MPEG-2
1 1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.6 Motherboard Layout
1
3
4
2
5
24.4cm (9.6 in)
1
PS2_USB_PWR1
34
ATX12V1
6
7
33
32
USB 2.0
T: USB4
B: USB5
USB 2.0
T: USB2
B: USB3
FSB1
1
IDE1
USB 2.0
T: USB0
B: USB1
Top:
RJ-45
FSB3
FSB2
1
1
31
30
Intel
G43
Chipset
LAN
PHY
PCIE1
1
8
9
CMOS
Battery
29
28
CLRCMOS1
CHA_FAN1
PCIE2
10
11
12
27
PCI Express 2.0
1
8Mb
BIOS
IR1
Intel
ICH10
PCI1
CD1
26
25
1
SATAII_3
SATAII_5
HD_AUDIO1
SPEAKER1
PCI2
1
13
AUDIO
CODEC
SATAII_6
SATAII_4
COM1
1
FLOPPY1
WIFI/E
1
1
1
USB6_7
USB8_9
14
15
16
17
20 19 18
22
21
24
23
1
2
3
4
PS2_USB_PWR1 Jumper
775-Pin CPU Socket
17 USB 2.0 Header (USB8_9, Blue)
18 Chassis Speaker Header (SPEAKER 1)
19 USB 2.0 Header (USB6_7, Blue)
20 Flash Memory
Clear CMOS Jumper (CLRCMOS1)
2 x 240-pin DDR2 DIMM Slots
(Dual Channel A: DDRII_1, DDRII_2; Yellow)
2 x 240-pin DDR2 DIMM Slots
21 COM Port Header (COM1)
22 Floppy Connector (FLOPPY1)
23 WiFi/E Header (WIFI/E)
5
(Dual Channel B: DDR3_A1, DDR3_B1; Green)
ATX Power Connector (ATXPWR1)
IDE1 Connector (IDE1, Blue)
6
7
8
9
24 PCI Slots (PCI1 - 2)
25 Front Panel Audio Header (HD_AUDIO1)
26 Internal Audio Connector: CD1 (Black)
27 Infrared Module Header (IR1)
28 PCI Express 2.0 x16 Slot (PCIE2; Green)
29 PCI Express x1 Slot (PCIE1; White)
30 North Bridge Controller
South Bridge Controller
Chassis Fan Connector (CHA_FAN1)
10 System Panel Header (PANEL1)
11 Secondary SATAII Connector (SATAII_2)
12 Primary SATAII Connector (SATAII_1)
13 Third SATAII Connector (SATAII_3)
14 Fourth SATAII Connector (SATAII_4)
15 Sixth SATAII Connector (SATAII_6)
16 Fifth SATAII Connector (SATAII_5)
31 FSB2 / FSB3 Jumpers
32 FSB1 Jumper
33 CPU Fan Connector (CPU_FAN1)
34 ATX 12V Connector (ATX12V1)
1 2
Download from Www.Somanuals.com. All Manuals Search And Download.
1.7
A
S
R
o
c
k
G
L
A
N
_
8
C
H
I
/
O
2
1
3
6
7
8
4
5
12
13
11
9
10
1
PS/2 Mouse Port (Green)
LAN RJ-45 Port
8
Microphone (Pink)
USB 2.0 Ports (USB01)
2
3
9
Side Speaker (Gray)
Rear Speaker (Black)
Central / Bass (Orange)
Line In (Light Blue)
Front Speaker (Lime)
10 USB 2.0 Ports (USB23)
11 USB 2.0 Ports (USB45)
12 VGA Port
4
5
6
13 PS/2 Keyboard Port (Purple)
* 7
* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.
See the table below for connection details in accordance with the type of speaker you use.
TABLE for Audio Output Connection
Audio Output ChannelsFront Speaker Rear Speaker
Central / Bass Side Speaker
(No. 7)
(No. 4)
(No. 5)
(No. 3)
2
4
6
8
V
V
V
V
--
V
V
V
--
--
V
V
--
--
--
V
To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. After restarting your computer, you will find “Mixer” tool on your system.
Please select “Mixer ToolBox”
, click “Enable playback multi-streaming”, and click
“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA
Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA
Audio 2nd output” to use front panel audio.
1 3
Download from Www.Somanuals.com. All Manuals Search And Download.
1.8
A
S
R
o
c
k
D
V
I
_
D
i
s
p
l
a
y
P
o
r
t
C
a
r
d
S
p
e
c
i
f
i
c
a
t
i
o
n
s
DisplayPort is a digital display interface standard put forth by the Video Electronics
Standards Association (VESA). It defines a new license-free, royalty-free, state-of-the-
art digital audio/video interconnect, and it is intended to be used primarily between a
computer and its display monitor, or a computer and a home-theater system.
ASRock DVI_DisplayPort Card is based on PCI Express x16 interface, and it supports
all mandatory features of DisplayPort version 1.1 specifications and the following
optional features:
- Equipped with one DVI-D connector and one DisplayPort connector
- Mode support up to 1920x1200@60Hz (WUXGA) for DVI-D and
2560x1600@60Hz (WQXGA) for DisplayPort and 1080p@60Hz
- Supports the Auxiliary Channel (AUX CH)
- Open standard supported by VESA, royalty and license free
- Compatible with HDMI via DVI to HDMI dongle
- Scalable lanes (1, 2, or 4 diff. pairs) unidirectional, RGB, YCbCr444
- (ANSI) 8b/10b encoding
- Fixed Link Speeds: 2.7Gbps or 1.62Gbps
- Supports HDCP function
1 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
This is a Micro ATX form factor (9.6" x 9.6", 24.4 x 24.4 cm) motherboard. Before you
install the motherboard, study the configuration of your chassis to ensure that the
motherboard fits into it.
Make sure to unplug the power cord before installing or removing the
motherboard. Failure to do so may cause physical injuries to you and
damages to motherboard components.
2.1 Screw Holes
Place screws into the holes indicated by circles to secure the motherboard to the
chassis.
Do not over-tighten the screws! Doing so may damage the motherboard.
2.2 Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any component.
2. To avoid damaging the motherboard components due to static electricity, NEVER
place your motherboard directly on the carpet or the like. Also remember to use
a grounded wrist strap or touch a safety grounded object before you handle
components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded antistatic pad or
in the bag that comes with the component.
Before you install or remove any component, ensure that the power is
switched off or the power cord is detached from the power supply.
Failure to do so may cause severe damage to the motherboard, peripherals,
and/or components.
1 5
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 CPU Installation
For the installation of Intel 775-LAND CPU,
please follow the steps below.
775-Pin Socket Overview
Before you insert the 775-LAND CPU into the socket, please check if
the CPU surface is unclean or if there is any bent pin on the socket.
Do not force to insert the CPU into the socket if above situation is
found. Otherwise, the CPU will be seriously damaged.
Step 1. Open the socket:
Step 1-1. Disengaging the lever by depressing
down and out on the hook to clear
retention tab.
Step 1-2. Rotate the load lever to fully open po-
sition at approximately 135 degrees.
Step 1-3. Rotate the load plate to fully open po-
sition at approximately 100 degrees.
Step 2. Insert the 775-LAND CPU:
Step 2-1. Hold the CPU by the edges where are
marked with black lines.
Step 2-2. Orient the CPU with IHS (Integrated
Heat Sink) up. Locate Pin1 and the two
orientation key notches.
Pin1
Pin1
alignment key
alignment key
orientation
key notch
orientation
key notch
775-PinSocket
775-LAND CPU
1 6
Download from Www.Somanuals.com. All Manuals Search And Download.
For proper inserting, please ensure to match the two orientation key
notches of the CPU with the two alignment keys of the socket.
Step 2-3. Carefully place the CPU into the socket
by using a purely vertical motion.
Step 2-4. Verify that the CPU is within the socket
and properly mated to the orient keys.
Step 3. Remove PnP Cap (Pick and Place Cap):
Use your left hand index finger and thumb to
support the load plate edge, engage PnP cap
with right hand thumb and peel the cap from the
socket while pressing on center of PnP cap to
assist in removal.
1. It is recommended to use the cap tab to handle and avoid kicking
off the PnP cap.
2. This cap must be placed if returning the motherboard for after
service.
Step 4. Close the socket:
Step 4-1. Rotate the load plate onto the IHS.
Step 4-2. While pressing down lightly on load
plate, engage the load lever.
Step 4-3. Secure load lever with load plate tab
under retention tab of load lever.
1 7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4
I
n
s
t
a
l
l
a
t
i
o
n
o
f
C
P
U
F
a
n
a
n
d
H
e
a
t
s
i
n
k
This motherboard is equipped with 775-Pin socket that supports Intel 775-LAND CPU.
Please adopt the type of heatsink and cooling fan compliant with Intel 775-LAND CPU
to dissipate heat. Before you installed the heatsink, you need to spray thermal
interface material between the CPU and the heatsink to improve heat dissipation.
Ensure that the CPU and the heatsink are securely fastened and in good contact with
each other. Then connect the CPU fan to the CPU_FAN connector (CPU_FAN1, see
page 12, No. 33).
For proper installation, please kindly refer to the instruction manuals of
your CPU fan and heatsink.
Below is an example to illustrate the installation of the heatsink for 775-LAND CPU.
Step 1. Apply thermal interface material onto center
of IHS on the socket surface.
Step 2. Place the heatsink onto the socket. Ensure
fan cables are oriented on side closest to the
CPU fan connector on the motherboard
(CPU_FAN1, see page 12, No. 33).
Step 3. Align fasteners with the motherboard
throughholes.
Step 4. Rotate the fastener clockwise, then press
down on fastener caps with thumb to install
and lock. Repeat with remaining fasteners.
If you press down the fasteners without rotating them clockwise,
the heatsink cannot be secured on the motherboard.
Step 5. Connect fan header with the CPU fan
connector on the motherboard.
Step 6. Secure excess cable with tie-wrap to ensure
cable does not interfere with fan operation or
contact other components.
1 8
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 Installation of Memor
y
M
o
d
u
l
e
s
(
D
I
M
M
)
This motherboard provides two 240-pinDDR2 (DoubleData Rate 2)DIMM slots and
two 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel
Memory Technology. For dual channel configuration, you always need to install
identical (the same brand, speed, size and chip-type) DDR2/DDR3 DIMM pair in
the slots of the same color. In other words, you have to install identical DDR2
DIMM pair in Dual Channel A (DDRII_1 and DDRII_2; Yellow slots; see p.12 No.
4) or identical DDR3 DIMM pair in Dual Channel B (DDR3_A1 and DDR3_B1;
Green slots; see p.12 No.5), so that Dual Channel Memory Technology can be
activated. You may refer to the Dual Channel Memory Configuration Table below.
Dual Channel DDR2 Memory Configurations
(DS: Double Side, SS: Single Side)
DDRII_1
DDRII_2
(Yellow Slot) (Yellow Slot)
2 memory modules SS
2 memory modules DS
SS
DS
Dual Channel DDR3 Memory Configurations
(DS: Double Side, SS: Single Side)
DDR3_A1
DDR3_B1
(Green Slot) (Green Slot)
2 memory modules SS
2 memory modules DS
SS
DS
1. If you want to install two memory modules, for optimal compatibility
and reliability, it is recommended to install them in the slots of the
same color. In other words, install them in the set of yellow slots
(DDRII_1 and DDRII_2), or in the set of green slots
(DDR3_A1 and DDR3_B1).
2. If you install only one memory module or two non-identical memory
modules, it is unable to activate the Dual Channel Memory Technology.
3. It is not allowed to install a DDR3 memory module into DDR2 slot or
install a DDR2 memory module into DDR3 slot; otherwise, this
motherboard and DIMM may be damaged.
4. DDR2 and DDR3 memory modules cannot be installed on this
motherboard at the same time.
1 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing a DIMM
Please make sure to disconnect power supply before adding or
removing DIMMs or the system components.
Step 1. Unlock a DIMM slot by pressing the retaining clips outward.
Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break
on the slot.
notch
break
notch
break
The DIMM only fits in one correct orientation. It will cause permanent
damage to the motherboard and the DIMM if you force the DIMM into the slot
at incorrect orientation.
Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully
snap back in place and the DIMM is properly seated.
2 0
Download from Www.Somanuals.com. All Manuals Search And Download.
2.6 Expansion Slots (PCI and PCI Express Slots)
There are 2 PCI slots and 2 PCI Express slots on this motherboard.
PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
PCIE slots:
PCIE1 (PCIE x1 slot; White) is used for PCI Express cards with x1 lane
width cards, such as Gigabit LAN card, SATA2 card, etc.
PCIE2 (PCIE x16 slot; Green) is used for PCI Express cards with x16
lane width graphics cards. If you want this motherboard to support DVI-D
and DisplayPort, please install ASRock DVI_DisplayPort Card on this
slot.
If you install the add-on PCI Express VGA card to PCIE2 (PCIE x16 slot),
the onboard VGA will be disabled. If you install the add-on PCI Express
VGA card to PCIE2 (PCIE x16 slot) and adjust the BIOS options “Primary
Graphics Adapter” to [Onboard] and “Share Memory” to [Auto], then the
onboard VGA will be enabled, and the primary screen will be onboard VGA.
Installing an expansion card
Step 1. Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Step 2. Remove the bracket facing the slot that you intend to use. Keep the screws
for later use.
Step 3. Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Step 4. Fasten the card to the chassis with screws.
2 1
Download from Www.Somanuals.com. All Manuals Search And Download.
2.7 Installation of ASR
o
c
k
D
V
I
_
D
i
s
p
l
a
y
P
o
r
t
C
a
r
d
This motherboard supports DVI-D and DisplayPort output options through the
bundled ASRock DVI_DisplayPort Card. As long as you install ASRock
DVI_DisplayPort Card on this motherboard, your motherboard will be able to
support DVI-D and DisplayPort devices. Please refer to the following steps to install
ASRock DVI_DisplayPort Card:
1. Install ASRock DVI_DisplayPort Card on PCIE2 slot (green). Please refer to page
21 for proper expansion card installation procedures for details.
PCIE2 slot
ASRock DVI_DisplayPort Card
ASRock DVI_DisplayPort Card
2. Connect the correspondent monitor cable to the DVI-D and DisplayPort of ASRock
DVI_DisplayPort Card on PCIE2 slot.
DisplayPort
DVI-D port
3. Boot your system.
2 2
Download from Www.Somanuals.com. All Manuals Search And Download.
HDCP Function
HDCP function is supported when you install ASRock DVI_DisplayPort
Card on this motherboard. To use HDCP function with this motherboard,
you need to adopt the monitor that supports HDCP function as well.
Therefore, you can enjoy the superior display quality with high-definition
HDCP encryption contents. Please refer to below instruction for more
details about HDCP function.
What is HDCP?
HDCP stands for High-Bandwidth Digital Content Protection, a
specification developed by Intel® for protecting digital entertainment
content that uses the DVI interface. HDCP is a copy protection
scheme to eliminate the possibility of intercepting digital data
midstream between the video source, or transmitter - such as a
computer, DVD player or set-top box - and the digital display, or
receiver - such as a monitor, television or projector. In other words,
HDCP specification is designed to protect the integrity of content as it
is being transmitted.
Products compatible with the HDCP scheme such as DVD players,
satellite and cable HDTV set-top-boxes, as well as few entertain-
ment PCs requires a secure connection to a compliant display. Due
to the increase in manufacturers employing HDCP in their equipment,
it is highly recommended that the HDTV or LCD monitor you purchase
is compatible.
2 3
Download from Www.Somanuals.com. All Manuals Search And Download.
2.8 Jumpers Setup
The illustration shows how jumpers are setup.
When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap is
placed on pins, the jumper is “Open”. The il-
lustration shows a 3-pin jumper whose pin1
and pin2 are “Short” when jumper cap is
placed on these 2 pins.
Jumper
Setting
Description
PS2_USB_PWR1
(see p.12 No. 1)
Short pin2, pin3 to enable
+5VSB (standby) for PS/2
or USB wake up events.
1_2
2_3
+5V
+5VSB
Note: To select +5VSB, it requires 2 Amp and higher standby current provided by
power supply.
Clear CMOS Jumper
1_2
2_3
(CLRCMOS1)
(see p.12, No. 3)
Default
Clear CMOS
Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes
system setup information such as system password, date, time, and system
setup parameters. To clear and reset the system parameters to default setup,
please turn off the computer and unplug the power cord from the power supply.
After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1
for 5 seconds. However, please do not clear the CMOS right after you update the
BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you
must boot up the system first, and then shut it down before you do the clear-
CMOS action.
FSB1 Jumper
(FSB1, 3-pin jumper, see p.12 No. 32)
1_2
FSB1
FSB2 Jumper
(FSB2, 5-pin jumper, see p.12 No. 31)
1_2
1_2
FSB3
FSB2
Default
FSB3 Jumper
(FSB3, 5-pin jumper, see p.12 No. 31)
When you mount a FSB800 or FSB1066 CPU, and try to overclock to FSB1333 (by
BIOS setting) you may face the problem, that DRAM frequency will be overclocked
very high. Please use jumper to force NB to be strapped at higher frequency, so
the DRAM can work at lower frequency.
2 4
Download from Www.Somanuals.com. All Manuals Search And Download.
If you want to overclock the CPU you adopt to FSB1066 on this motherboard, you
need to adjust the jumpers. Please short pin4, pin5 for FSB2 jumper and pin4, pin5 for
FSB3 jumper. Otherwise, the CPU may not work properly on this motherboard.
Please refer to below jumper settings.
1_2
FSB1
4_5
FSB3
FSB2
4_5
If you want to overclock the CPU you adopt to FSB1333 on this motherboard, you
need to adjust the jumpers. Please short pin3, pin4 for FSB2 jumper and pin4, pin5 for
FSB3 jumper. Otherwise, the CPU may not work properly on this motherboard.
Please refer to below jumper settings.
1_2
FSB1
4_5
FSB3
FSB2
3_4
If you use a FSB1333-CPU and adopt a DDR2 1066 memory module on this
motherboard, you need to adjust the jumpers. Please short pin4, pin5 for FSB2.
Otherwise, the CPU and memory module may not work properly on this motherboard.
Please refer to below jumper settings.
1_2
FSB1
1_2
FSB3
FSB1333 /DDR2 1066
FSB2
4_5
If you use a FSB1066-CPU and adopt a DDR2 1066 memory module on this
motherboard, you need to adjust the jumpers. Please short pin2, pin3 for FSB3.
Otherwise, the CPU and memory module may not work properly on this motherboard.
Please refer to below jumper settings.
1_2
FSB1
2_3
FSB3
FSB1066 /DDR2 1066
FSB2
1_2
2 5
Download from Www.Somanuals.com. All Manuals Search And Download.
2.9 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
FDD connector
(33-pin FLOPPY1)
(see p.12 No. 22)
FLOPPY1
Pin1
the red-striped side to Pin1
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
(39-pin IDE1, see p.12 No. 7)
IDE1
PIN1
connect the black end
to the IDE devices
connect the blue end
to the motherboard
80-conductorATA 66/100/133 cable
Note: Please refer to the instruction of your IDE device vendor for the details.
Serial ATAII Connectors
(SATAII_1:
These six Serial ATAII (SATAII)
connectors support SATA data
cables for internal storage
devices. The current SATAII
interface allows up to 3.0 Gb/s
data transfer rate.
see p.12, No. 12)
(SATAII_2:
see p.12,No. 11)
(SATAII_3:
see p.12, No. 13)
(SATAII_4:
SATAII_5
SATAII_6
SATAII_3
SATAII_4
see p.12, No. 14)
(SATAII_5:
see p.12, No. 16)
(SATAII_6:
see p.12, No. 15)
SerialATA (SATA)
Data Cable
Either end of the SATA data cable
can be connected to the SATA /
SATAII hard disk or the SATAII
connector on this motherboard.
(Optional)
2 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial ATA (SATA)
Power Cable
(Optional)
Please connect the black end of
SATA power cable to the power
connector on each drive. Then
connect the white end of SATA
power cable to the power
connect to the SATA HDD
powerconnector
connect to the
powersupply
connector of the power supply.
USB 2.0 Headers
(9-pin USB8_9)
Besides six default USB 2.0
ports on the I/O panel, there are
two USB 2.0 headers on this
motherboard. Each USB 2.0
header can support two USB
2.0 ports.
USB_PWR
P-9
P+9
GND
DUMMY
(see p.12 No. 17)
1
GND
P+8
P-8
USB_PWR
USB_PWR
P-7
(9-pin USB6_7)
(see p.12 No. 19)
P+7
GND
DUMMY
1
GND
P+6
P-6
USB_PWR
WiFi/E Header
(15-pin WIFI/E)
(see p.12 No. 23)
This header supports WiFi+AP
function with ASRock
USB+5V_2
TXN
TXP
GND2
PCIE_RST#
+3SVB
RXN
WiFi-802.11g or WiFi-802.11n
module, an easy-to-use wireless
local area network (WLAN)
adapter. It allows you to create a
wirelessenvironmentandenjoythe
convenience of wireless network
connectivity.
RXP
1
PexCLK
PexCLK#
PME#
GND1
D0+
D0-
USB+5V_1
If you don’t plan to use WiFi+AP functin on this motherboard, this header can be
used as a 4-Pin USB 2.0 header to support one USB 2.0 port. To connect the
4-Pin USB device cable to this header, please refer to
this picture for proper installation.
IRTX
+5V
DUMMY
Infrared Module Header
This header supports an
(5-pin IR1)
optional wireless transmitting
and receiving infrared module.
1
(see p.12 No. 27)
GND
IRRX
2 7
Download from Www.Somanuals.com. All Manuals Search And Download.
InternalAudio Connectors
(4-pin CD1)
This connector allows you
to receive stereo audio input
from sound sources such as
a CD-ROM, DVD-ROM, TV
tuner card, or MPEG card.
CD1
(CD1: see p.12 No. 26)
Front Panel Audio Header
(9-pin HD_AUDIO1)
This is an interface for front
panel audio cable that allows
convenient connection and
control of audio devices.
GND
PRESENCE#
MIC_RET
OUT_RET
(see p.12 No. 25)
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
1. High Definition Audio supports Jack Sensing, but the panel wire on
the chassis must support HDA to function correctly. Please follow the
instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio
header as below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t
need to connect them for AC’97 audio panel.
E. Enter BIOS Setup Utility. Enter Advanced Settings, and then select
Chipset Configuration. Set the Front Panel Control option from
[Auto] to [Enabled].
F. Enter Windows system. Click the icon on the lower right hand
taskbar to enter Realtek HD Audio Manager.
For Windows® 2000 / XP / XP 64-bit OS:
Click “Audio I/O”, select “Connector Settings”
, choose
“Disable front panel jack detection”, and save the change by
clicking “OK”.
For Windows® VistaTM / VistaTM 64-bit OS:
Click the right-top “Folder” icon
, choose “Disable front
panel jack detection”, and save the change by clicking “OK”.
G. To activate the front mic.
For Windows® 2000 / XP / XP 64-bit OS:
Please select “Front Mic” as default record device.
If you want to hear your voice through front mic, please deselect "Mute"
icon in “Front Mic” of “Playback” portion.
For Windows® VistaTM / VistaTM 64-bit OS:
Go to the "Front Mic" Tab in the Realtek Control panel.
Click "Set Default Device" to make the Front Mic as the default record
device.
2 8
Download from Www.Somanuals.com. All Manuals Search And Download.
PLED+
PLED-
PWRBTN#
GND
System Panel Header
(9-pin PANEL1)
This header accommodates
several system front panel
functions.
(see p.12 No. 10)
1
DUMMY
RESET#
GND
HDLED-
HDLED+
Chassis Speaker Header
Please connect the chassis
speaker to this header.
1
(4-pin SPEAKER 1)
(see p.12 No. 18)
SPEAKER
DUMMY
DUMMY
+5V
Chassis Fan Connector
(3-pin CHA_FAN1)
Please connect a chassis fan
cable to this connector and
match the black wire to the
ground pin.
GND
+12V
CHA_FAN_SPEED
(see p.12 No. 9)
CPU Fan Connector
(4-pin CPU_FAN1)
Please connect a CPU fan cable
to this connector and match
the black wire to the ground pin.
4
3
2
1
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
(see p.12 No. 33)
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin
CPU fan still can work successfully even without the fan speed control function.
If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this
motherboard, please connect it to Pin 1-3.
Pin 1-3 Connected
3-Pin Fan Installation
12
24
ATX Power Connector
Please connect anATX power
supply to this connector.
(24-pin ATXPWR1)
(see p.12, No. 6)
1
13
Though this motherboard provides 24-pin ATX power connector,
it can still work if you adopt a traditional 20-pin ATX power supply.
To use the 20-pin ATX power supply, please plug your
power supply along with Pin 1 and Pin 13.
12
24
20-Pin ATX Power Supply Installation
1
13
ATX 12V Power Connector
Please connect an ATX 12V
power supply to this connector.
(4-pin ATX12V1)
(see p.12 No. 1)
2 9
Download from Www.Somanuals.com. All Manuals Search And Download.
RRXD1
DDTR#1
DDSR#1
CCTS#1
Serial port Header
This COM1 header
(9-pin COM1)
supports a serial port module.
(see p.12 No.21)
1
RRI#1
RRTS#1
GND
TTXD1
DDCD#1
2.10 SA
T
A
I
I
H
a
r
d
D
i
s
k
S
e
t
u
p
G
u
i
d
e
Before installing SATAII hard disk to your computer, please carefully read below
SATAII hard disk setup guide. Some default setting of SATAII hard disks may not be
at SATAII mode, which operate with the best performance. In order to enable SATAII
function, please follow the below instruction with different vendors to correctly adjust
your SATAII hard disk to SATAII mode in advance; otherwise, your
SATAII hard disk may fail to run at SATAII mode.
Western Digital
7
5
6
3
1
8
4
2
If pin 5 and pin 6 are shorted, SATA 1.5Gb/s will be enabled.
On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the
jumpers from pin 5 and pin 6.
SAMSUNG
7
5
6
3
1
8
4
2
If pin 3 and pin 4 are shorted, SATA 1.5Gb/s will be enabled.
On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the
jumpers from pin 3 and pin 4.
HITACHI
Please use the Feature Tool, a DOS-bootable tool, for changing various ATA
features. Please visit HITACHI’s website for details:
The above examples are just for your reference. For different SATAII hard
disk products of different vendors, the jumper pin setting methods may
not be the same. Please visit the vendors’ website for the updates.
3 0
Download from Www.Somanuals.com. All Manuals Search And Download.
2.11
S
e
r
i
a
l
A
T
A
(
S
AT
A
)
/
S
e
r
i
a
l
A
T
A
I
I
(
S
A
T
A
I
I
)
H
a
r
d
D
i
s
k
s
Installation
This motherboard adopts Intel® ICH10 south bridge chipset that supports Serial ATA
(SATA) / Serial ATAII (SATAII) hard disks. You may install SATA / SATAII hard disks on
this motherboard for internal storage devices. This section will guide you to install the
SATA / SATAII hard disks.
STEP1: Install the SATA / SATAII hard disks into the drive bays of your chassis.
STEP2: Connect the SATA power cable to the SATA / SATAII hard disk.
STEP3: Connect one end of the SATA data cable to the motherboard’s SATAII
connector.
STEP4: Connect the other end of the SATA data cable to the SATA / SATAII hard
disk.
2.12 Hot Plug Function for SATA / SATAII HDDs
This motherboard supports Hot Plug function for SATA / SATAII in AHCI mode. Intel®
ICH10 south bridge chipset provides hardware support forAdvanced Host controller
Interface (AHCI), a new programming interface for SATA host controllers developed thru
a joint industry effort.
What is Hot Plug Function?
If the SATA / SATAII HDDs are NOT set for RAID configuration, it is called
“Hot Plug” for the action to insert and remove the SATA / SATAII HDDs
while the system is still power-on and in working condition.
However, please note that it cannot perform Hot Plug if the OS has been
installed into the SATA / SATAII HDD.
3 1
Download from Www.Somanuals.com. All Manuals Search And Download.
2.13 SA
T
A
/
S
A
T
A
I
I
H
D
D
H
o
t
P
l
u
g
F
e
a
t
u
r
e
a
n
d
O
p
e
r
a
t
i
o
n
Guide
This motherboard supports Hot Plug feature for SATA / SATAII HDD in AHCI mode.
Please read below operation guide of SATA / SATAII HDD Hot Plug feature carefully.
Before you process the SATA / SATAII HDD Hot Plug, please check below cable
accessories from the motherboard gift box pack.
A. 7-pin SATA data cable
B. SATA power cable with SATA 15-pin power connector interface
A. SATA data cable (Red)
B. SATA power cable
1x4-pin conventional
SATA7-pin
connector
The SATA 15-pin power
connector (Black) connect
to SATA / SATAII HDD
power connector (White)
connect to power supply
Caution
1. Without SATA 15-pin power connector interface, the SATA / SATAII Hot Plug
cannot be processed.
2. Even some SATA / SATAII HDDs provide both SATA 15-pin power connector
and IDE 1x4-pin conventional power connector interfaces, the IDE 1x4-pin
conventional power connector interface is definitely not able to support Hot
Plug and will cause the HDD damage and data loss.
Points of attention, before you process the Hot Plug:
1. Below operation procedure is designed only for our motherboard, which
supports SATA / SATAII HDD Hot Plug.
* The SATA / SATAII Hot Plug feature might not be supported by the chipset
because of its limitation, the SATA / SATAII Hot Plug support information of our
motherboard is indicated in the product spec on our website:
2. Make sure your SATA / SATAII HDD can support Hot Plug function from your
dealer or HDD user manual. The SATA / SATAII HDD, which cannot support Hot
Plug function, will be damaged under the Hot Plug operation.
3. Please make sure the SATA / SATAII driver is installed into system properly. The
latest SATA / SATAII driver is available on our support website:
4. Make sure to use the SATA power cable & data cable, which are from our
motherboard package.
5. Please follow below instructions step by step to reduce the risk of HDD crash
or data loss.
3 2
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Hot Plug a SATA / SATAII HDD:
Points of attention, before you process the Hot Plug:
Please do follow below instruction sequence to process the Hot Plug, improper
procedure will cause the SATA / SATAII HDD damage and data loss.
Step 1
Step 2
Please connect SATA power cable 1x4-pin end
(White) to the power supply 1x4-pin cable.
Connect SATA data cable to
the motherboard’s SATAII connector.
SATApowercable1x4-pin
power connector (White)
Step 4
Step 3
Connect SATA 15-pin power cable connector
(Black) end to SATA / SATAII HDD.
Connect SATA data cable to
the SATA / SATAII HDD.
How to Hot Unplug a SATA / SATAII HDD:
Points of attention, before you process the Hot Unplug:
Please do follow below instruction sequence to process the Hot Unplug, improper
procedure will cause the SATA / SATAII HDD damage and data loss.
Step 1
Unplug SATA data cable from SATA / SATAII HDD side.
Unplug SATA 15-pin power cable connector (Black) from SATA / SATAII HDD side.
Step 2
3 3
Download from Www.Somanuals.com. All Manuals Search And Download.
M
2.15
I
n
s
t
a
l
l
i
n
g
W
i
n
d
o
w
s®
2000 / XP / XP 64-bit / VistaT
/
2.14
D
r
i
v
e
r
I
n
s
t
a
l
l
a
t
i
o
n
G
u
i
d
e
To install the drivers to your system, please insert the support CD to your optical drive
first. Then, the drivers compatible to your system can be auto-detected and listed on
the support CD driver page. Please follow the order from up to bottom side to install
those required drivers. Therefore, the drivers you install can work properly.
VistaTM 64-bit Without RAID Functions
If you want to install Windows® 2000 / XP / XP 64-bit / VistaTM / VistaTM 64-bit OS
on your SATA / SATAII HDDs without RAID functions, please follow below
procedures according to the OS you install.
Since Windows® 2000 AHCI driver is not provided by the chipset vendor,
AHCI function is not supported under Windows® 2000.
2.15.1 Installing Windows® 2000 / XP / XP 64-bit
Without RAID Functions
If you want to install Windows® 2000 / XP / XP 64-bit OS on your SATA / SATAII HDDs
without RAID functions, please follow below steps.
Using SATA / SATAII HDDs with NCQ function
STEP 1: Set Up BIOS.
A. Enter BIOS SETUP UTILITY Advanced screen
IDE Configuration.
B. Set “SATAII Configuration” to [Enhanced], and then in the option “Configure
SATAII as”, please set the option to [AHCI].
STEP 2: Make a SATA / SATAII Driver Diskette.
A. Insert the Support CD into your optical drive to boot your system.
B. During POST at the beginning of system boot-up, press <F11> key, and then a
window for boot devices selection appears. Please select CD-ROM as the boot
device.
C. When you see the message on the screen, “Do you want to generate Serial
ATA driver diskette [YN]?”, press <Y>.
D. Then you will see these messages,
Please insert a diskette into the floppy drive.
WARNING! Formatting the floppy diskette will
lose ALL data in it!
Start to format and copy files [YN]?
Please insert a floppy diskette into the floppy drive, and press <Y>.
E. The system will start to format the floppy diskette and copy SATA / SATAII
drivers into the floppy diskette.
3 4
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3: Install Windows® XP / XP 64-bit OS on your system. (Windows® 2000 is
not supported.)
After making a SATA / SATAII driver diskette, you can start to install Windows® XP / XP
64-bit on your system. At the beginning of Windows® setup, press F6 to install a third-
party AHCI driver. When prompted, insert the SATA / SATAII driver diskette containing
the Intel® AHCI driver. After reading the floppy disk, the driver will be presented. Select
the driver to install according to the mode you choose and the OS you install. You may
select: "Intel(R) ICH10 SATAAHCI Controller (Desktop - Windows XP)" for Windows® XP
or "Intel(R) ICH10 SATAAHCI Controller (Desktop - Windows XP64)" for Windows® XP
64-bit.
Using SATA / SATAII HDDs without NCQ function
STEP 1: Set up BIOS.
A. Enter BIOS SETUP UTILITY Advanced screen
IDE Configuration.
B. Set “SATAII Configuration” to [Enhanced], and then in the option “Configure
SATAII as”, please set the option to [IDE].
STEP 2: Install Windows® 2000 / XP / XP 64-bit OS on your system.
2.15.2 Installing Windows® VistaTM / VistaTM 64-bit
Without RAID Functions
If you want to install Windows® VistaTM / VistaTM 64-bit OS on your SATA / SATAII
HDDs without RAID functions, please follow below steps.
Using SATA / SATAII HDDs with NCQ function
STEP 1: Set Up BIOS.
A. Enter BIOS SETUP UTILITY Advanced screen
IDE Configuration.
B. Set “SATAII Configuration” to [Enhanced], and then in the option “Configure
SATAII as”, please set the option to [AHCI].
STEP 2: Install Windows® VistaTM / VistaTM 64-bit OS on your system.
Insert the Windows® VistaTM / VistaTM 64-bit optical disk into the optical drive to boot
your system, and follow the instruction to install Windows® VistaTM / VistaTM 64-bit OS
on your system. When you see “Where do you want to install Windows?” page, please
insert the ASRock Support CD into your optical drive, and click the “Load Driver” button
on the left on the bottom to load the Intel® AHCI drivers. Intel® AHCI drivers are in the
following path in our Support CD:
.. \ I386 (For Windows® VistaTM OS)
.. \ AMD64 (For Windows® VistaTM 64-bit OS)
After that, please insert Windows® VistaTM / VistaTM 64-bit optical disk into the optical
drive again to continue the installation.
3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Using SATA / SATAII HDDs without NCQ function
STEP 1: Set up BIOS.
A. Enter BIOS SETUP UTILITY Advanced screen
IDE Configuration.
B. Set “SATAII Configuration” to [Enhanced], and then in the option “Configure
SATAII as”, please set the option to [IDE].
STEP 2: Install Windows® VistaTM / VistaTM 64-bit OS on your system.
2.16
U
n
t
i
e
d
O
v
e
r
c
l
o
c
k
i
n
g
T
e
c
h
n
o
l
o
g
y
This motherboard supports Untied Overclocking Technology, which means during
overclocking, FSB enjoys better margin due to fixed PCI / PCIE buses. Before you
enable Untied Overclocking function, please enter “Overclock Mode” option of BIOS
setup to set the selection from [Auto] to [Manual]. Therefore, CPU FSB is untied
during overclocking, but PCI / PCIE buses are in the fixed mode so that FSB can
operate under a more stable overclocking environment.
Please refer to the warning on page 8 for the possible overclocking risk
before you apply Untied Overclocking Technology.
3 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: BIOS SETUP UTILITY
3.1 Introduction
This section explains how to use the BIOS SETUP UTILITY to configure your system.
The BIOS FWH chip on the motherboard stores the BIOS SETUP UTILITY. You may
run the BIOS SETUP UTILITY when you start up the computer. Please press <F2>
during the Power-On-Self-Test (POST) to enter the BIOS SETUP UTILITY, otherwise,
POST will continue with its test routines.
If you wish to enter the BIOS SETUP UTILITY after POST, restart the system by
pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system
chassis. You may also restart by turning the system off and then back on.
Because the BIOS software is constantly being updated, the
following BIOS setup screens and descriptions are for refer-
ence purpose only, and they may not exactly match what you
see on your screen.
3.1.1 BIOS Menu Bar
The top of the screen has a menu bar with the following selections:
Main
To set up the system time/date information
To set up the advanced BIOS features
Advanced
H/W Monitor To display current hardware status
Boot
To set up the default system device to locate and load the
Operating System
Security
Exit
To set up the security features
To exit the current screen or the BIOS SETUP UTILITY
Use < > key or < > key to choose among the selections on the menu bar,
and then press <Enter> to get into the sub screen.
3 7
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1.2
N
a
v
i
g
a
t
i
o
n
K
e
y
s
Please check the following table for the function description of each navigation key.
Navigation Key(s)
Function Description
/
/
Moves cursor left or right to select Screens
Moves cursor up or down to select items
To change option for the selected items
To bring up the selected screen
+ / -
<Enter>
<F1>
<F9>
<F10>
<ESC>
To display the General Help Screen
To load optimal default values for all the settings
To save changes and exit the BIOS SETUP UTILITY
To jump to the Exit Screen or exit the current screen
3.2 Main Screen
When you enter the BIOS SETUP UTILITY, the Main screen will appear and display the
system overview.
BIOS SETUP UTILITY
Smart Advanced H/W Monitor Boot Security Exit
Main
System Overview
Use [Enter], [TAB]
or [SHIFT-TAB] to
System Time
System Date
[14:00:09]
[Thu 07/10/2008]
select
a
field.
BIOS Version
Processor Type
:
:
G43Twins-FullHD P1.00
Intel(R) CPU
2.13GHz (64bit)
Use [+] or [-] to
configure system Time.
@
Processor Speed
Microcode Update
Cache Size
:
:
:
2133MHz
6F4/0
2048KB
Select Screen
Select Item
Total Memory
:
1024MB with 128MB shared memory
and 2MB GTT memory
Single-Channel Memory Mode
1024MB/333MHz (DDR2 667)
None
None
None
+-
Tab
F1
F9
F10
ESC
Change Field
Select Field
General Help
Load Defaults
Save and Exit
Exit
DDRII_1
DDRII_2
DDR3_A1
DDR3_B1
:
:
:
:
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
System Time [Hour:Minute:Second]
Use this item to specify the system time.
System Date [Day Month/Date/Year]
Use this item to specify the system date.
3 8
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3
S
m
a
r
t
S
c
r
e
e
n
In the Smart screen, you can load the BIOS setup according to your requirements.
BIOS SETUP UTILITY
Main
Advanced H/W Monitor
Boot
Security
Exit
Smart
Exit system setup
after saving the
changes.
Smart Settings
Save Changes and Exit
F10 key can be used
for this operation.
Load BIOS Defaults
Load Performance Setup Default (IDE/SATA)
Load Performance Setup AHCI Mode
Load Power Saving Setup Default
Select Screen
Select Item
Enter Go to Sub Screen
F1
F9
F10
ESC
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
Save Changes and Exit
When you select this option, it will pop-out the following message, “Save
configuration changes and exit setup?” Select [OK] to save the changes
and exit the BIOS SETUP UTILITY.
Load BIOS Defaults
Load BIOS default values for all the setup questions. F9 key can be used
for this operation.
Load Performance Setup Default (IDE/SATA)
This performance setup default may not be compatible with all system
configurations. If system boot failure occurs after loading, please resume
optimal default settings. F5 key can be used for this operation.
Load Performance Setup AHCI Mode
This performance setup AHCI mode may not be compatible with all system
configurations. If system boot failure occurs after loading, please resume
optimal default settings. F3 key can be used for this operation.
Load Power Saving Setup Default
Load power saving setup default. F6 key can be used for this operation.
3 9
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4.1
C
P
U
C
o
n
f
i
g
BIOS SETUP UTILITY
u
r
a
t
i
o
n
3.4
A
d
v
a
n
c
e
d
S
c
r
e
e
n
In this section, you may set the configurations for the following items: CPU Configuration,
Chipset Configuration, ACPI Configuration, IDE Configuration, PCIPnP Configuration,
Floppy Configuration, SuperIO Configuration, and USB Configuration.
BIOS SETUP UTILITY
Advanced H/W Monitor
Boot
Security
Exit
Main Smart
Options for CPU
Advanced Settings
WARNING : Setting wrong values in below sections
may cause system to malfunction.
CPU Configuration
Chipset Configuration
ACPI Configuration
IDE Configuration
PCIPnP Configuration
Floppy Configuration
SuperIO Configuration
USB Configuration
Select Screen
Select Item
Enter Go to Sub Screen
F1
F9
General Help
Load Defaults
Save and Exit
F10
ESC Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
Setting wrong values in this section may cause
the system to malfunction.
Advanced
Select the over clock
mode.
CPU Configuration
Overclock Mode
[Auto]
[266]
[100]
CPU Frequency (MHz)
PCIE Frequency (MHz)
[Enabled]
[Auto]
Boot Failure Guard
Spread Spectrum
Ratio Status
Ratio Actual Value
Unlocked (Min: 06, Max: 08)
8
[Disabled]
[Enabled]
[Enabled]
[Disabled]
[Enabled]
[Auto]
Select Screen
Select Item
Enhanced Halt State
Intel Virtualization tech.
CPU Thermal Throttling
No-Excute Memory Protection
Hyper Threading Technology
Intel (R) SpeedStep(tm) tech.
+-
F1
F9
F10
ESC
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
Overclock Mode
Use this to select Overclock Mode. Configuration options: [Auto], [Manual],
[I.O.T.] and [Optimized]. The default value is [Auto]. If you select [Manual],
Untied Overclocking function is enabled. Please refer to page 36 for the
details of Untied Overclocking Technology. If you select [I.O.T.] (Intelligent
Overclocking Technology), you are allowed to adjust the CPU frequency
and PCIE frequency in the following two items. Therefore, the system will
automatically enable the overclocking function when your CPU is heavy
loaded.
4 0
Download from Www.Somanuals.com. All Manuals Search And Download.
CPU Frequency (MHz)
Use this option to adjust CPU frequency.
PCIE Frequency (MHz)
Use this option to adjust PCIE frequency.
Boot Failure Guard
Enable or disable the feature of Boot Failure Guard.
Spread Spectrum
This item should always be [Auto] for better system stability.
Ratio Status
This is a read-only item, which displays whether the ratio status of this
motherboard is “Locked” or “Unlocked”. If it shows “Unlocked”, you will find
an item Ratio CMOS Setting appears to allow you changing the ratio
value of this motherboard.
Ratio Actual Value
This is a read-only item, which displays the ratio actual value of this
motherboard.
Enhance Halt State
All processors support the Halt State (C1). The C1 state is supported
through the native processor instructions HLT and MWAIT and requires no
hardware support from the chipset. In the C1 power state, the processor
maintains the context of the system caches.
Intel (R) Virtualization tech.
When this option is set to [Enabled], a VMM (Virtual Machine Architecture)
can utilize the additional hardware capabilities provided by Vanderpool
Technology. This option will be hidden if the installed CPU does not support
Intel (R) Virtualization Technology.
CPU Thermal Throttling
You may select [Enabled] to enable P4 CPU internal thermal control mecha-
nism to keep the CPU from overheated.
No-Excute Memory Protection
No-Execution (NX) Memory Protection Technology is an enhancement to
the IA-32 Intel Architecture. An IA-32 processor with “No Execute (NX)
Memory Protection” can prevent data pages from being used by malicious
software to execute code. This option will be hidden if the current CPU
does not support No-Excute Memory Protection.
Hyper Threading Technology
To enable this feature, it requires a computer system with an Intel Pentium®
4 processor that supports Hyper-Threading technology and an operating
system that includes optimization for this technology, such as Microsoft®
Windows® XP. Set to [Enabled] if using Microsoft® Windows® XP, or Linux
kernel version 2.4.18 or higher. This option will be hidden if the installed
CPU does not support Hyper-Threading technology.
4 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Intel (R) SpeedStep(tm) tech.
Intel (R) SpeedStep(tm) tech. is Intel’s new power saving technology.
Processor can switch between multiple frequency and voltage points to
enable powersavings. The default value is [Auto]. Configuration options:
[Auto], [Enabled] and [Disabled]. If you install Windows® XP and select
[Auto], you need to set the “Power Schemes” as “Portable/Laptop” to en-
able this function. If you install Windows® VistaTM and want to enable this
function, please set this item to [Enabled]. This item will be hidden if the
current CPU does not support Intel (R) SpeedStep(tm) tech..
Please note that enabling this function may reduce CPU voltage and lead to system
stability or compatibility issue with some power supplies. Please set this item to
[Disable] if above issue occurs.
3.4.2
C
h
i
p
s
e
t
C
o
n
f
i
g
u
r
a
t
i
o
n
BIOS SETUP UTILITY
Advanced
Chipset Configuration
ENABLE: Allow
remapping of
overlapped PCI memory
above the total
physical memory.
[Disabled]
[Auto]
[Disabled]
Memory Remap Feature
DRAM Frequency
Flexibility Option
Standard Memory Info
DRAM tCL
DRAM tRAS
:
4-15-5-5-5-26-3-3-3
[Auto]
[Auto]
DISABLE: Do not allow
remapping of memory.
[Auto]
[Auto]
DRAM tRP
DRAM tRCD
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
DRAM tWR
DRAM tRFC
DRAM tWTR
DRAM tRRD
DRAM tRTP
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
+ -
F1
F9
F10
Advanced Memory Info
:
18-18-9-9-0-0
[Auto]
[Auto]
DRAM CH0 RCOMP ODT
DRAM CH1 RCOMP ODT
DRAM CH0 tRD
ESC Exit
[Auto]
[Auto]
DRAM CH1 tRD
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
Memory Remap Feature
Use this item to enable or disable memory remap feature. Configuration options:
[Enabled] and [Disabled]. The default value is [Disabled].
DRAM Frequency
If [Auto] is selected, the motherboard will detect the memory module(s) in-
serted and assigns appropriate frequency automatically. You may select
[333MHz (DDR2 667)], [400MHz (DDR2 800)] or [533MHz (DDR2 1066)] for
DDR2 memory modules, or select [400MHz (DDR3 800)] or [533MHz (DDR3
1066)] for DDR3 memory modules. The configuration options depend on the
CPU and memory module you adopt on this motherboard. Please refer to page
8 for the CPU FSB frequency and its corresponding memory support frequency.
Flexibility Option
The default value of this option is [Disabled]. It will allow better tolerance for
memory compatibility when it is set to [Enabled].
Standard Memory Info : 4-15-5-5-5-26-3-3-3
4 2
Download from Www.Somanuals.com. All Manuals Search And Download.
DRAM tCL
Use this item to adjust the means of memory accessing. Configuration
options for DDR2 memory modules are [3], [4], [5], [6], [7] and [Auto].
Configuration options for DDR3 memory modules are are [5], [6], [7], [8], [9],
[10] and [Auto].
DRAM tRAS
This controls the number of DRAM clocks for TRAS. Configuration options:
Configuration options: [Auto], [9] to [24].
DRAM tRP
This controls the number of DRAM clocks for TRP. Configuration options:
Configuration options: [Auto], [3] to [10].
DRAM tRCD
This controls the number of DRAM clocks for TRCD. Configuration options:
Configuration options: [Auto], [3] to [10].
DRAM tWR
This controls the number of DRAM clocks for TWR. Configuration options:
Configuration options: [Auto], [3] to [15].
DRAM tRFC
This controls the number of DRAM clocks for TRFC. Configuration options:
Configuration options: [Auto], [15] to [78].
DRAM tWTR
This controls the number of DRAM clocks for TWTR. Configuration options:
Configuration options: [Auto], [2] to [15].
DRAM tRRD
This controls the number of DRAM clocks for TRRD. Configuration options:
Configuration options: [Auto], [2] to [15].
DRAM tRTP
This controls the number of DRAM clocks for TRTP. Configuration options:
Configuration options: [Auto], [2] to [15].
Advanced Memory Info : 18-18-9-9-0-0
DRAM CH0 RCOMP ODT
This controls the number of DRAM clocks for CH0 RCOMP ODT.
Configuration options: Configuration options: [Auto], [1] to [63].
DRAM CH1 RCOMP ODT
This controls the number of DRAM clocks for CH1 RCOMP ODT.
Configuration options: Configuration options: [Auto], [1] to [63].
DRAM CH0 tRD
This controls the number ofDRAM clocks for CH0 TRD. Configuration options:
Configuration options: [Auto], [0] to [30].
DRAM CH1 tRD
This controls the number ofDRAM clocks for CH1 TRD. Configuration options:
Configuration options: [Auto], [0] to [30].
4 3
Download from Www.Somanuals.com. All Manuals Search And Download.
DRAM CH0 tRD Phase Adjust
This controls the number of DRAM clocks for CH0 TRD Phase Adjust.
Configuration options: Configuration options: [Auto], [0] to [62].
DRAM CH1 tRD Phase Adjust
This controls the number of DRAM clocks for CH1 TRD Phase Adjust.
Configuration options: Configuration options: [Auto], [0] to [62].
Primary Graphics Adapter
This allows you to select [Onboard], [PCI] or [PCI Express] as the boot
graphic adapter priority. The default value is [PCI].
Share Memory
This allows you to set share memory feature. The default value is [Auto].
Configuration options: [Auto], [48MB], [64MB], [128MB] and [256MB].
PAVP Mode
Use this option to adjust PAVP mode. Configuration options: [Disabled],
[Lite] and [Paranoid]. The default value is [Disabled]. PAVP is the new graphics
feature in Intel® 4 Series Express chipset family to support increased con-
tent protection and robustness requirements for premium content playback
(Blu-ray disc). There are two modes for PAVP. [Lite] mode is the encryption
of compressed video buffer and is hardware-based 128-bit AES decryption.
[Paranoid] mode includes protected memory for storing unencrypted video
content. If you want to use Blu-ray (BD) / HD-DVD playback function, please
set this option to [Disabled].
DVMT Mode Select
Use this option to adjust DVMT mode. The default value is [DVMT Mode].
DVMT (Dynamic Video Memory Technology) is an architecture that offers
breakthrough performance for the motherboard through efficient memory
utilization. In DVMT mode, the graphics driver allocates memory as needed
for running graphics applications and is cooperatively using this memory
with other system components. This item will not be used under Windows®
VistaTM OS because the driver will intelligently detect physical memory
available and allocate necessary video memory.
DVMT/FIXED Memory
You are allowed to adjust the shared memory size in this item if you set
DVMT Mode Select as [DVMT Mode]. Configuration options: [128MB], [256MB]
and [Maximum DVMT]. The option [Maximum DVMT] only appears when you
adopt the memory module with 1024MB or above.
Boot Display Device
This item allows you to select the boot display device. Configuration options:
[VGA1 + DVI], [VGA1] and [VGA1 + DisplayPort]. The default value is
[VGA1 + DVI].
4 4
Download from Www.Somanuals.com. All Manuals Search And Download.
OnBoard HD Audio
Select [Auto], [Enabled] or [Disabled] for the onboard HD Audio feature. If
you select [Auto], the onboard HD Audio will be disabled when PCI Sound
Card is plugged.
Front Panel
Select [Auto], [Enabled] or [Disabled] for the onboard HDAudio Front Panel.
CD-In
Use this item to enable or disable CD-In of OnBoard HDAudio. If you plan
to use this motherboard to submit Windows® VistaTM logo test, please
disable this option.
OnBoard Lan
This allows you to enable or disable the “OnBoard Lan” feature.
CPU Voltage
Use this to select CPU Voltage. Configuration options: [Auto] and [Manual].
The default value of this feature is [Auto].
DRAM Voltage
Use this to select DRAM Voltage. Configuration options for DDR2 memory
modules: [Auto], [1.80V], [1.86V], [1.92V], [1.98V], [2.04V], [2.10V],
[2.15V], [2.21V], [2.32], [2.38V], [2.44V], [2.50V], [2.56V], [2.62V], [2.67V]
and [2.73V]. Configuration options for DDR3 memory modules: [Auto],
[1.54V], [1.60V], [1.66V], [1.71V], [1.78V], [1.83V], [1.89V], [1.95V],
[2.06V], [2.12V], [2.18V], [2.23V], [2.29V], [2.35V], [2.41V] and [2.47V].
The default value of this feature is [Auto].
NB Core Voltage
Use this to select NB Core Voltage. Configuration options: [Auto], [Low],
[Middle], [High] and [Highest]. The default value of this feature is [Auto].
SB Core Voltage
Use this to select SB Core Voltage. Configuration options: [Auto], [Low],
[Middle], [High] and [Highest]. The default value of this feature is [Auto].
VTT Voltage
Use this to select VTT Voltage. Configuration options: [Auto], [Low],
[Middle], [High] and [Highest]. The default value of this feature is [Auto].
GLTREF Voltage
Use this to select GLTREF Voltage. Configuration options: [Auto],
[0.67 x Vtt], [0.65 x Vtt], [0.63 x Vtt] and [0.615 x Vtt]. The default value of
this feature is [Auto].
CIR10 Field 1
Use this to enable or disable CIR10 Field 1. The default value of this feature
is [Enabled].
4 5
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4.3
A
C
P
I
C
o
n
f
i
g
u
r
a
t
i
o
n
BIOS SETUP UTILITY
Advanced
ACPI Configuration
Suspend To RAM
Select auto-detect or
disable the STR
feature.
[Auto]
[No]
[Enabled]
Repost Video on STR Resume
Check Ready Bit
[Power Off]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
Restore on AC/Power Loss
Ring-In Power On
PCI Devices Power On
PS / 2 Keyboard Power On
RTC Alarm Power On
Select Screen
Select Item
[Disabled]
ACPI HPET Table
+-
F1
F9
F10
ESC
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
Suspend to RAM
Use this item to select whether to auto-detect or disable the Suspend-to-
RAM feature. Select [Auto] will enable this feature if the OS supports it. If
you set this item to [Disabled], the function “Repost Video on STR Resume”
will be hidden.
Repost Video on STR Resume
This feature allows you to repost video on STR resume. (STR refers to
suspend to RAM.)
Check Ready Bit
Use this item to enable or disable the feature Check Ready Bit.
Restore on AC/Power Loss
This allows you to set the power state after an unexpected AC/power
loss. If [Power Off] is selected, the AC/power remains off when the
power recovers. If [Power On] is selected, the AC/power resumes
and the system starts to boot up when the power recovers.
Ring-In Power On
Use this item to enable or disable Ring-In signals to turn on the system from
the power-soft-off mode.
PCI Devices Power On
Use this item to enable or disable PCI devices to turn on the system from the
power-soft-off mode.
PS/2 Keyboard Power On
Use this item to enable or disable PS/2 keyboard to turn on the system from
the power-soft-off mode.
RTC Alarm Power On
Use this item to enable or disable RTC (Real Time Clock) to power on the
system.
4 6
Download from Www.Somanuals.com. All Manuals Search And Download.
ACPI HPET Table
Use this item to enable or disable ACPI HPET Table. The default value is
[Disabled]. Please set this option to [Enabled] if you plan to use this
motherboard to submit Windows® VistaTM certification.
3.4.4
I
D
E
C
o
n
f
i
g
u
r
a
t
i
o
n
BIOS SETUP UTILITY
Advanced
Options
Disabled
Compatible
Enhanced
IDE Configuration
[Enhanced]
[IDE]
SATAII Configuration
Configure SATAII as
OnBoard IDE Controller
[Enabled]
SATAII
SATAII
SATAII
SATAII
SATAII
SATAII
1
2
3
4
5
6
[Hard Disk]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
IDE1 Master
IDE1 Slave
+-
F1
F9
F10
ESC
AHCI CD/DVD Boot Time out
[20]
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
SATAII Configuration
Please select [Compatible] when you install legacy OS. If native OS (Windows
2000 / XP) is installed, please select [Enhanced]. Then in the option
“Configure SATAII as”, you are allowed to set the selection to [AHCI] or [IDE]
mode. The default value is [IDE].
If you select [AHCI] mode, the option “Hot Plug” will appear. You are allowed to
use the Hot Plug function under Windows environment if this option is enabled.
Configuration options: [Enabled] and [Disabled].
AHCI(AdvancedHostControllerInterface)supportsNCQandother
new features that will improve SATA disk performance but IDE
mode does not have these advantages.
4 7
Download from Www.Somanuals.com. All Manuals Search And Download.
IDE Device Configuration
You may set the IDE configuration for the device that you specify. We will
use the “Primary IDE Master” as the example in the following instruction.
BIOS SETUP UTILITY
Advanced
Primary IDE Master
Select the type
of device connected
to the system.
Device
Vendor
Size
:Hard Disk
:ST340014A
:40.0 GB
LBA Mode
Block Mode
PIO Mode
Async DMA
Ultra DMA
S.M.A.R.T.
:Supported
:16Sectors
:4
:MultiWord DMA-2
:Ultra DMA-5
:Supported
Type
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Disabled]
[Enabled]
Select Screen
Select Item
LBA/Large Mode
Block (Multi-Sector Transfer)
PIO Mode
DMA Mode
S . M . A . R . T .
32Bit Data Transfer
+-
F1
F9
F10
ESC
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
TYPE
Use this item to configure the type of the IDE device that you specify.
Configuration options: [Not Installed], [Auto], [CD/DVD], and [ARMD].
[Not Installed]: Select [Not Installed] to disable the use of IDE device.
[Auto]: Select [Auto] to automatically detect the hard disk drive.
After selecting the hard disk information into BIOS, use a disk
utility, such as FDISK, to partition and format the new IDE hard
disk drives. This is necessary so that you can write or read
data from the hard disk. Make sure to set the partition of the
Primary IDE hard disk drives to active.
[CD/DVD]: This is used for IDE CD/DVD drives.
[ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device),
such as MO.
LBA/Large Mode
Use this item to select the LBA/Large mode for a hard disk > 512 MB under
DOS and Windows; for Netware and UNIX user, select [Disabled] to
disable the LBA/Large mode.
Block (Multi-Sector Transfer)
The default value of this item is [Auto]. If this feature is enabled, it will
enhance hard disk performance by reading or writing more data during
each transfer.
PIO Mode
Use this item to set the PIO mode to enhance hard disk performance by
optimizing the hard disk timing.
4 8
Download from Www.Somanuals.com. All Manuals Search And Download.
DMA Mode
DMA capability allows the improved transfer-speed and data-integrity for com-
patible IDE devices.
S.M.A.R.T.
Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis,
and Reporting Technology) feature. Configuration options: [Disabled], [Auto],
[Enabled].
32-Bit Data Transfer
Use this item to enable 32-bit access to maximize the IDE hard disk data
transfer rate.
3.4.5
P
C
I
P
n
P
C
o
n
f
i
g
u
r
a
t
i
o
n
BIOS SETUP UTILITY
Advanced
Value in units of PCI
clocks for PCI device
latency timer
Advanced PCI / PnP Settings
PCI Latency Timer
PCI IDE BusMaster
[32]
[Enabled]
register.
Select Screen
Select Item
+-
Change Option
General Help
Load Defaults
Save and Exit
F1
F9
F10
ESC Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
PCI Latency Timer
The default value is 32. It is recommended to keep the default value unless
the installed PCI expansion cards’ specifications require other settings.
PCI IDE BusMaster
Use this item to enable or disable the PCI IDE BusMaster feature.
4 9
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4.6
F
l
o
p
p
y
C
o
n
f
i
g
u
r
a
t
i
o
n
In this section, you may configure the type of your floppy drive.
BIOS SETUP UTILITY
Advanced
Floppy Configuration
Floppy
Select the type of
floppy drive
connected to the
system.
[1.44 MB 31 "]
A
2
Select Screen
Select Item
+-
F1
F9
F10
ESC
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
3.4.7 Super IO Configuration
BIOS SETUP UTILITY
Advanced
Configure Super IO Chipset
Allow BIOS to Enable
or Disable Floppy
Controller.
[Enabled]
[3F8 / IRQ4]
[Disabled]
OnBoard Floppy Controller
Serial Port Address
Infrared Port Address
Select Screen
Select Item
+-
Change Option
General Help
Load Defaults
Save and Exit
F1
F9
F10
ESC Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
OnBoard Floppy Controller
Use this item to enable or disable floppy drive controller.
Serial Port Address
Use this item to set the address for the onboard serial port or disable it.
Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4],
[2E8 / IRQ3].
Infrared Port Address
Use this item to set the address for the onboard infrared port or disable it.
Configuration options: [Disabled], [2F8 / IRQ3], and [2E8 / IRQ3].
5 0
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4.8
U
S
B
C
o
n
f
i
g
u
r
a
t
i
o
n
BIOS SETUP UTILITY
Advanced
USB Configuration
To enable or disable
the onboard USB
controllers.
[Enabled]
USB Controller
USB 2.0 Support
Legacy USB Support
[Enabled]
[BIOS Setup Only]
Select Screen
Select Item
+-
F1
F9
F10
ESC
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
USB Controller
Use this item to enable or disable the use of USB controller.
USB 2.0 Support
Use this item to enable or disable the USB 2.0 support.
Legacy USB Support
Use this option to select legacy support for USB devices. There are four
configuration options: [Enabled], [Auto], [Disabled] and [BIOS Setup Only].
The default value is [BIOS Setup Only]. Please refer to below descriptions
for the details of these four options:
[Enabled] - Enables support for legacy USB.
[Auto] - Enables legacy support if USB devices are connected.
[Disabled] - USB devices are not allowed to use under legacy OS and BIOS
setup when [Disabled] is selected. If you have USB compatibility issue, it is
recommended to select [Disabled] to enter OS.
[BIOS Setup Only] - USB devices are allowed to use only under BIOS setup
and Windows / Linux OS.
5 1
Download from Www.Somanuals.com. All Manuals Search And Download.
3.5
H
a
r
d
w
a
r
e
H
e
a
l
t
h
E
v
e
n
t
M
o
n
i
t
o
r
i
n
g
S
c
r
e
e
n
In this section, it allows you to monitor the status of the hardware on your system,
including the parameters of the CPU temperature, motherboard temperature, CPU fan
speed, chassis fan speed, and the critical voltage.
BIOS SETUP UTILITY
Boot
Security
Exit
Main Smart Advanced H/W Monitor
Enable/Disable
CPU Quiet Fan
Function.
Hardware Health Event Monitoring
CPU Temperature
M / B Temperature
:
:
37 C / 98 F
31 C / 87 F
CPU Fan Speed
Chassis Fan Speed
:
:
3400 RPM
N / A
Vcore
:
:
:
:
1.629V
3.306V
5.067V
11.890V
+
+
+
3.30V
5.00V
12.00V
Select Screen
Select Item
General Help
Load Defaults
Save and Exit
Exit
F1
F9
F10
ESC
CPU Quiet Fan
[Disabled]
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
CPU Quiet Fan
This item allows you to identify the temperature of CPU fan. If you set this
option as [Disabled], the CPU fan will operate in full speed. If you set this
option as [Enabled], you will find the items “Target CPU Temperature” and
“Target Fan Speed” appear to allow you adjusting them. The default value is
[Disabled]. You are allowed to enable this function only when you install 4-pin
CPU fan.
Target CPU Temperature
The target temperature will be between 45 C/113 F and 65 C/149 F. The
default value is [50 C/122 F].
Target Fan Speed
Use this option to set the target fan speed. You can freely adjust the
target fan speed according to the target CPU temperature that you
choose. Configuration options: [Level 1], [Level 2], [Level 3], [Level 4],
[Level 5], [Level 6] [Level 7], [Level 8] and [Level 9].
5 2
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6.1
B
o
o
t
S
e
t
t
i
n
g
s
C
o
n
f
i
g
u
r
a
t
i
o
n
3.6
B
o
o
t
S
c
r
e
e
n
In this section, it will display the available devices on your system for you to config-
ure the boot settings and the boot priority.
BIOS SETUP UTILITY
Main Smart Advanced H/W Monitor
Boot
Security Exit
Boot Settings
Configure Settings
during System Boot.
Boot Settings Configuration
[1st Floppy Device]
1st Boot Device
2nd Boot Device
3rd Boot Device
4th Boot Device
Hard Disk Drives
Removable Drives
CD/DVD Drives
[HDD: PM - HDS722580VL]
[CD / DVD: 3S - CD - ROM C]
[USB]
Select Screen
Select Item
Enter Go to Sub Screen
F1
F9
F10
ESC
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
BIOS SETUP UTILITY
Boot
Boot Settings Configuration
Disabled: Displays
normal POST messages.
Enabled: Displays OEM
Logo instead of POST
messages.
Full Screen Logo
AddOn ROM Display
Boot Logo
[Enabled]
[Enabled]
[Auto]
Boot From Onboard LAN
Bootup Num-Lock
[Disabled]
[On]
Select Screen
Select Item
+ -
F1
F9
F10
ESC
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Full Screen Logo
Use this item to enable or disable OEM Logo. The default value is [Enabled].
AddOn ROM Display
Use this option to adjust AddOn ROM Display. If you enable the option
“Full Screen Logo” but you want to see the AddOn ROM information when the
system boots, please select [Enabled]. Configuration options: [Enabled] and
[Disabled]. The default value is [Enabled].
5 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Boot Logo
Use this option to select logo in POST screen. This option only appears when
you enable the option “Full Screen Logo”. Configuration options: [Auto],
[PCIE2.0 Revolution], [Scenery] and [ASRock]. The default value is [Auto].
Currently, the option [Auto] is set to Aircraft.
Boot From Onboard LAN
Use this item to enable or disable the Boot From Onboard LAN feature.
Boot Up Num-Lock
If this item is set to [On], it will automatically activate the Numeric Lock
function after boot-up.
3.7
S
e
c
u
r
i
t
y
S
c
r
e
e
n
In this section, you may set or change the supervisor/user password for the system. For
the user password, you may also clear it.
BIOS SETUP UTILITY
Main Smart Advanced H/W Monitor Boot
Security
Exit
Security Settings
Install or Change the
password.
Supervisor Password : Not Installed
User Password
: Not Installed
Change Supervisor Password
Change User Password
Select Screen
Select Item
Enter Change
F1
F9
F10
ESC
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
5 4
Download from Www.Somanuals.com. All Manuals Search And Download.
3.8
E
x
i
t
S
c
r
e
e
n
BIOS SETUP UTILITY
Main Smart Advanced H/W Monitor Boot Security
Exit
Exit Options
Exit system setup
after saving the
changes.
Save Changes and Exit
Discard Changes and Exit
Discard Changes
F10 key can be used
for this operation.
Would you like to save current setting
user defaults
?
Save 1st User Defaults
Load 1st User Defaults
Select Screen
Select Item
Enter Go to Sub Screen
Save 2nd User Defaults
Load 2nd User Defaults
F1
F9
General Help
Load Defaults
Save and Exit
Exit
Save 3rd User Defaults
Load 3rd User Defaults
F10
ESC
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
Save Changes and Exit
When you select this option, it will pop-out the following message, “Save
configuration changes and exit setup?” Select [OK] to save the changes
and exit the BIOS SETUP UTILITY.
Discard Changes and Exit
When you select this option, it will pop-out the following message, “Dis-
card changes and exit setup?” Select [OK] to exit the BIOS SETUP UTILITY
without saving any changes.
Discard Changes
When you select this option, it will pop-out the following message, “Dis-
card changes?” Select [OK] to discard all changes.
Would you like to save current setting user defaults?
In this option, you are allowed to load and save three user defaults
according to your own requirements.
5 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Software Support
4.1 Install Operating System
This motherboard supports various Microsoft® Windows® operating systems: 2000 /
XP / XP 64-bit / VistaTM / VistaTM 64-bit. Because motherboard settings and hardware
options vary, use the setup procedures in this chapter for general reference only.
Refer to your OS documentation for more information.
4.2 Support CD Information
The Support CD that came with the motherboard contains necessary drivers and
useful utilities that enhance the motherboard features.
4.2.1 Running The Support CD
To begin using the support CD, insert the CD into your CD-ROM drive. The CD
automatically displays the Main Menu if “AUTORUN” is enabled in your computer.
If the Main Menu did not appear automatically, locate and double click on the
file “ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.
4.2.2 Drivers Menu
The Drivers Menu shows the available devices drivers if the system detects
installed devices. Please install the necessary drivers to activate the devices.
4.2.3 Utilities Menu
The Utilities Menu shows the applications software that the motherboard
supports. Click on a specific item then follow the installation wizard to install it.
4.2.4 Contact Information
If you need to contact ASRock or want to know more about ASRock, welcome
dealer for further information.
5 6
Download from Www.Somanuals.com. All Manuals Search And Download.
|