Owner’s
Manual
Model: X7
For Technical Assistance, please call (800) 638-3600,
Download from Www.Somanuals.com. All Manuals Search And Download.
Congratulations on your purchase of a quality Marksman automotive security and remote start
system. Marksman automotive security products have been designed to provide the consumer with
a product that is technologically superior and will provide years of trouble free operation. The
information enclosed will provide a ready reference of the operation and maintenance of your new
Marksman security and remote start system.
Quick Reference Remote Transmitter Operation
Use these illustrations as a reference while
reading through the operating procedures.
Transmitter
Button
System Function
Remark
Lock Doors and Arms System
Arms and Deletes the Shock Sensor
Press Twice within 5 Seconds.
-
Car Locator
Available 30 Seconds after System is Armed
Press and Hold for 3 Seconds
Panic Function (On-Off)
Unlock Doors and Disarm System
Two Steps Door Unlock and Disarm System Press Twice within 3 Seconds
-
Silent Arming/Disarming
Channel 3 (Trunk) Timer Control
Passive Arming By-Pass
Activate Remote Starter
Press both at the same time
+
Press and Hold for 1.5 Seconds
While the System Disarmed.
-
Press / Hold for 1 Second Release. Repeat
Press / Hold for 1 Second Release. Repeat
Press and Release for Car #2 Operation
-
Turn Off the Remote Start
Second System Operation
-
II
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Security System Operation
Manual Lock/Arm
Using The Transmitter To Lock/Arm The Security System
1. Press the
button on the transmitter.
2. The horn and parking lights will chirp/flash once indicating that the system is now armed.
The vehicle’s doors will lock upon arming when interfaced with the security system.
Silent Arming/Disarming:
Pressing the
button on the transmitter will arm or disarm your security system, no chirp
+
sound will be heard, arm/disarm confirmation will be through the vehicles parking lights only.
Defective Sensor Reminder:
If the siren chirps 3 times, you have left open a hood, door or trunk.
Shock Sensor Optional Sensor By-Pass:
Press the
button once, the siren chirps once, the security system is now armed. Press the
button a second time within 5 seconds, the siren chirps twice, the shock sensor is now
bypassed. The sensor bypass feature is programmed to activate for one arming cycle only. The
security system will return to normal operation during the next arming cycle.
Automatic Arming (Optional)
The X7 is equipped with an optional automatic arming feature, which allows the security system
to automatically arm itself 30 seconds after the last door is closed.
1. Turn “OFF” the ignition key and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you
re-open any protected entrance, the security system LED will stop flashing. It will begin
flashing again when the vehicles entrances are closed.
3. After the 30 second timer has elapsed, the security system will automatically “Arm”. The
siren will chirp once and the parking lights will flash once.
Automatic Arming with Automatic Door Locking: (Additional Option)
With this option active, the vehicle’s doors will automatically lock after the automatic arming
cycle has been completed.
Automatic Arming Bypass:
While the LED is flashing for automatic arming or automatic re-arm, press the
button twice,
the security system will respond with 1 chirp and LED will turn “On”. The security system will
remain in this temporary state for as long as you wish. To exit passive bypass, press the
“Lock” or “Unlock” button and the system will return to normal status.
Note: While in Automatic Arming Bypass mode, you will be required to manually arm you
system. Following the “Manual Lock/Arm” procedure above.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Security System Operation (continued)
Manual Unlock/Disarm
Using The Transmitter To Unlock/Disarm The Security System
1. Press the
button on the transmitter.
2. The horn will chirp once and parking lights will flash once indicating that the system is now
disarmed. The vehicle’s door will unlock upon arming when interfaced with the security
system.
Tamper Disarming:
If the security system has been tampered with and activated, the siren will chirp 4 times and
the parking lights will flash 3 times.
Pathway Illumination: (Optional Feature)
This feature turns ”On” the parking lights for 30 seconds upon disarming of the security
system. Arming the security system will leave the parking lights on for 10 seconds.
Two Step Door Unlocking: (Optional Feature)
This feature will independently unlock the driver’s door only when disarming the security system.
Pushing the “Unlock” button a second time within 3 seconds will unlock the entire vehicle.
Automatic Re-Arm: (Optional Feature)
If this feature is selected, the security system will automatically re-arm itself 60 seconds after
disarming with the remote transmitter. Automatic re-arm will cancel if any door is opened
before the 60 second timer has elapsed. Automatic re-arm will also re-lock the doors.
Valet Mode Operation
The valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand
your transmitter to a parking attendant or garage mechanics. When the security system is in “Valet”
mode, all functions and remote start functions are bypassed however, the remote panic feature and
remote door locks will remain operational. To use the “Valet” mode, the security system must first be
disarmed either by using your remote transmitter or by operating the manual override sequence.
Enter Valet Mode:
1. From the disarmed condition, turn the ignition to the “On” position.
2. Push and hold valet switch for 2 seconds or until the “LED” turns on solid. The LED will
remain on as long as the system is in “Valet” mode.
Exit Valet Mode:
1. To return to normal operation, turn the ignition switch “On”.
2. Push and hold the valet switch for 2 seconds and the “LED” will turn off. This indicates the
security system is out of the “Valet” mode.
Emergency Override Operation
The override function may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to “On” position.
2. Within 10 seconds push and release the valet switch, the security system will enter the
“Emergency Override” mode. You can now start and operate the vehicle normally.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Security System Operation (continued)
Remote Panic Alarm Operation
The transmitter can be used as a remote panic switch to manually trigger the alarm in case of
emergency.
1. Press and hold the
button for 3 seconds. The alarm will immediately sound.
button on the transmitter.
button is pressed for panic, the car finder feature will trigger first then the
2. To stop the security system from the “Panic” mode, press the
Note: When the
panic function will activate.
Trigger the System (Shock Sensor and Entrance Protection)
When the X7 is armed, your vehicle is protected by the shock sensor as follows:
1. Light impacts to the vehicle body will trigger the pre-warning signal from the shock sensor.
A long chirp from siren/horn.
2. Heavy impacts, a door is opened, the hood is opened, the trunk is opened or the ignition key
is turned on will trigger the horn/siren. The starter disable relay (if installed) will prevent the
vehicle’s starter from cranking. The trigger cycle will last for 30 seconds then it will stop and
automatically re-set and re-arm. If one of the sensors or detectors are still active the security
system will sound a maximum of 6 times for a 30 second cycles.
Interior Light Convenience Supervision (Option)
If this option has been installed, it will operate in the following manner:
1. Upon disarming, the interior lights will remain on for 30 seconds.
2. If the vehicle is intruded, the interior light will flash for the same duration as the siren.
Note: Turn on the ignition switch or arm the security system and it will turn off the dome light.
Ignition Key Lock Control (Option)
If the vehicles door locks have been interfaced to the security system, the security system will
automatically lock the vehicle’s doors when the ignition is turned “On” and/or unlock the vehicle’s
door when the ignition is turned “Off”. (Programming is required for this feature to be active).
Trunk Release (Option)
Press and hold the
button on the transmitter for 1.5 seconds to activate the trunk release or
other electronic devices.
Car Locator
The car locator feature of the X7 is progressive. After the X7 has been armed for 30 seconds,
press the button to activate the car locator function. The siren/horn will sound 2 times and
pause then sound two more times. The parking lights will flash 3 + 3 times. Press the
button a
second time and the siren/horn will sound 3 times and pause then sound four more times. The
parking lights will flash 3 + 3 times. Press the button a third time and the siren/horn will sound
6 times The parking lights will flash 6 times.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Start Operation
User Warnings
As with any product that performs automatic functions, there are certain safety precautions that
you must practice and be aware of.
1. Keep the transmitter out of reach of children.
2. DO NOT leave anyone in the vehicle while running on remote control.
3. Alert any service personal that the vehicle can be started automatically.
4. DO NOT start the vehicle by remote while it’s in an enclosed area or garage.
5. Always apply the parking brake and lock the vehicle as you exit the vehicle.
6. Should the unit malfunction, disconnect the fuse until the problem is corrected.
7. The use and operations of this security system is the sole responsibility of the
owner/operator of the vehicle.
8. Some areas may have local ordinances that prohibit leaving a vehicle running on public
streets. Check your local laws and ordinances.
How to Remote Start Your Vehicle
1. Press the
button twice on the transmitter for about 1 second.
2. The parking lights will activate to indicate the remote start signal has been received.
3. The engine will start in approximately 5 seconds.
4. Once the engine is running, after 11 seconds the parking lights will turn on again and climate
controls will activate and adjust the vehicle’s interior temperature to your preset setting.
5. The vehicle will run for 5 to 30 minute cycle and automatically shut down.
Note: The remote start unit will not start the vehicle if any one of the following conditions exists:
1. The hood is open.
2. The brake pedal is pressed.
3. Move the optional remote start enable switch to “Off” position (if installed).
4. The gear selector is in any gear other than “Park” or “Neutral”.
How to Operate the Vehicle While Running on Remote Start
1. Insert the ignition key and turn it to the “On” position. Be sure you DO NOT turn the ignition
key all the way to the “Start” position. This can cause severe damage to all the starter
components on your vehicle.
2. Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the “On” position, the engine will
automatically shut down.
Temporary Stop Operation
This feature allows the vehicle to remain running after the key has been removed from the
ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short
periods of time but, would like to leave the motor running and climate control on.
1. Before turning off the engine, press the
button twice on the transmitter and the LED
indicator will flash 3 times to confirm mode entry.
2. Turn the ignition key to “Off” position (The engine will stay running).
3. The engine will run until the pre-programmed time elapsed or shutdown input is received.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Start Operation (continued)
Timer Starting
This unit can be programmed to start and run the engine every 2 or 3 hours. The engine will run
for the programmed run time and then shut down. This feature is designed for an extreme cold
climate. The system will automatically start the vehicle every 2 or 3 hours to prevent engine from
cold hard to start and freezing over. A MAXIMUM OF SIX CYCLES CAN OCCUR.
Important: Timer start should be used in open areas, never start and run the vehicle in enclosed
spaces as a garage or carport
To Activate the Start Timer:
1. Press the
the parking lights have turned on or flashing.
2. Immediately depress the button then depress the
button twice to remote start the vehicle. As soon as the vehicle is running and
button. The parking lights will flash
(3) times. The siren or horn chirps (3) times. The vehicle is now programmed to start
every 2 or 3 hours.
3. Press the brake pedal to stop the vehicle from running.
Note: Unless the installer of this remote start system has reprogrammed the start timer for a 2 hour
duration, the default programmed start time is set to 3 hours.
Exit the Timer Start:
Timer start can be exited manually as follows:
1. Make sure the remote start system is not operating the engine.
2. Turn the ignition to the “On” position. The LED and parking lights will flash (4) times. The
horn or siren chirps (4) times.
or
1. Press the
the parking lights have turned on or flashing.
2. Immediately depress the button then press and hold the
button twice to remote start the vehicle. As soon as the vehicle is running and
button for 2 seconds. The
parking lights will flash (4) times. The siren or horn chirps (4) times. The vehicle is no
longer programmed to start automatically.
Shut-Down Inputs for Remote Starter
If any of the following conditions exist while the system is operating, the engine will not start or
will shut down:
1. The hood is open.
2. The brake pedal is pressed.
3. Move the optional remote start enable toggle switch to “Off” position (If installed).
4. Engine is over-revved (Tachometer Checking Type).
5. The pre-programmed run time 5-10-20-30 minutes has elapsed.
6. Transmitter
button is pressed twice.
7. The vehicle refused to start running after 3 unsuccessful attempts.
Disabling the Remote Start System
This feature allows your security system’s remote start unit to be temporarily disabled to prevent
the vehicle from being remote started accidentally. This feature is useful if the vehicle is being
serviced or stored in an enclosed area. To disable the remote start, move the optional remote
start enable toggle switch to the “Off” position. (If installed)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Start Operation (continued)
Turbo Timer Mode (Also See Installation Manual)
Turbo Timer mode keeps the engine running after arriving at you destination for a programmable
time period of 1, 3 or 5 minutes. This allows the system’s time to conveniently cool down the
turbo after you have left the vehicle.
To Activate:
1. While the engine is running, set the emergency brake and place the transmission to "Park".
2. Before turning off the engine, press and release and buttons at the same time. The light
will flash to indicate the remote start has entered “Turbo Timer” mode.
3. Remove the “Ignition Key” from the key cylinder. The engine will keep running.
4. Exit and secure the vehicle. The engine continues running until the pre-programmed time
elapsed.
Chirp Status Indications
Parking Light Flash Indications
Chirp
Function
Parking Lights
1 Flash
Function
1 Chirp
2 Chirps
3 Chirps
4 Chirps
6 Chirps
Arm
Arm
Disarmed
2 Flashes
Disarmed
Defective Reminder
Disarm / Triggered
Car Locator
3 Flashes
Disarm / Triggered
Car Locator
Under Remote Control
12 Flashes
Constant On
Alarm Operating Conditions
Siren, Horn
Parking Light LED
Doors
Starter
Disable
Dome Light
1. Arming
1 or 3 Chirps 1 Flash
Slow Flash Locking
2. Disarming 2 or 4 Chirps 2 or 3 Flashes Fast Flash
Unlocking
Turns on for 30 Seconds
3. Trigger
4. Panic
Alarming
Alarming
Flashes
Slow Flash
Disable Flashes
Flashes
Flashes
5. Car Locator 6 Chirps
12 Flashes
LED Status Indications
LED
Function
LED
Function
Off
Disarmed
Armed
2 Flashes... pause
3 Flashes... pause
4 Flashes... pause
5 Flashes... pause
Zone 2: Trigger on Trunk/Hood
Zone 3: Trigger on Door Switch
Zone 4: Trigger on Optional Sensor
Zone 5: Trigger on Ignition Switch
Slow Flash
Fast Flash
On (Solid)
Passive Arming
Valet Mode
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement Parts and Accessories for
Remote Mobile Security Systems
DESCRIPTION
MODEL #
$ PRICE
ORDER BY MAIL
Uses 3 volt CR2032 Lithium Battery (2 pcs.)
Replacements:
CR2032
Radio Shack: #23-162 (CR22032)
Duracell: #DL2032
Eveready: #ECR2032
Panasonic: # CR2032
4-Button Transmitter with SAW
Technology for:
X7RF
$44.95 ea.
X7 Remote Start Security System.
6-Tone, 118dB Siren: For use with all
Remote Mobile Security Systems.
ALA115
ALA125
$34.95 ea.
$39.95 ea.
6-Tone, 130dB Siren: For use with all
Remote Mobile Security Systems.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and Accessories Order Form
Mail to: Magnadyne Corporation
Credit Card or Money Order Only
ATTN: Consumer Parts Sales
P.O. Box 5365
Carson, CA 90749-5365
(Sorry No Cash, C.O.D. or personal checks accepted)
SHIP TO: (No P.O. Boxes)
LAST NAME
FIRST NAME
INITIAL
STREET ADDRESS
ADDITIONAL ADDRESS
ADDITIONAL ADDRESS
CITY
STATE
ZIP CODE
DAY TIME PHONE NUMBER
CREDIT CARD INFORMATION
VISA
MC
CREDIT CARD N0.
CARD HOLDER’S LAST NAME
STREET ADDRESS
CITY
EXPIRATION DATE
FIRST NAME
INITIAL
STATE
QTY.
ZIP CODE
PART #
DESCRIPTION
PRICE EACH
TOTAL
Shipping and Handling
Sales Subtotal = ________ . ______
Up to $20.00
20.01 to 30.00
30.01 to 45.00
45.01 to 70.00
Over 70.01
$5.00
5.95
6.50
6.95
7.95
California Residents Add Sales Tax = ________ . ______
Shipping and Handling (See Chart) = ________ . ______
TOTAL = ________ . ______
On regular orders please allow 4-5 weeks for delivery.
Please give a shipping address where this order may be delivered between the hours of 9 a.m. and 5 p.m. weekdays.
If UPS is unable to deliver, your order will be returned and additional shipping charges will be required.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Lifetime Warranty
Magnadyne Corporation or its authorized agents will, for the life of the vehicle and to the original
purchaser, repair, replace or refund the retail sales price of said product or any part thereof, at the
option of the Magnadyne Corporation or its authorized agents, if said product or part is found
defective in materials or workmanship, when properly connected and operating on the correct
power requirements designated for the specific product. This warranty and Magnadyne Corporation
or its authorized agents obligations, hereunder do not apply where the product was: damaged while
in the possession of the consumer, subjected to unreasonable or unintended use, not reasonably
maintained, utilized in commercial or industrial operation, or serviced by anyone other than
Magnadyne Corporation or its authorized agent, or where the warning seal on the product is broken
or the power plugs or wires are detached from the unit. Magnadyne Corporation or any of its
authorized agents do not assume any labor costs for the removal and reinstallation of any product
found to be defective, or the cost of transportation to Magnadyne Corporation or its authorized
agents. Such costs are the sole responsibility of the purchaser.
This warranty does not cover the cabinet, appearance items, normal wear and tear or accessories
used in connection with the product resulting from improper installation, alteration, accident, misuse,
abuse or acts of nature.
This Limited Life Time Warranty applies only to the receiver section of the security system. Neither
the siren, transmitters, wire harness or any accessory item added to or used with a Remote Mobile
security system are covered by this Limited Life Time Warranty. Sirens, transmitters, wire harness
or any accessory item are covered by our standard 12 month limited warranty.
Magnadyne Corporation or its authorized agents shall not be liable to anyone for consequential
or incidental damages or claims that may arise due to failure of product to operate properly
except those accorded by law. Magnadyne's or its authorized agents liability to the repair,
replacement of the product as stated above if all conditions of the warranty are met. No
expressed warranty or implied warranty is given except those set forth herein. Magnadyne does
not warrant or guarantee against break in damage or the theft of the vehicle in part or whole, or
against the loss or damage to the contents of any vehicle in which a security system is installed.
Magnadyne security systems are only a deterrent against possible theft.
This warranty extends only to the original purchaser of the product and for the vehicle in which it
was originally installed. This warranty is not transferable or assignable to any person or vehicle.
Defective merchandise should be returned to the original point of purchase or secondly to
Magnadyne Corporation, 1111 W. Victoria Street, Compton, CA 90220. A return authorization must
be obtained before sending, or merchandise may be refused.
Download from Www.Somanuals.com. All Manuals Search And Download.
© Copyright 2008 Magnadyne Corporation
X7-UM 3-11-08 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|