O W N E R ’ S
M A N U A L
Model: 7960DTL
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference; and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to
this equipment. Such modifications could void the user’s authority to operate the equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
Program a User Code
To Program the User Code, Repeat the Following Steps:
1. All vehicle security systems must be in disarmed mode prior to tap-code programming.
2. Decide what your new user code will be before starting the programming sequence. The user code
must be a minimum of (3) digits and a maximum of (5) digits.
Note: Default user code is 11111.
3. Set the ignition key from the “Off” position to On - Off - On (Ignition is on).
4. Press and release the black rubber button on the tap sensor (3) times.
5. In an area close to the tap sensor, tap the vehicle glass (2) times. The tap sensor will flash “0” - “0”
and then start to display digits from 1-5.
6. Tap on the glass (1) time when the first digit of your unlock code is shown. The digit will flash twice to
confirm that it has been selected. The tap sensor will start to display numbers from 1 to 5 again. Tap
on the glass (1) time for each remaining digit of your user code.
7. When you are done “tap-selecting” your user code, set the ignition key to the Off position. The tap
sensor will flash “0” - “0” and then display the new code you have entered. The tap sensor will repeat
the “0” - “0” flash and display the new code a second time.
To Unlock Your Vehicle
1. Tap on the vehicles windshield near the location of the tap sensor 2 times. The tap sensor will display
“0” - “0” and then will start to display numbers from 1 to 5, pausing for 1 second between each
number.
2. Tap on the glass 1-time when the first digit of your unlock code is shown. The digit will flash twice to
confirm that it has been selected.
3. The tap sensor will start to display numbers from 1 to 5 again. Tap on the glass 1- time for each
remaining digit of your user code.
4. When the correct code has been “tap-selected”, the display will show “C” and the doors will unlock.
5. If a mistake was made in the digit selection process, the display will show “E” and start displaying
numbers from 1 to 5 again. Repeat steps 2-3.
6. The following unsuccessful code entry attempts will lock the tap sensor out for 1 minute:
If your code is 3 digits, 3 unsuccessful attemps,
If your code is 4 digits, 4 unsuccessful attemps,
If your code is 5 digits, 5 unsuccessful attemps.
Note: Cycling the ignition key on-off will reduce this time.
Recalling the Programmed Tap Code
In the event you forgot your tap code, repeat the following procedure to recall the programmed tap-code:
1. Set the ignition key from the “Off” position to On - Off - On (Ignition is on).
2. Press and release the black rubber button on the tap sensor (6) times.
3. The tap sensor will display the current tap-code starting with “0” - “0”. The code will be displayed
twice.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
3 Year Warranty
Your new Silencer® Security Systems is warranted to be free of defects for 3 years. Silencer®
or its authorized agents will within 3 years from the date of sale to you, repair or replace said
product or any part thereof, at the option of the Silencer® or its authorized agents, if said
product or part is found defective in materials or workmanship, when properly connected and
operating on the correct power requirements designated for the specific product. This warranty
and Silencer® or its authorized agents obligations hereunder do not apply where the product
was; damaged while in the possession of the consumer, subjected to unreasonable or
unintended use, not reasonably maintained, or serviced by anyone other than Silencer® or its
authorized agents, or where the warning seal on the product is broken or the power and/or
plugs are detached from the unit. This warranty does not cover the cabinet appearance items or
accessories used in connection with this product, or any damage to the products resulting from
improper installation, alteration, accident, misuse, abuse or acts of nature. Silencer® OR ITS
AUTHORIZED AGENTS SHALL NOT BE LIABLE TO ANYONE FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE ACCORDED BY LAW. NO EXPRESSED
WARRANTY OR IMPLIED WARRANTY IS GIVEN EXCEPT THOSE SET FORTH HEREIN. NO
IMPLIED WARRANTY SHALL EXTEND BEYOND 3 YEARS FROM THE DATE OF SALE. Some
states do not allow limitations on how long an implied warranty lasts, and some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitations
or exclusion may not apply to you. This warranty gives you specific legal rights, and you may
have other rights that vary from state to state. Defective merchandise should be returned to the
original point of purchase or secondly, to 1111 W. Victoria Street, Compton CA 90220. Return
Authorization must be obtained before sending, or merchandise may be refused. All claims
concerning your Silencer® Security System should be referred to your selling dealer. If you are
away from the vicinity of the selling dealer please call (800) 340-3200.
© 2008 Copyright Magnadyne Corp.
7960DTL-UM 4-7-08 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|