RADIANCE
SONET
SINGLE INTERFACE LINE CARDS
OC-3
OC-12
OC-3
PWR
PWR
PWR
R
X
LK
R
X
LK
R
X
LK
M
M
M
M
M
M
T
X
T
X
T
X
LK
R
X
LK
R
X
LK
R
X
L
H
S
M
S
M
T
X
T
X
T
X
Installation & User Guide
Models: R125-34 / R125-37 / R135-34
Download from Www.Somanuals.com. All Manuals Search And Download.
RTadaiancbe SlOeNET oSingfle ICnterfaocenLinetCeardns Intsstallation
& User Guide
Overview ............................................................................................................. 4
Installation Guide ............................................................................................... 5
STEP 1: Unpack the Line Card ........................................................... 5
STEP 2: Set the DIP Switches ............................................................. 5
STEP 3: Install the Line Card.............................................................. 8
STEP 4: Connect to the Network ........................................................ 8
User Guide .......................................................................................................... 9
LED Indicators .................................................................................... 9
Link Loss Return (LLR).................................................................... 10
Link Loss Carry Forward (LLCF)..................................................... 11
Topology Solutions ........................................................................... 12
Technical Specifications .................................................................... 13
Product Safety, EMC and Compliance Statements ........................... 14
Warranty and Servicing ..................................................................... 15
Metrobility, Metrobility Optical Systems, and NetBeacon are registered trademarks of Metrobility Optical
Systems, Inc. The Metrobility Optical Systems logo is a trademark of Metrobility Optical Systems, Inc.
The information contained in this document is assumed to be correct and current. The manufacturer is
not responsible for errors or omissions and reserves the right to change specifications at any time
without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
The Radiance SONET single interface line card provides seamless
integration between fiber optic multimode and singlemode segments in OC-3/
STM-1 or OC-12/STM-4 networks. Use the card’s singlemode connector to
extend your network reach up to 40 km.
The Radiance line card is manageable through console commands, Metrobility’s
GUI-based NetBeacon® or WebBeacon software, or any SNMP application. This
ability provides software control over the card’s configuration and notification
of a failure to a management station.
The Radiance SONET single interface line card offers the following key
features:
•
Two Link Loss Return (LLR) switches and Link Loss Carry
Forward (LLCF) to aid in troubleshooting remote network
connections.
•
•
•
Full-duplex support.
OC-3/STM-1 (155Mbps) and OC-12/STM-4 (622Mbps) support.
A link LED on each port to indicate that the port is receiving a
signal.
•
Reliable data transmission over multimode cables up to 2 km and
singlemode cables up to 40 km.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Guide
Follow the simple steps outlined in this section to install and start using
your Radiance SONET single interface line card.
NOTE: Electrostatic discharge precautions should be taken when handling any
line card. Proper grounding is recommended (i.e., wear a wrist strap).
Unpack the Line Card
Your order has been provided with the safest possible packaging, but
shipping damage does occasionally occur. Inspect your line card
carefully. If you discover any shipping damage, notify your carrier and
follow their instructions for damage and claims. Save the original
shipping carton in case return or storage of the unit is necessary.
1
Set the DIP Switches*
A set of six DIP switches is located on the back of the line card. (See
illustration.) Two of these switches are used to enable/disable Link
Loss Return (LLR) and are clearly marked LLR1 and LLR2 on the
printed circuit board.
2
The remaining switches, including the one labeled LLCF, are nonfunc-
tional. Pushing these switches up and down has no effect. Link Loss
Carry Forward (LLCF) is a feature that is always enabled.
When setting DIP switches, the UP position is when the lever of the
DIP switch is pushed away from the circuit board. The DOWN position
is when the lever is pushed toward the circuit board.
The default switch settings are LLR1 disabled (DOWN) and LLR2
disabled (DOWN).
*DIP switches also can be controlled by console commands or with Metrobility’s NetBeacon or WebBeacon management
software. Refer to the Command Line Interface Reference Guide, NetBeacon Element Management Software Installation & User’s
Guide or WebBeacon Management Software Installation & User’s Guide for software management information.
Radiance SONET Single Interface Line Cards
5
Download from Www.Somanuals.com. All Manuals Search And Download.
LLCF
DIP switches
LLR1
LLR2
1000BASE
PWR
SX
R
X
LK
M
M
Port 1
Port 2
T
X
LK
R
X
S
M
T
X
LX
Power Connector
Link Loss Return Switches
The Radiance SONET single interface line card incorporates Link Loss
Return (LLR) functionality as an aid in troubleshooting remote
connections. LLR is enabled independently on each port. When LLR is
enabled on a port, loss of its receive (RX) link disables its own transmit
(TX) link.
LLR1 enables/disables Link Loss Return on Port 1, and LLR2 enables/
disables the function on Port 2. To enable Link Loss Return for a port,
set its LLR switch ON (up). Set the switch OFF (down) to disable the
function.
For more information, refer to Link Loss Return in the User Guide
section of this manual.
6
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the Line Card
The Radiance SONET single interface line card offers the ease of plug-
and-play installation and is hot-swappable. All cards must be firmly
secured to the chassis before network connections are made. Follow the
simple steps outlined below to install your line card.
3
Slot for Management Card
Card Guide
10/100
PWR
10/100
PWR
10/100
PWR
O
C
-12
1000BASE
PWR
1000BASE
PWR
OC-12
PWR
10/100
10/100
PWR
10/100
PWR
10/100
PWR
OC-12
PWR
OC-12
PWR
OC-12
PWR
P
W
R
MGT-10
FL
FL
FL
FL
LK
AT
LK
AT
100
FD
RX
100
FD
RX
1
2
SX
SX
R
X
LK
LK
R
X
LK
RX
LK
TX
RX
LK
TX
RX
LK
TX
LK
RX
R
X
LK
R
X
LK
R
X
LK
T
X
T
X
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
OC-3
M
M
M
M
M
LK
TX
LK
TX
PWR
T
X
T
X
T
X
T
X
T
X
x
II
x
II
LX
R
X
LK
x
II
x
II
PWR
LK
LK
LK
LK
LK
LX
R
X
LK
LK
R
X
RX
RX
LK
TX
A
B
RX
LK
TX
RX
LK
TX
RX
LK
TX
R
X
R
X
R
X
R
X
M
M
C
O
N
S
O
L
M
M
S
S
M
S
M
S
M
M
M
S
M
S
M
S
M
T
X
M
T
X
T
X
T
X
T
X
T
X
T
X
T
X
T
X
R
E
100
FD
100
FD
FX
FX
LK
FX
ER
LX
R
X
S
M
T
X
IMPORTANT!
Tighten thumb screw
Thumb Screw
Card Guide
to secure each card firmly
to chassis before making
network connections.
Blank Panel
•
•
Grasp the card by the front panel as shown.
Insert the card into a slot on the chassis making sure that the
top and bottom edges of the board are aligned with the top and
bottom card guides in the chassis. Do not force the card into
the chassis unnecessarily. It should slide in easily and evenly.
•
•
Slide the card in until the top and bottom edges of the front
panel are flush and even with the top and bottom edges of the
chassis.
To secure the line card to the chassis, turn the thumbscrew
clockwise until it is snug. The card is now properly installed
and ready for connection to the network.
Radiance SONET Single Interface Line Cards
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect to the Network
To connect the Radiance line card to the network, insert the fiber optic
cables into the appropriate SC connectors. (See the figure below.) Be
sure the card is secured to the chassis before making network connec-
tions.
4
When making network connections, make sure that the transmit (TX)
optical conductor of the line card connects to the receive (RX) optical
conductor of the connected device; and be sure that the transmit (TX)
optical conductor of the device connects to the receive (RX) optical
conductor of the card.
Port 1 is the multimode (MM) interface. The OC-3/STM-1 models
support a maximum segment length of 2 km. The OC-12/STM-4 line
card supports a maximum segment length of 500 m.
Port 2 is either a singlemode (SM) or singlemode long haul (LH)
interface. The SM port supports a maximum segment length of 15 km,
and the LH port supports a maximum segment length of 40 km.
Once power is applied to the unit, correct connectivity can be verified
via the link (LK) LED.
OC-3
PWR
OC-12
PWR
OC-3
PWR
OC-12
PWR
OC-3
PWR
R
X
LK
LK
LK
R
X
LK
R
X
LK
R
X
R
X
M
M
M
M
M
M
M
M
M
M
T
X
T
X
T
X
T
X
T
X
R
X
LK
LK
LK
L
R
X
R
X
R
X
LK
R
X
S
M
S
M
L
H
L
H
T
X
T
X
X
T
X
T
X
LX
8
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
This sec
s
tion
e
cont
r
ains m
G
ore info
u
rmati
i
on
d
regarding the operating features of
e
the Radiance SONET single interface line card.
LED Indicators
The Radiance SONET single interface line card provides three LEDs on the
front panel for the visible verification of unit status and proper functionality.
These LEDs can assist with troubleshooting and overall network diagnosis and
management.
When lit, the LEDs indicate the following status:
• PWR (power): The unit is powered ON.
• LK (Port 1): Port 1 is receiving valid input light level.
• LK (Port 2): Port 2 is receiving valid input light level.
Radiance SONET Single Interface Line Cards
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Link Loss Return (LLR)
Both ports on the Radiance SONET single interface line card have been de-
signed with LLR for troubleshooting a remote connection. When LLR is
enabled*, the port’s transmitter shuts down if its receiver fails to detect a valid
receive link. LLR should only be enabled on one end of a cable and is typically
enabled on either the unmanaged or remote device. LLR works with in conjunc-
tion with Link Loss Carry Forward.
The diagram below shows a typical network configuration with good link status
using two SONET line cards for remote connectivity. Note that LLR is enabled
as indicated in the diagram.
Management Switch/Hub
Station w/SNMP
Switch/Hub Remote
w/SNMP Station
SONET
Line Card A
SONET
Line Card B
LLR2 is ON
LLR1 is OFF
LLR2 is ON
LLR1 is OFF
Remote
Cable
Port 2 Port 1
Port 2 Port 1
LED lit = established link
LED unlit = no link
Example: If one of the optical conductors breaks (as shown in the diagram box
below), Line Card B, with LLR2 enabled, will return a no-link condition to its
link partner, Line Card A. Because the line cards are designed with LLCF
functionality, the no-link condition is carried forward to the switch/hub where a
trap is generated to the management station. The network administrator can then
determine the source of the loss.
Management
Station
SONET
Line Card A
Switch/Hub
w/SNMP
Switch/Hub Remote
w/SNMP Station
SONET
Line Card B
LLR2 is ON
LLR1 is OFF
LLR2 is ON
LLR1 is OFF
Broken
Conductor
Port 1
Link Loss Carried Forward
Port 2
Link Loss Carried Forward
Link Loss Returned
LED lit = established link
LED unlit = no link
IMPORTANT: LLR must not be active on both ends of a configuration. If it is,
the link can never be established.
*Units are shipped with the LLR function disabled (DOWN).
10
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Link Loss Carry Forward (LLCF)
The Radiance SONET single interface line card incorporates LLCF for trouble-
shooting a remote connection. With LLCF, the ports do not transmit a signal
until they receive a signal from the opposite port. For example, if a line card
loses link on Port 2, the card will not transmit link pulses out of Port 1.
The diagram below shows a typical network configuration with good link status
using SONET line cards for remote connectivity.
Management Switch/Hub
Station w/SNMP
Switch/Hub Management
w/SNMP Station
SONET
Line Card
SONET
Line Card
Remote
Cable
LED lit = established link
LED unlit = no link
If a connection breaks, the line cards carriy that link loss forward to the switch/
hub which generates a trap to the management station. The network administra-
tor can then determine the source of the problem.
Management Switch/Hub
Station w/SNMP
Switch/Hub Management
w/SNMP Station
SONET
Line Card
SONET
Line Card
Broken
Remote
Cable
Link Loss Carried Forward
Link Loss Carried Forward
LED lit = established link LED unlit = no link
Management Switch/Hub
Station w/SNMP
Switch/Hub Management
w/SNMP Station
SONET
Line Card
SONET
Line Card
Remote
Cable
Broken
Cable
Link Loss Carried Forward
LED unlit = no link
LED lit = established link
Radiance SONET Single Interface Line Cards
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Topology Solutions
Servers
Switch
PC running Network
Management Software
Radiance R5000 Central
Service Platform with
SONET Single Interface
Line Cards
Workgroup Hub
remote connection — singlemode
Switch
Enterprise Switch
Enterprise
Multimode Links
Singlemode Links
12
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
Power
Budget
(TX
Fiber
Type
and
Cable
Size
Core/
Clad
RX
Input
Power Power
(min) (sat)
RX
Input
TX
TX
Wave
Length Length
Cable
Output
Power
(min)
Output
Power
(max)
Protocol
Pwrmin
-
Models
RX
Pwrmin
)
50µm/
125µm
-30dBm -14dBm -23.5dBm -14dBm 6.5dBm
MM
2km
(rated)
(R125-34/ 1310nm
R125-37)
62.5µm/
125µm
-30dBm -14dBm -20dBm -14dBm
10dBm
20dBm
30dBm
15km
(rated,
1310nm based on
power
OC-3/
STM-1
SM
(R125-34)
9µm/
125µm
-35dBm -8dBm -15dBm
-8dBm
budget)
SM LH
(R125-37)
40km
1310nm
9µm/
125µm
-35dBm 0dBm
-5dBm
0dBm
(rated)
50µm/
125µm
-26dBm -14dBm -22.5dBm -14dBm 3.5dBm
-20dBm
500m
1310nm
MM
SM
(rated)
OC-12/
STM-4
62.5µm/
125µm
-26dBm -14dBm
-14dBm
6dBm
(typical)
15km
1310nm
9µm/
125µm
-28dBm -7dBm -15dBm
-8dBm
13dBm
(rated)
Data Rate
Data Rate _____________ 155Mbps (OC-3/STM-1), 622Mbps (OC12/STM-4)
Power Consumption
Input ______________________________________________ 5V @ 0.8A, 4W
Environmental
Operating Temperature ____________________________________ 0° to 50° C
Storage Temperature ____________________________________ -30° to 70° C
Operating Humidity _________________________ 5% to 95% non-condensing
Weight_______________________________________________ 5 oz (0.14 kg)
Radiance SONET Single Interface Line Cards
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Safety, EMC and Compliance
Statements
This equipment complies with the following requirements:
• UL
• CSA
• EN60950 (safety)
• FCC Part 15, Class A
• EN55022 Class A (emissions)
• EN50082-1 (immunity)
• IEC 825-1 Classification
• Class 1 Laser Product
• DOC Class A (emissions)
This product shall be handled, stored and disposed of in accordance with all
governing and applicable safety and environmental regulatory agency require-
ments.
The following FCC and Industry Canada compliance information is applicable
to North American customers only.
USA FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equip-
ment is operated in a commercial environment. This equipment generates, uses
and can radiate radio frequency energy, and if not installed and used in accor-
dance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Caution: Changes or modifications to this equipment not expressly approved by
the party responsible for compliance could void the user’s authority to operate
the equipment.
Canadian Radio Frequency Interference Statement
This Class A digital apparatus meets all requirements of the Canadian Interfer-
ence-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du
Réglement sur le matériel brouilleur du Canada.
14
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Servicing
Three-Year Warranty for Radiance SONET Single Interface Line Card
Metrobility Optical Systems, Inc. warrants that every Radiance SONET single
interface line card will be free from defects in material and workmanship for a
period of THREE YEARS from the date of Metrobility shipment. This warranty
covers the original user only and is not transferable. Should the unit fail at any
time during this warranty period, Metrobility will, at its sole discretion, replace,
repair, or refund the purchase price of the product. This warranty is limited to
defects in workmanship and materials and does not cover damage from accident,
acts of God, neglect, contamination, misuse or abnormal conditions of operation
or handling, including overvoltage failures caused by use outside of the
product’s specified rating, or normal wear and tear of mechanical components.
To establish original ownership and provide date of purchase, complete and
return the registration card or register the product online at
www.metrobility.com. If product was not purchased directly from Metrobility,
please provide source, invoice number and date of purchase.
To return a defective product for warranty coverage, contact Metrobility
Customer Service for a return materials authorization (RMA) number. Send the
defective product postage and insurance prepaid to the address provided to you
by the Metrobility Technical Support Representative. Failure to properly protect
the product during shipping may void this warranty. The Metrobility RMA
number must be clearly on the outside of the carton to ensure its acceptance.
Metrobility will pay return transportation for product repaired or replaced in-
warranty. Before making any repair not covered by the warranty, Metrobility
will estimate cost and obtain authorization, then invoice for repair and return
transportation. Metrobility reserves the right to charge for all testing and
shipping costs incurred, if test results determine that the unit is without defect.
This warranty constitutes the buyer’s sole remedy. No other warranties, such as
fitness for a particular purpose, are expressed or implied. Under no circum-
stances will Metrobility be liable for any damages incurred by the use of this
product including, but not limited to, lost profits, lost savings, and incidental or
consequential damages arising from the use of, or inability to use, this product.
Authorized resellers are not authorized to extend any other warranty on
Metrobility’s behalf.
Radiance SONET Single Interface Line Cards
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Manuals
The most recent version of this manual is available online at
Product Registration
To register your product, go to
25 Manchester Street, Merrimack, NH 03054 USA
tel: 1.603.880.1833 • fax: 1.603.594.2887
5660-000018 D
3/04
Download from Www.Somanuals.com. All Manuals Search And Download.
|