IDE 4000 Flash Disk
1.8" and 2.5"
Product Specification and User Manual
January 2005
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
1. Specifications........................................................................................................................5
1.1. Critical Item Definition ....................................................................................................5
1.2. Characteristics................................................................................................................5
1.2.1. Interface Definition...........................................................................................................5
1.2.2. IDE Transfer Modes......................................................................................................... 5
1.2.3. Performance .................................................................................................................... 5
1.2.4. Access Time ....................................................................................................................6
1.2.5. Seek Time........................................................................................................................ 6
1.2.6. Input Voltage.................................................................................................................... 6
1.2.7. Current Consumption....................................................................................................... 6
1.2.8. Memory Capacity............................................................................................................. 7
1.2.9. Endurance........................................................................................................................ 8
1.2.10. Mean Time Between Failures (MTBF)............................................................................. 8
1.2.11. Physical Characteristics................................................................................................... 8
1.3. Environmental Conditions ............................................................................................11
1.3.1. Temperature .................................................................................................................. 11
1.3.2. Altitude........................................................................................................................... 12
1.3.3. Relative Humidity........................................................................................................... 12
1.3.4. Shock............................................................................................................................. 12
1.3.5. Vibration......................................................................................................................... 12
1.3.6. Storage Life and Data Retention ................................................................................... 12
2. Drive Configuration.............................................................................................................13
3. Interface Connectors ..........................................................................................................14
4. Supported IDE Commands.................................................................................................15
5. CE and FCC Compatibility..................................................................................................16
6. Label Information................................................................................................................17
7. Using the IDE 4000 Flash Disk...........................................................................................18
7.1. Unpacking the Drive.....................................................................................................18
7.2. Handling Instructions....................................................................................................18
7.3. Installing the Drive in a PC...........................................................................................18
7.4. Using the IDE 4000 in an MS-DOS-Based Platform ....................................................19
7.5. Troubleshooting ...........................................................................................................19
7.6. How to Get Help...........................................................................................................20
3
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Warranty...............................................................................................................................21
9. Ordering Information ..........................................................................................................22
How to Contact Us....................................................................................................................23
4
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
1. SPECIFICATIONS
1.1. Critical Item Definition
The dimensions of the IDE 4000 flash disk enable mounting in a standard 2.5”or 1.8” disk drive
Note: The information written in this document refers to both IDE 4000 2.5” and 1.8” unless
otherwise stated.
1.2. Characteristics
1.2.1.
1.2.2. IDE Transfer Modes
Interface Definition
The IDE 4000 supports the following transfer modes:
• PIO modes 0 through 4
• DMA modes 0 through 2
1.2.3.
Performance
The IDE 4000 complies with the performance requirements described in Table 1.
Table 1: IDE 4000 Transfer Rates
Operation
Read
Burst Rate (MB/sec)
Sustained Rate (MB/sec)
16.6
16.6
3.8
3.4
Write
Performance was measured on a system with the following configuration:
• Computer with ASUS P4T533-C motherboard and Intel 2.4 GHz processor
• Windows XP Professional operating system
• IDE transfer mode: Multiword DMA 2
• IDE 4000 disk capacity: 4GB
The HDTACH v2.61 benchmark utility was used to measure IDE 4000 performance. See
Figure 1 for measurement results.
5
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1: IDE 4000 Performance Results
1.2.4.
Standby to active (typical.): 0.1 msec
1.2.5. Seek Time
The IDE 4000 has no seek time, as it has no moving parts.
1.2.6. Input Voltage
The IDE 4000 input voltage is 3.3VDC to 5.0VDC.
1.2.7. Current Consumption
Access Time
The current consumption at an input voltage of +5 VDC is described in Table 2.
Table 2: IDE 4000 Input Current Consumption with +5 VDC Input Voltage
Function/Mode
Read
Current (max) mA DC
23.0
23.0
5.0
Write
Idle/Sleep
6
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
The current consumption at an input voltage of +3.3 VDC is described in Table 3.
Table 3: IDE 4000 Input Current Consumption with +3.3VDC Input Voltage
Function/Mode
Read
Current (max) mA DC
16.0
16.0
< 1
Write
Idle/Sleep
1.2.8.
Memory Capacity
Sectors) settings for the IDE 4000, capacities 128MB to 512MB (there are no changes for other
capacities).
Table 4: CHS Settings for Low-Capacity IDE 4000
Cylinder
V1.08
Heads
Sectors
Capacity (MB)
V1.09
500
V1.08
8
V1.09
16
V1.08
32
V1.09
32
128
256
512
993
998
1000
1015
16
16
32
32
1015
16
16
63
63
Table 5 describes the different densities of the IDE 4000 (unformatted, in MB).
Table 5: IDE 4000 Flash Disk Capacities
Disk Capacity (MB)
Disk Capacity (MB)
128
256
2048
2560
3072
3584
4096
5120
6144
7168
8192
384
512
640
768
1024
1280
1536
1792
7
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2.9.
Endurance
The IDE 4000 provides 2,000,000 write/erase cycles and an unlimited number of read cycles.
Performance is enhanced by the following features:
• Wear-Leveling Algorithm: This algorithm guarantees the use of all flash components at the
same level of the write/erase cycle.
• EDC/ECC (Error Detection Code/Error Correction): The enhanced Reed-Solomon
EDC/ECC extends disk endurance by detecting and then fixing flash blocks.
1.2.10. Mean Time Between Failures (MTBF)
Table 6 summarizes the MTBF prediction results for various IDE 4000 configurations. The
analysis was performed using a RAM Commander™ failure rate prediction.
Table 6: IDE 4000 MTBF
Failure Rate per
Million Hours
Product
Condition
MTBF (Hours)
IDE 4000 1GB
IDE 4000 2GB
IDE 4000 3GB
IDE 4000 4 to 8GB
Telcordia SR-332, GB, 25°C
Telcordia SR-332, GB, 25°C
Telcordia SR-332, GB, 25°C
Telcordia SR-332, GB, 25°C
2,893,495
2,188,066
1,759,180
1,470,874
0.3456
0.4570
0.5684
0.6799
A detailed MTBF report can be furnished upon request.
1.2.11. Physical Characteristics
1.2.11.1
Weight
The weight of the IDE 4000 complies with the values defined in Table 7.
Table 7: IDE 4000 Maximum Weight
Memory Capacity (MB)
2.5” Unit Weight (g)
1.8” Unit Weight (g)
8192
90
30
1.2.11.2 Dimensions
mounting configuration dimensions.
Table 8: Nominal Dimensions
Dimensions
Height
IDE 4000 2.5”
IDE 4000 1.8”
0.291 in
7.40 mm
69.85 mm
100.20 mm
0.339 in
8.6 mm
51.0 mm
76.3 mm
Width
2.750 in
3.945 in
2.008 in
3.004 in
Depth
8
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended Tightening Tourqe is 6.0 in-lb (0.675 N-m)
Recommended Tightening Tourqe is 6.0 in-lb (0.675 N-m)
Figure 2: IDE 4000 2.5” Assembly
Figure 3: IDE 4000 1.8” Assembly
Notes: 1. All dimensions are in mm [in].
2. General tolerance is ±0.25 mm [±0.01 in].
9
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2.11.3 Connector Interface
Table 9: J1 Pin Assignment
Pin Number
Signal Name
RESET-
HD7
Pin Number
Signal Name
GND
1
2
3
4
HD8
5
HD6
6
HD9
7
HD5
8
HD10
HD11
HD12
HD13
HD14
HD15
KEY
9
HD4
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
HD3
HD2
HD1
HD0
GND
N.C.
GND
HIOW-
HIOR-
IORDY
N.C.
GND
GND
CSEL
GND
INTRQ
HA1
IOCS16-
PDIAG-
HA2
HA0
CS0-
DASP-
VCC
CS1-
GND
VCC
GND
RSVD
Table 10: J2 Pin Assignment
Pin Number
Signal Name
Master/Slave
Master/Slave
Pin Number
Signal Name
Master/Slave
Master/Slave
47
49
48
50
10
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4: IDE 4000 Pin Configuration
1.3. Environmental Conditions
The IDE 4000 meets the performance requirements specified below, after exposure to
non-operating environmental conditions, or during and after exposure to operating environmental
conditions.
1.3.1.
Temperature
1.3.1.1 Operating
The IDE 4000 operates without degradation at a pressure of 1 atm over the following ambient
temperature range:
• Commercial temperature version: 0°C to +70°C : for IDE 4000 2.5” and 1.8”
• Extended temperature version: -40°C to +85°C :for IDE 4000 2.5”
The maximum temperature change rate shall not exceed 5°C per minute.
1.3.1.2 Non-Operating
The IDE 4000 commercial temperature version meets the performance requirements specified in
this document after having been tested via exposure to a nominal ambient temperature of -55°C
for not less than 3 days, and +95°C for a period of not less than 6 hours.
The maximum temperature change rate shall not exceed 5°C per minute.
11
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3.1.3 Airflow Requirements
General airflow guideline: 3-5 cu.feet/min.
1.3.2.
Altitude
The IDE 4000 sustains full operation at altitudes ranging from sea level to 80,000 feet above sea
level. It is also capable of full operation during air transportation via non-pressurized flights at
altitudes greater than 80,000 feet above sea level.
1.3.3.
Relative Humidity
The IDE 4000 withstands conditions of 8% to 95% non-condensing relative humidity (operation
and non-operation).
1.3.4.
Shock
The IDE 4000 sustains full operation after being subjected to 1000 G shock testing in the vertical
axis.
1.3.5.
Vibration
The IDE 4000 remains operational without degradation while being subjected to a 15 G vibration
condition.
1.3.6.
Storage Life and Data Retention
The IDE 4000 can be placed in non-operational storage in shipping containers or crates for a
period of up to 3 years without its capabilities being permanently affected. The IDE 4000 has a
data retention span of over 10 years.
12
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
3. INTERFACE CONNECTORS
The IDE 4000 has a 2-mm pitch interface connector located on the rear panel. It accesses the DC
power source and the IDE bus through a non-shielded 44-pin flat cable. Figure 6 provides an
example of a connector that can be used to interface with this connector, but any compatible
connectors may be used.
Figure 6: IDE 4000 Interface Connector
In order to prevent damage to the disk by connecting the cable with a 180º rotation, ensure that
the special plastic key at pin 20 mating connector is blocked, as shown in Figure 6. This key
should be ordered from the connector manufacturer.
IDE Cable
The cable length should not exceed 18 inches.
14
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
4. SUPPORTED IDE COMMANDS
The IDE 4000 supports the commands listed in Table 11.
Table 11: IDE Commands
Command Name
CHECK POWER MODE
EXECUTE DEVICE DIAGNOSTIC
FORMAT TRACK
Command Code
98h E5h
90h
50h
IDENTIFY DEVICE
Ech
IDLE
97h E3h
95h E1h
91h
IDLE IMMEDIATE
INITIALIZE DEVICE PARAMETERS
READ BUFFER
E4h
READ DMA (with retry)
READ DMA (without retry)
READ MULTIPLE
C8h
C9h
C4h
READ SECTOR(S) (with retry)
READ SECTOR(S) (without retry)
READ LONG
20h
21h
22h 23h
40h
READ VERIFY SECTOR(S) (with retry)
READ VERIFY SECTOR(S) (without retry)
RECALIBRATE
41h
10h
SEEK
70h
SET FEATURES
Efh
SET MULTIPLE MODE
SLEEP
C6h
99h E6h
96h E2h
94h E0h
E8h
STANDBY
STANDBY IMMEDIATE
WRITE BUFFER
WRITE DMA (with retry)
WRITE DMA (without retry)
WRITE MULTIPLE
CAh
CBh
C5h
WRITE SECTOR(S) (with retry)
WRITE SECTOR(S) (without retry)
WRITE LONG
30h
31h
32h 33h
15
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
5. CE AND FCC COMPATIBILITY
The IDE 4000 complies with the following CE requirements and FCC standards:
• FCC Part 15 Class B
• EN 55022 Class B, CISPR 22 Class B (MIC)
• V-3/2001.04 Class B (Japan), AS/NZS 3548 Class B (Australia/NZ)
• BSMI CNS 13438 Class B (Taiwan)
• CAN/CSA-CISPR 22-96 Class B (Canada) CFR 47 FCC Class B
• EN 55024, EN 61000 (EMC)
16
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
6. LABEL INFORMATION
The outside label contains the following information:
5
1
6
7
8
2
3
4
9
Figure 7: Outside Label
1. CE and FCC logos
2. Product name
3. Unformatted capacity value
4. M-Systems logo
5. Ordering information
6. Serial number, including date code
7. Part number
8. Declaration
9. ESD warning logo and statement
17
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
7. USING THE IDE 4000 FLASH DISK
The IDE 4000 is shipped with the following components:
• Warranty certificate indicating M-Systems’ 36-month warranty
• Four screws and one jumper, in kit no. 48-PK-001-00
If any of these items is missing, please contact your dealer.
7.1. Unpacking the Drive
Before unpacking or handling a drive, take all proper electrostatic discharge (ESD) precautions,
including personnel and equipment grounding.
Before you begin installing the IDE 4000 in your system, perform a visual inspection and follow
the recommendations below:
• If the shipping container appears to be damaged or water-stained, notify your dealer.
• Remove the disk from its shipping enclosure and inspect it for any damage that may have
occurred during shipment. If any damage is observed, notify your dealer.
• Record the disk serial number and shipment date.
• Retain the original shipping enclosure and all packing material for re-shipment.
7.2. Handling Instructions
You can prolong the life of your IDE 4000, increase its reliability, and prevent unnecessary
damage by following the instructions listed below. Failure to follow any of these instructions
may void your warranty.
• Always take all proper electrostatic discharge (ESD) precautions, including personnel and
equipment grounding.
• Always operate the flash disk within the environmental specifications.
• Always use a grounded wrist strap when handling the flash disk.
• Never switch DC power to the drive by plugging an electrically live source cable into the
drive’s power connector.
• Pay attention to the cable polarity whenever connecting the drive to the cable.
7.3. Installing the Drive in a PC
To install the IDE 4000:
1. Power off the PC and remove the cover.
18
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Connect a 44-pin ribbon cable between the IDE 4000 and the adapter. Make sure to orient
the cable so that pin 1 of the IDE 4000 is connected to pin 1 of the host adapter.
4. Mount the IDE 4000 in a free drive bay.
5. Close the PC cover and power on the PC.
The host BIOS sign-on message appears and displays a key sequence to enter the BIOS setup.
Set up the BIOS to recognize the IDE 4000.
7.4. Using the IDE 4000 in an MS-DOS-Based Platform
After installing the IDE 4000, it must be installed as a disk drive under DOS. Run the DOS
commands listed below and follow the instructions displayed for each command. For more
information regarding DOS commands, refer to your DOS manual.
• Run the DOS FDISK program to partition the IDE 4000.
• Run the DOS FORMAT command to high-level format the IDE 4000.
• If you want the IDE 4000 to be a bootable drive, run the DOS SYS command and change the
partition to active.
7.5. Troubleshooting
The problems that arise in most installations can be summarized below:
Cables:
• Homemade, short, flat ribbon cables with bad contacts or cheap cables
• Mixing round cables with flat cables.
Cable Length:
• The cable exceeds the length specified in the standard
• Cables are too long to support the transfer rate.
Device Address Conflict:
• A new device was added with an IDE setting identical to an existing device on the bus.
• Connection problems.
• A cable was connecting with reverse polarity.
19
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
7.6. How to Get Help
If you need technical assistance with the installation and configuration of your IDE 4000, please
contact your customer support representative and have the following information available:
• Product and serial number of your IDE 4000
• Description of your computer hardware (manufacturer, model, attached devices, etc.)
• Description of your IDE host adapter and associated drivers
• Description of your software (operating system, version, application software, etc.)
• A complete description of the problem
• The exact wording of any error messages
Before contacting M-Systems directly, first contact your dealer (if you did not purchase you
IDE 4000 directly from M-Systems). If your dealer cannot provide the help you need, you can
obtain technical support directly from M-Systems at one of the numbers in the list of offices on
20
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
8. WARRANTY
The warranty period of the IDE 4000 is 36 months (3 years). For details, please refer to the
warranty certificate, which is included with the IDE 4000.
21
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
9. ORDERING INFORMATION
Ordering information for the IDE 4000 2.5”: IDE-4K-25-CCCC-T
Ordering information for the IDE 4000 1.8”: IDE-4K-18-CCCC-T
Where:
CCCC: Capacity (MB)
128, 256, 384, 512, 640, 768, 1024, 1280, 1536, 1792, 2048,
2560, 3072, 3584, 4096, 5120, 6144, 7168, 8192
T:
Temperature Range Blank
Commercial: 0°C to +70°C (for 2.5” and 1.8”)
Extended: -40°C to +85°C (for 2.5” only)
Note: the IDE 4000 in a 1.8” casing is available only in commercial temperature range.
X
22
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONTACT US
USA
China
M-Systems Inc.
555 North Mathilda Avenue, Suite 220
Sunnyvale, CA 94085
Phone: +1-408-470-4440
Fax: +1-408-470-4470
M-Systems China Ltd.
Room 121-122
Bldg. 2, International Commerce & Exhibition Ctr.
Hong Hua Rd.
Futian Free Trade Zone
Shenzhen, China
Phone: +86-755-8348-5218
Fax: +86-755-8348-5418
Japan
Europe
M-Systems Japan Inc.
M-Systems Ltd.
Asahi Seimei Gotanda Bldg., 3F
5-25-16 Higashi-Gotanda
Shinagawa-ku Tokyo, 141-0022
Phone: +81-3-5423-8101
Fax: +81-3-5423-8102
7 Atir Yeda St.
Kfar Saba 44425, Israel
Tel: +972-9-764-5000
Fax: +972-3-548-8666
Taiwan
Internet
M-Systems Asia Ltd.
14 F, No. 6, Sec. 3
Minquan East Road
Taipei, Taiwan, 104
Tel: +886-2-2515-2522
Fax: +886-2-2515-2295
General Information
Sales and Technical Information
This document is for information use only and is subject to change without prior notice. M-Systems Flash Disk Pioneers Ltd. assumes no
responsibility for any errors that may appear in this document. No part of this document may be reproduced, transmitted, transcribed, stored in a
retrievable manner or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without prior written consent of M-Systems.
M-Systems products are not warranted to operate without failure. Accordingly, in any use of the Product in life support systems or other
applications where failure could cause injury or loss of life, the Product should only be incorporated in systems designed with appropriate and
sufficient redundancy or backup features.
Contact your local M-Systems sales office or distributor, or visit our website at www.m-systems.com to obtain the latest specifications before
placing your order.
© 2005 M-Systems Flash Disk Pioneers Ltd. All rights reserved.
M-Systems, DiskOnChip, DiskOnChip Millennium, DiskOnKey, DiskOnKey MyKey, FFD, Fly-By, iDiskOnChip, iDOC, mDiskOnChip,
mDOC, Mobile DiskOnChip, Smart DiskOnKey, SmartCaps, SuperMAP, TrueFFS, uDiskOnChip, uDOC, and Xkey are trademarks or
registered trademarks of M-Systems Flash Disk Pioneers, Ltd. Other product names or service marks mentioned herein may be trademarks or
registered trademarks of their respective owners and are hereby acknowledged. All specifications are subject to change without prior notice.
23
Product Specification and User Manual IDE 4000 Flash Disk
34-PS-0304-00 Rev. 2.1
Download from Www.Somanuals.com. All Manuals Search And Download.
|