M Systems Flash Disk Pioneers Computer Accessories 91 SR 005 10 7L User Manual

Installation Manual  
IM-DOC-021  
Using the DiskOnChip®  
with Linux OS  
DEC-99  
91-SR-005-10-7L REV. 2.0  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
Contents  
1
2
3
Introduction...................................................................................................................................4  
Hardware Requirements for the DiskOnChip ..........................................................................4  
Requirements for Installation of the DiskOnChip into Linux.................................................5  
3.1 Utilities Diskette Content.........................................................................................................5  
3.2 Linux Driver for DiskOnChip ...................................................................................................6  
4
5
Installing the DiskOnChip as an Additional Drive....................................................................7  
4.1 Updating the Firmware............................................................................................................7  
4.2 Integrating the TrueFFS driver into Linux................................................................................7  
Booting Linux from the DiskOnChip........................................................................................13  
5.1 Creating a Root File System.................................................................................................13  
6
7
Troubleshooting.........................................................................................................................16  
Additional Information and Tools .............................................................................................18  
Appendix I: Making a Root File System...........................................................................................19  
Appendix II: Booting from a HDD when the DiskOnChip Firmware is Active ............................22  
Appendix III: Applying a Patch Manually..........................................................................................23  
How to Contact Us.............................................................................................................................25  
91-SR-005-10-7L REV. 2.0  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
1
Introduction  
M-Systems’ DiskOnChipâ is a family of flash disks. It contains built-in firmware that provides full hard disk  
emulation and allows the DiskOnChip to operate as a boot device.  
When used under Linux, the DiskOnChip is managed by a device driver, based on M-Systems’ TrueFFSÒ  
(True Flash File System) technology. The TrueFFS driver is attached to the standard Linux file system  
[ext2].  
M-Systems provides two different TrueFFS drivers for Linux. One driver supports kernel versions 2.0.##  
and the other driver supports kernel versions 2.2.##. This Installation Manual can be used for both drivers.  
When there are differences in the installation, it will be pointed out in the text.  
This Installation Manual note is intended for system integrators designing with the DiskOnChip 2000 or  
DiskOnChip Millennium and describes how the DiskOnChip can be installed as an additional disk or as a  
boot device under Linux.  
It is assumed that the reader is familiar with the Operating System in use.  
While the hardware requirements of the DiskOnChip will be briefly discussed, the main part of this  
installation manual is related to software installation. This will include basic driver installation and boot issues.  
2
Hardware Requirements for the DiskOnChip  
Originally designed for PC environments, the DiskOnChip can also be used in different hardware  
environments. The minimum requirements are a 12-bit address bus, an 8-bit data bus, and three active low  
control signals (CE#, OE#, WR#). Following is a drawing of the DiskOnChip and its pins. For more  
detailed information of the DiskOnChip hardware environment, refer to the various DiskOnChip Datasheets  
or to the following Application Notes:  
· AP-DOC-10 “Designing with the DiskOnChip”  
· AP-DOC-30 “Designing with the DiskOnChip Millennium in a RISC Environment”  
· AP-DOC-31 “Designing with the DiskOnChip Millennium in a PC Environment”  
91-SR-005-10-7L REV. 2.0  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
1
2
NC  
5V  
30  
NC (A16)  
NC (A15)  
NC (A14)  
NC (A13)  
3
29  
28  
32  
VCC  
0.1  
16  
4
25  
23  
26  
27  
5
GND  
SA12  
SA11  
SA10  
SA9  
SA8  
SA7  
SA6  
SA5  
SA4  
SA3  
SA2  
SA1  
SA0  
A12  
A11  
A10  
A9  
A8  
A7  
DiskOnChip  
13  
14  
15  
17  
18  
19  
20  
21  
D0  
D1  
D2  
D3  
D4  
D5  
D6  
D7  
SD0  
SD1  
SD2  
SD3  
SD4  
SD5  
SD6  
SD7  
6
A6  
A5  
7
8
9
A4  
A3  
A2  
10  
11  
12  
A1  
A0  
22  
24  
31  
Active Low Chip Enable  
Active Low Output Enable  
Active Low Write  
CE  
OE  
WR  
Figure 1: DiskOnChip Pins  
3
Requirements for Installation of the DiskOnChip into Linux  
In order to prepare the DiskOnChip to boot Linux, the following software programs and tools are required:  
· Linux should be installed on your HDD. It is possible to check the kernel version by typing the command  
uname -r.  
· The Linux kernel sources should be installed in Linux (if you don’t have them, refer to kernel-HOWTO at  
If you are about to install Linux, make sure that you also install the kernel sources package and that it is  
possible to pass a full compilation of your sources.  
· A DOS boot diskette or a HDD that boots DOS.  
· M-Systems’ DiskOnChip DOS utilities diskette.  
· M-Systems’ TrueFFS driver for Linux.  
Note: The latest Disk OnChip DOS utilites can be downloaded from M-System’ website: www.m-sys.com.  
3.1 Utilities Diskette Content  
The following files are needed from the DiskOnChip DOS utilities diskette:  
91-SR-005-10-7L REV. 2.0  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
dformat  
dupdate  
docpmap  
DiskOnChip formatting utility  
Utility for updating DiskOnChip firmware  
Utility to retrieve information about the DiskOnChip  
doc121.ex  
b
DiskOnChip firmware image. “121” is the firmware version, the actual diskette might  
contain higher versions of the firmware, e.g. doc122.exb, doc123.exb, etc.  
doc2.fff  
Alternative firmware image for the DiskOnChip  
Note: The file doc2.fff can be found in the \AP012directory when using DiskOnChip DOS utilities  
version 1.21 or higher.  
3.2 Linux Driver for DiskOnChip  
The compressed file driver.tgzcontains the following files:  
/usr/src/linux/drivers/block/flash_doc/flobj.obj  
TrueFFS device driver core object file  
/usr/src/linux/drivers/block/flash_doc/fldrvlnx.c  
Source code for driver integration with  
kernel  
/usr/src/linux/drivers/block/flash_doc/makefile  
/tmp/doc-driver/lilo-patch  
TrueFFS driver’s makefile  
Patch for Lilo to make pLilo  
/tmp/doc-driver/plilo  
Linux loader, patched to use with the  
DiskOnChip  
/tmp/doc-driver/lilo.conf  
/tmp/doc-driver/boot.b  
Lilo sample configuration file  
Boot loader, udpated to use with  
DiskOnChip  
/tmp/doc-driver/copy2doc  
/tmp/doc-driver/pam.d/other  
Sample scripts, aid tool to create a root file  
system  
File meant only for Redhat & Caldera,  
defines permission access  
/tmp/doc-driver/samplefs.txt  
Sample root file system listing  
/tmp/doc-driver/doc-patch-2.0.##  
Patch for kernel sources 2.0.## (only  
attached to TrueFFS driver for kernel  
versions 2.0.##)  
/tmp/doc-driver/doc-patch-example  
Example patch for kernel sources 2.2.##  
(only attached to TrueFFS driver for kernel  
versions 2.2.##)  
Note: The included patch files are different for the two TrueFFS drivers. When using the TrueFFS driver for kernel  
versions 2.2.##, the kernel needs to patched manually and only an example patch file (/tmp/doc-driver/doc-patch-example)  
is provided. Refer to appendix III on how to manually patch your kernel.  
91-SR-005-10-7L REV. 2.0  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
4
Installing the DiskOnChip as an Additional Drive  
Before the DiskOnChip can be used as the boot disk for Linux (see Chapter 5), it first needs to be installed  
as an additional disk in the system (Linux is booted from a HDD). This chapter describes how to prepare  
the DiskOnChip and Linux to configure the DiskOnChip as an additional disk in the system. To achieve this,  
the firmware on the DiskOnChip needs to be updated (par. 4.1) and then the TrueFFS device driver needs  
to be integrated into Linux (par. 4.2). This is done as follows:  
1. Configure Linux with the required devices (par. 4.2.1 Preparing Linux for Integration).  
2. Add the TrueFFS driver to the kernel and recompile the kernel (par. 4.2.2 Adding the Driver to the  
Kernel).  
3. Boot the compiled kernel from your HDD (par. 4.2.3 Booting the Compiled Kernel from HDD).  
4. Create a Linux partition on the DiskOnChip (par. 4.2.4 Creating a Linux Partition on the  
DiskOnChip).  
5. Create a native Linux file system on the DiskOnChip (par. 4.2.5 Creating a Native Linux File System  
on the DiskOnChip).  
4.1 Updating the Firmware  
Before the DiskOnChip can be used as the boot disk or as an additional disk in Linux, it needs to be  
formatted with the alternative firmware image.  
1. Plug the DiskOnChip into its socket and boot DOS from your HDD.  
2. Format the DiskOnChip with the alternative firmware:  
dformat /win:d000 /s:doc2.fff /y  
Note: If you receive the error: “No DiskOnChip 2000 (R) was found at D000:0”, then run the DOS command docpmap /i  
to find out at which address the DiskOnChip is located.  
4.2 Integrating the TrueFFS driver into Linux  
4.2.1Preparing Linux for Integration  
To prepare Linux for integration of the driver, perform the following steps:  
Note: To perform these steps, you must be logged in as the superuser (root).  
91-SR-005-10-7L REV. 2.0  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
1. The floppy drive must be active. Verify this by typing:  
# mount  
If the /dev/fd0 doesn’t appear in the first column, type:  
# mount/dev/fd0 /mnt  
From this point, it is assumed that the diskette that contains the TrueFFS driver for Linux is mounted at  
/mnt.  
2. The kernel sources must be installed. To check this, type:  
# ls /usr/src/linux  
If this directory exists, then the kernel sources are installed. If not, refer to http://sunsite.unc.edu/LDP/ or  
type:  
zcat /usr/doc/HOWTO/Kernel-HOWTO.gz | more  
3. Unzip and untar the file driver.tgz, located on your diskette, as follows:  
# cd /tmp  
# mkdir temp  
# cd temp  
# tar -zxvf /mnt/driver.tgz  
# cp -rf . /  
# cd ..  
# rm -fr temp  
# cd /usr/src/linux/  
4. If you are installing the TrueFFS driver for kernel versions 2.0. ##, type the following command:  
# patch -p0 < /tmp/doc-driver/doc-patch-2.0.##  
This will patch the current kernel sources to include the TrueFFS driver for Linux (with ## = kernel  
version). Notice that the patch for the kernel is working only on original kernel sources, and that the patch  
is version specific. In case the utility patchis not available in your Linux environment, refer to Chapter 6  
“Troubleshooting”.  
Note: If you are installing the TrueFFS driver for kernel versions 2.2.##, the kernel sourced need to be patched manually  
(see Appendix III "Applying a patch manually"). For your reference, an example patch file is included with the driver.  
91-SR-005-10-7L REV. 2.0  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
5. Configure the kernel as follows:  
# cd /usr/src/linux  
# make menuconfig  
or  
# make config if the last command doesn’t work.  
Define your system by marking the correct devices. If you aren’t sure what the purpose of the device is,  
then leave it as it is. Make sure that you mark the DiskOnChip as “Y”es under ‘Floppy, IDE and other  
devices’. When you are finished, exit and the new configuration will be saved.  
For further details about compiling the kernel or how to apply a patch, refer to http://sunsite.unc.edu/LDP/  
or type:  
# zcat /usr/doc/HOWTO/Kernel-HOWTO.gz | more  
6. Remove the old object files:  
# make clean  
4.2.2Adding the Driver to the Kernel  
To compile the TrueFFS driver for Linux:  
1. Type the following command:  
# cd /usr/src/linux/drivers/block/flash_doc  
# make  
2. Check dependencies:  
# cd/usr/src/linux  
# make dep  
3. Compile the kernel (this may take up to 15 minutes):  
# make zImage  
If the kernel is compiled successfully, a message similar to the one below should be shown:  
Root device is (3, 3)  
Boot sector 512 bytes  
Setup is 4332 bytes  
System is 374 kB  
Sync  
91-SR-005-10-7L REV. 2.0  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
Make[1]:Leaving directory ‘/usr/src/  
linux-2.0.32/arch/i386/boot’  
If there are any compilation errors, refer to Chapter 6 “Troubleshooting”.  
4.2.3Booting the Compiled Kernel from HDD  
The new compiled kernel needs to be booted from the HDD. The following steps need to be performed:  
1. Type the following commands:  
# cp /usr/src/linux/arch/i386/boot/zImage/doc2000  
# vi /etc/lilo.conf  
2. Add the following lines at the bottom of the file (press ‘INS’ to edit the file and save and exit by typing  
<Esc>, ‘:’, ‘w’, ‘q’):  
image = /doc2000  
root = /dev/hda1  
label = doc2000  
read-only  
Note: The device /dev/hda1points to the HDD that Linux boots from. hda1is the first partition (1) on the first IDE  
hard disk (a), hdb2is the second partition (2) on the second IDE hard disk (b), etc. If it is not clear which device it is, look  
at the start of the file lilo.confand search for the line first root = ...)  
3. Make the inodes for the DiskOnChip:  
# cd /dev  
# mknod fla b 62 0  
# mknod fla1 b 62 1  
# mknod fla2 b 62 2  
# mknod fla3 b 62 3  
# mknod fla4 b 62 4  
Number 62 stands for major device number. Since it is hard coded into the driver, no other number would  
work.  
4. Run Lilo (Linux Loader) to create the map for the kernel and make sure that “doc2000” is listed (if not,  
return to the beginning of paragraph 4.2.3):  
# lilo  
5. Load the updated kernel with the TrueFFS, perform the following steps:  
6. Reboot the computer and load Linux.  
91-SR-005-10-7L REV. 2.0  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
7. When the Lilo prompt is displayed, press <Ctrl> or <Alt> or <Tab>. The screen will show :  
Lilo boot:  
8. Load the recompiled kernel:  
Lilo boot:doc2000  
4.2.4Creating a Linux Partition on the DiskOnChip  
To create a Linux partition on the DiskOnChip, all the DOS partitions on the DiskOnChip need to be  
removed and a Linux partition with the native Linux File system [ext2] needs to be created.  
1. Run the fdiskutility.  
# fdisk /dev/fla  
Note: You may create more than one primary partition. Just make sure that the boot flag of the main partition boot is active.  
Note: For further information on the fdiskutility, refer to the man pages.  
2. Display the contents of the partition table:  
Command(m for help):p  
3. Delete all existing partitions, enter each partition number for deletion:  
Command(m for help):d  
4. Create a new Linux native partition:  
Command(m for help): n  
Command actione extended  
p primary partition (1-4)p  
Partition number (1-4): 1  
First cylinder (1-XXX): 1  
Last cylinder or +size or +sizeM or +sizeK ([1] XXX):XXX  
5. Change the type of the partition to Linux native:  
Command (m for help): t  
Partition number (1-4): 1  
Hex code (type L to list codes): 83  
6. Make the partition bootable:  
Command (m for help): a  
Partition number (1-4): 1  
91-SR-005-10-7L REV. 2.0  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
7. Recheck the partition table:  
Command (m for help): p  
Disk /dev/fla: 16 heads, 9 sectors, 1002  
Cylinder units = cylinders of 144 * 512 bytes  
Device boot begin Start End Blocks Id System  
/dev/fla1 *  
1
1 1002 72139+ 83 Linux native  
8. Save the new partition table (disregard any fdiskwarnings):  
Command (m for help): w  
9. Reboot the machine to let the new partition table load into memory and load Linux again with the new  
compiled kernel. If there is more than one partition, this step is vital.  
4.2.5Creating a Native Linux File System on the DiskOnChip  
To initialize the file system on the newly created Linux partition on the DiskOnChip  
1. Type the following command:  
# mke2fs /dev/fla1  
Note: When a small capacity DiskOnChip is used (4MB or smaller), more space for inodes needs to be allocated. Type the  
following command:  
# mke2fs -i 2048 /dev/fla1  
2. Mount the file system to a directory:  
# mkdir /diskonchip  
# mount /dev/fla1 /diskonchip  
From now on, it is possible to use the DiskOnChip as an additional disk in your system.  
Note: If you have created more than one partition, repeat the last step for each partition (dev/fla1, /dev/fla2,  
etc.).  
91-SR-005-10-7L REV. 2.0  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
5
Booting Linux from the DiskOnChip  
Being able to boot Linux from the DiskOnChip makes it possible to use the DiskOnChip as the only disk in  
the system, holding the OS itself in addition to all other applications and files.  
In order to make a block device bootable on Linux, the kernel and the Lilo program should be copied to the  
block device and a root file system needs to be created. Creating a root file system on Linux is necessary, as  
from this root file system the kernel is activating several programs, such as:  
Initialize all processes  
Init  
Activate swapping  
Swapo  
n
Mount the root and proc  
filesystems  
Mount  
Shell  
Sh  
For further details refer to http://sunsite.unc.edu/LDP/ or type:  
#zcat /usr/doc/HOWTO/Bootdisk-HOWTO.gz | more  
Warning: Notice that the DiskOnChip firmware (i.e. doc121.exb) collides with Lilo. This means that it  
is not possible to load Linux from the HDD after the original firmware is restored (see par. 5.1.4). This  
doesn’t mean that the HDD is non-functional. It only means that the alternate firmware (doc2.fff) needs  
to be reloaded (see par. 4.1).  
If it is required to boot Linux from both the HDD and the DiskOnChip, it is necessary to use both pLilo and  
boot.b (provided with the TrueFFS driver). For further details, refer to Appendix II.  
5.1 Creating a Root File System  
5.1.1Introduction  
This section is based on Bootdisk-HOWTO and other experiments. Since each distribution has a different  
file location and different installations, it is possible that you won’t succeed in booting Linux the first time  
from the DiskOnChip. When you receive errors, follow each error and try to fix things, but reload Linux  
from the HDD and remount the DiskOnChip each time.  
Note: There are several programs that create a root file system. It is not possible to say that any of them is complete right  
now, but they are worth trying. The following program is recommended:  
Yard: Yard creates rescue disks (also called boot disks) for Linux. A rescue disk usually contains utilities for diagnosing  
and manipulating hard disks and file systems. It is used when it is not possible (or if it is not required) to boot from your  
Note: For a sample root file system, refer to the file /tmp/doc-driver/samplefs.txt which is part of the  
compressed file driver.tgz.  
91-SR-005-10-7L REV. 2.0  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
5.1.2Overview  
A root file system must contain everything that is needed to support a full Linux system. To achieve this, the  
disk must include the minimum requirements for a Linux system:  
· Basic file system structure  
· Minimum set of directories: /dev, /proc, /bin, /etc, /lib, /usr, /tmp  
· Basic set of commands: sh, ls, cp, mv, etc.  
· Minimum set of config files: rc, inittab, fstab, etc.  
· Devices: /dev/hd*, /dev/tty*, /dev/fd0, etc.  
· Runtime libraries to provide basic functions used by utilities  
5.1.3Populating the File System  
From this point on, it is assumed that the DiskOnChip is mounted to the /diskonchipdirectory.  
The sample script copy2docthat is provided with the driver is located in directory /tmp/doc-  
driver. This sample script is created for RedHat 5, SuSE 5.2 and Caldera and is customized for RedHat  
5. It might be necessary to change the script according to your distribution. Files that are specific to a  
distribution can be found in the script with the distribution name written after it. To exclude a file, make sure  
the ‘#’ mark is present at the beginning of the line. To include a file, make sure the ‘#’ mark is removed.  
The sample script only copies the basic files that are needed for booting. For any other operation, it is  
necessary to add more files.  
To create a root file system based on the sample script copy2doc, perform the following steps:  
1. Go to the /diskonchipdirectory:  
# cd /diskonchip  
2. If necessary, customize the sample script (for other distributions):  
# vi /tmp/doc-driver/copy2doc  
3. Run the script:  
# sh /tmp/doc-driver/copy2doc  
4. Create the list of files to be mounted:  
# vi /diskonchip/etc/fstab  
5. Press <INS> to start editing and insert the following lines:  
/dev/fla1 /  
/proc  
ext2 defaults 1 1  
/proc proc defaults 0 0  
91-SR-005-10-7L REV. 2.0  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
Press <ESC>, ‘:’, ‘w’, ‘q’ to save the file. It is possible to  
add more devices here (for more information, refer to the man  
pages).  
6. For RedHat and Caldera it is also necessary to copy the configuration file for the pam library (responsible  
for making authentic users):  
# cp /tmp/doc-driver/pam.d/other  
/diskonchip/etc/pam.d/other  
Note: Appendix I explains how to create your own root file system manually. Although this is more complicated than using  
the above mentioned sample script, it is highly recommended.  
All modules should be placed in /lib/modules/. It is necessary to include at least the programs  
insmod, rmmodand lsmod. If it is required to load the modules automatically, then also include  
modprobe, depmodand swapout. When using kerneld, include it along with  
/etc/conf.modules.  
Some system programs, such as login, complain when the file /var/run/utmpand the directory  
/var/logdo not exist. To solve this, type the following commands:  
# mkdir -p /diskonchip/var/{log,run}  
# touch /diskonchip/var/run/utmp  
After all the needed libraries and programs are set up, run ldconfigto remake  
/etc/ld.so.cacheon the root file system. The cache tells the loader where to find the libraries. To  
remake ld.so.cache, type the following command:  
# cd /diskonchip  
# chroot /diskonchip /sbin/ldconfig  
The command chrootis necessary, because ldconfigalways remakes the cache for the root file  
system.  
5.1.4Copying the Kernel, Updating the Boot Sector and Rebooting  
To copy the kernel and to update the boot loader files.  
1. Type the following commands:  
# mkdir /diskonchip/boot  
# cp /usr/src/linux/arch/i386/boot/zImage  
/diskonchip/boot/doc2000  
# rdev /diskonchip/boot/doc2000 /dev/fla1  
# cp /tmp/doc-driver/plilo /diskonchip/sbin  
91-SR-005-10-7L REV. 2.0  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
# cp /tmp/doc-driver/boot.b /diskonchip/boot  
# cp /tmp/doc-driver/lilo.conf /diskonchip/etc  
# /diskonchip/sbin/plilo -C /diskonchip/etc/lilo.conf -i  
/diskonchip/boot/boot.b -m /diskonchip/boot/map  
2. Verify that after the last command, the device doc2000is listed on the screen.  
3. If it is required to load other partitions, then the file /diskonchip/etc/lilo.confshould be  
edited.  
Note: pLilo is the patched Lilo, which ensures that the DiskOnChip firmware will not collide with the Linux bootloader.  
The final steps in the process of making the DiskOnChip bootable for Linux are as follows:  
1. Unmount the DiskOnChip:  
# cd /  
# unmount /dev/fla1  
2. Reboot and load DOS, and reinstall the original firmware:  
A:> dupdate /win:D000 /s:doc121.exb  
sys.com)  
3. Reboot the machine and disable the HDD in the BIOS setup or make the DiskOnChip the first boot  
device in the system by using the following command:  
A:> dupdate /win:D000 /s:DOC110.EXB /FIRST  
4. Linux will now boot from the DiskOnChip.  
6
Troubleshooting  
Adding more programs to Linux root file system  
If the DiskOnChip boots Linux without a problem and it is required to add more programs to the Linux root  
file system, then mount the HDD and copy the required files.  
DiskOnChip does not boot Linux  
There are several errors that you can encounter during boot:  
· If the DiskOnChip does not boot at all, follow all the instructions from the start of this Installation Manual.  
In addition, remember to update the original firmware of the DiskOnChip (i.e. doc121.exb) with the  
alternate firmware (doc2.fff) in order to boot Linux from your HDD.  
· If the kernel boots, but it gets stuck on:  
91-SR-005-10-7L REV. 2.0  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
VFS: Unable to mount -.  
Most likely, you forgot to do:  
# rdev /diskonchip/boot/doc2000 /dev/fla1  
· If the DiskOnChip boots and the kernel is loading, but it gets stuck after:  
VFS: Mounted root (ext 2 filesystem) readonly.  
Most likely, the initprogram or some if its configuration files weren’t copied.  
Cannot log in  
If you cannot login when booting Linux from the DiskOnChip, make sure that:  
· Your default shell is installed.  
· The pam libraries were placed as explained in par. 5.1.3 (only for RedHat and Caldera).  
Refer to Appendix II in order to solve this problem.  
Kernel does not compile correctly or patch utility is not available  
If the kernel does not compile correctly, and the problem is not caused by the TrueFFS driver, refer to  
#zcat /usr/doc/HOWTO/Kernel-HOWTO.gz | more  
Kernel is too big  
When you run pLilo and you receive the error ‘Kernel xxx is too big’, recompile the kernel with the  
bzImageoption (In step 0, use make bzImageinstead of make zImage).  
For further information, refer to http://sunsite.unc.edu/LDP/ or type:  
#zcat /usr/doc/HOWTO/Kernel-HOWTO.gz | more  
91-SR-005-10-7L REV. 2.0  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
7
Additional Information and Tools  
Additional information about the DiskOnChip, including Application Notes, can be found at http://www.m-  
sys.com.  
Additional tools and documents are listed in the following table:  
Document/Tool  
Description  
AP-DOC-10  
Designing with the DiskOnChip 2000  
AP-DOC-15  
Obtaining DiskOnChip 2000 Information  
Designing with the DiskOnChip Millennium in a RISC Environment  
Designing with the DiskOnChip Millennium in a PC Environment  
DiskOnChip 2000 Data Sheet  
AP-DOC-30  
AP-DOC-31  
DiskOnChip 2000 Data Sheet  
DiskOnChip Millennium Data Sheet  
DiskOnChip Utilities  
DiskOnChip DIP EVB  
DiskOnChip2000-PIK  
DiskOnChip-GANG  
DiskOnChip Millennium Data Sheet  
DiskOnChip Utilities User Manual  
DiskOnChip Evaluation Board  
DiskOnChip DIP Programmer and Integrators Kit  
1+8 DIP Socket Gang Programmer  
91-SR-005-10-7L REV. 2.0  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
Appendix I: Making a Root File System  
To create your own root file system, perform the following steps:  
1. Make the following directories:  
# cd /diskonchip  
# mkdir bin dev etc lib mnt proc sbin tmp usr var  
2. Create devices in the /devdirectory. You can either do this manually or just copy the /devdirectory  
from the HDD. If you wish to save space, it is possible to remove non-required devices (i.e. if you don’t  
have a SCSI drive, then remove all the sd* devices).  
# cp -dpR /dev /diskonchip  
This command copies many unnecessary inodes to the DiskOnChip. Removing them causes no problem,  
as long as you make sure that the ones listed in the sample file system are present.  
3. Copy and configure the files in the /etcdirectory:  
# cp -dr /etc/rc.d /diskonchip/etc (for RedHat)  
or  
# cp -dr /sbin/init.d /diskonchip/sbin (for SuSE)  
# cp -d /etc/inittab /diskonchip/etc  
4. Copy the password file and make sure that each user has its default shell installed:  
# cp /etc/passwd /diskonchip/etc  
# cp /etc/shadow /diskonchip/etc (it is possible that you do not have this)  
# cp /etc/group /diskonchip/etc  
5. Create the file /etc/fsstabthat contains the list of files to be mounted:  
# vi /diskonchip/etc/fstab  
6. Press <INS> to start editing and insert the following lines:  
/dev/fla1 /  
/proc  
ext2  
defaults 1 1  
/proc proc  
defaults 0 0  
Press <ESC>, ‘:’, ‘w’ and ‘q’ to save the file.  
Note: It is possible to add more devices here. For more information, refer to the man pages.  
7. There are several programs that need to be copied to have a functional environment. Other programs are  
not as important, although it would be rather difficult to work without them. All other programs that are  
91-SR-005-10-7L REV. 2.0  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
not listed below are considered optional. Copy these programs to the directories /binor /sbinas  
follows:  
# cp /bin/{program_name}  
/diskonchip/bin/{program_name}  
/bin directory:  
cat  
echo  
hostname  
kill  
mount  
mv  
chmod  
chown  
cp  
ps  
Ln  
rm  
cut  
login  
Ls  
rmdir  
sh  
dd  
df  
mkdir  
mke2fs  
mknod  
more  
su  
dircolors  
du  
sync  
umount  
uname  
e2fsck  
/sbin directory:  
halt  
Shutdown  
init  
Swapoff  
Swapon  
Telinit  
ldconfig  
mingetty  
mkswap  
reboot  
rdev  
Update  
runlevel  
The file name of mingettyvaries with the distribution, i.e. RedHat and SuSE use mingetty,  
Slackware uses agetty. To find out what the name of this file in your distribution is, perform a grep on  
“getty”:  
# grep getty /etc/inittab  
8. The /libdirectory contains all the shared libraries and loaders. Only the appropriate libraries need to  
be copied to the /libdirectory. To check which libraries are needed, type the following command for  
each file in these two directories:  
# ldd /sbin/{filename}  
or  
# ldd /bin/{filename}  
91-SR-005-10-7L REV. 2.0  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
For example:  
# ldd /sbin/mke2fs  
libext2fs.so.2 /lib/libext2fs.so.2  
libcom_err.so.2 /lib/libcom_err.so.2  
libuuid.so.1 lib/libuuid.so.1  
libc.so.5 /lib/libc.so.5  
This will show which libraries are needed for the program mke2fs. In this example, it is necessary to copy  
the following four libraries:  
# cp /lib/ext2fs.so.2 /diskonchip/lib  
# cp /lib/libcom_err.so.2 /diskonchip/lib  
# cp /lib/libuuid.so.1 /diskonchip/lib  
# cp /lib/libc.so.5 /diskonchip/lib  
If you have a long list of files to be copied, it is also possible to run the following command:  
# ldd /bin/* > lib_list  
# more lib_list  
Copy the library loaders as follows:  
# cp lib/ld.so /diskonchip/lib  
(a.out loader)  
(elf loader)  
# cp /lib/ld_linux.so /diskonchip/lib  
It is possible to use objcopyto reduce the size of the libraries. For example:  
# objcopy -strip-debug /diskonchip/lib/lib.so.5  
91-SR-005-10-7L REV. 2.0  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
Appendix II: Booting from a HDD when the DiskOnChip Firmware  
is Active  
Since Lilo and the DiskOnChip firmware (i.e. doc121.exb)share the same area in RAM, the system  
will hang during boot when using an unpatched Lilo. Updating Lilo solves this problem. The existing boot  
loader needs to be updated as follows:  
# /tmp/doc-driver/plilo -i /tmp/doc-driver/boot.b  
This command uses the patched Lilo supplied by the TrueFFS driver and patched boot.b, and your  
default /etc/lilo.conf. Make sure that you run this command in the Linux that booted from the  
HDD.  
pLilo is actually forcing you to use smaller kernels because it allocates part of the physical memory to the  
driver. Therefore, big kernels (around 470 KB) will have a problem with pLilo (pLilo will stop with an error  
‘Kernel xxx is too big’). There are two solutions to this problem:  
1. Compile the kernel with the bzImage option (‘make bzImage’). Refer to  
/usr/doc/HOWTO/Kernel-HOWTO.gzfor more information.  
2. Comment out all big kernels from lilo.conf(only during the installation procedure).  
M-Systems provides a patch file to Lilo sources to make pLilo. To activate the patch, you must have the  
Lilo sources available on your system. After you verify that the sources are available, type the following  
command:  
# patch -p0 < lilo-patch  
You now have pLilo sources.  
91-SR-005-10-7L REV. 2.0  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
Appendix III: Applying a Patch Manually  
There are two ways to integrate the TrueFFS driver into the kernel: manually or with a patch utility.  
The TrueFFS driver for kernel versions 2.0.## contains patch files for kernel versions 2.0.29-2.0.35  
(/tmp/doc-driver/doc-patch-2.0.##). See paragraph 4.2.1 for detailed information on  
how to patch your kernel with these patch files.  
When using the TrueFFS driver for kernel versions 2.2.##, the kernel needs to be patched manually. For  
your reference, the driver contains an example patch file (/tmp/doc-driver/doc-patch-  
example). This appendix explains how to patch the kernel manually.  
To patch your kernel manually, go to your local kernel sources:  
# cd /usr/src/linux  
There are 5 files that you will need to patch:  
/usr/src/linux/include/linux/blk.h  
/usr/src/linux/include/linux/major.h  
/usr/src/linux/drivers/block/Makefile  
/usr/src/linux/drivers/block/Config.in  
/usr/src/linux/drivers/block/ll_rw_blk.c  
Review the example patch file (/tmp/doc-driver/doc-patch-example) provided with the  
TrueFFS driver (driver.tgz). The file will look something like this.  
--- include/linux/major.h  
Tue Aug 12 23:57:23 1997  
+++ /tmp/package/usr/src/linux/include/linux/major.h Mon Aug  
17 14:05:19 1998  
@@ -69,6 +69,8 @@  
#define APBLOCK_MAJOR 60 /* AP1000 Block device */  
#define DDV_MAJOR  
61 /* AP1000 DDV block device */  
+#define IGEL_FLASH_MAJOR 62 /* [email protected] 2.6.98 */  
+
#define SPECIALIX_NORMAL_MAJOR 75  
#define SPECIALIX_CALLOUT_MAJOR 76  
Each of the above mentioned files needs to be edited to create the correct patch for your kernel.  
91-SR-005-10-7L REV. 2.0  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
In the above example, the file /usr/src/linux/include/linux/major.his patched. The  
two lines that start with the ‘+’ mark are added to the current source code, and the lines that start with the ‘-  
‘ mark are removed from the source code. Repeat this process for all five of the above-mentioned files.  
91-SR-005-10-7L REV. 2.0  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the DiskOnChip with Linux OS  
How to Contact Us  
Internet:  
info@m-sys.com  
E-mail:  
USA Office:  
Japan Office:  
M-Systems Inc.  
M-Systems Japan Inc.  
8371 Central Ave, Suite A  
Newark CA 94560, U.S.A  
Phone: 1-510-494-2090  
Fax: 1-510-494-5545  
1-11-15 Higashi Gotonda Shinagawa-ku  
Tokyo, 141-0022 Japan  
Phone: 03-3445-9042  
Fax: 03-3445-9045  
Taiwan Office:  
U.K. Office:  
M-System Asia Ltd.  
M-Systems UK Ltd.  
11F-2, No. 81,Sec.2, Chang Teh Rd. PO Box 20  
Taipei, Taiwan, R.O.C.  
Phone: 886-2-2550-1741  
Fax: 886-2-2550-1745  
Chalgrove SPDO  
OX44 7YP  
Phone: 44 (0) 1865 891 123  
Fax: 44 (0) 1865 891 391  
Israel Office:  
M-Systems Ltd.  
Atidim Industrial Park P.O.B 58036  
Tel Aviv 61580, Israel  
Phone: 972-3-647-7776  
Fax: 972-3-647-6668  
M-Systems assumes no responsibility for the use of the material described in this document. Information  
contained herein supersedes previously published specifications on this device from M-Systems. M-Systems  
reserves the right to change this document without notice.  
91-SR-005-10-7L REV. 2.0  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Land Pride Lawn Mower FM3072 User Manual
Lenovo Personal Computer M92z User Manual
Lexmark All in One Printer 279 User Manual
LST Smoke Alarm GI 55000 217 User Manual
Marantz Car Amplifier PM 11S3 User Manual
Maytag Washer Dryer 6 2708140 0498 User Manual
Maytag Washer W10550277A User Manual
Mercedes Benz Automobile 2011 E350 4MATIC Wagon User Manual
Metabo Welder SRT 17 4 User Manual
Midland Radio Two Way Radio 75 785 User Manual