M-Audio Ozone
version: MA-Ozone_052803
User’s Guide
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
M-Audio Ozone Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
M-Audio Ozone Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Guide to Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
M-Audio Ozone Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Top Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
M-Audio Ozone Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Driver Installation for Windows . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Windows XP: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Windows 2000: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Windows ME: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Windows 98SE: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
M-Audio Ozone and the Windows Sound System . . . . . . . . . .23
Macintosh Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
OMS Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
M-Audio Ozone Driver Installation . . . . . . . . . . . . . . . . . . . . .24
OMS Configuration (Mac OS9 only) . . . . . . . . . . . . . . . . . . . .25
M-Audio Ozone and the Mac OS 9 Sound Manager . . . . . . . .27
M-Audio Ozone and Mac OS X . . . . . . . . . . . . . . . . . . . . . . . .27
The M-Audio Ozone Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . .28
Application Software Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
M-Audio Ozone Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . .31
M-Audio Ozone Audio Setup and Control . . . . . . . . . . . . . . . . . . . . .31
Using the Mic and Instrument Inputs . . . . . . . . . . . . . . . . . . . . . .33
Setting Input Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Phantom Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Using the Aux Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Using Direct Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
M-Audio Ozone MIDI Setup and Control . . . . . . . . . . . . . . . . . . . . . .37
MIDI Functions In Standalone Mode . . . . . . . . . . . . . . . . . . . .39
Utilizing the Programming Assignment Keys . . . . . . . . . . . . . . .39
Technical Support & Contact Information . . . . . . . . . . . . . . . . . . . . . .44
M-Audio Ozone Warranty Information . . . . . . . . . . . . . . . . . . . . . . . .45
M-Audio Ozone Technical Specifications . . . . . . . . . . . . . . . . . . . . . . .46
Appendix A - MIDI Controller Information . . . . . . . . . . . . . . . . . . . .47
Appendix B - M-Audio Ozone Block Diagram . . . . . . . . . . . . . . . . . .48
Download from Www.Somanuals.com. All Manuals Search And Download.
addition of eight programmable rotary knobs) allow it to send virtually any
type of MIDI controller information.Additionally, the M-Audio Ozone can
operate as a “standalone” MIDI controller, independent of the computer.
The rear panel MIDI port marked “Keyboard” is used for this purpose.
Within the M-Audio Ozone is a USB MIDI interface. Simply install the
included drivers, plug the M-Audio Ozone into your computer’s USB port,
and enable the MIDI interface within your music software. An additional
MIDI output port, labeled “USB,” allows you to connect a MIDI sound
module or drum machine so you can send MIDI messages directly from
you computer to your sound modules.
In addition to its MIDI controller features,the M-Audio Ozone is a powerful
audio interface.The Mic and Instrument inputs allow you to record vocals,
guitars or anything else into your audio program or soft-sampler.A stereo
Aux Input allows you to monitor or record stereo sources, while a pair of
line outputs and a headphone out are perfect for monitoring playback of
loops, soft synths, and all of your audio and MIDI tracks.
On a PC:You must be running Windows 98 SE or higher to properly use
the M-Audio Ozone. Also, your motherboard must support USB or you
will need to install a PCI to USB host adapter to provide the USB ports.
It is possible for a motherboard to support USB and yet not have the
physical port connectors installed. A simple USB back panel extender can
be purchased at a computer supply store and can be installed easily to
provide USB port connectors.
On a Mac:Your Mac must support USB with built-in native ports present.
A Mac OS that supports USB will also be required. We recommend OS
9.2.2 or higher.We cannot guarantee optimum performance of the device
when using non-Apple USB ports.
IMPORTANT: For MacOS 9, an OMS MIDI driver is provided. You MUST
have a sequencer program that supports OMS, and have OMS (also
included) properly installed in order to use the M-Audio Ozone.
What’s in the Box
Included in the M-Audio Ozone package, you should find:
•
•
•
•
•
M-Audio Ozone USB Audio/MIDI Mobile Workstation
One (1) standard USB cable
PC and Mac driver disk
Owner’s manual and warranty card
Power Adaptor
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to Getting Started
Here is an outline of the steps needed to begin using your M-Audio Ozone
on either a Mac or a PC:
1. Install the Driver (see “Software Installation”).
2. Attach the M-Audio Ozone to your computer (see“Hardware Installation”).
3. Connect your sound module to the M-Audio Ozone (see “M-Audio
Ozone MIDI Setup”).
4. Connect the audio inputs and outputs to your mixer or monitor
system (see “M-Audio Ozone Audio Setup”).
5. Configure the M-Audio Ozone in your application software (see“Using
the M-Audio Ozone in your Application Software”).
M-Audio Ozone Panel Features
Top Panel
1. Pitch Bend Wheel: The Pitch Bend Wheel sends out MIDI messages
used for raising or lowering the pitch of a voice during performance,
starting from and always returning to a center“detent” point.The range
of pitch values depends on the sound generator (sound card/module or
soft synth) being used. Please refer to the manual of your particular
device for information on how to change the pitch bend range.To bend
the pitch up, move the wheel away from you.To bend the pitch down,
move the wheel towards you.
2. Modulation Wheel: It is very common to use the Modulation Wheel to
change the intensity of effects, such as Vibrato (pitch change),Tremolo
(change in volume), and Modulation (change in tone).The Modulation
Wheel produces a vibrato effect shortly after the sound is generated,
and is most effective for solo instruments such as saxophone, strings,
and oboe. Similar to the pitch wheel, the actual effect and range of that
effect will be set from within your MIDI sound module.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Data Entry Slider:This slide controller allows you to adjust the value of
parameters such as Volume, Velocity, Aftertouch, and virtually any
assignable MIDI control parameter directly from your keyboard.Making
settings with the data slider is covered in the “Utilizing the
Programming Keys” section of this manual.
4. MIDI/SELECT Button: Use this button to select different MIDI
commands using certain keys from your keyboard.Activation of this key
is indicated by a lit LED on the MIDI/Select Button. When
MIDI/SELECT is activated, the keyboard becomes a set of function keys
for setting MIDI parameter commands.
5. Octave Up & Down / Preset buttons: Pressing these buttons during
normal use will allow you to select the octave orientation of the
M-Audio Ozone’s keyboard. Following a pressing of the MIDI/SELECT
button, they alternately allow you to select the preset-bank setting
(P1-P5) of the M-Audio Ozone’s keyboard. Pressing the MIDI/SELECT
button again, after a preset-bank selection, will return these buttons to
their normal octave-select function.
6. Rotary Controller Knobs:These eight programmable rotary knobs can
be used to send any MIDI controller data on any MIDI channel.This is
perfect for use with hardware and software synthesizers, for
automating software mixers, or for controlling any devices that will
respond to MIDI commands. In the “Programming Assignment Keys”
section, the “Set CNTRL Key” instructions will show you how to
program this special feature.
7. Mic/Inst. Gain:These knobs control the preamp gain of the Mic In (Ch
1) and Instrument In (Ch 2).This level is sent to the USB output for
computer recording, and also to the M-Audio Ozone Output 1 & 2
when the Direct Monitor level controls are used.
8. Signal and Clip Indicators:These indicators show the output level of the signal
coming from the Mic and Instrument Ins. For more information on setting
these controls, see the section of this manual titled,“Setting Input Gain.”
9. Direct Monitor Level Knobs:These knobs set the monitor level of the Mic
In (Ch 1) and Instrument In (Ch 2) preamp signals before they are sent to
the computer.These listening levels can then be heard at Outputs 1 & 2,
and also at the Headphone Out.When the Aux Input “Record/Monitor”
switch is set to Record, these Direct Monitor Level controls then control
the monitor level for the Aux Input signal. For more information, see the
section of this manual titled,“Using Direct Monitor.”
10. Headphone Level:This control sets the level of the audio going to the
headphone output.
11. Phantom Power Indicator:This light indicates that 48V phantom power
is being sent to the Mic In (Ch 1). Phantom Power is turned on and off
by the Phantom Power switch on the M-Audio Ozone’s rear panel.
12. Key Programming Assignments: After pressing the MIDI/SELECT
Button, the keys on the M-Audio Ozone become function keys that
allow you to assign particular MIDI parameters as well as Program
Change and MIDI Channel selections using the numbered key group.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
1. Power Switch: The Power Switch turns on the M-Audio Ozone. You
probably figured that one out for yourself.
2. Power Jack:This jack is used to connect the keyboard to the supplied
9VAC 1000mA “wall-wart” type power supply.
3. USB Port: This USB connector jack is used to connect the M-Audio
Ozone to the computer’s USB port using a standard USB cable (included).
4. MIDI Out Jack, USB:This standard MIDI jack receives its source from the
computer when software’s set to M-Audio Ozone MIDI Out - & is used to
send MIDI messages to other MIDI instruments (such as a sound module).
5. MIDI Out Jack, Keyboard:This standard MIDI jack is a direct MIDI out
from the keyboard in “standalone” mode (independent of the
computer), and is used to send MIDI messages to another MIDI
instrument (such as sound module).
6. Sustain Jack:This jack allows you to connect an optional footswitch to
the keyboard. When the footswitch is depressed, MIDI controller
“pedal sustain” information is sent from the M-Audio Ozone, while
notes played on the keyboard will continuously sound as long as the
footswitch is held.
7. Headphone Out: This jack is a 1/4” TRS stereo headphone output
which plays the same signal as the main outputs. Headphone Out level
is controlled by the Headphone Level control.
8. Outputs 1 and 2: These are the main stereo audio outputs of the
M-Audio Ozone. This signal includes the stereo output from the
computer (via the USB cable), the Aux Input (when in Monitor mode),
and the Direct Monitor signals all mixed together.
9. Aux Input Monitor/Record switch:When this switch is set to Monitor,
theAux Inputs are sent directly to the M-Audio Ozone’s Outputs 1 and
2, while Mic In (Channel 1) and Instrument In (Channel 2) are being
sent to the computer and also to the Direct Monitor circuitry.When
this switch is set to“Record,” the Mic In (Channel 1) and Instrument In
(Channel 2) are switched off (defeated), and the Aux Inputs are passed
to your computer and to the Direct Monitor circuitry.
10. Aux Input:This is a stereo 1/4” TRS jack for the two (L/R) Aux Inputs.
The Monitor/Record mode switch will determine its signal path.
11. Instrument In (Channel 2): This is a 1/4” TRS Balanced input for
instrument or line level signals. The Instrument In’s preamp gain is
controlled by the top panel “Inst Gain” control. This Channel is
defeated if the Aux Input is plugged in, and the Monitor/Record button
is pressed to the “Record” position.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Mic In (Channel 1): This is an XLR Balanced preamp input for
microphones. Mic In preamp gain is controlled by the top panel “Mic
Gain” control.This input also gets defeated if the Aux Input is plugged
in, and the Monitor/Record button is pressed to the“Record” position.
13. Direct Monitor Stereo/Mono Switch:When this switch is set to Stereo,
Channel 1 goes to the left output (Output 1) and Channel 2 goes to
the right output (Output 2)—as in a stereo signal panned hard left and
hard right. When this switch is set to Mono, both input channels are
passed to both output channels in Mono, or panned to the center.This
switch will not affect the signal that is being recorded, but only the
signal you are monitoring.
14. Phantom Power Switch:When this switch is pressed to the“in” position,
the front panel Phantom Power indicator will light and 48V will be sent
to the Mic In (Channel 1) to power a condenser microphone.
M-Audio Ozone Driver Installation
Your computer communicates with devices contained within the M-Audio
Ozone, the audio and MIDI interfaces for example, via software files known
as “drivers.” This driver software is a special, dedicated program that makes
the audio or MIDI interface accessible to an application program. On the
included driver disk, M-Audio supplies the audio and MIDI drivers that
enable you to use M-Audio Ozone with Windows, Mac OS9 or Mac OSX.
These M-Audio Ozone drivers are supplied on the dual format CD included.
Driver Installation for Windows
The drivers for the M-Audio Ozone USB interface requireWindows 98SE
or higher. Please make sure that Windows 98SE, ME, 2000 or XP is
installed on your system, and that your USB port is enabled. Check your
computer manual for more information.
To verify yourWindows installation after you have carefully followed these
instructions, you may check your system’s“Device Manager,” located in the
Control Panel under “System” (in Windows 2000 or XP, also click the
“Hardware” tab after clicking “Device Manager”). If you look in the Device
Manager, you will find components for the M-Audio Ozone driver in two
sections; once under the “Universal Serial Bus” controller group, and also
under the “Sound, video, & game controllers” group, where drivers are
displayed as follows:
Windows 2000 and XP show two M-Audio Ozone drivers under Sound,
video, game controllers—“Ozone” and “Ozone MIDI.”
Windows Me and Windows 98SE show three M-Audio Ozone drivers
under Sound, video and game controllers—“Ozone,” “Ozone MIDI” and
“Ozone MIDI (VxD).”
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows XP:
1. The M-Audio Driver CD should be inserted into the computer's CD-ROM
drive. In this example the CD-ROM drive is letter "D." (The letter of your
CD-ROM drive may be different, and you should change it accordingly.)
2. Now navigate to your CD-ROM drive. Browse the the Ozone Folder
and double-click the EXE driver.
3. The first window reminds you to verify that the M-Audio Ozone is
disconnected from the USB bus before continuing, and that you have
closed all other Windows applications.Then click “Next” to continue.
4. A“Digital Signature Not Found”Window will appear.As this is a relatively
new product, it has does not have an official Windows Digital Signature
yet. Rest assured, our USB drivers are of the highest quality and will not
cause problems in your system. Click “Continue Anyway” to continue.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Another “Digital Signature Not Found” Window will appear. Click
“Continue Anyway” to continue.
6. Another “Digital Signature Not Found” Window will appear. Click
“Continue Anyway” to continue.
7. An M-Audio Setup Window will appear next. Make sure both the
“Enable Digital CD” and “Enable DMA Transfer Mode” boxes are
checked, then click “Next.”
10
Download from Www.Somanuals.com. All Manuals Search And Download.
8. An M-Audio Setup Window will appear to confirm a successful setup.
Click “Next” to complete installation of the M-Audio Ozone.
9. Windows will prompt you to restart the computer. Make sure that“Yes,
restart my computer now,” is checked and then click“Finish” to restart.
10. When you are completely restarted, please connect the USB cable from
your M-Audio Ozone to your computer. Now power up the device by
pressing the power button on the back of the M-Audio Ozone.
11. The“Found New HardwareWizard” will appear.Click“Next” to continue.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Another Windows Logo Testing window will appear. Click “Continue
Anyway” to continue.
13. The next window informs you that the wizard has finished installing the
software. Press “Finish” to continue.
14. Another Windows Logo Testing window will appear. Click “Continue
Anyway” to continue.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
15. The “Found New Hardware Wizard” will again appear. Click “Next”
to continue.
16. Another Windows Logo Testing window will appear. Click “Continue
Anyway” to continue.
17. The next window informs you that theWizard has finished installing the
software. Press “Finish” to continue.Your installation is now complete.
Windows 2000:
Please make sure the Service Pack 3 is installed.To get this update please
Note:Windows 2000 comes installed with DirectX version 7.You must
have DirectX version 8.1 in order to install the M-Audio Ozone. The
M-Audio Ozone installer will automatically check for the correct
version of DirectX and install the latest Direct X update.This update
will be skipped if you already have DirectX version 8.1 (or higher) in
your system.
1. During this installation,the M-Audio Ozone must be powered off.Begin
the installation process by inserting the Drivers CD ROM in your
computer. Open the Ozone folder. Double-click on the Ozone.EXE
icon on your driver CD. The installer will install DirectX version 8.1
13
Download from Www.Somanuals.com. All Manuals Search And Download.
on your computer. Proceed with the DirectX installation by
clicking, "Next.”
2. Verify that you wish to continue installing DirectX 8.1 by clicking "Yes.”
3. Verify that you have read the license agreement and agree to the terms.
Click, "Yes," to continue.
4. Windows will need to restart your machine to complete the Direct X 8.1
installation. Click, "OK," to restart your system.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
5. This is the first setup window for installing the M-Audio Ozone drivers
after the installer has confirmed that you have DirectX version 8.1 (or
higher) installed on your system. Make sure your M-Audio Ozone is
powered off and that no other Windows programs are running, then
click,“Next,” to continue.
6. A “Digital Signature Not Found Window” will appear. As this is a
relatively new product, it does not have an official Windows Digital
Signature yet. Rest assured, our USB drivers are of the highest quality
and will not cause problems in your system. Click,“Yes.”
7. An M-Audio Setup Window will appear next. Make sure both Enable
Digital CD and Enable DMA Transfer Mode boxes are checked, then
click “Next.”
15
Download from Www.Somanuals.com. All Manuals Search And Download.
8. An M-Audio SetupWindow will come up,confirming a successful setup.
Click,“Next,” to successfully install the M-Audio Ozone.
9. Windows will prompt you to restart the computer.Make sure that“Yes,
restart my computer now,” is checked and then click,“Finish,” to restart
10. When you are completely restarted and at your desktop, power up the
M-Audio Ozone.A “Digital Signature Not Found” Window will appear
next.Again, just click “Yes.”
11. Another Digital Signature Not Found Box will appear.Click,“Yes,” again.
12. The driver is now installed in your computer.When you are completely
restarted and at your desktop, power up the M-Audio Ozone.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows ME:
Note: Windows ME comes installed with DirectX version 7.You must have
DirectX version 8.1 in order to install the M-Audio Ozone. The M-Audio
Ozone installer will automatically check for the correct version of DirectX
and install the latest Direct X update.This update will be skipped if you
already have DirectX version 8.1 (or higher) in your system.
1. During this installation,the M-Audio Ozone must be powered off.Begin
the installation process by inserting the Drivers CD ROM in your
computer. Open the Ozone folder. Double-click on the Ozone.EXE
icon on your driver CD. The installer will install DirectX version 8.1
on your computer. Proceed with the DirectX installation by
clicking, "Next.”
2. Verify that you wish to continue installing DirectX 8.1 by clicking "Yes.”
3. Verify that you have read the license agreement and agree to the terms.
Click "Yes" to continue.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Windows will need to restart your machine to complete the Direct X
8.1 installation. Click, "OK," to restart your system.
5. This is the first setup window for installing the M-Audio Ozone drivers
after the installer has confirmed that you have DirectX version 8.1 (or
higher) installed on your system. Make sure your M-Audio Ozone is
powered off and that no other Windows programs are running, then
click,“Next,” to continue.
6. An M-Audio Setup Window will appear next. Make sure both Enable
Digital CD and Enable DMA Transfer Mode boxes are checked, then
click “Next.”
18
Download from Www.Somanuals.com. All Manuals Search And Download.
7. An M-Audio SetupWindow will come up confirming a successful setup.
Click,“Next,” to successfully install the M-Audio Ozone.
8. Windows will prompt you to restart the computer. Make sure that
“Yes, restart my computer now,” is checked and then click,“Finish,” to
restart.When you are completely restarted and at your desktop,power
up the M-Audio Ozone.
Windows 98SE:
1. The M-Audio Driver CD should be inserted into the computer's CD-ROM
drive. In this example the CD-ROM drive is letter "D." (The letter of your
CD-ROM drive may be different, and you should change it accordingly.)
2. Now navigate to your CD-ROM drive.Browse the the M-Audio Ozone
Folder and run the EXE driver.
3. The first window explains that your operating system needs to have
Microsoft DirectX version 8.1 or better before continuing with
19
Download from Www.Somanuals.com. All Manuals Search And Download.
installation (if you have not previously installed this update). Click
“Next” to install DirectX 8.1.
4. Click next to verify that you would like to install Microsoft DirectX 8.1.
5. The next window shows the Microsoft DirectX 8.1 license agreement.
Click “Yes” to continue.
6. Click “OK” at the next window, to restart your computer.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
7. After restart, the next window reminds you to verify that the M-Audio
Ozone is disconnected from the USB bus before continuing, and that you
have closed all otherWindows applications. Do so now, then click “Next”
to continue.
8. An M-Audio Setup Window will appear next. Make sure both “Enable
Digital CD” and “Enable DMATransfer Mode” boxes are checked, then
click “Next.”
9. The next window will prompt you to connect the USB cable from your
M-Audio Ozone to your computer. Do not turn on the device
yet! Click “Next” to continue.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
10. The following window prompts you to restart your computer.With the
checkmark enabled, click “Finish” to restart.
11. AfterWindows has completely restarted, turn on your device using the
power button on the back of the M-Audio Ozone.A window will then
prompt you to click “Next” to continue.
12. The next window will prompt you to search for the best driver. Click
“Next” to continue.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
13. The next window defaults to browse to a specified location. Click
“Next” to continue.
14. In the next window, click “Next” to install the recommended driver.
15. The next window prompts you that the driver will now be installed.
Click “Next.”
23
Download from Www.Somanuals.com. All Manuals Search And Download.
16. The final window tells you that installation is complete. Click “Finish”..
After a few more‘automatic’ windows which do not require any action,the
installation procedure reaches completion, and your device is ready to use.
M-Audio Ozone and the Windows Sound System
After installation, the M-Audio Ozone’s Windows Multimedia drivers will
allow you to use the M-Audio Ozone as your Windows system sound
device. If the M-Audio Ozone is the only audio device installed in your
computer, then Windows will select it automatically. Otherwise, you may
need to tellWindows to use the M-Audio Ozone.To check yourWindows
Audio setting and select the M-Audio Ozone:
1. Go to the Start menu, and then choose Control Panel (in Windows
98SE and Me, you will need to go to Start/Settings, in order to get to
the Control Panel).
2. Open“Sounds andAudio Devices” (inWin 98SE,choose“Multimedia”),
then click the “Audio” tab.
3. Under “Sound Playback,” the default device should say “Ozone.” If it
does not, then drop down the list of devices and select “Ozone.”
4. Click “Apply,” then click “OK.” Close your Control Panel.
Macintosh Driver Installation
If you are using OS 9, you must first install Opcode’s OMS. OMS is a MIDI
manager program that is made by Opcode and is required to run the
M-Audio Ozone on the Macintosh in OS 9. OMS is available on the M-
Audio Ozone drivers page of our website, or can be installed from the
Driver CD.
Note: It is important that you install OMS before running the M-Audio
Ozone Installer.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
OMS Installation
To install OMS from the driver CD, locate the OMS 2.3.8 folder on this CD,
find the OMS installer program in the folder, and double click on its icon to
begin installation. Once this process completed successfully, you can move
on to the M-Audio Ozone Installer.
M-Audio Ozone Driver Installation
The current release version of the M-Audio Ozone driver requires
Macintosh operating system OS 9.2.2 or higher. Some updates are offered
free to Apple owners. Please check the Apple website at
First-time installation: If you power up your Mac with the M-Audio
Ozone attached and powered up, you will receive a message that an
“unknown USB device has been detected.” Click OK, and proceed with
the driver installation.You may also install the drivers first, and then plug in
the M-Audio Ozone.
ASIO Driver Installation
Most modern music recording software programs use an audio driver
standard called “ASIO.” If your music program uses ASIO, you should take
advantage of this low-latency audio driver by installing the ASIO driver. If
you’re unsure, check your music program’s documentation to see if it is
ASIO compliant.
After installation of the M-Audio Ozone drivers in either OS 9 or OS X,
you must copy the M-Audio Ozone’s ASIO driver directly into your music
program’s ASIO folder.
1. On your Macintosh hard drive, locate and open the folder for you
music program.Then, locate the ASIO folder.
2. On your M-Audio Ozone Drivers CD, open the Ozone folder, then the
ASIO folder. Hold the Option key, then click on the ASIO driver.
3. Drag the ASIO driver from the M-Audio Ozone Drivers CD over to
the music program’s ASIO folder. If you have more than one music
program that is ASIO compliant, repeat step 3 for each program.
- Mac OS 9:
1. Insert the Driver Software CD. Open the Ozone folder, then the USB
folder. There, you will find the M-Audio Ozone Installer program.
2. Run the M-Audio Ozone Installer by double clicking on it.This installs
all of the M-Audio Ozone’s extensions as well as the M-Audio Ozone
OMS Driver. However, YOU MUST HAVE OMS INSTALLED FIRST
25
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU RUN THIS INSTALLER PROGRAM. Otherwise, the
M-Audio Ozone OMS Driver will not be placed in the OMS folder.
Once installed, you should have two files, one in System Folder: Extensions
(M-Audio USB MIDI Support) and the other in System Folder: OMS
Preferences (M-Audio USB OMS Support.) For more information, scroll
through the Read me text which is presented on your screen during the
installation process.
- Mac OS X:
The drivers for Mac OS X are found on the Driver CD, which comes with
the product.You may also wish to check the M-Audio Ozone drivers page
of our website to make sure you have the most recent version.The driver
may be labeled “M-Audio Ozone” or “M-Audio USB.” The OSX Installer
Package icon looks like a cube of gelatin rising out of a cardboard box and
usually ends with the suffix “.pkg”.To install the software:
1. Double-click on the installer package.
2. When prompted, enter the administrator password you chose when
you installed OSX.
3. Follow the prompts to install the software.
OMS Configuration (Mac OS9 only)
If you have installed OMS (necessary only in Mac OS 9), you must now
configure it. Go to the Chooser under the Apple Menu, and make sure
AppleTalk is turned off (this is recommended, although OMS will sense that
it is on and prompt you to turn it off). If you are installing your M-Audio
Ozone’s driver and configuring OMS for the first time, follow these
instructions to configure OMS.
1. In the Opcode folder, which you will find on your hard drive, locate the
OMSApplications folder,then“OMS Setup.” Double click on“OMS Setup.”
2. OMS will inform you that it has not yet been configured. Click “OK.”
3. The“Create a New Studio Setup” dialog box now appears.Click“OK.” (If
this is not the first time you have created a Studio Setup in OMS, you will
have to go to the OMS File Menu and select Create a New Studio Setup).
26
Download from Www.Somanuals.com. All Manuals Search And Download.
4. The “OMS Driver Search” box asks you to choose the port on which
you’ve attached the M-Audio Ozone (either Modem or Printer). DO
NOT choose a port (since we’re using USB), just click “Search.” OMS
begins searching.
IMPORTANT: If the USB cable is not correctly hooked up to the
M-Audio Ozone, setup will fail.
5. “OMS Driver Setup” shows the M-Audio Ozone in a list when OMS
successfully finds the driver. Click “OK.” OMS will now define (shows
“Identifying”) the M-Audio Ozone output port.
6. The “OMS MIDI Device Setup” dialog box will appear showing the
M-Audio Ozone’s output port (labeled “M-Audio Ozone”) with an
open check box to the left of the port. You will now have to check this
open box to enable the output port. Click “OK.”
27
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Next,“My Studio Setup” appears with a file save dialog box over it. You
will now need to name and save your new studio setup (or use the
default name) before you can assign an instrument to the M-Audio
Ozone’s output (labeled“Ozone”). Assign your instrument (this step is
optional), and you are done.
You can run the OMS “Test Studio” utility by going to the “Studio” menu
and releasing the mouse on “Test Studio.” Playing a note on your keyboard
will give you an audio message from your computer,“MIDI received,” while
the arrow pointing to the keyboard icon flashes. Clicking on the keyboard
icon with the mouse pointer will send a tone cluster to the M-Audio
Ozone USB MIDI output port. Any sound module connected to the
M-Audio Ozone USB MIDI Out port should play the tone cluster.
You may now exit OMS Setup by quitting the application.The rest is up to
the configuration within your music software. Generally, this means
selecting “OMS Compatibility,” or “Open Music System” for your MIDI
system setup.
M-Audio Ozone and the Mac OS 9 Sound Manager
The Macintosh Sound Manager in OS 9 will allow you to select the
M-Audio Ozone as the system’s audio output device. This allows Sound
Manager applications such as iTunes or Quicktime to play through the
M-Audio Ozone, however, you cannot use ASIO and Sound Manager
simultaneously. Set the Macintosh's default Input and Output to "Built-in"
when using ASIO applications such as Reason.To check your computer’s
audio output setting and select the M-Audio Ozone:
1. Open theApple menu,then select“Sound” from the Control Panel’s list.
2. Under Input and Output,select“Ozone” from the list of available devices.
3. Close the Apple Sound Control Panel.
M-Audio Ozone and Mac OS X
Mac OS X will allow you to select the M-Audio Ozone as the system’s
audio output device.To change your Mac’s audio output setting to use the
M-Audio Ozone:
28
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Go to "System Preferences" in the Apple Menu.
2. Select the "Sound" preference panel, and click the "Output" tab.
3. Select "M-Audio Ozone" to choose the M-Audio Ozone as your
default output device.You can also select the “Input” tab to make the
M-Audio Ozone the default Input device.
The M-Audio Ozone Control Panel
When the M-Audio Ozone audio drivers are installed, M-Audio Ozone
Control Panel software is also installed onto your system. The Control
Panel gives you access to certain audio hardware parameters, plus some
status readouts. First, let’s locate the Control Panel on your particular OS.
Windows: In Windows, the M-Audio Ozone Control Panel shows up on
the task bar (located close to the “clock), and is also accessible from the
Windows Control Panel.
Mac OS 9: On your OS 9 hard drive, open the System Folder.Then, in the
Control Panels folder, locate the M-Audio Ozone Control Panel.You can
also access the M-Audio Ozone Control Panel from the Apple Menu
Control Panels.
Mac OS X: In the OS X Apple menu, go to System Preferences, then to
the M-Audio Ozone Control Panel.
The following screenshot shows the M-Audio Ozone Control Panel in
Macintosh OS X. (Please note that the functionality is similar in all versions
of the M-Audio Ozone Control Panel, so please read on regardless of your
OS). Let’s take a look at each element in the Panel. If you decide to make
and keep any changes, click “Apply.”
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Active Channels: A box that is checked indicates that a channel pair is
set to “Active.” Unchecking a box will deactivate that channel pair.When
the Control Panel is installed, both Inputs 1 & 2 and Outputs 1 & 2 are set
to “Active” by default.
Sample Depth: The default Sample Depth setting is “16-bit.” When the
Sample Depth is set to 16-bit,then your music recording software will only
allow you to record at 16-bit or lower. If you wish to record at a higher
Sample Depth (sometimes referred to as Bit Depth or Bit Width), change
this setting to “24-bit.”
Maximum Sample Rate: When both channel pairs are checked and
active, the Maximum Sample Rate will show a reading of 48000 (samples
per second). When either of the channel pairs is unchecked and
deactivated, the Maximum Sample Rate will show a readout of 96000.This
number represents the maximum sample rate at which your music
software will record (due to the limitations of the USB bus).
Latency:The amount of time it takes for audio to be converted to digital
information, processed by the system, and converted from digital back to
an analog audio signal is referred to as “Latency.” The M-Audio Ozone’s
audio driver plays a role in that latency, so overall latency can be affected
by your setting in the M-Audio Ozone Panel.
The more robust your system (a combination of processing power and
RAM), the lower the latency setting that it can handle.The default setting
is “medium.” After recording and playing back some audio, if you find that
the system seems to choke and stutter, or give you undesirable and audible
results such as crackling, try changing the Latency box to a higher setting.
Version Numbers: These numbers indicate the software version that is
currently loaded and in use. Shown are Preference Panel, USB Driver, and
Firmware version numbers.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection Status: The M-Audio Ozone Control Panel will only be
accessible when your M-Audio Ozone is connected to the computer and
recognized by the system.When the M-Audio Ozone is not connected, the
panel will either be grayed out, or a message will pop up indicating that the
M-Audio Ozone is not recognized.
In Mac OS X (only), when your M-Audio Ozone is connected to your
computer’s USB port and recognized by the system, this section will
indicate a “Connected to M-Audio Ozone” status.
Application Software Setup
Once the M-Audio Ozone driver has been installed, you will need to
configure your MIDI and audio application software to utilize the M-Audio
Ozone. The manner in which this is done varies between applications, so
we can just cover the basics here.
Enabling MIDI: Generally with both the Mac and PC, most MIDI
applications have a MIDI port configuration or settings dialog box,
sometimes called “MIDI Devices” or “MIDI Setup.” It is within this dialog
box that you will select or enable your MIDI input and output devices.
If the M-Audio Ozone drivers are properly installed, then the port
selection in this case will be the M-Audio Ozone In-1 (“Port 1” on Mac) in
the input column, and then M-Audio Ozone Out-1 (or Port 1) in the
output column. Input 1 (or Port 1), corresponds to the information that
will be sent from the M-Audio Ozone keyboard to your computer.
M-Audio Ozone Out-1 (or Port 1), corresponds to the MIDI information
sent from your music application to the physical MIDI output on your
M-Audio Ozone that is marked “USB.” Make sure that those items are
highlighted or checked.The output port that you select on a specific MIDI
track within your sequence will output MIDI information to the keyboard
or sound module that is attached to that port.
Enabling Audio: After installing the M-Audio Ozone drivers and opening
a music program for the first time, you may be prompted to profile your
new audio device—the M-Audio Ozone. If you’ve used the program
before, you’ll have to do this yourself, or “manually.” How you do this will
vary from program to program, so check your user’s guide.
On both Mac and PC, there should be an “Audio Preferences” or “Audio
Setup” screen within your music software (though there are a few music
programs that are MIDI only). Once you’ve profiled the M-Audio Ozone,
make sure that the inputs and outputs of your audio software are set to use
the M-Audio Ozone for recording and playback. In ASIO applications, make
31
Download from Www.Somanuals.com. All Manuals Search And Download.
sure that the M-Audio Ozone audio driver is set to“M-Audio OzoneASIO.”
Within your music application, when you assign an audio track to receive
its input from the M-Audio Ozone Channel 1 or Channel 2—whether it’s
the Mic In and Instrument In, or when using the Aux Inputs in “Record”
mode—you will set the input device to:
•
In a non-ASIO application, possible choices will be “Ozone-L,” “Ozone-
R,” or “Ozone Stereo.”
•
In an ASIO application, your input choices will be “Ozone ASIO 1” and
“Ozone ASIO 2.”
Your audio device output selection, in either a non-ASIO or an ASIO
application, will be “Ozone 1/2.”
M-Audio Ozone Hardware Installation
Installing your M-Audio Ozone involves simply attaching it to your
computer’s USB port via the standard USB cable included with the
product. Find a good spot around your computer station to place the
M-Audio Ozone.The USB port on your computer is a small, rectangular
connector and is usually found in a group of two. The“device end” of your
USB cable is roughly square in shape, and should fit easily into the USB
connector on your M-Audio Ozone.Take the “computer end” of the USB
cable and plug it into the USB port on the back of your computer.Take the
“device end” of the USB cable and plug it in to the USB port on the back
panel of the M-Audio Ozone.
We recommend that you power down (turn off) your computer for a first
time installation. Plug in the M-Audio Ozone using the supplied power
adapter and turn on the power.
The audio outputs of the M-Audio Ozone should be connected to your
audio monitoring system: a mixer, an audio receiver, or a pair of powered
speakers. Further audio and MIDI connection instructions will be found in
the following sections,“M-Audio Ozone MIDI Setup” and“M-Audio Ozone
Audio Setup.”
M-Audio Ozone Audio Setup and Control
The M-Audio Ozone provides two inputs (Mic and Instrument), and two
line outputs (Output 1 and 2).The M-Audio Ozone also provides a pair of
Aux Inputs which can be used to monitor external gear, or can double as
line inputs when switched to “Record” mode.A Headphone Out on a 1/4”
stereo TRS jack is included for monitoring with headphones.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Each 1/4” line out jack (Output 1 and 2) sends a -10dB unbalanced signal
on 1/4”TS plugs (tip-sleeve).They are designed to be plugged into a mixer,
stereo receiver, powered speakers, or any other line level input such as a
mixdown deck or tape recorder.
Channel 1 of the M-Audio Ozone provides a microphone input on a
balanced XLR connector. Channel 2 has a balanced 1/4” TRS (tip-ring-
sleeve) connector for connecting a balanced or unbalanced instrument level
signal.This input is ideal for recording an electric guitar, bass, or an acoustic
guitar with a pickup. Either one of the M-Audio Ozone’s input channels can
be recorded individually, or you can record them simultaneously.
The Aux Input accepts a stereo signal via a TRS cable.You may need to
purchase a cable that converts a pair of stereo outputs (individual RCA or
1/4”TS) into a single 1/4”TRS connector to plug into the M-Audio Ozone’s
Aux Input.Your M-Audio dealer should have a cable like this, often called
an “insert cable.”
You may connect the output of a line level instrument such as an electronic
keyboard, instrument preamp, or the output of a CD player or similar
line-level device to the M-Audio Ozone’s Aux Inputs.
The M-Audio Ozone’s Mic In (Channel 1), accepts a balanced, low
impedance microphone signal. If your microphone is a condenser type that
requires phantom power, you may apply phantom power by engaging the
Phantom Power switch (see the section entitled “Phantom Power”). The
Instrument In (Channel 2) will accept a balanced or unbalanced high
impedance guitar, keyboard, or microphone.
The following diagrams illustrate two scenarios, intended as examples of
how the M-Audio Ozone might be used.Typical Setup #1 shows the M-
Audio Ozone with a microphone plugged into the Mic In on Channel 1,and
an electric guitar plugged into the Instrument In on Channel 2.The main
outputs (Output 1 and 2) of the M-Audio Ozone are plugged into a DAT
recorder, with the recorder’s outputs connected to a monitoring system.
Typical Setup #2 shows a drum machine plugged into the Aux Inputs, with
Outputs 1 and 2 plugged into a monitoring system.The drum machine is
also connected to the M-Audio Ozone MIDI Out “USB.”
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Mic and Instrument Inputs
Channel 1 of the M-Audio Ozone gives you a high gain, low noise
microphone preamp. It provides a low impedance microphone input on an
XLR connector with optional phantom power. A dynamic, condenser, or
any other type of low impedance microphone will interface easily with the
M-Audio Ozone’s Mic Input.
Channel 2 gives you a high impedance instrument preamp, designed to add
preamp gain to an electric or acoustic guitar, keyboards, or even a high
impedance mic. However, you may also attach a direct box or passive
transformer to the M-Audio Ozone’s Mic Input (Channel 1), which will
then allow you to plug another electric or acoustic guitar or other high
impedance instrument into the M-Audio Ozone’s Mic Input. Additional
information on using the Mic and Instrument Ins will be found in the next
two sections.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Input Gain
The M-Audio Ozone provides up to 60dB of gain on the Channel 1 Mic In
and 40dB of gain on the Channel 2 Instrument In. Microphones typically
emit a low signal level, requiring a "pre-amp" such as the M-Audio Ozone
provides. Other instruments, such as guitar pickups and even some
keyboard sound modules, will also benefit from a bit of punch from the
M-Audio Ozone preamps.
Plug in your mic or instrument with the gain controls turned down, then
turn the gain up incrementally while testing the mic or playing the
instrument. When the signal LED shows fairly consistent activity, you’ve
reached a good signal level for the M-Audio Ozone mic preamp. Some
users may wish to experiment a little further to find what audibly might be
referred to as a "sweet spot." Note that when the "clip" LED lights, it is
indicating that the preamp output signal is clipping, or is too close for
comfort. Let your ears be the judge, but when the clip LED lights and stays
lit,you are approaching or have reached distortion in your M-Audio Ozone
signal.The best method is to turn up the gain, and then turn it down once
you’ve started to clip the input signal.
You must also consider the level that is being sent from the M-Audio
Ozone to your recording software. Check the input meters within your
software and make sure that they are neither too low nor clipping (too
“hot”). An adjustment in gain on the M-Audio Ozone may be necessary,
but your optimal recording level within your software should approach but
never reach the maximum level.Additionally, because the M-Audio Ozone’s
preamps provide quite a bit of gain, it is recommended to turn the gain all
the way down on unused inputs.
You will find more information on setting record levels in the manual of
your music software. Understand that in digital recording, clipping the
meters in your program is never a good thing. If your level goes into the
red once, you’ve got distortion!
Phantom Power
Unlike dynamic microphones, many "condenser microphones" need to
receive a DC voltage (generally 48V) from an external source before they
can generate an output signal. If the condenser mic doesn’t come with its
own power supply, then phantom power must be applied from the preamp.
Setting the Phantom Power Switch to send phantom power on the
M-Audio Ozone will send the necessary voltage to the XLR Mic Input.
Phantom power will not affect a dynamic mic adversely, so it is fine to have
a dynamic mic at the XLR input while phantom power is switched on. Just
35
Download from Www.Somanuals.com. All Manuals Search And Download.
to be safe, check your mic’s documentation to see if it will accept or needs
phantom power. Some ribbon mics definitely should NOT receive
phantom power, as this could damage them.
Using the Aux Inputs
The M-Audio Ozone has a pair of “Aux Input” line inputs, both on a single
1/4” TRS jack. It is designed so that a single connector contains both the
left and right input from a stereo source, such as a synthesizer, drum
machine, or CD player.This input is unbalanced, –10dBV line level. Below
is an example of the type of cable you will need to connect to the Aux
Input—commonly referred to as an “Insert Cable.”
The Aux Input has two modes—Monitor and Record. In Monitor mode,
the Aux Input is mixed with the signal coming from your computer via the
USB cable, and plays through Outputs 1 and 2 and the Headphone Out. In
Record mode, the Mic In (Channel 1) and Instrument In (Channel 2) are
disabled so that you can record the Aux Inputs to your computer. In other
words, Record mode turns the Aux Inputs into line inputs to your
computer, and is useful if you want to record a line level stereo source.
You may, for example, want to use the Aux Input—in Monitor mode—to
monitor a sound module that is being triggered by the M-Audio Ozone’s
MIDI Out jack.Then, when your MIDI sequence is complete, you may want
to record that sound module as an audio track. Recording your MIDI
sequences as audio tracks allows you to apply effects and EQ,and then mix
those tracks with other audio tracks (such as vocals and guitar) entirely
from within your computer.
To switch from Monitor mode to Record mode, simply press the
Monitor/Record switch (located next to the Aux Input on the back panel)
to the “in” position. Once you have done that, you will no longer hear the
audio source that is plugged into the Aux Input.There are two ways that
you can now monitor what you are about to record:
•
•
Use the M-Audio Ozone’s built-in zero-latency Direct Monitoring (see
next section) - OR -
Use your ASIO or WDM-compliant (such as Cakewalk’s “Sonar”)
program’s input monitoring feature. See your music software user’s
guide for more info.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Also, as we mentioned, using Record mode defeats the Mic and Instrument
inputs, so you will not be able to listen to or record from those inputs
when the Aux Input is in Record mode.
Another example is to use the Record mode only to switch Channel 1 and
Channel 2 to line inputs, for the purpose of recording a tape deck, CD
player, or other stereo line level source into your computer. Set the
Monitor/Record switch to Record (the “in” position), then plug in your
stereo source using an insert cable.
Once you have set up the M-Audio Ozone to Record from the Aux Input,
you will have to set up tracks in your music program for recording.
Using Direct Monitor
When a mic or instrument is plugged into the inputs of the M-Audio
Ozone, its journey has just begun.The signal needs to be converted to a
digital signal, which then gets sent to the computer via the USB pipe. From
there,it gets sent to your music software and processed,then turns around
and comes all the way back. Even though the M-Audio Ozone uses the
latest hardware and software technology, it might take a few fractions of a
second to make this trip. Although this delay is imperceptable when the
performance is played back, it can be distracting when you’re performing
music. To compensate for this delay, the M-Audio Ozone has a feature
called Direct Monitor.
Direct Monitor sends the signal from the Channel 1 and 2 inputs directly
to the Outputs, without any of the delay caused by traveling to and from
the computer. The Direct Monitor level knobs control the level of the
signal from the Channel 1 and 2 inputs to the Main and Headphone
Outputs. Use these level knobs to set the monitoring level of the mic or
instrument that you are recording relative to the audio tracks that are
playing from your computer.
The Direct Monitor system has a switch on the rear panel, labeled “Direct
Monitor Stereo/Mono.”When this switch is set to Stereo, Input Channel 1
will be sent to the Left Output and Input Channel 2 will be sent to the
Right Output. If you want to hear your source in mono through both
outputs, set this switch to Mono.The Mono setting is useful when you are
recording individual instruments, as opposed to a stereo source.
When using Direct Monitor, you will need to disable any monitoring
feature in your computer recording software. Otherwise, you will hear
your input played back twice—once through Direct Monitor, and again
from your computer. See if there is a way to turn off the record or input
37
Download from Www.Somanuals.com. All Manuals Search And Download.
monitoring, mute the channels you are recording to, or send their output
to another bus.
In a typical Direct Monitor application, plug your microphone and guitar
into Channel 1 and Channel 2 on the rear panel. Arm a pair of inputs in
your computer recording software and set their recording levels using the
Gain controls on the M-Audio Ozone.As detailed in the previous sections,
you want the recording level to be as high as possible without distorting.
Make sure that the recording software is not outputting the audio you’re
recording, or else you will hear the signal played twice from the outputs.
Next, set the Direct Monitor Level for each Channel Input to your
speakers or headphones and you are ready to record. If you are recording
your mic and guitar while listening to tracks already recorded in your
computer,you might want to listen once and set your Direct Monitor Level
relative to the tracks playing from your computer.
NOTE: In this scenario, you may want to hear your mic and guitar in
the center of the stereo image. To achieve this, locate the Direct
Monitor switch on the M-Audio Ozone rear panel, and switch it to
the “Mono” position.
In Mac OS X (only), when your M-Audio Ozone is connected to your
computer’s USB port and recognized by the system, this section will
indicate a “Connected to M-Audio Ozone” status.
M-Audio Ozone MIDI Setup and Control
A typical MIDI system would include your M-Audio Ozone, a computer,
MIDI sequencing software,software synthesizers and/or a MIDI compatible
sound module.This type of setup can be connected as follows:
The M-Audio Ozone is connected to the computer via the USB port
connectors, using the supplied USB standard cable.
The M-Audio Ozone can play any software synthesizers that are installed
in your system, as well as the synthesizer that is part of an internal sound
card.This will depend on how you set up your software (see the section
entitled “Using the M-Audio Ozone in your Application Software”).
The “USB” MIDI Output of the M-Audio Ozone can be connected to the
MIDI In of a sound module. The audio output of the sound module can be
plugged directly into the Aux Input of the M-Audio Ozone.The M-Audio
Ozone’s Output 1 and 2 can then be plugged into a sound system, or into
a mixer, which is then connected to a sound system (see the section
entitled “M-Audio Ozone Audio Setup”).
38
Download from Www.Somanuals.com. All Manuals Search And Download.
In the following setup, the M-Audio Ozone is being used as a MIDI
controller as well as a MIDI interface, inputting MIDI data to the computer
and its application software, and outputting MIDI to a sound module from
which sounds will be produced.The M-Audio Ozone as a controller may
also send MIDI information to any installed software synthesizer,
outputting the audio from the M-Audio Ozone’s audio outputs.
Additionally, the M-Audio Ozone may be used as a standalone keyboard
controller, independent of the computer and its USB port.You will want to
use the MIDI out port that is labeled “Keyboard.” A setup such as this may
be used in a performance situation, or when you wish to use the keyboard
without the computer.
M-Audio Ozone MIDI Functions
MIDI is the acronym for Musical Instrument Digital Interface, which makes
all digital musical instruments equipped with this standardized interface
able to exchange their MIDI data or “talk” to each other.
To explain how MIDI works on your instrument in more detail, the
following descriptions outline the MIDI functions of the M-Audio Ozone,
which allow you to connect the keyboard to other MIDI instruments and
to your computer.The versatile MIDI capability of the M-Audio Ozone will
offer you tremendous power in a MIDI environment.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
The keys on the M-Audio Ozone, in conjunction with the MIDI/SELECT
button, give you the extra programming capability that is unique to
M-Audio’s line of MIDI controllers (including the M-Audio Ozone, Oxygen8
and Radium).You can use the Data Entry key to enter in values, or the keys
that are labeled with numbers.The keys labeled for specific MIDI functions
can be used to assign that function to the data slider.The “Set Ctrl” key can
be used with the numeric value keys to program the rotary faders to send
MIDI controller information on specific MIDI channels.
MIDI Functions In Standalone Mode
To transmit MIDI data from your keyboard to other professional MIDI
instruments, purchase a standard MIDI cable and use it to connect the
MIDI OUT jack of your M-Audio Ozone labeled “Keyboard” to the MIDI
IN jack of the other instrument.
1. Power up the M-Audio Ozone.
2. Make sure that the M-Audio Ozone’s MIDI port ”transmit” channel
matches the MIDI “receive” channel of the other instrument.
3. Please refer to the diagram in the section entitled “Setting Up Your
MIDI Studio” for audio connections.
Default Settings ofThe M-Audio Ozone
The M-Audio Ozone will always select the following values as parameters
when the power is turned on.
•
•
•
•
•
•
•
•
•
•
•
•
Transmit MIDI Channel no. 1
Default Octave will be from C4(60) to C6(84)
Default After Touch value will be 0
DefaultVelocity value will be 0
Default Reverb Depth value will be 64
Default Pan Pot value will be 64
DefaultVolume value will be 127
Default CC Data value will be 0
Default CC no. value will be 0
Default Control Change (CC-00=0,CC-32=0) message to be transmitted
Default Program Change (PG=1) message to be transmitted
Default MIDI-controller knob-assignments on MIDI ch. 1
Utilizing the Programming Assignment Keys
This section contains the information you will need to program the
M-Audio Ozone, and to send any MIDI parameter data from the M-Audio
Ozone keyboard.You may set the data slider to send MIDI controller data
40
Download from Www.Somanuals.com. All Manuals Search And Download.
of your choice, send program change data from the keyboard, select the
MIDI transmit channel of the M-Audio Ozone, set the octave or pitch of
the keyboard, and program the eight rotary controllers.
DATA ENTRY Assignments: Pressing the MIDI/SELECT button then
pressing a key labeled by its MIDI function (such as velocity offset,aftertouch,
reverb depth, pan pot, volume, CC data) and then moving the data entry
slider, allows you to select the transmitting value of the chosen function.
For example, if you want to change the value of the velocity offset, first
press the MIDI/SELECT button and then the velocity key. Second, change
the data entry slider to the value you want. Finally, press the MIDI/SELECT
button again to finish the change.
To assign any MIDI control value to the data slider:
1. Press the MIDI/Select button
2. Press the CC No. key (low B)
3. Press the number keys to choose the MIDI controller number
4. Press the Enter key
5. Press the MIDI/Select button to finish your selection.
For a chart of MIDI control change values, see Appendix A in this manual.
You can also use the data slider to send this MIDI controller information
in real time. When the M-Audio Ozone powers up, the DATA ENTRY
slider defaults to a MIDI controller value of 7.A Controller 7 message is
the equivalent of a MIDI volume message. Once you’ve selected one of the
keys that represents a controller value, i.e., velocity, aftertouch, pan pot,
etc., or assigned a value using the number keys, the DATA ENTRY key then
takes on that value and will transmit that type of controller information
when the slider is moved
SET CTRL Key: Pressing the MIDI/SELECT button and then the SET
CTRL key will allow you to begin programming the rotary control knobs.
In order to change the value of each knob (1 - 8),you need to do as follows:
1. Press MIDI/SELECT, then the Set Controller key, F3 (marked “SET
CTRL.)” The display will show a small “n” to indicate that the desired
controller knob “number” should be entered next.
2. Choose the number of the desired controller knob using the number
key group (1 - 8).Then press the Enter key.The display will show a “P”
in anticipation of the “parameter” number.
3. Assign the desired MIDI controller parameter number using the
number key group (1-127),then press Enter.The display will show a“C”
in anticipation of the MIDI “channel” number. See chart,“Appendix A.”
41
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Assign the MIDI channel number on number key group (1-16) then
press Enter.This channel assignment will apply only to the controller
knob that you are programming.
5. You can select up to five banks of presets for the M-Audio Ozone’s
keyboard, P1-P5, by pressing the MIDI/SELECT button. This is most
effective for stand-alone mode, not for all soft-synth presets.
6. Finally, Press MIDI/SELECT key again to finish assigning values to the
controller knob.
RESET Key: Pressing the MIDI/SELECT button, followed by the RESET
key and then the Enter key, will send out a message to return all external
MIDI instruments to their default setting. Press the MIDI/SELECT button
again to complete the process.
Flat and Sharp Keys: By pressing the MIDI/SELECT button and the flat
or the sharp key, you will shift the active keyboard pitch one note (half-
step) higher,or lower. For example,if you want to change the pitch 2 notes
down, press MIDI/SELECT button and the flat key twice. Press the
MIDI/SELECT button to finish the change.
To change the M-Audio Ozone’s octave range, press the the “Octave Up”
or “Octave Down” button however many times you wish to shift the
octave range. Press the MIDI/SELECT button to finish the change.
MIDI CHANNEL Select: Pressing the MIDI/SELECT button and then
pressing the MIDI CHANNEL key allows you to select the transmitting
channel for your keyboard.The default Channel is 1 when the keyboard’s
power is turned on.To set the MIDI channel to 2, for example:
1. Press the MIDI/SELECT button.
2. Press the key labeled “MIDI CHANNEL,” on the keyboard.
3. Press the key labeled 2, on the keyboard, then press the key labeled
“Enter,” also on the keyboard.Lastly,press the MIDI/SELECT button one
more time (this will change the MIDI transmit channel from 1 to 2.)
Control Change Data Entry by Numeric Keypad: M-Audio Ozone
allows you to use the numeric keys, instead of the data entry slider, to
specify the Control Change parameter data.This is done by pressing the
MIDI/SELECT button, CC (No. or Data) key, required number key(s), and
the Enter key.As an example, to assign a Control Change value of 7, and
CC Data value of 123:
1. Press the MIDI/SELECT button.
2. Press the CC No. key.
3. Press the key labeled 7.
4. Press the Enter key, in order to specify the Control Change as 7.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Press the CC Data key.
6. Press the number keys 1, 2 and 3, in order.
7. Press the Enter key, to specify the value 123, then press the
MIDI/SELECT button.This completes the process.
Program Key: By pressing the MIDI/SELECT button and the Program key,
then numeric keys, and finally the Enter key, you can select any patch
number between 1 and 128. For example, if you want to change the voice
to 67 (General MIDITenorSax), Press the MIDI/SELECT button and 6, 7 on
the numeric keys, then press the enter key and MIDI/SELECT button again
to finish this action.
Please note: After you press the enter key, the LED display will show
“—-“ and will not disappear until you press the MIDI/SELECT button
to finish your choice. After you press the Cancel key, the LED display
will also show blank, and will not disappear until you press the
MIDI/SELECT button to finish your choice.
Presets:The M-Audio Ozone can save five Presets in memory.This allows
you to assign 8 controller values to the faders and knobs in one Preset,and
then assign 8 different values to those same faders and knobs. In this
manner, you may change settings without losing your current settings.To
change Presets, press the MIDI/SELECT button, then the UP/DOWN
buttons, choosing the desired Preset from the five Preset banks available.
The display will read “P1” through “P5” while you are changing Presets.
The chart on the next page lists the factory default Presets,useful in a variety
of software programs and performance scenarios.These default Presets use
the Preset memory banks 1 through 5. Banks 1 through 5 are not write-
protected and so when applying the above method of editing and saving
customized Presets according to your wants and needs, they can be written
over. If you ever wish to restore the factory default Presets, simply hold
down the MIDI/Select button while powering up your M-Audio Ozone.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
M-Audio Ozone Preset Chart
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Support & Contact Information
For additional technical assistance, contact M-Audio Technical Support by
telephone (626-445-8495, 9-5 PST M-F), by fax (626-445-7564) or by
e-mail ([email protected]).
If you have questions, comments or suggestions about this product, or any
M-Audio product, we invite you to contact us directly at:
M-AUDIO U.S.
45 E. Saint Joseph St.
Arcadia, CA 91006-2861
U.S.A.
M-AUDIO U.K.
Unit 5, Saracen Industrial Estate
Mark Rd.
Hemel Hempstead, Herts HP2 7BJ
England
Sales Information:
Sales Information (email):
Tech Support:
Tech Support (email):
Fax:
Internet Home Page:
626-445-2842
626-445-8495
Sales Information:
Sales Information (email):
Technical Support:
44 (0) 144 241 6590
44 (0) 871 717 7102
626-445-7564
Fax:
44 (0) 144 224 6832
Internet Home Page:
M-AUDIO Canada
1400 St-Jean Baptiste Ave., #150
Quebec City, QC G2E 5B7
Canada
M-AUDIO France
Unit 5, Saracen Industrial Estate
Mark Rd.
Hemel Hempstead, Herts HP2 7BJ
England
Tel:
418-872-0444
418-872-0034
Sales Information:
0810 001 105
Fax:
Email:
Internet Home Page:
Technical Support:
0820 00 731
Fax:
44 (0) 144 224 6832
Internet Home Page:
M-AUDIO Deutschland (Germany)
Kuhallmand 34
M-AUDIO Japan
Annex Buliding 6F
2-18-10 Marunouchi
Naka-Ku, Nagoya 460-0002
Japan
D-74613 Ohringen
Germany
Sales Information:
Sales Information (email):
Technical Support:
Technical Support (email):
Fax:
49 7941 98 7000
49 7941 98 70030
Tel:
81 52 218 3375
81 52 218 0875
Fax:
Technical Support:
Email:
Internet Home Page:
0820 00 731
07941 98 70070
Internet Home Page:
45
Download from Www.Somanuals.com. All Manuals Search And Download.
M-Audio Ozone Warranty Information
M-AUDIO warrants that this product is free of defects in materials and
workmanship under normal conditions for 90 days, so long as the product
is: owned by the original purchaser; the original purchaser has proof of
purchase from an authorized M-AUDIO dealer; and the purchaser has
registered his/her ownership of the product by sending in the completed
warranty card.
In the event that M-AUDIO receives written notice of defects in materials
or workmanship from such an original purchaser, M-AUDIO will either
replace the product, repair the product, or refund the purchase price at its
option.In the event any repair is required,shipment to and from M-AUDIO
and a nominal handling charge shall be borne by the purchaser. In the event
that repair is required, a Return Authorization number must be obtained
from M-AUDIO.After this number is obtained, the unit should be shipped
back to M-AUDIO in a protective package with a description of the
problem and the Return Authorization clearly written on the package.
In the event that M-AUDIO determines that the product requires repair
because of user misuse or regular wear, it will assess a fair repair or
replacement fee.The customer will have the option to pay this fee and have
the unit repaired and returned, or not pay this fee and have the unit
returned unrepaired.
The remedy for breach of this limited warranty shall not include any other
damages. M-AUDIO will not be liable for consequential, special, indirect, or
similar damages or claims including loss of profit or any other commercial
damage, even if its agents have been advised of the possibility of such
damages, and in no event will M-AUDIO's liability for any damages to the
purchaser or any other person exceed the price paid for the product,
regardless of any form of the claim. M-AUDIO specifically disclaims all
other warranties, expressed or implied. Specifically, M-AUDIO makes no
warranty that the product is fit for any particular purpose.
This warranty shall be construed, interpreted, and governed by the laws of
the state of California.If any provision of this warranty is found void,invalid
or unenforceable, it will not affect the validity of the balance of the
warranty, which shall remain valid and enforceable according to its terms.
In the event any remedy hereunder is determined to have failed of its
essential purpose, all limitations of liability and exclusion of damages set
forth herein shall remain in full force and effect.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
M-Audio Ozone Technical Specifications
General
•
•
Supports 24-bit or 16-bit audio input or output
Supports the following sampling frequencies (Hz): 8000, 11025, 12000,
16000, 22050, 24000, 32000, 44100, 48000, 88200, 96000
•
(Note: Because of USB bandwidth and device hardware constraints,
there are limitations on what combinations of bit width and sampling
frequency can be used in full-duplex mode (i.e.-input and output active
simultaeneously))
1/4" Outputs 1 & 2
•
•
•
Dynamic Range: 100 dB (typical, -60 dB input,A-weighted)
S/N: 100 dB (typical,A-weighted)
THD: <0.002% (typical)
Mic/Inst Input
•
•
•
Dynamic Range: 100 dB (typical, -60 dB input,A-weighted)
S/N: 100 dB (typical,A-weighted)
THD: <0.002% (typical)
1/4 AUX Inputs 1 & 2
•
•
•
Dynamic Range: 95 dB (typical, -60 dB input,A-weighted)
S/N: 95 dB (typical,A-weighted)
THD: <0.009% (typical)
Tested to
comply
with FCC
Standards
For Home or Studio Use
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A - MIDI Controller Information
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B - M-Audio Ozone Block Diagram
49
Download from Www.Somanuals.com. All Manuals Search And Download.
|