Web Interface User’s Guide
ADSL Ethernet & USB Combo Router
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
Introduction
The Lynx L-210 is the perfect high-speed WAN bridge/router. This full-featured product is
specifically designed to connect to the Internet and directly connect to your local area network via
high speed 10/100 Mbps Ethernet. The Lynx L-210 has also full NAT firewall and DMZ services to
block unwanted users from accessing your network.
For game users, the Lynx L-210 had already pre configured for several low latency game ports.
Just click on the game you are playing on line and the rest is done for you
The Lynx L-210 is fully compatible with all PCs; as long as the PC supports an Ethernet interface
and is running a TCP/IP protocol stack, your PC can have high-speed WAN access. So, plug in the
Lynx L-210 (refer to easy start guide), configure it (per your ISP’s requirements) and enjoy the fast
Internet access like never before.
1.1 Features
ADSL/ATM Support
•
•
•
•
•
•
•
•
•
•
ANSI T1.413 issue 2, ITU-T G.992.1 (G.dmt) and G.992.2 (G.lite) compliant
ADSL2, ADSL2+, RE-ADSL compliant
Rate Adaptive modem at 32 Kbps steps
Dynamic Adaptive Equalisation to improve Carrier’s service area
Bridge Tap Mitigation support
ATM Layer with Traffic shaping QoS Support (UBR, CBR, VBR-rt, VBR-nrt)
AAL ATM Attributes - AAL5
Multiple PVC up to 8 support (Bridge Support)
Spectral compatibility with POTS
F5 OAM Loopback/Send and Receive
Encapsulation Support
•
•
•
•
•
RFC2684 Bridge and Routed LLC and VC Mux support
RFC2364 PPPoA Client support
RFC2516 PPPoE Client support
RFC2225/RFC1577 Classical IP Support
Transparent Bridge Support
Network Support
•
•
•
•
•
•
•
•
•
•
•
•
•
Static IP, Dynamic RIP routing support
IP/TCP/UDP/ICMP/ARP/RARP Application Support
Network Address Translation (NAT)
Port Mapping/Forwarding
Easy setup of Port Forwarding rules for popular Games/Application
NAT Application Level Gateway for popular applications
DHCP Server/Relay/client
DNS Relay Agent
DMZ support
Single Session IP Sec and PPTP/L2TP VPN pass through support
PPP Always on with configurable timeout
PPP Dial on Demand
Universal Plug and Play Support
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Management Support
•
•
•
•
•
•
•
Web Based HTTP management GUI
TFTP/FTP Support for Firmware Upgrade
Web Based Firmware Upgrade (Local)
Soft Factory Reset Button via Web GUI
Diagnostic Test (DSL, OAM, Network, Ping Test)
Telnet/CLI (Read Only)
Syslog Support
Security Support
•
•
•
•
•
NAT for basic Firewall support
Packet Filtering Firewall Support
Stateful Packet Inspection Support
Protection against Denial of Service attacks
Password Authentication to Modem
External Connectors
•
•
•
•
•
1 x RJ-11 Telephone socket for ADSL line
1 x RJ45 for 10/100Base-T Ethernet (MDI-X)
1 x USB 1.1 Type B
1 x DC Jack for Power Input
1 x Factory Default Reset Button
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Your gateway at a glance
The Lynx L-210 may have different ports and LEDs. Let’s take a look at the different options.
Depending upon your model, it may have some or all of the features listed below
2.1 Ports and buttons
Reset and Restore to Factory Defaults: The restore to factory defaults feature will set the Lynx L-
210 to its factory default configuration by resetting the Lynx L-210. You may need to place the Lynx
L-210 into its factory defaults if the configuration is changed, you loose the ability to interface to the
Lynx L-210 via the web interface, or following a software upgrade,. To reset the Lynx L-210, simply
press the reset button for about ~ 10 seconds. The Lynx L-210 will be reset to its factory defaults
and after about 30 ~ 40 seconds the Lynx L-210 will become operational again.
LAN (local area network) port(s): connect to Ethernet network devices, such as a PC, hub,
switch, or routers. Some Lynx L-210 came with a single LAN connection and some come with four
LAN connections. Depending on the connection, you may need a cross over cable or a strait
through cable.
Power is where you connect the power. Make sure to observe the proper power requirements.
The require power is 9 volts.
USB (universal serial port): connects to a PC’s USB port. The Lynx L-210 only supports
Window’s based PCs via an RNDIS driver (included in the software).
DSL port: This is the WAN interface that connects directly to your phone line.
2.2 LED description
1. PWR/POWER
Lights up when power is supplied to the Lynx L-210.
2. ETH/ACT
Lights up when the Ethernet cable is properly connected from your Lynx L-210 to the
Ethernet Card.
Flickers when the ADSL is transmitting/receiving data.
3. USB
Lights up when the USB connection is established.
Flickers when the ADSL is transmitting/receiving data
4. DSL
Lights up when the DSL connection is established.
Flickers when the Lynx L-210 is trying to establish a connection with the ADSL
Service Provider.
5. PPP/Internet
Lights up when the PPP connection is established.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Installing your Lynx L-210
1. Locate an optimum location for the Lynx L-210.
2. For connections to the Ethernet and DSL interfaces, please refer to the easy start guide.
3. Connect the AC Power Adapter. Depending upon the type of network, you may want to put
the power supply on an uninterruptible supply. Only use the power adapter supplied with the
Lynx L-210. A different adapter may damage the product.
Now that the hardware installation is complete, proceed to Chapter 4: Setting up your Lynx L-210
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
Setting up your Lynx L-210
This section will guide you through your Lynx L-210’s configuration. The Lynx L-210 is shipped with
a standard PPP configuration.
4.1 Log into your Lynx L-210
To configure your Lynx L-210, open your web browser. You may get an error message at this point;
this is normal. Do not panic!. Continue following these directions. Type the default IP address
(192.168.1.1) Press the Enter key and the following screen, shown in Figure 1 will appear. The
default user name is admin (case sensitive) and the password is admin (case sensitive).
Note: Before setting up your Lynx L-210, make sure you have followed the easy start guide.
You should have your computers configured for DHCP mode and have proxies disabled on
your browser. Also if you access the Lynx L-210, and instead of getting a login screen, the
browser instead displays a login redirection screen, you should check your browser's
setting, and verify that JavaScript support is enabled. Also, if you do not get the screen
shown in Figure 1, you may need to delete your temporary Internet files (basically flush the
cached web pages).
Figure 1 (Log-in screen)
4.2 Quick Start
The first screen (Figure 2) that appears (after the log in screen) is the Quick Start screen. By default
the Lynx L-210 has being configured to PPP connection and user would only need to enter the
username and password (as specified by the local ISP) to make connection to the internet.
The Quick Start page is meant for basic users whom only require easy and seamless connectivity to
the internet without worrying about any other advance configuration setting.
Important:
After clicking on Connect, please be sure to “Save Settings” to register the username / password or
any other changes.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2 (Quick Start page)
4.3 Setup (for advance user)
From this screen the user can setup the Lynx L-210 (configure the LAN and WAN connection(s),
configure the advanced configuration options within the Lynx L-210 (security, routing, and filtering),
access tools that are helpful for debug purposes, obtain the status of the modem, and view the
extensive online help.
To setup your Lynx L-210 with a basic configuration, select Setup. Figure 3 illustrates the setup
page. The page is broken into two subsections the WAN configuration and the LAN configuration.
Before configuring the Lynx L-210, there are several concepts that you should be familiar with on
how your new Lynx L-210 works. Please take a moment to familiarize yourself with these concepts,
as it should make the configuration much easier.
Figure 3 (Setup page)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3.1 Wide Area Network connection
On the other side of the Lynx L-210 is where your Wide Area Network (WAN) connection; also
referred to as a broadband connection. This WAN connection is different for every WAN supplier.
Most of the configuration you will perform will be in this area. Local Area Network Connection(s)
4.3.2 Local Area Network connection
On one side of your Lynx L-210, you have your own Local Area network (LAN) connections. This is
where you plug in your local computers to the Lynx L-210. The Lynx L-210 is normally configured to
automatically provide all the PC's on your network with Internet addresses.
4.4 Configuring the WAN
Before the gateway will pass any data between the LAN interface(s) and the WAN interface, the
WAN side of the modem must be configured. Depending upon your DSL service provider or your
ISP, you will need some (or all) of the information outlined below before you can properly configure
the WAN:
•
•
•
•
Your DSL line VPI and VCI
Your DSL encapsulation type and multiplexing
Your DSL training mode (default is MMODE)
For PPPoA or PPPoE users, you also need these values from your ISP:
o
Your username and password
• For RFC 1483 users, you may need these values from your ISP:
o
o
o
o
Your DSL fixed Internet IP address
Your Subnet Mask
Your Default Gateway
Your primary DNS IP address
Since multiple users can use the Lynx L-210, the Lynx L-210 can simultaneously support multiple
connection types; hence, the user must set up different profiles for each connection. The Lynx L-
210 supports the following protocols:
•
•
•
•
•
•
DHCP
RFC2364 / PPPoA
RFC2516 / PPPoE
Static
Bridged
RFC1577 / CLIP
4.4.1 New Connection
A new connection is basically a virtual connection. Your Lynx L-210 can support up to 8 different
(unique) virtual connections. If you have multiple different virtual connections, you may need to
utilize the static and dynamic routing capabilities of the modem to pass data correctly.
4.4.1.1 Bridged gateway profile and Connection
A pure bridged connection does not assign and IP address to the WAN interface. NAT and firewall
rules are not enabled. This connection method makes the Lynx L-210 act as a hub, and just
passes packets across the WAN interface to the LAN interface.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
To configure the Lynx L-210 as a bridge, click on Setup and then click on New Connection. The
default PPPoE connection setup is displayed. At the Type field select Bridge and the Bridge
connection setup page is displayed (see Figure 4). Give your Bridge connection a unique name;
the name must not have spaces and cannot begin with numbers. In this case the unique name is
called Bridge. Select the encapsulation type (LLC or VC); if you are not sure just use the default
mode. Select the VPI and VCI settings; your DSL service provider or your ISP will supply these; in
this case the DSL service provider is using 0,100. Also select the quality of service (QOS); leave
the default value if you are unsure or the ISP did not provide this information.
Figure 4 (Bridge Connection Setup)
To complete the connection you must now click the apply button. The apply button will temporarily
save this connection. To make the change permanent, you need to click on Save Settings. At the
system commands page, click on Save All.
4.4.1.2 PPPoA Connection Setup
PPPoA is also known as RFC 2364. It is a method of encapsulating PPP packets over ATM cells
which are carried over the DSL line. PPP or Point-to-Point protocol is a method of establishing a
network connection / session between network hosts. It usually provides a mechanism of
authenticating users. LLC and VC are two different methods of encapsulating the PPP packet.
Contact your ISP to make sure which encapsulation is being supported.
By selecting PPPoA, you are forcing your Lynx L-210 to terminate the PPPoA connection. The
advantage is that the PPPoA termination is done within the Lynx L-210 and not on your PC; this
frees up your PC resources and allows multiple users to utilize the PPPoA connection.
To configure the gateway for PPPoA, click on Setup and then click on New Connection. The
default PPPoE connection setup is displayed. At the Type field select PPPoA and the PPPoA
connection setup page is displayed; figure 5 illustrates a typical PPPoA configuration. Give your
PPPoA connection a unique name; the name must not have spaces and cannot begin with
numbers. In this case the unique name is called PPPoA1. Select the encapsulation type (LLC or
VC); if you are not sure just use the default mode. Select the VPI and VCI settings; your DSL
10
Download from Www.Somanuals.com. All Manuals Search And Download.
service provider or your ISP will supply these; in this case the DSL service provider is using 0,100.
Also select the quality of service (QOS); leave the default value if you are unsure or the ISP did not
provide this information.
Following is a description of the different options:
a. Username: The username for the PPPoA access; this is provided by your DSL service
provider or your ISP.
b. Password: The password for the PPPoA access; this is provided by your DSL service
provider or your ISP.
c. On-Demand: Enables on-demand mode. The connection will disconnect if no activity is
detected after the specified idle timeout value.
d. Idle Timeout: Specifies that PPPoA connection should disconnect if the link has no activity
detected for n seconds. This field is used in conjunction with the On-Demand feature. To
ensure that the link is always active, enter a 0 in this field.
e. Keep Alive: When on-demand option is not enable, this value specifies the time to wait
without being connected to your provider before terminating the connection. To ensure that
the link is always active, enter a 0 in this field.
f. Set Route: Specify this connection as the default-route.
g. MRU: Maximum Receive Unit the DSL connection can receive. It is a negotiated value that
asks the provider to send packets of no more than n bytes. The maximum specified value is
1500 although some DSL/ISP providers require a larger value. The minimum MRU value is
128.
Figure 5 (PPPoA Connection Setup)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
To complete the connection you must now click the apply button. The apply button will temporarily
save this connection. To make the change permanent you need to click on Save Setting (at the
side of the page). At the system commands page, click on Save All.
4.4.1.3 PPPoE Connection Setup
PPPoE is also known as RFC 2516. It is a method of encapsulating PPP packets over Ethernet.
PPP or Point-to-Point protocol is a method of establishing a network connection/session between
network hosts. It usually provides a mechanism of authenticating users.
To configure the gateway for PPPoE, click on Setup and then click on New Connection. The
default PPPoE connection setup is displayed. At the Type field select PPPoE and the PPPoE
connection setup page is displayed; figure 6 illustrates a typical PPPoE configuration. Give your
PPPoE connection a unique name; the name must not have spaces and cannot begin with
numbers. In this case the unique name is called PPPoE1. Select the encapsulation type (LLC or
VC); if you are not sure just use the default mode. Select the VPI and VCI settings; your DSL
service provider or your ISP will supply these; in this case the DSL service provider is using 0,100.
Also select the quality of service (QOS); leave the default value if you are unsure or the ISP did not
provide this information.
Following is a description of the different options:
a. Username: The username for the PPPoE access; this is provided by your DSL service
provider or your ISP.
b. Password: The password for the PPPoE access; this is provided by your DSL service
provider or your ISP.
c. On-Demand: Enables on-demand mode. The connection will disconnect if no activity is
detected after the specified idle timeout value.
d. Idle Timeout: Specifies that PPPoE connection should disconnect if the link has no activity
detected for n seconds. This field is used in conjunction with the On-Demand feature. To
ensure that the link is always active, enter a 0 in this field.
e. Keep Alive: When on-demand option is not enable, this value specifies the time to wait
without being connected to your provider before terminating the connection. To ensure that
the link is always active, enter a 0 in this field.
f. Set Route: Specify this connection as the default-route.
g. MRU: Maximum Receive Unit the DSL connection can receive. It is a negotiated value that
asks the provider to send packets of no more than n bytes. The maximum specified value is
1500 although some DSL/ISP providers require a larger value. The minimum MRU value is
128.
h. Enforce MRU: Check this box if you experience problems accessing the Internet over a
PPPoE connection. This feature will force all TCP traffic to conform with PPP MRU by
changing TCP Maximum Segment Size to PPP MRU.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 6 (PPPOE Connection Setup)
To complete the connection you must now click the apply button. The apply button will temporarily
save this connection. To make the change permanent you need to click on Save Setting (at the
side of the page). At the system commands page, click on Save All.
4.4.1.4 DHCP Connection Setup
Dynamic Host Configuration Protocol (DHCP) allows the Lynx L-210 to automatically obtain the IP
address from the server. This option is commonly used in situations where IP is dynamically
assigned and is not known prior to assignment.
To configure the Lynx L-210 for a DHCP connection, click on Setup and then click on New
Connection. The default DHCP connection setup is displayed. At the Type field select DHCP and
the DHCP connection setup page is displayed; figure 7 illustrates a typical DHCP configuration.
Give your DHCP connection a unique name; the name must not have spaces and cannot begin with
numbers. In this case the unique name is called DHCP1. Select the encapsulation type (LLC or
VC); if you are not sure just use the default mode. Select the VPI and VCI settings; your DSL
service provider or your ISP will supply these; in this case the DSL service provider is using 0,100.
Also select the quality of service (QOS); leave the default value if you are unsure or the ISP did not
provide this information.
If your DSL line is connected and your DSL/IPS provider is supporting DHCP, you can click the
renew button and the gateway will retrieve an IP address, Subnet mask, and Gateway address. At
anytime, you can renew the DHCP address by clicking on the renew button; in most cases you will
never have to use this button.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 7 (DHCP Connection Setup)
To complete the connection you must now click the apply button. The apply button will temporarily
save this connection. To make the change permanent you need to click on Save Settings (at the
side of the page). At the system commands page, click on Save All.
4.4.1.5 Static Connection Setup
Static is used whenever a known static IP is assigned. The accompanying information such as the
Subnet mask and the gateway should also be specified. Up to three Domain Name Server (DNS)
addresses can also be specified. These servers would enable you to have access to other web
servers. Valid IP addresses range is from 0.0.0.0 to 255.255.255.255.
To configure the Lynx L-210 for a Static connection, click on Setup and then click on New
Connection. The default Static connection setup is displayed. At the Type field select Static and
the Static connection setup page is displayed; figure 8 illustrates a typical Static configuration. Give
your Static connection a unique name; the name must not have spaces and cannot begin with
numbers. In this case the unique name is called STATIC1. Select the encapsulation type (LLC or
VC); if you are not sure just use the default mode. Select the VPI and VCI settings; your DSL
service provider or your ISP will supply these; in this case the DSL service provider is using 0,35.
Also select the quality of service (QOS); leave the default value if you are unsure or the ISP did not
provide this information. You can also enable Network Address Translation (NAT) and the Firewall
options. If you are unsure, leave these in the default mode.
Based upon the information your DSL/ISP provided, enter your assigned IP address, Subnet Mask,
Default Gateway (if provided), and Domain Name Services (DNS) values (if provided). For the
static configuration, you can also select a bridge connection or a routed connection. Since static IP
address is typically used to host WEB servers, you may want to use a bridge connection.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 8 (Static IP Connection Setup)
To complete the connection you must now click the apply button. The apply button will temporarily
save this connection. To make the change permanent you need to click on Save Settings (at the
side of the page). At the system commands page, click on Save All.
4.4.1.6 Classical IP over ATM (CLIP, defined in RFC1577) Connection Setup
The Classical IP over ATM (CLIP) support provides the ability to transmit IP packets over an ATM
network, CLIP support will encapsulate IP in an AAL5 packet data unit (PDU) frame using
RFC1577and it utilizes an ATM aware version of the ARP protocol (ATMARP. support only allows
for PVC support; it does not support SVC).
To configure the Lynx L-210 for a CLIP connection, click on Setup and then click on New
Connection. The default CLIP connection setup is displayed. At the Type field select CLIP and the
CLIP connection setup page is displayed; figure 9 illustrates a typical CLIP configuration. Give your
CLIP connection a unique name; the name must not have spaces and cannot begin with numbers.
In this case the unique name is called CLIP1. Select the VPI and VCI settings; your DSL service
provider or your ISP will supply these; in this case the DSL service provider is using 0,101. Also
select the quality of service (QOS); leave the default value if you are unsure or the ISP did not
provide this information. You can also enable Network Address Translation (NAT) and the Firewall
options. If you are unsure, leave these in the default mode.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 9 (CLIP Connection Setup)
To complete the connection you must now click the apply button. The apply button will temporarily
save this connection. To make the change permanent you need to click on Save Settings (at the
side of the page). At the system commands page, click on Save All.
4.4.2 Modify an Existing Connection
To modify an existing connection, click setup and then click the connection you want to modify. The
connections are listed as Connection 0 through Connection 7
As a note, if you delete the connection, to make the change permanent you need to click on Save
Settings (at the side of the page). At the system commands page, click on Save All.
4.4.3 Modem setup
To configure the DSL modulation type, Click setup. Under WAN Setup, select Modem Setup. This
will bring up the modem setup screen. Leave the default value if you are unsure or the DSL/ISP did
not provide this information. For most all cases, this screen should not be modified.
The apply button will temporarily save this connection. To make the change permanent you need to
click on Save Settings (at the side of the page). At the system commands page, click on Save All.
4.5 Configuring the LAN
By default, your Lynx L-210 has DHCP server (LAN side) enabled. If you already have a DHCP
server running on your network, you must disable one of the two DHCP servers; if you plug a
16
Download from Www.Somanuals.com. All Manuals Search And Download.
second DHCP server into the network, you will experience network errors and the network will not
function normally.
4.5.1 Enable/Disable DHCP
To enable or disable DHCP, Click setup. Under LAN Setup, select DHCP Configuration. This will
bring up the screen shown in Figure 10.
The Start IP Address is where the DHCP server starts issuing IP addresses. This value must be
greater than the Lynx L-210 IP address value. For example if the Lynx L-210 IP address is
192.168.1.1 (default) than the starting IP address must be 192.168.1. 2 (or higher).
The End IP Address is where the DHCP server stops issuing IP addresses. The ending address
cannot exceed a subnet limit of 254. Hence the max value for our default gateway is
192.168.1.254. If the DHCP server runs out of DHCP addresses, users will not get access to
network resources. If this happens you can increase the Ending IP address (to the limit of 255) or
reduce the lease time.
The Lease Time is the amount of time a network user will be allowed connection to the Lynx L-210
with their current dynamic IP address. The amount of time is in units of minutes; the default value is
3600 minutes (60 hours).
Note: If you change the start or end values, make sure the values are still within the same subnet
as the gateways IP address. In other words, if the gateways IP address is 192.168.1.1 (default)
and you change the DHCP start/end IP addresses to be 192.128.1.2/192.128.1.100, you will not be
able to communicate to the Lynx L-210 if your PC has DHCP enabled.
Figure 10 (DHCP Server configuration)
In addition to the DHCP server feature, the Lynx L-210 supports the DHCP relay function. When the
Lynx L-210 is configured as DHCP server, it assigns the IP addresses to the LAN clients. When the
Lynx L-210 is configured as DHCP relay, it is responsible for forwarding the requests and
responses negotiating between the DHCP clients and the server. See figure 11.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 11 (Example of a DHCP Relay configuration)
By turning off the DHCP server and relay the network administrator must carefully configure the IP
address, Subnet Mask and DNS settings of every computer on your network. Do not assign the
same IP address to more than one computer and your Lynx L-210 must be on the same subnet as
all the other computers.
The apply button will temporarily save this connection. To make the change permanent you need to
click on Save Settings (at the side of the page). At the system commands page, click on Save All.
4.5.2 Changing the Lynx L-210 IP address
You can change the Lynx L-210’s IP address by, clicking Setup and under LAN Setup, select
Management. This will bring up the screen shown in Figure 12.
4.5.2.1 Static IP address assignment
Your Lynx L-210’s default IP address and subnet mask are 192.168.1.1/255.255.255.0; this subnet
mask will allow the Lynx L-210 to support 254 users. If you want to support a larger number of
users you can change the subnet mask; but remember. The DHCP server is defaulted to only give
out 255 IP addresses. Further remember that if you change your gateways’ IP address and you
have DHCP enabled, the DHCP configuration must reside within the same subnet
The default gateway is the routing device used to forward all traffic that is not addressed to a station
within the local subnet. Your ISP will provide you with the default gateway Address. Figure 12
shows a default gateway address of 203.125.64.1 because this was the default gateway defined
when the CLIP connection was configured.
The hostname can be any alphanumeric word that does not contain spaces. The domain name is
used to in conjunction with the host name to uniquely identify the gateway. To access the Lynx L-
210’s web pages the user can type 192.168.1.1 (the default IP address) or type mygateway.ar7.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 12 (Management IP address)
The apply button will temporarily save this connection. To make the change permanent you need to
click on Save Settings (at the side of the page). At the system commands page, click on Save All.
4.5.3 Firewall/NAT Services
You can enable or disable Firewall and NAT by clicking on Setup and under LAN Setup, select
Firewall/NAT Services. By unselecting the “Enable Firewall and NAT Services” button the firewall
and NAT services is disabled for all WAN connections.
The apply button will temporarily save this connection. To make the change permanent you need to
click on Save Settings (at the side of the page). At the system commands page, click on Save All.
4.6 Advanced (for advance user only)
The Lynx L-210 supports a host of advanced features. For basic Lynx L-210 functionality, the user
does not need to utilize these advanced features. The features help with routing, security, port
configuration, and plug and play capability.
4.6.1 UPnP
UPnP NAT and Firewall Traversal allow traffic to pass-thru the Lynx L-210 for applications using the
UPnP protocol. This feature requires one active DSL connection. In presence of multiple DSL
connections, select the one over which the incoming traffic will be present, for example the default
Internet connection.
To enable UPnP, you must first have a WAN connection configured. Once a WAN connection is
configured, click Advanced and under Advanced, select UPnP. This will bring up the screen shown
in Figure 13. You must enable UPnP and then select which connection will utilize UPnP. In this
case the PPPoA connection is enabled.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 13 (Management IP address)
The apply button will temporarily save this connection. To make the change permanent you need to
click on Save Settings (at the side of the page). At the system commands page, click on Save All.
4.6.2 Port Forwarding
Using the Port Forwarding page, you can provide local services (for example web hosting) for
people on the Internet or play Internet games. When users send this type of request to your network
via the Internet, the Lynx L-210 will forward those requests to the appropriate PC. Port forwarding
can be used with DHCP assigned addresses but remember that a DHCP address is dynamic (not
static). For example, if you were configuring a Netmeeting server, you would want to assign this
server a static IP address so that the IP address is not reassigned. Also remember that if an
Internet user is trying to access an Internet application, they must use the WAN IP address. The
port forwarding will translate the WAN IP address into a LAN IP address.
To configure a service, game, or other application select the external connection (for example the
Internet connection), from the Home screen, click Advanced and under Advanced, select Port
Forwarding. Next select the computer hosting the service and add the corresponding firewall rule. If
you want to add a custom application, select the User category, click New and fill in the port,
protocols and description for your application.
For example, if you want to host a Netmeeting session, from the Home screen, click Advanced and
under Advanced, select Port Forwarding. First select the IP address for your Netmeeting server.
Next select the Audio/Video category and add Netmeeting to the applied rules box. To view the
management rules, highlight Netmeeting and select view; this will display the pre configured
protocols and ports that Netmeeting will use. Now assuming that your WAN connection is correct,
you can run Netmeeting from your server and call users that are on the Internet. If you know your
WAN IP address, users can call you.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 13 (Port Forwarding: Netmeeting)
The apply button will temporarily save this connection. To make the change permanent you need to
click on Save Settings (at the side of the page). At the system commands page, click on Save All.
4.6.3 Advanced Security
In the presence of the firewall, anonymous Internet traffic is blocked. Using the advanced security
features, you can redirect this traffic to a dedicated computer on your local network (DMZ) or open
the access from the Internet to the Lynx L-210's management ports (web, telnet). The Lynx L-210's
firewall and NAT services (port forwarding, access control) can be disabled for all interfaces by un-
checking the "Enable Firewall and NAT Service"
To enable any of the advanced security features, click Advanced and configure the option under
Firewall. Figure 14 illustrates the typical advanced security in Access Control configuration.
Figure 14 (Access Control)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
The apply button will temporarily save this connection. To make the change permanent you need to
click on Save Settings (at the side of the page). At the system commands page, click on Save All.
4.6.3.1 DMZ configuration
Setting a computer (on your local network) as a DMZ forwards any network traffic that is not
redirected to another computer via the port-forwarding feature to the computer's IP address. This
opens the access to the DMZ computer from the Internet.
4.6.3.2 Enable Web from WAN
Enabling the Web from WAN on your local network allows Web requests that come from the
Internet to be re-routed to a Web Server that is on a different subnet. This is different that the Web
server rule that is configurable via the port-forwarding page. In this case, the web server is on a
different subnet.
4.6.3.3 Enable Remote Telnet
Enabling the Remote Web on your local network allows telnet requests that come from the Internet
to be re-routed to a telnet Server that is on a different LAN IP subnet. This is different that the
telnet server rule that is configurable via the port-forwarding page. In this case, the telnet server is
on a different subnet.
4.6.3.4 Enable Incoming ICMP Ping
Enabling the Incoming Internet Control Message Protocol (ICMP) Ping will allow Echo requests to
come into the gateway. The gateway will respond with an ICMP Echo response message. The
option allows the DSL provider or ISP to determine the following:
a. The status of the network.
b. Tracking and isolating hardware and software problems.
c. Testing, measuring, and managing networks.
4.6.4 Access Control
Access control can also be called port blocking. Specific types of traffic that is destined to a
selected LAN IP address can be blocked. To enable any of the Access Control features, click
Advanced and under Advanced, select Access Control. A page similar to the port-forwarding page
appears. Similar to the port-forwarding page, an IP address can be added to a rule. All Access
Control rules have precedence over rules that were added via the port-forwarding page.
The apply button will temporarily save this connection. To make the change permanent you need to
click on Save Settings (at the side of the page). At the system commands page, click on Save All.
4.6.5 LAN clients
To add a LAN client, click Advanced and under Advanced, select LAN Clients. If DHCP is used, all
DHCP clients are automatically assigned. If a fixed IP address server is on the LAN and you want
this server to be visible via the WAN, you must add its IP address. Once the IP address has been
added to you can apply Port Forwarding and Access Control rules to this IP address.
The apply button will temporarily save this connection. To make the change permanent you need to
click on Save Settings (at the side of the page). At the system commands page, click on Save All.
4.6.6 MAC Address Filters
The MAC filtering mechanism provides a way for the users to define rules to allow/deny frames
22
Download from Www.Somanuals.com. All Manuals Search And Download.
through the bridge based on source MAC address, destination MAC address and/or frame type.
When bridge filtering is enabled, each frame is examined against the defined filter rules
sequentially, and when a matched is determined, the appropriate filtering action (determined by the
access type selected ... i.e. allow or deny) is performed. The user should note that the MAC filter
will only examined frames from interfaces that are part of the bridge itself. Twenty filter rules are
supported with MAC filtering. To enable MAC Filters, click Advanced and under Advanced, select
MAC
Filters.
Figure
15
illustrates
a
typical
Bridge
filter
configuration.
The User Interface for MAC Filter allows the user to add/edit/delete, as well as, enables the filter
rules. To add rules, simply define the source MAC address, destination MAC address and frame
type with desired filtering type (i.e. allow/deny), and press the “Add” button. The MAC address must
be in a xx-xx-xx-xx-xx-xx format, with 00-00-00-00-00-00 as “don’t care”. Blanks can be used in the
MAC
address
space,
and
would
be
considered
also
as
“don’t
care”.
To edit/modify an existing filter rule, select the desired rule created previously from “Add” in the
“Edit” select box. The selected filter rule will appear on top section, as with the “Add” filter rule.
Make the desired change to the MAC address, frame type and/or access type, and press “Apply”.
To delete filter rule(s), select the filter rule entry to delete in the “Delete” selection box. Note that
multiple deletions are possible. Once all the desired filter rule(s) is/are selected for deletion, press
the “Apply” button. The “Select All” select box can also be used to delete the entire filter rule. It
provides
a
quick
method
of
selecting
all
filter
rules
for
deletion.
The “Enable MAC Filters” button allow the user to enable or disable MAC filtering. It can be
set/unset during any add/edit/delete operation. It can also be set/unset independently by just
pressing the “Apply” button.
Figure 15 (MAC Filters)
Note: The MAC filter table contains 3 hidden rules. These rules are entered automatically by the
system to ensure the user does not "lock" them out of the system. The first rule allows any and all
23
Download from Www.Somanuals.com. All Manuals Search And Download.
ARP frames through the system. The second rule allows all IPv4 frames with the destination MAC
address of the bridge to go through. The third rule allows all IPv4 frames with the source MAC
address of the bridge to go through.
Note: On a windows based machine, to find a MAC address, at a dos prompt type ipconfig /all.
The apply button will temporarily save this connection. To make the change permanent you need to
click on Save Settings (at the side of the page). At the system commands page, click on Save All.
4.6.7 Multicast
Multicasting is a form of limited broadcast. UDP is used to send datagrams to all hosts that belong
to what is called a "host group." A host group is a set of zero or more hosts identified by the same
destination IP address. The following statements apply to host groups.
a. Anyone can join or leave a host group at will.
b. There are no restrictions on a host's location.
c. There are no restrictions on the number of members that may belong to a host group.
d. A host may belong to multiple host groups.
e. Non-group members may send UDP datagrams to the host group.
Multicasting is useful when data needs to be sent to more than one other device. For instance, if
one device is responsible for acquiring data that many other devices need, then multicasting is a
natural fit. Note that using multicasting as opposed to sending the same data to individual devices
uses less network bandwidth.
To enable Multicasting, click on Advanced and under Advanced, select Muliticast. Figure 16
illustrates a typical Multicast configuration.
Figure 16 (Multicast)
The apply button will temporarily save this connection. To make the change permanent you need to
click on Save Settings (at the side of the page). At the system commands page, click on Save All.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
4.6.8 Static Routing
If the Lynx L-210 is connected to more than one network, you may need to set up a static route
between them. A static route is a pre-defined pathway that network information must travel to reach
a specific host or network. You can use static routing to allow different IP domain users to access
the Internet through the Lynx L-210.
The New Destination IP is the address of the remote LAN network or host to which you want to
assign a static route. Enter the IP address of the host for which you wish to create a static route
here. For a standard Class C IP domain, the network address is the first three fields of the New
Destination IP, while the last field should be 0. The Subnet Mask identifies which portion of an IP
address is the network portion, and which portion is the host portion. For a full Class C Subnet, the
Subnet Mask is 255.255.255.0. The Gateway IP address should be the IP address of the gateway
device that allows for contact between the Gateway and the remote network or host. The Hop
Count determines the maximum number of steps between network nodes that data packets will
travel. A node is any device on the network (such as a router or switch)
To enable Static Routing, from the Home screen, click Advanced and under Advanced, select Static
Routing. Figure 17 illustrates a typical Static Route.
Figure 17 (Static Routing)
The apply button will temporarily save this connection. To make the change permanent you need to
click on Save Settings (at the side of the page). At the system commands page, click on Save All.
4.6.9 Dynamic Routing
Dynamic Routing allows the Lynx L-210 to automatically adjust to physical changes in the network.
The Lynx L-210, using the RIP protocol, determines the network packets’ route based on the fewest
number of hops between the source and the destination. The RIP protocol regularly broadcasts
routing information to other Lynx L-210s on the network.
The Direction determines the direction that RIP routes will be updated. Selecting In means that the
Lynx L-210 will only incorporate received RIP information. Selecting Out means that the Lynx L-210
25
Download from Www.Somanuals.com. All Manuals Search And Download.
will only send out RIP information. Selecting both means that the Lynx L-210 will incorporate
received RIP information and send out updated RIP information.
The protocol is dependent upon the entire network. Most networks support Rip v1. If RIP v1 is
selected, routing data will be sent in RIP v1 format. If Rip V2 is selected, routing data will be sent in
RIP v2 format using subnet broadcasting. If Rip V1 Compatible is selected, routing data will be sent
in RIP v2 format using multicasting.
To enable Dynamic Routing, click Advanced and under Advanced, select Dynamic Routing. Figure
18 illustrates a typical Dynamic Route.
Figure 18 (Dynamic Routing)
The apply button will temporarily save this connection. To make the change permanent you need to
click on Save Settings (at the side of the page). At the system commands page, click on Save All.
4.7 Tools
The Lynx L-210 supports a host of tools that will allow you to customize and debug your Lynx L-
210.
4.7.1 System Commands
To make the changes permanent you need to click on Tools (at the top of the page) and select
System Commands. The following commands are used to configure the gateway:
a.
b.
c.
Save all: Press this button in order to permanently save the current configuration of the
Lynx L-210. If you do re-start the system without saving your configuration, the Lynx L-
210 will revert back to the previously saved configuration.
Restart: Use this button to re-start the system. If you have not saved your configurations,
the Lynx L-210 will revert back to the previously saved configuration upon re-starting.
NOTE: Connectivity to the unit will be lost. You can reconnect after the unit reboots.
Restore Defaults: Use this button to restore factory default configuration.
NOTE: Connectivity to the unit will be lost. You can reconnect after the unit reboots.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
4.7.2 User Management
You can change your Lynx L-210’s username and password by clicking on User Management.
From here you can change the login name and password. You can also change the idle timeout;
you will need to log back onto the Lynx L-210 once the timeout expires.
If you forget your password, you can press and hold the reset to factory defaults button for 10
seconds (or more). The Lynx L-210 will reset to its factory default configuration and all custom
configurations will be lost.
The apply button will temporarily save this connection. To make the change permanent you need to
click on Save Settings (at the side of the page). At the system commands page, click on Save All.
4.7.3 Update Firmware
You can remotely upgrade the Lynx L-210’s firmware, clicking on Update Firmware under the Tools
page. This will bring up the screen shown in Figure 19. The upgrade file shall be in *.img format.
To upgrade the firmware, click browse, find the firmware file to download. Make sure this is the
correct file. Click on upgrade firmware (as shown in Figure 19). Once the upgrade is complete the
Lynx L-210 will reboot. You will need to log back onto the Lynx L-210 after the firmware upgrade is
completed.
The firmware upgrade should take about 5 minutes to complete.
Note: Do not remove power from the Lynx L-210 during the firmware upgrade procedure.
Figure 19 (Update Firmware)
4.7.4 Ping Test
Once you have your Lynx L-210 configured, it is a good idea to make sure you can ping the
network. You can get to the Ping page under the Tools title, by clicking on Ping Test. Type the
target address that you want to ping. If you have your PC connected to the Lynx L-210 via the
27
Download from Www.Somanuals.com. All Manuals Search And Download.
default DHCP configuration, you should be able to Ping the network address 192.168.1.1. If your
ISP has provided their server address you can try to ping the address. If the pings for both the
WAN and the LAN side complete, and you have the proper protocols configured, you should be
able to surf the Internet.
By default when you select ping test, the Lynx L-210 will ping itself 3 times. As shown in Figure 20,
the Lynx L-210 passed the Ping test; this basically means that the TCP/IP protocol is up and
running. If this first Ping test does not pass, the TCP/IP protocol is not loaded for some reason; you
should restart the Lynx L-210.
Figure 20 (Ping test)
4.7.5 Modem Test
The Modem Test is used to check whether your Lynx L-210 is properly connected to the WAN
Network. This test may take a few seconds to complete. To perform the test, select your connection
from the list and press the Test button. Before running this test, make sure you have a valid DSL
link; if the DSL link is not connected, this test will always fail.
Also the DSLAM must support this feature; not all DSLAMs have F4 and F5 support.
4.8 Status
The Status section allows you to view the Status/Statistics of different connections and interfaces
4.8.1 Network Statistics
Select to view the Statistics of different interfaces - Ethernet/USB/DSL.
4.8.2 Connection Status
Select to view the Status of different connections.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
4.8.3 DHCP Clients
Select to view the list of DHCP clients.
4.8.4 Modem Status
Select to view the Status and Statistics of your broadband (DSL) connection.
4.8.5 Product Information
You can display the Lynx L-210’s driver and run-time information by going under Status title and
click on Product Information. Figure 21 illustrates the typical product information, which is provided.
Figure 21 (Product Information)
4.8.6 System Log
You can display the Lynx L-210’s log by going under the Status title, click System log. From here
you can view all logged information. Depending upon the severity level, this logged info will
generate log reports to a remote host (if remote logging is enabled).
29
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Appendix A: Troubleshooting
Below is a list of commonly asked questions. Before calling technical support, please look through
these issues to see if they help to solve your problem.
5.1 The Lynx L-210 is not functional
1. Check to see that the power LED is green and than the network cables are installed
correctly. Refer to the easy start guide for more details.
2. Check to see that the ETH/LAN and PPP/WAN LEDs are green.
3. Check to see that the DSL LED is green
4. Make sure you are not connecting the USB and the Ethernet port at the same time. You
must only use 1 interface at a time.
5. Check the settings on your PC. Again, refer to the easy start guide for more details
6. Check the Lynx L-210’s settings.
7. From your PC, can you PING the Lynx L-210? Assuming that the Lynx L-210 has DHCP
enabled and your PC is on the same subnet as the gateway, you should be able to PING
the gateway.
8. Can you PING the WAN IP? Your ISP should have provided the IP address of their server.
If you can ping the Lynx L-210 and your protocols are configured correctly, you should be
able to ping the ISPs network. If you cannot PING the ISPs network, make sure you are
using the correct protocols with the correct VPI/VCI values.
9. Make sure NAT is enabled for your connection. If NAT is disabled the Lynx L-210 will not
route frames correctly (except in Bridge connection).
5.2 I can’t connect to the Lynx L-210
1. Check to see that the power LED is green and that the network cables are installed
correctly; see the easy start guide for more details.
2. Make sure you are not connecting the USB and the Ethernet port at the same time. You
must only use 1 interface at a time.
3. Make sure that your PC and the Lynx L-210 is on the same network segment. The Lynx L-
210’s default IP address is 192.168.1.1. If you are running a Windows based PC, you can
open a DOS window and type IPCONFIG; make sure that the network adapter that is
connected to the gateway is within the same 192.168.1.x subnet.
4. Also, your PC’s Subnet Mask should match the gateways subnet mask. The gateway has a
default subnet mask of 255.255.255.0.
5. If this still does not work, press the reset button for 10 seconds. This will place the gateway
into its factory default state. Go through the above procedures again.
6. Make sure NAT is enabled for your connection. If NAT is disabled the Lynx L-210 will not
route frames correctly (except in Bridge connection).
5.3 The DSL Link LED continues to blink but does not go solid
1. This means that the DSL line is trying to train but for some reason it cannot establish a valid
connection. The main cause of this is that you are too far away from the central office.
Contact your DSL service provider for further assistance.
2. Verify that the phone line is connected directly to the wall and to the line input on the Lynx L-
210.
3. Make sure that for every parallel phone line connected to telephone or fax to install with a
micro filter.
Common Problems and Solutions
30
Download from Www.Somanuals.com. All Manuals Search And Download.
5.4 The DSL Link LED is always off
1. Make sure you have DSL service. You should get some kind of information from your ISP
that states that DSL service is installed. You can usually tell if the service is installed by
listening to the phone line; you will hear some high-pitched noise. If you do not hear high-
pitched noise, contact your ISP.
2. Verify that the phone line is connected directly to the wall and to the line input on the Lynx L-
210. If the phone line is connected to the phone side of the Lynx L-210 or you have a splitter
installed on the phone line, the DSL light will not come on.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
Lynx L-210 terms
What is a firewall?
A firewall is protection between the Internet and your local network. It acts similarly to the firewall in
your car, protecting the interior of the car from the engine. Your car's firewall has very small opening
that allow desired connections from the engine into the cabin (gas pedal connection, etc), but if
something happens to your engine, you are protected.
The firewall in the Lynx L-210 is very similar. Only the desired connections that you allow are
passed through the firewall. These connections are normally originating from the local network;
such as web browsing, checking your email, downloading a file, and playing a game. However, in
some cases, you can allow incoming connections so that you can run programs like a web server.
What is NAT?
NAT stands for Network Address Translation. Another name for it is Connection Sharing. What
does this mean? Your ISP provides you with a single network address for you to access the Internet
through. However, you may have several machines on your local network that want to access the
Internet at the same time. The Lynx L-210 provides NAT functionality that converts your local
network addresses to the single network address provided by your ISP. It keeps track of all these
connections and makes sure that the correct information gets to the correct local machine.
Occasionally, there are certain programs that don't work well through NAT. Some games, and some
specialty applications have a bit of trouble. The Lynx L-210 contains special functionality to handle
the vast majority of these troublesome programs and games. NAT does cause problems when you
want to run a SERVER though. When running a server, please see the DMZ section below.
What is a DMZ?
DMZ really stands for Demilitarized Zone. It is a way of separating out part of your local network so
that is more open to the Internet. Suppose that you want to run a web-server, or a game server.
Normal servers like these are blocked from working by the NAT functionality. The solution is to
"isolate" the single local computer into a DMZ. This makes the single computer look like it is directly
on the Internet, and others can access this machine.
Your machine isn't really directly connected to the Internet, and it really has an internal local
network address. When you provide the servers network address to others, you must provide the
address of the Lynx L-210. The Lynx L-210 "fakes" the connection to your machine.
You should use the DMZ when you want to run a server that others will access from the Internet.
Internal programs and servers (like print servers, etc) should NOT be connected to the DMZ
What is a Gateway?
The Internet is so large that a single network cannot handle all of the traffic and still deliver a
reasonable level of service. To overcome this limitation, the network is broken down into smaller
segments or subnets that can deliver good performance for the stations attached to that segment.
This segmentation solves the problem of supporting a large number of stations, but introduces the
problem of getting traffic from one subnet to another.
To accomplish this, devices called routers or gateways are placed between segments. If a machine
wishes to contact another device on the same segment, it transmits to that station directly using a
simple discovery technique. If the target station does not exist on the same segment as the source
station, then the source actually has no idea how to get to the target.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
One of the configuration parameters transmitted to each network device is its default gateway. This
address is configured by the network administrators and it informs each personal computer or other
network device where to send data if the target station does not reside on the same subnet as the
source. If your machine can reach all stations on the same subnet (usually a building or a sector
within a building), but cannot communicate outside of this area, it is usually because of an
incorrectly configured default gateway.
Lynx: constellation introduced by J. Hevelius in 1687. The Lynx is a
nocturnal wildcat with superb eyesight. The observers of this constellation
would have to be “lynx-eyed” to see it.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
|