D315M
ORDERCODE 100100
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Safety
These safety precautions include information to prevent personal injury and damage to the
projector.
Safety Definitions
WARNING:
Statements identify conditions or practices that could result in personal injury.
CAUTION:
Statements identify conditions or practices that could result in damage to your
equipment.
Projector Safety
WARNING:
•
•
•
Please use the power cord provided. Connect the power cord to a receptacle with a
protective safety (earth) ground terminal.
Don’t look directly into the lens when the lamp is on. Doing so may cause eye
injury.
Servicing your own projector may expose you to hazards or create potential
hazards. Also, servicing your own projector will void the warranty. Refer all
service to qualified service personnel.
•
Do not loosen or remove any screws other than those on the lamp module cover
and the lamp module. Doing so may result in electric shock.
For information about use of a feature, please refer to this User Guide.
Hot surface. Do not touch.
•
•
CAUTION:
•
Proper ventilation is important. Don’t block ventilation openings. Never operate
this projector in an enclosed area. Do not place the projector on a tablecloth or
other soft covering that may block the vents. With ceiling installations, use
approved mounting hardware. Do not put the projector near heaters, air cleaners,
transformers or other electrical devices. For permanent installations follow local
codes.
•
•
•
Don’t set liquids on the projector. Spilled liquids may damage your projector.
Don’t put the projector on a hot surface or in direct sunlight.
Do not drop the projector.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Lamp Safety
WARNING:
•
To replace the lamp, turn off the power and unplug the power cord. To avoid burns,
wait 45 minutes before opening the lamp door. Follow all instructions provided in
this User’s Guide. See “Changing the Lamp Module” on page 35.
When you open the lamp module door, be careful not to touch the hot surfaces
inside.
In the unlikely event of the bulb rupturing, thoroughly clean the area behind the
projector and discard any items that might have been contaminated with broken
glass.
•
•
CAUTION:
•
•
•
Never operate your projector without the lamp module or lamp module door.
Doing so may damage the projector.
Do not touch the glass portion of the new lamp module with your hands or allow it
to touch other objects as this may damage it and shorten its operational life.
Do not drop the lamp module as the glass may shatter.
Battery Safety
Read and follow all warnings and instructions supplied by the battery manufacturer.
WARNING: Keep batteries away from children.
CAUTION:
•
•
•
•
•
Store batteries in their original packaging.
When inserting batteries, verify that the (+) and (-) terminals are aligned correctly.
Replace all batteries of a set at the same time.
Do not mix new batteries with used ones.
Do not use batteries of different chemistries, capacities, brands or sizes together.
Leakage could result.
•
•
•
Do not disassemble, recharge, or short-circuit batteries.
Do not subject batteries to high temperature or fire.
Discard used batteries according to all applicable local and national regulations.
Laser Safety
WARNING:
To reduce the risk of injury to the eyes, do not look directly into the laser light emitted from
the aperture on the Remote Control and do not point the laser light into anyone’s eyes. This
remote control is equipped with a Class IIIA laser that emits radiation.
NOTE:
Do not leave the remote control close to the cooling fan outlet of the projector.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Canada
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Safety Certifications
UL, CUL, TUV
EN 55022 Warning
This is a Class B product. In a domestic environment it may cause radio interference, in
which case the user may be required to take adequate measures. The typical use is in a
conference room, meeting room or auditorium.
Declaration of Conformity
We declare under our sole responsibility that the DLP Zoom Digital
Projector conforms to the following directives and norms:
Directive 89/336/EEC, Amended by 93/68/EEC
EMI: EN 55022 (1992) Class B
EMC: EN 50082-1 (1992)
EMC: EN 55024 : 1998
IEC61000-4-2, IEC61000-4-3, IEC61000-4-4, IEC61000-4-5,
IEC61000-4-6,IEC61000-4-11
Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000, IEC 60950 Third edition, UL 60950 Third edition
Apr. 2001
Taiwan BSMI.
Disclaimer: The manufactory or reseller shall not be reliable for technical or editorial errors
or omissions contained herein; nor or incidental or consequential damages resulting from
furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, the manufactory or reseller reserves the
right to change product specifications without notice. Information in this document may
change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any
purpose without prior written permission from copy owners.
© Copyright Dec. 2002. All rights reserved
4
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Table of Contents
Safety .......................................................................................................... 2
Safety Definitions.............................................................................................................2
Projector Safety................................................................................................................2
Lamp Safety .....................................................................................................................3
Battery Safety...................................................................................................................3
Laser Safety......................................................................................................................3
Preface ........................................................................................................ 7
Package Contents ....................................................................................... 7
Optional Accessories ................................................................................... 7
Accessories Overview.................................................................................. 8
Power Cord.......................................................................................................................8
Computer and Video Cables............................................................................................8
Others ...............................................................................................................................8
Product Profile ............................................................................................. 9
Front View........................................................................................................................9
Rear View.........................................................................................................................9
Bottom Panel....................................................................................................................9
LED Indicator & Control Pad on Projector...................................................................10
LED Indicators Message.....................................................................................10
Control Pad Function ..........................................................................................10
Remote Control Instruction............................................................................................11
Installation Steps ....................................................................................... 13
Getting Started ...............................................................................................................13
Connecting the Projector................................................................................................13
Connecting Input and Output Devices...........................................................................14
Starting the Projector .....................................................................................................15
Power on..............................................................................................................15
Turn on the source...............................................................................................15
Adjustment .....................................................................................................................16
Adjusting Projector Angle...................................................................................16
Adjusting the Zoom and Focus...........................................................................16
Adjusting the Keystone Control..........................................................................17
Adjusting the Zoom and Pan...............................................................................17
Power Off .......................................................................................................................18
Restart.............................................................................................................................18
On-Screen-Display Menu Format and Description..................................... 19
Input Source OSD ..........................................................................................................19
Ezkey OSD.....................................................................................................................20
Remote Control Buttons OSD .......................................................................................20
OSD Menu......................................................................................................................21
Main Menu ..........................................................................................................21
Setup Menu..........................................................................................................22
Color Manager Menu ..........................................................................................23
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Language Menu...................................................................................................24
Utilities Menu......................................................................................................25
Status Menu.........................................................................................................26
Reference.................................................................................................. 27
Positioning the Projector................................................................................................27
Remote Control Transmission Range............................................................................29
Product Specification .....................................................................................................30
Timing Charts.................................................................................................................31
Troubleshooting .............................................................................................................32
Power Indicator ...................................................................................................32
Remote Control ...................................................................................................32
Sound...................................................................................................................32
Image Source.......................................................................................................33
Image Quality ......................................................................................................33
Lamp....................................................................................................................34
Maintenance ...................................................................................................................35
Changing the Lamp .............................................................................................35
Changing the Battery of Remote Control ...........................................................36
Cleaning..........................................................................................................................37
Cleaning the Projection Lens ..............................................................................37
Cleaning Exterior Case........................................................................................37
Cleaning the Projector.........................................................................................37
Customer Support...................................................................................... 38
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector Quick Start Guide
Preface
Congratulations on purchasing a DLP™ (Digital Light Processing) projector.
The micro portable projector uses the Digital Light Processing (DLP™) technology along
with a built-in image manager. DLP ™ technology by Texas Instruments offers crystal clear
images with superior quality. A built-in image manager provides alternative settings for users
to optimize image quality. In addition, easy-to-use enhanced features, such as digital zoom,
keystone correction, wide-angle image and picture in picture, offer the users with versatility
and control functions.
In only minutes you can have your DLP Digital Projector ready to go. Just simply connect
the projector to an image source, Computer, DVD, VCR, or HDTV.
Package Contents
Make sure that all of the following components are included in the package. If anything is
missing, please contact your dealer immediately.
•
•
DLP Projector with lens cap
Standard Accessories:
- Power Cord
- Remote Mouse Cable with USB Connector
- S-Video Cable
- Computer Cable: DVI to D-Sub 15 pin VGA Cable
- Audio Cable: Stereo Min Jack to RCAx2 (Red & White)
- Remote Control, including two AAA Batteries
- Wizard CD, including User’s Guide in PDF format
- Quick Start Guide
- Carrying Case
Optional Accessories
The following cables are not standard accessories of this package. You are suggested to
contact your dealer whenever you need.
•
•
•
•
Composite Video Cable
Component Video Cable: DVI-I to HDTV
Audio Cable: Stereo to Stereo
DVI Cable: DVI to DVI signal cable for computer with DVI graphics card
□ Save the original box and all packing materials for
further shipping needs.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Accessories Overview
Power Cord
There are four different power cords for options, US type, UK type, Euro type and China
type. The appropriate Power Cord is included according to your geographical location &
safety requirement. If the standard kit does not satisfy your needs, then please contact your
dealer for further service.
Power Cord
(US type)
Power Cord
(UK type)
Power Cord
(Euro type)
Power Cord
(China type)
Computer and Video Cables
Computer Cable
DVI-I to DB-15 pin
VGA )
Remote Mouse Cable
with USB Connector
S-Video Cable
Audio Cable
Stereo Mini Jack to
RCAx2
Component Video
Cable (DVI-I to
HDTV)
Composite Video
Cable
DVI-DVI signal cable
(for computer with
DVI graphic cards)
Audio Cable
Stereo to Stereo
Others
Carrying Case
Remote Control with 2
AAA Batteries
Wizard CD
Quick Start Guide
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Product Profile
Front View
Speaker
Control Pad
Zoom Ring
Ventilation Hole
Focus Ring
Lens Cover
IR Sensor
Adjuster Foot
Rear View
I/O Connectors
Kensington Security
Lock
AC IN Socket
Bottom Panel
Fan Cover
Lamp Cover
ID Label
Ceiling Mounted
Screw
NOTE:
•
With ceiling installations, use approved mounting hardware & M4 screw.
Min. distance from ceiling/wall: 30/50 cm, 12/20 inch for proper ventilation. For
permanent installations, follow local codes.
•
The security lock corresponds to Kensington’s MicroSaver Security System. If you
have any comment, contact : Kensington, 2853 Campus Drive, San Mateo,
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
LED Indicator & Control Pad on Projector
Source Button (+)
EZKEY
Same as Source button
on the remote control
with function of
Keystone, Volume,
Frequency, and
Brightness for quick
selection.
Auto (-)
Same as Auto button
on the remote control
Power Button
Same as Power button
on the remote control
Lamp Ready LED
Indicator
Power LED Indicator
LED Indicators Message
Power LED Indicator
Green Color
Lamp Ready LED Indicator
Orange Color
Status
Plug in Power Cord
Steady light
Steady light
Power on without source
Power on with active source
Power off in cooling stage
System warming up
Blinking light
Steady light
Steady light
Flashing light
Light off
Light off
Flashing light
Light off
Control Pad Function
Description
Power
Function
Power on / off
EZ Key
Quick adjustment on Keystone, Frequency, Volume, and Brightness
by repeatedly pressing to scroll through these functions.
Source (+)
Auto (-)
Input Source selection,
(+) to perform adjustment increasingly in EZ-Key function
Auto Image
(-)to perform adjustment decreasingly in EZ Key function
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Remote Control Instruction
Laser aperture
(pointer/beam)
Power LED
Power ON/OFF
Laser pointer ON
Mouse cursor
Up direction
Left mouse button
Right mouse button
Enter button
Left direction
Down direction
Keystone correction
Right direction button
Volume (+/-)
Setup menu
Auto sync
Mute sound
Zoom (+)
Video source: ie,
Zoom (-)
composite or component
Blank screen
Freeze screen
Status of video information:
ie, resolution, frequency.
WARNING:
To reduce the risk of injury to the eyes, do not look directly into the
laser light emitted from the aperture on the Remote Control and do not
point the laser light into anyone’s eyes. This remote control is equipped
with a Class IIIA laser that emits radiation.
NOTE:
Do not leave the remote control close to the cooling fan outlet of the
projector.
For the information of remote control transmission range, please refer
page 29.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
The following buttons are located on the projector Control Pad
or on the Remote Control
Power Button
Switch power on or off.
Use the Power button to begin the warm-up period. The power
light blinks green during warm-up and stays green when the
projector is ready to use.
Menu Button
Use to display the On-Screen-Display Menus, which provide
several options for adjusting the projected image.
Auto Button
Source Button
Status Button
L Button
Use to auto adjust the image quality.
Use to select input source.
Use to get projector’s operation status information
Use as the left mouse cursor.
R Button
Use as the right mouse cursor.
Press to enter function.
↵ Button
4 Directional
Use to select or adjust control items.
Selection Buttons
Laser Pointer Button
Use instead of a pointer to activate the laser pointer for use in
presentations.
Volume +/– Button
Keystone Button
Blank Button
Use to adjust the volume of the audio output.
Use to adjust the image vertically and make it square.
Use to blank the image and mute audio.
Use to freeze or unfreeze the image
Freeze Button
Mute Button
Use to turn on or off the speaker.
Zoom Button
Use the Zoom (+/-) buttons to zoom the image in and out. Use
the 4 directional selection buttons to pan the image.
Input Source
Selection
To select the correct device you are connecting with.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Installation Steps
Getting Started
1. Place the projector on a flat surface.
2. Position the projector at the desired distance from the screen.
3. The projection distance is less than 33 feet (10M).
CAUTION:
•
Proper ventilation is import. Don’t block ventilation openings. Never operate this
projector in an enclosed area. Do not place the projector on a tablecloth or other
soft covering that may block the vents. With ceiling installations, use approved
mounting hardware. Do not put the projector near heater, air ducts transformers or
other electrical devices. For permanent installations follow local codes.
Don’t set liquids on the projector. Spilled liquids may damage your projector.
Don’t put the projector on a hot surface or in direct sunlight.
•
•
•
Do not drop the projector.
Connecting the Projector
1. Connect the power cable
2. When you connect the power cable to the projector, the Power LED & Lamp Ready
LED on the control pad will illuminate, wait until LED stop flashing before turning on
the projector.
Lights in green
(Standby)
DVI input port
(connects to computer, HDTV,
and Component video player)
Audio input
Power outlet
AC IN Socket
S-Video input
USB Connector
Composite
Video input
(connects to PC mouse port so
Remote Control can be used as
a mouse control only)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Connecting Input and Output Devices
The cables are color coded to assist you in making the connections.
You can connect more than one image source at a time. The input source will be detected
automatically when enable the “Auto Source” function is enabled in the Status Menu of the
OSD MENU. Manually pressing the “Source” button operates selection.
The illustration below shows the ports and appropriate cables for connecting external devices
to the projector.
Power outlet
Computer (Notebook)
Computer (Desktop)
Power Cable
Audio Cable
(Stereo to Stereo)
Remote Mouse
Cable
Computer Cable (DVI to
D-Sub 15 pin VGA)
Audio Cable
Stereo Mini Jack to
RCAx2 (Red/White)
Component Video
Cable DVI-I to HDTV
Video Cable
S-Video
Cable
DVD player
VCR
HDTV/Component Video
14
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Starting the Projector
Power on
1. Remove the lens cap
2. Make sure Lamp LED ready in steady orange state.
3. Press Power on the remote control, or Power on the control pad, to turn on the unit.
NOTE:
•
When powered on, both the fans & lamp will be turned on. The power indicator
will begin to flash until a video source is found, and the lamp indicator will
extinguish when lamp is in normal status.
•
The projection image will be in full brightness within 10-15 seconds and the
“LUXEON” screen menu will appear.
CAUTION:
Don’t look directly into the lens when the lamp is on. Doing so may cause an eye
injury.
Turn on the source
1. Turn on the source
2. Selecting the source (PC or Video)
•
•
The “Auto Source” function will automatically find a source.
The Source button on the control panel or remote control can be used to select a
source.
NOTE:
•
Always turn off the image source (computer or video) and projector before
connecting or disconnecting cables.
•
When using a computer as the input device, set the resolution of your computer’s
graphic card to 1024x768 for the optimal projected image. Refer to the Timing
Charts page 31 to verify that the video signal timing of your graphics card is
supported by the projector.
•
•
Many laptop computers do not automatically turn on their external video port when
another display device is connected. Refer to your computer’s user guide for the
function key or command that activates the port. MAC users may need to turn on
SimulSCAN or monitor mirroring. Refer to the computer manual.
If a source is not found in 10 minute, the power will be automatically turned off.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Adjustment
Adjusting Projector Angle
Place the projector on a flat surface and position in the centre horizontally for best viewing.
Adjust the projector angle using the Height
Height
Adjustment
Adjustment Buttons.
Button
Press the Height Adjustment buttons while
tilting the projector. The Foot Adjuster will
extend accordingly, angled 7 degrees
upwards.
Foot Adjusters
NOTE:
Press the Height Adjustment button before
adjusting the Foot Adjusters to avoid resulting
in damage.
Adjusting the Zoom and Focus
Rotate the zoom ring and focus ring until the
Zoom Ring
projected image is clear and at the desired
size. The projector can focus within the range
of 5 feet (1.5m) to 33 feet (10m).
NOTE:
If vertical bars appear on the display after
adjusting the focus, press the “Auto” button
Focus Ring
on the Control Pad. Or use the
frequency/tracking features in the OSD menu
to manually adjust the synchronization and
tracking of the image.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Adjusting the Keystone Control
To adjust image vertically and make a square
image. Adjust the keystone function by pressing
the keystone button on the remote control or
through OSD menus.
Adjusting the Zoom and Pan
ZOOM
Press the zoom +/- buttons on remote control to
enter zoom mode, and use directional keys to pan
upward, downward, right, and left.
Four times as large
Original size
as the original size
□ Make any necessary image adjustments by using the on-screen menus.
(Refer page OSD Menu section for the details)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Power Off
1. Turn off the projector and image sources in the order listed here.
a. Computer
b. Projector
c. Audio Source (if different from your video source or computer).
d. Video source (such as VCR, DVD, HDTV).
2. Press the Power button on the top of the unit or remote control to turn off
the power.
A confirmation request will appear on the screen asking for reconfirmation of power off
request.
3. Press the Power button again to confirm.
The lamp will turn off immediately but the fan will continue running for 1 minute to cool
down the unit. The Power Indicator will continue flashing as long as the power cord is
connected to the projector.
Restart
To restart the unit shortly after powering off, user must wait for 1 minute for the lamp to cool
down. The lamp ready LED will stop flashing when the projector is ready to power up.
CAUTION:
The unit may remain HOT for up to 45 minutes upon power off. User should be
careful before handling the unit to prevent any burn or injury.
WARNING:
To reduce the risk of electric shock or damage to the equipment:
•
•
•
•
•
Do not disable the power cord-grounding plug. The grounding plug is an important
safety feature.
Plug the power cord into a grounded (earthed) electrical outlet that is easily
accessible at all times.
Disconnect power from the projector by unplugging the power cord from the
electrical outlet.
Do not place anything on top of power cords or cables. Arrange them so that no
one may accidentally step on or trip over them.
Do not pull on a cord or cable. When unplugging from the electrical outlet, grasp
the cord by the plug.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
On-Screen-Display Menu Format and Description
The OSD menu will appear if any button is pressed thru using the control pad and remote
control.
Input Source OSD
Display Logo
The projection image will appear in full brightness
within 10-15 seconds and the “LUXEON” logo will
appear on the screen.
No Input Signal
“No Input Signal” will show on the screen when
there is no active signal detected within 16 seconds.
Standby
When input signal is not detected for 16 seconds, the
splash screen will appear until a signal is detected.
Power Off
The splash screen will be displayed for 6 seconds
requesting power off confirmation.
Input Source
The splash screen will
be displayed upon
pressing the “Source”
button on the top
cover or the remote
control.
Press “bc” or
“Source” to select the
desired input source.
Source button on Remote control
Source button on control pad
19
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Ezkey OSD
By repeatedly pressing EZKEY the following menu can be scrolled though. The user may
adjust it to the desired level through keypads of Auto (-) and Source (+).
Keystone Correction
Use the (-) and (+) to adjust the vertical keystone
level of the image.
Frequency
Use the (-) and (+) to adjust the frequency.
Volume
Use the (-) and (+) to adjust the volume level.
Brightness
Use the (-) and (+) to adjust the display
brightness.
Remote Control Buttons OSD
Following menus/functions can be accessed through corresponding buttons on the remote
control.
Zoom & Pan
Use Zoom (+/-) keys to zoom the image in and out.
Use the 4 directional selection buttons to pan the
image.
Mute
Use the mute key to turn on or off the speaker.
Blank & Mute
Use blank key to blank the image and mute the Audio.
Freeze
Use the freeze key to freeze or unfreeze the Image.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
OSD Menu
Use the On-Screen-Display Menus shown below to adjust the projected image. To access and
adjust the On-Screen-Menu do the following:
1. Press the Menu button on the remote control to select one of six on-screen menus: Main
Menu, Setup Menu, Color Manager Menu, Language Menu, Utility Menu, and Status
Menu.
2. Press arrow keys Left / Right (W/X) for main menu selection, and use arrow keys
upward / downward (S/T ) for sub-menu or for adjustment selection.
3. Press the “menu” button to exit an OSD menu.
Main Menu
PC Mode
Video Mode
Contrast
Use arrow keys Left / Right (W/X) to adjust the contrast.
Adjustment range: from min-max (0 – 100) by 50 steps.
(Default value: factory calibrated)
Brightness
Use arrow keys Left / Right (W/X) to adjust the brightness.
Adjustment range: from dark – light (0-100) by 50 steps.
(Default value: factory calibrated)
Horizontal
Position
Use arrow keys Left / Right (W/X) to adjust the position in horizontal
direction.
Adjustment range: from left – right (0-100).
(Default value: centre position)
Vertical Position
Reset
Use arrow keys Left / Right (W/X) to adjust the position in vertical
direction.
Adjustment range: from bottom – top (0-100).
(Default value: centre position)
Use ↵ button to reset to default value.
In PC mode to reset contrast, brightness to default value.
In Video mode to reset contrast, brightness to default value.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Setup Menu
PC Mode
Video Mode
HDTV Mode
Use arrow keys Left / Right (W/X) to adjust the sampling clock to
eliminate flicker.
Frequency
Adjustment range: from low-high (0-100) by 32 steps.
(Default value: auto detected)
Use arrow keys Left / Right (W/X) to adjust the sampling number.
Adjustment range: from low - high (0 – 100) by 100 steps.
(Default value: auto detected)
Tracking
Use arrow keys Left / Right (W/X) to adjust the video automatic
gain control. Selection item: on / off.
(Default value: on)
Video AGC
Use arrow keys Left / Right (W/X) to adjust the video source type.
Selection item: RGB / Y-Pb-Pr (HD) / Y-Cb-Cr (DVD)
(Default value: Y-Pb-Pr)
Video Type
Use arrow keys Left / Right (W/X) to select the video aspect ratio.
Aspect Ratio
Selection item: 4:3 & 16:9. (Default value: 4:3)
Use arrow keys Left / Right (W/X) to select different projection
type.
Projection Type
Selection item: Desktop Front/Rear, Ceiling Front/Rear.
(Default value: desktop front)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Use arrow keys Left / Right (W/X) to adjust the volume level.
Adjustment range: from low - high (0-8) by 8 steps.
(Default value: 4)
Volume
Use arrow keys Left / Right (W/X) to adjust the keystone level of
Keystone
display.
Adjustment range: from
(Default value: 50)
to
(0-100) by 32 steps.
Use ↵ button to reset to default value.
Reset
In PC mode to reset aspect ratio, projection type, volume, keystone
to default value.
In Video mode to reset video AGC, aspect ration, projection type,
volume, keystone to default value.
In HDTV mode to reset video type, aspect ratio, projection type,
volume, keystone to default value.
Color Manager Menu
PC Mode
Video Mode
Use arrow keys Left / Right (W/X) to adjust the video source type.
Selection item: RGB / Y-Pb-Pr (HD) / Y-Cb-Cr (DVD)
(Default value: RGB)
Video Type
Color Temp.
Use arrow keys Left / Right (W/X) to select different color
temperature
Adjustment range: from cool, normal, warm by 3 steps.
(Default value: normal)
Color Saturation
Use arrow keys Left / Right (W/X) to adjust video saturation.
Adjustment range: from color off to color level (0 – 100) by 50
steps.
(Default value:50)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Color Tint
Use arrow keys Left / Right (W/X) to adjust the video tint/hue.
Adjustment range: from red to green (0-100) by 100 steps.
(Default value: 50)
OSD Translucent
Use arrow keys Left / Right (W/X) to select OSD background
translucent or not.
Adjustment range: translucent (on/off) by 2 steps.
(Default value: off)
Sharpness
Gamma
Use arrow keys Left / Right (W/X) to select different sharpness
level.
Adjustment range: from soft to clear (1-5) by 5 steps.
(Default value: 3)
Use arrow keys Left / Right (W/X) to select different gamma
correction.
Selection items: from PC, MAC, Graphic, Video and Black &
White by 5 steps.
(Default value: PC in PC mode, Video in Video mode)
Reset
Use ↵ button to reset to default value.
In PC mode to reset color temp, OSD translucent, gamma to default
value.
In Video/HDTV mode to reset color saturation, color tint, color
temp, gamma to default value.
Language Menu
Use arrow keys of Upward / Downward
(S/T) to select the desired language:
Chinese-Simplified, Chinese-Traditional,
English, French, German, Portuguese,
Spanish; and use the ↵ button to enter the
selected language.
(Default value: English)
24
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Utilities Menu
PC Mode
Video Mode
PIP Size
Use arrow keys Left / Right (W/X) to select different picture in
picture size. Selection items: off/small/medium/large by 4 steps.
(Default value: off)
PIP Position
PIP Input
Use arrow keys Left / Right (W/X) to select different picture in
picture position. Adjustment range: from upper left to bottom right
by 9 steps. (Default value: bottom right)
Use arrow keys Left / Right (W/X) to select different picture in
picture source. Selection items: Auto/S-video/Comp by 3 steps.
(Default value: auto)
Blank Color
OSD Position
Use arrow keys Left / Right (W/X)to select different blanking color
Selection items: Black / Red / Green / Blue by 4 steps.
(Default value: black)
Use arrow keys Left / Right (W/X) to select different OSD location
Selection items: from upper left to bottom right by 5 steps.
(Default value: centre)
OSD Display Time Use arrow keys Left / Right (W/X) to select auto timeout Selection
range: from 10 to 30 seconds by 21 steps.
(Default value: 15 seconds)
Reset
Use ↵ button to reset to default value.
In PC mode, to reset PIP size, PIP position, PIP input, blank color,
OSD position, and OSD display time at default value.
In Video/HDTV mode, to reset blank color, OSD position, OSD
display time at default value.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Status Menu
Auto Source
To turn on or off the automatic function to detect one or more
active input source.
Auto Power Off
To turn on or off the function for automatically lamp off when
there is no active signal.
Video Information To show resolution, H/V sync. information at RGB mode, color
standard at Video mode.
Software Revision Software version information.
Lamp Hours
Lamp hour used information.
Lamp Hour Reset
To reset lamp hour after changing the lamp. See page 36 for lamp
changing process.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Reference
Positioning the Projector
To adjust the size of the projected image, refer to figures 1 below and table 1 on the next
page for Projection Distances to increase/decrease the distance between the projector and the
projection screen.
Screen
Width
Screen
Height
Screen size
(diagonal)
Center of image
Figure 1 : Projection Distance vs. Image Size
27
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Distance
5 feet
(1.5m)
6.5 feet
(2m)
8 feet
(2.4m)
9 feet
Width x Height
Diagonal
31.12x23.34" - 37.34x28.01"
(0.78x0.59 - 0.94x0.70m)
41.49x31.12" - 49.79x37.34"
(1.04x0.78 - 1.25x0.94m)
49.79x37.34" - 59.75x44.81"
(1.25x0.94 - 1.50x1.13m)
58.09x43.57" - 69.71x52.28"
(1.46x1.10-1.75x1.32m)
62.24x46.68" - 74.69x56.02"
(1.57x1.17 - 1.88x1.41m)
66.39x49.79" - 79.67x59.75"
(1.67x1.25 - 2.01x1.50m)
74.69x56.02" - 89.63x67.22"
(1.88x1.41- 2.26x1.69m)
82.99x62.24" - 99.58x74.69"
(2.09x1.57 - 2.51x1.88m)
91.29x68.46" - 109.54x82.16"
(2.30x1.72 - 2.76x2.07m)
99.58x74.69" - 119.50x89.63"
(2.51x1.88 - 3.01x2.26m)
103.73x77.80" - 124.48x93.36"
(2.61x1.96 - 3.13x2.35m)
107.88x80.91" - 129.46x97.09"
(2.72x2.04 - 3.26x2.44m)
116.18x87.14" - 139.42x104.56"
(2.92x2.19 - 3.51-2.63m)
124.48x93.36" - 149.38x112.03"
(3.13x2.35 - 3.76x2.82m)
145.23x108.92" - 174.27x130.70"
(3.66x2.74 - 4.39x3.29m)
165.97x124.48" - 199.17x149.38"
(4.18x3.13 - 5.01x3.76m)
207.47x155.60" - 248.96x186.72"
(5.22x3.92 - 6.27x4.70m)
38.90 - 46.68"
(0.98 -1.17 m)
51.87 - 62.24"
(1.31 - 1.57m)
62.24" - 74.69"
(1.57 - 1.88m)
72.61" - 87.14"
(1.83 - 2.19m)
77.80" - 93.36"
(1.96 - 2.35m)
82.99" - 99.58"
(2.09 - 2.51m)
93.36" - 112.03"
(2.35 - 2.82m)
103.73" - 124.48"
(2.61- 3.13m)
114.11" - 136.93"
(2.87 - 3.45m)
124.48" - 149.38"
(3.13 - 3.76m)
129.67" - 155.60"
(3.26 - 3.92m)
134.85" - 161.82"
(3.39 - 4.07m)
145.23" - 174.27"
(3.66 - 4.39m)
155.60" - 186.72"
(3.92 - 4.70m)
181.53" - 217.84"
(4.57 - 5.48m)
207.47" - 248.96"
(5.22 - 6.27m)
259.33" - 311.20"
(6.53 - 7.83m)
(2.8m)
9.8 feet
(3m)
10.5 feet
(3.2m)
12 feet
(3.6m)
13 feet
(4m)
14.5 feet
(4.4m)
16 feet
(4.8m)
16.4 feet
(5m)
17 feet
(5.2m)
18 feet
(5.6m)
20 feet
(6m)
23 feet
(7m)
26.2 feet
(8m)
33 feet
(10m)
Table 1 : Projection Distances vs. Image Size
28
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Remote Control Transmission Range
The Remote Control shall function at a distance within the range that the IR Transceiver can
receive. For best operation, kindly refer to the following illustration of the Remote Control
and IR transceiver transmission range and distance.
The projector is equipped with an IR
Transceiver located at the front cover of the
unit for the receipt of remote control
transmission.
The IR Transceiver can receive a transmission
signal with the effective range of 60° from an
outstretched arm pointed towards the IR
Transceiver.
The effective transmission distance of the
remote control is about 10 meter, including the
reflection distance, response from the screen
to the remote control.
5M
Users, using the remote control can, either
point it directly at the IR Transceiver, or stand
behind the unit and point it at the projected
image.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Product Specification
Display Type
Panel
DLP Projection System
0.7" DMD x 1
Native Resolution
Data Compatibility
Zoom Ratio
Color Reproduction
Aspect Ratio
Digital Keystone Correction
Horizontal Frequency
Vertical Scan Rate
Projection / Installation Mode
Lamp Type
XGA (1024 X 768 ) Native
VGA, SVGA, XGA, SXGA, Macintosh
1: 1.20 Manual Zoom / Focus
16.7 Million
4:3 / 16:9 screen selectable
(V) +/- 15 degree
15, 31 - 90 KHz
43 - 85 Hz
Front / Rear / Desktop / Ceiling
150W VIP
Projection Distance
Projection Image Size (diagonal)
Audio Noise
1.5 to 10 meters
40" to 311"
35 dB
Input Terminals
Output Terminals
Speakers
DVI-I, Video, S-Video, Audio
USB for mouse control
0.5W x 1
Video Compatible
Dimensions (WxDxH)
Weight
NTSC, NTSC 4.43, PAL, SECAM
188mm x 240mm x 64mm (7.4” x 9.5” x 2.5”)
3.5 lbs
Power Supply
Power Consumption
On-Screen Display Language
100 - 240vac, 47-63 Hz
220 Watts
English, French, Spanish, German, Portuguese,
Traditional Chinese, Simplified Chinese
UL, Cul, CE, TUV, FCC Class B, CCC
10-35 ° C
Safety & Regulatory
Operation Temperature Range
Storage Temperature Range
Operating Relative Humidity
-20 ∼ 60° C
5% ∼ 90% Non-Condensing
Storage Relative Humidity
Altitude (operating)
5% ∼ 95% Non-Condensing
0 ∼ 10,000 ft
0 ∼ 3,048 m
0 ∼ 40,000 ft
Altitude (storage)
0 ∼ 12,192 m
30
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Timing Charts
The projector can display several resolutions. The following table outlines the resolutions
that can be displayed by the projector.
Table 2: ANALOG Computer Timings (Resolution and Refresh Rate【fV】)
Resolution
640 x 350
640 x 480
640 x 480
640 x 480
640 x 480
720 x 400
720 x 400
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1280 x 1024
1280 x 1024
640 x 480
832 x 624
1280 x 1024
FH(kHz)
37.9
31.5
37.9
37.5
43.3
31.5
37.9
37.9
48.1
46.9
53.7
35.5
56.5
68.7
64.0
79.98
35.0
49.73
64.0
FV (Hz)
85
Signal mode
Expanded VGA
Expanded VGA
Expanded VGA
Expanded VGA
Expanded VGA
Expanded VGA
Expanded VGA
Expanded SVGA
Expanded SVGA
Expanded SVGA
Expanded SVGA
Native XGA
60
72
75
85
70
85
60
72
75
85
43.4
70
85
60
75
66.68
74.55
60
Native XGA
Native XGA
Compressed SXGA
Compressed SXGA
Expanded Mac II 13”
Expanded Mac 16”
Compressed FM Town
Table 3: DIGITAL Computer Timings (Resolution and Refresh Rate 【fV】
Resolution
640 x 350
640 x 480
640 x 480
640 x 480
640 x 480
720 x 400
720 x 400
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1280 x 1024
640 x 480
832 x 624
1280 x 1024
FH(kHz)
37.9
31.5
37.9
37.5
43.3
31.5
37.9
37.9
48.1
46.9
53.7
35.5
56.5
68.7
64.0
35.0
49.73
64.0
FV (Hz)
85
Signal mode
Expanded VGA
Expanded VGA
Expanded VGA
Expanded VGA
Expanded VGA
Expanded VGA
Expanded VGA
Expanded SVGA
Expanded SVGA
Expanded SVGA
Expanded SVGA
Native XGA
60
72
75
85
70
85
60
72
75
85
43.4
70
85
Native XGA
Native XGA
Compressed SXGA
Expanded Mac II 13”
Expanded Mac 16”
Compressed FM Town
60
66.68
74.55
60
31
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Troubleshooting
Power Indicator
The power and lamp indicator on the control pad provides you with information about the
condition of the projector.
Indicator Light Status
Lamp Blinking
Ready
Condition
• Lamp is off but power cord is connected to the projector.
• Projector is in standby mode.
• Lamp is off and fan is running.
• Projector is cooling down.
Scaling chip has malfunctioned.
System has overheated.
I2C bus has failed
Lamp has malfunctioned
Fan has malfunctioned
LED
Power Two blinks
LED
Three blinks
Four blinks
Five blinks
Six blinks
Seven blinks
Eight blinks
Lamp cover is open.
DMD board failure. Call for service.
NOTE
Every blink will last for 1/2 second and the interval for every blink is lasted 1 second.
Remote Control
Symptom
Projector responds poorly or
not at all to the remote
control.
Cause and Solution
• Make sure that the total distance from the remote to the
projector is no more than 33 feet (10m).
• Point the remote control at the screen or at the front of the
projector.
• Make sure nothing is blocking the infrared sensor on the
front of the projector.
• Darken the room. The light might be effecting the remote
Control.
• Replace the remote control batteries.
Sound
Symptom
No sound
Cause and Solution
• Adjust volume
• Verify audio/input connections
• Adjust audio source
Poor sound quality
• Make sure your are connected to the earphone jack on
your laptop or line out jack on your desktop.
• Make sure the volume setting on your computers is to the
halfway point.
No audio-out port on the
image source
You will be not able to connect audio to the projector.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Image Source
Symptom
Cause and Solution
The S-Video image source
does not appear.
Only the start-up screen
appears and not the image
from the image source.
The image source is
• Be sure to use the cable that comes with your projector. Some
inexpensive cables are not compatible with the projector.
• Verify that the cables are connected correctly.
• Verify that the proper image source is connected and the
proper functions are enable of the menu.
• Make sure that the image source is turned on.
• Turn off everything and power up again following the proper
procedure.
connected but a “No
Signal Message” appears.
• Make sure that your laptop’s external video port is turned on.
Image Quality
Symptom
Color or text is not being
projected.
Solution
• Adjust the brightness up or down until the text is visible.
Some text or fonts are not
as sharp on the projector
as the are on the computer.
Image isn’t centred on the
screen.
• For optimal results, set the computer’s resolution to
1024x768. (Refer to your computer user manual.) This
projector is capable of projecting up to 1280 x 1024.
• Be sure that the projector is at a 90° angle to the screen.
• Reposition the image.
Image is out of focus.
• Make sure that the projection screen is at least 5 ft (1.5m)
from the projector.
• Turn the projection lens till the image is focused.
• Check the projection lens to see if it needs cleaning.
Check main menu of Setup to make sure projection type is
correct in accordance with the projection status.
• If projecting from a ceiling mount, make sure that the ceiling
projection function is selected.
Image and menus are
upside down.
• If projecting from an upright position, make sure that Front or
Rear projection is selected.
Image and menus are
Check main menu of Setup to make sure projection type is
reversed from left to right. correct in accordance with the projection status.
• If projecting from behind a screen make sure that Rear
projection is selected.
• If projection in front of a screen, make sure that Front or
Ceiling Projection is selected.
Image appears flat with no To adjust the contrast:
contrast.
1. Press Menu key on the remote and go into Main menu.
2. Select “contrast” and use the cursor keys +/- to increase or
decrease the contrast to the desired level.
Image appears washed out
or dark
• Check projection lens to see if it needs cleaning.
• To adjust the brightness
1. Press Menu on the remote and go into Main menu.
2. Select “Brightness” and use arrow keys +/- to increase or
decrease the brightness to the desired level.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Image is blocked
Press Menu on the remote and go into the main menu of Utility
• To disable PIP Size function
• To check PIP Input selection
PIP window can not
display video
Image is “noisy” or
streaked.
• To adjust the frequency
1. Press Menu to go into main menu of “Setup”.
2. Adjust “ Frequency” and “Tracking” to an optimal setting.
• Try connecting with another computer. The problem might be
due to the video card of the connected computer itself.
Image is wider at the top This keystone effect is caused by the projection angle not being
or bottom of the screen.
perpendicular to the screen. To achieve a square image, raise or
lower the front legs or prop up the back of the projector, or adjust
keystone function thru remote, or use the EZ Key on the top
cover of the main set.
Image is wider at one side Make sure the projector is set at a 90 degree angle to the screen.
than the other.
Projected colors don’t
match the computer or
video source colors.
Press menu to go into main menu of “Color Manager” and adjust
color temperature & gamma to optimize the colors.
The Image Manager settings work best if you reset the main
menu and Adjust to the prior to setting Color Manager.
Press menu key on the remote to go into several function keys
Adjust Function can not
find from Ezkey on main selection.
set or remote
Lamp
Symptom
No light is coming from the
lamp.
Cause and Solution
• Make sure that the power cable is properly connected to a
fully functional AC electric outlet.
• Make sure that the power cord is properly connected to the
projector.
• Make sure that you have removed the lens cap on the
projector lens at the front of the projector.
• Make sure you have pressed the power button and the
power LED light is a steady green.
• Check the projector’s lamp to make sure that it is securely
connected in the lamp module.
• Make sure that the lamp module door is fully closed.
• Make sure that the cable connectors do not have any bent
pins.
• Replace the lamp
Lamp shuts off
• A minor power surge may cause the lamp to shut off. Press
the power button twice to turn off the projector. (The
power light continues to blink and the fan continues to run
until the projector cools down.) Wait at least one minute,
then press the power button again.
• Replace the lamp module.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Maintenance
Changing the Lamp
Important! The lamp contains a trace amount of mercury. Some governments require
special disposal of lamps containing mercury. Dispose of lamps in accordance with the law
and any applicable local regulations.
The lamp module should be replaced with a certified replacement part. To order a new
lamp, contact your local dealer. After changing the lamp module you should reset the lamp
hours in accordance with the lamp hour reset instructed hereafter.
WARNING:
When replacing the lamp be sure to turn off power and unplug the power cord. To
avoid being burned and to prevent an electrical shock, wait 45 minutes before
opening the lamp module cover and do not touch any hot surface inside.
Do not loosen or remove any screws other than lamp module or its cover.
Doing so many cause electric shock.
To replace the lamp module
1. Turn off the projector and let the unit cool
down for at least 45 minutes.
2. Unplug the power cord from projector.
3. Turn the projector upside down. Loosen the
screw with a phillips screwdriver. Remove the
lamp cover by lifting it up and out.
4. Loosen the three screws on the lamp module
bracket.
5. Gently lift and pull up on the two slotted
indentation on the located on the lamp
housing to remove the lamp module.
6. Carefully place the new lamp module into the
projector with the glass portion facing left.
Insert the lamp module securely and match
two location ribs to the location holes on the
inner engine case. Tighten the three screws.
7. Reinstall the lamp module cover and tighten
the screw.
8. Turn on the projector.
9. Reset the lamp hours.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
NOTE:
1. The lamp contains a trace amount of mercury. Some governments required special
disposal of lamps containing mercury. Dispose of lamps in accordance with the law and
any applicable local regulations.
2. Do not loosen or remove any screw other than lamp unit or its cover.
3. Do not touch any of the glass surface on the lamp unit.
Lamp Hour Reset
Press the cursor keys through following
sequence to reset Lamp hour:
downbJupcJlefteJrightf
Press “Exit” to cancel
Changing the Battery of Remote Control
•
Remove the battery cover.
Push the knob while lifting up the cover of
the battery compartment.
•
Insert the batteries.
Install AAA battery x2 (included) into the
remote. Make sure they are in the correct
direction (+) and minus (-) placed.
•
Replace the cover to the battery
compartment.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Cleaning
Cleaning the Projection Lens
1. Be sure the projector is powered-off and has cooled down.
2. Unplug the projector.
3. Remove the lens cap.
4. Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
5. Lightly wipe the cleaning cloth over the lens.
NOTE: Always keep lens cap on the projector when not in use.
CAUTION:
•
Avoid using an excessive amount of camera lens cleaner. Do not use abrasive
cleaners, solvents or other harsh chemicals as they might scratch the lens.
Do not spill any camera lens cleaner on the exterior case as it may fade, deform or
melt the exterior case.
•
Cleaning Exterior Case
1. Be sure the projector is powered-off and has cooled down..
2. Unplug the projector.
3. Wipe off the dirt or dust on the case with a soft, dry, lint-free cloth.
4. Moisten a soft cloth with water or a non-abrasive is recommended to clean off stubborn
dirt or stains.
CAUTION:
Do not use alcohol, benzene, thinner or other chemical cleaners, which may fade,
deform or melt the exterior case. Do not apply a detergent solution to the projector
lens as it may scratch the lens.
Cleaning the Projector
Never attempt to clean the interior of the projector. Clean the exterior of the projector only.
1. Make sure the projector is powered-off, cooled down and power cord has been
disconnected prior.
2. Clean the exterior of the projector with a moist cloth using a mild detergent.
WARNING:
Do not use lens cleaner, alcohol, benzene, thinner or other chemical cleaners to clean the
exterior case.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP Digital Projector User’s Guide
Customer Support
For most of your questions, it is suggested that you contact your dealer for assistance or ask
your dealer to refer you to a service centre
To facilitate after-sales service process, it is suggested that you fill in following information
when you purchase this product.
For Your Records
Product Name:
Model Number:
Serial Number:
Purchase Date:
Service Information
Contact Person
Company
Address
Telephone
Fax No.
E-mail
Product Warranty : from
Lamp Warranty : from
to
to
Product disposal at end of product life
Please dispose of this product properly at the end of its useful life. Your local waste disposal
company may provide information about proper disposal.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
|