®
DEFINITY Extender
Remote Module
User’s Guide
555-230-796
Comcode 107634560
Issue 2
July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Trademarks
DEFINITY is a registered trademark of Lucent Technologies in the US and other countries.
Ordering Information
Call:
Lucent Technologies Publications Center
Voice 1 800 457-1235 International Voice 765 361-5353
Fax 1 800 457-1764
International Fax 765 361-5355
Write:
Order:
Lucent Technologies Publications Center
P.O. Box 4100
Crawfordsville, IN 47933
Document No. 555-230-796
Comcode 107634560
Issue 2, July 1997
For more information about Lucent Technologies documents, refer to the section entitled “Related
Documents” in “About This Book”
Support Telephone Number
In the continental US, Lucent Technologies provides a toll-free customer helpline 24 hours a day.
Call the Lucent Technologies Helpline at 1 800 242-2121 or your Lucent Technologies authorized
dealer if you need assistance when installing programming, or using your system. Outside the
continental US, contact your local Lucent Technologies representative.
Warranty
Lucent Technologies provides a limited warranty on this product. Refer to “Limited Warranty” in
“Customer Support Information.”
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Customer Support Information ........................ix
■
■
Support Telephone Number.....................................ix
Security of Your System:
Preventing Toll Fraud...............................................x
Lucent Technologies Fraud Intervention..................xi
Limited Warranty......................................................xii
FCC Notification and Repair Information .................xiii
Installation and Operational Procedures ..................xiv
Federal Communications Commission (FCC)
Electromagnetic Interference Information................xvi
■
■
■
■
■
About This Book ....................................................xvii
■
Intended Audience ...................................................xvii
■
Terms and Conventions...........................................xviii
■
Typographical Conventions......................................xix
■
How to Use This Book..............................................xix
■
Product Safety Labels ..............................................xx
■
Related Documents..................................................xxi
■
How to Comment on This Document.......................xxiii
Issue 2 July 1997 i
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1
Introduction ............................................................ 1-1
■
System Operation and Configuration....................... 1-2
Equipment List.................................................... 1-3
Compatibility ....................................................... 1-5
Options ............................................................... 1-5
Specifications........................................................... 1-6
Considerations......................................................... 1-8
■
■
2
Installation .....................................................................2-1
■
Location Requirements............................................ 2-2
■
Electrical Requirements........................................... 2-2
■
Connecting the Remote Module .............................. 2-3
■
Installation Procedure.............................................. 2-4
Connections for Data Transmission ................... 2-6
ii Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
3
Programming ................................................................3-1
■
■
■
Using the Telephone for Programming ....................3-2
Setting the Telephone Number ................................3-3
Setting the Mode of Dialing ......................................3-4
Setting Pulse Dialing ...........................................3-4
Setting Tone Dialing............................................3-5
Setting the Connect Rate .........................................3-6
Setting the COM Port Baud Rate .............................3-8
Exiting Programming................................................3-9
■
■
■
4
Operating the Remote Module............................4-1
■
Starting the Operation ............................................4-2
■
Disconnecting.........................................................4-4
■
Changing a Password ............................................4-6
■
Checking System Software ....................................4-9
Issue 2 July 1997 iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
5
Troubleshooting..........................................................5-1
■
■
■
Troubleshooting ..................................................... 5-2
LED Sequences..................................................... 5-3
Error Messages ..................................................... 5-3
GL Glossary ...........................................................................GL-1
iv Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Figures
1
2
Introduction
1-1
System Configuration.........................................1-2
Installation
2-1
2-2
Remote Module Back Panel...............................2-3
RS-232 Cable Pin Connections .........................2-7
4
Operating the Remote Module
4-1
Connect Sequence for the Remote Module.......4-3
Issue 2 July 1997 v
Download from Www.Somanuals.com. All Manuals Search And Download.
Tables
1
2
3
5
Introduction
1-1
Remote Module Specifications.......................... 1-7
Installation
2-1
DIP Switch Configuration................................... 2-5
Programming
3-1
Telephone Keys Used in Programming............. 3-2
Troubleshooting
5-1
Error Messages ................................................. 5-4
vi Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
The exclamation point in an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
IMPORTANT SAFETY INSTRUCTIONS
When installing telephone equipment, always follow basic safety
precautions to reduce the risk of fire, electrical shock, and injury to
persons, including:
■
Read and understand all instructions.
■
Follow all warnings and instructions marked on or packed with
the product.
■
Never install this unit or telephone wiring for it during a lightning
storm.
■
Never install a telephone jack in a wet location unless the jack
is specifically designed for wet locations.
■
Never touch uninsulated telephone wires or terminals unless
the telephone wiring has been disconnected at the network
interface.
■
Use caution when installing or modifying telephone lines.
■
Use only Lucent Technologies-manufactured DEFINITY
Enterprise Communications Server (ECS) circuit packs, carrier
assemblies, and power units in the DEFINITY ECS control unit.
■
Use only Lucent Technologies-recommended/approved
DEFINITY ECS accessories.
Issue 2 July 1997 vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
■
Do not install this product near water, for example, in a wet
basement location.
■
Do not overload wall outlets, as this can result in the risk of fire
or electrical shock.
■
Do not attach the power supply cord to building surfaces. Do
not allow anything to rest on the power cord. Do not locate this
product where the cord will be abused by persons walking on it.
■
Unplug the product from the wall outlet before cleaning. Use a
damp cloth for cleaning. Do not use cleaners or aerosol
cleaners.
■
Do not operate the system if chemical gas leakage is suspected
in the area. Use telephones located in some other safe area to
report the trouble.
WARNING:
DO NOT open the Remote Module. There are no
user serviceable parts inside the unit. Only an
authorized technician should open the unit for
required maintenance or upgrading purposes.
SAVE THESE INSTRUCTIONS
viii Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support Information
Support Telephone Number
In the USA only, Lucent Technologies provides a toll-tree
customer Helpline (1 800 242-2121) 24 hours a day. If you need
assistance when installing, programming, or using your system, call
the Helpline, or your Lucent Technologies authorized
representative.
Outside the USA, if you need assistance when installing,
programming, or using your system, contact your Lucent
Technologies authorized representative.
Issue 2 July 1997 ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support Information
Security of Your System:
Preventing Toll Fraud
As a customer of a new telephone system, you should be aware
that there is an increasing problem of telephone toll fraud.
Telephone toll fraud can occur in many forms, despite the
numerous efforts of telephone companies and telephone
equipment manufacturers to control it. Some individuals use
electronic devices to prevent or falsify records of these calls.
Others charge calls to someone else’s number by illegally using
lost or stolen calling cards, billing innocent parties, clipping on to
someone else’s line, or breaking into someone else’s telephone
equipment physically or electronically. In certain instances,
unauthorized individuals make connections to the telephone
network through the use of remote access features.
Common carriers are required by law to collect their tariffed
charges. While these charges are fraudulent charges made by
persons with criminal intent, applicable tariffs state that the
customer of record is responsible for payment of all long-distance
or other network charges. Lucent Technologies cannot be
responsible for such charges and will not make any allowance or
give any credit for charges that result from unauthorized access.
To minimize the risk of unauthorized access to your DEFINITY
ECS:
■
When possible, restrict the off-network capability of off-
premises callers, using calling restrictions, Facility Restriction
Levels, and Disallowed List capabilities.
■
When possible, block out-of-hours calling.
■
Frequently monitor system call detail reports for quicker
detection of any unauthorized or abnormal calling patterns.
x Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support Information
■
Limit Outcalling to persons on a need-to-have basis.
The DEFINITY ECS, through proper administration, can help you
reduce the risk of unauthorized persons gaining access to the
network. However, phone numbers and authorization codes can be
compromised when overheard in a public location, lost through
theft of a wallet or purse containing access information, or when
treated carelessly (writing codes on a piece of paper and
improperly discarding them).
Additionally, hackers may use a computer to dial an access code
and then publish the information to other hackers. Substantial
charges can accumulate quickly. It is your responsibility to take
appropriate steps to implement the features properly, to evaluate
and administer the various restriction levels, and to protect and
carefully distribute access codes.
Under applicable tariffs, you will be responsible for payment of toll
charges. Lucent Technologies cannot be responsible for such
charges and will not make any allowance or give any credit
resulting from unauthorized access.
Lucent Technologies Fraud
Intervention
If you suspect you are being victimized by toll fraud and you need
technical support or assistance, call the National Customer Service
Center at 1 800 242-2121.
Issue 2 July 1997 xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support Information
Limited Warranty
Lucent Technologies Inc. warrants this equipment to be free of
defects in materials and workmanship for a period of one year from
date of shipment. All defects within this time will be repaired without
charge upon return of the unit to the factory.
This warranty is null and void if the manufacturer determines that
any modifications have been made to the unit or the unit has been
subjected to physical or electrical stress.
This warranty covers parts and labor only and does not include
shipping costs, travel expenses, or travel time.
Installation of the equipment is the sole responsibility of the
purchaser. The manufacturer, its agents, or its distributors accept
no responsibility for malfunction or damage caused by improper
treatment or connection of the unit.
The manufacturer, its agents, or its distributors are not liable for
any losses incurred through use or malfunction of the equipment or
any losses or damages incurred by the use of the equipment in any
means whatsoever.
This warranty is limited to the repair of the equipment to its normal
functioning capability.
This warranty is complete as stated and all other warranties,
expressed or implied, are invalid.
The DEFINITY Extender System should be installed only by
qualified personnel. No user-serviceable parts are contained within
the units. Installation or programming should not begin prior to
review of all sections of this manual.
xii Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support Information
FCC Notification
and Repair Information
This equipment is registered with the FCC in accordance with Part
68 of its rules. In compliance with those rules, you are advised of
the following:
■
Means of Connection. Connection of this equipment to the
telephone network shall be through a standard network
interface jack, USOC RJ11C. These USOCs must be ordered
from your telephone company.
■
Party Lines and Coin Telephones. This equipment can not be
used with party lines or coin telephone lines.
■
Notification to the Telephone Companies. Before connecting
this equipment, you or your equipment supplier must notify your
local telephone company’s business office of the following:
— The telephone number(s) you will be using with this
equipment.
— The appropriate registration number and ringer equivalence
number (REN), which can be found on the back or bottom
of the control unit.
— For each jack, the sequence in which lines are to be
connected, the line types, the Facility Interface Code (FIC),
and the Ringer Equivalence Number (REN) by position
when applicable.
Issue 2 July 1997 xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support Information
■
Ringer Equivalence Number (REN). The REN is used to
determine the number of devices that can be connected to the
telephone line. Excessive RENs on the line can result in the
devices not ringing in response to an incoming call. In most, but
not all, areas the sum of the RENs should not exceed five (5.0).
To be certain of the number of devices that can be connected
to the line, as determined by the total RENs, contact the local
telephone company to determine the maximum REN for the
calling area.
■
Disconnection. You must also notify your local telephone
company if and when this equipment is permanently
disconnected from the line(s).
Installation and Operational
Procedures
This manual contains information about installation and operational
procedures.
■
Repair Instructions. If you experience trouble because your
equipment is malfunctioning, the FCC requires that the
equipment not be used and that it be disconnected from the
network until the problem has been corrected. Repairs to this
equipment can be made only by the manufacturers, their
authorized agents, or others who may be authorized by the
FCC. In the event repairs are needed on this equipment,
contact your authorized Lucent Technologies dealer or, in the
USA only, contact the National Service Assistance Center
(NSAC) at 1 800 242-2121.
xiv Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support Information
■
Rights of the Local Telephone Company. If this equipment
causes harm to the telephone network, the local telephone
company may discontinue your service temporarily. If possible,
they will notify you in advance. But if advance notice is not
practical, you will be notified as soon as possible. You will also
be informed of your right to file a complaint with the FCC.
■
Changes at Local Telephone Company. Your local telephone
company may make changes in its facilities, equipment,
operations, or procedures that affect the proper functioning of
this equipment. If they do, you will be notified in advance to give
you an opportunity to maintain uninterrupted telephone service.
■
New Network Area and Exchange Codes. The DEFINITY
ECS software does not restrict access to any new area codes
or exchange codes established by a local telephone company.
If the user has established toll restrictions on the system that
could restrict access, then the user should check the lists of
allowed and disallowed dial codes and modify them as needed.
■
Equal Access Codes. This equipment is capable of providing
users access to interstate providers of operator services
through the use of access codes. Modifications of this
equipment by call aggregators to block access dialing codes is
a violation of the Telephone Operator Consumers Act of 1990.
Issue 2 July 1997 xv
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support Information
Federal Communications
Commission (FCC)
Electromagnetic Interference
Information
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
residential environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications.
xvi Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Book
Intended Audience
This book is intended to help in the installation, system
administration, and maintenance of the DEFINITY Extender
Remote Module. It is intended for use as a reference by anyone
needing such information, including system managers, support
personnel, sales representatives, and account executives. It is also
intended for technicians who are responsible for system
installation, maintenance, and troubleshooting.
Issue 2 July 1997 xvii
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Book
Terms and Conventions
The DEFINITY Extender Remote Module will henceforth be
referred to as the Remote Module.
The DEFINITY Extender Switch Module will henceforth be referred
to as the Switch Module.
Throughout this document, toll fraud security hazards are indicated
by an exclamation point inside a triangle and the words Security
Alert.
Security Alert:
Security Alert indicates the presence of toll fraud
security hazard. Toll fraud is the unauthorized use of
your telecommunications system by an unauthorized
party (e.g., persons other than your company’s
employees, agents, subcontractors, or persons
working on your company’s behalf). Be sure to read
“Your Responsibility for Your System’s Security” on
the inside front cover of this book and “Security of
Your System: Preventing Toll Fraud” in About This
Book.
xviii Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Book
Typographical Conventions
Certain type fonts and styles act as visual cues to help you rapidly
understand the information presented:
Example
Purpose
Do not recycle old passwords.
Italics indicate emphasis.
If you do not want to disconnect,
go to Step 3.
Italics also tell you instructions
about what to do next in a
procedure.
At the "Go Online" screen, press
3 until the following screen
appears:
A number in a shaded box is used
to designate a key on your
telephone.
The names of fixed-feature,
factory-imprinted buttons on a
telephone appear in bold.
Press the Drop button four
times.
2:OK 3:Next
Plain constant-width type in a
shaded box indicates text that
appears on the telephone display.
How to Use This Book
This book is organized into chapters that give information on
procedures necessary for the proper installation and administration
of your DEFINITY Extender Remote Module.
“Related Documents,” later in this section, provides a complete list
of system documentation, together with ordering information.
Issue 2 July 1997 xix
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Book
If you have problems with your Remote Module, contact your
system administrator. If the problem can not be solved by the
system administrator, in the continental US, your system
administrator will call our toll-free Helpline, available 24 hours a
day, at 1 800 242-2121. Outside of the continental US, contact your
Lucent Technologies representative or local Authorized Dealer.
Product Safety Labels
Throughout this document, hazardous situations are indicated by
an exclamation point inside a triangle and the word Caution or
Warning.
WARNING:
Warning indicates the presence of a hazard that
could cause death or severe personal injury if the
hazard is not avoided.
CAUTION:
Caution indicates the presence of a hazard that could
cause minor personal injury or property damage if the
hazard is not avoided.
xx Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Book
Related Documents
The documents listed below are part of the DEFINITY ECS
documentation set. These documents can be ordered from the
Lucent Technologies Publications Center.
Call:
Lucent Technologies Publications Center
Voice 1 800 457-1235
Fax 1 800 457-1764
International Voice 765 361-5353
International Fax 765 361-5355
Write:
Lucent Technologies Publications Center
P.O. Box 4100
Crawfordsville, IN 47933
Issue 2 July 1997 xxi
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Book
Document No.
Title
DEFINITY Enterprise
Communications Server (ECS)
Release 3 System Documents
555-230-894
555-230-655
Installation for Single-Carrier Cabinets
Implementation Guide, Issue 1
Toll Fraud Security
555-025-600
BCS Products Security Handbook
DEFINITY Enterprise
Communications Server (ECS)
Release 3.0 Telephone User
Support
555-230-763
555-230-765
555-230-792
555-015-168
8410 Voice Terminal User's Guide
8434 Voice Terminal User's Guide
Callmaster II and III User's Guide
Callmaster II and III Voice Terminal
Installation and Use
555-015-169
Callmaster II and III Voice Terminal
Programming Options
xxii Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Book
How to Comment on This
Document
We welcome your comments, both positive and negative. Please
use the feedback form on the next page to let us know how we can
continue to serve you. If the feedback form is missing, write directly
to:
Documentation Manager
Lucent Technologies
211 Mount Airy Road
Room 2W-226
Basking Ridge, NJ 07920-2332
Issue 2 July 1997 xxiii
Download from Www.Somanuals.com. All Manuals Search And Download.
FEEDBACK FORM
DEFINITY® Enterprise Communications Server (ECS), Release 3
®
Title: DEFINITY Extender Remote Module
Document No.: 555-230-796 Issue: 2 Date: July 1997
1. Please rate the effectiveness of this book in the following areas:
Excellent
Good
Fair
Poor
Not
Applicable
Ease of Use
Clarity
Completeness
Accuracy
Organization
Appearance
Examples
Illustrations
Overall
Satisfaction
2. Please check ways you feel we could improve this book:
❑ Improve the overview
❑ Add more examples
❑ Add more detail
❑ Improve the organization
❑ Improve the index/glossary
❑ Add troubleshooting
❑ Add more step-by-step procedures
❑ Improve the table of contents
❑ Make it less technical
❑ Make it more concise
❑ Include more illustrations
❑ Add more/better quick information
reference aids
Download from Www.Somanuals.com. All Manuals Search And Download.
❑ Other
3. What did you like most about this book?
4. Feel free to write any comments below or on an attached sheet.
If we may contact you about your comments, please complete the following:
Name:
Telephone Number:
Company/Organization:
Date:
Address:
Send completed forms to: Documentation Manager, Lucent Technologies,
211 Mount Airy Road, Room 2W-226, Basking Ridge, NJ 07920-2332. Fax:
908 953-6912.
THIS FORM MAY BE PHOTOCOPIED
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
1
An overview of the functioning and specifications of the
DEFINITY Extender
®
®
The DEFINITY Extender enables DEFINITY telephone users to
be a fully functional part of the PBX telephone system with a digital
telephone located any distance off-premise. The Extender is
transparent to the user and retains access to the features and
functions of the DEFINITY Enterprise Communications Server
(ECS). In addition, an RS-232 data port extension is incorporated,
allowing the user to connect off-premise RS-232 equipment to
equipment at the PBX location.
Issue 2 July 1997 1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
System Operation and
Configuration
The DEFINITY Extender system is designed for use with a
DEFINITY ECS of Version 3, Release 3 or later. The Extender
system consists of two modules. One module, identified as the
Switch Module, connects to your PBX. The other module, identified
as the Remote Module, connects to your DEFINITY telephone at
your off-premise location. Figure 1-1 shows the Extender system
configuration.
Figure 1-1. System Configuration
The modules communicate via a single analog telephone line (also
called a “plain old telephone service” [POTS] line), which can
extend your DEFINITY telephone to virtually unlimited distances.
See “Specifications” later in this chapter for detailed circuit
specifications.
1-2 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The Switch Module emulates your telephone, and the Remote
Module emulates your PBX. Each module features a V.32terbo
internal modem for the transmission of all signals between the two
modules. With the use of Lucent Technologies’ DEFINITY
Extender system, the features and capabilities of your on-premise
telephones are extended to those off-premise.
!
Security Alert:
Using the Remote Module gains access to the features of
the DEFINITY ECS, including access to WATS lines, FX
lines, etc., which are subject to toll fraud. Guard passwords
carefully!
Equipment List
Your Remote Module package should include:
■
One Remote Module (identified on the top of the unit)
■
One 7-foot standard telephone line cord
■
One AC adapter
®
■
DEFINITY Extender Remote Module User's Guide
NOTE:
A DEFINITY telephone and its associated telephone cord are
not supplied with the Remote Module and must be ordered
separately. Contact your system administrator or Lucent
Technologies representative for information. The Switch
Module(s) is also ordered and shipped separately.
Issue 2 July 1997 1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
You must supply the following for installation:
■
■
■
■
DEFINITY ECS display telephone
Telephone cord
If you use an 8434D telephone, an MSP-1 power supply
If you are connecting the Remote Module to a 240-vac outlet,
an adapter to convert to 120 vac.
■
Power and central office line suppressor. Lucent Technologies
recommends the 147C AC/CO Line Surge Protector (#8310-
006). Contact your Lucent Technologies representative for
ordering instructions.
NOTE:
Save your packing materials. Even though the Remote Module is a
reliable product, it may be necessary to return it for maintenance.
When returning the module, use the original package.
1-4 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Compatibility
The DEFINITY Extender is compatible with the following
commercial two-wire DEFINITY ECS display telephones.
■
8410D
■
8434D
NOTE:
The power supply that comes with the DEFINITY Extender
Remote Module cannot produce the power required by the
8434D telephone. An MSP-1 (WP924644) power supply must
be used. Check with your Lucent Technologies representative
for ordering information.
■
603 E Callmaster III
NOTE:
A telephone identical to the 8410D but certified for residential use
is being designed. This telephone will be available in the near
future. Contact your Lucent Technologies representative for
information and availability dates.
Options
You can order a wall-mounted metal bracket with a slide-in style
sleeve for use with the Remote Module. Contact your Lucent
Technologies representative for ordering information.
Issue 2 July 1997 1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Specifications
The DEFINITY Extender system should operate properly with any
standard telephone service (also called “plain old telephone
service” [POTS] line). Line conditioning may be required if the
Switch and Remote Modules do not connect at a data rate of
19.2 kbps.
Table 1-1 shows the specifications of the DEFINITY Extender
Remote Module.
NOTE:
Specifications are subject to change without notice as technological
or manufacturing changes warrant.
1-6 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Table 1-1. Remote Module Specifications
Specification
Description
Size
8.0" x 8.0" x 1.50"
(205 mm x 205 mm x 40 mm)
Weight
1.5 pounds (0.68 kilograms)
Power Requirements
12 vdc supplied by 120-vac adapters.
800 mA maximum
Communication
Data Type
V.32terbo modem
600 Ohms
Data Impedance
Data Tx Level
Data Rx Sensitivity
User Data Port
Data Type
–15 dBm (+1 dBm/–3 dBm)
–40 to 0 dBm
RS-232
Data Rate Setting
19.2 kbps/9.6 kbps, no parity, 8 bit,
1 stop bit
Issue 2 July 1997 1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Considerations
Keep the following in mind when you use the DEFINITY Extender
system:
■
The DEFINITY Extender system is to be used with a DEFINITY
ECS of Version 3, Release 3 or later.
■
No custom calling features, such as Call Waiting or Call
Forwarding, should be ordered for the line to which you connect
the Remote Module.
NOTE:
A Call Waiting tone causes an interruption in the call, and the
Remote Module will begin the reconnect sequence.
■
Use of the speakerphone on the DEFINITY telephone
connected to the Remote Module will degrade voice quality.
■
When you use voice and data simultaneously on the Remote
Module, the voice transmission will have priority over the data
transmission.
■
Sessions can be established only from the Remote Module.
■
Authorized connections require a password 8 to 10 digits in
length.
1-8 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
!
Security Alert:
Using the Remote Module gains access to the features of
the DEFINITY ECS, including access to WATS lines, FX
lines, etc., which are subject to toll fraud. Passwords should
be as long as allowed. Passwords should be hard to guess
and therefore should not contain:
■
all the same numbers (for example, 88888888)
■
sequential characters (for example, 987654321)
■
character strings associated with you or with your
business. These include:
—
—
—
—
—
Names
Birthdays
Business name
Telephone number
Social security number
■
Words and commonly used names
Passwords should use as wide a variety of characters as
possible. Passwords should be changed regularly, at least
on a quarterly basis. Do not recycle old passwords.
Issue 2 July 1997 1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2
®
How to install the DEFINITY Extender Remote Module
Installing the Remote Module involves choosing a proper location and
plugging in the LINE, PORT, and power cords.
Issue 2 July 1997 2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Location Requirements
To ensure successful operation of the DEFINITY Extender system,
place the Remote Module within 400 feet (120 meters) of the
DEFINITY telephone. The Extender module may be mounted in
any position or may be wall-mounted by using the optional wall-
mount bracket. Install the module's power supply and cabling away
from high-power/high-RF noise devices such as computers, fans,
fluorescent ballasts, and power supplies.
Electrical Requirements
Use only the AC adapters provided with the DEFINITY Extender
system. The Extender has been designed to operate from 120 vac
60 Hz.
!
CAUTION:
Do not apply power to the Extender module until specifically
instructed in the installation procedures.
2-2 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting the Remote Module
All connections to the Remote Module are done via the back panel
(see Figure 2-1). Presently no ports are installed for VOICE or
COM 2. The current back panel elements are:
■
LINE is the connection between the Remote Module and the
central office line for transmission of the signaling information to
the Switch Module.
■
PORT is the connection between the DEFINITY telephone and
the Remote Module.
■
COM 1 provides for simultaneous RS-232 communication
between equipment at the off-premise site and equipment at
the on-premise site.
■
COM 2 is reserved for future use
■
+12VDC is the connection for the A/C adapter.
■
The DIP switch under OPT is used for system configuration.
Figure 2-1. Remote Module Back Panel
Issue 2 July 1997 2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
In addition to the back panel connections, a three-color light-
emitting diode (LED) is visible through the top of each unit and
provides information about the status of the equipment.
Installation Procedure
Installing the Remote Module involves connecting the line cords,
the telephone cord, the power cord, and, at your option, the
RS-232 cable. The line cord and power cord are supplied with your
Remote Module, and the telephone cord and any power cords
required for the operation of the telephone are supplied with the
display telephone.
Follow these steps to install the Remote Module:
!
CAUTION:
Do not plug the A/C adapters into the electrical outlets until
instructed to do so in the following procedure.
1. Ensure that the module has the proper DIP switch configuration
(see Table 2-1).
2-4 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Table 2-1. DIP Switch Configuration
Switch #
OFF
ON
1
2
3
4
Normal operation
Normal operation
Normal operation
Normal operation
Reserved
Dedicated lines
Reserved
Test mode
NOTE:
If you are using a standard central office line, you do not have to
change the factory-set DIP switches. Check with your system
administrator before making any changes. Your system
administrator may have changed DIP switch 3 to the ON
position for normal operation. Do not change this setting without
contacting your system administrator.
2. Connect one end of the line cord provided with the Remote
Module to the telephone company phone jack and the other end
to the LINE jack of the Remote Module.
3. Connect the DEFINITY telephone to the PORT jack of the
Remote Module by using the cord provided with the telephone.
!
CAUTION:
Do not plug the line cord provided with the Remote Module
into the PORT jack of the Remote Module. Damage to
circuits may result.
Issue 2 July 1997 2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
4. Connect the AC adapter provided with your system to the
Remote Module. Plug the adapter into a standard 120-vac
electrical outlet.
!
CAUTION:
Do not plug the A/C adapters into a 240-vac outlet because
you will damage the adapter and the module. You must first
obtain an adapter to convert 240 vac to 120 vac.
5. The display on the telephone will initialize and read “Go
Online?”
Connections for Data Transmission
By using the COM 1 port on the Remote Module, you can establish
simultaneous data transmission between the off-premise location
and the on-premise location. Typically this involves a personal
computer (a “remote data terminal”) at the off-premise location
communicating with an RS-232 server link on-premise (at the
DEFINITY ECS location).
You will need two straight-through, 9-pin RS-232 cables to
establish data transmission.
Connect the data terminal at the remote location to the COM 1 port
of the Remote Module by using the straight-through cable (see
Figure 2-2).
2-6 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Figure 2-2. RS-232 Cable Pin Connections
NOTE:
The DEFINITY Extender modules use the CTS line for flow control.
When the internal buffer is 32 characters from full, the CTS line is
turned off. While CTS is off, up to an additional 32 characters can
be transmitted without any loss of data. If hardware flow control is
not enabled or if a cable without the CTS line connected is used,
characters will be lost when this buffer overflows.
The DEFINITY Extender modules use the DCD line to indicate
whether or not the modules have made a connection. When this
line is on, the modules have made connection.
Issue 2 July 1997 2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
3
®
How to program the operating parameters for the DEFINITY
Extender Remote Module
Before you can use the Remote Module, you must program the
operating parameters, such as the phone number, the type of dialing,
and the baud rate of communication.
Issue 2 July 1997 3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Using the Telephone for
Programming
Use the DEFINITY telephone to program the operating parameters
at the remote location. Prompts will appear on the telephone
display. To respond to the prompts, press the dial pad keys on the
telephone. Table 3-1 shows the keys used to move to or select
programming options.
Table 3-1. Telephone Keys Used in Programming
Telephone Key
1
Function
Allows user to move backward through
programming menu.
2
3
Allows user to select a parameter for
programming.
Allows user to move forward through
programming menu.
After you connect your Remote Module and DEFINITY telephone,
the following will appear on the telephone display:
3-2 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
To begin programming, press 3 until the first parameter (“Set
Phone Number?” ) is shown on the display. If your system
administrator preprogrammed your Remote Module, press 2 to
begin system operation (see Chapter 4, Operating the DEFINITY
Extender.)
Setting the Telephone Number
If your Remote Module is connected to a standard telephone line, a
telephone number to dial must be programmed for proper
operation. If your system administrator has not preprogrammed this
telephone number for your Remote Module, follow the steps and
screens below to set the telephone number on the module. The
following screen appears only if the module is configured for dial
line operation (DIP switch 2 is OFF). This parameter programs the
telephone number used to call the Switch Module. Ask your system
administrator for the telephone number to program.
1. Press 2 to select this parameter, or press 3 to advance to the
next programming option. If you select 2 , either a screen
appears showing the current stored number or a blank screen
appears if no number has been programmed.
2. To change an existing number or to enter a new number, dial
the required digits by using the telephone keys (0 to 9).
3. Press the Drop button on the display telephone to accept the
number and return to the main menu.
Issue 2 July 1997 3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Setting the Mode of Dialing
The options for the mode of dialing (tone or pulse) appear only if
the Remote Module is configured for dial line operation (DIP switch
2 is OFF).
Setting Pulse Dialing
Follow these steps to set the mode of dialing to pulse:
1. At the “Go Online?” screen, press 3 until the following screen
appears:
2. “Set Pulse Dialing” indicates that TONE dialing is presently
activated (factory default). If you want to switch to PULSE
dialing, press 2 . The following screen appears:
3. Press 2 to accept the change or 1 to cancel the request.
3-4 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Setting Tone Dialing
Setting the dialing mode to “Tone” is very similar to setting it to
“Pulse.” Follow these steps to set the dialing mode to tone.
1. At the “Go Online?” screen, press 3 until the following screen
appears:
2. “Set Tone Dialing” indicates that PULSE dialing is presently
activated. If you want to switch to TONE dialing, press 3 . The
following screen appears:
3. Press 2 to accept the change or 1 to cancel the request.
Issue 2 July 1997 3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Setting the Connect Rate
Setting the Connect Rate establishes the baud rate in kilobits per
second (kbps) for the communications between the Switch and
Remote Modules. Follow the steps and screens below to set the
Connect Rate.
1. At the “Go Online?” screen, press 3 until the following screen
appears:
2. Press 2 to change the connect rate. The following screen
appears:
3. Press 3 until the Connect Rate you want appears. There are
six choices:
■
Auto—(Factory default). When the auto setting is selected,
the module tries to connect at the speed that will provide
the best performance with the fewest errors. The speed will
vary depending on line performance. If the module is
unable to connect at any of the available speeds, an error
message appears.
■
F-- —The Remote Module will connect at 19.2 kbps only,
the fastest rate.
3-6 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
■
FM- —The Remote Module will connect at 19.2 or 16.8
kbps.
■
■
-M- —The Remote Module will connect at 16.8 kbps only.
-MS —The Remote Module will connect at 16.8 or 14.4
kbps.
■
--S —The Remote Module will connect at 14.4 kbps only,
the slowest rate.
NOTE:
In some situations, selection of a slower connect rate may
result in a more reliable connection. The higher the connect rate
you choose, the greater is the possibility of data errors. When a
high number of data errors is detected, your call connection
may be interrupted while the Remote Module attempts to
reconnect. When this happens, you and your caller will hear a
beep followed by a message (called the “retrain” prompt):
Please remain on the line. This call is
experiencing technical difficulties. Your call will
resume momentarily.
After this message, you and your caller will hear a second beep.
The call is restored immediately after the second beep.
NOTE:
If the line problems cause the call to completely disconnect, you
and your caller will hear the following message:
We are (still) experiencing technical difficulties on this
call. We apologize for this inconvenience. If you
initiated this call, please hang up and place your call
again.
Issue 2 July 1997 3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
In this situation, the Remote Module tries to reconnect with the
Switch Module a maximum of six times. If the connection with
the Switch Module is not re-established after the sixth try, the
modem disconnects and you must log in again.
4. To view the next Connect Rate, press 3 ; to view the previous
Connect Rate, press 1 . Press 2 to accept the Connect Rate
displayed.
Setting the COM Port Baud Rate
You must set the baud rate for the COM 1 port on the Remote
Module. This is the rate at which data will be transmitted to and
from your remote terminal device, usually a computer. Two rates
are available: 19.2 kbps and 9.6 kbps. Follow these steps to set the
rate for the COM 1 port:
1. At the “Go Online?” screen, press 3 until the following screen
appears:
2. Press 2 to get the Comm Port rate. If 9600 kbps is in effect, the
following screen appears:
3. Press 2 to change the setting or 1 to retain the existing setting.
3-8 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
4. If 19.2 kbps is in effect, the following screen appears:
5. Press 2 to change the setting or 1 to retain the existing setting.
NOTE:
If your are talking on your display telephone while transmitting data
via the COM port, there is not much difference in speed between
9.6 kbps and 19.2 kbps. However, if you are transmitting data only,
the 19.2 rate will be significantly faster.
Exiting Programming
To exit the programming mode, press 1 until the following screen
appears:
Issue 2 July 1997 3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Remote
Module
4
Operating the Remote Module of the DEFINITY Extender
Once you have installed and programmed the Remote Module, you
are ready to use it. After you have established a connection with the
Switch Module (and consequently the DEFINITY ECS), you can use
your DEFINITY telephone as you would any other telephone on the
system.
Issue 2 July 1997 4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Remote Module
Starting the Operation
You start the operation of the Remote Module by a process similar
to logging in on other systems. Follow these steps to start the
operation of the Remote Module:
1. At the “Go Online?” screen, press 2 to start the operation of the
DEFINITY Extender system.
2. At this point, the Remote Module dials the Switch Module at the
programmed number (see “Setting the Telephone Number” in
Chapter 3, Programming). Figure 4-1 shows the sequence of
messages that appear on the telephone display during
connection of the Extender system.
4-2 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Remote Module
Figure 4-1. Connect Sequence for the Remote Module
3. At the “Enter Password” screen, enter your password and press
the Drop button on the display telephone. A valid password
must be entered to allow the telephone to be connected to the
PBX.
Issue 2 July 1997 4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Remote Module
NOTE:
You must enter your current valid password. The first time you
use your Remote Module, the password will be the one initially
assigned to you by your system administrator. A valid password
contains 8 to 10 digits.
4. If a valid password has been entered, the Remote Module
completes the connect sequence and the telephone will be
operational. If an invalid password has been entered, you will be
prompted to re-enter the password. If after three attempts a
valid password has not been entered, the Remote Module will
disconnect and the “Go Online?” prompt will be displayed.
Check your current password with your system administrator;
as necessary, reset your password and repeat the procedure
from Step 1.
Disconnecting
To discontinue operation of the DEFINITY Extender system, follow
these steps:
1. Press the Hold button on the display telephone four times. This
screen appears:
2. This “Disconnect” screen allows you to change your mind
before totally disconnecting. To disconnect, press 2 . The
disconnect sequence appears on the display; after a few
seconds the “Go Online?” screen appears. This indicates you
are disconnected.
4-4 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Remote Module
!
CAUTION:
Be sure that you have completely logged off by waiting for
the “Go Online?” screen to appear. If you do not completely
log off, the Remote Module may continue to try to re-
establish the connection, and you will be liable for any
applicable toll charges incurred.
3. If you do not want to disconnect, press 3 at the “Disconnect”
screen. The following screen appears:
4. Do one of the following:
■
Press 1 to return to the “Disconnect” screen and disconnect
the system. The “Go Online?” screen appears, indicating
that the DEFINITY Extender system is no longer connected.
■
Press 2 to retain connection.
■
Press 3 to go to the Change Password screen.
Issue 2 July 1997 4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Remote Module
Changing a Password
Follow these steps to change your password.
1. If you are not connected to the PBX, follow the steps in “Starting
the Operation” above to connect to the PBX.
2. Once you are connected, press the Hold button on the display
telephone four times and the following screen appears:
3. Press 3 and the following screen appears:
4. Press 3 and the following screen appears:
4-6 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Remote Module
NOTE:
If you press 3 and the “View S/W Version” screen appears,
check with your system administrator. This indicates that you
cannot change your own password.
5. Press 2 change a password. You will be prompted to enter the
old password (a * will appear for each digit entered).
6. If the old password is correct, a prompt for the new password
appears. Enter the new password (8 to 10 digits). Be sure the
new password includes the first two digits of your old password.
The first two digits identify your user number.
If the old password is not correct, the message “Invalid
Password” appears and you are returned to the “Change
Password?” screen. Check your password, and repeat Step 5.
If you continue to have problems, check with your system
administrator.
Issue 2 July 1997 4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Remote Module
!
Security Alert:
Using the Remote Module gains access to the features of
the DEFINITY ECS, including access to WATS lines, FX
lines, etc., which are subject to toll fraud. Passwords should
be as long as allowed. Passwords should be hard to guess
and therefore should not contain:
■
all the same numbers (for example, 88888888)
■
sequential characters (for example, 987654321)
■
character strings associated with you or with your
business. These include:
—
—
—
—
—
Names
Birthdays
Business name
Telephone number
Social security number
■
Words and commonly used names
Passwords should use as wide a variety of characters as
possible. Passwords should be changed regularly, at least
on a quarterly basis. Do not recycle old passwords.
7. Re-enter the new password at the prompt. Press the Drop
button on the display telephone to accept the password.
4-8 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Remote Module
NOTE:
The system administrator (user 0) can change all user passwords
(see “Changing Passwords” in the “Programming” chapter in the
®
DEFINITY Extender Switch Module User's Guide). The remaining
users can change only their own passwords (user 1 can change
only the password which begins with 01). The new password also
must begin with 01).
NOTE:
In some cases your system administrator may have disabled your
ability to change your password. Check with your system
administrator if you have problems.
Checking System Software
You can check the system software version used for the Switch
Module and the Remote Module. Follow these steps to check the
software version.
1. If you are not connected to the PBX, follow the steps in "Starting
the Operation" above to connect to the PBX.
2. Press the Hold button on the display telephone four times, and
the following screen appears:
Issue 2 July 1997 4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Remote Module
3. Press 3 until the following screen appears:
4. Press 2 and the following screen appears:
5. The Switch version screen follows directly:
4-10 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
5
Troubleshooting, LED Activity, and Error Messages
As with all equipment of a sophisticated nature, occasionally an error
in connection or transmission may occur. The DEFINITY Extender
system provides indication of any errors via light-emitting diodes
(LEDs) on the Remote and Switch Modules and by error messages on
the display telephone connected to the Remote Module.
Issue 2 July 1997 5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
When an error occurs in the operation of the Remote Module, you
should check for malfunctions in an organized manner. Follow
these steps when troubleshooting the Remote Module:
1. Verify that the programmed telephone number is correct.
2. Check all interconnecting cables to ensure that they are
properly seated.
3. Verify that the DIP switches are set correctly.
4. Check the circuits to ensure that they are free of noise and
meet the specifications listed in Chapter 1, Introduction.
5. Verify that the power LEDs are illuminated.
6. If you cannot locate the source of the problem, contact your
system administrator and describe the problem.
5-2 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
LED Sequences
The following flash sequences may be observed on the Remote
Module:
■
1 Green: Online to Switch Module
■
2 Green: Waiting for dial tone
■
3 Green: Dedicated Line mode connect sequence
■
4 Green: Dial mode connect sequence
■
5 Green: Program mode (entering parameters)
■
2 Red: Waiting for telephone connection
■
3 Yellow: Test mode
Error Messages
If a problem has been encountered during the connection process,
an error message will appear on the display telephone. Table 5-1
shows the error messages and the suggested actions to take.
Issue 2 July 1997 5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Table 5-1. Error Messages
Message
Cause
Action
No Dial Tone
The Remote Module Connect a regular
is not properly
connected to the
local telephone
company.
telephone to the
telephone company jack,
and listen for dial tone.
Make sure the line is
properly connected to the
jack on the Remote
Module. If you still do not
hear dial tone, contact
your system
administrator.
Line Busy
The line that the
Switch Module is
connected to is
already in use.
Contact your system
administrator, and verify
that the correct
telephone number has
been programmed and
that no one else is using
the Switch Module you
are trying to call.
No Answer
Tone
The Switch Module
is not responding.
Report the problem to
your system
The Remote Module administrator, and verify
does not receive a that the correct
Ring-Back tone or an telephone number has
Answer Back tone.
been programmed.
Continued on next page
5-4 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Table 5-1. Error Messages—Continued
Message
Cause
Action
Rate Too Slow The rate at which the Ensure that no other
modem is equipment is connected
connecting is not fast to the line. Report the
enough to allow for problem to your system
successful operation administrator.
of the system.
Issue 2 July 1997 5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
+12 vdc
12 volt direct current.
120 vac
120 volt alternating current (North American standard electrical supply).
B
Baud Rate
The speed in kbps at which digital data can be transmitted.
D
Direct Line
A dedicated circuit or private leased line.
Dedicated Subscriber Lines
Communication lines (usually twisted pair) that are used to connect on-
premise telephone equipment (such as a PBX) to the Central Office. Also
referred to as direct lines.
Issue 2 July 1997 GL-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Dial Line
A telephone line which is part of the Public Switched Telephone Network
and is accessed through the DEFINITY Extender’s automatic dial-up
function.
F
Facility
Transmission facilities. Usually a two metallic pair set of cords, but can be
Telco carriers, T-1, microwave or dial-up telecommunications lines.
L
LED
Light-emitting diode. A semiconductor diode which emits light when a
current is passed through it, indicating that the power is on.
O
On-premise Lines
Communication lines (usually twisted-pair) that are used to connect the
PBX to the DEFINITY telephone.
GL-2 Issue 2 July 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
P
PBX
Private Branch Exchange.
R
Remote Module
The DEFINITY Extender module that connects to the remote DEFINITY
telephone.
S
Switch Module
The DEFINITY Extender module that connects to the DEFINITY PBX.
Issue 2 July 1997 GL-3
Download from Www.Somanuals.com. All Manuals Search And Download.
|
