Lucas Control Systems
Deeco Systems
EM-C061
14" Flat Panel Display
Embedded Computer Module
USER MANUAL
Manual P/N: 15062
Manual Revision: 1.0
Manual Revision Date: June 1997
Download from Www.Somanuals.com. All Manuals Search And Download.
How to contact Deeco Systems for sales or technical support:
Lucas Control Systems, Deeco Systems
31047 Genstar Road
Hayward, California USA 94544-7831
Phone: 1-800-376-1154 or 510-471-4700
FAX: 510-489-3500
Technical Support BBS: 510-471-5402
Baud Rate:
Data Bits:
Parity:
Stop Bits:
Flow Control:
Emulation:
up to 14400 Baud
8
None
1
XON/OFF
ANSI
Europe Phone: 49-7024-9712-14
Europe FAX: 49-7024-9712-40
For Returns - Contact Deeco Systems’ customer service for a Return Authorization (RA)
number prior to shipping product to the factory. Freight to the factory is prepaid by the
customer. Freight return to the customer is paid by Deeco Systems. Ship product in its original
packaging or equivalent to prevent transit damage.
Copyright 1997, Lucas Automation and Control Engineering, Inc. (L.A.C.E., Inc.)
All rights reserved. Deeco is a registered trademark of LACE, Inc. All other trademarks are the property of
their respective owners. Information furnished by Deeco Systems is believed to be accurate and reliable.
However, no responsibility is assumed by Deeco Systems for its use, nor for any infringements of patents or
other rights of third parties which may result from its use. No license is granted by implication or otherwise
under any patent rights of LACE, Inc.
Printed in the USA.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning!!
Grounding circuit continuity is vital for safe operation of the machine.
Never operate the machine with the grounding conductor disconnected.
See installation instructions before connecting to the supply.
The computer system contains voltages capable of producing a dangerous
electrical shock. Only properly trained and authorized personnel should
access the computer.
CAUTION: DISCONNECT POWER BEFORE SERVICING.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
1.0 OVERVIEW............................................................................................................................. 1
1.1 PRODUCT SUMMARY............................................................................................................ 1
1.2 INDUSTRIAL COMPUTERS ................................................................................................... 2
1.3 SINGLE BOARD COMPUTER ................................................................................................ 2
1.4 ORDERING INFORMATION.................................................................................................... 3
1.5 SPECIFICATIONS ................................................................................................................... 5
1.6 DISPLAY.................................................................................................................................. 6
2.0 INSTALLATION .................................................................................................................... 7
2.1 UNPACKING ........................................................................................................................... 7
2.2 MOUNTING............................................................................................................................. 8
2.3 APPLYING POWER................................................................................................................. 8
2.4 POWER REQUIREMENTS....................................................................................................... 9
3.0 SINGLE BOARD COMPUTER OPERATION ................................................................... 11
4.0 TOUCH SYSTEM................................................................................................................. 13
5.0 INPUT/OUTPUT INTERFACE PORTS............................................................................... 15
5.1 SERIAL COMMUNICATIONS PORT..................................................................................... 15
5.2 PARALLEL COMMUNICATIONS PORT............................................................................... 15
5.2.1 Port Address Selection....................................................................................................... 15
5.2.2 Parallel Port Connector .................................................................................................... 16
5.3 KEYBOARD PORT................................................................................................................. 17
5.4 NETWORK COMMUNICATIONS PORT............................................................................... 17
5.4.1 10 BASE-T Connector ....................................................................................................... 18
5.4.2 10 BASE-2 Connector........................................................................................................ 18
6.0 DATA STORAGE.................................................................................................................. 19
6.1 HARD DRIVES: ...................................................................................................................... 19
6.2 SOLID STATE DISKS: ........................................................................................................... 19
6.3 FLOPPY DRIVES.................................................................................................................... 19
7.0 GENERAL MAINTENANCE................................................................................................ 21
7.1 EFFECTS OF CHEMICALS ON THE OPTIONAL SEALED BEZEL/FILTER....................... 21
8.0 TROUBLESHOOTING......................................................................................................... 23
8.1 POWER SUPPLY .................................................................................................................... 25
8.2 TOUCH INTERFACE.............................................................................................................. 26
8.2.1 Controller Board.............................................................................................................. 26
8.3 DISPLAY................................................................................................................................. 27
i
Download from Www.Somanuals.com. All Manuals Search And Download.
8.4 SINGLE BOARD COMPUTER................................................................................................ 27
9.0 COMPONENT TEST PROCEDURE.................................................................................... 29
9.1 POWER SUPPLY..................................................................................................................... 29
10.0 COMPONENT INSTALLATION AND REMOVAL.......................................................... 33
10.1 TOUCH CONTROLLER BOARD.......................................................................................... 35
10.1.2 Installation ...................................................................................................................... 35
10.2 MEMORY REMOVAL AND INSTALLATION..................................................................... 35
10.2.1 SIMMs Removal............................................................................................................... 35
10.2.2 SIMMs Installation .......................................................................................................... 36
10.3 MICROPROCESSOR REMOVAL AND INSTALLATION.................................................... 37
APPENDIX A: MECHANICAL DRAWINGS ............................................................................ 39
A.1 EM-C061 COMPUTER FRONT VIEW................................................................................... 39
A.2 EM-C061 COMPUTER REAR VIEW ..................................................................................... 40
A.3 EM-C061 SIDE VIEW ............................................................................................................ 41
A.4 EM-C061 CABLING DIAGRAM............................................................................................ 42
A.5 EM-C061 PANEL CUT-OUTS AND MOUNTING GUIDE .................................................... 43
APPENDIX B: PRODUCT NAMING CONVENTION.............................................................. 45
LIMITED WARRANTY.............................................................................................................. 47
INDEX .......................................................................................................................................... 49
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
1.0 Overview
Lucas Control Systems, Deeco™ Systems offers a complete line of rugged computers, VGA
monitors, and terminals. These products are available in sealed standalone enclosures, with panel
mount brackets, and as embedded modules. All Deeco Systems products are available with touch
systems for a complete user interface. Deeco Systems has manufactured quality flat panel display
based products for harsh and industrial applications for more than a decade.
The EM-C061 embedded computer module is an industrial Pentium®-based PC with a color TFT
LCD 13.8" flat panel display. The computer can be 19″ rack-mounted or easily integrated into panel
cut-outs or OEM equipment. The EM-C061 is available with a resistive touch screen system that
functions as a touch mouse.
1.1
PRODUCT SUMMARY
•
100, 133, 166 or 200 MHz Pentium processor.
•
Available with a high
resolution resistive touch
system. Touch mouse software
lets your finger work like a
mouse. Performs under the
most extreme conditions and
responds accurately -- even
when the operator is wearing
gloves.
•
Optional NEMA 4/12 (IP65)
sealed bezel available.
Optional panel mount frame
simplifies NEMA 4/12 (IP65)
seal to enclosure.
•
•
Color XGA AM TFT flat panel display
Optional rugged hard drive up to 3.26GB 3.5″ SCSI3 or 2.11GB Ultra SCSI, and 2.0 rugged
2.5″ PIO4 (EIDE) -- (SCSI drives require one PCI card slot).
•
•
•
Optional PC/104 Semiconductor Disk from 2 - 8MB.
Optional Ethernet - 10 BASE-T and 10 BASE-2.
Four full size ISA card slots or 2 PCI and 2 ISA card slots available (Note: One PCI slot is
needed for SCSI controller if SCSI hard drive is installed.)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
1.2
INDUSTRIAL COMPUTERS
Deeco computers are designed for industrial conditions and exposure to harsh environments
including extended high and low temperatures, high and low humidity, and severe shock and
vibration. The optional sealed front bezel meets NEMA 4/12 (IP65) requirements.
Deeco computers are available with Deeco’s Power Assist factory automation software, which
speeds implementation of the EM-C061 in industrial control applications. Experienced Applications
Engineers are available to help customers integrate computers into special situations.
The EM-C061 is available with integrated 13.8" AM color TFT LCD with XGA resolution (1024 x
768) and up to 4K colors.
The systems are available with resistive touch system and touch mouse software. These allow the
operator to establish mouse control directly from the display by pointing and dragging a finger over
the display. Modified mouse drivers are loaded in the hard disk at the factory. These enable the
user’s finger to emulate a standard mouse. Available mouse drivers include MS-DOS/Windows™,
Windows 95, Windows NT, and OS/2.
1.3
SINGLE BOARD COMPUTER
The EM-C061 uses a Pentium-class 100% PC-AT compatible industrial single board computer
(SBC).
The SBC supports up to 64 MB of 72-pin SIMM DRAM, in increments of 4, 8, 16, 32 or 64 MB
configurations. The SBC comes with an integrated peripheral controller for floppy disks, up to 4
EIDE hard disks, two external serial ports (one if the touch option is ordered), and a bi-directional
parallel port. Also included is an on-board C&T 655xx 32-bit CRT/LCD controller.
All DOS-based software, Windows 3.1, Windows 95, Windows NT, Novell NetWare, UNIX, and
OS/2 are supported. Software can be ordered pre-installed.
Power-up self-test diagnostics, a programmable watchdog timer, and Green PC energy management
are standard features of the EM-C061.
Detailed information and specifications for the Single Board Computer are in the separate SBC
manual.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
1.4
ORDERING INFORMATION
Base System Configuration
Select a Computer and Chip Set *a
❏ 123
❏ 120
❏ 121
❏ 122
Full Size ISA/PCI SBC, 100 MHz Pentium
Full Size ISA/PCI SBC, 133 MHz Pentium
Full Size ISA/PCI SBC, 166 MHz Pentium
Full Size ISA/PCI SBC, 200 MHz Pentium
Select Memory 72-Pin EDO SIMM
❏ 211
❏ 212
❏ 213
❏ 214
8MB SIMM
16MB SIMM
32MB SIMM
64MB SIMM
Select a Display
❏ 3261
XGA (1024 x 768) up to 4K colors, 13.8", AM Color TFT LCD
Upgrades and Options
Select a Power Supply *b
❏ 703
+20-36 VDC
❏ 704
90-264 VAC, 47-63 Hz
Select Input Device Option (select either or both)
❏ 416
14" Sealed Bezel, no touch
❏ 412
14" Sealed Bezel, resistive touch, controller
Backplane Expansion Option *c
❏ 1403
❏ 1404
4 slot ISA full-size backplane
2 PCI and 2 ISA full-size backplane
Mounting Option
❏ 1502
❏ 1503
Open Frame, Rack Mount
Open Frame, Panel Mount
Hard Drives *d
❏ 518
❏ 520
❏ 521
❏ 522
❏ 523
1.3GB, rugged 2.5" PIO4 (EIDE)
2.11GB, 3.5" Ultra SCSI (Requires PCI card slot)
3.26GB, 3.5" SCSI3 (Requires PCI card slot)
2.0GB, 2.5" rugged PIO4 (EIDE)
340MB, rugged 2.5" PIO4 (EIDE)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
Floppy Drive
❏ 600
Mounted Floppy Drive (Rear Access)
PC/104 Semiconductor Disks
❏ 1010
❏ 1011
2MB on PC/104 Card
8MB on PC/104 Card
Ethernet LAN Communications *e
❏ 904
10BASE-T (T-pair) / 10BASE-2
Software - Operating Systems
❏ 800
❏ 803
❏ 811
❏ 812
Microsoft Windows 3.1
DOS
Microsoft Windows 95
Microsoft Windows NT for Workstations
Software - Touch Drivers
❏ 816
❏ 817
❏ 818
❏ 820
DOS/Microsoft Windows 3.1
Microsoft Windows NT Resistive Touch Mouse
OS/2 Resistive Touch Mouse
Microsoft Windows 95 Resistive Touch Mouse
Software - Process Automation
❏ 807
❏ 808
❏ 814
❏ 819
Power Assist Developer Kit, DOS
Power Assist Run Time Kit, DOS
Power Assist for Windows-Developer
Power Assist for Windows-Run Time
Special Ordering Information
* a Includes video graphics chipset for 14” high resolution display.
* b If power supply not ordered user must provide +12VDC and +5VDC.
* c Requires option 703 or 704 power supply.
* d All disk drives are mounted to maximize shock and vibration requirements. SCSI hard disk drives require a PCI controller card,
which means the 1404 backplane option is required.
*e
Use PC/104 if backplane option is not chosen. ISA or PCI card will be used if backplane option has been selected.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
1.5
SPECIFICATIONS
CPU
Pentium processor up to 200 MHz
512K pipeline burst mode
L2 Cache
Displays
13.8" XGA (1024 x 768), AM Color TFT LCD
Chips and Technology 65XXX
Video Controller
Memory
Includes two to four 72-pin SIMM sockets supporting up to 128 MB DRAM
Connectors
Serial
Parallel
Network (optional)
Keyboard
Weight
26 lbs (11.82 kg)
Dimensions
(1502)
Standard
With Optional Front Panel
11.5" H x 14.4" W x 4.0" * D
(292 mm x 366 mm x 102 mm)
12.3" H x 15.2" W x 4.0" * D
(312 mm x 386 mm x 102 mm)
*Add 2.2" to depth for optional backplane.
Temperature
Operating Non-operating
o
o
o
o
0 C to +50 C
-25 C to +65 C
Shock (MIL-STD-810D) 10G
(tested with 2.5" HD)
50G
Vibration
(Broadband Spectrum
10-500 Hz per
1.0G rms
3.0G rms
MIL-STD-810D)
(tested with 2.5" HD)
Humidity
5% to 95% RH, non-condensing
Power Input
MTBF (nominal)
+24 VDC or 100-240 VAC input or +5V, +12V
SBC/controller > 80,000 hours
Display > 45,000 hours*
o
(@25 C)
*AMTFT display backlights are considered field replaceable items and are not included in MTBF figures.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
1.6
DISPLAY
The display is color active matrix LCD incorporating amorphous silicon TFT. Graphics and texts
can be displayed on the 1024 x 768 color panel. The TFT panel used is a low-reflection and higher-
color saturation type.
AMTFT technology is rapidly changing. The EM-C061 uses the latest technology in flat panel
displays.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
2.0 INSTALLATION
Read this section prior to installing the computer. Following these steps will ensure a successful
installation of the computer system.
2.1
UNPACKING
Components used in these systems are electrostatic sensitive. Observe proper electrostatic
discharge (ESD) procedures when unpacking and handling the computer.
The shipping configuration of the EM-C061 will vary according to the options ordered. The
following configuration is only a general guideline:
AC Power cord, +24VDC power cable, or pigtail for ±12 V, ±5V operation.
Serial cable with 2 9-pin DSUB connectors. If touch option is ordered, only one serial
connector (com1) is available for external use.
Single Board Computer manual.
Operating system software.
A panel mounting gasket if the panel mount option is ordered.
Touch Driver Diskette if touch option is ordered. The touch manual is on the diskette.
SSD Documentation if the SSD option is ordered
This User Manual.
Remove the computer from the protective wrapping and inspect the unit for any obvious damage
incurred during shipping. Contact the shipper if any damage is noted.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
2.2
MOUNTING
The EM-C061 is designed to be mounted in enclosures, rack-mounted, mounted in walls, and
integrated in systems. Other arrangements can be used as long as these standard criteria are met:
•
When the unit is safely mounted the installation must be able to support at least five times the
unit’s weight. The unit must be rigidly fastened so that when the touch screen is used the unit
will not move or fall over. The weight of the unit is 26 lbs (11.82 kg).
•
•
The mounting surface should not be a hot wall.
The unit should be mounted for optimum visibility of the display. Typically, this is at or slightly
above eye level. Avoid looking down on AM TFT displays from directly above, as the viewing
angle is not as good as in other planes.
•
Use the optional bezels or other transparent window to protect the display from impact.
Please refer to cut-out panel in Appendix A.
2.3
APPLYING POWER
Prior to applying power to the computer system the user should connect all peripheral equipment
including printers, Ethernet, external floppy drives, networks, etc. Refer to the section on I/O ports
for location information on peripheral connections. Once all associated equipment has been properly
connected, the user can make the power connection.
Once power is applied, the computer will run a series of system self tests. Upon completion of these
tests, the computer will open the operating system.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
2.4
POWER REQUIREMENTS
The following table specifies the electrical requirements and capabilities of the power supplies
available for the computer system.
Power Supply
Option
Voltage
20-36 VDC
100-240 VAC
+5
Current
6.7 - 3.7 A
1.25 - 2.5 A
8 A
Frequency
DC
Watts
100 W
100 W
40 W
Option 703
Option 704
47-63 Hz
DC
Customer
Supplied
±5, ±12V
-5
1 A
4 A
1 A
DC
DC
DC
5 W
48 W
12 W
+12
-12
Option 703 DC Supply:
Connect 20-36 V input power to the pigtail as shown:
24 VDC
Return
Ground
Option 704 AC Supply:
Connect 100-240VAC input power to the pigtail as shown.
Line
Neutral
Ground
9
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
Customer Supplied ±5, ±12V:
Connect ±5, ±12V and Ground to the pigtail as shown:
+5V
Ground
Ground
+12V
-12V
-5V
10
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
3.0 Single Board Computer Operation
The separate Single Board Computer (SBC) user manual contains setup, operation, and maintenance
documentation for the SBC. The SBC is factory configured by Deeco Systems, and modifications
are usually unnecessary.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
4.0 Touch System
Refer to the manual on the Touch Driver Diskette for information on the optional touch system.
Touch drivers are pre-installed at the factory and reside on the mass storage device.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
5.0 Input/Output Interface Ports
5.1
SERIAL COMMUNICATIONS PORT
The computer includes two serial ports, configured as COM1 and COM2. Refer to the SBC manual
for configuration information.
The EM-C061 includes a 12" cable with two 9-pin DSUB connectors, so customers can access the
two serial ports. COM2 is disconnected from the DSUB connector on the cable and used by the touch
screen when the optional touch screen is ordered.
Both serial connectors are PC standard male 9-pin DSUB connectors with the standard PC pin out:
Pin
I/O
Description
1
2
3
4
5
6
7
8
9
< I
< I
DCD
RX
> O
> O
TX
DTR
Gnd (Signal Ground)
< I
> O
< I
< I
DSR
RTS
CTS
RI
5.2
PARALLEL COMMUNICATIONS PORT
The SBC provides a fully compatible IBM AT bi-directional printer port.
5.2.1 Port Address Selection
By default, the printer port is configured as LPT1. Refer to the separate SBC User Manual for more
information.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
5.2.2 Parallel Port Connector
The parallel port uses a 25-pin IDC style DSUB. The pin out for the connector is:
Pin
Dir
Name/Description
-SROBE
PD0
PD1
PD2
PD3
PD4
PD5
PD6
Pin
Dir
O
I
O
O
-
Name/Description
-AUTOFD
-ERROR
-INIT
-SLCTIN
GND
GND
GND
GND
GND
1
2
3
4
5
6
7
8
9
O
14
16
16
17
18
19
20
21
22
23
24
25
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
-
-
-
-
-
-
-
PD7
10
11
12
13
-ACK
BUSY
PE
GND
GND
GND
I
I
I
SLCT
16
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
5.3
KEYBOARD PORT
The computer supports an AT style 101 Keyboard.
Keyboard Connector
(Rear View)
Pin
1
2
Signal
KeyClk
KeyData
NC
3
5
1
4
3
2
4
GND
5
VCC
5.4
NETWORK COMMUNICATIONS PORT
Ethernet is the most widely used of all LAN protocols. Typical characteristics of the Ethernet
are:
Bandwidth
Protocol
Frame Size
Max. Nodes
Max. Network Span
10 MB/Sec
CSMA/CD
1514 bytes
1024
2.8 Km
There are 3 basic topologies. Characteristics of each are shown below:
Media
10 BASE-T
Topology
STAR
Segment
100 Meters
Cable Connection
24 AWG, 100 ohm, 8 pin, RJ45
(Twisted Pair)
10 BASE-2
BUS
185 Meters
RG58, BNC ‘T’
(Multi-Point)
10 BASE-T is most popular because of its low cost and easy installation. Also, UTP’s star topology
allows the rest of the network to function correctly even if a break occurs in a particular segment.
Cable length is limited to 100 m for twisted pair wires.
The EM-C061 can be ordered with 10 BASE-T and 10 BASE-2 connectors. Both connectors are
available when the Ethernet option is ordered.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
5.4.1 10 BASE-T Connector
Ethernet Network Interface
RJ45 Connector Pin-Out
1 2 3 4 5 6 7 8
Front View
Pin
1
2
3
4
Signal
TX+
TX-
RX+
NC
5
NC
6
7
RX-
NC
8
NC
5.4.2 10 BASE-2 Connector
The 10 BASE-2 connector is a BNC type COAX connector.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
6.0 Data Storage
6.1 HARD DRIVES:
Drive Type
1.3GB, rugged 2.5″ PIO4 (EIDE)
2.0GB, rugged 2.5″ PIO4 (EIDE)
2.11GB, 3.5″ Ultra SCSI (Requires PCI card slot)
3.26GB, 3.5″ SCSI3 (Requires PCI card slot)
340MB, rugged 2.5″ PIO4 (EIDE)
The hard drive is preconfigured and preloaded with all software options at the factory.
6.2 SOLID STATE DISKS:
Refer to the separate SSD documentation shipped with the 2 MB or 8 MB SSD options.
6.3 FLOPPY DRIVES
Refer to the separate SBC manual for information on connecting a floppy disk drive.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
7.0 General Maintenance
The bezel and filter are made of a plastic polymer material, so strong solvents or acids should not be
used for cleaning purposes. A soft, lint-free cloth, along with a non-abrasive, non-acidic cleaner can
be used to clean the touch screen. Ammonia based cleaners are fine.
7.1 EFFECTS OF CHEMICALS ON THE OPTIONAL SEALED
BEZEL/FILTER
Chemical Resistance
The active area of the touch screen is resistant to the following:
Acetone
Butyl Cellosolve
Cyclohexanone
Ethyl Acetate
Hexane
Isopropyl Alcohol
MEK
Methylene Chloride
Toluene
Xylene
40% NaOH
Clorox
Coffee
Downy
Fantastik
Formula 409
Grape Juice
Ketchup
Lemon Juice
Mineral Spirits
Mr. Clean
Mustard
Spray'N'Wash
Tea
Tomato Juice
Top Job
Turpentine
Vinegar
Wisk
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
8.0 Troubleshooting
Lucas Deeco maintains a repair facility at the factory and at various international locations. Call
Technical Support and ask for a RA (return authorization) number before shipping computers
needing repairs. Use the telephone number in the front of this manual.
If the computer suddenly ceases to function, disconnect the power, and re-seat all the cables on their
connectors. Be careful to re-connect all the cables correctly.
Sometimes computer problems have simple, easy-to-correct causes. Before doing anything else,
carefully check these solutions/tips.
Power
•
•
•
Is your computer connected to a working wall outlet?
Is the power cord plugged firmly into the wall outlet and into the computer?
Is your computer turned on? Are the power lights illuminated?
Cables
•
Are all cables connected properly and securely?
Startup
•
Was the diskette drive empty when you started the computer? (If not, eject the diskette and try
restarting your computer.)
If all these have been checked and there is still a problem please see if the problem is listed below
and then check the appropriate sub-system.
Problem:
System does not boot, or boots improperly.
Sub-System to Check:
•
•
•
•
•
Fuse
Single Board Computer (Refer to the accompanying SBC manual)
BIOS system (Refer to the accompanying SBC manual)
Power Supply
Memory Systems
23
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
Problem:
Malfunctioning Display
Sub-System to Check:
•
•
•
Display
Single Board Computer Motherboard (Refer to the accompanying SBC manual)
Power Supply
Problem:
Malfunctioning Memory Systems
Sub-System to Check:
•
•
Single Board Computer Motherboard (Refer to the accompanying SBC manual)
BIOS System (Refer to the accompanying SBC manual)
Problem:
Mouse pointer unresponsive to touch
Sub-System to Check:
•
•
Mouse Drivers
Touch controller
Problem:
Serial, Parallel, External Floppy Drive, Keyboard I/O Malfunction
Sub-System to Check:
•
•
•
Single Board Computer (Refer to the accompanying SBC manual)
BIOS System (Refer to the accompanying SBC manual)
Cabling
If after following the appropriate troubleshooting guidelines you cannot determine the nature of the
problem, contact Deeco technical support.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
8.1
POWER SUPPLY
•
Input Power:
Check to see if the input power to the power supply meets the requirement in section 2.4 of
this manual. Refer to section 9.1 for power supply test procedures.
If the measured input power is not within the values shown, provide an alternative source of input
power to the computer that satisfies the proper input power requirements. If the measured power falls
within the values shown, proceed to the next troubleshooting guideline in section 9.1.
•
Output Power:
Refer to section 9.1 for procedures for testing the power supply output.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
8.2
TOUCH INTERFACE
3.3" (84 mm)
3.0" (76 mm)
E271-2210
ELOGRAPHICS, INC.
LED
P4
-
Power
1x2 M
+
RS-232 Serial
2x5 M
P2
P3
5
1
LYAccuTouch
S1x5 M
X
H
H1
J0 •1 2 3 4 5 6 7 8 9 10 11
0.15" (4 mm)
0.156" (4 mm)
8.2.1 Controller Board
•
Input Power:
Check to see if the input power to the controller board meets the specifications in the
following table.
Pin
Power
-
Ground
+
+5 VDC
If the measured input power is incorrect, refer to section 9.1 to test for possible power supply
malfunctions. If you are receiving correct power, move on to the next troubleshooting guideline.
•
Touch Frame Cables:
Ensure that the 5-pin touch frame cable is properly seated at header P3. If the touch problem
persists, move on to the next troubleshooting guideline.
SBC Interface Cable:
Ensure that the SBC Interface cable is properly seated at header J8 of the controller board.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
8.3
DISPLAY
Verify that the cable is properly connected to the SBC. Replace the cable as a part of test procedure.
If display still does not work contact application engineering or otherwise return the unit to the
factory.
8.4
SINGLE BOARD COMPUTER
Input Power:
Using the multi-meter, check to see if the input power to the SBC meets the voltage. Make sure
that power pins are not shorted during the measurements. Refer to the SBC manual for power
connector pinout.
If the measured input power is incorrect, refer to section 9.1 to test for possible power supply
malfunctions. If the motherboard is receiving correct power, move on to the next troubleshooting
guideline.
•
SBC Mounting:
Make sure that the solder side of the SBC is insulated from making contact with the case of the
computer system. Any shorting of the SBC can cause system failure and damage to the SBC.
•
•
Strapping Fields (Jumper Settings):
Refer to the accompanying SBC manual.
SIMMs:
Check the SIMMs to verify that they are properly installed. Missing or incorrectly aligned
SIMMs will prevent the SBC from operating. Refer to section 10.2 and the accompanying SBC
manual for details on proper installation procedures.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
9.0 Component Test Procedure
9.1
POWER SUPPLY
This section details the procedures for testing the functionality of the power supply.
Warning: The power supply produces DC voltages that can cause a severe electric shock if
handled improperly. Disconnect power before opening.
•
Input Power:
Plug the computer into the desired power source. The voltage should fall within this range at the
power supply input connector.
Option 703, @ connector J1
Option 704, @ connector J1
Pin
1
2
Power
Ground
- (Return)
3
+20 to +36 VDC
Pin
1
Power
Ground
2
Neutral
3
100-240 VAC at 47-63 Hz
If the measured input voltage is not within the values shown, send the unit back to the factory for
power supply replacement/repair.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
•
Output Power:
Using a multi-meter set for DC voltage, measure the potential between ground and the pins in
the following table. The voltage should match the values shown when the supply is loaded.
Supplies 703, 704
Pin
1
2
3
4
5
6
7
Function
+5 VDC
+5 VDC
+5 VDC
Ground
Ground
Ground
Ground
Pin
8
9
10
11
12
13
14
Function
+12 VDC
+12 VDC
NC
-12 VDC
KEY
-5 VDC
Isolated Return
30
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
If no output is measured, disconnect the power supply from source voltage and check the fuse on the
power supply board.
•
Fuse:
Remove the fuse from the power supply. Measure the resistance with an ohmmeter. If the
fuse is open, replace the fuse on the power supply.
Power Supply Order Number Description
Value of F1
703
704
+24 VDC 100W
100-240 VAC 100W
A/250 VAC, Fast Blow
2A/250 VAC, Fast Blow
Different suppliers may qualify as power supply vendors. Always match replacement fuses to
original fuses.
Warning:
For protection against fire replace the fuse only with the same type
and rating of fuse.
Some power supplies have axial fuse holders. Place a
screwdriver on the metal portion of the fuse, and
gently lift the fuse from the socket.
Some power supplies have fuse holders with round
caps. These fuse holders are sealed with a silicon
RTV type adhesive. Break the silicon seal. Use a flat
bladed screwdriver to gently open the top of the fuse
holder, then remove the fuse. Apply a suitable
adhesive to the fuse holder cap upon re-assembly to
preserve the computer’s shock and vibration
specifications.
Removing an Axial Power Supply Fuse
With a Screwdriver
(Photo used for illustrative purposes only. Models and configurations may vary.)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
10.0 Component Installation and Removal
Rear View
33
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
Right Side View
(Viewed from Front)
Left Side View
(Viewed from Front)
34
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
10.1 TOUCH CONTROLLER BOARD
10.1.1 Removal
•
•
•
•
•
Place the computer face-down on a flat surface.
Remove the 5-pin touch screen flex cable from P3 on the touch controller.
Remove the serial interface cable from the P2 header on the controller board.
Remove the 2-pin power cable.
Remove the 4 Phillips mounting screws holding the controller board to the side panel on the
computer chassis.
•
Remove the touch controller from the computer system.
10.1.2 Installation
To install the touch controller, simply reverse the order of the removal procedures specified in the
previous sections.
10.2 MEMORY REMOVAL AND INSTALLATION
Refer to the accompanying SBC User Manual for SIMM removal and installation.
10.2.1 SIMMs Removal
•
•
Place the computer face-down on a flat surface.
Gently press the retaining clips on each end of the SIMM socket outward until the SIMM comes
loose form the retaining tabs.
Gently pull the SIMM module out of the socket of the motherboard.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
10.2.2 SIMMs Installation
Figure A
Figure B
(Photo used for illustrative purposes only. Models and configurations may vary.)
•
•
Insert the SIMM at an angle as shown in Figure A. The SIMM will not physically fit in the
socket unless pin 1 of the SIMM matches pin 1 of the socket.
Gently press the SIMM into the vertical position. The SIMM will snap easily into place if the
connectors are at the correct depth in the socket.
Refer to the SBC manual for memory configuration requirements.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
10.3 MICROPROCESSOR REMOVAL AND INSTALLATION
Chip Removal Tool
Removing the microprocessor from the socket
(Photo used for illustrative purposes only. Models and configurations may vary.)
Refer to the accompanying SBC User Manual for microprocessor removal and installation
guidelines. Make sure the jumper settings are matching the CPU speed!
The heatsink is glued to certain microprocessors. Consult the factory for replacement
microprocessors with similar heat sinks.
Use a special IC replacement tool to remove the microprocessor from the socket
When replacing the microprocessor, note the bevel on one corner of the IC. This designates pin 1.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
Appendix A: Mechanical Drawings
A.1
EM-C061 COMPUTER FRONT VIEW
11.5"
(292 mm)
14.4" (366 mm)
Note: Dimensions shown without optional front panel.
with front panel are 12.3" H x 15.2" W (312 mm x 386 mm)
Drawing not to scale -- Dimensions are in inches (mm).
39
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
A.2
EM-C061 COMPUTER REAR VIEW
SBC in Standard Model
Card Slots (2 PCI, SBC, 2 ISA slots or 4 ISA slots) with Backplane Option
14.4" (366 mm)
11.5"
(292 mm)
Power
Supply
Touch
Controller
Hard Drive / Floppy Drive
Drawing not to scale -- Dimensions are in inches (mm).
40
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
A.3
EM-C061 SIDE VIEW
2 PCI Slots
2 ISA Slots
SBC
11.5"
(292 mm)
Power Supply
Hard Drive
Floppy Drive
4.0" (102 mm)
without backplane
6.2" (157 mm)
with backplane
Drawing not to scale -- Dimensions are in inches (mm).
41
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
A.4
EM-C061 CABLING DIAGRAM
Touchscreen
Display
Touch
Controller
Floppy Disk Drive
FDD Option
SBC
IDE HDD
IDE HDD Option
COM1
COM2
LPT1
SCSI HDD
SCSI
Controller
KYBD
SCSI HDD Option
42
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
A.5
EM-C061 PANEL CUT-OUTS AND MOUNTING GUIDE
11.22" (284.99 mm)
0.09" (2.29 mm)
Suggested Panel Cutout for Mounting
the EM-C061 Computer
without the optional front panel
8.38" (H) x 11.22" (W)
(212.85 mm x 284.99 mm)
5.29" (134.37 mm)
0.32"
(8.13 mm)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
14.50" (368.30 mm)
0.15"
(3.81 mm)
0.11" (2.80 mm)
Suggested Panel Cutout
for Mounting the
EM-C061 Computer
with the optional front panel
11.60" (H) x 14.50" (W)
( 294.64 mm x 368.30 mm)
Center Line
0.15"
(3.81 mm)
2.5"
(63.50 mm)
2.5"
(63.50 mm)
7.25" (184.15 mm)
7.25" (184.15 mm)
Center Line
44
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
Appendix B: Product Naming Convention
EM - C 0 6 1
Platform Type
ST Enclosed System
EM Embedded Module
Processing Configuration
Designator:
Computers
Terminals
Monitors
0
1
2
- *
-
486
Pentium
C9
-
-
Receiver Card Bus Card
Functional Type
Display Size
C
T
M
Computer, CPU-based
Serial Terminal
Monitor system
1
2
3
4
5
6
7
NA
8.4″
10.4″
11.3″
12.1″
13.8″
17.7″
Case Style
0
1
2
3
4
5
6
No case
Rack mount
Medium Sealed Enclosure
Swivel Housing
Panel Mount Housing
Large Sealed Enclosure
Small Sealed Enclosure
Examples
ST-C461
EM-C031
Sealed Computer, Medium case, 10.4″ display, Pentium SBC
Embedded computer, 10.4″ display, Pentium SBC
*This refers to the type of CPU that the model was designed for but others CPUs may be substituted.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
Display Nomenclature
3 f d s
Sequential number ID
Size of display (same as specified in base unit ID #)
1
2
NA
3
4
10.4”
11.3”
5
6
12.1”
13.8”
7
8
NA
NA
8.4”
Format
0 = VGA
1 = SVGA
2 = XGA
3 = SXGA
640.480
800.600
1024.768
1280.1024
Examples:
3261 = 14″ (13.8″) 1024.768 XGA display
3153 = 12″ (12.1″) 800.600 SVGA display
46
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
Limited Warranty
Lucas Control Systems warrants this product against defects in materials and workmanship for a
period of one year (12 months) from the date of original shipment from the factory with the
following exceptions:
•
•
Active Matrix LCD Display. The original equipment manufacturers warranty will apply.
Electroluminescent Display. The original equipment manufacturers warranty will apply.
During this warranty period, Lucas Control Systems will, at no cost to the buyer, promptly repair or
replace defective equipment returned to the factory or other authorized warranty repair center,
transportation charges pre-paid by the buyer, and will return such equipment, transportation charges
pre-paid. Lucas Control Systems’ sole obligation shall be at its option, to repair or replace any goods
which have been determined to be defective by Lucas Control Systems.
Equipment returned to the factory shall be accompanied by the following information:
•
•
•
•
Returned Material Authorization (RMA) number, obtained from Lucas Control Systems.
Reason for return, with a comprehensive description of the malfunction.
The name and telephone number of the person to contact in the event of questions or problems.
Shipping instructions.
This warranty shall not apply to damage resulting from the improper handling, accident, negligence,
loss or damage in transit, or abuse (such as applying the wrong voltage). This warranty shall be
voided should the buyer attempt repairs or alterations without prior written permission from Lucas
Control Systems.
Lucas Control Systems makes no other warranty, either expressed or implied, and disclaims any
warranty or merchantability or fitness for a particular purpose.
Any action by Buyer for any alleged breach of this warranty shall be brought to the attention of
Lucas Control Systems by the Buyer within the warranty period.
Repairs and/or replacement under terms of this warranty shall not extend the warranty life of the
original equipment supplied.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
LIMITATIONS OF LIABILITY
THE BUYER AND LUCAS CONTROL SYSTEMS AGREE THAT THE SOLE AND EXCLUSIVE
REMEDIES FOR BREACH OF ANY WARRANTY SHALL BE REPAIR OR REPLACEMENT OF
DEFECTIVE PARTS ACCORDING TO THE TERMS DESCRIBED ABOVE. LUCAS CONTROL
SYSTEMS SHALL NOT BE LIABLE FOR CONTINGENT OR CONSEQUENTIAL DAMAGES
TO PERSONS OR PROPERTY, AND LUCAS CONTROL SYSTEMS’ SOLE LIABILITY IS AS
SET FORTH ABOVE. THIS STATEMENT OF WARRANTY IS A COMPLETE AND
EXCLUSIVE STATEMENT OF ALL WARRANTY AND LIABILITY REPRESENTATIONS OF
LUCAS CONTROL SYSTEMS. IT MAY NOT BE VARIED, SUPPLEMENTED, QUALIFIED OR
INTERPRETED BY ANY PRIOR DEALINGS BETWEEN THE PARTIES OR BY ANY USAGE
OF THE TRADE OR UPON THE FACE OR REVERSE OF ANY FORM TO WHICH THIS IS
ATTACHED OR PART OF, NOR MAY IT BE MODIFIED BY ANY AGENT, EMPLOYEE, OR
REPRESENTATIVE OF LUCAS CONTROL SYSTEMS.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
Index
1
10 BASE-T Connector, 18
A
Applying Power, 8
B
BIOS, 23, 24
D
Diagnostics, 2
DOS, 2
E
Ethernet, 17
F
Fuse, 31
G
Green PC, 2
I
Input Power, 25, 26, 27, 29
49
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
L
LAN, 17
LCD, 47
M
Mounting, 8, 35
Mouse, 2, 17
N
Novell, 2
O
OS/2, 2
Output Power, 25, 30
P
Parallel Port, 16
Power, 2
Power Requirements, 9
S
SBC, 15
SIMM, 27, 35
Specifications, 5
T
Touch, 26, 35
Troubleshooting, 23, 24, 25, 26, 27
U
UNIX, 2
50
Download from Www.Somanuals.com. All Manuals Search And Download.
EM-C061 Computer User Manual
W
Windows, 2
51
Download from Www.Somanuals.com. All Manuals Search And Download.
|