LWX-1
WEATHER
Satellite Weather Radio Module
Installation Instructions
988-0158-13A
Download from Www.Somanuals.com. All Manuals Search And Download.
This document covers the installation and status/diagnostic indicators available for
the Lowrance LWX-1. It also details how to activate a SIRIUS subscription.
LWX-1 package include:
Main Components:
1. Antenna Receiver (AR) pre-configured for a mast mount
•
AR Interconnect Cable (attached to AR) connects to IM
2. Interface Module (IM)
•
•
IM Power Cable (attached to IM) connects to Vessel power
IM Network Cable (attached to IM) connects to ChartPlotter
Mounting Components:
1. AR Gasket (1)
2. AR Mounting Screws (4)
3. IM Mounting Screws (2)
4. AR Screw Caps (5; one extra)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
LWX-1 Installation Options
The LWX-1 can be mounted in three basic configurations:
1. AR Mast Mount (factory-installed option)
2. AR Flush Mount with cable routed through the mounting surface
(e.g. deck)
3. AR Flush Mount with cable routed on top of the mounting surface
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1. AR Mast Mount Installation
The LWX-1 AR is shipped in the retail box factory-configured for a mast mount.
To use AR Mast Mount Installation:
1. Loosen the four AR Bolts & Nuts (a couple of counter-clockwise
turns on each).
2. The AR Mast Boot will loosen, allowing the AR Mast Mount to turn.
3. Insert the AR Interconnect Cable into the Antenna Mount and route
it carefully to the Interface Module (IM). Planning the cable route in
advance will avoid multiple cable pulls that could increase the likeli-
hood of damaging the connector.
4. Align the AR in the general position desired and screw the AR Mast
Mount onto the Antenna Mount (hand-tighten as much as possible
– DO NOT OVER-TIGHTEN). Note that the AR is a friction fit de-
signed to allow for the occasional hand alignment.
5. With the AR Mast Mount installed, align the AR in position desired
and re-tighten the four AR Bolt & Nuts.
6. Insert AR Screw Caps into AR Bolt recesses on the AR Cover.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. AR Flush Mount Installation (through deck)
AR Flush Mount with cable routed through the deck.
To use AR Flush Mount through-deck installation:
1. Remove the four AR Bolts & Nuts (the AR Cover and AR Base are
factory fitted – DO NOT ATTEMPT TO SEPARATE THEM)
2. Use the AR Gasket as a template to mark where the AR Mounting
Screws and AR Interconnect Cable holes are to be pre-drilled
3. Drill the 1/32 inch diameter starter holes for theAR Mounting Screws
and the 1/2 inch diameter hole to route the AR Interconnect Cable
through the deck. Make sure the gasket is sealed tightly against the
deck
4. Insert AR Interconnect Cable through the deck and pull it through
5. Using the four AR Mounting Screws provided, mount the AR to the
deck
6. Insert AR Screw Caps into AR Bolt recesses on the AR Cover
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. AR Flush Mount Installation (above deck)
In this AR Flush Mount installation, the cable is routed out the back of the LWX-1.
This installation is the same as AR Flush Mount through-deck Installation, except
the AR Interconnect Cable is routed under the LWX-1 and out the back above the
deck instead of through the deck.
To use AR Flush Mount above-deck installation:
1. With a pair of needle-nose pliers, break away and remove the AR
Channel Stop
2. Insert the AR
Interconnect Cable
into cable channel on
bottom of LWX-1
3. Ensure that the rubber
boot on the AR Inter-
connect Cable is firmly
in the AR Rubber Boot
Inset so that it is flush
with the bottom of the
AR Base.
4. Gently form the AR Interconnect Cable from the exit of the rubber
boot up and over the rear cable exit of the AR Base
5. Replace the AR Gasket on the AR Base, over the AR Interconnect
Cable, and then install the AR as described in “2. AR Flush Mount
through deck installation.”
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IM Installation
With all of the AR installation options, it is recommended that the IM is mounted/
installed below deck.
To install the IM:
1. Open the IM enclosure by unscrewing the two IM Enclosure Screws
on the front panel
2. Insert the male RJ45
connector on the end
of the AR Interconnect
Cable into the female
RJ45 connector in the
middle of the inside of
the IM enclosure. The
RJ45 connector will
click into place when it
is connected correctly
3. Route the AR Intercon-
nect Cable through the
exit slot of the IM en-
closure (between the
other two cables) and close the IM
4. Re-insert and tighten IM Enclosure Screws (from Step 1) on the IM
cover
5. Mount the IM with the IM Mounting Screws provided, on a vertical
surface, with the cables exiting downwards
6. Connect the IM Power Cable to the vessel’s power (8 to 16 VDC
source)
7. Connect the IM Network Cable to the Chartplotter
6
Download from Www.Somanuals.com. All Manuals Search And Download.
LWX-1 Status Indicators
The LWX-1 status indicators are the two LEDs on the Interface Module. The IM in-
dicators are to be used to obtain connectivity with the end-user device, where more
detailed problem diagnosis is available.
Power LED indicates LWX-1 Power:
1. LED OFF
— No power to the Interface Module
2. LED ON (solid green)
— Power to Interface Module
Status LED indicates LWX-1 Status:
1. LED OFF
— Interface Module is not powered on
— Antenna Receiver is disconnected
— Antenna Receiver has malfunctioned and is inaccessible
2. LED ON (solid green)
— Antenna Receiver is functioning correctly and providing SIRIUS Data
and SIRIUS Audio (at least preview-level Audio and Data)
3. LED ON (blinks ON/OFF three times during the power-up cycle)
— Antenna Receiver is functioning correctly; however, IM Network
Cable is not connected to end-user device or end-user device is not
operational.
4. LED ON (blinks ON/OFF three times during power-up cycle) then
turns OFF
— Antenna Receiver is not functioning correctly and IM Network Cable is
not connected to end-user device
7
Download from Www.Somanuals.com. All Manuals Search And Download.
If LED blinks ON/OFF three times during the power-up cycle and then turns OFF,
an Ethernet loop back connector should be connected to the IM Network Cable and
the LWX-1 should be power cycled. If the blinking during power-up does not recur,
then the IM Network Cable is good, and the end-user device should be checked.
When IM Network Cable is properly connected to the host device, the end-user can
request a full LWX-1 Diagnostics Report to perform any further required diagnosis.
The following section describes the information provided in this diagnostic report.
The SIRIUS satellite service activation process will require the SIRIUS ID for the
SIRIUS Radio Module is visible to the user. This will allow the SIRIUS Listener
Care call center to activate the user’s subscription for the LWX-1. Signal Strength
will also be important information for the user to verify that SIRIUS radio signal is
available as this is required for successful activation.
LWX-1 SIRIUS Activation
You must have a SIRIUS subscription to use the LWX-1 module. Individual weather
and audio subscriptions are available. You can also purchase a subscription that
includes both weather and audio.
Before calling SIRIUS to activate a subscription for your LWX-1 make sure the
following conditions are met:
•
The LWX-1 and your display unit are turned on and connnected via
ethernet cable
•
SIRIUS status info — antenna status and signal strength — is shown
on your display unit screen (refer to your unit’s operation manual to
access the SIRIUS status screen)
•
•
SIRIUS status screen shows signal strength of at least 1/3 with 2/3 or
greater preferred
Have the ESN — electronic serial number — for the LWX-1 readily
available (ESN, a 12-digit number, can be found on the LWX-1 carton,
LWX-1 antenna or via the SIRIUS status screen)
•
Credit card/billing information is available
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Signal strength, ESN and
Your ESN is also shown on the
antenna status are shown on label attached to the LWX-1 carton
the SIRIUS status screen
To activate a SIRIUS subscription:
1. After the LWX-1 module is installed, locate the label on the front flap
of the LWX-1 carton
2. Record your ESN number (SIRIUS ID) and contact SIRIUS at 1-800-
869-5480. SIRIUS Marine Weather service can only be activated by
phone.
NOTE: It may take several minutes for the activation signal
to be received after subscription is activated.
3. Access SIRIUS status screen to make sure subscription (Weather
Status, Audio Status, or both) is listed as Active. If your account is
inactive, contact information for SIRIUS will be displayed.
4. Check the SIRIUS signal level (1 is weak; 3 is excellent) and make
sure your antenna is listed as “Connected.”
9
Download from Www.Somanuals.com. All Manuals Search And Download.
LWX-1 Diagnostic Report
The following information is shown in the Diagnostic Report retrievable by the
Chartplotter. To view the Diagnostic report, access the SIRIUS Status screen and
press MENU.
LWX-1 System Information
Name
LWX-1 Software Software version LWX-1 is
Version running
LWX-1 Revision Revision level of the LWX-1
Description
Example
LWX200807280148
LWX-NV-A
Level
hardware
LWX-1
Serial number assigned to this 11090371
Electronic Serial LWX-1 during production
Number
Data Activity
Indicates data is being
received
1
Rx Count
Number of data messages
received by the LWX-1
27871
Service Level
Activation level of the sub- 1
scribed data service is shown.
Values are assigned as follows:
0 – deactivated or unknown
1 – Inland Service Level
2 – Offshore Service Level
Position
The location of the receiver is 37.352962-
shown. When the location is not 73.536163
known, the value will be report-
ed as “Unknown”
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SIRIUS Module Information
Description
Name
Example
Radio Activation
Status - Data
Indicates the activation
status of the SIRIUS
Radio Module. The first
value indicating an active
subscription.
1 of -1
This indicates a fully
activated receiver.
Parameter 1 — indicates
is set to ‘1’ when there are
subscribed channels.
Parameter 2 — provides
a bit mask for the
individualized, enabled and
activated status indicators
(counting up from bit 0).
This is a hexadecimal value.
Parameter 3 — indicates
minutes left on a time limited
activation. ‘-1’ implies no
timeout.
Radio Activation
Status – Audio
Same as above
Same as above
Radio Active
Indicates SIRIUS Radio
Module is active
1
1
Radio Antenna
Status
Indicates the internal
antenna is connected to the
SIRIUS Radio Module.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio Signal
Strength
Indicates the signal strength
received by the SIRIUS
Radio Module. The value
is in the range of 0-3 with 3
being maximum.
2
Values are defined as
follows:
0 = no signal
1 = weak signal
2 = good signal
3 = excellent signal
Radio Channel –
Data
Indicates the tuned data
channel for the SIRIUS
Radio Module
199
Radio SIRIUS ID
Indicates the SIRIUS ID for
data of the SIRIUS Radio
Module
005102294176
14
Radio Channel -
Audio
Indicates the tuned audio
channel for the SIRIUS
Radio Module
12
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVICO
LIMITED TWO-YEAR LOWRANCE WARRANTY
“We,” “our,” or “us” refers to NAVICO, the manufacturer of this Lowrance product. “You” or “your” refers to
the first person who purchases this product as a consumer item for personal, family or household use.
We warranty this product against defects or malfunctions in materials and workmanship, and against failure to
conform to this product’s written specifications, all for two (2) years from the date of original purchase by you.
WE MAKE NO OTHER EXPRESS WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER
CONCERNING THIS PRODUCT.
Your remedies under this warranty will be available so long as you can show in a reasonable manner that any
defect or malfunction in materials or workmanship, or any non-conformity with the product’s written specifica-
tions, occurred within two years from the date of your original purchase, which must be substantiated by a dated
sales receipt or sales slip.
Any such defect, malfunction, or non-conformity which occurs within two years from the original purchase date
will either be repaired without charge or be replaced with a new product identical or reasonably equivalent to
this product, at our option, within a reasonable time after our receipt of the product. If such defect, malfunc-
tion, or non-conformity remains after a reasonable number of attempts to repair by us, you may elect to obtain
without charge a replacement of the product or a refund for the product.
THIS REPAIR, OR REPLACEMENT OR REFUND (AS JUST DESCRIBED) IS THE EXCLUSIVE REME-
DYAVAILABLE TO YOU AGAINST US FOR ANY DEFECT, MALFUNCTION, OR NON-CONFORMITY
CONCERNING THE PRODUCT OR FOR ANY LOSS OR DAMAGE RESULTING FROM ANY OTHER
CAUSE WHATSOEVER. WE WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANYONE
FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR OTHER INDIRECT DAMAGE OF ANY
KIND.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you. This warranty does NOT apply in the following circumstances:
(1) when the product has been serviced or repaired by anyone other than us; (2) when the product has been con-
nected, installed, combined, altered, adjusted, or handled in a manner other than according to the instructions
furnished with the product; (3) when any serial number has been effaced, altered, or removed; or (4) when any
defect, problem, loss, or damage has resulted from any accident, misuse, negligence, or carelessness, or from
any failure to provide reasonable and necessary maintenance in accordance with the instructions of the owner’s
manual for the product.
We reserve the right to make changes or improvements in our products from time to time without incurring the
obligation to install such improvements or changes on equipment or items previously manufactured.
This warranty gives you specific legal rights and you may also have other rights which may vary from state to
state. You must retain the sales slip or sales receipt proving the date of your original purchase in case warranty
service is ever required.
NAVICO
12000 E. SKELLY DRIVE, TULSA, OK 74128
WWW. LOWRANCE.COM
13
Download from Www.Somanuals.com. All Manuals Search And Download.
988-0158-13A
Pub. 012809
© Copyright 2009
All Rights Reserved
Navico
Download from Www.Somanuals.com. All Manuals Search And Download.
|