Elite-5HDI Combo
Operation manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that of the receiver
Consult the dealer or an experienced technician for help
WARNING: When a GPS unit is used in a vehicle, the vehicle operator is solely responsible for operating
the vehicle in a safe manner. Vehicle operators must maintain full surveillance of all pertinent driving or
boating conditions at all times. An accident or collision resulting in damage to property, personal injury or
death could occur if the operator of a GPS-equipped vehicle fails to pay full attention to travel conditions
and vehicle operation while the vehicle is in motion.
Download from Www.Somanuals.com1. All Manuals Search And Download.
Table of contents
Fishing Modes.........................................9
Cursor....................................................10
Goto cursor............................................10
Advanced Mode .................................... 11
Standby mode ....................................... 11
Restore defaults .................................... 11
Pages.............................................. 12
Steer Page.............................................12
Sonar Page............................................12
DownScan page ...................................13
Chart Page ............................................13
Combo pages........................................14
Overlay Data..........................................15
Introduction...................................... 4
Unit Controls............................................4
Inserting microSD cards ..........................5
Basic Operation............................... 6
Setup wizard............................................6
Pages ......................................................6
Selecting Pages.......................................6
Page menus ............................................6
Accessing the Settings menu..................7
Accessing menu items.............................8
Working with menus ................................8
Dialogs.....................................................8
Entering text ............................................9
Table of Contents | Elite-5 HDI
2
Download from Www.Somanuals.com. All Manuals Search And Download.
DownScan Operation.................... 17
Trackback .............................................17
Ping Speed............................................19
DownScan options.................................20
Sonar Operation ............................ 22
Trackback..............................................22
Sensitivity ..............................................24
Colorline ................................................24
Range....................................................24
Frequency .............................................25
Ping Speed............................................25
Fish ID ..................................................27
Sonar Settings.......................................28
Installation .............................................30
Chart Operation ............................. 31
Waypoints, Routes, Trails......................32
Routes Screen.......................................34
Trails Screen .........................................38
Orientation.............................................40
Overlay Data..........................................40
Settings..................................................40
Chart Settings........................................41
Navigation Settings ...................................42
Settings .......................................... 44
Settings menu........................................44
System...................................................44
Saving Screenshots...............................46
Alarms ..................................................46
Specifications ................................ 48
Index............................................... 49
Table of Contents | Elite-5 HDI
3
Download from Www.Somanuals.com. All Manuals Search And Download.
introduction
Getting Started
unit Controls
To turn on/off the unit, press and hold
the LiGht/Power key for three
seconds.
Turn unit
on/off
LiGht/Power: controls backlight level
and turns unit on/off
Press the zoom in and zoom out
keys at the same time to set a Man
Overboard waypoint. Your system will
KeYPAD: controls cursor & selects items
on menus
Man
Overboard automatically create an active route
PAGeS: allows you to select a page to view
back to the MOB waypoint. You must
waypoint
cancel navigation to terminate the
function.
menu: opens settings, context and page
menus
Adjusting
the
backlight
This unit has 11 backlight levels. Press
the LiGht/Power key to switch
backlight levels.
enter: finalizes menu selections; save
waypoint at cursor position
moB: press and hold both Zoom keys to
create a Man Overboard waypoint
Select Audio from the System menu.
Select Mute and press enter.
Muting
Audio
zoom KeYS: (+) used to zoom in; (-)
used to zoom out
Select GPS from the System settings
microSD slot: insert a blank microSD card to save
screen captures, sonar logs, waypoints, routes and
trails; or insert a microSD mapping card to use
mapping data
Selecting a menu. Press menu
select GPS
,
GPS source source and choose the desired
source.
Introduction | Elite-5 HDI
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventional sonar and DownScan
inserting microSD cards
This unit supports two types of sonar: Conventional
and DownScan.
Carefully slide the microSD card into the slot until
it clicks into place.
To remove, carefully push in the card until it clicks
out of place.
Conventional
DownScan
Refer to the “Sonar Operation” section for
information about conventional sonar features and
settings.
DownScan features and settings are covered in the
“DownScan Operation”section.
Introduction | Elite-5 HDI
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Setup wizard
The Setup wizard will appear when the unit is
turned on for the first time. To choose your own
settings, do not run the setup wizard. To restart the
Setup wizard, restore defaults.
Selecting Pages
To select a page, press the keypad in the direction
of the desired page and press EntEr.
Page menus
The Steer, DownScan, Sonar and Chart pages have
menus that can only be accessed when those
pages are displayed.
Pages
This unit has eight pages: Steer, DownScan, Sonar,
Chart, Chart/Sonar, Chart/DownScan, Sonar/
DownScan and Chart/Sonar/DownScan.
Steer menu
Steer page
Pages dialog
Basic Operation | Elite-5 HDI
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Combo pages
DownScan page
Three-panel page
Two-panel page
DownScan menu
Press the PagES key twice to switch active
panels. The page menu for the active page will be
displayed when the MEnu key is pressed.
accessing the Settings menu
Sonar page
Sonar menu
Chart menu
Chart page
Basic Operation | Elite-5 HDI
7
Download from Www.Somanuals.com. All Manuals Search And Download.
On/Off features
accessing menu items
Select an on/off menu item and
press EntEr to turn it on/off.
The keypad and EntEr key are used to select
menu items and open submenus. Use the keypad
to highlight the desired item and press EntEr.
Dropdown menus
Access the dropdown
menu and press the
keypad up/down to select
the desired item and press
EntEr.
Working with menus
nOtE: Press the MEnu key to exit
menus.
There are several menu types used to make
adjustments to options and settings, including
scrollbars, on/off features and dropdown menus.
Dialogs
Dialogs are used for user input or
for presenting information to the
user. Depending on the type of
entry, different methods are used
to confirm, cancel or close the
dialog.
Scrollbars
Select the scrollbar and press the
keypad left (decrease) or right
(increase).
Basic Operation | Elite-5 HDI
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering text
Fishing Modes
Some functions, like naming a waypoint, route or
trail, will require you to input text.
(Conventional sonar only)
Fishing modes enhance the performance of your
unit by providing preset packages of sonar settings
geared to specific fishing conditions.
To input text:
1. Use the keypad to select the desired
character and press EntEr.
2. Repeat Step 1 for each character.
3. When entry is completed, highlight OK
and press EntEr.
Switches letters
to uppercase/
lowercase
Switches keyboard
between ALPHA and
QWERTY layout
Basic Operation | Elite-5 HDI
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Cursor
Fishing Mode Options
The keypad moves the cursor around the display,
allowing you to scroll the map, select map items
and review sonar history.
General Use
1000ft or less
Coastal
Shallow
Water
Shallow weedy
bottoms
60ft or less
Press MEnu and select Return to vessel or Exit
cursor mode to clear the cursor.
Fresh Water
Deep Water
400ft or less
1000ft or more
400ft or less
Inland/Near coastal
Offshore
Slow
Trolling
Inland/Coastal
goto cursor
Fast
Trolling
400ft or less
400ft or less
Inland/Coastal
Inland/Coastal
Used to navigate to the cursor.
1. Move the cursor to a desired location
Clear Water
and press MEnu.
Brackish
Water
400ft or less
400ft or less
Fresh-Saltwater mix
2. Select Goto cursor and press EntEr.
Ice
Ice fishing
Basic Operation | Elite-5 HDI
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
advanced Mode
Standby mode
Enables advanced features and settings.
Lowers power consumption by turning off sonar
and the display.
The following features are enabled when Advanced
mode is turned on:
1. Press the PWr/Light
key to access the Back-
light dialog.
•
Navigation (Enables arrival radius, off-
course distance and Bearings setting)
2. Select Standby and
•
Alarms (Enables arrival, off course and
anchor alarm options)
press EntEr.
3. Press any key to resume normal
operation.
•
•
NMEA 0183 configuration options
Units (Enables distance, speed, depth,
temperature and bearings configuration
options)
nOtE: Leaving your unit in Standby
mode when your boat is not in use will run
down your battery.
restore defaults
Sets unit options and settings
to default values.
Basic Operation | Elite-5 HDI
Download from Www.Somanuals.co1m1. All Manuals Search And Download.
Pages
Surface Clutter
Course over ground
Fish arches
Compass
Direction to destination
Current vessel location
Colorline
Navigation
information
Range
Scale
Steer Page
Sonar Page
The Steer page has a compass that shows your Displays the water column moving from right to
current track, the direction to your destination, and left on your unit’s screen.
a digital data navigation panel.
Pages | Elite-5 HDI
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Waypoint
Surface clutter
Baitfish
Current vessel location
Cursor
Structure
Current location and distance/
bearing from vessel to cursor
Zoom
Range
Range scale
DownScan page
The DownScan page shows the water column
moving from right to left. You can overlay
DownScan sonar on the conventional sonar page
by selecting DownScan Overlay on the Sonar
settings menu.
Chart Page
Consists of map that moves in real-time as you
move. By default, the map is shown from a birds-
eye view with North at the top of the screen.
Pages | Elite-5 HDI
Download from Www.Somanuals.co1m3. All Manuals Search And Download.
Combo pages
This unit has four pre-configured combo pages.
Customizing combo pages
You can adjust the panel size of combo
pages and control how the
pages will be arranged on
the screen: vertically (side) or
horizontally (over).
Chart/Sonar
Chart/DownScan
Sonar/DownScan
Chart/Sonar/DownScan
NOTE: Press the PagES key twice to
switch active panels.
Pages | Elite-5 HDI
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Overlay Data
Used to select data shown on the Sonar, DownScan
and Chart pages.
To add overlay data:
1. From the Sonar, Chart or DownScan
page, press MENu.
2. Select Overlay data and press ENTEr.
3. Select Configure and press ENTEr.
Overlay data
Show
4. Press Menu and select Add. Press
ENTEr.
Enables/disables the display of overlay data,
allowing you to remove overlay data from the
screen without deleting the current overlay data
configuration.
5. Select a data category and press
ENTEr.
6. Select the desired data and press
ENTEr.
7. Repeat Steps 5 and 6 to add more data.
8. Press MENu and select Return to
Configure
Overlays. Press ENTEr.
Allows you to select/customize overlay data.
9. Press MENu, select Done Configuring
and press ENTEr.
Download from Www.Somanuals.co1m5. All Manuals Search And Download.
Pages | Elite-5 HDI
Customizing Overlay Data
You can add/remove data
and adjust the size and
position of overlay data on
the screen.
Select the desired overlay
data from the “Configure
Item Locations and Sizes
dialog” and press MENu. The configuration menu
will appear.
Pages | Elite-5 HDI
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Move the sonar history bar all the way to the right
to resume normal sonar scrolling, or press Menu
and select Exit cursor mode.
DownScan Operation
This unit supports two types of sonar: Conventional
and DownScan.
DownScan menu
Press Menu from the DownScan page to view the
DownScan menu.
The features described in this section are for
DownScan sonar. Refer to the “Sonar operation”
section for information on conventional sonar
features.
Trackback
You can review your sonar history by pressing the
keypad to the left until the screen starts to move
in reverse and the sonar history bar appears at the
bottom of the screen.
DownScan history bar
Stops sonar
transmission;
pauses sonar
scroll
DownScan Operation | Elite-5 HDI
Download from Www.Somanuals.co1m7. All Manuals Search And Download.
New Waypoint
Contrast
Places a waypoint at your current position or at the
cursor position. From the new waypoint menu, you
can input a waypoint name, select an icon and
input a desired latitude/longitude.
Adjusts the brightness ratio between light and dark
areas on the screen, making it easier to distinguish
suspended objects from the background.
Contrast set
to 40%
Contrast set
to 60%
Contrast set
to 80%
DownScan units do not have a Sensitivity setting
like traditional sonar units. Contrast functions as
the sensitivity setting for DownScan units.
New waypoint menu
Adjust
Access the Adjust menu to make
adjustments to the contrast level.
Auto Contrast
Automatically adjusts contrast settings to a level
that works best with current water conditions.
DownScan Operation | Elite-5 HDI
Download from Www.Somanuals.co1m8. All Manuals Search And Download.
view a section of the water column that does not
include the water surface.
NOTE:You can make limited adjustments
to the contrast level with Auto Contrast
turned on. You will have to turn it off to
have access to all contrast levels.
Upper and lower limits must be at least 5 ft (2m)
apart.
nOTe: When using a custom range,
you may not receive any digital depth
readings, or you may receive incorrect
depth information.
Range
Range settings display the section of the
water column from the water surface to
the selected depth range.
Frequency
Custom Range — Upper and Lower Limits
Controls the transducer frequency
used by the unit. 800 kHz offers the
best resolution, while 455 kHz has greater depth
coverage.
Used to select the upper limit and lower limit of
a section of the water column. That allows you to
Ping Speed
Controls the rate the transducer uses to send sonar
waves into the water. Ping speed adjustments can
help reduce interference from other transducers.
DownScan Operation | Elite-5 HDI
Download from Www.Somanuals.co1m9. All Manuals Search And Download.
DownScan options
Surface Clarity
set to Low
Surface Clarity
set to High
DownScan options
Split Zoom
Changes the display to a split zoom view. You can
select a 2X or 4X zoom level. Press the +/- keys to
zoom in/ zoom out.
Noise Rejection
Uses advanced signal processing to monitor the ef-
fects noise (boat pumps, water conditions, engine
ignition systems, etc.) has on your display, and then
filters out undesired signals.
Color
Allows you to select a color
palette best suited to your
fishing conditions.
Surface Clarity
The white background palette works well for
suspended targets. Purple is useful for viewing
structure detail and determining bottom hardness.
Sepia is best for looking at bottom detail.
Surface Clarity reduces surface clutter by
decreasing the sensitivity of the receiver near the
surface.
DownScan Operation | Elite-5 HDI
Download from Www.Somanuals.co2m0. All Manuals Search And Download.
Stop Sonar
Overlay Data
Stops sonar transmission and pauses the sonar Allows you to select data to
chart, allowing you to get a better look at be displayed on top of the
suspended targets and structure.
DownScan page.
Overlay data setup is covered
in the “Pages”section.
Overlay data
nOTe: Sonar history (Trackback) will
not be recorded when sonar is stopped.
Settings
Logging Sonar
Accesses the Settings menu. Refer to ”Sonar
Settings”on page 27.
You can record sonar data and save the file on a
microSD card inserted into the unit’s card reader.
View previously
saved sonar logs
DownScan Operation | Elite-5 HDI
Download from Www.Somanuals.co2m1. All Manuals Search And Download.
Blue tory bar
Sonar Operation
This unit supports two types of sonar: Conventional
and DownScan.
Trackback
You can review your recent sonar history by mov-
ing the cursor to the left until the screen starts to
move in reverse.
Move the sonar history bar all the way to the right
to resume normal sonar scrolling, or press Menu
and select Exit cursor mode.
The features described in this section are for
conventional sonar.
Sonar Menu
Refer to the “DownScan operation” section for
information on DownScan features.
Press Menu from any sonar
page to access the Sonar
menu.
Sonar Operation | Elite-5 HDI
Download from Www.Somanuals.co2m2. All Manuals Search And Download.
Shown with DownScan
overlay enabled
New Waypoint
Places a waypoint at your current position or at the
cursor position. From the new waypoint menu, you
can input a waypoint name, select an icon and
input a desired latitude/longitude.
(active only with
DownScan overlay
enabled)
Used to record
sonar logs
Sonar Menu
(Advanced Mode)
New waypoint menu
Adjust
You can make adjustments to Sensitivity
and Colorline from the Adjust menu.
Contrast and Overlay options will only
be active on the Adjust menu with
DownScan Overlay enabled.
Sonar Operation | Elite-5 HDI
Download from Www.Somanuals.co2m3. All Manuals Search And Download.
Sensitivity
NOTE: You can make changes (+/-40%)
to sensitivity with Auto Sensitivity turned
on. You will have to turn it off to make
significant adjustments.
Controls the level of detail shown on the display.
Too much detail will clutter the screen. If Sensitivity
is set too low, desired echoes may not be displayed.
Range
Colorline
Selects the deepest range shown on
the display. Range settings display the
section of the water column from the
water surface to the selected depth
range.
Separates strong sonar echoes from weak sonar
echoes. That makes it easier for you to distinguish
fish or structure from the bottom. A hard return
will be shown as a wide, bright yellow area,
whereas a soft return will be a narrow reddish-
blue area.
If you select too shallow a depth range, the unit will
not be able to lock onto the bottom.
Auto Sensitivity
Custom Range — Upper and Lower Limits
Keeps sensitivity at a level that works well under
most conditions, reducing the need for adjust- Used to select the upper limit and lower limit of
ments. Auto Sensitivity is turned on by default.
a section of the water column. That allows you to
view a section of the water column that does not
include the water surface. Upper and lower limits
must be at least 5 ft (2m) apart.
Sonar Operation | Elite-5 HDI
Download from Www.Somanuals.co2m4. All Manuals Search And Download.
Ping Speed
Controls the rate the transducer uses to send sonar
waves into the water. Ping speed adjustments can
help reduce interference from other transducers.
When using fishing modes, ping speed settings are
optimized for the selected fishing conditions, so in
most cases, adjustments are not necessary.
Custom range
menu
nOTe: When using a custom range, you
may not receive any digital depth read-
ings, or you may receive incorrect depth
information.
Frequency
Controls the transducer frequency used by the
unit. This unit supports three conventional sonar
frequencies: 50kHz, 83kHz and 200kHz.
200 kHz has the highest sensitivity and best target
discrimination in shallow water. 83 kHz offers a
wider cone angle for more water coverage. 50 kHz
provides the best depth penetration.
Sonar Operation | Elite-5 HDI
Download from Www.Somanuals.co2m5. All Manuals Search And Download.
Surface Clarity
Sonar Options
Surface Clarity reduces sur-
face clutter by decreasing the
sensitivity of the receiver near
the surface.
Surface Clutter
Split Zoom and Split Flasher
Switches the sonar display from full screen sonar to
a split screen view.
Noise Rejection
Uses advanced signal processing to monitor the ef-
fects noise (boat pumps, water conditions, engine
ignition systems, etc.) has on your display, and then
filters out undesired signals.
Split Zoom
Split Flasher
Color
Allows you to change the look of the display using
palettes with varying degrees of color/brightness.
Sonar Operation | Elite-5 HDI
Download from Www.Somanuals.co2m6. All Manuals Search And Download.
Amplitude Scope
Amplitude
scope
Displays the amplitude of the
most recent echo.
DownScan options menu
Fish ID
Displays fish echoes as fish symbols instead of fish
arches.
Fish ID is not the most accurate
method of fish detection since
structure and suspended debris
may be shown as a fish symbol on
the display.
nOTe: The DownScan options menu
will only be available when DownScan
overlay is enabled.
Stop Sonar
Pauses the unit’s sonar, allowing you to get a closer
look at suspended targets. Stop Sonar also can be
used to prevent/stop interference between two
sonar units running on the boat at the same time.
DownScan options
You can make adjustments to DownScan overlay
settings from the sonar page. DownScan options
are covered in more detail in the “DownScan
Operation”section.
nOTe: Sonar history will not be
recorded when sonar is stopped.
Sonar Operation | Elite-5 HDI
Download from Www.Somanuals.co2m7. All Manuals Search And Download.
Logging Sonar
Sonar Settings
You can record sonar data and save the file on a
microSD card inserted into the unit’s card reader.
View previously
saved sonar logs
Conventional settings/DownScan Settings
You can adjust settings for both Conventional so-
nar and DownScan sonar modes from the Sonar
Settings menu.
Overlay Data
Allows you to select data to
be displayed on top of the
Sonar page. Overlay data
setup is covered in the“Pages”
Only adjustments made to conventional sonar
settings will be visible on the sonar page.
section.
Overlay data
Sonar Operation | Elite-5 HDI
Download from Www.Somanuals.co2m8. All Manuals Search And Download.
Restricts
When the unit is in manual mode, you may not
receive any depth readings, or you may receive
incorrect depth information.
unit’s digital
depth search
capability
Turns on/off
DownScan
overlay
Fishing Mode
Enhances the performance of
your unit by providing preset
packages of sonar settings geared
to specific fishing conditions. For
more information about fishing modes, refer to the
“Basic Operation”section.
Sonar Settings Menu
Manual Mode
Reset Fishing Mode
Restricts digital depth capability, so the unit will
only send sonar signals to the selected depth
range. That allows the display to continue smooth
scrolling if the bottom depth is out of transducer
range.
Resets selected fishing mode to default settings.
That is useful when you want to clear settings
adjustments made while using a fishing mode.
WARnInG: Manual mode should only
be used by advanced sonar users.
Sonar Operation | Elite-5 HDI
Download from Www.Somanuals.co2m9. All Manuals Search And Download.
of the keel. If, for example, the keel is 3.5 feet below
the transducer, it will be input as –3.5 feet.
Installation
Water speed calibration
Calibrates a paddlewheel speed sensor with speed
data from a GPS source.
Installation menu
Temperature calibration
Keel Offset
Calibrates data from the transducer temperature
sensor with data from a known temperature source
to ensure the accuracy of temperature information.
All transducers measure water depth from the
transducer to the bottom. As a result, water depth
readings do not account for the distance from the
transducer to the keel or from the transducer to the
water surface. Before setting keel offset, measure
the distance from the transducer to the lowest part
Reset water distance
Resets the Water Distance value to zero.
Transducer Type
Selects the transducer model attached to your unit.
You must select the correct transducer type to get
the best sonar performance from your unit.
Transducer
Keel
Keel Offset (-3.5 feet)
Sonar Operation | Elite-5 HDI
Download from Www.Somanuals.co3m0. All Manuals Search And Download.
Chart Operation
Chart menu
Chart Menu
New Waypoint
Press Menu from the Chart page to open the Chart
menu. Press enter to launch the New waypoint Creates a waypoint at your current location or at the
dialog.
cursor position. When the cursor is on the screen,
waypoints will be saved at the cursor position. If
the cursor is not active, waypoints will be saved at
your current position.
Chart Operation | Elite-5 HDI
31
Download from Www.Somanuals.com. All Manuals Search And Download.
3. To measure from the cursor position to
a new location, press enter and move
the cursor to a new location.
Find
Used to search for chart
categories from the cursor
position or from the vessel
position.
4. To stop measuring, press Menu and
select Stop measuring.
Measure
Waypoints, routes, trails
The cursor can be used to measure the distance
between two items on the chart.
Used to create, edit, navigate and delete way-
points, routes and trails.
Press the keypad left/right to toggle between
waypoints, routes and trails tabs.
To measure distance:
1. Select Measure and press enter.
2. Move the cursor to the desired location.
The distance will be shown in the
measuring dialog.
Waypoints menu
Waypoints Screen
Chart Operation | Elite-5 HDI
32
Download from Www.Somanuals.com. All Manuals Search And Download.
New
Creates a new waypoint at the cursor or vessel
position. You can also
select waypoint name, icon
and
latitude/longitude
from the new waypoint
dialog.
Show
Displays the selected waypoint on the
map.
Waypoints
menu
Goto
Allows you to navigate to a waypoint.
Edit
Delete and Delete All
Allows you to edit the name,
icon and latitude/longitude
of a selected waypoint.
Delete is used to delete a
selected waypoint. Delete
All deletes all waypoints.
Chart Operation | Elite-5 HDI
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Inserts waypoint between
existing route waypoints
Sort
Controls how the waypoints list will be sorted — by
name or by nearest.
Adds waypoint to
end of the route
routes Screen
Used to create, edit, navigate and delete routes.
Use the keypad to highlight the Routes tab to ac-
cess the Routes screen.
Route waypoint
menu
Starts navigation
to the selected
route waypoint
Creating a route
Routes can be created by inserting waypoints from
the waypoints list or by using the cursor to position
points on the chart. You also can add waypoints to
a route by selecting them from the chart screen.
Routes menu
Routes screen
Chart Operation | Elite-5 HDI
34
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Press Menu and select Add to end to
Leg Name field
add another waypoint to the route.
8. Repeat Steps 5-7 until the route is
complete, press Menu, select Stop
Editing and press enter.
9. Select Save and press enter.
Creating a route using points from chart:
1. Repeat Steps 1-4 from the instructions
for Creating a route from waypoint list.
To create a route from waypoint list:
1. Press Menu from the Routes screen.
2. Select New... and press enter.
2. Select Points using chart and press
enter. The chart page will appear.
3. Press the keypad down to highlight the
3. Move the cursor to the desired location.
Leg Name field and press enter.
Press enter to set a point.
4. Press Menu, select Add to End and
4. Repeat Step 3 to add more points.
press enter.
5. Press Menu and select Stop adding.
5. Select Waypoint from list and press
Press enter.
enter.
6. Select Save and press enter.
6. Select the desired waypoint and press
enter.
Chart Operation | Elite-5 HDI
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigating a route
3. Select Forward or Reverse and press
enter.
Routes can be navigated in forward or reverse.
4. Press Menu and select Return to Chart.
1. Highlight the desired route on the Route
Press enter.
screen and press Menu.
To cancel navigation:
2. Select Start and press enter.
1. Press Menu from the chart screen.
2. Select Navigation and press enter.
3. Highlight Cancel and press enter.
4. Select Yes and press enter.
Routes menu
Chart Operation | Elite-5 HDI
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Displayed
Edit and New Route dialogs
Used to edit/create routes, route names and to turn
on/off the route display.
Used to show/hide a route on the display, which
prevents the screen from being cluttered by too
many routes
Displays/hides
route on the map
To edit/create a route, use the
keypad to select the Route
Leg Name field and press
Delete and Delete All
Delete is used to delete
individual routes. Delete
All, removes all routes.
enter.
To access the “Edit” or “New Route” dialog, select
Edit or New on the Routes menu and press enter.
To finalize changes on the “Edit” or “New Route”
dialogs, highlight the Done button and press
enter.
Chart Operation | Elite-5 HDI
37
Download from Www.Somanuals.com. All Manuals Search And Download.
trails Screen
Used to create, edit, navigate and delete trails. Use
the keypad to highlight the Trails tab to access the
Trails screen.
Trails menu
Trails menu
Trails screen
To create a trail:
Creating trails
1. Select New and press enter. The
When creating a trail you can customize the trail
name and color from the New Trail.
New Trail dialog will appear.
2. Select Save and press enter.
Chart Operation | Elite-5 HDI
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit and New Trail dialogs
Navigating a trail
Allows you to edit/create trails, select trails names,
trail color, trail display and the trail being recorded.
You can also convert a trail into a route from the
Edit Trails dialog.
A trail must be saved as a route before it can be
navigated.
To save a trail as a route:
1. Highlight the desired trail on the Trails
screen and press enter. The Edit
Trail menu will appear.
2. Highlight Create Route and press
enter. The Edit Route menu will
appear.
3. Highlight Done and press enter.
Turns on/
off trail
recording
Turns on/
off trail
display
on map
4. For navigation instructions refer to the
“Navigating a route” segment.
Edit Trails dialog
Displayed and Record
Displayed allows you to show/hide trails on the
map display, preventing the screen from being
cluttered with trails.
Chart Operation | Elite-5 HDI
39
Download from Www.Somanuals.com. All Manuals Search And Download.
The Record command allows you to record or
resume recording a desired trail.
Overlay Data
Allows you to select data to be displayed on top of
the Chart page.
Delete and Delete All
Delete is used to remove
individual trails. Delete
All removes all trails.
Overlay data
Orientation
Overlay data setup is covered in the“Pages”section.
Allows you to select North Up or Course Over
Ground (COG) as the map orientation.
Settings
Accesses the “Chart settings”menu.
Chart Operation | Elite-5 HDI
40
Download from Www.Somanuals.com. All Manuals Search And Download.
COG Extension
Chart Settings
A line extending from the front
of the current position icon that
estimates the time and distance
to areas in front of you.
Controls map data used on the chart screen as well
as display settings like grid lines, waypoints, routes
and trails.
Grid Lines
Displays base values for
latitude and longitude, making
it easier to get a general idea of
your location on the latitude/
longitude scale.
Chart Settings menu
Chart Data
Selects map data that will be used on the Chart
display (Lowrance or Navionics regional map). Go
to Navionics.com to see a full selection of available
charts.
Chart Operation | Elite-5 HDI
Download from Www.Somanuals.com. All Manuals Search And Download.
41
Waypoints, Routes and Trail displays
navigation Settings
(Advanced mode only)
From the Chart Settings menu, you can turn on/
off waypoint, route and trail display properties. Controls Arrival Radius and Off Course distance
Turning off display properties allows you to get settings and is used to turn on/off WAAS/MSAS/
a better view of the map, if the screen becomes EGNOS.
cluttered with waypoints, routes and/or trails.
Waypoints, Routes, Trails
Accesses the Waypoints, Routes & Trails screen.
Waypoints, Routes and Trails are covered in the
“Chart operation”section.
Navigation Settings menu
Chart Operation | Elite-5 HDI
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Arrival Radius
Magnetic Variation
Sets the arrival radius threshold for the Arrival Controls whether magnetic variation will be calcu-
alarm. The arrival alarm will sound when your ves- lated using Automatic or Manual settings. Magnet-
sel comes within a selected distance (arrival radius) ic variation is the angle between magnetic north
of the destination waypoint.
and true north. The automatic setting reconciles
the variation for you.
Off Course Distance
WARNING: You should only use the
Manual magnetic variation setting if
you have variation information from a
verified source.
Sets Off Course Distance threshold for the Off
Course alarm. When the selected off course dis-
tance is exceeded, the Off Course alarm will sound
when the alarm is enabled.
Bearings
Controls whether bearing will be calculated using
True North or Magnetic North. Magnetic North
should be used when navigating with a compass
course or heading; otherwise use the default set-
ting, True North.
Chart Operation | Elite-5 HDI
43
Download from Www.Somanuals.com. All Manuals Search And Download.
System
Settings
Adjusts unit settings like language, mute audio
and advanced mode.
Settings menu
Accesses installation and configuration settings for
your unit.
Enables
advanced
features and
settings
Settings
System menu
menu
(Advanced mode
only)
Displays software
information
(Advanced mode only)
Settings | Elite-5 HDI
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Set Language
WAAS/MSAS/EGNOS
Selects the language used on
menus and text boxes.
Turns on/off WAAS, MSAS and EGNOS.
All three systems help increase GPS accuracy for
different parts of the world.
Audio
Time
Adjusts volume and turns on/off unit audio, like
key beeps, alarm sounds, etc.
Used to set local time, and time and date formats
for your unit.
GPS
Monitors the location of satellites
in view and the quality of the
unit’s satellite lock-on. GPS
Source, WAAS/MSAS/EGNOS and
Time features are accessed from
the GPS dialog.
Trip Calculator
Tracks trip time, speed and
distance when you are moving
fasterthantheselectedthreshold.
Advanced Mode
GPS Source
Enables features and settings only available with
unit in Advanced Mode.
Selects the antenna your unit will use for GPS. You
will use the built-in GPS antenna unless you have a
LGC-16W external antenna (p/n: 000-00146-001).
Settings | Elite-5 HDI
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Restore Defaults
Lowrance periodically updates unit software to
add features and improve functionality. To see
the latest available software version go to www.
lowrance.com.
Switches the unit back to default settings.
Browse Files
Allows you to view a list of the files saved to the
microSD card.
Alarms
Enables alarms and selects alarm thresholds.
“Arrival,”“Off Course” and “Anchor” alarms are only
available in Advanced mode.
Saving Screenshots
You can save screenshots to a microSD card by
inserting a microSD card into the card slot and
pressing Power and then Zoom (+).
You must view files on a computer or other microSD
compatible device.
About
Alarms
menu
Displays software information about this unit.
Before attempting a software update, you can
check the version of software your unit is using by
accessing the About screen.
Sounds alarm when
Fish ID symbol
appears on display
Settings | Elite-5 HDI
46
Download from Www.Somanuals.com. All Manuals Search And Download.
NMEA 0183 Output
Alarms
You can select the NMEA 0183 sentences the unit
will use when connected to a VHF radio or other
NMEA 0183 device.
sounds alarm when you are within a selected
distance of your destination (Advanced
Mode only)
Arrival
sounds alarm when course exceeds
a
Off
Course
selected off-course threshold (Advanced
Mode only)
sounds alarm when vessel moves a selected
distance (Advanced Mode only)
Anchor
Shallow
Fish
sounds alarm when vessel enters water
shallower than the selected shallow
threshold
sounds alarm when a fish symbol (Fish ID)
appears on the sonar screen
You can also adjust the Baud rate, but the default
setting works best under most conditions.
Units
Simulator
Allows you to select the unit of measure used by
the unit. Unit options vary depending on whether
the unit is in basic or advanced mode.
Simulates GPS and/or sonar activity. Simulations
can be customized on the Simulator options menu.
Basic Mode
Advanced Mode
Settings | Elite-5 HDI
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Elite-5 HDI
General
Sonar
300ft (91 m) 455/800Khz
1000ft (305 m) 83/200kHz
2500ft (762 m) 50/200kHz
Max depth
5.4”H (136 mm) x 6.9”W (174 mm);
5.9”H (151 mm) with bracket
Case Size
Display
Transducer
Frequency
455/800kHZ and 83/200kHz or
50/200kHz
(5”diagonal) 16-bit color Full
color VGA Solar MAX™ Plus TFT
Waterproof standard IPX7
70mph
Max speed
Backlight
LED (11 levels)
HDI 50/200kHz
HDI 83/200kHz
83/200kHz
Transducer
Communications
NMEA 0183 Output
Declaration of
Conformity
Part 15.103 FCC rules & CE RTTE
directive 1999/5/EC
Transducer cable
20ft (6m)
Power
GPS
Transmit Power
250W RMS; 30,000 PTP
Mapping card slot
GPS Antenna
microSD and microSDHC
Power
Requirement
High accuracy GPS antenna
(internal); optional external GPS
antenna sold separately
12V
Voltage Input
Current drain
Fuse type
10 to 17V
Mapping
compatibility
Fishing Hot Spots
&
Navionics
Typical: 1.1A
(Hotmaps, Premium and Gold)
3-amp Automotive
Up to 3000 waypoints, 100
Waypoints, Routes & routes/100 waypoints per route,
Trails
100 retraceable plot trails/up to
10,000 points per trail
Specifications | Elite-5 HDI
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Chart menu 41
Chart Page 13
COG Extension 41
Color 20, 26
Colorline 24
Contrast 18
Creating a route 34
Creating trails 38
Cursor 10
A
F
K
About 46
Fish alarm 47
Fish ID 27
Fishing Mode 9
Fishing Modes
Reset 29
Keel Offset 30
Adjust menu 23
Advanced Mode 11
Alarms 46
Amplitude Scope 27
Anchor alarm 47
Arrival alarm 47
Arrival Radius 43
Auto Sensitivity 24
L
Language 45
Frequency 19, 25
M
G
Magnetic Variation 43
Man
Overboard
Custom Range 19, 24
Goto cursor 10
Goto waypoint 33
GPS Source 45
GPS Status 45
Grid Lines 41
D
B
waypoint 4
Data Port 45
Depth Range 19
Dialogs 8
DownScan menu 17
Dropdown menus 8
Manual Mode 29
microSD cards 5
Mute Audio 45
Bearings 43
Browse Files 46
C
I
N
Cancel navigation 36
Chart 41
Chart Data 41
Installation menu 30
Navigating a route 35
Navigating a trail 39
Navigation 42
E
Editing waypoints 33
Index | Elite-5 HDI
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigation menu 42
New Waypoint 31
NMEA 0183 47
Reset Fishing Mode 29
Reset water distance
30
Route display 42
Routes Screen 34
Split Zoom 26
Standby mode 11
Steer Page 12
Stop Sonar 21, 27
Surface Clarity 20, 26
System settings 44
Units 47
Upper and Lower Limits
19, 24
Noise Rejection 20, 26
W
O
WAAS/MSAS/EGNOS
45
Waypoint display 42
Waypoints, Routes,
Trails 32
S
Off Course alarm 47
Off Course Distance 43
On/Off features 8
Orientation 40
T
Saving Screenshots 46
Scrollbars 8
Selecting a GPS Source
4
Temperature calibra-
tion 30
Text entry 9
Overlay Data 15, 21, 40
Working with menus 8
Configure 15
Customizing 16
Show 15
Sensitivity 24
Time 45
Setup wizard 6
Shallow alarm 47
Software Updates 46
Sonar Installation 30
Sonar Menu 22
Sonar Options menu
26
Sonar Page 12
Sonar settings 28
Sort waypoints 34
Split Flasher 26
Trackback 17
Trail display 42
Trails Screen 38
Turn unit on/off 4
P
Page menus 6
Page selection 6
Ping Speed 25
U
Unit Controls 4
R
Range 19
Index | Elite-5 HDI
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Databases Limited Warranty
Navico Databases License Agreement
“We”, “our”, or “us” refers to Navico, the manufacturer of this product. “You” or “your”
refers to the first person who purchases the product as a consumer item for personal, family, or
household use. The Databases Limited Warranty applies to the one or more databases that your
product may contain. We refer to each of these as a “Database” or together as the “Databases.”
Your product may thus include the “WBS Database” which contains worldwide background
surface mapping data, the “Indigo Database” which contains inland mapping data, or other
Databases.
We warrant to you that we have accurately compiled, processed, and reproduced the portions
of the source material on which the Databases are based. However, we are under no obliga-
tion to provide updates to the Databases, and the data contained in the Databases may be
incomplete when compared to the source material. WE MAKE NO EXPRESS OR IMPLIED
WARRANTY OF ANY KIND ABOUT THE ACCURACY OF THE SOURCE MATERIAL
ITSELF, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS IS A LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST PURCHASES
THIS PRODUCT AS A CONSUMER ITEM FOR PERSONAL, FAMILY, OR HOUSEHOLD
USE (“YOU”) AND NAVICO, THE MANUFACTURER OF THIS PRODUCT (“WE”,
“OUR”, OR “US”).
USING THE PRODUCT ACCOMPANIED BY THIS LICENSE AGREEMENT
CONSTITUTES ACCEPTANCE OF THESE TERMS AND CONDITIONS.
IF YOU DO NOT ACCEPT ALL TERMS AND CONDITIONS, PROMPTLY RETURN
THE PRODUCT WITHIN 30 DAYS OF PURCHASE. PLEASE RETURN USING THE
ENCLOSED UPS SHIPPING LABEL AND INCLUDE: PROOF OF PURCHASE, NAME,
ADDRESS, AND PHONE NUMBER. YOUR PURCHASE PRICE AND ANY APPLICABLE
TAXES WILL BE REFUNDED. PLEASE ALLOW 4-6 WEEKS TO PROCESS YOUR
REFUND.
1.
This License Agreement applies to the one or more databases that your product
may contain. We refer to these singly as a “Database” and together as the “Da-
tabases.” Your product may thus include the “WBS Database” which contains
worldwide background surface mapping data, the “Indigo Database” which
contains inland mapping data, or other Databases.
If there is a defect in any Database, your exclusive remedy shall be, at our option, either a
refund of the price you paid for the product containing the defective Database or a replacement
of such product. WE WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANY-
ONE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR OTHER INDIRECT
DAMAGE OF ANY KIND.
2.
The Databases that your product may contain are licensed, not sold. We grant
to you the nonexclusive, nonassignable right to use these Databases for supple-
mental navigation reference purposes, but only as long as you comply with
the terms and conditions of this License Agreement. We reserve the right to
terminate this license if you violate any aspect of this License Agreement. You
are responsible for using official government charts and prudent navigation for
safe travel.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusions may not apply to you.
This warranty does NOT apply in the following circumstances: (1) when the product has
been serviced or repaired by anyone other than us; (2) when the product has been connected,
installed, combined, altered, adjusted, or handled in a manner other than according to the
instructions furnished with the product; (3) when any serial number has been effaced, altered,
or removed; or (4) when any defect, problem, loss, or damage has resulted from any accident,
misuse, negligence, or carelessness, or from any failure to provide reasonable and necessary
maintenance in accordance with the instructions of the owner’s manual for the product.
We reserve the right to make changes or improvements in our products from time to time
without incurring the obligation to install such improvements or changes on equipment or
items previously manufactured.
This warranty gives you specific legal rights and you may also have other rights which may
vary from state to state.
Your remedies under this warranty will be available so long as you can show in a reasonable
manner that the defect occurred within one (1) year from the date of your original purchase,
and we must receive your warranty claim no later than 30 days after such 1-year period
expires. Your claim must be substantiated by a dated sales receipt or sales slip.
3.
4.
The Databases housed in your product are protected by the copyright notices
appearing on the product or its screen(s). You may NOT modify, adapt, trans-
late, reverse engineer, decompile, disassemble, rent, lease, or resell any Data-
base, and you may NOT create derivative works based upon any Database or its
contents. Any unauthorized reproduction, use, or transfer of a Database may be
a crime and may subject you to damages and attorney fees.
This License Agreement will terminate immediately without prior notice from
us if you fail to comply with or violate any of the provisions of this Agreement.
Upon termination, you will promptly return all products containing one or more
Databases to us.
5.
6.
Prices and programs are subject to change without notice.
This LicenseAgreement shall be governed by the laws of the State of Oklahoma
and comprises the complete and exclusive understanding between you and us
concerning the above subject matter.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact information
Customer Service:
1-800-628-4487
(8 a.m. to 5 p.m. Central Standard Time, M-F)
(Canada)
1-855-361-1564
(8 a.m. to 5 p.m. Eastern Standard Time, M-F)
Ordering Accessories
Visit our website
Download from Www.Somanuals.com. All Manuals Search And Download.
Visit our website:
*988-10518-001*
N2584
Download from Www.Somanuals.com. All Manuals Search And Download.
|