English
Español
Nederlands
EXOTIK PRE-AMPLIFIER
Owner's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Important Safety Information
UK USERS PLEASE READ THIS
CE Declaration of Conformity
Linn Products Ltd declare that this product is in conformance with the Low Voltage Directive 73/23/EEC and
Electromagnetic Compatibility 89/336/EEC as amended by 92/31/EEC and 93/68/EEC.
IMPORTANT SAFETY INFORMATION
Fuse replacement
This appliance is fitted with a non-rewireable 13 Amp mains plug. The plug contains a
5 Amp fuse. If the fuse has blown it can be replaced as follows:
The conformity of the designated product with the provisions of Directive number 73/23/EEC (LVD) is proved by
full compliance with the following standards:
a) Pull out the red fuse cover/carrier.
Standard number
EN60065
Date of issue
2002
Test type
General requirements
b) Remove and dispose of the blown fuse.
Marking
Hazardous radiation
Heating under normal conditions
Shock hazards under normal
operating conditions
c) Fit a new 5 Amp BS1362 approved fuse into the carrier and push the carrier
back into the plug.
Insulation requirements
Fault conditions
Mechanical strength
Parts connected to the mains supply
Components
Terminal devices
Always ensure the fuse cover is fitted. If the fuse cover is missing do not use the plug.
Contact your Linn retailer to obtain a replacement fuse cover.
Fuses are for fire protection and do not protect against electric shock.
External flexible cords
Electrical connections and mechanical fixings
Protection against electric shock
Stability and mechanical hazards
Resistance to fire
Mains plug replacement
Should your mains plug need replacing and you are competent to do this proceed as
follows. If you are in doubt contact your Linn retailer or a competent electrician.
a) Disconnect the plug from the mains supply.
The conformity of the designated product with the provisions of Directive number 89/336/EEC (EMC) is proved by
full compliance with the following standards:
b) Cut off the plug and dispose of it safely. A plug with bared conductors is
dangerous if engaged in a live socket.
Standard number
EN55013
EN55013
Date of issue
2001
2001
Test type
Conducted emissions
Absorbed emissions
Immunity
c) Only fit a 13 Amp BS1363A approved plug with a 5 Amp fuse.
EN55020
2002
d) The cable wire colours or a letter will be marked at the connection points of most
quality plugs.
FCC notice
NOTE:
Attach the wires securely to their respective points. The Brown wire must go to the Live
pin, the Blue wire must go to the Neutral pin, and the Green/Yellow wire must go to the
Earth pin.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
e) Before replacing the plug top ensure that the cable restraint is holding the outer
sheath of the cable firmly and that the wires are correctly connected.
WARNING
THIS APPLIANCE MUST BE EARTHED.
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
EXOTIK PRE-AMPLIFIER
Owner’s Manual
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Copyright and Acknowledgements
Copyright and Acknowledgements
Copyright © 2004 Linn Products Ltd. First edition April 2004.
Linn Products Limited, Glasgow Road, Waterfoot, Eaglesham, Glasgow, G76 OEQ,
Scotland, United Kingdom
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of the
publisher.
Printed in the United Kingdom.
Trade marks used in this publication: Linn and the Linn logo are registered trade marks
of Linn Products Limited. EXOTIK, UNIDISK, KLIMAX, LIMBIK and KNEKT are trade
marks of Linn Products Limited.
EXOTIK+DA additional acknowledgements:
"DTS", "DTS-ES" and “DTS 96/24” are trade marks of Digital Theater Systems, Inc.
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the
double-D symbol are trade marks of Dolby Laboratories.
The content of this manual is furnished for information use only, is subject to change
without notice, and should not be construed as a commitment by Linn Products Limited.
Linn Products Limited assumes no responsibility or liability for any errors or
inaccuracies that may appear in this manual.
Linn Products Limited disclaims any proprietary interest in trade marks and trade names
other than its own.
EXOTIK PRE-AMPLIFIER
Owner’s Manual
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Contents
Contents
Operation
17
17
17
17
17
Introduction
1
1
1
Standby key
Audio formats (EXOTIK+DA)
Cleaning
Selecting a source
Adjusting the audio
Volume
Connecting
2
2
2
2
3
Unpacking
Connecting to the mains supply
Positioning
Balance
17
Volume trim
17
Lip Sync Delay (EXOTIK+DA)
Surround sound formats
Midnight Movie mode (EXOTIK+DA)
Restoring the original audio settings
Record function
18
18
20
20
21
Back panel
Front Panel and Handset
Front panel display
Front panel layout
Handset
4
4
4
5
Technical Specification
Guarantee and Service
22
23
Setup
6
6
6
7
Connecting
Setup menus
Using the setup menus
Speaker Setup
7
Source Setup
9
Audio Setup
11
General Setup
12
15
16
Installer Menu
Using the EXOTIK with a Linn UNIDISK player
EXOTIK PRE-AMPLIFIER
Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Introduction
Audio formats (EXOTIK+DA)
Introduction
The surround sound algorithms supplied with the EXOTIK+DA include:
The EXOTIK pre-amplifier has been designed to provide superb audio performance with
both two- and multi-channel source material. This product uses technology developed
for Linn’s award-winning flagship KLIMAX Kontrol pre-amplifier and offers purist audio
performance and access to and control of the new generation of multi-channel sound
formats.
Dolby Pro Logic II, Dolby Digital EX
Two variants of the product offer different levels of functionality to suit your
requirements:
DTS 96/24, DTS-ES
The standard EXOTIK is a multi-channel analogue unit supporting bass redirect, stereo
sub algorithm and 5.1 to 2 channel downmix.
Along with Linn’s proprietary LIMBIK algorithm.
Note:
A full list of the algorithms is detailed in the Surround sound formats section of the
Operation chapter.
EXOTIK+DA is an enhanced product which offers all the features of the standard EXOTIK
with the addition of a digital audio module for processing of all major audio algorithms,
including Dolby Digital 5.1, Pro Logic II, DTS Surround and DTS 96/24.*
The EXOTIK pre-amplifier exemplifies a commitment by Linn to new products which can
take advantage of the latest technology and audio formats whilst continuing to support
existing Linn customers with improved performance and superb value.
Cleaning
Disconnect the EXOTIK from the power supply before cleaning. Remove dust and
fingerprints with a soft, dry cloth. Avoid using domestic cleaning products on the unit.
Important notes:
When the unit is in standby, either EXOTIK or EXOTIK+DA is shown on the front panel
display to indicate the product variant.
In this manual ‘EXOTIK’ refers to both the standard and the EXOTIK+DA versions of the
product. ‘Standard EXOTIK’ and ‘EXOTIK+DA’ refer specifically to the variants.
*The digital audio module is available as an upgrade for the standard EXOTIK.
EXOTIK PRE-AMPLIFIER
Owner’s Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Connecting
Positioning
Connecting
You can locate your EXOTIK anywhere you find convenient (including in a 19” rack), but
there are a few simple points to note regarding positioning:
This chapter explains how to install the EXOTIK pre-amplifier into your hi-fi/AV system.
●
The IR sensor that receives the handset signals is quite sensitive, so the unit
should be kept out of direct sunlight to avoid false operation. The IR beam from
the handset will pass through semi-opaque glass so operation behind, for example,
smoked-glass cabinet doors is possible.
Unpacking
The EXOTIK is supplied with the following accessories:
●
●
●
●
luminescent handset with booklet
2 x R03 (AAA) batteries for the handset
1 pair of black interconnect cables
●
●
Never block the ventilation slots on the top and sides of the unit.
The unit should be protected from anything that generates significant amounts of
heat, such as radiators or power amplifiers.
RS232 lead (for connecting the EXOTIK to a Linn UNIDISK player to allow
communication between the two units)
●
●
mains lead
this manual
We recommend you retain the packaging for reuse in case you need to transport the unit
at any time.
Connecting to the mains supply
Manual voltage selection is not required as the EXOTIK operates from any mains AC
power. There are no user-replaceable fuses inside the unit. The mains lead supplied may
be fitted with a fused plug according to local regulations. If this is the case, always
replace this fuse with another of the same type and rating.
The EXOTIK must always be earthed when connected to the mains supply. Use
the earthed mains lead supplied. Never use an unearthed plug or adapter with
this unit.
EXOTIK PRE-AMPLIFIER
Owner’s Manual
2
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Connecting
Back panel
1
2
POWER
OFF
ON
SEE UNDERSIDE FOR SAFETY DETAILS
1
3
MAIN
L
OUT RS232 IN
L
L
1
2
IN
FRONT
SURR
SURR BK
CENTRE
SUB
1/FRONT
2/SURR
3/CENTRE
SUB
4
5
6
1
2
3
R
R
R
5.1 GROUP
OUT
REMOTE
OUTSPDIF
TOSLINK
OUT
1
INPUTS
2
3
2
4
ACC/RCU
IR
ANALOGUE AUDIO OUTPUTS
TAPE OUT
ANALOGUE AUDIO INPUTS
*
*
13
12
11
10
9
8
7
6
5
4
3
Connector group name: Connection function
Connector marking
Connector
type
Connector group name:
Connector marking
Connection function
Connector
type
OFF, ON
Mains power switch
Mains power inlet
-
1
8
ANALOGUE AUDIO
OUTPUTS: FRONT L-R,
SURR L-R, SURR BK
L-R, CENTRE, SUB
One 7.1 analogue audio output. The SURR outputs
are for connection to the two surround
8 x RCA
2
3
No name or marking
IEC
loudspeakers in a 5.1 system. The SURR BK outputs
are for connection to the two additional loudspeakers
in a 7.1 system - located at the rear of the room.
For two-channel systems, use the FRONT outputs
(and SUB if required) only
*
*
TOSLINK: OUT,
INPUTS 1 to 3
One optical digital audio output and three inputs
4 x TOSLINK
SPDIF: OUT, INPUTS
1 to 3
One electrical digital audio output and three inputs 4 x RCA
4
5
9
REMOTE: IN, OUT
ACC/RCU
RC5 in/out local loop for use in a KNEKT system
2 x RCA
1 x RJ45
ANALOGUE AUDIO
INPUTS: 4 L-R, 5 L-R,
6 L-R
Three stereo analogue L-R audio inputs
6 x RCA
6 x RCA
10
For installing the EXOTIK in a KNEKT
system or for connection to an infrared repeater
ANALOGUE AUDIO
One 5.1 analogue audio input or three stereo
analogue L-R audio inputs
6
7
11
12
13
1 to 4, MAIN
IR: 1, 2
Used if the EXOTIK is part of a KNEKT system
Pass IR commands to auxiliary devices
5 x RJ45
INPUTS: 5.1 GROUP -
1/FRONT L-R, 2/SURR
L-R, 3/CENTRE L, SUB R
2 x 3.5 mm jack
2 x RJ12
RS232: IN, OUT
Pass control instructions to and from the EXOTIK.
The OUT connection is used if you want to let
the EXOTIK control another device e.g. a Linn
UNIDISK player. The IN connection is used
if you want to control the EXOTIK from a third-
party home theatre controller
TAPE OUT: L-R
One analogue L-R output for connection to a
recording device e.g. DAT recorder
2 x RCA
*EXOTIK+DA
Switch off the EXOTIK before connecting plugs to, or disconnecting plugs from, the
back panel to avoid generating an electrical surge that may damage the unit or other
components of your AV system.
Using the EXOTIK with a Linn UNIDISK player
For information on how to connect and set up your EXOTIK to a Linn UNIDISK player,
see the section at the end of the Setup chapter.
EXOTIK PRE-AMPLIFIER
Owner’s Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Front Panel and Handset
Front Panel and Handset
Front panel display
The front panel display shows you information regarding what you are listening to.
The current volume, current source, or both can be displayed along with the input audio
signal and processing algorithm.
The display also shows the setup menus and other information depending on the current
operation.
Front panel layout
2
1
4
3
5
Front panel display
SELECT Selects/executes options and certain commands. Used for accessing Setup Menus
SOURCE - / +,
Change source, for adjusting settings
(standby) Brings unit out of, or puts into, standby mode
1
2
3
4
5
/
VOLUME - / +,
/
Adjust the volume level, navigate setup menus and adjust settings
EXOTIK PRE-AMPLIFIER
Owner’s Manual
4
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Front Panel and Handset
Handset
10
11
1
AUDIO ADJ Adjusts loudspeaker balance and trim
LIP SYNC Adds time delay to the audio signal*
2
1
2
3
(mute) Mutes/unmutes the audio output
4SURR Selects a surround sound format
3
5
VOL - / + Adjust the volume level
6
4
5
6
CD Selects a CD source
12
13
7
AUX Selects an auxiliary source
8
9SETUP Enters/exits the setup menus
(standby) Brings unit out of, or puts into, standby mode
TV Puts handset into TV mode
For navigating setup menus and adjusting settings
7
8
14
15
10
11
TUNER Selects a tuner source
12
9
. DVD Selects a DVD source
13
‘enter’ Selects/executes options and certain commands.
Is used for accessing Setup Menus
14
15
(record) For setting up a record path
16 KNEKT keys Used if the unit is installed in a KNEKT system
Keys and functions not listed above do not function with the
EXOTIK but may with other Linn products.
16
Note:
If your EXOTIK is not responding as expected to handset keys, it is
likely that the handset is in TV mode. To correct this press any of
the source keys (DVD, CD, TUNER or AUX) on the handset.
*EXOTIK+DA
EXOTIK PRE-AMPLIFIER
Owner’s Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Setup
Setup menus
Setup
The setup menus enable you to configure your EXOTIK for all sources it is connected to,
the loudspeakers in your system and much more. To take advantage of your EXOTIK’s
features, please take the time to configure your unit correctly.
Connecting
The first stage in setting up your EXOTIK is to connect your sources, power amp(s) and
other peripheral devices to the EXOTIK.
The setup menus are divided into four categories and are accessed via the MAIN MENU:
1. Ensure your EXOTIK and all components that you will be connecting to the EXOTIK
are disconnected from the mains supply.
SPEAKER SETUP
For configuring the unit for the number and size of the loudspeakers in your system and
for calibrating their volume level. (EXOTIK+DA: also for setting the distance of your
loudspeakers from your listening position.)
2. Connect your source components, power amp(s) and any communication/control
devices you wish to use, referring to the back panel diagram in the Connecting
chapter.
SOURCE SETUP
For configuring sources on the unit.
3. Connect the EXOTIK to the mains supply and turn the unit on using the switch on
the back panel. The front panel will display EXOTIK or EXOTIK+DA, depending on
your unit.
AUDIO SETUP
For configuring the audio output of the unit.
4. Press the
key on the front panel or handset.
GENERAL SETUP
For adjusting the general setup of the unit.
The main stage in setup is configuring the EXOTIK pre-amplifier to suit your
requirements. This is achieved using the setup menus. How to configure the EXOTIK is
explained in the rest of this chapter.
There is also a UNIDISK SETUP item in the MAIN MENU for accessing the setup menus
on a Linn UNIDISK player if one is present (see Using the EXOTIK with a Linn UNIDISK
player, end of this chapter).
In addition, the EXOTIK features an INSTALLER MENU for saving the configuration of the
unit as set in the above menus and restoring the factory defaults. For full information
see Installer menu, this chapter.
EXOTIK PRE-AMPLIFIER
Owner’s Manual
6
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Setup
Using the setup menus
To access the setup menus:
Either
Speaker setup
●
or
●
Press SETUP on the handset.
SIZE
Accesses the SPEAKER SIZE sub-menu.
Hold SELECT on the front panel until MAIN MENU / SPEAKER SETUP is shown on
the display.
For all loudspeakers in your system (except a subwoofer) you must inform the
EXOTIK whether the speakers are LARGE or SMALL. These settings refer to the
frequency response of the loudspeakers, not to their physical size.
Standard EXOTIK
For loudspeakers that operate below 100 Hz, select LARGE.
For loudspeakers that do not operate below 100 Hz, select SMALL. Frequencies in
the audio signal that are below 100 Hz will be routed to a subwoofer, if present, or
any LARGE loudspeakers, if not.
To access the installer menu:
●
Hold SETUP on the handset or SELECT on the front panel until INSTALLER MENU
is shown on the display (approximately 5 seconds).
SMALL FREQUENCY (EXOTIK+DA)
Select the operating frequency that your limited bass response (SMALL)
loudspeakers operate above. Frequencies in the audio signal that are below the
selected option will be routed to a subwoofer, if present, or any full-range
loudspeakers (LARGE), if not.
To navigate through the menus and options:
/
●
Use the
keys on the handset or front panel. Arrows on the display indicate
which key(s) can be used.
Options: 40 Hz, 60 Hz, 80 Hz, 100 Hz, 120 Hz
Default setting: 80 Hz
To make a selection:
●
Press ‘enter’ on the handset, or SELECT on the front panel.
FRONT*
Large front speakers (full-range frequency response), set to LARGE.
Small front speakers (limited bass response), set to SMALL.
To exit from the setup menus:
●
Press SETUP on the handset (if changes have been made you will be prompted to
save or not save the changes).
Default setting: LARGE
*For two-channel systems, use the FRONT item and set CENTRE, SURROUND and
SURROUND BACK to NONE.
EXOTIK PRE-AMPLIFIER
Owner’s Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Setup
CENTRE
DISTANCE (EXOTIK+DA)
Accesses the SPEAKER DISTANCE sub-menu.
Large centre speaker (full-range frequency response), set to LARGE.
Small centre speaker (limited bass response), set to SMALL.
No centre speaker, set to NONE.
DISTANCE UNITS
Select the units for loudspeaker distance measurements.
Default setting: LARGE
Options: FEET, METRES
Default setting: FEET
SURROUND
Large surround speakers (full-range frequency response), set to LARGE.
Small surround speakers (limited bass response), set to SMALL.
No surround speakers, set to NONE.
SPEAKER DISTANCE
Default setting: LARGE
In order to ensure that sound from all loudspeakers in your system reaches you at
the same time, you must inform the EXOTIK+DA as to the distance each speaker is
from your seating position. The EXOTIK+DA will then add a time delay to the
appropriate speakers.
SURROUND BACK
Large surround back speakers (full-range frequency response), set to LARGE.
Small surround back speakers (limited bass response), set to SMALL.
No surround back speakers, set to NONE.
Set the distance from your seating position for all speakers in your system.
Range: 1 ft (0.3 m) to 27 ft (8.2 m)
Default setting: 6 ft (1.8 m)
Default setting: LARGE
SUBWOOFER
Select SAVE to save your changes and return to the SPEAKER SETUP menu.
Select BACK to return to the SPEAKER SETUP menu without saving changes.
If you have connected a subwoofer, set to YES.
If you have not connected a subwoofer, set to NO.
Default setting: YES
Select EXIT to leave setup (if changes have been made and SAVE has not been
selected, you will be prompted to save or not save the changes).
Select SAVE to save your changes and return to the SPEAKER SETUP menu.
Select BACK to return to the SPEAKER SETUP menu without saving changes.
CALIBRATION
Accesses the SPEAKER CALIBRATION sub-menu.
Select EXIT to leave setup (if changes have been made and SAVE has not been
selected, you will be prompted to save or not save the changes).
SPEAKER CALIBRATION
If your audio system uses more than two loudspeakers and a subwoofer, you can use
the speaker calibration feature to ensure that the volume level that reaches your
seating position is the same for each loudspeaker (speaker calibration is not
required for two-channel systems). Calibration can be done by ear or by using an
SPL (Sound Pressure Level) meter.
EXOTIK PRE-AMPLIFIER
Owner’s Manual
8
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Setup
●
There are differences in the method of performing loudspeaker calibration on a standard
EXOTIK and an EXOTIK+DA:
To stop loudspeaker calibration, press SETUP on the handset or SELECT on
the front panel.
Standard EXOTIK
Range: -15 dB to 15 dB (in 0.5 steps)
Default setting: 0 dB
You will need a test disc that contains a tone signal for each loudspeaker in your system.
Your specialist Linn retailer may be able to supply you with a suitable disc.
Select SAVE to save your changes and return to the SPEAKER SETUP menu.
Select BACK to return to the SPEAKER SETUP menu without saving changes.
To perform speaker calibration:
●
Add a Linn UNIDISK player (or other multi-channel disc playing source) to the
EXOTIK by following the source setup instructions in the next section.
Select EXIT to leave setup (if changes have been made and SAVE has not been
selected, you will be prompted to save or not save the changes).
●
●
●
Exit setup and change source to the UNIDISK/multi-channel disc playing source.
Re-enter setup and return to the SPEAKER CALIBRATION sub-menu.
Select BACK to return to the MAIN MENU.
Select EXIT to leave Setup.
Play the tracks on the test disc for speaker calibration while selecting the
appropriate loudspeakers from the EXOTIK’s menu.
●
If the tone signal coming from a particular loudspeaker is louder or quieter
than from the other loudspeakers, use the
trim the volume as required.
keys on the handset to
/
Source setup
EXOTIK+DA
To perform speaker calibration:
●
●
Select REF. CALIBRATION LEVEL. Adjust the reference calibration level so
that the signal you hear is at a comfortable listening level (or reaches a
preset level on an SPL meter).
Select the back panel input you wish to use with your source component, or select ADD
UNIDISK* if you are adding a Linn UNIDISK player as a source component.** You must
complete the source setup procedure for each source component you are connecting to
your EXOTIK.
Select NOISE. Choose either WHITE (equal energy per frequency, bright
sounding) or PINK (equal energy per octave, richer in lower frequencies than
White).
Options: ANALOG GROUP, ANALOG 1 to 6, SPDIF 1 to 3*, TOS (TOSLINK) 1 to 3*,
KNEKT, ADD UNIDISK*
●
●
Select START. The signal will move round the loudspeakers in your system in
a clockwise direction and will be indicated on the display.
* EXOTIK+DA
**If you wish to connect a UNIDISK player to a standard EXOTIK use the ANALOG
GROUP inputs (for multi-channel systems) or a stereo input pair (for two-channel
systems).
When the signal reaches a loudspeaker which is louder or quieter than the
other loudspeakers, use the
as required. A few seconds after the
signal will continue its clockwise direction.
keys on the handset to trim the volume
/
or key has been released the
EXOTIK PRE-AMPLIFIER
Owner’s Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Setup
NAME
TYPE
Select a type for this source. This is the type that appears on Linn learning
handsets.
You are able to give the source a name which will be shown on the display when that
source is selected.
Options: AUX, CD, DVD*, TUNER, PHONO 1/LASER, PHONO 2/AUX, TAPE 1, TAPE
2/VCR, DAT, TV, CABLE, SATELLITE, NONE.
To change the flashing character:
●
Repeatedly press or hold
/
on the handset or front panel.
Default setting: AUX (Except ANALOG 2 and 3, and KNEKT which are set to NONE)
*DVD is the only option available for the ADD UNIDISK source.
The following characters are available: A to Z, 0 to 9, space.
To move to the next or previous character:
Notes:
For ease of use with the handset supplied with the unit, you may wish to restrict the
type selected to either CD, DVD, TUNER or AUX, to allow direct source selection.
●
Press or
.
If you do not wish to use a particular back panel input, set Type to NONE. This
means that when you are using the SOURCE -/+ keys on the front panel to select a
source, inputs set to NONE will not be seen.
When you have finished inputting the name, press ‘enter’ or SELECT.
Default setting: (name of back panel connector or ‘UNIDISK’)
Note:
VOLUME OFFSET
The name can be up to twelve characters long.
Volume offset is for adjusting the volume of a source in comparison to other
sources. You may want to adjust the volume offset for a source if, for example, your
tuner sounds quieter than your CD player when played at the same volume setting.
The next two items are for use if ADD UNIDISK has been selected from the source
setup options. For the other source setup options these items will not be shown.
Range: -15 to 15 (in 0.5 steps). No volume offset equals 0.
Default setting: 0
ANALOG INPUT
Select which analogue input(s) is/are connected to the UNIDISK player.
Options: ANALOG GROUP, ANALOG 1 to 6
Default setting: ANALOG GROUP
DIGITAL INPUT
Select which digital input is connected to the UNIDISK player.
Options: SPDIF 1 to 3, TOSLINK 1 to 3
Default setting: SPDIF 1
EXOTIK PRE-AMPLIFIER
Owner’s Manual
10
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Setup
SURROUND CHANNELS
MUTE RATE
If you are setting up the ANALOG GROUP source or are adding a Linn UNIDISK
player and have a 7.1 speaker configuration, you are able to select whether to use
your side surround or back surround speakers when listening to a 5.1 channel audio
source.
Set the speed at which the EXOTIK mutes or unmutes the volume when
when changing sources.
is pressed, or
Range: 1/10 (slowest) to 10/10 (fastest)
Default setting: 6/10
Set to SURROUND to send the surround signal to your side surround speakers.
Set to SURROUND BACK to send the surround signal to your back surround
speakers.
VOLUME LIMIT
Default setting: SURROUND
Set the maximum volume level of the EXOTIK.
Range: 0 to 100 (in 0.5 steps)
Default setting: 100
Select SAVE to save your changes and return to the SOURCE SETUP menu.
Select BACK to return to the SOURCE SETUP menu without saving changes.
VOLUME PRESET
Select EXIT to leave setup (if changes have been made and SAVE has not been
selected, you will be prompted to save or not save the changes).
Set the volume level of the EXOTIK when it is brought out of standby.
The setting cannot be higher than the Volume Limit setting (see above).
Select BACK to return to the MAIN MENU.
Select EXIT to leave setup.
Range: 0 to 100 (in 0.5 steps)
Default setting: 40
MIDNIGHT MOVIE (EXOTIK+DA)
Audio setup
Midnight Movie mode optimises the audio of any source for listening at a reduced
volume.
Midnight Movie mode increases the level of quiet sections (e.g. whispered dialogue in a
movie) and reduces the peaks of loud sections (e.g. action scenes in a movie) but without
restricting the overall dynamics of the original audio signal.
It is turned on/off by pressing and holding SURR on the handset.
Options: LOW (least effective), MEDIUM, HIGH (most effective)
Default setting: LOW
VOLUME RATE
Set the speed at which the EXOTIK changes volume when VOL +/VOL - is pressed.
Range: 1/10 (slowest) to 10/10 (fastest)
Default setting: 6/10
EXOTIK PRE-AMPLIFIER
Owner’s Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Setup
Select SAVE to save your changes and return to the AUDIO OPTIONS menu.
Select BACK to return to the AUDIO OPTIONS menu without saving changes.
DOLBY PRO LOGIC II MUSIC (EXOTIK+DA)
Dolby Pro Logic II is an audio signal processing algorithm that converts a two-channel
audio signal to a five-channel audio signal.
Dolby Pro Logic II Music is a mode of Dolby Pro Logic II that is particularly suited to
music. It features three user-adjustable parameters that are accessed from this item.
Select EXIT to leave setup (if changes have been made and SAVE has not been
selected, you will be prompted to save or not save the changes).
CENTRE WIDTH
Select SAVE to save your changes and return to the MAIN MENU.
Select BACK to return to the MAIN MENU without saving changes.
This parameter allows adjustment of the audio signal between the centre
loudspeaker and front left and right loudspeakers.
If set to 0 (no spreading) all of the audio signal for the centre channel is sent to the
centre loudspeaker.
If set to 3 (neutral) a portion of the centre channel signal is also sent to the left and
right front loudspeakers.
Select EXIT to leave setup (if changes have been made and SAVE has not been selected,
you will be prompted to save or not save the changes).
If set to 7 (Full Phantom) all of the centre channel signal is split evenly between the
front left and right loudspeakers.
General setup
Range: 0 to 7
Default setting: 3
PANORAMA CONTROL
If set to ON, the Panorama control extends the audio signal from the front left and
right loudspeakers to include the surround left and right loudspeakers. This adds a
"wraparound" effect to the sound.
DISPLAY INTENSITY
Set the brightness of the front panel display.
Options: ON, OFF
Options: LOW, MEDIUM, HIGH
Default setting: MEDIUM
Default setting: OFF
DIMENSION CONTROL
DISPLAY CONTENT
This parameter allows you to shift the balance between the front and rear
loudspeakers. Positive values move the sound towards the front, negative values
towards the rear.
Set what information you want displayed on the unit’s front panel when it is in normal
operation.
If a recording is too spacious or strong from the surround loudspeakers it can be
shifted "forward" to get a better balance. A stereo recording can be shifted
"backward" to make the sound more enveloping.
Options: LAST USED (source or volume), (current) SOURCE AND VOLUME, VOLUME,
(current) SOURCE
Default setting: SOURCE AND VOLUME
Range: -3 (most rear) to 3 (most front)
Default setting: 0 (neutral)
EXOTIK PRE-AMPLIFIER
Owner’s Manual
12
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Setup
DISPLAY TIMEOUT
STANDBY RECORD FROM
Set the time that new volume or source information is shown for before unit returns to
its Display Content (see above).
You can record from a source component to a recording device through the EXOTIK,
even if the EXOTIK is in standby mode.
Range: 1 SEC. to 10 SEC.
Default setting: 4 SEC.
Set which source configuration you want the EXOTIK to select when it is in standby.
Options: LAST USED, NONE, (any of the source inputs), AS KNEKT*
Default setting: LAST USED
SELECTION TIMEOUT
When the source is changed, this item sets the time the EXOTIK takes before the new
source is selected.
KNEKT
If your EXOTIK is installed in a Linn KNEKT multi-room system, select the appropriate
setting. If your EXOTIK is not installed in a KNEKT system, select NONE.
Range: 1 SEC. to 10 SEC.
Default setting: 4 SEC.
Options: NONE, MAIN ROOM, LOCAL ROOM, INTERSEKT
Default setting: NONE
SLEEP TIMEOUT
Set the time elapsed before the front panel display enters sleep mode (i.e. shows three
dots) after a key on the front panel or handset is pressed.
ACCESSORY SOCKET
Define the use of the accessory (ACC/RCU) socket on the back panel.
Options: NEVER SLEEP, IMMEDIATE, 30 SEC., 5 MINS.
Default setting: NEVER SLEEP
Options: RCU* (KNEKT Room Control Unit), IR (Infrared Repeater)
Default setting: RCU
STARTUP SOURCE
PRODUCT IR
Set the source the unit selects when brought out of standby.
Enable or disable the infrared receiver on the front of the unit.
Options: LAST USED, NONE, (any of the source inputs)
Default setting: LAST USED
Options: ENABLE, DISABLE
Default setting: ENABLE
*For use with Linn KNEKT systems.
EXOTIK PRE-AMPLIFIER
Owner’s Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Setup
STOP BITS
RS232 EVENTS
If set to ENABLE, the unit passes information regarding its internal status to an external
device that accepts RS232 data.
Set the stop bits to suit the RS232 protocol being used.
Options: 1, 2
Options: ENABLE, DISABLE
Default setting: DISABLE
Default setting: 1
RS232 Setup
Select SAVE to save your changes and return to the GENERAL SETUP menu.
Select BACK to return to the GENERAL SETUP menu without saving changes.
Accesses the RS232 SETUP sub-menu.
The RS232 Setup sub-menu is for use if the EXOTIK is communicating with other RS232
enabled products (e.g. a third-party controller).
Select EXIT to leave setup (if changes have been made and SAVE has not been
selected, you will be prompted to save or not save the changes).
BAUD RATE
Select SAVE to save your changes and return to the MAIN MENU.
Select BACK to return to the MAIN MENU without saving changes.
Set the baud rate to suit the RS232 protocol being used.
Range: 1200 to 230400 (11 settings)
Default setting: 9600
Select EXIT to leave setup (if changes have been made and SAVE has not been selected,
you will be prompted to save or not save the changes).
PARITY
Set parity to suit the RS232 protocol being used.
Options: EVEN, ODD
Default setting: EVEN
DATA BITS
Set the data bits to suit the RS232 protocol being used.
Options: 7, 8
Default setting: 7
EXOTIK PRE-AMPLIFIER
Owner’s Manual
14
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Setup
Installer menu
To access the Installer menu:
●
Hold SETUP on the handset or SELECT on the front panel until INSTALLER MENU
is shown on the display (approximately 5 seconds).
SAVE AS INSTALLER
After the EXOTIK has been set up you can save the settings by selecting this item. The
saved Installer configuration can be restored at any time should the EXOTIK’s setup be
changed (see below). Any alterations to the product’s setup that you wish to keep as a
new Installer configuration can be stored by selecting this item, which will overwrite the
existing Installer configuration.
RESTORE INSTALLER
If you have made changes to the setup of the EXOTIK that you do not wish to keep, use
this option to restore the Installer configuration.
RESTORE FACTORY
Use this option to restore the default settings for all the setup menus.
SOFTWARE REVISION
This item informs the installer as to the version of the software installed on the EXOTIK.
Select EXIT to leave the Installer menu (if changes have been made you will be
prompted to save or not save the changes).
EXOTIK PRE-AMPLIFIER
Owner’s Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Setup
If you wish to use a Linn UNIDISK player with your EXOTIK, follow the instructions
below.
Using the EXOTIK with a Linn UNIDISK player
There are certain operational benefits available when using the EXOTIK with a Linn
UNIDISK player. These benefits are as follows:
1. Connect the audio outputs you wish to use from the UNIDISK player to the
corresponding inputs on the EXOTIK.
2. Connect the video outputs you wish to use from the UNIDISK player to your
display device.
Standard EXOTIK
●
You are able to use either your EXOTIK’s or UNIDISK player’s handset without
there being a conflict between the two products.
3. Connect the RS232 product-to-product lead (supplied with the EXOTIK) from the
EXOTIK’s RS232 OUT to the UNIDISK player’s RS232 IN.
●
You are able to access your UNIDISK player’s setup menus via the UNIDISK
SETUP option in the EXOTIK’s Main Menu setup items (i.e. the UNIDISK player’s
setup menus will appear on the display device it is connected to).
4. Connect the EXOTIK’s REMOTE OUT to the UNIDISK player’s REMOTE IN (you will
require an RCA phono-to-phono lead).
5. Enter User Options on your UNIDISK player.
Set –
EXOTIK+DA
●
When a disc is loaded into the UNIDISK player and the UNIDISK is selected as the
source on the EXOTIK+DA, the EXOTIK+DA will automatically switch to the
required input for the loaded disc.
Front Panel IR Command/Enable IR Commands to IGNORED or OFF
RS232 Events/Enable RS232 Events to ENABLED or ON
Baud Rate to 9600
(Also, for a UNIDISK SC set Knekt Mode to SOURCE.)
●
●
●
The EXOTIK+DA will choose an appropriate surround sound algorithm for the
disc’s audio stream.
6. Exit User Options.
You are able to use either your EXOTIK+DA’s or UNIDISK player’s handset without
there being a conflict between the two products.
7. Enter the GENERAL SETUP menu on the EXOTIK.
8. Enter the RS232 SETUP sub-menu.
Set –
You are able to access your UNIDISK player’s setup menus via the UNIDISK
SETUP option in the EXOTIK+DA’s Main Menu setup items (i.e. the UNIDISK
player’s setup menus will appear on the display device it is connected to).
Baud Rate to 9600
Parity to EVEN
Data Bits to 7
Stop Bits to 1
Save settings.
9. Add the UNIDISK in SOURCE SETUP (See Source setup earlier in this
chapter).
EXOTIK PRE-AMPLIFIER
Owner’s Manual
16
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Operation
Balance
Operation
To change the balance for all loudspeakers (excluding a centre speaker and/or
subwoofer):
Standby key
To toggle between standby mode and operation mode:
●
Press AUDIO ADJ (adjust) on the handset.
●
Press
on the front panel or handset.
BALANCE is shown on the front panel display.
●
Repeatedly press or hold to shift the balance to the right, or to shift the
balance to the left.
Selecting a source
To select the source you want to watch or listen to:
Either
Balance range is from 10 increments to the left to 10 increments to the right, with neutral
balance being 0.
●
●
●
Press the appropriate source type key (DVD, CD, TUNER or AUX) on the handset.
Use the keys to cycle through available sources of that type.
Volume trim
This feature is for use in systems that have more than two loudspeakers.
/
When listening to multi-channel audio or watching a DVD-Video, you may want to adjust
the volume level of your centre, surround, back surround loudspeakers or subwoofer
without affecting any of the other loudspeakers. This is done by adjusting volume trim.
When the desired source is shown on the front panel display, press ‘enter’, or wait
and the EXOTIK will select the source automatically.
or
To change the volume trim:
●
Repeatedly press the SOURCE +/- keys on the front panel. This will cycle through
all available sources.
●
Repeatedly press AUDIO ADJ (adjust) on the handset until the desired
loudspeaker(s) is/are shown on the front panel display.
●
When the desired source is shown on the front panel display, press SELECT, or
wait and the EXOTIK will select the source automatically.
●
Repeatedly press or hold
on the front panel or handset to
/
increase/decrease the level of volume trim.
Adjusting the audio
Volume
Volume trim range is from -10.0 to 10.0 (in 0.5 steps) with neutral trim being 0.
Note:
The loudspeakers shown when AUDIO ADJ is repeatedly pressed is dependent on the
number of loudspeakers in your system and the currently selected surround sound format.
To change the volume:
●
Repeatedly press or hold VOL -/ + on the front panel or handset.
Volume range is from 0 to 100 (in 0.5 steps).
EXOTIK PRE-AMPLIFIER
Owner’s Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Operation
The available surround sound formats, and a brief description of each, is as follows:
Surround sound format Description
Lip Sync Delay (EXOTIK+DA)
You may find with certain DVD-Videos that the movement of the actors’ lips and the
sound are not synchronized. You can correct this on the EXOTIK+DA using the Lip Sync
Delay feature.
Dolby Digital
A standard for storing 5.1 channels of audio signal
on to discs such as DVD-Videos
To adjust Lip Sync Delay:
Dolby Digital EX
Spreads the surround speaker portion of a Dolby
Digital 5.1 audio signal to two back speakers -
converting 5.1 audio to 7.1 audio
●
●
Press LIP SYNC on the handset.
Press
to increase/decrease the delay of the audio signal until the picture
/
Dolby Pro Logic II
Converts any non-surround sound audio signal into a
surround sound 5.0 signal
and audio are synchronized.
Lip Sync Delay range is from 0 to 250 milliseconds.
Dolby Pro Logic II Music Same as Dolby Pro Logic II but is particularly suited
to music. Features three user-adjustable parameters
that are accessed via the setup menus
Notes:
The setting for Lip Sync Delay is retained for that source.
DTS Digital Surround
DTS 96/24
A standard for storing 5.1 channels of audio signal on
to discs such as DVD-Videos
When adding Lip Sync Delay to an analogue source the audio must be converted from
the audio domain to the digital domain and back again. For this reason, the minimum
delay that can be applied to an analogue source is 5 milliseconds.
Same as DTS Digital Surround but offers better audio
quality
Surround sound formats
DTS ES Matrix
Spreads the surround speaker portion of a DTS 5.1
audio signal to two back speakers - converting 5.1
audio to 7.1 audio
The EXOTIK+DA is equipped with a wide range of surround sound formats to enhance
your audio/home cinema experience. The only surround sound format available on the
standard EXOTIK is Stereo Sub.
DTS ES Discrete
A standard for storing 6.1 channels of audio signal
on to discs such as DVD-Videos. On the EXOTIK the
extra channel can be spread over two back speakers -
converting 6.1 audio to 7.1 audio
To change the surround sound format:
●
Repeatedly press SURR on the handset until the desired format is shown on the
front panel display.
DTS 96/24 ES Matrix
Higher quality of DTS Digital Surround with the
addition of the surround sound speaker portion of
the signal being spread to two back speakers -
converting 5.1 audio to 7.1 audio
Phantom
3 Stereo
Passes the centre channel portion of a 5.1 or 7.1
audio signal to the front left and right speakers
Downmixes a 5.1 or 7.1 audio signal and passes it to
the front left and right, and centre speakers only
cont.
EXOTIK PRE-AMPLIFIER
Owner’s Manual
18
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Operation
The surround sound formats that are available for the different audio input and signal
types, are:
Surround sound format
Stereo Sub
Description
Downmixes a 5.1 audio signal to a two-channel
signal and then routes the signal to the front left and
right speakers and subwoofer
Analogue audio input
5.1 speakers in system
7.1 speakers in system
MPEG Stereo
A standard for storing two-channel audio in MPEG
files
Stereo
2.0
5.1
2.0
5.1
Analog 5.1
MPEG Surround
AAC Stereo
A standard for storing surround sound audio in
MPEG files
A standard for storing two-channel audio
A standard for storing surround sound audio
Two-channel audio input
AAC Surround
Limbik Party
Analogue
signal
PCM stereo
LtRt downmixed
signal
A Linn algorithm that sends essentially the same
audio signal to all speakers in your system
signal
Stereo
2.0
5.0
2.0
2.0
5.0
Depending on the audio signal coming in to the EXOTIK+DA and the number of speakers
in your system, two of the above formats can be combined to provide extra processing
e.g. Dolby Digital + Dolby Digital EX will convert a two-channel digital audio signal to 7.1
channels of audio (see table on page 20).
Dolby Pro Logic II
Dolby Pro Logic II Music
Limbik Party
5.0
5.0
5.0
5.0
5.1 & 7.1
2.1
5.1 & 7.1
2.1
5.1 & 7.1
2.1
Stereo Sub
EXOTIK PRE-AMPLIFIER
Owner’s Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Operation
Surround sound audio input
Midnight Movie mode (EXOTIK+DA)
Dolby
DTS
MPEG
AAC
This feature allows you to add compression to any multi-channel or 2-channel analogue
source. Adding compression reduces sudden increases in volume such as the sound of an
explosion on a DVD-Video.
Stereo
2.0
-
-
-
Phantom
2/2.1
2/2.1
2/2.1
2/2.1
To switch Midnight Movie mode on/off:
3 Stereo
3/0.1
3/0.1
3/0.1
3/0.1
●
Press and hold SURR on the handset.
Stereo Sub
2.1
2.1
2.1
2.1
When the mode is on, MIDNIGHT MOVIE or M/MOVIE is shown on the front panel display.
The amount of compression can be adjusted using the Midnight Movie item in the Audio
setup menu (see Setup chapter).
Dolby Digital
5.1
-
-
-
Dolby Digital + Dolby Digital EX
DTS Digital Surround
DTS 96/24
7.1
-
-
-
-
5.1
-
-
Restoring the original audio settings
-
5.1
-
-
To reset all the above audio items to their neutral/default settings:
DTS ES Matrix
-
7.1
-
-
●
Press and hold AUDIO ADJ on the handset until AUDIO SETTINGS RESET is
shown on the front panel display.
DTS ES Discrete
DTS 96/24 ES Matrix
MPEG Stereo
-
7.1
-
-
-
7.1
-
-
-
-
2.0
-
MPEG Surround
MPEG Surround + Dolby Digital EX
AAC Stereo
-
-
5.1
-
-
-
-
7.1
-
-
-
2.0
5.1
AAC Surround
-
-
-
AAC Surround + Dolby Digital EX
Limbik Party
-
-
-
7.1
5.1 & 7.1
5.1 & 7.1
5.1 & 7.1
5.1 & 7.1
Notes:
The available surround sound formats are dependent on the type of signal being
processed.
The default surround sound format for the current audio signal is shown in brackets on
the front panel display.
EXOTIK PRE-AMPLIFIER
Owner’s Manual
20
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Operation
Notes on the sources:
NO SOURCE: No record path will be set.
Record function
AS KNEKT: When a record path on the EXOTIK is being used, this setting will allow users
of a KNEKT Line Driver system to change the source they are listening to (which also
changes the record path). To protect a record path, select the required record option.
Once recording has finished, reselect the AS KNEKT option.
The record function allows you to route a source signal to a recording device such as a
VCR or DAT recorder.
The record functions available on your EXOTIK are dependent on whether your unit
includes, or does not include the digital audio module (if your unit has the digital audio
module EXOTIK+DA is shown on the front panel display when the unit is in standby
mode).*
Source inputs set to NONE will not be shown.
Additional step for an EXOTIK+DA:
The differences in record functionality between the two variants is shown below:
●
Use the
keys to select the record mode you want to use for making the
/
recording, then press ‘enter’.
Standard EXOTIK
Analogue Record Outputs
The available record modes are:
Analogue source
Any analogue source can be
routed to the analogue outputs
Option
Information
LtRt 44.1 kHz
LtRt 48 kHz
LtRt 88.2 kHz
LtRt 96 kHz
Choose the option that suits your recording device’s
operating frequency. (With these options, multi-channel
signals are downmixed to two channels)
EXOTIK+DA
Analogue Record Outputs
Any analogue source can be
Digital Record Outputs
Any analogue source can
LtRt As Input
Bit Perfect
Analog*
Output frequency is the same as the input frequency, and
multi-channel signals are downmixed to two channels
Analogue source
Digital source
routed to the analogue outputs be routed to the digital outputs
Output frequency is the same as the input frequency and
there is no processing of the signal
Only the digital source
currently being listened to can currently being listened to
be routed to the analogue can be routed to the
Only the digital source
Passes audio signals to the analogue outputs
outputs (drivers for the digital digital outputs
outputs are disabled)
*Analog is the only record mode available on the standard EXOTIK.
*The digital audio module is available as an upgrade to the standard EXOTIK.
To set a record path:
Notes:
The source audio signal is routed to either all of the analogue and/or all of the digital
outputs simultaneously. It is not necessary to specify which output you are using.
●
●
Press the
Use the
(record) key on the handset.
The available record modes are dependent on whether the input signal is analogue or
digital.
keys to select the source you want to record, then press ‘enter’.
/
For reasons of copyright defence some audio and video discs incorporate protection
systems that prevent them from being recorded.
EXOTIK PRE-AMPLIFIER
Owner’s Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Technical Specification
Technical Specification
Electrical
Mains voltage
100-230 Vac @ 50-60 Hz
Physical
Weight
3.5 kg, 7 lb 10 oz
Dimensions
381 (W) x 368 (D) x 80 (H) mm, 15” (W) x 14” (D) x 3” (H)
Signal Interfaces - Inputs
Type
Connector
Level
Impedance Notes
Digital electrical
(SPDIF)*
3 x RCA
500 mVp-p
75 Ω
-
-
Digital optical*
Unbalanced
3 x TOSLINK
12 x RCA
-
-
2 Vrms
10k Ω
Analogue
Signal Interfaces - Outputs
Type
Connector
Level
Impedance Notes
Digital electrical
(SPDIF)*
1 x RCA
500 mVp-p
-
75 Ω
-
-
Digital optical*
Unbalanced
Unbalanced
1 x TOSLINK
8 x RCA
2 x RCA
-
2 Vrms
2 Vrms
330 Ω
Surround outputs
Record outputs
330 Ω
Control Interfaces
Type
Port Name
Pin Connections
RS232
RS232
In
Rx = 3, Tx = 2, Ov = 5
Rx = 5, Tx = 4, Ov = 2
Out
*EXOTIK+DA
EXOTIK PRE-AMPLIFIER
Owner’s Manual
22
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Guarantee and Service
Linn Products Limited
Glasgow Road
Waterfoot
Eaglesham
Glasgow G76 0EQ
Scotland, UK
Guarantee and Service
This product is guaranteed under the conditions that apply in the country of purchase
and your statutory rights are not limited. In addition to any statutory rights you may
have, Linn undertake to replace any parts that have failed due to faulty manufacture.
To help us, please ask your Linn retailer about the Linn warranty scheme in operation in
your country.
Phone:
Fax:
Helpline:
Email:
+44 (0)141 307 7777
+44 (0)141 644 4262
0500 888909
In parts of Europe, the United States of America and some other markets, extended
warranty may be available to customers who register their purchase with Linn.
A warranty registration card is included with the product and should be stamped by your
retailer and returned to Linn as soon as possible. Alternatively, register your warranty
Website:
Linn Incorporated
8787 Perimeter Park Boulevard
Jacksonville
FL 32216
USA
Warning
Unauthorised servicing or dismantling of the product invalidates the manufacturer’s
warranty. There are no user serviceable parts inside the product and all enquiries
relating to product servicing should be referred to authorised retailers only.
Phone:
Fax:
Helpline:
Email:
+1 (904) 645 5242
+1 (904) 645 7275
888-671-LINN
Technical support and information
For technical support, product queries and information, please contact either your local
retailer or one of the Linn offices opposite.
Website:
Full details of your local retailer/distributor can be found on the Linn website:
Linn Deutschland GmbH
Albert-Einstein-Ring 19
22761 Hamburg
Important
Deutschland
●
Please keep a copy of the sales receipt to establish the purchase date of the
product.
Phone:
Fax:
Email:
Website:
+49-(0) 40-890 660-0
+49-(0) 40-890 660-29
●
Please ensure that your equipment is insured by you during any transit or
shipment for repair.
EXOTIK PRE-AMPLIFIER
Owner’s Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
|