Linn Stereo Amplifier EXOTIK PRE AMPLIFIER User Manual

English  
Français  
Deutsch  
Italiano  
EXOTIK PRE-AMPLIFIER  
Owner's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Important Safety Information  
UK USERS PLEASE READ THIS  
CE Declaration of Conformity  
Linn Products Ltd declare that this product is in conformance with the Low Voltage Directive 73/23/EEC and  
Electromagnetic Compatibility 89/336/EEC as amended by 92/31/EEC and 93/68/EEC.  
IMPORTANT SAFETY INFORMATION  
Fuse replacement  
This appliance is fitted with a non-rewireable 13 amp mains plug. The plug contains a  
5 amp fuse. If the fuse has blown it can be replaced as follows:  
The conformity of the designated product with the provisions of Directive number 73/23/EEC (LVD) is proved by  
full compliance with the following standards:  
a) Pull out the red fuse cover/carrier.  
Standard number  
EN60065  
Date of issue  
2002  
Test type  
General requirements  
b) Remove and dispose of the blown fuse.  
Marking  
Hazardous radiation  
Heating under normal conditions  
Shock hazards under normal  
operating conditions  
c) Fit a new 5 amp BS1362 approved fuse into the carrier and push the carrier  
back into the plug.  
Insulation requirements  
Fault conditions  
Mechanical strength  
Parts connected to the mains supply  
Components  
Terminal devices  
Always ensure the fuse cover is fitted. If the fuse cover is missing do not use the plug.  
Contact your Linn retailer to obtain a replacement fuse cover.  
Fuses are for fire protection and do not protect against electric shock.  
External flexible cords  
Electrical connections and mechanical fixings  
Protection against electric shock  
Stability and mechanical hazards  
Resistance to fire  
Mains plug replacement  
Should your mains plug need replacing and you are competent to do this proceed as  
follows. If you are in doubt contact your Linn retailer or a competent electrician.  
a) Disconnect the plug from the mains supply.  
The conformity of the designated product with the provisions of Directive number 89/336/EEC (EMC) is proved by  
full compliance with the following standards:  
b) Cut off the plug and dispose of it safely. A plug with bared conductors is  
dangerous if engaged in a live socket.  
Standard number  
EN55013  
EN55013  
Date of issue  
2001  
2001  
Test type  
Conducted emissions  
Absorbed emissions  
Immunity  
c) Only fit a 13 amp BS1363A approved plug with a 5 amp fuse.  
EN55020  
2002  
d) The cable wire colours or a letter will be marked at the connection points of most  
quality plugs.  
FCC notice  
NOTE:  
Attach the wires securely to their respective points. The Brown wire must go to the Live  
pin, the Blue wire must go to the Neutral pin, and the Green/Yellow wire must go to the  
Earth pin.  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part  
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the  
following measures:  
e) Before replacing the plug top ensure that the cable restraint is holding the outer  
sheath of the cable firmly and that the wires are correctly connected.  
WARNING  
THIS APPLIANCE MUST BE EARTHED.  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Copyright and Acknowledgements  
Copyright and Acknowledgements  
Copyright © 2004 Linn Products Ltd. First edition April 2004.  
Linn Products Limited, Glasgow Road, Waterfoot, Eaglesham, Glasgow, G76 OEQ,  
Scotland, United Kingdom  
All rights reserved. No part of this publication may be reproduced, stored in a retrieval  
system, or transmitted, in any form or by any means, electronic, mechanical,  
photocopying, recording, or otherwise, without the prior written permission of the  
publisher.  
Printed in the United Kingdom.  
Trade marks used in this publication: Linn and the Linn logo are registered trade marks  
of Linn Products Limited. EXOTIK, UNIDISK, KLIMAX, LIMBIK and KNEKT are trade  
marks of Linn Products Limited.  
EXOTIK+DA additional acknowledgements:  
"DTS", "DTS-ES" and “DTS 96/24” are trade marks of Digital Theater Systems, Inc.  
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the  
double-D symbol are trade marks of Dolby Laboratories.  
The content of this manual is furnished for information use only, is subject to change  
without notice, and should not be construed as a commitment by Linn Products Limited.  
Linn Products Limited assumes no responsibility or liability for any errors or  
inaccuracies that may appear in this manual.  
Linn Products Limited disclaims any proprietary interest in trade marks and trade names  
other than its own.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Contents  
Contents  
Operation  
17  
17  
17  
17  
17  
Introduction  
1
1
1
Standby key  
Audio formats (EXOTIK+DA)  
Cleaning  
Selecting a source  
Adjusting the audio  
Volume  
Connecting  
2
2
2
2
3
Unpacking  
Connecting to the mains supply  
Positioning  
Balance  
17  
Volume trim  
17  
Lip Sync Delay (EXOTIK+DA)  
Surround sound formats  
Midnight Movie mode (EXOTIK+DA)  
Restoring the original audio settings  
Record function  
18  
18  
20  
20  
21  
Back panel  
Front Panel and Handset  
Front panel display  
Front panel layout  
Handset  
4
4
4
5
Technical Specification  
Guarantee and Service  
22  
23  
Setup  
6
6
6
7
Connecting  
Setup menus  
Using the setup menus  
Speaker setup  
Source setup  
Audio setup  
7
9
11  
General setup  
UNIDISK source  
Installer Menu  
12  
14  
15  
Using the EXOTIK with a Linn UNIDISK player  
16  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Introduction  
Audio formats (EXOTIK+DA)  
Introduction  
The surround sound algorithms supplied with the EXOTIK+DA include:  
The EXOTIK pre-amplifier has been designed to provide superb audio performance with  
both two- and multi-channel source material. This product uses technology developed  
for Linn’s award-winning flagship KLIMAX Kontrol pre-amplifier and offers purist audio  
performance and access to and control of the new generation of multi-channel sound  
formats.  
Dolby Pro Logic II, Dolby Digital EX  
Two variants of the product offer different levels of functionality to suit your  
requirements:  
DTS 96/24, DTS-ES  
The standard EXOTIK is a multi-channel analogue unit supporting bass redirect, stereo  
sub algorithm and 5.1 to 2 channel downmix.  
Along with Linn’s proprietary LIMBIK algorithm.  
Note:  
A full list of the algorithms is detailed in the Surround sound formats section of the  
Operation chapter (page 18).  
EXOTIK+DA is an enhanced product which offers all the features of the standard EXOTIK  
with the addition of a digital audio module for processing of all major audio algorithms,  
including Dolby Digital 5.1, Pro Logic II, DTS Surround and DTS 96/24.*  
The EXOTIK pre-amplifier exemplifies a commitment by Linn to new products which can  
take advantage of the latest technology and audio formats whilst continuing to support  
existing Linn customers with improved performance and superb value.  
Cleaning  
Disconnect the EXOTIK from the power supply before cleaning. Remove dust and  
fingerprints with a soft, dry cloth. Avoid using domestic cleaning products on the unit.  
Important notes:  
When the unit is in standby, either EXOTIK or EXOTIK+DA is shown on the front panel  
display to indicate the product variant.  
In this manual ‘EXOTIK’ refers to both the standard and the EXOTIK+DA versions of the  
product. ‘Standard EXOTIK’ and ‘EXOTIK+DA’ refer specifically to the variants.  
*The digital audio module is available as an upgrade for the standard EXOTIK.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Connecting  
Positioning  
Connecting  
You can locate your EXOTIK anywhere you find convenient (including in a 19” rack), but  
there are a few simple points to note regarding positioning:  
This chapter explains how to install the EXOTIK pre-amplifier into your hi-fi/AV system.  
The IR sensor that receives the handset signals is quite sensitive, so the unit  
Unpacking  
The EXOTIK is supplied with the following accessories:  
should be kept out of direct sunlight to avoid false operation. The IR beam from  
the handset will pass through semi-opaque glass so operation behind, for example,  
smoked-glass cabinet doors is possible.  
luminescent handset with booklet  
Never block the ventilation slots on the top and sides of the unit.  
2 x R03 (AAA) batteries for the handset  
The unit should be protected from anything that generates significant amounts of  
1 pair of black interconnect cables  
heat, such as radiators or power amplifiers.  
RS232 lead (for connecting the EXOTIK to a Linn UNIDISK player to allow  
Note regarding Plasma and LCD screens  
communication between the two units)  
Plasma and large LCD screens emit infra-red (IR) frequencies that can interfere  
mains lead  
with the IR remote operation of the EXOTIK if the emitted IR hits the product’s  
display. Take care not to place the EXOTIK in a position where it faces the  
Plasma / LCD screen or otherwise allows the emitted IR to shine directly on to it.  
A position below or directly adjacent to the screen will normally avoid such  
interference.  
this manual  
We recommend you retain the packaging for reuse in case you need to transport the unit  
at any time.  
Connecting to the mains supply  
Manual voltage selection is not required as the EXOTIK operates from any mains AC  
power. There are no user-replaceable fuses inside the unit. The mains lead supplied may  
be fitted with a fused plug according to local regulations. If this is the case, always  
replace this fuse with another of the same type and rating.  
The EXOTIK must always be earthed when connected to the mains supply. Use  
the earthed mains lead supplied. Never use an unearthed plug or adapter with  
this unit.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Connecting  
Back panel  
1
2
POWER  
OFF  
ON  
SEE UNDERSIDE FOR SAFETY DETAILS  
1
3
MAIN  
L
OUT RS232 IN  
L
L
1
2
IN  
FRONT  
SURR  
SURR BK  
CENTRE  
SUB  
1/FRONT  
2/SURR  
3/CENTRE  
SUB  
4
5
6
1
2
3
R
R
R
5.1 GROUP  
OUT  
REMOTE  
OUTSPDIF  
TOSLINK  
OUT  
1
INPUTS  
2
3
2
4
ACC/RCU  
IR  
ANALOGUE AUDIO OUTPUTS  
TAPE OUT  
ANALOGUE AUDIO INPUTS  
*
*
13  
12  
11  
10  
9
8
7
6
5
4
3
Connector group name: Connection function  
Connector marking  
Connector  
type  
Connector group name:  
Connector marking  
Connection function  
Connector  
type  
OFF, ON  
Mains power switch  
Mains power inlet  
-
1
8
ANALOGUE AUDIO  
OUTPUTS: FRONT L-R,  
SURR L-R, SURR BK  
L-R, CENTRE, SUB  
One 7.1 analogue audio output. The SURR outputs  
are for connection to the two surround  
8 x RCA  
2
3
No name or marking  
IEC  
loudspeakers in a 5.1 system. The SURR BK outputs  
are for connection to the two additional loudspeakers  
in a 7.1 system - located at the rear of the room.  
For two-channel systems, use the FRONT outputs  
(and SUB if required) only  
*
*
TOSLINK: OUT,  
INPUTS 1 to 3  
One optical digital audio output and three inputs  
4 x TOSLINK  
SPDIF: OUT, INPUTS  
1 to 3  
One electrical digital audio output and three inputs 4 x RCA  
4
5
9
REMOTE: IN, OUT  
ACC/RCU  
RC5 in/out local loop for use in a KNEKT system  
2 x RCA  
1 x RJ45  
ANALOGUE AUDIO  
INPUTS: 4 L-R, 5 L-R,  
6 L-R  
Three stereo analogue L-R audio inputs  
6 x RCA  
6 x RCA  
10  
For installing the EXOTIK in a KNEKT  
system or for connection to an infrared repeater  
ANALOGUE AUDIO  
One 5.1 analogue audio input or three stereo  
analogue L-R audio inputs  
6
7
11  
12  
13  
1 to 4, MAIN  
IR: 1, 2  
Used if the EXOTIK is part of a KNEKT system  
Pass IR commands to auxiliary devices  
5 x RJ45  
INPUTS: 5.1 GROUP -  
1/FRONT L-R, 2/SURR  
L-R, 3/CENTRE L, SUB R  
2 x 3.5 mm jack  
2 x RJ12  
RS232: IN, OUT  
Pass control instructions to and from the EXOTIK.  
The OUT connection is used if you want to let  
the EXOTIK control another device e.g. a Linn  
UNIDISK player. The IN connection is used  
if you want to control the EXOTIK from a third-  
party home theatre controller  
TAPE OUT: L-R  
One analogue L-R output for connection to a  
recording device e.g. DAT recorder  
2 x RCA  
*EXOTIK+DA  
Switch off the EXOTIK before connecting plugs to, or disconnecting plugs from, the  
back panel to avoid generating an electrical surge that may damage the unit or other  
components of your AV system.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Front Panel and Handset  
Front Panel and Handset  
Front panel display  
The front panel display shows you information regarding what you are listening to.  
The current volume, current source, or both can be displayed along with the input audio  
signal and processing algorithm.  
The display also shows the setup menus and other information depending on the current  
operation.  
Front panel layout  
2
1
4
3
5
Front panel display  
SELECT Selects/executes options and certain commands. Used for accessing Setup Menus  
SOURCE - / +,  
Change source, for adjusting settings  
(standby) Brings unit out of, or puts into, standby mode  
1
2
3
4
5
/
VOLUME - / +,  
/
Adjust the volume level, navigate setup menus and adjust settings  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Front Panel and Handset  
Handset  
10  
11  
1
AUDIO ADJ Adjusts loudspeaker balance and trims. Resets audio settings  
LIP SYNC Adds time delay to the audio signal*  
(mute) Mutes/unmutes the audio output  
SURR Selects a surround sound format. Switches Midnight Movie mode on/off*  
VOL - / + Adjust the volume level  
2
3
4
5
6
1
2
3
4
5
6
CD Selects a CD source  
12  
13  
7
8
AUX Selects an auxiliary source  
For navigating setup menus and adjusting settings  
SETUP Enters/exits the setup menus  
(standby) Brings unit out of, or puts into, standby mode  
TV Puts handset into TV mode  
7
8
9
14  
15  
10  
11  
12  
13  
14  
TUNER Selects a tuner source  
9
DVD Selects a DVD source  
‘enter’ Selects/executes options and certain commands.  
Is used for accessing Setup Menus  
15  
(record) For setting up a record path  
16 KNEKT keys Used if the unit is installed in a KNEKT system  
Keys and functions not listed above do not function with the EXOTIK  
but may with other Linn products.  
16  
Note:  
If your EXOTIK is not responding as expected to handset keys, it is likely  
that the handset is in TV mode. To correct this press any of the source  
keys (DVD, CD, TUNER or AUX) on the handset.  
*EXOTIK+DA  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Setup  
Setup menus  
Setup  
The setup menus enable you to configure your EXOTIK for all sources it is connected to,  
the loudspeakers in your system and much more. To take advantage of your EXOTIK’s  
features, please take the time to configure your unit correctly.  
Connecting  
The first stage in setting up your EXOTIK is to connect your sources, power amp(s) and  
other peripheral devices to the EXOTIK.  
The setup menus are divided into five categories and are accessed via the MAIN MENU:  
1. Ensure your EXOTIK and all components that you will be connecting to the EXOTIK  
are disconnected from the mains supply.  
SPEAKER SETUP  
For configuring the unit for the number and size of the loudspeakers in your system and  
for calibrating their volume level. (EXOTIK+DA: also for setting the distance of your  
loudspeakers from your listening position.)  
2. Connect your source components, power amp(s) and any communication/control  
devices you wish to use, referring to the back panel diagram in the Connecting  
chapter (page 3).  
SOURCE SETUP  
For configuring sources on the unit.  
3. Connect the EXOTIK to the mains supply and turn the unit on using the switch on  
the back panel. After a few seconds the front panel will display EXOTIK or  
EXOTIK+DA depending on your unit.  
AUDIO SETUP  
For configuring the audio output of the unit.  
4. Press the  
key on the front panel or handset.  
GENERAL SETUP  
For adjusting the general setup of the unit.  
The main stage in setup is configuring the EXOTIK pre-amplifier to suit your  
requirements. This is achieved using the setup menus. How to configure the EXOTIK is  
explained in the rest of this chapter.  
UNIDISK SOURCE  
For adjusting the input settings if you are using a Linn UNIDISK player with the EXOTIK.  
There is also a UNIDISK SETUP item in the MAIN MENU for accessing the setup menus  
on a Linn UNIDISK player if one is present (see Using the EXOTIK with a Linn UNIDISK  
player, page 16).  
Using the EXOTIK with a Linn UNIDISK player  
For information on how to connect and set up your EXOTIK to a Linn UNIDISK player, see  
page 16.  
In addition, the EXOTIK features an INSTALLER MENU for saving the configuration of the  
unit as set in the above menus and restoring the factory defaults. For full information  
see Installer menu, page 15.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Setup  
Using the setup menus  
To access the setup menus:  
Either  
Speaker setup  
Press SETUP on the handset.  
SIZE  
or  
Accesses the SPEAKER SIZE sub-menu.  
Hold SELECT on the front panel until MAIN MENU / SPEAKER SETUP is shown on  
For all loudspeakers in your system (except a subwoofer) you must inform the  
EXOTIK whether the speakers are LARGE or SMALL. These settings refer to the  
frequency response of the loudspeakers, not to their physical size.  
the display.  
Standard EXOTIK  
For loudspeakers that operate below 100 Hz, select LARGE.  
For loudspeakers that do not operate below 100 Hz, select SMALL. Frequencies in  
the audio signal that are below 100 Hz will be routed to a subwoofer, if present, or  
any LARGE loudspeakers, if not.  
To access the installer menu:  
Hold SETUP on the handset or SELECT on the front panel until INSTALLER MENU  
is shown on the display (approximately 5 seconds).  
SMALL FREQUENCY (EXOTIK+DA)  
Select the operating frequency that your limited bass response (SMALL)  
loudspeakers operate above. Frequencies in the audio signal that are below the  
selected option will be routed to a subwoofer, if present, or any full-range  
loudspeakers (LARGE), if not.  
To navigate through the menus and options:  
/
Use the  
keys on the handset or front panel. Arrows on the display indicate  
which key(s) can be used.  
Options: 40 Hz, 60 Hz, 80 Hz, 100 Hz, 120 Hz  
Default setting: 80 Hz  
To make a selection:  
Press ‘enter’ on the handset, or SELECT on the front panel.  
FRONT*  
Large front speakers (full-range frequency response), set to LARGE.  
Small front speakers (limited bass response), set to SMALL.  
To exit from the setup menus:  
Press SETUP on the handset (if changes have been made you will be prompted to  
save or not save the changes).  
Default setting: LARGE  
*For two-channel systems, use the FRONT item and set CENTRE, SURROUND and  
SURROUND BACK to NONE.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Setup  
CENTRE  
DISTANCE (EXOTIK+DA)  
Accesses the SPEAKER DISTANCE sub-menu.  
Large centre speaker (full-range frequency response), set to LARGE.  
Small centre speaker (limited bass response), set to SMALL.  
No centre speaker, set to NONE.  
DISTANCE UNITS  
Select the units for loudspeaker distance measurements.  
Default setting: LARGE  
Options: FEET, METRES  
Default setting: FEET  
SURROUND  
Large surround speakers (full-range frequency response), set to LARGE.  
Small surround speakers (limited bass response), set to SMALL.  
No surround speakers, set to NONE.  
SPEAKER DISTANCE  
Default setting: LARGE  
In order to ensure that sound from all loudspeakers in your system reaches you at  
the same time, you must inform the EXOTIK+DA as to the distance each speaker is  
from your seating position. The EXOTIK+DA will then add a time delay to the  
appropriate speakers.  
SURROUND BACK  
Large surround back speakers (full-range frequency response), set to LARGE.  
Small surround back speakers (limited bass response), set to SMALL.  
No surround back speakers, set to NONE.  
Set the distance from your seating position for all speakers in your system.  
Range: 1 ft (0.3 m) to 27 ft (8.2 m)  
Default setting: 6 ft (1.8 m)  
Default setting: LARGE  
SUBWOOFER  
Select SAVE to save your changes and return to the SPEAKER SETUP menu.  
Select BACK to return to the SPEAKER SETUP menu without saving changes.  
If you have connected a subwoofer, set to YES.  
If you have not connected a subwoofer, set to NO.  
Default setting: YES  
Select EXIT to leave setup (if changes have been made and SAVE has not been  
selected, you will be prompted to save or not save the changes).  
Select SAVE to save your changes and return to the SPEAKER SETUP menu.  
Select BACK to return to the SPEAKER SETUP menu without saving changes.  
CALIBRATION  
Accesses the SPEAKER CALIBRATION sub-menu.  
Select EXIT to leave setup (if changes have been made and SAVE has not been  
selected, you will be prompted to save or not save the changes).  
SPEAKER CALIBRATION  
If your audio system uses more than two loudspeakers and a subwoofer, you can use  
the speaker calibration feature to ensure that the volume level that reaches your  
seating position is the same for each loudspeaker (speaker calibration is not  
required for two-channel systems). Calibration can be done by ear or by using an  
SPL (Sound Pressure Level) meter.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Setup  
There are differences in the method of performing loudspeaker calibration on a standard  
EXOTIK and an EXOTIK+DA:  
Range: -15 dB to 15 dB (in 0.5 steps)  
Default setting: 0 dB  
Standard EXOTIK  
Select SAVE to save your changes and return to the SPEAKER SETUP menu.  
Select BACK to return to the SPEAKER SETUP menu without saving changes.  
You will need a test disc that contains a tone signal for each loudspeaker in your system.  
Your specialist Linn retailer may be able to supply you with a suitable disc.  
To perform speaker calibration:  
Select EXIT to leave setup (if changes have been made and SAVE has not been  
selected, you will be prompted to save or not save the changes).  
Add a Linn UNIDISK player to the EXOTIK by following the setup instructions on  
page 16.  
Select BACK to return to the MAIN MENU.  
Select EXIT to leave Setup.  
Exit setup and change source to ‘UNIDISK’.  
Re-enter setup and return to the SPEAKER CALIBRATION sub-menu.  
Play the tracks on the test disc for speaker calibration while selecting the  
appropriate loudspeakers from the EXOTIK’s menu.  
Source setup  
If the tone signal coming from a particular loudspeaker is louder or quieter  
than from the other loudspeakers, use the  
trim the volume as required.  
keys on the handset to  
/
EXOTIK+DA  
Select the back panel input you wish to use with your source component.  
Please complete the source setup procedure for each source component you are  
connecting to your EXOTIK.  
To perform speaker calibration:  
Select CALIBRATION LEVEL. Adjust the calibration level so that the signal you  
hear is at a comfortable listening level (or reaches a preset level on an SPL  
meter).  
Options: ANALOG GROUP, ANALOG 1 to 6, SPDIF 1 to 3*, TOS (TOSLINK) 1 to 3*,  
KNEKT.  
Select START. The signal will move round the loudspeakers in your system in  
a clockwise direction and will be indicated on the display.  
Notes:  
If you are not using a UNIDISK player and wish to use the input(s) assigned to a UNIDISK  
player, enter the UNIDISK SOURCE menu and set ANALOG SOURCE and DIGITAL  
SOURCE* to NONE (see page 14).  
When the signal reaches a loudspeaker which is louder or quieter than the  
other loudspeakers, use the  
as required. A few seconds after the  
signal will continue its clockwise direction.  
keys on the handset to trim the volume  
/
or key has been released the  
The ANALOG GROUP uses the ANALOG 1, 2 and 3 inputs, therefore if a source is  
assigned to ANALOG GROUP you cannot also assign a source to ANALOG 1, 2 or 3.  
Conversely, if a source is assigned to ANALOG 1, 2 or 3, you cannot assign a source to  
ANALOG GROUP.  
To exit loudspeaker calibration, press SETUP on the handset or SELECT on  
the front panel.  
*EXOTIK+DA  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Setup  
NAME  
VOLUME OFFSET  
You are able to give the source a name which will be shown on the display when that  
source is selected.  
Volume offset is for adjusting the volume of a source in comparison to other  
sources. You may want to adjust the volume offset for a source if, for example, your  
tuner sounds quieter than your CD player when played at the same volume setting.  
To change the flashing character:  
Range: -15 to 15 (in 0.5 steps). No volume offset equals 0.  
Default setting: 0  
Repeatedly press or hold  
/
on the handset or front panel.  
The following characters are available: A to Z, 0 to 9, space.  
SURROUND CHANNELS  
To move to the next or previous character:  
If you are setting up the ANALOG GROUP source or are adding a Linn UNIDISK  
player and have a 7.1 speaker configuration, you are able to select whether to use  
your side surround or back surround speakers when listening to a 5.1 channel audio  
source.  
Press or  
.
When you have finished inputting the name, press ‘enter’ or SELECT.  
Default setting: (name of back panel connector or ‘UNIDISK’)  
Set to SURROUND to send the surround signal to your side surround speakers.  
Set to SURROUND BACK to send the surround signal to your back surround  
speakers.  
Notes:  
The name can be up to twelve characters long.  
Default setting: SURROUND  
The name ‘UNIDISK’ cannot be changed.  
Select SAVE to save your changes and return to the SOURCE SETUP menu.  
Select BACK to return to the SOURCE SETUP menu without saving changes.  
TYPE  
Select a type for this source. This is the type that appears on Linn learning handsets.  
Select EXIT to leave setup (if changes have been made and SAVE has not been  
selected, you will be prompted to save or not save the changes).  
Options: AUX, CD, DVD, TUNER, PHONO 1/LASER, PHONO 2/AUX, TAPE 1, TAPE  
2/VCR, DAT, TV, CABLE, SATELLITE, NONE.  
Default setting: AUX (Except ANALOG 1, 2 and 3, and KNEKT which are set to  
NONE)  
Select BACK to return to the MAIN MENU.  
Select EXIT to leave Setup.  
Notes:  
There are no options availablefor the UNIDISK input(s), as the type is assumed to be DVD.  
For ease of use with the handset supplied with the unit, you may wish to restrict the  
type selected to either CD, DVD, TUNER or AUX, to allow direct source selection.  
If you do not wish to use a particular back panel input, set Type to NONE. This means  
that when you are using the SOURCE -/+ keys on the front panel to select a source,  
inputs set to NONE will not be seen.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Setup  
MIDNIGHT MOVIE (EXOTIK+DA)  
Audio setup  
This feature allows you to add compression to the Dolby Digital audio signal on  
DVD-Videos. Adding compression reduces sudden increases in volume, such as the sound  
of an explosion.  
It is operated by pressing and holding SURR on the handset, then pressing SURR to  
toggle between on and off (see page 20).  
Options: LOW (least effective), MEDIUM, HIGH (most effective)  
Default setting: LOW  
VOLUME RATE  
Set the speed at which the EXOTIK changes volume when VOL +/VOL - is pressed.  
Range: 1/10 (slowest) to 10/10 (fastest)  
Default setting: 6/10  
DOLBY PRO LOGIC II MUSIC (EXOTIK+DA)  
Dolby Pro Logic II is an audio signal processing algorithm that converts a two-channel  
audio signal to a five-channel audio signal.  
Dolby Pro Logic II Music is a mode of Dolby Pro Logic II that is particularly suited to  
music. It features three user-adjustable parameters that are accessed from this item.  
MUTE RATE  
Set the speed at which the EXOTIK mutes or unmutes the volume when  
when changing sources.  
is pressed, or  
CENTRE WIDTH  
This parameter allows adjustment of the audio signal between the centre  
loudspeaker and front left and right loudspeakers.  
If set to 0 (no spreading) all of the audio signal for the centre channel is sent to the  
centre loudspeaker.  
Range: 1/10 (slowest) to 10/10 (fastest)  
Default setting: 6/10  
If set to 3 (neutral) a portion of the centre channel signal is also sent to the left and  
right front loudspeakers.  
If set to 7 (Full Phantom) all of the centre channel signal is split evenly between the  
front left and right loudspeakers.  
VOLUME LIMIT  
Set the maximum volume level of the EXOTIK.  
Range: 0 to 100 (in 0.5 steps)  
Default setting: 100  
Range: 0 to 7  
Default setting: 3  
PANORAMA CONTROL  
VOLUME PRESET  
If set to ON, the Panorama control extends the audio signal from the front left and  
right loudspeakers to include the surround left and right loudspeakers. This adds a  
"wraparound" effect to the sound.  
Set the volume level of the EXOTIK when it is brought out of standby.  
The setting cannot be higher than the Volume Limit setting (see above).  
Range: 0 to 100 (in 0.5 steps)  
Default setting: 40  
Options: ON, OFF  
Default setting: OFF  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Setup  
DIMENSION CONTROL  
General setup  
This parameter allows you to shift the balance between the front and rear  
loudspeakers. Positive values move the sound towards the front, negative values  
towards the rear.  
If a recording is too spacious or strong from the surround loudspeakers it can be  
shifted "forward" to get a better balance. A stereo recording can be shifted  
"backward" to make the sound more enveloping.  
DISPLAY INTENSITY  
Range: -3 (most rear) to 3 (most front)  
Default setting: 0 (neutral)  
Set the brightness of the front panel display.  
Options: LOW, MEDIUM, HIGH  
Default setting: MEDIUM  
Select SAVE to save your changes and return to the AUDIO OPTIONS menu.  
Select BACK to return to the AUDIO OPTIONS menu without saving changes.  
DISPLAY CONTENT  
Set what information you want displayed on the unit’s front panel when it is in normal  
operation.  
Select EXIT to leave setup (if changes have been made and SAVE has not been  
selected, you will be prompted to save or not save the changes).  
Options: LAST USED (source or volume), (current) SOURCE AND VOLUME, VOLUME,  
(current) SOURCE  
Select SAVE to save your changes and return to the MAIN MENU.  
Select BACK to return to the MAIN MENU without saving changes.  
Default setting: SOURCE AND VOLUME  
DISPLAY TIMEOUT  
Select EXIT to leave setup (if changes have been made and SAVE has not been selected,  
you will be prompted to save or not save the changes).  
Set the time that new volume or source information is shown for before unit returns to  
its Display Content (see above).  
Range: 1 SEC. to 10 SEC.  
Default setting: 4 SEC.  
SELECTION TIMEOUT  
When the source is changed, this item sets the time the EXOTIK takes before the new  
source is selected.  
Range: 1 SEC. to 10 SEC.  
Default setting: 4 SEC.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Setup  
SLEEP TIMEOUT  
PRODUCT IR  
Set the time elapsed before the front panel display enters sleep mode (i.e. shows three  
dots) after a key on the front panel or handset is pressed.  
Enable or disable the infrared receiver on the front of the unit.  
Options: ENABLE, DISABLE  
Default setting: ENABLE  
Options: NEVER SLEEP, IMMEDIATE, 30 SEC., 5 MINS.  
Default setting: NEVER SLEEP  
RS232 Setup  
STARTUP SOURCE  
Accesses the RS232 SETUP sub-menu.  
Set the source the unit selects when brought out of standby.  
The RS232 Setup sub-menu is for use if the EXOTIK is communicating with other RS232  
enabled products (e.g. a third-party controller).  
Options: LAST USED, NONE, (any of the source inputs)  
Default setting: LAST USED  
BAUD RATE  
STANDBY RECORD FROM  
Set the baud rate to suit the RS232 protocol being used.  
You can record from a source component to a recording device through the EXOTIK,  
even if the EXOTIK is in standby mode.  
Range: 1200 to 230400 (11 settings)  
Default setting: 9600  
Set which source configuration you want the EXOTIK to select when it is in standby.  
Options: LAST USED, NONE, (any of the source inputs), AS KNEKT*  
Default setting: LAST USED  
PARITY  
Set parity to suit the RS232 protocol being used.  
Options: EVEN, ODD  
Default setting: EVEN  
KNEKT  
If your EXOTIK is installed in a Linn KNEKT multi-room system, select the appropriate  
setting. If your EXOTIK is not installed in a KNEKT system, select NONE.  
Options: NONE, MAIN ROOM, LOCAL ROOM, INTERSEKT  
Default setting: NONE  
DATA BITS  
Set the data bits to suit the RS232 protocol being used.  
Options: 7, 8  
ACCESSORY SOCKET  
Define the use of the accessory (ACC/RCU) socket on the back panel.  
Default setting: 7  
Options: RCU* (KNEKT Room Control Unit), IR (Infrared Repeater)  
Default setting: RCU  
STOP BITS  
Set the stop bits to suit the RS232 protocol being used.  
Options: 1, 2  
Default setting: 1  
*For use with Linn KNEKT systems.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Setup  
UNIDISK source  
RS232 EVENTS  
The EXOTIK’s defaults are set to accept a UNIDISK player as a source (see Using the  
EXOTIK with a Linn UNIDISK player, page 16). Use these menus if you are using different  
back panel inputs to the default settings shown below.  
If set to ENABLE, the unit passes information regarding its internal status to an  
external device that accepts RS232 data.  
Options: ENABLE, DISABLE  
Default setting: DISABLE  
ANALOG SOURCE  
Options: ANALOG GROUP, NONE  
Default setting: ANALOG GROUP  
Select SAVE to save your changes and return to the GENERAL SETUP menu.  
Select BACK to return to the GENERAL SETUP menu without saving changes.  
DIGITAL SOURCE*  
Options: SPDIF 1, TOS (TOSLINK) 1, NONE  
Select EXIT to leave setup (if changes have been made and SAVE has not been  
selected, you will be prompted to save or not save the changes).  
Default setting: TOS 1  
Notes:  
If you wish to use an input that is not shown above, enter the Source Setup menu, select  
the input you require and set TYPE to NONE (see pages 9 and 10). When you return to  
the UNIDISK Source menu the new input will be available.  
Select SAVE to save your changes and return to the MAIN MENU.  
Select BACK to return to the MAIN MENU without saving changes.  
If you are not using a UNIDISK player and wish to use any of the inputs shown above, set  
ANALOG SOURCE and DIGITAL SOURCE* to NONE.  
Select EXIT to leave setup (if changes have been made and SAVE has not been selected,  
you will be prompted to save or not save the changes).  
Setting the item(s) to NONE also means that when you are using the SOURCE -/+ keys  
on the front panel to select a source, ‘UNIDISK’ will not be seen.  
Select SAVE to save your changes and return to the MAIN MENU.  
Select BACK to return to the MAIN MENU without saving changes.  
Select EXIT to leave setup (if changes have been made and SAVE has not been selected,  
you will be prompted to save or not save the changes).  
*EXOTIK+DA  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Setup  
Installer menu  
To access the Installer menu:  
Hold SETUP on the handset or SELECT on the front panel until INSTALLER MENU  
is shown on the display (approximately 5 seconds).  
SAVE AS INSTALLER  
After the EXOTIK has been setup you can save the settings by selecting this item. The  
saved Installer configuration can be restored at any time should the EXOTIK’s setup be  
changed (see below). Any alterations to the product’s setup that you wish to keep as a  
new Installer configuration can be stored by selecting this item, which will overwrite the  
existing Installer configuration.  
RESTORE INSTALLER  
If you have made changes to the setup of the EXOTIK that you do not wish to keep, use  
this option to restore the Installer configuration.  
RESTORE FACTORY  
Use this option to restore the default settings for all the setup menus.  
SOFTWARE REVISION  
This item informs the installer as to the version of the software installed on the EXOTIK.  
Select EXIT to leave the Installer menu (if changes have been made you will be  
prompted to save or not save the changes).  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Setup  
Note:  
Using the EXOTIK with a Linn UNIDISK player  
The above connections are the default inputs for adding a UNIDISK player to an  
EXOTIK. If you wish to use other inputs on the EXOTIK (e.g. FRONT only, or a  
SPDIF input*, make note of the inputs you have chosen and change the UNIDISK  
SOURCE menu settings when you reach point 9 below.  
There are certain operational benefits available when using the EXOTIK with a Linn  
UNIDISK player. These benefits are as follows:  
2. Connect the video outputs you wish to use from the UNIDISK player to your  
display device.  
Standard EXOTIK  
3. Connect the RS232 product-to-product lead (supplied with the EXOTIK) from the  
EXOTIK’s RS232 OUT to the UNIDISK player’s RS232 IN.  
You are able to use either your EXOTIK’s or UNIDISK player’s handset without  
there being a conflict between the two products.  
4. Connect the EXOTIK’s REMOTE OUT to the UNIDISK player’s REMOTE IN (you will  
require an RCA phono-to-phono lead).  
You are able to access your UNIDISK player’s setup menus via the UNIDISK  
Setup option in the EXOTIK’s Main Menu setup items (i.e. the UNIDISK player’s  
setup menus will appear on the display device it is connected to).  
5. Enter User Options on your UNIDISK player.  
Set –  
EXOTIK+DA  
Front Panel IR Command/Enable IR Commands to IGNORED or OFF  
RS232 Events/Enable RS232 Events to ENABLED or ON  
Baud Rate to 9600  
When a disc is loaded into the UNIDISK player and the UNIDISK is selected as the  
source on the EXOTIK+DA, the EXOTIK+DA will automatically switch to the  
required input for the loaded disc.  
(Also, for a UNIDISK SC set Knekt Mode to SOURCE.)  
6. Exit User Options.  
The EXOTIK+DA will choose an appropriate surround sound algorithm for the  
7. Enter the General Setup menu on the EXOTIK.  
8. Enter the RS232 Setup sub-menu.  
disc’s audio stream.  
You are able to use either your EXOTIK+DA’s or UNIDISK player’s handset without  
there being a conflict between the two products.  
Set –  
Baud Rate to 9600  
Parity to EVEN  
Data Bits to 7  
You are able to access your UNIDISK player’s setup menus via the UNIDISK  
Setup option in the EXOTIK+DA’s Main Menu setup items (i.e. the UNIDISK  
player’s setup menus will appear on the display device it is connected to).  
Stop Bits to 1  
RS232 Events (either setting)  
If you wish to use a Linn UNIDISK player with your EXOTIK, follow the setup instructions  
below.  
Save settings.  
9. If you are not using the default inputs for a UNIDISK player (ANALOG  
GROUP/TOS 1), enter the UNIDISK SOURCE menu on the EXOTIK and change the  
ANALOG SOURCE and DIGITAL SOURCE* setting(s) as appropriate (see page 14).  
1. Connect-  
the UNIDISK player’s FRONT A or B, SURR, CENTRE and SUB line output  
connectors to the 5.1 GROUP input on the EXOTIK (requires 6 RCA phono-to-  
phono leads)  
10. Enter the Source Setup menu. Change the source to the input(s) used for the  
UNIDISK player and adjust the VOLUME OFFSET and SURROUND CHANNELS  
settings as required.  
the TOSLINK output from the UNIDISK player to the TOSLINK 1 input on the  
EXOTIK (requires a Toslink lead)*  
*EXOTIK+DA  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Operation  
Balance  
Operation  
To change the balance for all loudspeakers (excluding a centre speaker and/or  
subwoofer):  
Standby key  
To toggle between standby mode and operation mode:  
Press AUDIO ADJ (adjust) on the handset.  
Press  
on the front panel or handset.  
BALANCE is shown on the front panel display.  
Repeatedly press or hold to shift the balance to the right, or to shift the  
balance to the left.  
Selecting a source  
To select the source you want to watch or listen to:  
Either  
Balance range is from 10 increments to the left to 10 increments to the right, with neutral  
balance being 0.  
Press the appropriate source type key (DVD, CD, TUNER or AUX) on the handset.  
(For a Linn UNIDISK player, press DVD.)  
Volume trim  
This feature is for use in systems that have more than two loudspeakers.  
Repeatedly press the source key to cycle through available sources of that type.  
When listening to multi-channel audio or watching a DVD-Video, you may want to adjust  
the volume level of your centre, surround, back surround loudspeakers or subwoofer  
without affecting any of the other loudspeakers. This is done by adjusting volume trim.  
When the desired source is shown on the front panel display, press ‘enter’, or wait  
and the EXOTIK will select the source automatically.  
or  
To change the volume trim:  
Repeatedly press the SOURCE +/- keys on the front panel. This will cycle through  
Repeatedly press AUDIO ADJ (adjust) on the handset until the desired  
all available sources.  
loudspeaker(s) is/are shown on the front panel display.  
When the desired source is shown on the front panel display, press SELECT, or  
wait and the EXOTIK will select the source automatically.  
Repeatedly press or hold  
on the front panel or handset to  
/
increase/decrease the level of volume trim.  
Volume trim range is from -10.0 to 10.0 (in 0.5 steps) with neutral trim being 0.  
Adjusting the audio  
Volume  
Note:  
The loudspeakers shown when AUDIO ADJ is repeatedly pressed is dependent on the  
number of loudspeakers in your system and the currently selected surround sound format.  
To change the volume:  
Repeatedly press or hold VOL -/ + on the front panel or handset.  
Volume range is from 0 to 100 (in 0.5 steps).  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Operation  
The available surround sound formats, and a brief description of each, is as follows:  
Surround sound format Description  
Lip Sync Delay (EXOTIK+DA)  
You may find with certain DVD-Videos that the movement of the actors’ lips and the  
sound are not synchronized. You can correct this on the EXOTIK+DA using the Lip Sync  
Delay feature.  
Dolby Digital  
A standard for storing 5.1 channels of audio signal  
on to discs such as DVD-Videos  
To adjust Lip Sync Delay:  
Dolby Digital EX  
Spreads the surround speaker portion of a Dolby  
Digital 5.1 audio signal to two back speakers -  
converting 5.1 audio to 7.1 audio  
Press LIP SYNC on the handset.  
Press  
to increase/decrease the delay of the audio signal until the picture  
/
Dolby Pro Logic II  
Converts any non-surround sound audio signal into a  
surround sound 5.0 signal  
and audio are synchronized.  
Lip Sync Delay range is from 0 to 250 milliseconds.  
Dolby Pro Logic II Music Same as Dolby Pro Logic II but is particularly suited  
to music. Features three user-adjustable parameters  
that are accessed via the setup menus  
Note:  
Lip Sync Delay can only be applied to digital sources and is not available for DTS audio  
signals.  
DTS Digital Surround  
DTS 96/24  
A standard for storing 5.1 channels of audio signal on  
to discs such as DVD-Videos  
Surround sound formats  
Same as DTS Digital Surround but offers better audio  
quality  
The EXOTIK+DA is equipped with a wide range of surround sound formats to enhance  
your audio/home cinema experience. The only surround sound format available on the  
standard EXOTIK is Stereo Sub.  
DTS ES Matrix  
Spreads the surround speaker portion of a DTS 5.1  
audio signal to two back speakers - converting 5.1  
audio to 7.1 audio  
To change the surround sound format:  
DTS ES Discrete  
A standard for storing 6.1 channels of audio signal  
on to discs such as DVD-Videos. On the EXOTIK the  
extra channel can be spread over two back speakers -  
converting 6.1 audio to 7.1 audio  
Repeatedly press SURR on the handset until the desired format is shown on the  
front panel display.  
DTS 96/24 ES Matrix  
Higher quality of DTS Digital Surround with the  
addition of the surround sound speaker portion of  
the signal being spread to two back speakers -  
converting 5.1 audio to 7.1 audio  
Phantom  
3 Stereo  
Passes the centre channel portion of a 5.1 or 7.1  
audio signal to the front left and right speakers  
Downmixes a 5.1 or 7.1 audio signal and passes it to  
the front left and right, and centre speakers only  
cont.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Operation  
The surround sound formats that are available for the different audio input and signal types,  
are:  
Surround sound format  
Stereo Sub  
Description  
Downmixes a 5.1 audio signal to a two-channel  
signal and then routes the signal to the front left and  
right speakers and subwoofer  
Analogue audio input  
5.1 speakers in system  
7.1 speakers in system  
MPEG Stereo  
A standard for storing two-channel audio in MPEG  
files  
Stereo  
2.0  
5.1  
2.0  
5.1  
Analog 5.1  
MPEG Surround  
AAC Stereo  
A standard for storing surround sound audio in  
MPEG files  
A standard for storing two-channel audio  
A standard for storing surround sound audio  
Two-channel audio input  
AAC Surround  
LIMBIK Party  
LoRo  
LtRt  
A Linn algorithm that sends essentially the same  
audio signal to all speakers in your system  
PCM  
stereo  
signal  
Analogue  
signal  
downmixed  
(Pure Stereo)  
signal  
downmixed  
signal  
Stereo  
2.0  
5.0  
2.0  
5.0  
2.0  
5.0  
5.0  
-
2.0  
5.0  
Dolby Pro Logic II  
Dolby Pro Logic II Music  
LIMBIK Party  
Stereo Sub  
5.0  
5.0  
5.0  
5.0 & 70  
2.1  
5.0 & 70  
2.1  
5.0 & 7.0  
2.1  
2.1  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Operation  
Surround sound audio input  
Midnight Movie mode (EXOTIK+DA)  
Dolby  
DTS  
-
MPEG  
AAC  
This feature allows you to add compression to the Dolby Digital audio signal on DVD-  
Videos. Adding compression reduces sudden increases in volume, such as the sound of  
an explosion.  
Stereo  
2.0  
4.1  
3.1  
2.1  
5.1  
7.1  
-
-
4.1  
3.1  
2.1  
-
-
4.1  
3.1  
2.1  
-
Phantom  
4.1  
3.1  
2.1  
-
To switch Midnight Movie mode on/off:  
3 Stereo  
Press and hold SURR on the handset until MIDNIGHT MOVIE MODE ON or OFF is  
shown on the display.  
Stereo Sub  
Press SURR to toggle between on and off.  
Dolby Digital  
Dolby Digital + Dolby Digital EX  
DTS Digital Surround  
DTS 96/24  
-
-
-
When the mode is on MIDNIGHT is shown on the front panel display. The amount of  
compression can be adjusted using the Midnight Movie item in the Audio setup menu  
(see Midnight Movie, page 11).  
5.1  
5.1  
7.1  
7.1  
7.1  
-
-
-
-
-
-
DTS ES Matrix  
DTS ES Discrete  
DTS 96/24 ES Matrix  
MPEG Stereo  
MPEG Surround  
AAC Stereo  
-
-
-
Restoring the original audio settings  
-
-
-
To reset all the above audio items to their neutral/default settings:  
-
-
-
Press and hold AUDIO ADJ on the handset until AUDIO SETTINGS RESET is  
-
2.0  
5.1  
-
-
shown on the front panel display.  
-
-
-
-
-
2.0  
5.1  
AAC Surround  
LIMBIK Party  
-
-
-
5.0 & 7.0 5.0 & 7.0 5.0 & 7.0 5.0 & 7.0  
Notes:  
The available surround sound formats are dependent on the type of audio signal being  
processed.  
When cycling through the surround sound formats, the default format for the current  
audio signal will be marked with asterisks (e.g. *Stereo*) on the front panel display.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Operation  
Notes on the sources:  
NO SOURCE: No record path will be set.  
Record function  
AS KNEKT: When a record path on the EXOTIK is being used, this setting will allow users  
of a KNEKT Line Driver system to change the source they are listening to (which also  
changes the record path). To protect a record path, select the required record option.  
Once recording has finished, reselect the AS KNEKT option.  
The record function allows you to route a source signal to a recording device such as a  
VCR or DAT recorder.  
The record functions available on your EXOTIK are dependent on whether your unit  
includes, or does not include the digital audio module (if your unit has the digital audio  
module, EXOTIK+DA is shown on the front panel display when the unit is in standby  
mode).*  
Source inputs set to NONE will not be shown.  
Additional step for an EXOTIK+DA:  
The differences in record functionality between the two variants is shown below:  
Use the  
keys to select the record mode you want to use for making the  
/
recording, then press ‘enter’.  
Standard EXOTIK  
Analogue Record Outputs  
The available record modes are:  
Analogue source  
Any analogue source can be  
routed to the analogue outputs  
Option  
Information  
LtRt 44.1 kHz  
LtRt 48 kHz  
LtRt 88.2 kHz  
LtRt 96 kHz  
Choose the option that suits your recording device’s  
operating frequency. (With these options, multi-channel  
signals are downmixed to two channels)  
EXOTIK+DA  
Analogue Record Outputs  
Any analogue source can be  
Digital Record Outputs  
No analogue source can  
LtRt As Input  
Bit Perfect  
Analog*  
Output frequency is the same as the input frequency, and  
multi-channel signals are downmixed to two channels  
Analogue source  
Digital source  
routed to the analogue outputs be routed to the digital outputs  
Output frequency is the same as the input frequency and  
there is no processing of the signal  
Only the digital source  
currently being listened to can currently being listened to  
be routed to the analogue  
outputs  
Only the digital source  
Passes audio signals to the analogue outputs  
can be routed to the  
digital outputs  
*Analog is the only record mode available on the standard EXOTIK.  
Notes:  
To set a record path:  
The source audio signal is routed to either all of the analogue and/or all of the digital  
outputs simultaneously. It is not necessary to specify which output you are using.  
Press the  
(record) key on the handset.  
The available record modes are dependent on whether the input signal is analogue or  
digital.  
Use the  
keys to select the source you want to record, then press ‘enter’.  
/
For reasons of copyright defence some audio and video discs incorporate protection  
systems that prevent them from being recorded.  
*The digital audio module is available as an upgrade to the standard EXOTIK.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Technical Specification  
Technical Specification  
Electrical  
Mains voltage  
100-230 Vac @ 50-60 Hz  
Physical  
Weight  
3.5 kg, 7 lb 10 oz  
Dimensions  
381 (W) x 368 (D) x 80 (H) mm, 15” (W) x 14” (D) x 3” (H)  
Signal Interfaces - Inputs  
Type  
Connector  
Level  
Impedance Notes  
Digital electrical 3 x RCA  
(SPDIF)*  
500 mVp-p  
75  
-
-
Digital optical*  
Unbalanced  
3 x TOSLINK  
12 x RCA  
-
-
2 Vrms  
10k Ω  
Analogue  
Signal Interfaces - Outputs  
Type  
Connector  
Level  
Impedance Notes  
Digital electrical 1 x RCA  
(SPDIF)*  
500 mVp-p  
75 Ω  
-
-
Digital optical*  
Unbalanced  
Unbalanced  
1 x TOSLINK  
-
2 Vrms  
2 Vrms  
-
8 x RCA  
2 x RCA  
330 Ω  
Surround outputs  
Record outputs  
330 Ω  
Control Interfaces  
Type  
Port Name  
Pin Connections  
RS232  
RS232  
In  
Rx = 3, Tx = 2, 0v = 5  
Rx = 5, Tx = 4, 0v = 2  
Out  
*EXOTIK+DA  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
English  
Guarantee and Service  
Linn Products Limited  
Glasgow Road  
Waterfoot  
Eaglesham  
Glasgow G76 0EQ  
Scotland, UK  
Guarantee and Service  
This product is guaranteed under the conditions that apply in the country of purchase  
and your statutory rights are not limited. In addition to any statutory rights you may  
have, Linn undertake to replace any parts that have failed due to faulty manufacture.  
To help us, please ask your Linn retailer about the Linn warranty scheme in operation in  
your country.  
Phone:  
Fax:  
+44 (0)141 307 7777  
+44 (0)141 644 4262  
In parts of Europe, the United States of America and some other markets, extended  
warranty may be available to customers who register their purchase with Linn.  
A warranty registration card is included with the product and should be stamped by your  
retailer and returned to Linn as soon as possible. Alternatively, register your warranty  
Helpline:  
Email:  
Website:  
0500 888909  
Linn Incorporated  
8787 Perimeter Park Boulevard  
Jacksonville  
FL 32216  
USA  
Warning  
Unauthorised servicing or dismantling of the product invalidates the manufacturer’s  
warranty. There are no user serviceable parts inside the product and all enquiries  
relating to product servicing should be referred to authorised retailers only.  
Phone:  
Fax:  
Helpline:  
Email:  
+1 (904) 645 5242  
+1 (904) 645 7275  
888-671-LINN  
Technical support and information  
For technical support, product queries and information, please contact either your local  
retailer or one of the Linn offices opposite.  
Website:  
Full details of your local retailer/distributor can be found on the Linn website:  
Linn Deutschland GmbH  
Hühnerposten 1d  
D-20097 Hamburg  
Germany  
Important  
Please keep a copy of the sales receipt to establish the purchase date of the  
product.  
Phone:  
Fax:  
Email:  
Website:  
+49-(0) 40-890 660-0  
+49-(0) 40-890 660-29  
Please ensure that your equipment is insured by you during any transit or  
shipment for repair.  
EXOTIK PRE-AMPLIFIER  
Owner’s Manual  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Land Pride Child Tracker 701 053a User Manual
Lindy Switch 25032 User Manual
Lowrance electronic Fish Finder LCX 20C User Manual
Makita Trimmer JS3201 User Manual
Maxtor Computer Drive STM302504OTD3E5 RK User Manual
Maxxsonics Home Theater System P1 12D2 User Manual
Melissa Hot Beverage Maker WK 222 User Manual
Melissa Vacuum Cleaner 640 041 User Manual
Memorex Karaoke Machine MKS8502 User Manual
Middleby Marshall Oven PS200 User Manual