Linksys Printer WPSM54G User Manual

USER GUIDE  
Wireless-G PrintServer  
Model: WPSM54G  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Wireless-G PrintServer  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
Product Overview  
Chapter 1  
Back Panel  
Chapter 1:  
Product Overview  
Thank you for choosing the Linksys Wireless-G PrintServer.  
The PrintServer lets you connect a USB printer directly  
to your network, so your networked computers can  
share a single printer. It is compatible with most USB  
multifunction printers, and it allows full access to printing,  
faxing, scanning, and copying functions. Like any print  
server, users on the network can print anytime. The other  
functions are treated a little differently—any user can  
request access to one of the other functions and get  
exclusive use of that function until the task is complete.  
Reset The Reset button can be used to restore  
the PrintServer’s factory default settings or  
print a test page.  
Reset to Factory Defaults  
Hold down the Reset button for ten seconds,  
and the PrintServer will be reset to its factory  
default settings.  
Front Panel  
NOTE: Resetting the PrintServer will  
delete all of your custom settings  
and replace them with the factory  
defaults. Do not reset the PrintServer  
if you want to retain your settings.  
Print a Test Page  
USB (Green/Orange) The USB LED lights up  
green when there is a printer connected to the  
USB port. It flashes green when the PrintServer  
is sending data through the USB port. The LED  
lights up orange when there is a problem with  
the printer.  
1. Make sure that both the PrintServer and  
the printer connected to the USB port are  
powered on.  
2. Press the Reset button, and hold it down for  
two seconds.  
Wireless (Green) The Wireless LED lights up  
when there is a wireless connection. It flashes  
when the PrintServer is sending or receiving  
data over the wireless network.  
3. The test page, which lists the current settings  
of the PrintServer, will be printed.  
NOTE: PostScript printers are unable  
to print this test page. If you have a  
PostScript printer on the USB port, the  
test page will not be printed.  
Ethernet (Green/Orange)  
The  
Ethernet  
LED lights up green when the PrintServer is  
connected to a device through the Ethernet  
port. It flashes green when the PrintServer is  
sending or receiving data over that port. It  
flashes orange when collisions are detected on  
the Ethernet port.  
Ethernet The Ethernet port connects the  
PrintServer to your wired network for setup.  
Power (Green/Orange) The Power LED lights  
up green when the PrintServer is ready for use.  
It flashes green when the PrintServer is booting  
up, a system self-test is running, or the firmware  
is being upgraded. The LED lights up orange  
when there is an error.  
USB The USB port connects the PrintServer to  
the USB printer.  
Power ThePowerportconnectsthePrintServer  
to the power adapter.  
Wireless-G PrintServer  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
How to Use the PrintServer  
Chapter 2  
Whenyoudouble-clicktheicon,thePrintServerInformation  
screen will appear. Refer to the following section, “About  
the Print Server Information Screen, for details.  
Chapter 2:  
How to Use the PrintServer  
After setting up the PrintServer with the Setup Wizard  
(located on the CD-ROM and explained in the Quick  
Installation), the PrintServer will be ready for use.  
When you right-click the PrintServer diagnostic icon, you  
will see a menu with four options:  
For print jobs, your computer will automatically connect  
to the printer. However, if you want to scan, fax, or access a  
memory card, then you must use the PrintServer Utility to  
tell your computer to connect to the printer. (Many printers  
have a slot for reading information from a memory card.)  
PrintServer Icon Menu  
Connect To connect your computer to the printer for  
scans, faxes, or usage of a memory card, click Connect.  
This chapter describes the PrintServer Utility used to  
control the PrintServer.  
NOTE: The computer MUST be connected to  
the printer for all scans, faxes, or usage of a  
memory card. If the Connection status field says,  
“Disconnected, then click the Connect button.  
(The computer will automatically connect to  
the printer for print jobs.)  
How to Access the PrintServer Utility  
There are two ways to access the PrintServer Utility. One  
way uses the PrintServer icon in the system tray, and the  
other way uses the program icon accessed through the  
Start menu.  
PrintServer Icon in the System Tray  
After you have installed the PrintServer, the PrintServer  
icon will appear in the system tray of your desktop.  
Info To see the Print Server Information screen, click Info.  
Refer to the following section, “About the Print Server  
Information Screen, for details.  
About To see the version number of the PrintServer  
Utility, click OK.  
PrintServer Diagnostic Icon  
The icon can show three status options:  
Icon Showing Availability Status  
The green icon indicates that the  
printer is available for use.  
About PrintServer Utlity  
Exit To close the utility, click Exit. A confirmation screen  
will appear. If you close the utility, your computer will not  
be able to use the PrintServer. To exit the utility, click Yes.  
To keep the utility running, click No.  
Icon Showing Availability Status  
Icon Showing Connected Status  
The green icon with waves indicates  
that the computer is connected to  
the printer and ready for use.  
Icon Showing Connected Status  
Exit PrintServer Utility  
Icon Showing Offline Status  
The red icon indicates that printer is  
not available. Refer to “Appendix A:  
Troubleshooting”for instructions.  
Icon Showing Offline Status  
Wireless-G PrintServer  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
How to Use the PrintServer  
Chapter 2  
Printer Information  
Program Icon Accessed through the Start Menu  
Printer Model The model number of the connected  
printer.  
The PrintServer program icons appear in the Start menu.  
To access these icons, click Start. Select Programs. Select  
Linksys PrintServer.  
Status This section shows the printer’s status information.  
When a computer is connected to the printer, the Status  
field states the name and IP address of the computer that  
is currently connected. When a computer is not connected  
to the printer, the Status field says, “On-Line.  
Also shown is the number of seconds before the current  
computer is disconnected from the printer.  
Connection status  
Start Menu > Programs >PrintServer Program Icons  
To scan, fax, or read information from a memory card, your  
computer must be connected to the printer, indicated by  
the message, “Connected. To allow another computer to  
use the printer, click the Disconnect button. To manually  
re-connect to the printer, click the Connect button.  
You will have four options available:  
PrintServer Utility To access the PrintServer Utility, click  
PrintServer Utility. Refer to the following section, “About  
the PrintServer Information Screen, for details.  
Setup Computer To run the wizard that sets up the  
PrintServer driver, click Setup Computer. Refer to the  
Quick Installation for details.  
Auto-Disconnect  
By default, the computer will be disconnected one minute  
after the print job, scan, or fax is completed. To change  
the length of time before the computer is disconnected  
from the printer, click the Change button. Select the  
appropriate length of time from the drop-down menu,  
and then click the Set button.  
Setup PrintServer To run the wizard that sets up the  
PrintServer, click Setup PrintServer. Refer to the Quick  
Installation for details.  
Uninstall TouninstallthePrintServerfromyourcomputer,  
click Uninstall.  
About the Print Server Information Screen  
The Print Server Information screen shows status  
information for the PrintServer. Use this screen to connect  
your computer to the printer for scans, faxes, or usage of  
a memory card.  
Auto-Disconnect, time  
If you want the computer to always be connected to the  
printer, such as when you have only one computer using  
the printer, select Always connect, and then click the Set  
button.  
Auto-Disconnect, Always connect  
Print Server Information  
Connected  
Disconnected  
Wireless-G PrintServer  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
How to Use the PrintServer  
Chapter 2  
Print Server Settings  
This section shows you the PrintServer’s settings, which  
were configured during the Setup Wizard.  
If you will use the PrintServer’s web-based utility, write  
down the IP address of the PrintServer. You will need it to  
access the web-based utility.  
Diagnostic  
To run the wizard that sets up the PrintServer driver, click  
the Diagnostic button. Refer to the Quick Installation for  
details.  
Close  
To exit the Print Server Information screen, click the Close  
button.  
To change the PrintServer’s advanced settings, use the  
web-based utility. For more information, refer to “Chapter  
3: Advanced Configuration.  
Wireless-G PrintServer  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Advanced Configuration  
Chapter 3  
The Setup Tab  
The first screen that appears is the Setup tab and allows  
Chapter 3:  
Advanced Configuration  
you to change the PrintServer’s general settings.  
After setting up the PrintServer with the Setup Wizard  
(located on the CD-ROM and explained in the Quick  
Installation), the PrintServer will be ready for use.  
However, if you’d like to change its advanced settings,  
use the PrintServer’s web-based utility. This chapter will  
describe each web page of the utility and each page’s key  
functions. You can access the utility via your web browser  
on a networked computer.  
These are the main tabs: Setup, Protocol, Wireless, Printer,  
Status, and Exit. Additional tabs will be available after you  
click one of the main tabs, except for the Setup and Exit  
tabs.  
Setup > Setup  
Password  
How to Access the Web-Based Utility  
Current Password To change the PrintServer’s password,  
enter the current password in the Current Password field.  
To access the web-based utility, launch the web browser  
of your computer, and enter the PrintServer’s IP address  
in the Address field. (If you do not know its IP address,  
double-click the PrintServer Utility icon. The IP address  
of the PrintServer will be displayed on the Print Server  
Information screen.) Then press the Enter key.  
New Password and Verify Password Enter the new  
password in the New Password field, and then enter the  
new password again in the Verify Password field.  
Protocols  
On the login screen, leave the User name field blank, and  
enter the password you set when you ran the SetupWizard  
(the default password is admin). Click the OK button.  
The TCP/IP protocol is enabled by default.  
Click the Save button to apply your changes, or click the  
Cancel button to cancel your changes.  
The Protocol Tab > TCP/IP  
Click the TCP/IP tab to view or change the TCP/IP values  
of the PrintServer.  
Login Screen  
Protocol > TCP/IP  
Wireless-G PrintServer  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Advanced Configuration  
Chapter 3  
IP Address  
Obtain an IP Address Automatically If your router is  
using DHCP to automatically assign IP addresses, keep the  
default, Obtain an IP Address Automatically.  
Use the Following IP Address If you need to assign  
the PrintServer a fixed IP address (also known as static IP  
address), select Use the Following IP Address, and enter  
the appropriate values in the IP Address, Subnet Mask, and  
Gateway fields.  
Make sure the IP Address and Subnet Mask are appropriate  
for your network. If you change the PrintServer’s IP address,  
make sure you that you reconnect to the PrintServer  
using that new IP address. Otherwise, you will not be  
communicating with the PrintServer.  
Protocol > SNMP  
In most cases, the Gateway IP address is the IP address  
of your router, and you should complete the Gateway  
field if you will use the PrintServer for Internet printing.  
(To find out your router’s IP address, refer to your router’s  
documentation.)  
General  
SysContact Enter the name of the contact person.  
SysLocation Enter the location of the contact person.  
Connection  
Management Stations  
Station No. Select the number of the management  
station (1-4). Click the Get Data button to display the  
information for the selected station.  
Delay before reconnection attempt Set how long,  
in seconds, you want the PrintServer to wait between  
attempts.  
Number of reconnection attempts Specify the number  
of times that the PrintServer will attempt to connect to  
the network.  
IP Address Enter the IP address of the management  
station running the SNMP program.  
Community Enter the name of the SNMP community,  
which is usually public or private.  
Click the Save button to apply your changes, or click the  
Cancel button to cancel your changes.  
Access Select the level of access for this management  
station: Not Accessible, Read-only, or Read/Write.  
The Protocol Tab > SNMP  
Use this screen to view or change the PrintServer’s SNMP  
(Simple Network Management Protocol) settings.  
Trap Receivers  
Receiver No. Select the number of the trap receiver (1-4).  
Click the Get Data button to display the information for  
the selected trap receiver.  
The PrintServer supports SNMP, which allows network  
administrators to monitor and control the PrintServer  
through the use of network management platforms, such  
as HP OpenView.  
IP Address Enter the IP address of the trap receiver that  
will be sent the trap messages or notifications.  
The appropriate MIB file must be imported into your  
SNMP management program using the Import-Compile  
command. Check your program’s documentation for  
details on this procedure. The MIB file is named Mib2p.mib  
and is provided in the MiB folder on the Setup CD-ROM.  
Community Enter the name of the SNMP community,  
which is usually public or private.  
Enable with Severity level To designate a severity level,  
select this option. From the drop-down menu, select the  
desired level of severity, with 1 being least severe.  
Click the Save button to apply your changes, or click the  
Cancel button to cancel your changes.  
Wireless-G PrintServer  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Advanced Configuration  
Chapter 3  
The Wireless Tab > Security  
The Wireless Tab > Basic  
Configure the wireless security of the PrintServer on this  
screen. The settings you set should match the settings  
of your wireless network. Wi-Fi Protected Access (WPA),  
WPA2, and two levels of Wired Equivalent Privacy (WEP)  
encryption are available.  
This screen allows you to change the PrintServer’s basic  
wireless settings.  
If you do not want to use wireless security (not  
recommended), select None from the Security Mode drop-  
down menu.  
Wireless > Basic  
Configuration  
Regulatory Domain and MAC Address The PrintServer’s  
Regulatory Domain and MAC Address are listed and  
cannot be changed.  
Wireless > Security > None  
Wireless Security  
SSID Enter the name of your wireless network. This is the  
unique name shared by all devices in a wireless network.  
The SSID is case-sensitive and should have 32 or fewer  
characters.  
Security Mode To use WPA, select WPA Personal. To use  
WPA2, which is stronger than WPA, select WPA2 Personal.  
To use WEP, select the level of WEP encryption you want to  
use, 64 Bit Keys (10 Hex chars) or 128 Bit Keys (26 Hex  
chars), which is stronger than 64-bit WEP.  
Channel No. If your network is set to ad-hoc mode, select  
your network’s channel setting. If your network is set to  
infrastructure mode, keep the default, Auto.  
Proceed to the instructions for your security method.  
Network Type The Network Type setting shows a choice  
of two wireless modes. Select Infrastructure if you want  
the PrintServer to communicate using an access point or  
wireless router. Select Ad-Hoc if you want the PrintServer  
to communicate without using an access point or wireless  
router.  
WPA2 Personal  
Click the Save button to apply your changes, or click the  
Cancel button to cancel your changes.  
Wireless > Security > WPA2-Personal > AES  
WPA Encryption Algorithm AES is the default algorithm.  
TKIP is also available.  
WPA Shared Key Enter your Shared Key, which must  
have 8-63 characters in length.  
Click the Save button to apply your changes, or click the  
Cancel button to cancel your changes.  
Wireless-G PrintServer  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Advanced Configuration  
Chapter 3  
Authentication Select  
your  
wireless  
network’s  
WPA Personal  
authentication type. The default is Open System, for  
which the sender and the recipient do NOT use a WEP  
key for authentication. Select Shared Key if you want the  
sender and recipient to use a WEP key for authentication.  
Click the Save button to apply your changes, or click the  
Cancel button to cancel your changes.  
The Printer Tab > Scan  
By default, the computer that sent the print job will be  
disconnected one minute after the print job is completed.  
Use this screen to change the length of time the computer  
is connected to the printer.  
Wireless > Security > WPA Personal > TKIP  
WPAEncryptionAlgorithm TKIPisthedefaultalgorithm.  
AES is also available.  
Click the Save button to apply your changes, or click the  
Cancel button to cancel your changes.  
WPA Shared Key Enter your Shared Key, which must  
have 8-63 characters in length.  
Auto Disconnect  
Click the Save button to apply your changes, or click the  
Cancel button to cancel your changes.  
WEP  
Printer > Scan - Auto Disconnect  
1 min after job completed To change the number of  
minutes before the computer is disconnected from the  
printer, enter the new number (1-60) in this field.  
Always connect If you want the computer to always be  
connected to the printer, select this option.  
Wireless > Security > WEP  
Click the Save button to apply your changes, or click the  
Cancel button to cancel your changes.  
Default Transmit Key Select the Default Transmit Key  
used by your wireless network. This indicates which WEP  
key your network uses for WEP encryption.  
Passphrase Enter a Passphrase and click the Generate  
Keys button to automatically generate WEP Keys 1-4. The  
Passphrase is case-sensitive and should have 16 or fewer  
alphanumeric characters. It must match your wireless  
network’s passphrase and is compatible with Linksys  
wireless products only. (Enter the WEP key manually on  
any non-Linksys wireless products.)  
Key 1 to Key 4 To enter WEP keys manually, leave the  
Passphrase field blank and enter your WEP keys. For 64-bit  
WEP encryption, each key must have 10 hexadecimal  
characters, while for 128-bit WEP encryption, the key  
must have 26 hexadecimal characters. Valid hexadecimal  
characters are “0”-“9and “A”-“F.  
Wireless-G PrintServer  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Advanced Configuration  
Chapter 3  
Options  
The Printer Tab > Internet Printing  
Print every E-Mail Select this option if you want to print  
every e-mail message.  
Internet Printing allows you to automatically print any  
e-mails that are sent to a specific e-mail account on your  
network. This is especially useful for printing information  
when you are not connected to the network. You can print  
from any location where you can access e-mail.  
Print Banner Page Enabled by default, this feature tells  
the PrintServer to print a banner page for every print job  
(the banner page describes the print job). Deselect this  
option to disable this feature.  
Mail response when printed Select this option if you  
want an e-mail sent when a print job is complete.  
Click the Save button to apply your changes, or click the  
Cancel button to cancel your changes.  
The Printer Tab > Logical Port  
Configure the settings of each Logical Printer.  
The PrintServer has three logical or virtual printer ports.  
For example, you can have three different configurations  
for your printer: Logical Printer 1 for landscape orientation,  
Logical Printer 2 for double-sided copies, and Logical  
Printer 3 for manual feed. Map Logical Printers 1, 2, and 3  
to the physical printer on the PrintServer’s USB port.  
Printer > Internet Printing  
Mail Server  
Mail Server IP Address Enter the IP address of your mail  
server. (This value must be a fixed IP address.)  
Account Name and Password Enter the Account Name  
and Account Password.  
Verify Password Enter the Account Password again.  
Check Mail every Specify how often you want the  
PrintServer to check for e-mail to be printed.  
Printer > Logical Port  
Redirect unprintable Mail to Specify an e-mail address  
to which e-mails that cannot be printed are routed;  
this is useful for both graphic-intensive e-mails and for  
troubleshooting purposes.  
Select Printer  
Logical Printer No. Select the number (1-3) of the printer  
you wish to configure. Click the Get Data button to update  
the display with the current data for the selected logical  
printer.  
Printer  
Printer Model Enter the Printer Model. You can find this  
through the Device Manager in your Windows operating  
system.  
Details  
Pre-string (Hex) Enter the printer control string (in  
hexadecimal characters) to be sent to the printer before  
each print job. This string cannot exceed 30 characters.  
Printer Port Choose the appropriate Printer Port from  
the drop-down menu: USB 1, the PrintServer’s USB port,  
or Logical Printer 1-3. The PrintServer has three logical  
or virtual printer ports. For example, you can have three  
different configurations for your printer: Logical Printer  
1 for landscape orientation, Logical Printer 2 for double-  
sided copies, and Logical Printer 3 for manual feed. Then  
configure the Logical Printers on the Logical Port tab, so  
Logical Printers 1, 2, and 3 will be mapped to the physical  
printer on the PrintServer’s USB port.  
Post String (Hex) Enter the printer control string (in  
hexadecimal characters) to be sent to the printer after  
each print job. This string cannot exceed 30 characters.  
Convert LF to CR+LF Select this option if you want LF  
(line feed) characters changed to CR+LF (carriage return  
+ line feed) characters.  
Click the Save button to apply your changes, or click the  
Cancel button to cancel your changes.  
Wireless-G PrintServer  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Advanced Configuration  
Chapter 3  
9. Click the Device tab. Click the Upgrade button. You  
The Status Tab > Device  
will be taken to the Firmware Upgrade screen.  
The Device screen displays the current settings of the  
PrintServer. No values can be changed on this screen.  
Click the Refresh button to update the information on  
this screen.  
Firmware Upgrade  
5. Enter the location of the firmware file or click the  
Browse button to find the file.  
6. Click the Start Upgrade button, and follow the on-  
Server Details  
screen instructions.  
Status > Device - Firmware Upgrade  
When you have finished upgrading the PrintServer’s  
firmware, follow these instructions:  
1. Unplug the power from the PrintServer.  
2. Disconnect the Ethernet network cable from the  
PrintServer and router.  
Status > Device - Server Details  
3. Plug in the power to the PrintServer. It should  
automatically reconnect to the wireless network.  
Upgrade A firmware upgrade can only be performed  
when the PrintServer is connected to the network using  
its Ethernet port. If you want to upgrade the PrintServer’s  
firmware, follow these instructions:  
Click the Refresh button to update the information on  
this screen.  
The Status Tab > Printer  
The Printer screen displays the current settings of the  
printer. No values can be changed on this screen. Click the  
Refresh button to update the information on this screen.  
2. Select Support and then Download. Find your  
product’s name and download the latest firmware for  
the PrintServer.  
3. Extract the firmware file on your PC.  
4. Unplug the power from the PrintServer.  
5. Connect an Ethernet network cable to the Ethernet  
port of the PrintServer. Connect the other end of the  
cable to one of the local network ports on your router.  
NOTE: To upgrade the PrintServer’s firmware, it  
must be physically connected to your router.  
5. Open the web browser of your PC.  
Status > Printer  
6. In the Address field, enter the IP address of the  
PrintServer. (If you do not know its IP address, double-  
click the PrintServer Utility icon. The IP address of  
the PrintServer will be displayed on the Print Server  
Information screen.)  
Port 1 (USB Port)  
Print Test Page Click the Print Test Page button to print  
a test page on the connected printer.  
Click the Refresh button to update the information on  
this screen.  
7. On the login screen, enter admin in the User Name  
field. Then enter the password in the Password field.  
Click the OK button.  
8. Click the Status tab.  
Wireless-G PrintServer  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Advanced Configuration  
Chapter 3  
The Status Tab > Wireless  
The Wireless screen displays status information of the  
PrintServer’s wireless connection. No values can be  
changed on this screen. Click the Refresh button to  
update the information on this screen.  
Status > Wireless  
Link Info  
The MAC address of the associated wireless router or  
access point, channel setting, and transmission rate are  
displayed here.  
Throughput  
The transmission and reception throughput, link quality,  
and signal strength are displayed here.  
Click the Refresh button to update the information on  
this screen.  
The Exit Tab  
Click the Exit tab to close the web-based utility.  
Wireless-G PrintServer  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Troubleshooting  
Appendix A  
The PrintServer’s Ethernet LED is not lit.  
Appendix A:  
Troubleshooting  
If the PrintServer is connected to the wireless network,  
then the Ethernet LED should not be lit.  
If the PrintServer is connected to the wired network, then  
disconnectandreconnecttheEthernetnetworkcablefrom  
the Ethernet port. Also make sure that the appropriate  
Ethernet or Link LED on your router or switch is lit.  
All of the LEDs on the front of the PrintServer are not lit.  
Check the power adapter and the connection to the  
electrical outlet.  
The PrintServer Utility icon is red.  
The PrintServer’s Power LED lights up orange or flashes  
continuously.  
Checktoseeifanothercomputerinthenetworkis printing.  
Only one computer at a time can use the PrintServer.  
Reset the factory defaults. Hold down the Reset button for  
ten seconds, and the PrintServer will be reset to factory  
defaults.  
If no other computers are using the PrintServer, follow  
these instructions:  
1. Check the printer cable connection to the PrintServer  
and printer.  
NOTE: Resetting the PrintServer will delete all of  
your custom settings and replace them with the  
factory defaults. Do not reset the PrintServer if  
you want to retain your settings.  
2. Unplug the power from the PrintServer.  
3. Wait five seconds, and then plug in the power. The  
PrintServer may take up to one minute to boot up.  
To start over, I need to set the PrintServer to its factory  
default settings.  
The printer connected to the PrintServer cannot print or  
prints garbage.  
Hold down the Reset button for ten seconds, and the  
PrintServer will be reset to factory defaults.  
Follow these instructions:  
Check the cable connection between the PrintServer  
and printer.  
I need to upgrade the firmware.  
Make sure the printer driver in the application program  
or Windows matches the printer.  
Follow these instructions:  
and download the latest firmware for the PrintServer.  
Make sure the printer cable is not too long, less than  
10 feet.  
2. Extract the firmware file on your PC.  
3. Unplug the power from the PrintServer.  
If there is still a printing issue, follow these steps:  
1. Double-click the PrintServer Utility icon.  
4. Connect an Ethernet network cable to the Ethernet  
port of the PrintServer. Connect the other end of the  
cable to one of the local network ports on your router.  
2. On the Print Server Information screen, click the  
Diagnostic button.  
3. Follow the on-screen instructions.  
5. Open the web browser of your PC.  
6. In the Address field, enter the IP address of the  
PrintServer. (If you do not know its IP address, right-  
click the PrintServer Utility icon, and then click Info.  
The IP address of the PrintServer will be displayed on  
the Print Server Information screen.)  
MynetworkusesDHCP(thenetworkrouterautomatically  
assigns IP addresses), and the PrintServer gets an IP  
address conflict involving the PrintServer.  
If the PrintServer is left powered on when the DHCP server,  
which is usually the network router, is powered off, the  
PrintServer will retain its IP address without informing the  
DHCP server. Follow these instructions:  
7. On the login screen, enter admin in the User Name  
field. Then enter the password in the Password field.  
Click the OK button.  
8. Click the Status tab.  
9. Click the Device tab.  
1. Unplug the power from the PrintServer.  
2. Wait five seconds, and then plug in the power. The  
PrintServer will obtain a new IP address.  
This problem may also occur if you assigned a static IP  
address within the range used by the DHCP server. If so,  
use another IP address NOT within the range used by the  
DHCP server.  
10. Click the Upgrade button, and follow the on-screen  
instructions.  
Wireless-G PrintServer  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Troubleshooting  
Appendix A  
When you have finished upgrading the PrintServer’s  
firmware, follow these instructions:  
1. Unplug the power from the PrintServer.  
2. Disconnect the Ethernet network cable from the  
PrintServer and router.  
3. Plug in the power to the PrintServer. It should  
automatically reconnect to the wireless network.  
WEB: If your questions are not addressed here,  
refer to the Linksys website, www.linksys.com  
Wireless-G PrintServer  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Appendix B  
Appendix B:  
Specifications  
Model  
WPSM54G  
Standards  
IEEE 802.3, IEEE 802.11g,  
IEEE 802.11b, USB 1.1,  
USB 2.0  
Ports  
Button  
LEDs  
Power, USB, Ethernet  
Reset  
Power, Ethernet, Wireless,  
USB  
Cabling Type  
Category 5e Ethernet  
Cable  
Number of Antennas  
Connector Type  
1
Fixed  
No  
Detachable (Y/N)  
RF Power (EIRP) in dBm  
14 dBm @ 54 Mbps,  
18 dBm @ 11 Mbps  
Antenna Gain in dBi  
3.3 dBi  
Environmental  
Dimensions  
4.84" x 1.02" x 3.70"  
(123 x 26 x 94 mm)  
Weight  
6.30 oz (180 g)  
Power  
5V, 2A  
Certifications  
Operating Temp.  
Storage Temp.  
Operating Humidity  
Storage Humidity  
FCC Class B, UL, CE  
32 to 104ºF (0 to 40ºC)  
-4 to 158ºF (-20 to 70ºC)  
10 to 85%, Noncondensing  
5 to 90%, Noncondensing  
Wireless-G PrintServer  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Warranty Information  
Appendix C  
service offerings. This limited warranty shall not apply to  
such third party software or service offerings. This limited  
warranty does not guarantee any continued availability  
of a third party’s service for which this product’s use or  
operation may require.  
Appendix C:  
Warranty Information  
Limited Warranty  
TO THE EXTENT NOT PROHIBITED BY LAW, ALL IMPLIED  
WARRANTIES AND CONDITIONS OF MERCHANTABILITY,  
SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR  
PURPOSE ARE LIMITED TO THE DURATION OF THE  
WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED  
CONDITIONS, REPRESENTATIONS AND WARRANTIES,  
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED  
WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED.  
Some jurisdictions do not allow limitations on how long  
an implied warranty lasts, so the above limitation may not  
apply to you. This limited warranty gives you specific legal  
rights, and you may also have other rights which vary by  
jurisdiction.  
Linksys warrants this Linksys hardware product against  
defects in materials and workmanship under normal  
use for the Warranty Period, which begins on the date of  
purchase by the original end-user purchaser and lasts for  
the period specified below:  
One (1) year for new product  
Ninety (90) days for refurbished product  
This limited warranty is non-transferable and extends only  
to the original end-user purchaser. Your exclusive remedy  
and Linksys’ entire liability under this limited warranty  
will be for Linksys, at its option, to (a) repair the product  
with new or refurbished parts, (b) replace the product  
with a reasonably available equivalent new or refurbished  
Linksys product, or (c) refund the purchase price of the  
product less any rebates. Any repaired or replacement  
products will be warranted for the remainder of the  
original Warranty Period or thirty (30) days, whichever is  
longer. All products and parts that are replaced become  
the property of Linksys.  
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT  
WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE  
OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,  
INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE  
THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING  
OUT OF OR RELATED TO THE USE OF OR INABILITY TO  
USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN  
IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF  
SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY  
EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT.  
The foregoing limitations will apply even if any warranty  
or remedy provided under this limited warranty fails of  
its essential purpose. Some jurisdictions do not allow  
the exclusion or limitation of incidental or consequential  
damages, so the above limitation or exclusion may not  
apply to you.  
Exclusions and Limitations  
This limited warranty does not apply if: (a) the product  
assembly seal has been removed or damaged, (b) the  
product has been altered or modified, except by Linksys, (c)  
the product damage was caused by use with non-Linksys  
products, (d) the product has not been installed, operated,  
repaired, or maintained in accordance with instructions  
supplied by Linksys, (e) the product has been subjected to  
abnormal physical or electrical stress, misuse, negligence,  
or accident, (f) the serial number on the Product has been  
altered, defaced, or removed, or (g) the product is supplied  
or licensed for beta, evaluation, testing or demonstration  
purposes for which Linksys does not charge a purchase  
price or license fee.  
Obtaining Warranty Service  
If you have a question about your product or experience a  
problem with it, please go to www.linksys.com/support  
where you will find a variety of online support tools and  
information to assist you with your product. If the product  
proves defective during the Warranty Period, contact  
Linksys Technical Support for instructions on how to  
obtain warranty service.The telephone number for Linksys  
Technical Support in your area can be found in the product  
User Guide and at www.linksys.com. Have your product  
serial number and proof of purchase on hand when calling.  
A DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED  
TO PROCESS WARRANTY CLAIMS. If you are requested to  
return your product, you will be given a Return Materials  
Authorization (RMA) number. You are responsible for  
properly packaging and shipping your product to Linksys  
at your cost and risk. You must include the RMA number  
and a copy of your dated proof of original purchase when  
returning your product. Products received without a RMA  
number and dated proof of original purchase will be  
ALL SOFTWARE PROVIDED BY LINKSYS WITH THE  
PRODUCT, WHETHER FACTORY LOADED ON THE  
PRODUCT OR CONTAINED ON MEDIA ACCOMPANYING  
THE PRODUCT, IS PROVIDED “AS ISWITHOUT WARRANTY  
OF ANY KIND. Without limiting the foregoing, Linksys does  
not warrant that the operation of the product or software  
will be uninterrupted or error free. Also, due to the  
continual development of new techniques for intruding  
upon and attacking networks, Linksys does not warrant  
that the product, software or any equipment, system or  
network on which the product or software is used will be  
free of vulnerability to intrusion or attack. The product  
may include or be bundled with third party software or  
Wireless-G PrintServer  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Warranty Information  
Appendix C  
rejected. Do not include any other items with the product  
you are returning to Linksys. Defective product covered  
by this limited warranty will be repaired or replaced and  
returned to you without charge. Customers outside of  
the United States of America and Canada are responsible  
for all shipping and handling charges, custom duties,  
VAT and other associated taxes and charges. Repairs or  
replacements not covered under this limited warranty will  
be subject to charge at Linksysthen-current rates.  
Technical Support  
This limited warranty is neither a service nor a support  
contract. Information about Linksys’ current technical  
support offerings and policies (including any fees for  
support services) can be found at:  
This limited warranty is governed by the laws of the  
jurisdiction in which the Product was purchased by you.  
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,  
CA 92623.  
Wireless-G PrintServer  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Regulatory Information  
Appendix D  
Safety Notices  
Appendix D:  
Regulatory Information  
Caution: To reduce the risk of fire, use only No.26 AWG  
or larger telecommunication line cord.  
Do not use this product near water, for example, in a  
wet basement or near a swimming pool.  
FCC Statement  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions: (1)  
Thisdevicemaynotcauseharmfulinterference, and(2)this  
device must accept any interference received, including  
interference that may cause undesired operation.  
Avoid using this product during an electrical storm.  
There may be a remote risk of electric shock from  
lightning.  
WARNING: This product contains lead, known  
to the State of California to cause cancer, and  
birth defects or other reproductive harm. Wash  
hands after handling.  
This product has been tested and complies with the  
specifications for a Class B digital device, pursuant to Part  
15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in  
a residential installation. This equipment generates,  
uses, and can radiate radio frequency energy and, if not  
installed and used according to the instructions, may  
cause harmful interference to radio communications.  
However, there is no guarantee that interference will not  
occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception,  
which is found by turning the equipment off and on, the  
user is encouraged to try to correct the interference by  
one or more of the following measures:  
Industry Canada Statement  
This Class B digital apparatus complies with Canadian  
ICES-003 and RSS210.  
Operation is subject to the following two conditions:  
1. This device may not cause interference and  
2. This device must accept any interference, including  
interference that may cause undesired operation of the  
device. This device has been designed to operate with  
an antenna having a maximum gain of 2dBi. Antenna  
havingahighergainisstrictlyprohibitedperregulations  
of Industry Canada. The required antenna impedance  
is 50 ohms.  
Reorient or relocate the receiving antenna  
Increase the separation between the equipment or  
devices  
Connect the equipment to an outlet other than the  
receiver’s  
To reduce potential radio interference to other users,  
the antenna type and its gain should be so chosen  
that the EIRP is not more than required for successful  
communication.  
Consult a dealer or an experienced radio/TV technician  
for assistance  
FCC Caution: Any changes or modifications not expressly  
approved by the party responsible for compliance could  
void the user’s authority to operate this equipment.  
Industry Canada Radiation Exposure Statement:  
This equipment complies with IC radiation exposure limits  
set forth for an uncontrolled environment. This equipment  
should be installed and operated with minimum distance  
20cm between the radiator & your body.  
FCC Radiation Exposure Statement  
This equipment complies with FCC radiation exposure  
limits set forth for an uncontrolled environment. This  
equipment should be installed and operated with  
minimum distance 20cm between the radiator and your  
body.  
This transmitter must not be co-located or operating in  
conjunction with any other antenna or transmitter.  
This transmitter must not be co-located or operating in  
conjunction with any other antenna or transmitter. IEEE  
802.11b or 802.11g operation of this product in the USA is  
firmware-limited to channels 1 through 11.  
Wireless-G PrintServer  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Regulatory Information  
Appendix D  
Avis d’Industrie Canada  
Cet appareil numérique de la classe B est conforme aux  
Avis de non-responsabilité concernant les  
appareils sans fil  
normes NMB-003 et RSS210 du Canada.  
Les performances maximales pour les réseaux sans fil  
sont tirées des spécifications de la norme IEEE 802.11.  
Les performances réelles peuvent varier, notamment  
en fonction de la capacité du réseau sans fil, du débit  
de la transmission de données, de la portée et de la  
couverture. Les performances dépendent de facteurs,  
conditions et variables multiples, en particulier de la  
distance par rapport au point d’accès, du volume du trafic  
réseau, des matériaux utilisés dans le bâtiment et du  
type de construction, du système d’exploitation et de la  
combinaison de produits sans fil utilisés, des interférences  
et de toute autre condition défavorable.  
Lutilisation de ce dispositif est autorisée seulement aux  
conditions suivantes :  
1. il ne doit pas produire de brouillage et  
2. il doit accepter tout brouillage radioélectrique reçu,  
mêmesicebrouillageestsusceptibledecompromettre  
le fonctionnement du dispositif. Le dispositif a été  
conçupourfonctionneravecuneantenneayantungain  
maximum de 2 dBi. Les règlements d’Industrie Canada  
interdisent strictement l’utilisation d’antennes dont le  
gain est supérieur à cette limite. L’impédance requise  
de l’antenne est de 50 ohms.  
Afin de réduire le risque d’interférence aux autres  
utilisateurs, le type d’antenne et son gain doivent  
être choisis de façon à ce que la puissance isotrope  
rayonnée équivalente (p.i.r.e.) ne soit pas supérieure  
au niveau requis pour obtenir une communication  
satisfaisante.  
Avis d’Industrie Canada concernant l’exposition  
aux radiofréquences :  
Ce matériel est conforme aux limites établies par IC  
en matière d’exposition aux radiofréquences dans un  
environnement non contrôlé. Ce matériel doit être installé  
et utilisé à une distance d’au moins 20 cm entre l’antenne  
et le corps de l’utilisateur.  
L’émetteur ne doit pas être placé près d’une autre antenne  
ou d’un autre émetteur, ou fonctionner avec une autre  
antenne ou un autre émetteur.  
Wireless Disclaimer  
The maximum performance for wireless is derived from  
IEEE Standard 802.11 specifications. Actual performance  
can vary, including lower wireless network capacity,  
data throughput rate, range and coverage. Performance  
depends on many factors, conditions and variables,  
including distance from the access point, volume of  
network traffic, building materials and construction,  
operating system used, mix of wireless products used,  
interference and other adverse conditions.  
Wireless-G PrintServer  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Regulatory Information  
Appendix D  
Ceština (Czech) - Informace o ochraně životního  
prostředí pro zákazníky v zemích Evropské unie  
User Information for Consumer Products  
Covered by EU Directive 2002/96/EC on  
Waste Electric and Electronic Equipment  
(WEEE)  
This document contains important information for users  
with regards to the proper disposal and recycling of  
Linksys products. Consumers are required to comply with  
this notice for all electronic products bearing the following  
symbol:  
Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené  
tímto symbolem na produktu anebo na obalu bylo likvidováno  
s netříděným komunálním odpadem. Tento symbol udává,  
že daný produkt musí být likvidován odděleně od běžného  
komunálního odpadu. Odpovídáte za likvidaci tohoto produktu  
a dalších elektrických a elektronických zařízení prostřednictvím  
určených sběrných míst stanovených vládou nebo místními  
úřady. Správná likvidace  
a
recyklace pomáhá předcházet  
potenciálním negativním dopadům na životní prostředí a lidské  
zdraví. Podrobnější informace o likvidaci starého vybavení si  
laskavě vyžádejte od místních úřadů, podniku zabývajícího se  
likvidací komunálních odpadů nebo obchodu, kde jste produkt  
zakoupili.  
Dansk (Danish) - Miljøinformation for kunder i EU  
EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol  
på produktet og/eller emballagen ikke må bortskaffes som  
usorteret kommunalt affald. Symbolet betyder, at dette produkt  
skal bortskaffes adskilt fra det almindelige husholdningsaffald.  
Det er dit ansvar at bortskaffe dette og andet elektrisk og  
elektronisk udstyr via bestemte indsamlingssteder udpeget  
af staten eller de lokale myndigheder. Korrekt bortskaffelse  
og genvinding vil hjælpe med til at undgå mulige skader for  
miljøet og menneskers sundhed. Kontakt venligst de lokale  
myndigheder, renovationstjenesten eller den butik, hvor du  
har købt produktet, angående mere detaljeret information om  
bortskaffelse af dit gamle udstyr.  
English - Environmental Information for Customers in  
the European Union  
European Directive 2002/96/EC requires that the equipment  
bearing this symbol on the product and/or its packaging must  
not be disposed of with unsorted municipal waste. The symbol  
indicates that this product should be disposed of separately  
from regular household waste streams. It is your responsibility to  
dispose of this and other electric and electronic equipment via  
designated collection facilities appointed by the government or  
local authorities. Correct disposal and recycling will help prevent  
potential negative consequences to the environment and  
human health. For more detailed information about the disposal  
of your old equipment, please contact your local authorities,  
waste disposal service, or the shop where you purchased the  
product.  
Deutsch (German) - Umweltinformation für Kunden  
innerhalb der Europäischen Union  
Die Europäische Richtlinie 2002/96/EC verlangt, dass technische  
Ausrüstung, die direkt am Gerät und/oder an derVerpackung mit  
diesem Symbol versehen ist , nicht zusammen mit unsortiertem  
Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf  
hin, dass das Produkt von regulärem Haushaltmüll getrennt  
entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses  
Gerät und andere elektrische und elektronische Geräte über  
die dafür zuständigen und von der Regierung oder örtlichen  
Behörden dazu bestimmten Sammelstellen zu entsorgen.  
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,  
potentielle negative Folgen für Umwelt und die menschliche  
Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur  
Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an  
die örtlichen Behörden oder städtischen Entsorgungsdienste  
oder an den Händler, bei dem Sie das Produkt erworben haben.  
Български (Bulgarian)  
-
Информация относно  
опазването на околната среда за потребители в  
Европейския съюз  
Европейска директива 2002/96/EC изисква уредите, носещи  
този символ върху изделието и/или опаковката му, да не  
се изхвърля т с несортирани битови отпадъци. Символът  
обозначава, че изделието трябва да се изхвърля отделно от  
сметосъбирането на обикновените битови отпадъци. Ваша  
е отговорността този и другите електрически и електронни  
уреди да се изхвърлят в предварително определени от  
държавните или общински органи специализирани пунктове  
за събиране. Правилното изхвърляне  
и
рециклиране  
ще спомогнат да се предотвратят евентуални вредни за  
околната среда и здравето на населението последствия. За  
по-подробна информация относно изхвърлянето на вашите  
стари уреди се обърнете към местните власти, службите за  
сметосъбиране или магазина, от който сте закупили уреда.  
Wireless-G PrintServer  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Regulatory Information  
Appendix D  
Eesti (Estonian)  
Euroopa Liidus asuvatele klientidele  
-
Keskkonnaalane informatsioon  
Français (French) - Informations environnementales  
pour les clients de l’Union européenne  
Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on  
La directive européenne 2002/96/CE exige que l’équipement  
sur lequel est apposé ce symbole sur le produit et/ou son  
emballage ne soit pas jeté avec les autres ordures ménagères. Ce  
symbole indique que le produit doit être éliminé dans un circuit  
distinct de celui pour les déchets des ménages. Il est de votre  
responsabilité de jeter ce matériel ainsi que tout autre matériel  
électrique ou électronique par les moyens de collecte indiqués  
par le gouvernement et les pouvoirs publics des collectivités  
territoriales. L’élimination et le recyclage en bonne et due forme  
ont pour but de lutter contre l’impact néfaste potentiel de ce  
type de produits sur l’environnement et la santé publique. Pour  
plus d’informations sur le mode d’élimination de votre ancien  
équipement, veuillez prendre contact avec les pouvoirs publics  
locaux, le service de traitement des déchets, ou l’endroit où vous  
avez acheté le produit.  
seadmeid, millel on tootel või pakendil käesolev sümbol  
,
keelatud kõrvaldada koos sorteerimata olmejäätmetega. See  
sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest  
olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva  
ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike  
ametiasutuste poolt ette nähtud kogumispunktide kaudu.  
Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida  
võimalikke negatiivseid tagajärgi keskkonnale ning inimeste  
tervisele. Vanade seadmete kõrvaldamise kohta täpsema  
informatsiooni saamiseks võtke palun ühendust kohalike  
ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te  
toote ostsite.  
Español (Spanish) - Información medioambiental para  
clientes de la Unión Europea  
Italiano (Italian) - Informazioni relative all’ambiente  
per i clienti residenti nell’Unione Europea  
La direttiva europea 2002/96/EC richiede che le apparecchiature  
La Directiva 2002/96/CE de la UE exige que los equipos que  
lleven este símbolo en el propio aparato y/o en su embalaje  
no deben eliminarse junto con otros residuos urbanos no  
seleccionados. El símbolo indica que el producto en cuestión  
debe separarse de los residuos domésticos convencionales con  
vistas a su eliminación. Es responsabilidad suya desechar este y  
cualesquiera otros aparatos eléctricos y electrónicos a través de  
los puntos de recogida que ponen a su disposición el gobierno y  
lasautoridadeslocales. Aldesecharyreciclarcorrectamenteestos  
aparatos estará contribuyendo a evitar posibles consecuencias  
negativas para el medio ambiente y la salud de las personas. Si  
desea obtener información más detallada sobre la eliminación  
segura de su aparato usado, consulte a las autoridades locales,  
al servicio de recogida y eliminación de residuos de su zona o  
pregunte en la tienda donde adquirió el producto.  
contrassegnate con questo simbolo  
sul prodotto e/o  
sull’imballaggio non siano smaltite insieme ai rifiuti urbani  
non differenziati. Il simbolo indica che questo prodotto non  
deve essere smaltito insieme ai normali rifiuti domestici. È  
responsabilità del proprietario smaltire sia questi prodotti sia  
le altre apparecchiature elettriche ed elettroniche mediante  
le specifiche strutture di raccolta indicate dal governo o dagli  
enti pubblici locali. Il corretto smaltimento ed il riciclaggio  
aiuteranno a prevenire conseguenze potenzialmente negative  
per l’ambiente e per la salute dell’essere umano. Per ricevere  
informazioni più dettagliate circa lo smaltimento delle vecchie  
apparecchiature in Vostro possesso, Vi invitiamo a contattare gli  
enti pubblici di competenza, il servizio di smaltimento rifiuti o il  
negozio nel quale avete acquistato il prodotto.  
ξλληνικά (Greek)  
-
Στοιχεία περιβαλλοντικής  
προστασίας για πελάτες εντός της Ευρωπαϊκής  
Ένωσης  
Latviešu valoda (Latvian) - Ekoloģiska informācija  
klientiem Eiropas Savienības jurisdikcijā  
ΗΚοινοτικήΟδηγία2002/96/ECαπαιτείότιοεξοπλισμόςοοποίος  
φέρει αυτό το σύμβολο στο προϊόν και/ή στη συσκευασία  
του δεν πρέπει να απορρίπτεται μαζί με τα μικτά κοινοτικά  
απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα  
πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά  
απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος  
και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των  
καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων οι  
οποίες παρέχονται από το κράτος ή τις αρμόδιες τοπικές αρχές.  
Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη  
πιθανών αρνητικών συνεπειών για το περιβάλλον και την υγεία.  
Για περισσότερες πληροφορίες σχετικά με την απόρριψη του  
παλιού σας εξοπλισμού, παρακαλώ επικοινωνήστε με τις τοπικές  
αρχές, τις υπηρεσίες απόρριψης ή το κατάστημα από το οποίο  
αγοράσατε το προϊόν.  
Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota  
zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst  
izmest nešķirotā veidā kopā ar komunālajiem atkritumiem  
(tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē  
to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar  
parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo  
un citas elektriskas un elektroniskas ierīces izmest atkritumos,  
izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko  
nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos  
un pārstrāde tiek veikta pareizi, tad mazinās iespējamais  
kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par  
novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt  
vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā,  
kur iegādājāties šo izstrādājumu.  
Wireless-G PrintServer  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Regulatory Information  
Appendix D  
Lietuvškai (Lithuanian) - Aplinkosaugos informacija,  
skirta Europos Sąjungos vartotojams  
Nederlands (Dutch) - Milieu-informatie voor klanten  
in de Europese Unie  
Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir  
kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį),  
negalima šalinti kartu su nerūšiuotomis komunalinėmis  
atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai  
nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad  
ši ir kita elektros ar elektroninė įranga būtų šalinama per tam  
tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo  
sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta  
galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos  
apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios  
institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose  
įsigijote tą gaminį.  
De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die  
is voorzien van dit symbool op het product of de verpakking,  
niet mag worden ingezameld met niet-gescheiden huishoudelijk  
afval. Dit symbool geeft aan dat het product apart moet worden  
ingezameld. U bent zelf verantwoordelijk voor de vernietiging  
vandezeenandereelektrischeenelektronischeapparatuurviade  
daarvoor door de landelijke of plaatselijke overheid aangewezen  
inzamelingskanalen. De juiste vernietiging en recycling van  
deze apparatuur voorkomt mogelijke negatieve gevolgen voor  
het milieu en de gezondheid. Voor meer informatie over het  
vernietigen van uw oude apparatuur neemt u contact op met  
de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de  
winkel waar u het product hebt aangeschaft.  
Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti  
fl-Unjoni Ewropea  
Norsk (Norwegian) - Miljøinformasjon for kunder i EU  
EU-direktiv 2002/96/EF krever at utstyr med følgende symbol  
avbildet på produktet og/eller pakningen, ikke må kastes  
sammen med usortert avfall. Symbolet indikerer at dette  
produktet skal håndteres atskilt fra ordinær avfallsinnsamling  
for husholdningsavfall. Det er ditt ansvar å kvitte deg med  
dette produktet og annet elektrisk og elektronisk avfall via egne  
innsamlingsordninger slik myndighetene eller kommunene  
bestemmer. Korrekt avfallshåndtering og gjenvinning vil  
være med på å forhindre mulige negative konsekvenser for  
miljø og helse. For nærmere informasjon om håndtering av  
det kasserte utstyret ditt, kan du ta kontakt med kommunen,  
en innsamlingsstasjon for avfall eller butikken der du kjøpte  
produktet.  
Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih is-  
simbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema  
ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika  
li dan il-prodott għandu jintrema separatament minn ma’ l-  
iskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi  
dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku  
permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew  
mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin  
jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u  
għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata  
dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja  
lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew  
il-ħanut minn fejn xtrajt il-prodott.  
Polski (Polish) - Informacja dla klientów w Unii  
Magyar (Hungarian) - Környezetvédelmi információ az  
európai uniós vásárlók számára  
Europejskiej  
środowiska  
o
przepisach dotyczących ochrony  
A 2002/96/EC számú európai uniós irányelv megkívánja, hogy  
azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán  
az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági  
hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott  
termék kidobásakor a szokványos háztartási hulladékelszállítási  
rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön  
felelõssége, hogy ezt, és más elektromos és elektronikus  
berendezéseit a kormányzati vagy a helyi hatóságok által  
kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ  
hulladékfeldolgozás segít a környezetre és az emberi egészségre  
potenciálisan ártalmas negatív hatások megelõzésében. Ha  
elavult berendezéseinek felszámolásához további részletes  
információra van szüksége, kérjük, lépjen kapcsolatba a helyi  
hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal  
üzlettel, ahol a terméket vásárolta.  
Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt  
oznaczony symbolem znajdującym się na produkcie i/lub jego  
opakowaniu nie był wyrzucany razem z innymi niesortowanymi  
odpadami komunalnymi. Symbol ten wskazuje, że produkt  
nie powinien być usuwany razem ze zwykłymi odpadami z  
gospodarstw domowych. Na Państwu spoczywa obowiązek  
wyrzucania tego  
i
innych urządzeń elektrycznych oraz  
elektronicznychwpunktachodbioruwyznaczonychprzezwładze  
krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób  
i jego recykling pomogą zapobiec potencjalnie negatywnym  
konsekwencjom dla środowiska i zdrowia ludzkiego. W celu  
uzyskania szczegółowych informacji o usuwaniu starego sprzętu,  
prosimy zwrócić się do lokalnych władz, służb oczyszczania  
miasta lub sklepu, w którym produkt został nabyty.  
Wireless-G PrintServer  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Regulatory Information  
Appendix D  
Português (Portuguese) - Informação ambiental para  
clientes da União Europeia  
Slovenčina (Slovene) - Okoljske informacije za stranke  
v Evropski uniji  
A Directiva Europeia 2002/96/CE exige que o equipamento  
que exibe este símbolo no produto e/ou na sua embalagem  
não seja eliminado junto com os resíduos municipais não  
Evropska direktiva 2002/96/EC prepoveduje odlaganje opreme,  
označene s tem simbolom – na izdelku in/ali na embalaži – med  
običajne, nerazvrščene odpadke. Ta simbol opozarja, da je treba  
izdelek odvreči ločeno od preostalih gospodinjskih odpadkov.  
Vaša odgovornost je, da to in preostalo električno in elektronsko  
opremo odnesete na posebna zbirališča, ki jih določijo  
državne ustanove ali lokalna uprava. S pravilnim odlaganjem  
in recikliranjem boste preprečili morebitne škodljive vplive na  
okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare  
opreme, se obrnite na lokalno upravo, odpad ali trgovino, kjer  
ste izdelek kupili.  
separados.  
O
símbolo indica que este produto deve ser  
eliminado separadamente dos resíduos domésticos regulares.  
É da sua responsabilidade eliminar este e qualquer outro  
equipamento eléctrico e electrónico através das instalações  
de recolha designadas pelas autoridades governamentais ou  
locais. A eliminação e reciclagem correctas ajudarão a prevenir  
as consequências negativas para o ambiente e para a saúde  
humana. Para obter informações mais detalhadas sobre a  
forma de eliminar o seu equipamento antigo, contacte as  
autoridades locais, os serviços de eliminação de resíduos ou o  
estabelecimento comercial onde adquiriu o produto.  
Suomi (Finnish) - Ympäristöä koskevia tietoja EU-  
alueen asiakkaille  
EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä  
Română (Romanian) - Informaţii de mediu pentru  
clienţii din Uniunea Europeană  
symboli  
itse tuotteessa ja/tai sen pakkauksessa, laitteistoa  
ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana.  
Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään  
tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää  
tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet  
viemällä tuote tai tuotteet viranomaisten määräämään  
keräyspisteeseen. Laitteiston oikea hävittäminen estää  
mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten  
terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta  
saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä  
myymälästä, josta ostit tuotteen.  
Directiva europeană 2002/96/CE impune ca echipamentele care  
prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să  
nu fie casate împreună cu gunoiul menajer municipal. Simbolul  
indică faptul că acest produs trebuie să fie casat separat de  
gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi  
acest produs şi alte echipamente electrice şi electronice prin  
intermediul unităţilor de colectare special desemnate de guvern  
sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta  
la prevenirea potenţialelor consecinţe negative asupra sănătăţii  
mediului şi a oamenilor. Pentru mai multe informaţii detaliate  
cu privire la casarea acestui echipament vechi, contactaţi  
autorităţile locale, serviciul de salubrizare sau magazinul de la  
care aţi achiziţionat produsul.  
Svenska (Swedish) - Miljöinformation för kunder i  
Europeiska unionen  
Det europeiska direktivet 2002/96/EC kräver att utrustning med  
denna symbol på produkten och/eller förpackningen inte får  
kastas med osorterat kommunalt avfall. Symbolen visar att denna  
produktbörkastasefterattdenavskiljtsfrånvanligthushållsavfall.  
Det faller på ditt ansvar att kasta denna och annan elektrisk och  
elektronisk utrustning på fastställda insamlingsplatser utsedda  
av regeringen eller lokala myndigheter. Korrekt kassering och  
återvinning skyddar mot eventuella negativa konsekvenser  
för miljön och personhälsa. För mer detaljerad information om  
kassering av din gamla utrustning kontaktar du dina lokala  
myndigheter, avfallshanteringen eller butiken där du köpte  
produkten.  
Slovenčina (Slovak) - Informácie o ochrane životného  
prostredia pre zákazníkov v Európskej únii  
Podľa európskej smernice 2002/96/ES zariadenie  
s
týmto  
symbolom  
na produkte a/alebo jeho balení nesmie byť  
likvidované spolu  
s
netriedeným komunálnym odpadom.  
Symbol znamená, že produkt by sa mal likvidovať oddelene  
od bežného odpadu z domácností. Je vašou povinnosťou  
likvidovať toto i ostatné elektrické a elektronické zariadenia  
prostredníctvom špecializovaných zberných zariadení určených  
vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia  
pomôže zabrániť prípadným negatívnym dopadom na životné  
prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie  
informácie o likvidácii starého zariadenia, obráťte sa, prosím, na  
miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov  
alebo obchod, v ktorom ste si produkt zakúpili.  
WEB: For additional information, please visit  
Wireless-G PrintServer  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Software License Agreement  
Appendix E  
Schedule 1 - Linksys Software License Agreement  
Appendix E: Software  
License Agreement  
THIS LICENSE AGREEMENT IS BETWEEN YOU AND  
CISCO-LINKSYS LLC OR ONE OF ITS AFFILIATES CISCO  
SYSTEMS-LINKSYS (ASIA) PTE LTD. OR CISCO-LINKSYS  
K.K. (“LINKSYS”) LICENSING THE SOFTWARE INSTEAD OF  
CISCO-LINKSYS LLC. BY DOWNLOADING OR INSTALLING  
THE SOFTWARE, OR USING THE PRODUCT CONTAINING  
THE SOFTWARE, YOU ARE CONSENTING TO BE BOUND BY  
THIS AGREEMENT. IFYOU DO NOT AGREE TO ALL OF THESE  
TERMS, THEN YOU MAY NOT DOWNLOAD, INSTALL OR USE  
THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE  
(OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER  
PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND  
UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO  
THE RETURN PROCESS AND POLICIES OF THE PARTY FROM  
WHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE.  
Software in Linksys Products  
This product from Cisco-Linksys LLC or from one of its  
affiliates Cisco Systems-Linksys (Asia) Pte Ltd. or Cisco-  
Linksys K.K. (“Linksys”) contains software (including  
firmware) originating from Linksys and its suppliers  
and may also contain software from the open source  
community. Any software originating from Linksys and its  
suppliers is licensed under the Linksys Software License  
Agreement contained at Schedule 1 below. You may also  
be prompted to review and accept that Linksys Software  
License Agreement upon installation of the software  
License. Subject to the terms and conditions of this  
Agreement, Linksys grants the original end user purchaser  
of the Linksys product containing the Software (“You”)  
a nonexclusive license to use the Software solely as  
embedded in or (where authorized in the applicable  
documentation) for communication with such product.  
This license may not be sublicensed, and is not transferable  
except to a person or entity to which you transfer  
ownership of the complete Linksys product containing  
the Software, provided you permanently transfer all rights  
under this Agreement and do not retain any full or partial  
copies of the Software, and the recipient agrees to the  
terms of this Agreement.  
Any software from the open source community is licensed  
under the specific license terms applicable to that software  
made available by Linksys at www.linksys.com/gpl or as  
provided for in Schedules 2, 3 and 4 below.  
Where such specific license terms entitle you to the source  
code of such software, that source code is upon request  
available at cost from Linksys for at least three years  
from the purchase date of this product and may also be  
available for download from www.linksys.com/gpl. For  
detailed license terms and additional information on  
open source software in Linksys products please look at  
the Linksys public web site at: www.linksys.com/gpl/ or  
Schedules 2, 3 or 4 below as applicable.  
“Software” includes, and this Agreement will apply to  
(a) the software of Linksys or its suppliers provided in or  
with the applicable Linksys product, excluding technology  
from the open source community, and (b) any upgrades,  
updates, bug fixes or modified versions (“Upgrades”) or  
backup copies of the Software supplied to You by Linksys  
or an authorized reseller, provided you already hold a  
valid license to the original software and have paid any  
applicable fee for the Upgrade.  
BY DOWNLOADING OR INSTALLING THE SOFTWARE,  
OR USING THE PRODUCT CONTAINING THE SOFTWARE,  
YOU ARE CONSENTING TO BE BOUND BY THE SOFTWARE  
LICENSE AGREEMENTS BELOW. IF YOU DO NOT AGREE TO  
ALL OF THESE TERMS, THEN YOU MAY NOT DOWNLOAD,  
INSTALL OR USE THE SOFTWARE. YOU MAY RETURN  
UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED  
AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT)  
FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINAL  
PURCHASE, SUBJECT TO THE RETURN PROCESS AND  
POLICIES OF THE PARTY FROM WHICH YOU PURCHASED  
SUCH PRODUCT OR SOFTWARE.  
Protection of Information. The Software and  
documentation contain trade secrets and/or copyrighted  
materials of Linksys or its suppliers. You will not copy  
or modify the Software or decompile, decrypt, reverse  
engineer or disassemble the Software (except to the  
extent expressly permitted by law notwithstanding this  
provision), and You will not disclose or make available  
such trade secrets or copyrighted material in any form  
to any third party. Title to and ownership of the Software  
and documentation and any portion thereof, will remain  
solely with Linksys or its suppliers.  
Software Licenses  
The software Licenses applicable to software from Linksys  
are made available at the Linksys public web site at:  
www.linksys.com. For your convenience of reference, a  
copy of the Linksys Software License Agreement and the  
main open source code licenses used by Linksys in its  
products are contained in the Schedules below.  
Collection and Processing of Information. You agree that  
Linksys and/or its affiliates may, from time to time, collect  
and process information about your Linksys product and/  
or the Software and/or your use of either in order (i) to  
enable Linksys to offer you Upgrades; (ii) to ensure that  
Wireless-G PrintServer  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Software License Agreement  
Appendix E  
your Linksys product and/or the Software is being used in  
accordancewiththetermsofthisAgreement;(iii)toprovide  
improvements to the way Linksys delivers technology to  
you and to other Linksys customers; (iv) to enable Linksys  
to comply with the terms of any agreements it has with  
any third parties regarding your Linksys product and/or  
Software and/or (v) to enable Linksys to comply with all  
applicable laws and/or regulations, or the requirements  
of any regulatory authority or government agency.  
Linksys and/ or its affiliates may collect and process  
this information provided that it does not identify you  
personally. Your use of your Linksys product and/or the  
Software constitutes this consent by you to Linksys and/  
or its affiliatescollection and use of such information and,  
for EEA customers, to the transfer of such information to a  
location outside the EEA.  
OR RELATED TO THE USE OF OR INABILITY TO USE THE  
SOFTWARE, EVEN IF LINKSYS HAS BEEN ADVISED OF  
THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL  
LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU  
FOR THE PRODUCT. The foregoing limitations will apply  
even if any warranty or remedy under this Agreement fails  
of its essential purpose. Some jurisdictions do not allow  
the exclusion or limitation of incidental or consequential  
damages, so the above limitation or exclusion may not  
apply to You.  
Export. Software, including technical data, may be subject  
to U.S. export control laws and regulations and/or export  
or import regulations in other countries. You agree to  
comply strictly with all such laws and regulations.  
U.S. Government Users. The Software and documentation  
qualify as “commercial items” as defined at 48 C.F.R. 2.101  
and 48 C.F.R. 12.212. All Government users acquire the  
Software and documentation with only those rights  
herein that apply to non-governmental customers.  
Software Upgrades etc. If the Software enables you to  
receive Upgrades, you may elect at any time to receive  
these Upgrades either automatically or manually. If you  
elect to receive Upgrades manually or you otherwise  
elect not to receive or be notified of any Upgrades, you  
may expose your Linksys product and/or the Software  
to serious security threats and/or some features within  
your Linksys product and/or Software may become  
inaccessible. There may be circumstances where we  
apply an Upgrade automatically in order to comply with  
changes in legislation, legal or regulatory requirements  
or as a result of requirements to comply with the terms  
of any agreements Linksys has with any third parties  
regarding your Linksys product and/or the Software. You  
will always be notified of any Upgrades being delivered  
to you. The terms of this license will apply to any such  
Upgrade unless the Upgrade in question is accompanied  
by a separate license, in which event the terms of that  
license will apply.  
General Terms. This Agreement will be governed by and  
construed in accordance with the laws of the State of  
California, without reference to conflict of laws principles.  
The United Nations Convention on Contracts for the  
International Sale of Goods will not apply. If any portion  
of this Agreement is found to be void or unenforceable,  
the remaining provisions will remain in full force and  
effect. This Agreement constitutes the entire agreement  
between the parties with respect to the Software and  
supersedes any conflicting or additional terms contained  
in any purchase order or elsewhere.  
END OF SCHEDULE 1  
Schedule 2  
If this Linksys product contains open source software  
licensed under Version 2 of the “GNU General Public  
License” then the license terms below in this Schedule 2  
will apply to that open source software. The license terms  
below in this Schedule 2 are from the public web site at  
Open Source Software. The GPL or other open source  
code incorporated into the Software and the open source  
licenseforsuchsourcecodeareavailableforfreedownload  
at http://www.linksys.com/gpl. If You would like a copy  
of the GPL or other open source code in this Software on a  
CD, Linksys will mail to You a CD with such code for $9.99  
plus the cost of shipping, upon request.  
GNU GENERAL PUBLIC LICENSE  
Term and Termination. You may terminate this License  
at any time by destroying all copies of the Software  
and documentation. Your rights under this License will  
terminate immediately without notice from Linksys if You  
fail to comply with any provision of this Agreement.  
Version 2, June 1991  
Copyright © 1989, 1991 Free Software Foundation, Inc.  
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,  
USA  
Limited Warranty. The warranty terms and period  
specified in the applicable Linksys Product User Guide  
shall also apply to the Software.  
Everyone is permitted to copy and distribute verbatim  
copies of this license document, but changing it is not  
allowed.  
Disclaimer of Liabilities. IN NO EVENT WILL LINKSYS OR  
ITS SUPPLIERS BE LIABLE FOR ANY LOST DATA, REVENUE  
OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,  
INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF  
CAUSE (INCLUDING NEGLIGENCE), ARISING OUT OF  
Preamble  
The licenses for most software are designed to take away  
your freedom to share and change it. By contrast, the  
Wireless-G PrintServer  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Software License Agreement  
Appendix E  
GNU General Public License is intended to guarantee your  
freedom to share and change free software–to make sure  
the software is free for all its users. This General Public  
License applies to most of the Free Software Foundation’s  
software and to any other program whose authors  
commit to using it. (Some other Free Software Foundation  
software is covered by the GNU Lesser General Public  
License instead.) You can apply it to your programs, too.  
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND  
MODIFICATION  
0. This License applies to any program or other work  
which contains a notice placed by the copyright  
holder saying it may be distributed under the terms  
of this General Public License. The “Program, below,  
refers to any such program or work, and a “work  
based on the Program” means either the Program  
or any derivative work under copyright law: that is  
to say, a work containing the Program or a portion  
of it, either verbatim or with modifications and/  
or translated into another language. (Hereinafter,  
translation is included without limitation in the term  
“modification.) Each licensee is addressed as “you.  
When we speak of free software, we are referring to  
freedom, not price. Our General Public Licenses are  
designed to make sure that you have the freedom to  
distribute copies of free software (and charge for this  
service if you wish), that you receive source code or can  
get it if you want it, that you can change the software or  
use pieces of it in new free programs; and that you know  
you can do these things.  
Activities other than copying, distribution and  
modification are not covered by this License; they  
are outside its scope. The act of running the Program  
is not restricted, and the output from the Program is  
covered only if its contents constitute a work based on  
the Program (independent of having been made by  
running the Program). Whether that is true depends  
on what the Program does.  
To protect your rights, we need to make restrictions that  
forbid anyone to deny you these rights or to ask you to  
surrender the rights. These restrictions translate to certain  
responsibilities for you if you distribute copies of the  
software, or if you modify it.  
For example, if you distribute copies of such a program,  
whether gratis or for a fee, you must give the recipients  
all the rights that you have. You must make sure that they,  
too, receive or can get the source code. And you must  
show them these terms so they know their rights.  
1. You may copy and distribute verbatim copies of the  
Program’s source code as you receive it, in any medium,  
provided that you conspicuously and appropriately  
publish on each copy an appropriate copyright  
notice and disclaimer of warranty; keep intact all the  
notices that refer to this License and to the absence  
of any warranty; and give any other recipients of the  
Program a copy of this License along with the Program.  
We protect your rights with two steps: (1) copyright the  
software, and (2) offer you this license which gives you  
legal permission to copy, distribute and/or modify the  
software.  
Also, for each author’s protection and ours, we want to  
make certain that everyone understands that there is no  
warranty for this free software. If the software is modified  
by someone else and passed on, we want its recipients  
to know that what they have is not the original, so that  
any problems introduced by others will not reflect on the  
original authorsreputations.  
You may charge a fee for the physical act of transferring  
a copy, and you may at your option offer warranty  
protection in exchange for a fee.  
2. You may modify your copy or copies of the Program  
or any portion of it, thus forming a work based on the  
Program, and copy and distribute such modifications  
or work under the terms of Section 1 above, provided  
that you also meet all of these conditions:  
Finally, any free program is threatened constantly by  
software patents. We wish to avoid the danger that  
redistributors of a free program will individually obtain  
patent licenses, in effect making the program proprietary.  
To prevent this, we have made it clear that any patent must  
be licensed for everyone’s free use or not licensed at all.  
a. You must cause the modified files to carry  
prominent notices stating that you changed the  
files and the date of any change.  
b. You must cause any work that you distribute or  
publish, that in whole or in part contains or is  
derived from the Program or any part thereof, to be  
licensed as a whole at no charge to all third parties  
under the terms of this License.  
The precise terms and conditions for copying, distribution  
and modification follow.  
Wireless-G PrintServer  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Software License Agreement  
Appendix E  
c. If the modified program normally reads commands  
c. Accompany it with the information you received as  
totheoffertodistributecorrespondingsourcecode.  
(This alternative is allowed only for noncommercial  
distribution and only if you received the program  
in object code or executable form with such an  
offer, in accord with Subsection b above.)  
interactively when run, you must cause it, when  
started running for such interactive use in the most  
ordinary way, to print or display an announcement  
including an appropriate copyright notice and  
a notice that there is no warranty (or else, saying  
that you provide a warranty) and that users may  
redistribute the program under these conditions,  
and telling the user how to view a copy of  
this License. (Exception: if the Program itself is  
interactive but does not normally print such an  
announcement, your work based on the Program  
is not required to print an announcement.)  
The source code for a work means the preferred form  
of the work for making modifications to it. For an  
executable work, complete source code means all  
the source code for all modules it contains, plus any  
associated interface definition files, plus the scripts  
used to control compilation and installation of the  
executable. However, as a special exception, the source  
code distributed need not include anything that is  
normally distributed (in either source or binary form)  
with the major components (compiler, kernel, and so  
on) of the operating system on which the executable  
runs, unless that component itself accompanies the  
executable.  
These requirements apply to the modified work as  
a whole. If identifiable sections of that work are not  
derived from the Program, and can be reasonably  
considered independent and separate works in  
themselves, then this License, and its terms, do not  
apply to those sections when you distribute them as  
separate works. But when you distribute the same  
sections as part of a whole which is a work based on  
the Program, the distribution of the whole must be on  
the terms of this License, whose permissions for other  
licensees extend to the entire whole, and thus to each  
and every part regardless of who wrote it.  
If distribution of executable or object code is made  
by offering access to copy from a designated place,  
then offering equivalent access to copy the source  
code from the same place counts as distribution of  
the source code, even though third parties are not  
compelled to copy the source along with the object  
code.  
Thus, it is not the intent of this section to claim rights  
or contest your rights to work written entirely by you;  
rather, the intent is to exercise the right to control the  
distribution of derivative or collective works based on  
the Program.  
4. You may not copy, modify, sublicense, or distribute  
the Program except as expressly provided under  
this License. Any attempt otherwise to copy, modify,  
sublicense or distribute the Program is void, and will  
automatically terminate your rights under this License.  
However, parties who have received copies, or rights,  
from you under this License will not have their licenses  
terminated so long as such parties remain in full  
compliance.  
In addition, mere aggregation of another work not  
based on the Program with the Program (or with a  
work based on the Program) on a volume of a storage  
or distribution medium does not bring the other work  
under the scope of this License.  
5. You are not required to accept this License, since you  
have not signed it. However, nothing else grants you  
permission to modify or distribute the Program or its  
derivative works. These actions are prohibited by law if  
you do not accept this License.Therefore, by modifying  
or distributing the Program (or any work based on the  
Program), you indicate your acceptance of this License  
to do so, and all its terms and conditions for copying,  
distributing or modifying the Program or works based  
on it.  
3. You may copy and distribute the Program (or a  
work based on it, under Section 2) in object code or  
executable form under the terms of Sections 1 and 2  
above provided that you also do one of the following:  
a. Accompany it with the complete corresponding  
machine-readable source code, which must be  
distributed under the terms of Sections 1 and 2  
above on a medium customarily used for software  
interchange; or,  
b. Accompany it with a written offer, valid for at least  
three years, to give any third party, for a charge  
no more than your cost of physically performing  
source distribution, a complete machine-readable  
copy of the corresponding source code, to be  
distributed under the terms of Sections 1 and 2  
above on a medium customarily used for software  
interchange; or,  
6. Each time you redistribute the Program (or any work  
based on the Program), the recipient automatically  
receives a license from the original licensor to copy,  
distribute or modify the Program subject to these  
terms and conditions. You may not impose any further  
restrictions on the recipients’ exercise of the rights  
granted herein. You are not responsible for enforcing  
compliance by third parties to this License.  
Wireless-G PrintServer  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Software License Agreement  
Appendix E  
7. If, as a consequence of a court judgment or allegation  
of patent infringement or for any other reason (not  
limited to patent issues), conditions are imposed on  
you (whether by court order, agreement or otherwise)  
that contradict the conditions of this License, they do  
not excuse you from the conditions of this License. If  
you cannot distribute so as to satisfy simultaneously  
your obligations under this License and any other  
pertinent obligations, then as a consequence you  
may not distribute the Program at all. For example,  
if a patent license would not permit royalty-free  
redistribution of the Program by all those who receive  
copies directly or indirectly through you, then the only  
way you could satisfy both it and this License would be  
to refrain entirely from distribution of the Program.  
not specify a version number of this License, you  
may choose any version ever published by the Free  
Software Foundation.  
10. If you wish to incorporate parts of the Program into  
other free programs whose distribution conditions are  
different, write to the author to ask for permission. For  
software which is copyrighted by the Free Software  
Foundation, write to the Free Software Foundation; we  
sometimes make exceptions for this. Our decision will  
be guided by the two goals of preserving the free status  
of all derivatives of our free software and of promoting  
the sharing and reuse of software generally.  
NO WARRANTY  
11. BECAUSETHEPROGRAMISLICENSEDFREEOFCHARGE,  
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE  
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT  
WHENOTHERWISESTATEDINWRITINGTHECOPYRIGHT  
HOLDERS AND/OR OTHER PARTIES PROVIDE THE  
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY  
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,  
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND  
PERFORMANCE OF THE PROGRAM IS WITH YOU.  
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU  
ASSUME THE COST OF ALL NECESSARY SERVICING,  
REPAIR OR CORRECTION.  
If any portion of this section is held invalid or  
unenforceable under any particular circumstance,  
the balance of the section is intended to apply and  
the section as a whole is intended to apply in other  
circumstances.  
It is not the purpose of this section to induce you to  
infringe any patents or other property right claims or  
to contest validity of any such claims; this section has  
the sole purpose of protecting the integrity of the free  
software distribution system, which is implemented  
by public license practices. Many people have  
made generous contributions to the wide range of  
software distributed through that system in reliance  
on consistent application of that system; it is up to  
the author/donor to decide if he or she is willing to  
distribute software through any other system and a  
licensee cannot impose that choice.  
12. INNOEVENTUNLESSREQUIREDBYAPPLICABLELAWOR  
AGREEDTO INWRITINGWILL ANY COPYRIGHT HOLDER,  
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR  
REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE,  
BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY  
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL  
DAMAGES ARISING OUT OF THE USE OR INABILITY TO  
USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO  
LOSS OF DATA OR DATA BEING RENDERED INACCURATE  
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR  
A FAILURE OF THE PROGRAM TO OPERATE WITH ANY  
OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER  
PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF  
SUCH DAMAGES.  
This section is intended to make thoroughly clear  
what is believed to be a consequence of the rest of this  
License.  
8. If the distribution and/or use of the Program is  
restricted in certain countries either by patents or by  
copyrighted interfaces, the original copyright holder  
who places the Program under this License may add an  
explicit geographical distribution limitation excluding  
those countries, so that distribution is permitted only  
in or among countries not thus excluded. In such case,  
this License incorporates the limitation as if written in  
the body of this License.  
END OF TERMS AND CONDITIONS  
END OF SCHEDULE 2  
9. The Free Software Foundation may publish revised  
and/or new versions of the General Public License  
from time to time. Such new versions will be similar in  
spirit to the present version, but may differ in detail to  
address new problems or concerns.  
Schedule 3  
If this Linksys product contains open source software  
licensedunderVersion2.1ofthe“GNULesserGeneralPublic  
License” then the license terms below in this Schedule 3  
will apply to that open source software. The license terms  
below in this Schedule 3 are from the public web site at  
Each version is given a distinguishing version number.  
If the Program specifies a version number of this  
License which applies to it and “any later version, you  
have the option of following the terms and conditions  
either of that version or of any later version published  
by the Free Software Foundation. If the Program does  
.
Wireless-G PrintServer  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Software License Agreement  
Appendix E  
To protect each distributor, we want to make it very clear  
that there is no warranty for the free library. Also, if the  
library is modified by someone else and passed on, the  
recipients should know that what they have is not the  
original version, so that the original author’s reputation  
will not be affected by problems that might be introduced  
by others.  
GNU LESSER GENERAL PUBLIC LICENSE  
Version 2.1, February 1999  
Copyright (C) 1991, 1999 Free Software Foundation, Inc.  
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,  
USA  
Everyone is permitted to copy and distribute verbatim  
copies of this license document, but changing it is not  
allowed.  
Finally, software patents pose a constant threat to the  
existence of any free program. We wish to make sure  
that a company cannot effectively restrict the users of  
a free program by obtaining a restrictive license from a  
patent holder. Therefore, we insist that any patent license  
obtained for a version of the library must be consistent  
with the full freedom of use specified in this license.  
[This is the first released version of the Lesser GPL. It also  
counts as the successor of the GNU Library Public License,  
version 2, hence the version number 2.1.]  
Preamble  
Most GNU software, including some libraries, is covered  
by the ordinary GNU General Public License. This license,  
the GNU Lesser General Public License, applies to certain  
designated libraries, and is quite different from the  
ordinary General Public License. We use this license for  
certain libraries in order to permit linking those libraries  
into non-free programs.  
The licenses for most software are designed to take away  
your freedom to share and change it. By contrast, the GNU  
General Public Licenses are intended to guarantee your  
freedom to share and change free software—to make  
sure the software is free for all its users.  
This license, the Lesser General Public License, applies to  
some specially designated software packages—typically  
libraries—of the Free Software Foundation and other  
authors who decide to use it. You can use it too, but we  
suggest you first think carefully about whether this license  
or the ordinary General Public License is the better strategy  
to use in any particular case, based on the explanations  
below.  
When a program is linked with a library, whether  
statically or using a shared library, the combination of  
the two is legally speaking a combined work, a derivative  
of the original library. The ordinary General Public  
License therefore permits such linking only if the entire  
combination fits its criteria of freedom. The Lesser General  
Public License permits more lax criteria for linking other  
code with the library.  
When we speak of free software, we are referring to  
freedom of use, not price. Our General Public Licenses  
are designed to make sure that you have the freedom  
to distribute copies of free software (and charge for this  
service if you wish); that you receive source code or can  
get it if you want it; that you can change the software and  
use pieces of it in new free programs; and that you are  
informed that you can do these things.  
We call this license the “Lesser” General Public License  
because it does Less to protect the user’s freedom than  
the ordinary General Public License. It also provides  
other free software developers Less of an advantage over  
competing non-free programs. These disadvantages are  
the reason we use the ordinary General Public License  
for many libraries. However, the Lesser license provides  
advantages in certain special circumstances.  
To protect your rights, we need to make restrictions that  
forbid distributors to deny you these rights or to ask you  
to surrender these rights. These restrictions translate to  
certain responsibilities for you if you distribute copies of  
the library or if you modify it.  
For example, on rare occasions, there may be a special  
need to encourage the widest possible use of a certain  
library, so that it becomes a de-facto standard. To achieve  
this, non-free programs must be allowed to use the library.  
A more frequent case is that a free library does the same  
job as widely used non-free libraries. In this case, there is  
little to gain by limiting the free library to free software  
only, so we use the Lesser General Public License.  
For example, if you distribute copies of the library,  
whether gratis or for a fee, you must give the recipients  
all the rights that we gave you. You must make sure that  
they, too, receive or can get the source code. If you link  
other code with the library, you must provide complete  
object files to the recipients, so that they can relink them  
with the library after making changes to the library and  
recompiling it. And you must show them these terms so  
they know their rights.  
In other cases, permission to use a particular library in non-  
free programs enables a greater number of people to use  
a large body of free software. For example, permission to  
use the GNU C Library in non-free programs enables many  
more people to use the whole GNU operating system, as  
well as its variant, the GNU/Linux operating system.  
We protect your rights with a two-step method: (1) we  
copyright the library, and (2) we offer you this license,  
which gives you legal permission to copy, distribute and/  
or modify the library.  
Although the Lesser General Public License is Less  
protective of the users’ freedom, it does ensure that the  
user of a program that is linked with the Library has the  
Wireless-G PrintServer  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Software License Agreement  
Appendix E  
freedom and the wherewithal to run that program using a  
modified version of the Library.  
1. You may copy and distribute verbatim copies of the  
Library’s complete source code as you receive it, in  
any medium, provided that you conspicuously and  
appropriately publish on each copy an appropriate  
copyright notice and disclaimer of warranty; keep  
intact all the notices that refer to this License and to  
the absence of any warranty; and distribute a copy of  
this License along with the Library.  
The precise terms and conditions for copying, distribution  
and modification follow. Pay close attention to the  
difference between a “work based on the library” and a  
“work that uses the library. The former contains code  
derived from the library, whereas the latter must be  
combined with the library in order to run.  
You may charge a fee for the physical act of transferring  
a copy, and you may at your option offer warranty  
protection in exchange for a fee.  
GNU LESSER GENERAL PUBLIC LICENSE  
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND  
MODIFICATION  
2. You may modify your copy or copies of the Library or  
any portion of it, thus forming a work based on the  
Library, and copy and distribute such modifications  
or work under the terms of Section 1 above, provided  
that you also meet all of these conditions:  
0. This License Agreement applies to any software library  
or other program which contains a notice placed by  
the copyright holder or other authorized party saying  
it may be distributed under the terms of this Lesser  
General Public License (also calledthis License”). Each  
licensee is addressed as “you.  
a) The modified work must itself be a software  
library.  
b) You must cause the files modified to carry  
prominent notices stating that you changed the  
files and the date of any change.  
A “library” means a collection of software functions  
and/or data prepared so as to be conveniently linked  
with application programs (which use some of those  
functions and data) to form executables.  
c) You must cause the whole of the work to be  
licensed at no charge to all third parties under the  
terms of this License.  
TheLibrary, below, refers to any such software library  
or work which has been distributed under these terms.  
Awork based on the Librarymeans either the Library  
or any derivative work under copyright law: that is to  
say, a work containing the Library or a portion of it,  
either verbatim or with modifications and/or translated  
straightforwardly into another language. (Hereinafter,  
translation is included without limitation in the term  
“modification.)  
d) IfafacilityinthemodifiedLibraryreferstoafunction  
or a table of data to be supplied by an application  
program that uses the facility, other than as an  
argument passed when the facility is invoked, then  
you must make a good faith effort to ensure that,  
in the event an application does not supply such  
function or table, the facility still operates, and  
performs whatever part of its purpose remains  
meaningful.  
“Source code” for a work means the preferred form of  
the work for making modifications to it. For a library,  
complete source code means all the source code for  
all modules it contains, plus any associated interface  
definition files, plus the scripts used to control  
compilation and installation of the library.  
(For example, a function in a library to compute  
square roots has a purpose that is entirely well-  
defined independent of the application. Therefore,  
Subsection 2d requires that any application-  
supplied function or table used by this function  
must be optional: if the application does not supply  
it, the square root function must still compute  
square roots.)  
Activities other than copying, distribution and  
modification are not covered by this License; they are  
outside its scope. The act of running a program using  
the Library is not restricted, and output from such a  
program is covered only if its contents constitute a  
work based on the Library (independent of the use  
of the Library in a tool for writing it). Whether that is  
true depends on what the Library does and what the  
program that uses the Library does.  
These requirements apply to the modified work as  
a whole. If identifiable sections of that work are not  
derived from the Library, and can be reasonably  
considered independent and separate works in  
themselves, then this License, and its terms, do  
not apply to those sections when you distribute  
them as separate works. But when you distribute  
the same sections as part of a whole which is a  
work based on the Library, the distribution of the  
whole must be on the terms of this License, whose  
permissions for other licensees extend to the entire  
whole, and thus to each and every part regardless  
of who wrote it.  
Wireless-G PrintServer  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Software License Agreement  
Appendix E  
Thus, it is not the intent of this section to claim  
When awork that uses the Libraryuses material from  
a header file that is part of the Library, the object code  
for the work may be a derivative work of the Library  
even though the source code is not. Whether this is  
true is especially significant if the work can be linked  
without the Library, or if the work is itself a library. The  
threshold for this to be true is not precisely defined by  
law.  
rights or contest your rights to work written entirely  
by you; rather, the intent is to exercise the right to  
control the distribution of derivative or collective  
works based on the Library.  
In addition, mere aggregation of another work  
not based on the Library with the Library (or with  
a work based on the Library) on a volume of a  
storage or distribution medium does not bring the  
other work under the scope of this License.  
If such an object file uses only numerical parameters,  
data structure layouts and accessors, and small macros  
and small inline functions (ten lines or less in length),  
then the use of the object file is unrestricted, regardless  
of whether it is legally a derivative work. (Executables  
containing this object code plus portions of the Library  
will still fall under Section 6.)  
3. You may opt to apply the terms of the ordinary GNU  
General Public License instead of this License to a  
given copy of the Library. To do this, you must alter all  
the notices that refer to this License, so that they refer  
to the ordinary GNU General Public License, version  
2, instead of to this License. (If a newer version than  
version 2 of the ordinary GNU General Public License  
has appeared, then you can specify that version  
instead if you wish.) Do not make any other change in  
these notices.  
Otherwise, if the work is a derivative of the Library, you  
may distribute the object code for the work under the  
terms of Section 6. Any executables containing that  
work also fall under Section 6, whether or not they are  
linked directly with the Library itself.  
Once this change is made in a given copy, it is  
irreversible for that copy, so the ordinary GNU General  
Public License applies to all subsequent copies and  
derivative works made from that copy.  
6. As an exception to the Sections above, you may also  
combine or link a “work that uses the Library” with the  
Library to produce a work containing portions of the  
Library, and distribute that work under terms of your  
choice, provided that the terms permit modification  
of the work for the customer’s own use and reverse  
engineering for debugging such modifications.  
This option is useful when you wish to copy part of the  
code of the Library into a program that is not a library.  
4. You may copy and distribute the Library (or a portion  
or derivative of it, under Section 2) in object code or  
executable form under the terms of Sections 1 and  
2 above provided that you accompany it with the  
complete corresponding machine-readable source  
code, which must be distributed under the terms of  
Sections 1 and 2 above on a medium customarily used  
for software interchange.  
You must give prominent notice with each copy of  
the work that the Library is used in it and that the  
Library and its use are covered by this License. You  
must supply a copy of this License. If the work during  
execution displays copyright notices, you must include  
the copyright notice for the Library among them, as  
well as a reference directing the user to the copy of this  
License. Also, you must do one of these things:  
If distribution of object code is made by offering  
access to copy from a designated place, then offering  
equivalent access to copy the source code from the  
same place satisfies the requirement to distribute  
the source code, even though third parties are not  
compelled to copy the source along with the object  
code.  
a) Accompany the work with the complete  
corresponding machine-readable source code  
for the Library including whatever changes were  
used in the work (which must be distributed  
under Sections 1 and 2 above); and, if the work  
is an executable linked with the Library, with the  
complete machine-readable “work that uses the  
Library, as object code and/or source code, so that  
the user can modify the Library and then relink  
to produce a modified executable containing the  
modified Library. (It is understood that the user  
who changes the contents of definitions files in the  
Library will not necessarily be able to recompile the  
application to use the modified definitions.)  
5. A program that contains no derivative of any portion  
of the Library, but is designed to work with the Library  
by being compiled or linked with it, is called a “work  
that uses the Library. Such a work, in isolation, is not  
a derivative work of the Library, and therefore falls  
outside the scope of this License.  
However, linking a “work that uses the Library” with  
the Library creates an executable that is a derivative  
of the Library (because it contains portions of the  
Library), rather than a “work that uses the library. The  
executable is therefore covered by this License. Section  
6 states terms for distribution of such executables.  
Wireless-G PrintServer  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Software License Agreement  
Appendix E  
b) Use a suitable shared library mechanism for linking  
8. You may not copy, modify, sublicense, link with, or  
distribute the Library except as expressly provided  
under this License. Any attempt otherwise to copy,  
modify, sublicense, link with, or distribute the Library  
is void, and will automatically terminate your rights  
under this License. However, parties who have received  
copies, or rights, from you under this License will not  
have their licenses terminated so long as such parties  
remain in full compliance.  
with the Library. A suitable mechanism is one that  
(1) uses at run time a copy of the library already  
present on the user’s computer system, rather than  
copying library functions into the executable, and  
(2) will operate properly with a modified version of  
the library, if the user installs one, as long as the  
modified version is interface-compatible with the  
version that the work was made with.  
9. You are not required to accept this License, since you  
have not signed it. However, nothing else grants you  
permission to modify or distribute the Library or its  
derivative works. These actions are prohibited by law if  
you do not accept this License.Therefore, by modifying  
or distributing the Library (or any work based on the  
Library), you indicate your acceptance of this License  
to do so, and all its terms and conditions for copying,  
distributing or modifying the Library or works based  
on it.  
c) Accompany the work with a written offer, valid  
for at least three years, to give the same user the  
materials specified in Subsection 6a, above, for a  
charge no more than the cost of performing this  
distribution.  
d) If distribution of the work is made by offering access  
to copy from a designated place, offer equivalent  
access to copy the above specified materials from  
the same place.  
e) Verify that the user has already received a copy of  
these materials or that you have already sent this  
user a copy.  
10. Each time you redistribute the Library (or any work  
based on the Library), the recipient automatically  
receives a license from the original licensor to copy,  
distribute, link with or modify the Library subject  
to these terms and conditions. You may not impose  
any further restrictions on the recipients’ exercise of  
the rights granted herein. You are not responsible  
for enforcing compliance by third parties with this  
License.  
For an executable, the required form of the “work that  
uses the Library” must include any data and utility  
programs needed for reproducing the executable from  
it. However, as a special exception, the materials to be  
distributed need not include anything that is normally  
distributed (in either source or binary form) with the  
major components (compiler, kernel, and so on) of the  
operating system on which the executable runs, unless  
that component itself accompanies the executable.  
11. If, as a consequence of a court judgment or allegation  
of patent infringement or for any other reason (not  
limited to patent issues), conditions are imposed on  
you (whether by court order, agreement or otherwise)  
that contradict the conditions of this License, they do  
not excuse you from the conditions of this License. If  
you cannot distribute so as to satisfy simultaneously  
your obligations under this License and any other  
pertinent obligations, then as a consequence you may  
not distribute the Library at all. For example, if a patent  
license would not permit royalty-free redistribution of  
the Library by all those who receive copies directly or  
indirectly through you, then the only way you could  
satisfy both it and this License would be to refrain  
entirely from distribution of the Library.  
It may happen that this requirement contradicts the  
license restrictions of other proprietary libraries that  
do not normally accompany the operating system.  
Such a contradiction means you cannot use both  
them and the Library together in an executable that  
you distribute.  
7. You may place library facilities that are a work based  
on the Library side-by-side in a single library together  
with other library facilities not covered by this License,  
and distribute such a combined library, provided that  
the separate distribution of the work based on the  
Library and of the other library facilities is otherwise  
permitted, and provided that you do these two  
things:  
If any portion of this section is held invalid or  
unenforceable under any particular circumstance,  
the balance of the section is intended to apply, and  
the section as a whole is intended to apply in other  
circumstances.  
a) Accompany the combined library with a copy of the  
same work based on the Library, uncombined with  
any other library facilities. This must be distributed  
under the terms of the Sections above.  
It is not the purpose of this section to induce you to  
infringe any patents or other property right claims or  
to contest validity of any such claims; this section has  
the sole purpose of protecting the integrity of the free  
software distribution system which is implemented  
by public license practices. Many people have  
made generous contributions to the wide range of  
b) Give prominent notice with the combined library of  
the fact that part of it is a work based on the Library,  
and explaining where to find the accompanying  
uncombined form of the same work.  
Wireless-G PrintServer  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Software License Agreement  
Appendix E  
software distributed through that system in reliance  
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE,  
THERE IS NO WARRANTY FOR THE LIBRARY, TO THE  
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT  
WHENOTHERWISESTATEDINWRITINGTHECOPYRIGHT  
HOLDERS AND/OR OTHER PARTIES PROVIDE THE  
LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND,  
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT  
NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND  
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD  
THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE  
COST OF ALL NECESSARY SERVICING, REPAIR OR  
CORRECTION.  
on consistent application of that system; it is up to  
the author/donor to decide if he or she is willing to  
distribute software through any other system and a  
licensee cannot impose that choice.  
This section is intended to make thoroughly clear  
what is believed to be a consequence of the rest of this  
License.  
12. If the distribution and/or use of the Library is restricted  
in certain countries either by patents or by copyrighted  
interfaces, the original copyright holder who places  
the Library under this License may add an explicit  
geographical distribution limitation excluding those  
countries, so that distribution is permitted only in or  
among countries not thus excluded. In such case, this  
License incorporates the limitation as if written in the  
body of this License.  
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW  
OR AGREED TO IN WRITING WILL ANY COPYRIGHT  
HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY  
AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED  
ABOVE, BE LIABLE TO YOU FOR DAMAGES,  
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR  
CONSEQUENTIAL DAMAGES ARISING OUT OF THE  
USE OR INABILITY TO USE THE LIBRARY (INCLUDING  
BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING  
RENDERED INACCURATE OR LOSSES SUSTAINED BY  
YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY  
TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF  
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED  
OF THE POSSIBILITY OF SUCH DAMAGES.  
13. The Free Software Foundation may publish revised  
and/or new versions of the Lesser General Public  
License from time to time. Such new versions will be  
similar in spirit to the present version, but may differ in  
detail to address new problems or concerns.  
Each version is given a distinguishing version number.  
If the Library specifies a version number of this License  
which applies to it andany later version, you have the  
option of following the terms and conditions either of  
thatversionorofanylaterversionpublishedbytheFree  
Software Foundation. If the Library does not specify a  
license version number, you may choose any version  
ever published by the Free Software Foundation.  
END OF TERMS AND CONDITIONS  
END OF SCHEDULE 3  
14. If you wish to incorporate parts of the Library into  
other free programs whose distribution conditions are  
incompatible with these, write to the author to ask for  
permission. For software which is copyrighted by the  
Free Software Foundation, write to the Free Software  
Foundation; we sometimes make exceptions for  
this. Our decision will be guided by the two goals of  
preserving the free status of all derivatives of our free  
software and of promoting the sharing and reuse of  
software generally.  
Schedule 4  
If this Linksys product contains open source software  
licensed under the OpenSSL license:  
This product includes software developed by the  
OpenSSL Project for use in the OpenSSL Toolkit.  
This product includes cryptographic software written by  
Eric Young ([email protected]).  
This product includes software written by Tim Hudson  
NO WARRANTY  
In addition, if this Linksys product contains open  
source software licensed under the OpenSSL license  
then the license terms below in this Schedule 3 will  
apply to that open source software. The license terms  
below in this Schedule 3 are from the public web site at  
The OpenSSL toolkit stays under a dual license, i.e. both  
the conditions of the OpenSSL License and the original  
SSLeay license apply to the toolkit. See below for the  
actual license texts. Actually both licenses are BSD-style  
Open Source licenses. In case of any license issues related  
to OpenSSL please contact [email protected].  
Wireless-G PrintServer  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Software License Agreement  
Appendix E  
OpenSSL License  
Original SSLeay License  
Copyright © 1998-2007 The OpenSSL Project. All rights  
reserved.  
Copyright © 1995-1998 EricYoung ([email protected])All  
rights reserved.  
Redistribution and use in source and binary forms, with  
or without modification, are permitted provided that the  
following conditions are met:  
This package is an SSL implementation written by Eric  
Young ([email protected]).  
The implementation was written so as to conform with  
Netscape’s SSL.  
1. Redistributions of source code must retain the above  
copyright notice, this list of conditions and the  
following disclaimer.  
This library is free for commercial and non-commercial  
use as long as the following conditions are adhered to.  
The following conditions apply to all code found in this  
distribution, be it the RC4, RSA, lhash, DES, etc., code; not  
just the SSL code. The SSL documentation included with  
this distribution is covered by the same copyright terms  
except that the holder is Tim Hudson (tjh@cryptsoft.  
com).  
2. Redistributions in binary form must reproduce the  
above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or  
other materials provided with the distribution.  
3. All advertising materials mentioning features or  
use of this software must display the following  
acknowledgment: “This product includes software  
developed by the OpenSSL Project for use in the  
OpenSSL Toolkit. (http://www.openssl.org/)”  
Copyright remains Eric Young’s, and as such any Copyright  
notices in the code are not to be removed.  
If this package is used in a product, Eric Young should be  
given attribution as the author of the parts of the library  
used. This can be in the form of a textual message at  
program startup or in documentation (online or textual)  
provided with the package.  
4. The names “OpenSSL Toolkit” and “OpenSSL Project”  
must not be used to endorse or promote products  
derived from this software without prior written  
permission. For written permission, please contact  
Redistribution and use in source and binary forms, with  
or without modification, are permitted provided that the  
following conditions are met:  
5. Products derived from this software may not be called  
“OpenSSLnor may “OpenSSLappear in their names  
without prior written permission of the OpenSSL  
Project.  
1. Redistributions of source code must retain the  
copyright notice, this list of conditions and the  
following disclaimer.  
6. Redistributions of any form whatsoever must retain  
the following acknowledgment:“This product includes  
software developed by the OpenSSL Project for use in  
the OpenSSL Toolkit (http://www.openssl.org/)”  
2. Redistributions in binary form must reproduce the  
above copyright notice, this list of conditions and the  
following disclaimer in the documentation and/or  
other materials provided with the distribution.  
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT  
“AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES,  
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR  
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT  
SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE  
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,  
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,  
BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE  
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;  
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND  
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,  
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR  
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF  
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF  
SUCH DAMAGE.  
3. All advertising materials mentioning features or  
use of this software must display the following  
acknowledgement:  
“This product includes cryptographic software written  
by Eric Young ([email protected])”  
The word ‘cryptographic’ can be left out if the routines  
from the library being used are not cryptographic  
related.  
4. IfyouincludeanyWindowsspecificcode(oraderivative  
thereof) from the apps directory (application code)  
you must include an acknowledgement:“This product  
includes software written by Tim Hudson (tjh@  
cryptsoft.com)”  
This product includes cryptographic software written by  
Eric Young ([email protected]). This product includes  
software written by Tim Hudson ([email protected]).  
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND  
ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,  
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE  
AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY  
Wireless-G PrintServer  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Software License Agreement  
Appendix E  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,  
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT  
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR  
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS  
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY  
OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,  
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)  
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,  
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
Thelicenseanddistributiontermsforanypubliclyavailable  
version or derivative of this code cannot be changed. i.e.  
this code cannot simply be copied and put under another  
distribution license [including the GNU Public License.]  
END OF SCHEDULE 4  
8112010B-AI  
Wireless-G PrintServer  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Learning Resources Baby Toy LER 3661 User Manual
LG Electronics DVD Player DN899 User Manual
Likko MP3 Player LKM01 User Manual
Line 6 Laptop Pilot Enhandbook User Manual
Link electronic Stereo Amplifier LEI 555 User Manual
Lux Products Thermostat TX9000TS User Manual
Magic Chef Convection Oven MCSGC12B User Manual
Marantz Projector VP 12S4 User Manual
Maxtor Computer Drive STM302504OTD3E5 RK User Manual
Midland Radio Two Way Radio LXT320 Series User Manual